Search Documents

By D A. Williams, P J. Chapman

The acceptable rate of rise of the tailings beaches on upstream-raised tailings storage facilities (TSFs) is critical to life of mine planning. This is illustrated through a case study in Western Australia presented in this paper. Accurate estimates of expected beach slopes, the maximum rate of rise at which the tailings can be placed, and the dry density that the tailings solids will achieve after deposition (stored density) are required in order to design TSFs that will allow upstream raises to be constructed safely and economically. Where operations have been occurring for some time, these three parameters are able to be measured and can be well-defined. If process plant throughputs are proposed to increase through mine expansion, for example, increasing the rate of rise of the tailings can compromise the potential for upstream TSF raising, thus influencing the viability of such an expansion, the timing for its implementation, and significantly increase costs.This paper outlines how rate of rise can be a key constraint, and that ‘rules of thumb’ that are typically applied may not result in the outcomes they were meant to achieve. An example of an experimental method to justify an increase to the ‘rule of thumb’ ~2.5 m/year limit for gold tailings in a semi-arid climatic setting is discussed, followed by rate of rise modelling that ultimately framed the decision-making process for a mine expansion. The rate of rise modelling method was adopted to carefully distribute tailings deposition across four TSFs, comprising nine separate tailings cells, in order to maintain appropriate rates of rise. The implications resulting from various deposition splits are presented, including the need for expansion. In addition, this paper outlines the effect of rate of rise on the state (density) of the tailings after deposition, and provides commentary on how anecdotally acceptable rates of rise, based on the aforementioned ‘rule of thumb’ of 2.5 m/year may not provide assurance of geotechnical stability through the tailings achieving a dilative state, as has been thought in the past. An example of the influence of rate of rise on the state of the tailings, with respect to air-drying and the critical state line (CSL) for the material, is presented. The data indicate that reducing the rate of rise may allow a higher dry density to be achieved through air-drying (evaporative desiccation), sufficient to move the material from the contractive to the dilative zone (i.e. from above the CSL, to sufficiently below it).CITATION:Chapman, P J and Williams, D A, 2018. The importance of rate of rise in life-of-mine planning of an upstream raised tailings storage facility – a case study, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 350–360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By L Bergin, D J. Williams, S Islam, T A. Vangsness

The flooding of open strip coal mines in the Bowen Basin and Hunter Valley Coalfields of Eastern Australia has the potential to soften the spoil and floor materials to produce “mud”. This mud can act as a slip plane or weak zone when spoil is dumped into it, resulting in geotechnical instabilities. Once mud has formed, typical handling techniques include its costly removal by mechanical means, or its isolation and capping.There are little data available on the moisture state and shear strength of the capped mud. To investigate the effectiveness of isolation and capping, research has been conducted using a large slurry consolidometer (150 mm in diameter by up to 410 mm in height) to simulate capping in situ. Once consolidated, the mud was subjected to shear strength testing in a direct shear box measuring 60 mm by 60 mm by about 20 mm high. The shear strength of the consolidated mud was compared to that of competent, fresh spoil, a mixture of spoil and mud, and to completely degraded spoil (mud alone).These results have been used as inputs in stability calculations using the commercial computer program Slide 7.0, which demonstrates the strong influence of consolidation of the mud on overall low wall slope stability. The results provide insight into the design and construction of capping to isolate in-pit mud.CITATION:Vangsness, T A, Williams, D J, Islam, S, Smith, A and Bergin, L, 2018. Consolidation and shear strength testing and stability analysis of coal mine spoil degraded to mud, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 97–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By R Stead

So many ceramics look the same, but are they?In the past 20 years, there have been significant changes in the materials available, as well as changes to the supply chain, for ceramics used in wear applications in the hard rock mining industry. The biggest change in supply has been from the Chinese market, with many suppliers promoting their products as æstate of the artÆ. Some of them are state of the art, but are they all? There will be some concluding remarks in this respect.There are still some outstanding new developments coming from the more traditional suppliers and these should not be ignored. However, as an end user, how can one be sure that the product received meets the technical specifications of that material?This paper will address some of the questions on how to differentiate between different materials by giving a technical overview of the current (but not exclusive) range of popular ceramics, plus incorporating how these ceramics are used in process plant products by presenting case studies. The presentation will include technical data coupled with micrographs of various ceramics to illustrate just why they are different.It will also be shown that by careful selection of the wear material, it is possible to gain significant benefit when using superior materials in an ore processing plant. The impact of cost of the products, life, process efficiency, and reduced maintenance costs will be considered using cyclone components as an example.The properties (including the microstructures) of the various ceramics will be compared to the application in order to get some understanding of what is considered good or bad.Misra and Finnie (1982) summarised their paper, æA review of Abrasive Wear of MetalsÆ by saying:à it is difficult to give guidelines for selecting materials for abrasive wear resistance. Each application is a different one, and a design engineer has to take into account various other factors such as impact, fatigue and corrosion which are often coupled with abrasive wear. The same applies to ceramics.CITATION:Stead, R, 2013. Applications of ceramic wear materials in the gold industry, in Proceedings World Gold 2013, pp 325-330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By G Corbett

Epithermal Au-Ag deposits form in the upper 1 km of the crust and are therefore best preserved in the less eroded Pacific rim arcs, although also recognised elsewhere. Two profoundly different ore fluid types give rise to low and high-sulfidation styles apparent as variations in ore and gangue mineralogy as well as characteristic zoned wall rock alteration. Low sulfidation epithermal Au deposits are derived from near neutral composite magmatic-meteoric fluids and divided into a group with a stronger intrusion association within arcs grading in time and space from: quartz-sulfide Au + Cu, to carbonate-base metal Au, and the epithermal quartz Au + Ag, whereas in strongly extensional settings the influx of meteoric waters promotes the development of chalcedony-ginguro banded Au-Ag epithermal veins. In the presence of continental crust particularly in Latin America polymetallic Ag-Au veins represent a Ag-rich equivalent of carbonate-base metal Au and passes upwards to chalcedony-ginguro Au-Ag style. By contrast high-sulfidation epithermal deposits are deposited from an acidic magmatic fluid which provided characteristic hydrothermal alteration by reaction with wall rocks grading outwards as mineral assemblages dominated by: vughy silica, alunite, pyrophyllite-diaspore, dickite-kaolin and then illite-smectite neutral clays. Au mineralisation is commonly refractory with enargite deposited dominantly later within the silica zone.Exploration for epithermal Au deposits benefits from an understanding of the controls to mineralisation which commonly give rise to the development of ore shoots with widest and highest Au grade ore zones. In low-sulfidation systems a combination of competent host rocks, dilatant structures, higher grade styles of mineralisation and efficient mechanism of Au deposition, contribute towards ore shoot formation. High-sulfidation epithermal Au systems occur in permeable volcanic and breccia host rocks which are linked by major structures to the magmatic source.CITATION:Corbett, G, 2013. Pacific Rim epithermal Au-Ag, in Proceedings World Gold 2013 , pp 5-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By H S. Welideniya, K Ekanayake

Carbon rich graphite deposits found in Sri Lanka are of inorganic origin and they occur as narrow steeply dipping veins. The vein width of these deposits varies from a few centimetres to metres, with an average vein thickness of 1 m. It is believed that the carbon rich fluid intruded into fracture zones under high pressure and the temperature has crystallised into graphite. This process has also generated many minuscule graphite veins centred on main mineralisation, which has reduced the host rock overall rock mass rating. These discontinuities could also be considered as joints with graphite infill. Graphite mining at Bogala Mines, Sri Lanka is a unique example of narrow vein mining faced with numerous wall stability issues resulting from weak graphite infilled joints.The Bogala vein type graphite orebody has an average vein width of 1 m. Overhand cut-and-fill mining method is used for stoping. The stope consists of two boundary winzes for material handling, access and ventilation. Mining is done on the strike of the vein and the average mining slice height is 2 m. A void to the height of one mined slice is left below the mining level during mining. Waste rock resulting from vein blasting and mine development is dropped into this void as fill rock. Any void height left greater than a single slice height will increase stresses in the stoping zone. This will increase formation of rock blocks and their effective separation from wall rocks. Split miniscule veins occurring around main mineralisation intensifies rock block formation in an environment of mining induced stress release. Consequently, any rock blocks sliding into stopes on graphite infilled joints will behave under constant normal stiffness (CNS) conditions and their shear strength will converge rapidly towards remoulded shear strength of graphite alone. Unlike with general infill deposited in joints, graphite has a very low friction angle and with its slippery nature, a small thickness may affect in great deal to reduce joint shear strength.In addition to immediate filling of excavated voids, controlled vein blasting and spot bolting have improved mine safety. Furthermore, rock bolts connected to each other through iron plates and anchored to anchor bolts installed in non-fractured solid rock are practiced to stabilise rock falls and wedge failures in narrow vein graphite mining. These practices have significantly contributed to safe mining without any rock bursts and catastrophic failures.CITATION:Welideniya, H S and Ekanayake, K, 2012. Challenges faced by narrow vein graphite mining and influence of graphite infill on wall stability, in Proceedings Narrow Vein Mining 2012 , pp 71-76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By B Olsson, R Norman, M Volz

Australia has seen unprecedented demand for coal exports in the last ten years and this demand is set to expand further still according to many analysts. This rapid increase in demand has placed pressure on multi-user coal chains to guarantee the capability to meet the required demand, in terms of both current operations and capacity expansion.The projects required to deliver these forecast tonnages take place in an increasingly complex commercial and technical environment. These challenges include brownfield and greenfield projects, multiple rail and terminal service providers as well as a myriad of mine operators, all needing to operate in an increasingly integrated manner to get the most out of expensive shared assets.Increasing complexity and integration drives the need for more holistic and sophisticated analysis tools. The capacity of coal chain subsystems, such as mine, rail and port, can no longer be determined effectively in isolation. Understanding the nature of the interactions between these subsystems and the resultant capacity of the integrated system is the key to maximising value. TSG advocates the use of a total integrated system approach to understand the behaviour and performance of complex coal chains.Recently, TSG has worked in conjunction with the Integrated Logistics Company and a number of stakeholders in the Dalrymple Bay Coal Chain to deliver the first independent system master plan. This master plan has provided a quantitative and rational assessment of coal chain capacity in its current state and a prediction of its capacity once a pipeline of committed capacity improvements is in place. It is underpinned by a highly detailed discrete-event simulation model of the complete coal chain as an integrated system, including mine load-outs, rail, terminal and port operations.This paper provides an overview of the study and describes the differences between subsystem and total integrated system model performance.

Sep 26, 2011

By S Utili, A Agosti

The Overall Slope Angle (OSA) of pitwalls plays a crucial role in the financial return of an open pit mine. In current practice, pitwall profiles are designed to be planar in cross-section within each rock layer, ie the profile inclination across each layer tends to be constant. A new slope design software, OptimalSlope, has been recently proposed to determine the geotechnically optimal profile shapes for the pitwalls of mines. OptimalSlope seeks the solution of a mathematical optimisation problem where the overall steepness of the pitwall to be designed is maximised for an assigned stratigraphy, rock properties (unit weight and strength) and Factor of Safety. The geometry of the benches is provided as input to OptimalSlope. The results obtained so far on three mine case studies in isotropic rock masses (Utili et al, 2022; Agosti et al, 2021a, 2021b) show that optimal profiles are up to 5° steeper than their planar counterparts – ie the planar profiles exhibiting the same FoS – leading to realising significant saving on waste rock and as a consequence Net Present Value increments and carbon footprint reductions. OptimalSlope algorithms have been modified to deal with anisotropic rock masses characterised by direction dependent shear strength. In the paper, the case of rock masses in banded iron formations (BIF) is tackled. A data set of anisotropic rock shear strengths typical of Western Australia is considered. The Snowden modified nonlinear model was employed to characterise the anisotropy of the rock mass shear strength. From the OptimalSlope simulations performed emerges that optimal pitwall profiles can increase significantly the Overall Slope Angle in comparison with planar profiles featured by the same Factor of Safety. LEM stability analyses of all the profiles were also performed by Rocscience Slide 2 to independently verify the FoSs of the optimal profiles obtained.

Nov 29, 2022

By P Wahyono, H Vega, S Riza, P Vergara, P Gonzalez-Carbonell

PT Freeport Indonesia (PTFI), operating in the Ertsberg Mining District in the Province of Papua, is developing the Grasberg Block Cave copper-gold mine. The site aims to output 160 000 t/d and will be located underneath the current Grasberg Open Pit. Initial studies of the potential to develop a block cave mine in the Grasberg orebody have revealed that the mine will require significant volumes of air. The Grasberg Block Cave (GBC) project requires four primary fans (3750 kW each) to support production at full capacity.Fan #1 commissioning was accomplished successfully on 9 February 2012. However, Fan #2 chamber, which is separated by a 20 m pillar, had not been completed. The main challenge was Fan #2 chamber still needed to be benched. The risk of damage to the critical infrastructure in Fan #1 chamber, including ground support, cracks in pedestals, and misalignment in the impeller shaft were considered. The challenges were blasting the bench without damaging the surrounding infrastructure, completing the work safely and meeting the schedule. This was achieved with the engineering control methodology. This paper summarises the benching process of Fan #2 chamber and its impact upon Fan #1.CITATION:Vega, H, Riza, S, Gonzalez-Carbonell, P, Wahyono, P and Vergara, P, 2013. Excavating an underground primary fan chamber that is adjacent to a fully operational primary fan in PT Freeport Indonesia's Grasberg Block Cave Mine, in Proceedings The Australian Mine Ventilation Conference , pp 115-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By C D. Rose

"The primary objective of this paper is to demonstrate a different approach to predicting and verifying mechanical sampling system precision. Early in the year 2011 an experiment was conducted to evaluate the sampling precision being obtained by a three-stage falling-stream mechanical sampling system for coal owned and operated by Peabody Energy. This system collects samples from lots averaging approximately 14000 t being loaded onto rail cars at a flow rate averaging about 9000 t/h. In phase 1 of the experiment, a total of 60 increments were collected in a two day period at preassigned intervals using a cross-belt sampler located on a conveyor belt feeding a silo upstream of the sampling system under evaluation. Coal variability parameters were calculated from the resulting laboratory analysis data using the gauge-invariant fractal model developed by the author.Estimates of precision of the three-stage system as a function of the number of increments were calculated using the variability parameters determined in phase 1. In phase 2 of the experiment, duplicate samples of 30 lots of coal were taken by the three-stage sampling system, enabling calculations of the precision being achieved by the system. Phase 2 precision estimates are in reasonable agreement with those of phase 1. Conclusions drawn from the experiment include the following: Experimental variograms or the equivalent correlograms are essential in understanding sampling issues and for designing a sampling system to meet specific precision requirements. Consensus coal sampling standards provided by ISO and ASTM may be improved by treating all stages of a mechanical sampling system as æsamplingÆ rather than considering downstream sampling stages as æsample preparationÆ, to be treated in a separate part of the document. The coal industry would profit from use of methodology for routinely monitoring the overall measurement precision and the precision of the individual components of measurement: sampling, sample preparation and laboratory testing. This would not only give necessary credence to the measurement results but would also no doubt, lead to more efficient sampling system designs.CITATION:Rose, C D, 2012. Evaluation of precision being obtained by a three-stage sampling system for coal, in Proceedings Sampling 2012, pp 115-124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By F H. Henrfquez, A G. Oroz

Design and operating conditions of large size mechanical flotation cells were evaluated by comparing them with actual operating conditions in a plant. The objective was to determine the time scale-up factor, typically based on empirical rules. Experiments were conducted on the rougher flotation circuit at Minera Escondida Ltd. The circuit consisted of self-aerated mechanical cells of 160 m3, arranged in six parallel banks with nine cells each. The rougher circuit flotation kinetics were evaluated from direct sampling and local mass balances around each cell of the bank. Adjusted overall mass balances were also developed. This information was used to fit different kinetic flotation models, and it was found that the rectangular distribution function was the most appropriate to describe the distributed rate constant for industrial operation. Then, a rougher flotation simulator was developed to describe the actual operation in terms of the operating variables (mass flowrate, solid percentage, feed grade) and the actual volumetric flowrate entering to each cell. In this study feed pulp samples were taken in parallel from the rougher circuit and were simultaneously floated in the laboratory. The kinetic behaviour was then modelled at a laboratory batch scale in order to determine the time scale-up factor between laboratory batch flotation data and industrial size flotation. The time scale-up factor observed for large sized cells, 160 m3, was found to be reasonably similar to those previously determined for self-aerated mechanical cells, but of lower size, operating at similar recoveries. In addition, the relative effect of mixing, between laboratory batch and an industrial flotation bank, was quantified by the parameter, separating the impact that kinetic and mixing changes have on the time scale-up factor. In general, the rougher flotation operation was found to reach the predicted metallurgical target, and the optimal separability criterion was also respected. The diagnostic generates information about the internal state of the process and helps to identify potential improvements for design, operation and control of the circuit.

Jan 1, 2005

By M Uceda, E Guerra, Y Choi, J L. Shepherd

In this paper we describe the leaching characteristics of pure gold in thiosulfate solutions that contain a known chelator; meso-2,3-dimercaptosuccinic acid (DMSA). The interfacial and chemical characterisation of the system was accomplished using both electrochemical methods and inductively coupled plasma mass spectrometry (ICP-MS) analysis after pure gold samples were exposed to solutions composed of 65 mM Na2S2O3, 1 mM NaOH and a range of DMSA concentrations. In the absence of DMSA, cyclic voltammetry revealed the onset of thiosulfate mediated gold dissolution, the degree of which was reduced at more positive potentials due to the formation of oxidised thiosulfate products on the gold surface. The addition of small amounts of DMSA (<10 ¦M) to the electrolyte resulted in minor changes to the voltammograms indicating a subtle interaction of the additive with the gold surface that may improve leaching. However, at higher concentrations of DMSA (up to 100 ¦M), electrochemical evidence suggests the formation of new oxidation products in solution as well as the formation of more compact monolayers of DMSA on the surface, which contribute to partial repassivation of the surface. The influence of DMSA on thiosulfate leaching of pure gold electrodes at the open circuit potential for a period of 90 minutes was tested and the corresponding gold leaching performance evaluated with ICP-MS analysis. Our data shows that small amounts of DMSA (1 ¦M) doubled the amount of total gold in solution when compared to the same study in the absence of the additive. However, higher concentrations (5 ¦M DMSA) reduced the overall amount of dissolved gold. These results may point to a mechanism where small amounts of DMSA improve leaching by adsorbing onto the surface in a highly defective monolayer that partially blocks or disrupts the formation of passivation products caused by thiosulfate oxidation, but excess DMSA can limit the leaching process itself by forming too coherent a monolayer on the gold surface.CITATION:Uceda, M, Choi, Y, Shepherd, J L and Guerra, E, 2013. Investigating the influence of meso-2,3-dimercaptosuccinic acid on thiosulfate leaching of bulk gold electrodes, in Proceedings World Gold 2013 , pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By N Haque

Base metal ores contain low levels of toxic/hazardous elements such as arsenic, antimony, bismuth, cadmium, lead and mercury. Given the large tonnage of base metal ores mined and processed each year globally, the accumulated mass of minor elements introduced into the biosphere is large and could be expected to have a significant environmental impact. Life cycle analysis (LCA) is a methodology that has been developed to assess the environmental impacts of material supply chains over their entire life cycle. Assessing the toxicity impacts of metallic wastes and incorporating these impacts into LCA methodology is not a simple task given the complexity of the issue. However, research and methodology development is in progress internationally to address this. Despite limitations concerning the lack of a coherent framework for characterising the toxicity impacts of metals, including issues such as bioavailability, a study was carried out to give first estimates of the relative toxicity impacts of various waste streams from metal production processes. The wastes considered were: red mud; sulfide tailings (copper, nickel, lead/zinc); lead/zinc slags; synthetic rutile residue; iron oxide residue; and copper slags and anode slimes. These toxicity estimates can be considered the æworst caseÆ scenario for these wastes, where all the metals present are bioavailable. Combining estimates of the amounts of the various waste streams produced in Australia each year with the toxicity results showed that despite their relatively low human toxicity impact per unit mass compared to some other waste streams, red mud and the various sulphide tailings had the highest annual human toxicity load on the environment, along with copper smelting slag and dust. Data from the pH dependent leaching test reported in the literature were assumed to represent first approximations of metal bioavailability and used to compare the two approaches to estimating the toxicity impacts of red mud.

Jan 1, 2009

By S Gomez-Hernandez, P D. Munro

Filtered dry stack tailing storage facilities offer many advantages over thickened tailing storage facilities and yet, most of the mining companies still prefer the latter.Some of the advantages of filtered dry stack tailing storage facilities are: increased structural integrity of the tailing storage facility, which is even more critical in areas of high seismicity, close to nearby communities or environmentally sensitive areas; maximised water recovery which is particularly important in arid environments where water is an extremely valuable resource and its supply is regulated; optimised recovery of valuable metals in the process water, avoiding high cyanide concentration going to detoxification (both aspects haven’t been emphasised enough in technical papers on this subject); optimised space to store the tailings in mountainous regions; minimised elevation of embankment height, providing a safe option to store the tailings in places where there is limited area available; simplified license approval to operate where the tailing facility is a big issue; and avoidance of potential problems with nearby communities.Filtered dry stack tailing storage facilities have some disadvantages such as: technology limitations in operations that process high throughputs (eg >50 000 tpd) as they require many filters resulting in high maintenance and operating costs; higher capital cost; low efficiency in the filtration process, particularly in ores with high clay content increasing operating problems and capital cost; the new technology risk with possible debottlenecking issues and a longer time to achieve the design throughput; and the need to treat larger water flow rates when the water balance is negative.This paper analyses: the operating practices of Mexican gold and silver operations using filtered dry stacking storage facilities; implementation issues, advantages and disadvantages; quantifiable reductions in gold and silver losses and actual lower detoxification cost; and current trends to use filtered dry stacking storage facilities in new projects. The data gathered raises questions about (a) the need to collect data on tailings filterability, and; (b) reducing the current high operating cost of tailings filtration.CITATION:Espinosa-Gomez, R, Gomez-Hernandez, S and Munro, P D, 2018. Tailing filtration practices in Mexican gold and silver mines, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 275–282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By R Varden

Friction rock stabilisers, commonly termed ‘Split Sets’, friction rock bolts, or continuous friction coupled bolts are the most widely used rock bolt in the Australian underground metalliferous industry. Historically, they were used for temporary reinforcement, mainly within ore development. However, their use as primary reinforcement has grown with the demand for higher development rates at lower costs. The introduction of galvanisation has increased their longevity and pattern bolting in conjunction with weld mesh, specifically made for use in development headings, has allowed the use of friction rock stabilisers to increase rapidly with development jumbo’s undertaking the installation. The installation of friction rock stabilisers appears to be deceptively simple, particularly when compared to resin encapsulated bolts. The friction rock stabilisers capacity is a function of the borehole parameters, rock mass quality/strength, the bolt dimensions and steel quality, and lastly and perhaps the most important the operator skill levels. However, as in industry we are still seeing common occurrences of friction rock stabilisers not reaching their design pull test capacity. Pull testing the friction rock stabilisers is used to verify the installation of the design capacity. It involves loading the collar of the bolt with a hydraulic ram until the design load is reached or the bolt slips. Pull tests often show failure rates of 20 per cent or higher. This is despite over 40 years of use and with millions of units installed annually. Such high failure rates would suggest there remain issues with the quality of installation. Ground support quality assurance and quality control (QAQC) programs are needed in combination with operator training to ensure that pull test failure rates are kept as low as practical. However, there are times when despite the QAQC being completed the pull test failure rates increase quite suddenly. When this occurs, it is important to conduct a thorough investigation. These investigations often show there are several factors that are not obvious to personnel installing the bolts. To complete a useful investigation, it must also be done methodically, working through the entire process that includes less obvious factors such as steel quality and the calibration of the hydraulic pull test kit. The aim of the paper is to give mine practitioners an understanding of the complexities of friction rock stabilisers, what QAQC requirements they should be doing on-site, what can go wrong during installation and, if necessary, a process of how to conduct investigations into high friction rock stabiliser pull test failure rates.

Mar 29, 2023

By G Capes, L Morizzi, N Mitkas, E Jones, D Grant

This paper describes the mining setting for the sub-level open stoping (SLOS) mining method used at Olympic Dam (OD), and investigates the range of stope performance conditions encountered over 30 years of production, using a qualitative description of the factors influencing performance. Utilising a continuous improvement tool, the Plan-Do-Check-Act (PDCA) process, and a forward-looking rock mechanics program, the intent is to identify the key factors driving productivity and performance to create a stable and achievable long term mine plan.

Mar 15, 2021

By D M. Verster, P L. Gillot, A Kone

Randgold ResourcesÆ MorilaÆs gold leach plant is subjected to uncommon æoxygen stressesÆ. Feed ores exhibit very high oxygen demands, primarily caused by iron sulfides. In addition, ore oxygen demand varies significantly over time, as well as between different feed ore sources. The inability of the Morila gold leach plantÆs oxygenation system to cope with these high and fluctuating oxygen stresses manifested itself in variable gold residue grades, and cyanide consumption rates.Management launched a Morila oxygen system review project during September 2009, with the objective of auditing the performance of the then current oxygenation system, against required performance parameters as calculated from oxygen demands of the various feed ore types and targeted dissolved oxygen levels in the leach train.This paper describes the systematic changes made since 2009 to the Morila oxygen system in four main areas: O2-supply plant, O2-volumes, O2-controls and oxygenation equipment. Data are provided on corresponding improvements in leach plant performance. Theoretical, as well as practical aspects of gold leach oxygenation systems are covered.CITATION:Verster, D M, Gillot, P L and Kone, A, 2013. Oxygenation system upgrades and leach plant performance improvements at Morila Gold Mine - 2009 to 2012, in Proceedings World Gold 2013 , pp 215-224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By R Van Laeren, G Langerak, S Fityus, K Koosmen

Co-disposal of partly-dewatered mixed-plant rejects (MPR) from coal processing into spoil dumps is gaining favour amongst Australian coalmine operators in preference to conventional tailings disposal methods which require a tailings dam. Owing to their often low permeabilities and high degrees of saturation, MPR materials may be prone to the development of excess pore pressures when covered by spoil during routine dump advancement. The likelihood of dump failure will increase if these pore pressure regimes and the associated delay of shear strength development are not accounted for during waste dump design. To date however, little is known about these pore pressure regimes due to the complexities associated with their in situ measurement.This paper describes the in situ measurement of pore pressures in a cell of MPR placed within a coalmine spoil dump. Four vibrating wire piezometers (VWPs) were placed within a cell that was then filled with MPR and allowed to consolidate under self-weight before advancing an adjacent tiphead across the cell. The VWPs recorded the transient pore pressures during MPR placement and dump construction, and their interpretations are described within the context of laboratory measured parameters. Following analysis of the measured pore pressures, their implications on shear strength and dump design are also discussed.CITATION:Koosmen, K, Langerak, G, Simmons, J, Fityus, S and Van Laeren, R, 2015. Field measurement of transient pore pressures within co-disposed processing rejects placed in a spoil dump, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 63–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Player, R de Vries, E Villaescusa, H Saw, R Hassell

The use of cemented rock fill (CRF) for support of open stope walls has increased in the Australian underground mines operations over the last five years due in part to its low capital cost. In open stoping the exposed CRF masses require adequate strength and stiffness, in order to resist the forces and to limit the displacement associated with movements in the rock mass surrounding the excavations. The CRF material preparation often involves the use of large particles, either from crushed rock or from development mining waste sometimes up to 1 m in diameter. However, the use of waste rock, which has a poorly graded particle size distribution may not achieve the required minimum target strength due to segregation and large air voids within the fill mass. This paper describes the optimisation of CRF strength by either crushing the waste rock or the addition of sand to the mix. Both methods increase the level of fines in the mix design. Cylindrical samples having 400 mm diameter and 800 mm heights were prepared for uniaxial compressive strength (UCS) testing. The UCS test was determined using the Western Australian School of Mines (WASM) large-scale static test frame. The laboratory results were compared with a database of large-scale CRF strength mixed without sand from a number of mine sites around Australia. The comparison shows a significant strength development in the CRF mixing with addition of sand for a given cement percentage. Due to the higher strengths achieved by the addition of sand and the crushing of the waste material these CRF types require less cement to achieve the same strength. This has the potential to improve the overall economics of open stope mining due to less dilution of the exposed fill mass.CITATION:Saw, H, de Vries, R, Player, J, Hassell, R and Villaescusa, E, 2017. Optimisation of cemented rock fill strength for open stope support, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 85–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By E Corpuz, J Weissman, S Winter, R Evans

The surface-to-inseam (SIS) directional drilling technique has been utilised at Oaky Creek Coal for more than a decade to predrain both the Oaky No 1 and Oaky North mining areas. The cumulative drilling program constitutes a total of 140 lateral and 200 vertical holes, and 405 km of lateral drilling.The use of SIS gas drainage has been successful with the following site-specific benefits being recognised:ability to drain German Creek seam gas contents to residual gas levels of new mining areas within an 18-month period from commencement of well productionstructural geological verification of the mine design well in advance of development mining occurring in an areaability to conduct successful predrainage of the overlying Aquila seam to reduce subsequent goaf emissions.Appropriate and up-to-date geological knowledge during the design and drilling process is a significant influence to achieving success. Vertical production wells need to be located in a position that is most effective to remove water from hole. The lateral hole should not include intersections with significant geological structure.SIS drilling provides continuous seam roof/floor data to help define seam geometry and locate geological hazards with high accuracy. In faulted ground and with variable seam gradients, SIS data can resolve geological ambiguities from seismic sections and enhance seam correlation that would otherwise be available only from discrete and closely-spaced infill vertical exploration drilling.Here, we review some examples of SIS configurations and practice to highlight key learnings in drilling long inseam holes (up to 1900 m per arm) ahead of development and mining. Aspects on prerequisites, evolution of network design, tolerances and drainage outcomes in a variety of geological situations are discussed as technical basis towards a viable and effective SIS drilling program.CITATION:Corpuz, E, Evans, R, Weissman, J and Winter, S, 2015. Surface-to-inseam (SIS) drilling at Oaky Creek coal mine – SIS design aspects and drilling environment, in Proceedings The Australian Mine Ventilation Conference, pp 93–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

The Rio Tinto Iron Ore group currently estimates grade attributes for mineral resources using ordinary kriging (OK). OK produces a smoothed globally unbiased estimate, but does not capture local variability, which can have significant impact on mine planning and scheduling. The dimensions and the multivariate nature of iron ore deposits make point simulations of whole deposits impractical. With a direct block simulation method the size and speed limitations of point simulations can potentially be overcome, resulting in a viable method for capturing local variability and for providing risk measures into the mine plan and schedules. Some iron ore deposits are highly folded (post mineralisation) and require preprocessing using an unfolding algorithm to properly define the continuity parameters and directions of anisotropy before simulation can proceed. Block co-simulation proceeds in unfolded space and since mine planning require a block-model with regular block-sizes; a regular block-model is unfolded first. This paper discusses a block co-simulation approach that can be used to simulate the irregular blocks resulting from the unfolding process. A section of an iron ore deposit is used for testing the block co-simulation algorithm and the simulation results are compared against the Isatis direct block simulation method. Available blasthole data is also used to validate the behaviour of the block co-simulation algorithm.

Sep 26, 2011