Search Documents

Underground mine ventilation is now com monly simulated on a digital computer. Such a programme, incorporating natural ventilation has been modified by others to account for methane emission and elevated local tempera- tures. At Wollongong University, the pro- gramme was further developed and extensive interactive graphics incorporated such that any view of the three dimensional mine could be viewed, and superimposed upon that view are areas where a nominated parameter has exceeded a particular value - generally at a nominated time after a particular event and usually a fire/explosion of one type or another. A further programme was developed such that up to 20 'times' could be examined at a particu- lar location after say, a fuel rich fire at some other place in the mine. The output from this programme includes a plot of methane 1, smoke 1, temperature, pressure and air flow versus time - a most useful graphic to observe the limits of safe attendance in a particular Airway.

Jan 1, 1983

By B Manda, K L. Sandvik, K Musiwa

Mining and processing of pyrite ore at Iron Duke Mine, north east of Zimbabwe, generates large quantities of acidic mine water as a result of the oxidation of iron sulfides on exposure to air and water used in the drilling and blasting operations. The acid mine drainage (AMD) contains elevated levels of dissolved Fe, Al, Mn and sulfate and has characteristic pH values ranging from about 0.50 to 3.00. Handling and disposal of such a drainage places significant impacts on the economics of the mining operation due to the corrosive nature of the drainage on infrastructure, the limitations placed on water reuse and discharge to the environment under a new law governing effluent discharge. Treated sludge at Iron Duke is chemically unstable, changing pH from ~7 to ~3 within four days after deposition in the evaporation ponds. The effluent does not meet the permitted level of neutral pH, 500 mg/l sulfate and less than 2000 mg/l total dissolved solids. Excessive acid seepage from the evaporation ponds has resulted in contamination of the ground water below the ponds area, which shows high mean annual levels of iron (368.67 mg/l), sulfate (1702.89 mg/l) and low pH (2.86) in addition to other pollutants. This poor quality seepage infiltrates into the nearby Yellow Jacket River, contaminating the public water source. Furthermore, a deterioration of the land area and vegetation adjacent to the tailings dump is also observed. Understanding the controls on the neutralisation of acidic drainage and long-term sludge stability after placement in evaporation ponds is essential to minimise costs of closure requirements and for the protection of environment and human health. This study examined the effects of the master variables pH, redox potential, acidity and alkalinity on acid neutralisation. The results indicate that ferrous hydroxides are not as stable as ferric hydroxides and that proper oxidation of iron also leads to better sludge stability, higher treatment efficiency and a manageable sludge viscosity. Metal hydrolysis and secondary mineral formation at the evaporation ponds under a wide range of pH and redox conditions is responsible for equilibrium shifts in metal reactions, resulting in high potential for metal leaching and mobility. Mechanisms of metal attenuation are also discussed.

Jan 1, 2006

By Gill L. F, Gleeson HB

This paper describes the development of a Computer Aided Design and Drafting based mine planning system in the State Electricity Com- mission of Victoria. The system combines a commercially available CADD system with a commercially available mining/geological package. The methodology used in the establishment of the combined system, the fea- tures of the system and the current status of development are discussed.

Jan 1, 1989

By A D. Campbell

The Homer Tunnel is located in a remote area of the South Island of New Zealand and carries large numbers of tourists to Milford Sound through an avalanche prone area. The tunnel is 1280 m long with a steep ten per cent unidirectional grade descending to the west. Construction of the tunnel began in the 1930s and was completed to a nominal 6 m width in 1954. In 1996, two passing bays were stripped-out to accommodate bi-directional flow of tourist coaches. During all phases of construction and widening there have been episodes of strain bursting.The condition of the tunnel and standard of internal services is below current international practice, principally in terms of; in-tunnel air quality, fire life safety, ground support, and road safety. A number of near-miss events have occurred involving coach fires on the approaches and inside the tunnel. The national road authority, NZTA, is considering a substantial investment to improve amenity and safety of the tunnel.This paper describes the rationale for the proposed upgrade works and the investigations undertaken to enable that design. A holistic approach to road tunnel safety has been adopted that balances the key interrelated safety drivers, namely; tunnel lining, traffic operations, ventilation, power supply and egress while ensuring continuity of safe access to Milford Sound.

Mar 8, 2011

By P D. Munro

"This is a reprise of the paper ‘Back to the Future – Why Change Doesn’t Necessarily Mean Progress’ presented to the Tenth Mill Operators’ Conference in 2009. It was observed that the ‘boom and bust’ cycles of the industry, together with trends in tertiary education and the effects of fly-in fly-out (FIFO) operations raised serious questions about the sustainability of human capital in the mineral processing sector.In 2016 we find ourselves in a ‘bust’ after enjoying a decade of the longest commodity price ‘boom’ in a century. In the ‘boom’ did we:make any technological breakthroughs?put measures in place to improve our human capital, especially in the area of ‘professional formation’?The paper makes observations on the current performance of mineral processing engineers and the organisational milieu in which they operate. It questions whether mineral processing engineers are actually ‘adding value’ at some sites given their organisational and operational practices.Some technical trends are examined and what it might mean for mineral processing engineers.Given the above and demographic trends for mineral industry professionals, changes to the seemingly current laissez-faire model of professional development are proposed.Citation:Munro, P D, 2016. Back to the Future - Still on the Dark Side, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 341–348 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

The non-renewable energy resources of Queensland comprise coal, petroleum (oil and gas), oil shale and uranium. Coal is widely distributed., and has been developed extensively both for export and for use within the State. Proven reserves total 5 390 million tonnes recoverable of coking coal and 5 580 million tonnes recoverable of non-coking; very large resources particularly of non-coking coal are still to be quantified by further drilling. Annual production is of the order of 20 million tonnes of coking coal, principally for export, and 6 million tonnes of non-coking, mainly for power generation within the State. Petroleum resources are meagre in com- parison with those of coal. Initial recover- able reserves of liquids (mainly in the now substantially depleted Moonie Oil Field) totalled only 4.2 million m3. Initial recover- able reserves of gas (mainly in the western Surat and Bowen Basins) totalled 7 800 million m3. Annual production is of the order of 64 thousand m3 of liquids for refining in Bris- bane, and 268 million m3 of gas mainly for production of fertiliser and for industrial and domestic heating, in Brisbane. Prospects are fair for the discovery of additional reserves. Two deposits of oil shale are potentially of economic significance. The Rundle deposit at The Narrows in central Queensland has the

Jan 1, 1979

By L Galisson, E Audigé, D Sowers

Establishing a robust geotechnical instrumentation and construction monitoring plan is one of the keys to the successful delivery of the world’s largest soft-ground bored tunnel in Seattle, Washington. The paper describes and provides a return of experience on current and best practice for monitoring tunnelling projects in urban areas. The owner’s contractual approach is discussed to highlight the flexibility of the design-built contract in achieving equal or better solutions by allowing for the use of innovative technics. Special attention is given to the management and involvement of third parties (building owners, utility owners), including the public, to overcome all challenges faced during the installation of the monitoring system in downtown Seattle for over 1000 instruments. Finally, the authors present the strategies implemented for managing the monitoring data and communicating with the owner, contractor and stakeholders.CITATION:Sowers, D, Galisson, L and Audigé, E, 2014. Current and best practice for monitoring tunnelling projects in urban areas – Alaskan Way bored tunnel, Seattle, Washington, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 441–450 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Blair J. R, Barrett J. R

In many underground mining applications where-dry fill is used, only a token acknowl- edgement of the fill properties is given. It is the aim of this paper to induce mining engineers to consider dry fill as an engineer- ing material rather than a mass to place in unwanted voids. Dry fill is generally cheap, inert and readily available, but it can still contribute to mining performance. In particular, the choice of the dry fill becomes more critical as stope sizes increase, controlled choked draws are used or pillar recovery introduced. Selection must be initiated from an evaluation of the role of the fill in the mining operation. In most cases the fill must be chosen before quarrying begins and an investigation must be made of available sources and appropriate quarrying methods. Some of the properties of fill are described together with evaluation techniques. A com- parison of placement conditions is limited by the complexities of material flow and degrada- tion: However, field and model tests can aid interpretation in these cases. Examples are given of aspects of dry fill selection and their incorporation in mining design.

Jan 1, 1973

By D S. Collins, Z Hosseini, I Pinnock, Y Toya

Microseismic monitoring is regularly used in the mining and geotechnical industries to provide detailed information about rock mass response to operational activities. This paper implements a variable 3D velocity model (VM) at a North American hard rock mine with the aim of further improving the accuracy of seismic event locations. A collapsing method is also used to help analyse two individual seismic event clusters at another North American hard rock mine. In the first case study, the location accuracy of events is shown to improve by moving from a conventional single VM to a variable 3D VM that accounts for voids and different geological domains. The modal average for the event location accuracy improved from 14 m to 5 m when the 3D VM was used. Additionally, the single VM failed to locate 26 per cent of the seismic events that were located by the 3D VM. In the second case study, the distribution of seismic events was further enhanced by using a collapsing method that highlighted planar structures. The collapsing method was performed on two large event sequences that occurred in close proximity and identified different seismic event distributions. One aftershock sequence aligned along a plane, suggesting an activated structure, while the other large event sequence had a more 3D distribution of events, suggesting a complex stress redistribution on smaller structures.CITATION:Pinnock, I, Collins, D S, Toya, Y and Hosseini, Z, 2016. Large event sequence analysis and 3D velocity models for seismic event location accuracy, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 879–884 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Connell JE

The Worthing Mine near Hallett Cove. 20 km southwest of the cite of Adelaide, belongs to Aus- tralia's first mining era, which took place in South Australia between 1841 and 1851 (Figure 1). Oper- ations began in 1849 only six years after the com- mencement of metal mining in Australia at Glen Osmond. Although not as historically significant as Glen Osmond (1841), or the much larger copper mines of Kapunda (1844) or Burra (1845) its importance lies with its Cornish enginehouse and chimney. The Worthing enginehouse, built in 1851-1852 is the oldest remaining in Australia and certainly the most significant relic of Australia's first mining era. Six other stone enginehouses were built during that period: at Kapunda in 1848 and 1850: at Burra in 1849, 1850 and 1851; and at Tungkillo in 1849. All of these houses have long since dis- appeared although the foundations of one (Kapunda, 1850) still remain. The significance of the Worthing site is enhanced by its magnificant environmental setting in the bare, steep valley of Field River. Currently (1986) the Worthing Mine is the only site within the City of Marion which is on the Register of State Heritage Items. The site is also included in the Classified List of the National Trust of South Australia and on the Register of the National Estate.

Jan 1, 1987

By Waghorne E. P

The State Electricity Commission of Victoria is Australia's largest single coal producer. Approximately 19 Mt of coal will be produced in 1989 from the SEC V's newest mine, Loy Yang Open Cut (LYOC), which com- menced overburden stripping operation in October 1982. When the adja- cent Loy Yang Power Station is completed in the late 1990's, LYOC will supply between 35 to 45 Mt/a, depending on power station performance and demand of coal for non-power generation uses. LYOC has been a major challenge for the SECV. It is the biggest single open pit coal mining development undertaken in Australia, with a whole of life capital cost approaching A$1 billion. The mine has supplied a very rapidly growing demand for coal from the expanding power station while developing in breadth, length and depth. Coal demand has consistently been above the figures anticipated during the initial planning because of the substantially improved performance of the 500 MW units of the Loy Yang A Power Station. The superior performance of the LYOC and power station has generated additional electrical energy during the first 5 years of power station operation compared with the initial planning targets- at almost no additional capital cost. This has been a major benefit to the SECV. LYOC will continue to present major challenges for the SECV, particularly in achieving overburden removal and coal reserve targets as development of the open cut continues to full depth over the next 15 years.

Jan 1, 1989

By K G. van den Boogaart, U Mueller

"An accurate prediction of benefit for some types of ore may require not just the ore grade, but a whole compositional characterisation of the estimates; that is, its full mineral composition including waste composition and nuisance elements. An example is Nickel laterite ores, where Ni/Co content must be complemented by estimates of many other elements, as these might have a notable impact on ore processing.Estimates are often obtained with (co-)kriging or co-simulation; however, geostatistics applied to compositional data may yield spurious and inconsistent results because of the constant sum constraint. The log-ratio approach avoids such problems. It proposes a three-step procedure: data are mapped to a set of log ratios of components; for example, the additive log-ratio transformation (alr) transformed scores are modelled with an appropriate fully multivariate geostatistical toolbox; for example, direct/cross-semivariograms and co-kriging or co-simulation results are back-transformed to the original units.Some practical aspects may make the application of this technique difficult: the assumption of Gaussianity and the high dimensionality of the compositions combined with the need for using multivariate methods. This contribution compares several ways of treating compositional data (combining normal score transformation, log-ratio transformations, and minimum/maximum autocorrelation factor (MAF) decomposition) with respect to their ability to generate sensible simulations. The various approaches considered are illustrated with a Nickel laterite data set for which ten variables are available. Both theoretical considerations and illustration results suggest that the best combination is (log)ratio-normal score transform-MAF, in this order. The factors so obtained are closer to Gaussian, approximately spatially decorrelated and can be simulated independently. Simulations can later be recombined to alr-simulations, which in turn may be converted back to point compositions. The resulting simulated compositions are compared with a full Gaussian co-simulation of the raw data. The log-ratio methods show reasonable to good reproduction of mean values, and distribution of the data set and by construction satisfy the total sum constraint, in contrast to the simulations based on raw data for which the total sums fluctuate strongly.CITATION:Mueller, U, Tolosana-Delgado, R and van den Boogaart, K G, 2014. Approaches to the simulation of compositional data – a nickel-laterite comparative case study, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 61–72 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

The Grootegeluk coal beneficiation plant is situated near Ellisras in the Waterberg coal= field in the Transvaal, RSA. At this plant 15 million tons of coal bearing material per annum are beneficiated by means of two-stage heavy medium bath and cyclone plants. Because of the very low yield of 12 % coking coal product, run= ping costs are of the - utmost importance. For this reason extensive tests were carried out to establish the most effective crushing and bene= ficiation methods and suitable aquipment. At the second heavy medium separation stage, the near-gravity material (+ 0,1. g/cc) amounts to 45 % and daily plant performance ana=lysis is required to ensure acceptable plant efficiency. Beneficiation processes for the -0,5 mm coal originally considered were froth flotation, shaking tables, heavy medium cyclones and water- only cyclones. When the froth flotation route was decided upon, further test work was done to enable selection of the equipment most suitable for the particular requirements.

Jan 1, 1987

By A Turns

In a survey conducted by symplexi with underground miners in Australia; 78 per cent of participants believed that ‘safety’ is all about people. If ‘safety’ is about people, then is the mining industry focusing on the wrong thing? It would be fair to say that the mining industry is heavily systems focused. Companies develop a safety management system and use this to show regulators that they comply with legislation – however, that is only half of the picture.

May 5, 2022

The current economic climate and demand for iron ore has resulted in mine operators being prepared to accept aggressive slope designs and associated failures provided that they can be quantified (ie volume of failure and clean up costs, etc) and incorporated into the mining costs, at a feasibility study level. This has numerous implications for pit slope design/geomechanics. Typically when geotechnical engineers conduct slope stability modelling a single value, usually the average or mean value for model input parameters (ie structural orientations, material properties and hydrological conditions) are chosen. The implications resulting from using a single value for model input parameters will vary depending on how the modeller has chosen the value, ie should the modeller choose a mean value from a log-normal distribution of material strengths an optimistic representation of the stability may eventuate, consequently if the designer decides to conservatively downgrade the values by a nominal factor, a pessimistic representation of slope angles may occur, which would result in excessive stripping and mine development costs. A more realistic and representative way to model the inherent variability of geological/geotechnical conditions would be to do so probabilistically. Whereby the modeller can assess the variability of the geological structure as observed/recorded during the core logging process and a similar approach for the material strength properties. The final model output would be a distribution of factors of safety in relation to overall slope angles, ie probabilities of failure for individual slope angles could be determined. This output (graph) could be modified by the mining engineer to incorporate mining costs as well as clean up costs for the respective slope angles and associated failure volumes, ie probabilities of failure. The author intends to provide a detailed overview of the processes involved in deriving a geotechnical design, ie; starting from the data collection phase (core logging/face mapping), through to the data interpretation and formulation of slope parameters; determining the variability and uncertainties associated with each of the process; ensuring that it is adequately captured in the model input parameters; and how the mining engineer could utilise this information to derive final feasibility study mining costs.

Jan 1, 2009

By Harada M, Katsuta S

In order to shorten the time taken to com- plete shield tunnel excavation work, reduce labor costs and to improve safety, an automatic assembly robot system for the segments used has been developed. It was developed in the three years from 1982 until 1984. An experimental assembly system for concrete segments (outer diameter:.3.55m) has been thoroughly tested to confirm that these segments can be fed and assembled automatically (Fig. 1, 2). This report outlines the robot which will be put into practical use in the near future. The robot senses the position of already assem- bled segments by means of position sensors, controls the position and the attitude of the segment to be assembled to allow bolt hole positioning, and completes the automatic assembly of a se;nent by automatically tighten- ing bolts. The six segments which make up one ring can be automatically assembled in about 25 minutes.

Jan 1, 1987

By Upfold RW, Velzeboer MD

An underground mine fire will influence the ventilation equilibrium in several ways which results in a redistribution of the ventilating quantities and pressures throughout the whole mine. The ventilation carries the combustion products which constitute the greatest danger of mine fires through the mine and provides the oxygen on which the intensity of the fire depends. However, as a result of the ventilat- ion disturbances created by the fire, changes in airflow patterns can take place which are not always obvious, especially when the mine is being served by several fans. The use of com- puter simulation techniques allow for the likely effects to be tested and the different ventilation options to be evaluated as an integral part of the overall emergency/rescue planning and control procedures.

Jan 1, 1981

Mr. President, Ladies and Gentlemen, it gives me great pleasure to welcome you, on behalf of the Council and Administration, to this University and extend to you our very best wishes for a most successful and stimulating symposium. We as a College of the University of N.S.W. were always proud of the excellent support we received from your Institute members and the close association that existed between our organisations. Now we have matured into the University of Wollongong and have to stand on our own feet, we will need all the support we can get from such bodies as yours to ensure that we are not only producing graduates but are also playing a vital role in the community. Although there is no planning for a school of Mining Engineering in the near future, we do look forward to this being a viable proposition eventually and we will then be able to offer to your Institute wider facilities for your activities and ones which will embrace both the Mining and Metallurgy phases. Thank you Mr. President.

Jan 1, 1975

The paper describes the preparation of new rail guides, removing existing rails, and replacing with new rails in a vertical winding shaft.INTRODUCTIONThe general practice in coal winding shafts is the use of two cages, with one or more decks in which men and materials are raised or lowered. Winding speeds vary according to depth, the type of winding gear, and whether winding is done in downcast or upcast shafts. Each cage occupies a position between the centre and side of the shaft, with a clearance depending on the type of guides used. The function of the guides is to keep the cage in position throughout the entire depth of the shaft. There are three types of guides, two of which are in general use.1. Selected wood of about 6 in. square section, fixed to the side of buntons.2. Solid strand steel made up similarly to that of an ordinary wire rope, suspended from the head frame with weights attached to the lower end.3. Standard T-rail sections fixed to end or side buntons. Of the three types, 2 and 3 are in general use. The type used in the particular case, the subject of this paper, is T-rails of the standard section used in railway work.GENERAL DESCRIPTION OF SHAFTDetails of the shaft are as follow: Diameter of shaft: 22 ft. inside lining.Depth of shaft: 900 ft., including sump.Concrete lined throughout.VENTILATIONThe ventilation shaft is used for the upcast, through which all vitiated air passes to the main ventilation fan. Quantity of air passing up the shaft is 400,000 cu. ft. per minute. The air is highly saturated during the summer weather and slightly less...

Jan 1, 1947

By E Holloway

The optimisation of an open pit mine can be broadly split into two stages, the first being the ultimate pit optimisation (and subsequent stage designs), and the second being schedule optimisation. Macroeconomic uncertainty clearly impacts on both however interrelationships do also exist. Generally, the opportunity exists for the ultimate pit to be revised during each planning cycle, however when this reprieve is removed the uncertainty for the underlying business increases. As one example, the introduction of an in-pit waste dump can be seen to significantly limit the option to revise the ultimate pit. When in this situation there are two potential risks that present: (i) the long-term price used for the ultimate pit selection is optimistic, and too large of a pit is selected resulting in waste being mined which uncovers material not of a significant value to deliver a profit; (ii) the long-term price used for the ultimate pit selection is pessimistic, too small of an ultimate pit is selected, and ore of realisable economic value left behind. Both of these outcomes are risks and as such can be assessed and quantified. CITATION: Holloway, E, 2018. Incorporating economic variability into a strategic planning framework, in Proceedings Complex Orebodies Conference 2018, pp 88–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018