Search Documents

By S Whitton, W Wimmler, L Wimmler

“Given the increasing scrutiny of the mining industry and its relatively poor record with regards to mine tailings management, increased requirements to minimise water usage (often accompanied by very high costs of water) and the need to demonstrate achievable long-term closure strategies, it is likely that the option of a filtered tailings system will need to be considered in many operations in future.” (Australian Centre for Geomechanics, 2018). Given such a statement as a conference introduction, it is only appropriate that a range of potential technologies are investigated and compared, to create awareness for even underrated but appropriate technologies. The advantages and disadvantages of all technologies need to be considered and analysed. Suppliers are swift to promote their technologies advantages; however aspects of sustainability are not always fully understood. Perhaps a combination of two filtration technologies is appropriate. This paper delves into the technical details, good or bad, of four mechanical dewatering technologies in tailings dewatering and provides insight on an undervalued and, in the author’s opinion, young technology – the screw press.

Jul 1, 2021

By R Wei, Y Peng, D Seaman

This study addresses a widespread problem confronting the mining industry: the deleterious effect of clay minerals in flotation. This problem is seemingly exacerbated by the presence of iron contamination from grinding media. The interaction of clay minerals and grinding media in copper and gold flotation was investigated in this study. A low-clay ore and a high-clay ore were obtained from Telfer to represent different contents of clay minerals, while stainless steel and mild steel grinding rods were used to produce different grinding chemistry, in particular, iron contamination. Flotation tests on an unsized and sized basis were conducted to reveal how clay minerals and grinding media affect copper and gold flotation. Iron contamination and the oxidation of copper minerals were quantified by ethylene diamine-tetra acetic acid (EDTA) extraction. It is interesting to find that both clay minerals and iron contamination depressed the flotation primarily in fine particles smaller than 33 ¦m, and clay minerals played a dominant role. Although flotation of coarser particles greater than 33 ¦m was less affected by clay minerals and iron contamination, coarser grinding to increase P80 was not an effective way to improve copper and gold flotation for the high-clay ore. This study suggests that to improve copper and gold flotation from clay ores, clay dispersion in conjunction with the minimisation of iron contamination may be required.CITATION:Wei, R, Peng, Y and Seaman, D, 2013. The effect of grinding media on copper and gold flotation in the presence of clay minerals, in Proceedings World Gold 2013 , pp 283-288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By P Crittenden

Thiess Pty LtdÆs Australian Mining business unit used 7.6 PJ of energy in the 2007/2008 financial year. This represented more than 85 per cent of Thiess Pty LtdÆs total energy use and therefore meant that the Australian Mining business unit is required to conduct energy efficiency assessments and report publicly on the outcomes by December 2008 under the Federal GovernmentÆs Energy Efficiency Opportunities (EEO) Act. Thiess Pty Ltd has a policy commitment to sustainable development throughout its operations. This includes minimisation of its carbon footprint and the Australian Mining business unit has a strong focus on efficiency in all of its operations. It approached the energy efficiency assessment as an opportunity to further improve and build on its energy efficiency and greenhouse gas reduction focus in the business. As a mine contractor, Thiess faced a number of challenges in designing an assessment process that would be both effective and efficient to deliver. For example, unlike most other companies involved in the Energy Efficiency Opportunities program, the energy use associated with the Australian Mining business unit is not fixed to any single geographic location in Australia. Mining vehicles are moved from site to site according to the specific requirements of mine owners and the timing associated with the commencement and completion of contracts. Thiess departed from a traditional æsite by siteÆ based assessment and designed a ærepresentative assessmentÆ approach that involved detailed investigation of data across all sites and a focused assessment on a single site.Data and analysis was an essential part of the assessment and indicators at company, mine and site level were essential in identifying opportunities and tracking progress. Forty-six potential energy saving opportunities were identified and four of these are currently being implemented. The projects being implemented are: payload management, automating mobile lighting equipment, plant idle time management, and turbo idle downtime. The potential savings from the four major projects that have been identified are approximately 150 800 GJ/annum, equivalent to 10 600 tonnes of CO2-e/annum with a simple payback period of less than two years. Beyond the fuel savings however, there are a number of other benefits from the assessment, including operational efficiency, reduced maintenance costs and even a potential reduction in the number of vehicles required to complete the work. The EEO assessment has significantly increased the importance and urgency of energy efficiency and facilitated the sharing of good practice across all Thiess operations. Not only have four projects been adopted for immediate implementation but a further pipeline of projects is available for future possible implementation. This case study describes: how Thiess conducted its assessment including the use of energy data and indicators, the opportunities identified that are currently being implemented, and the lessons learnt and how other organisations can use these to improve their approach to energy efficiency assessments. This case study is a more comprehensive version of a case study developed for the Commonwealth Department of Resources, Energy and Tourism. The assessment results reported in this case study are drawn from the Thiess Energy Efficiency Opportunities Report 2008.

Jan 1, 2009

By R P. Varden

This paper looks at the design of the Bentayga raisebore with subsequent back analysis using a LiDAR survey. A search for LiDAR raisebore assessment publications shows little work has been done on this subject. The paper examines the empirical design and RS2 modelling assessment with the bored condition. The high resolution of the LiDAR enabled mapping of weak structures that were located on the geotechnical investigation hole the orientations of which could not be determined. In addition, the scan showed were water ingress was occurring, potential stress overbreak and structural controls on stability. The LiDAR results were able to confirm no additional support work such as a shotcrete liner is necessary. The LiDAR results have been analysed in one metre increments as volume of overbreak against the empirical stability criteria (McCracken & Stacey 1989). The future use of LiDAR mapping over a range of rock mass conditions will provide quantification of the established empirical assessment improving its reliability. It is also a useful and accurate tool to monitor long term stability of a raisebore due to stress change or ore pass due to wear.

Mar 15, 2021

By C J. Greet, S Jacques

In most instances, the application of high-chrome grinding media results in an increase in the recovery of the valuable mineral(s). The authors have published data from a number of plant-based case studies, which indicate that it is not unreasonable to expect a recovery increase in the vicinity of 1.5 to 2.0 per cent for a copper ore. It is of interest to understand where the increase in recovery is coming from. That is, is the additional copper recovery the result of improved fine particle flotation or is it due to an improvement across all size fractions?This paper aims to answer this question. Laboratory flotation tests were completed using forged steel and a high-chrome alloy on a volcanogenic massive sulfide copper ore. The unsized data indicated that the application of high-chrome grinding media to this ore resulted in an improvement in both copper recovery and copper concentrate grade. A detailed kinetic analysis of both the copper sulfide and gangue minerals was completed that clearly shows that the change to a more inert grinding media produced significant increases in the flotation rate constants (both fast and slow) across all size fractions. It is also possible to observe that the change in pulp chemistry has resulted in a decrease in the flotation kinetics of the -20 micron pyrite, while the coarse pyrite recoveries have increased, presumably because of an increase in the flotation of the chalcopyrite/pyrite composite particles.CITATION:Greet, C J, Jacques, S and Kinal, J, 2014. Recovery-by-size kinetic analysis to determine where metallurgical improvements occur when converting to high-chrome grinding media, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M Hernan

Bendigo Mining Limited has established a modern underground gold mine and processing plant at Bendigo in central Victoria. The Bendigo goldfield produced around 22 000 000 oz of gold between 1851 and 1954. Approximately 4 000 000 oz were sourced from surface alluvial workings with the remaining 18 000 000 oz won from underground quartz reefs. The modern mine is accessed via the Swan Decline, which commences at the Kangaroo Flat site on the southern outskirts of Bendigo and progresses in a north easterly direction between the Deborah and Sheepshead anticlines, reaching a depth of almost 1000 m below the City of Bendigo. Development of this decline commenced in 1998. Since that time 20 km of underground development has been completed. Exploration drilling, on-reef development and bulk sampling carried out between 1999 and 2005 resulted in the estimation of a Probable Ore Reserve of 700 000 tonnes at 9.0 g/t gold for 207 000 oz of gold. These Ore Reserves were contained within four reefs located on the Deborah and Sheepshead anticlines. Reef mining commenced in late 2005 from the Shywolup and Greater Garrard reefs. Material mined was stockpiled on the surface in preparation for commissioning of the process plant which commenced in mid 2006. Mining and processing were carried out between August 2006 and May 2007 during which time 176 000 tonnes were processed at an average grade of 5.4 g/t gold to produce 26 735 oz of gold. Plant feed was sourced from four reefs. This paper discusses some of the issues which were encountered with the definition and mining of these geologically variable and nuggetty reefs. This paper covers exploration techniques, grade estimation, mine geological control, mining methods, geotechnical issues and reconciliations. It will also discuss some of the lessons learnt and how these will be applied to future Mineral Resource and Ore Reserve estimation, as well as underground operations.

Jan 1, 2008

By H Esterhuizen

The Ernest Henry Mine (EHM) in Queensland, Australia is a Sub-level Caving operation that started production below the previously mined open pit at a depth of 535m. Current Production mining has progressed to a depth of 730m, with planned production mining to extend down to at least 1000m below surface. The inclined nature and geometry of the orebody combined with geological structures provides for challenging mining conditions. Over several years, Ernest Henry Mine has introduced measures to improve outcomes based on observations, monitoring and data analysis. As mining progresses deeper, EHM will continue to proactively take steps to ensure future outcomes are anticipated and mining can continue safely and uninterrupted. The focus of this paper is on the changes in seismic- and stress-driven behaviour of the rockmass experienced at EHM, the ground control measures implemented, and the anticipated future conditions and controls required. CITATION:Esterhuizen, H, 2018. The evolution of seismicity and ground control measures at Ernest Henry Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 20–41 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By E McLean

The decision making check-list and hierarchy of information for process and plant design is generally wide-ranging and complex. The nature of grades, mineralisation and ore types in an ore body, its mine development sequence, and the body of results from metallurgical and physical test work present complex and competing influences on flowsheet development, values for design, equipment selection, plant efficiencies and operating strategy. The challenge is how to manage all these variables, to understand their impacts on performance, and how best to provide a cost-effective plant design and robust process that meets daily/weekly/monthly operating objectives. Throughput, production and grade or product specifications need to be met. The ore body is not average; its range of metallurgical and physical characteristics may be moderately to highly variable. This paper assesses some of the key competing influences and conflicting issues in design and equipment selection, and their effect on production and performance expectations.

Aug 8, 2011

By Robertson AC

Studies by Tennent, Isokangas Pty Ltd (TIP) have indicated that underground quarrying of backfill may be a cost competitive option for providing backfill for specialised situations in underground mining. Situations where suitable bulk fill material may not be available on the surface, and where the total cost of setting up a fill distribution system are prohibitive, could favour the mining of fill material underground adjacent to the stopes being mined. Considerations include environmental impact, scheduling, surface constraints and total costs. The examples quoted in this paper, and the case studies are based on the authors' personal observations and experience.

Jan 1, 1998

By C Hedemann, N Silveste, H Davis, C J. Moran

For nearly two decades water scientists have been debating the need to use appropriate models for the questions being asked and the data available. This paper puts forward a rationale for a hierarchical framework for water balance modelling as it applies to mine sites. The hierarchy is based on the complexity of models and their data requirements. Scientific models are the most complex and require the most data; next is engineering models, then systems models and the simplest representations are given by conceptual models. A position is put forward that systems models have a range of uses that the others do not provide. A systems model, called SiteMiser, is described and its calibration illustrated. The model is applied to seven coal mines from the Northern Bowen Basin in Central Queensland. Currently, there is little relationship between total water use and coal production. This relationship is not any stronger when fresh (raw) water is compared to reused water. Leading practice water use levels are simulated for all sites. The simulation results demonstrate that there is considerable opportunity to reduce water consumption and, in particular, to import less fresh (raw) water to the sites.

Jan 1, 2006

By G R. Ballantyne, M S. Powell

A comprehensive Australia-wide survey of comminution energy consumption at copper and gold mines was presented by the authors at the 11th AusIMM Mill Operators’ Conference 2012. The database has been extended to include major overseas mines and used to benchmark comminution energy consumption across the industry. The mines included in this study now represent 15 and 24 per cent of the total global gold and copper production respectively, and almost all Australian production. The comminution energy intensity per unit of saleable metal has been presented in a graphical form similar to a cost curve used in economics. The graphical method has been developed to assess the competitive advantage that can be achieved by reducing comminution energy intensity.This benchmarking tool has been applied to three published case studies to assess its applicability. The first case study indicated that a large reduction in size-specific energy (kWh/t -75 µm) was achievable by converting standard semi-autogenous and ball mill circuits to include high pressure grinding roll and stirred mills. The second case study investigated the metal-specific energy reduction historically achieved by Bougainville with the addition of a preconcentration screening plant. The final case study was conducted by Barrick Gold Corporation and involved incremental efficiency upgrades at three of its gold mines: Cortez, Cowal and Mara North. The application of the benchmarking tool to each of these case studies successfully demonstrated the scale and competitive advantage that was achieved by reducing energy intensity.CITATION:Ballantyne, G R and Powell, M S, 2014. Benchmarking comminution energy consumption for improved efficiency, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By R Wedmaier

Henty Gold Mine is an underground operation producing 100 000 ounces of gold per annum. The original mining method used was flatbacking with paste fill. However, a non-entry method û uphole benching û was introduced in 1998 to recover the deteriorating crown pillars. Initial challenges were encountered, including poor drilling accuracy, difficulty in charging holes and poor rise performance. These challenges were overcome by a Continuous Improvement Team, consisting of mining engineers, supervisors and miners. Following this, the Team implemented further changes aimed at reducing ore loss and dilution. A second area addressed by the Team was development blasting, where innovative detonator technology known as the ExelTM DevelDetTM was introduced and rapidly accepted by the operators. Continued use of the ExelTM DevelDetTM resulted in a number of benefits, such as easier bogging, less perimeter damage, faster charging and hook-up and decreased wastage. Finally, improvements were made in the area of explosive handling, where competency-based training of operators was conducted and manual handling of ANFO has been significantly reduced by the introduction of the MiniMoverTM into the underground magazine.

Jan 1, 2001

By H Ishikawa, H Zhou, M Spagnolo, R Halomoan, S Palaniandy

The Karara Mine concentrator commenced operation in November 2012 to produce high-grade magnetite concentrate. The circuit consists of three stages of comminution plus magnetic separation at each stage for early gangue rejection. High-Pressure Grinding Rolls (HPGRs) are used for fine crushing, followed by ball mills and TowerMills in secondary and fine grinding duties respectively. In recent times, the plant throughput rate has had to exceed design by 18% to maintain the targeted concentrate productivity. Meanwhile, the ore hardness has increased by 25% to 15 kWh/t, leading to changes in the circuit operation and design. These changes led to coarser and harder feed to the TowerMill circuit that affects the subsequent separation processes. Nippon Eirich (the TowerMill manufacturer) has partnered with Karara Mining Limited (Karara) to optimise the TowerMill circuit operation to achieve a circuit product with an 80% passing (P80) of 35 µm. Several activities, including a TowerMill circuit audit and performance evaluation, multi-component analysis, modelling and simulation, were carried out as part of the optimisation exercise. The circuit audit results revealed that the TowerMill circuit feed size F80 had increased and ranged from 67–75 µm. The circuit product P80 ranged between 42–55 µm. The average circuit specific energy was 3.4 kWh/t. Moreover, the differences in density between magnetite and gangue minerals had affected the hydrocyclone performance where the efficiency curve exhibits coarse end deflection indicating that low-density coarse material was bypassing to the overflow stream. A multi-component analysis was carried out to further investigate the coarse end deflection of the hydrocyclone efficiency curve. The analysis showed that the magnetite and gangue minerals had different cut sizes of 32 and 64 µm respectively. Furthermore, 33% of the magnetite (below 35 µm) was being recycled back to the mill due to the density effect. Based on these findings, several recommendations for process improvement were identified and implemented including:• converting to a bottom feeding configuration to improve the grinding efficiency in the mill• additional grinding power in the fine grinding duty to compensate for the increase in plant throughput and ore hardness• improved classification efficiency by converting to smaller size hydrocyclones. Simulation studies carried out to evaluate the impact of these implementations had indicated that a P80 close to 35 µm with a steeper size distribution could be achieved by using the bottom feed configuration with additional grinding power. The TowerMill circuit was converted to bottom feed configuration and the performance was evaluated. The operating work index, size specific energy and circulating load were 30% lower than the top feed configuration, indicating that the bottom feed configuration had a higher grinding efficiency. This paper discusses the outcome of the circuit audit, multicomponent analysis, circuit simulations, improvement strategies and quantification of the improvements. CITATION:Palaniandy, S, Spagnolo, M, Halomoan, R, Zhou, H and Ishikawa, H, 2017. Fine grinding circuit process improvement at the Karara mine concentrator, in Proceedings MetPlant 2017, pp 101–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By X Tian, J Forster, A Olmsted, E R. Bobicki, M Goldbaum, D Boucher, C A. Pickles

As the global demand for metal values expands, it becomes increasingly important to create more sustainable mining operations. Consequently, considerable research and technology development is required to produce processes which are both more energy efficient and have a minimal environmental impact. One potential technology is the utilisation of microwave pre-treatment to reduce the energy requirements in comminution. Microwaves can preferentially heat the valuable mineral phases in an ore and the resulting differential thermal expansion leads to the formation of microfractures along the grain boundaries. As a result of the preferential heating, ore competency is reduced, mineral liberation is enhanced, a coarser grind size can be employed, and plant throughput can be increased. Furthermore, microwave pre-treatment can be combined with advanced ore sorting, to decrease the quantity of gangue material processed downstream and hence reduce tailings production. Previous studies on the microwave treatment of ores over the last 30 years have mainly been limited to low power bench-scale studies and there is a paucity of information on pilot and/or commercial scale studies. In the present research, the microwave heating behaviours of over 40 ores have been studied at the bench-scale. These results were used to generate a database, from which a unique classification system was developed. This system was used to rank the amenability of any given ore for microwave pre-treatment. This knowledge can be employed to predict the performance of the ores in the high-power pilot scale tests and thus can be used as a pre-screening tool. The effects of high-power microwave pre-treatment on grindability and liberation were reported. Additionally, the ore sorting potential was evaluated using a combination of X-ray transmission (XRT) and microwave infrared (MW/IR).

Aug 24, 2022

By N Ganjian, A Delavar, F Rashidi Nejad

Iran is one of the most seismically active countries in the world, being crossed by several major fault lines that cover at least 90 per cent of the country. As a result, earthquakes in Iran occur often and are destructive. So, it is important to consider the seismic stability and reliability of all structures including tailings dams.In this study, the tailings dam stability of the Sangan Iron Ore Mine in Khorasan Razavi, Iran is considered for the case study. The tailings storage facilities of the mine have three cells with the capacity of 45 million cubic metres. The first cell, which has three stages of dam raising, has been recently brought into operation. This cell has a downstream-raised retaining embankment. As the risk of seismicity in this area is high, seismic response of this dam was evaluated by numerical methods. To do this, appropriate models were developed for materials used in foundation and body of the embankment. Then for seismic stability analysis, Tabas (Iran – 1978) and Chi-Chi (Taiwan – 1999) earthquake acceleration simulations were applied.The results of this study indicated that the upstream portion of Stage 3 of the dam and dam crest did not experience significant horizontal displacements during earthquake period, but the downstream portion of Stage 3 of the dam showed a maximum horizontal displacement of 60 cm at the third stage of dam raising. This is three times more than what was estimated by the designer. Also, the maximum vertical displacement resulting from simulation of the Tabas earthquake was 35 cm. The results of dam response to Tabas and Chi-Chi earthquakes indicate that displacement, shear stress and pore pressure by the Tabas earthquake were higher than the case of Chi-Chi earthquake. The higher energy of Tabas earthquake and the higher frequency near to the natural frequency of Tabas earthquake could be the reasons of this difference. The results of this case study confirm that if the studied tailings dam impacted by an earthquake of a similar magnitude to Tabas, the dam will be seismically stable and the developed strains will not be significant.CITATION:Delavar, A, Rashidi Nejad, F and Ganjian, N, 2015. Seismic stability analysis of Sangan Iron Mine Project tailings dam, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By F Phillips, E Deucker, J Kato

It is challenging to determine the optimal mining strategy to maximise value when a mine plan includes mineralised material which does not meet the full cost of mining but has value exceeding the variable cost of mining (‘marginal material’). Mining too much marginal material dilutes the operation’s head grade and undermines profitability. Conversely, leaving too much metal behind fails to achieve the full value of the endowment. Finding the balance between the two will maximise value delivered from the asset. This dilemma has traditionally been approached by calculating a suite of cut-off grades to define the grade of material that meets economic targets for an orebody (or zone within) and should therefore be included in the mine plan. A problem with this approach is that individual mining blocks within the zone have different costs, value and confidence levels, with each having economic co-dependencies between them. Blocks of identical grade but different mining contexts will have distinctly different economic outcomes. For example: • a block may be a low-grade increment or shell around a higher-grade stope; • a block may be available to be mined when there is spare mining capacity; or • a block may defer access to significantly higher cash flow material. Each of these circumstances would result in different value from the blocks if included as part of the mine plan. Cut-off grades calculated as averages over zones of material, or in isolation from schedule-based information, are missing the entire mining context that determines the ultimate economic outcome of making a mining decision. There are tools and techniques available to address this for open pit mining, however underground mining has different nuances. There are more intricate economic and physical dependencies between potential ore blocks, and importantly, the decision to leave material in situ can be made at any time. The case study in this paper explores a new methodology for underground mining, targeted towards strategic planning applications. It examines whether the economic logic usually applied via cut-off calculations can be implemented in the schedule so that optimal economic decisions can be made on a block-by-block basis, taking into account the mining context of the block, with the objective to maximise asset value. The results of the case study scenarios in Table 1 demonstrate the magnitude of the potential improvement in NPV that can be attained by a block by block valuation approach

Mar 15, 2021

By S McGregor, J Sharp, I Entezari, T Boulter

The piezocone penetration test (CPTu) is one of the primary screening tools used by the mining industry to evaluate whether tailings are susceptible to liquefaction (static or cyclic). Liquefaction analysis using the CPTu is influenced by the fines content of the soil, and most CPT screening tools empirically use the behaviour type index (Ic) to correct for fines. The issue with this approach is that such empirical relationships have been developed using data collected from natural soils and their applicability to different tailings deposits needs to be studied. In this paper, we explore the use of machine learning to develop a site-specific model to estimate fines content of tailings using gamma piezocone penetration testing (GCPTu) measurements. The results are then compared to the fines content derived from the soil behavior type index (Ic) proposed by Robertson and Wride (1998). A dataset of paired GCPTu and laboratory results were compiled and a support vector machine (SVM) algorithm was employed to calibrate a model to estimate tailings fines content from in-situ GCPTu data. We calibrated GCPTu data to geotechnical 75 μm fines content measured in the laboratory. The geotechnical fines content is the fines content as a percentage of solids. The development dataset was comprised of paired GCPTu-laboratory results collected in 2009-2019 from a mining area with predominately clay mineral and quartz sand tailings. Results show that the developed model predicts the geotechnical 75 μm fines content of the studied deposits with 7.8% error. The Ic based method estimates the fines content with 31% error. Evidently, the Ic method is not applicable to the studied tailings deposits. It is appreciated that many tailings fines do not contain clay, and that the success on this program may not be repeatable everywhere. However, the authors wish to point out that the application of site-specific machine learning algorithms may be used to significantly improve empirical geotechnical parameters.

Jul 1, 2021

By S Shafiee, N Abbate

The evaluation of mining projects requires a methodology that will give flexibility and manage the existing uncertainty within the projects. The discount cash flow (DCF) and other traditional evaluation approaches, which are widely used in evaluating a significant number of mining projects, have simply assumed that the main variables remain constant in their evaluation; elements such as discounted rate, mine life, operating cost and production rate. The DCF ignores managementÆs flexibility to adapt and reforecast and revise decisions. Real options valuation (ROV) is one of the modern evaluation methodologies that provide a tool to adapt and revise mining projects under uncertainty and future variables movements. ROV brings more variables into the evaluation model compared to DCF and assumes them as uncertain and dependent. Finally, ROV provides a range of solutions that can assist in managing this flexibility.This paper endeavours to compare ROV and DCF for mining projects comprehensively and applies these two techniques in the model. The paper shows that ROV will be inclusive of extra value in mining projects due to variables not allowed for, or even ignored, when the DCF model alone is used. One of the significant advantages of the ROV method is being able to evaluate mining projects under different scenarios from the inception of the projects. Furthermore, ROV gives the ability to evaluate the mining project while allowing for abandonment, temporary suspension, or expanding the mining project. In other words, the ROV evaluation process creates an analytical environment, which allows for optimisation of the mining plan within the mining project, as well as the ability to change the capital structure dependant on existing circumstances over the life of the project. The ROV is a new evaluation method that can add value in mining project analysis and offers opportunities to amplify gains, or to mitigate losses. This paper also discusses some of the reluctance to use ROV instead of DCF in current project evaluation.CITATION:Shafiee, S and Abbate, N, 2012. Now, this is the time for mining companies to choose - Real option valuation or discount cash flow, in Proceedings Project Evaluation 2012 , pp 225-234 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By B Wu, B W. Lei, B J. Duan

When a coalmine fire occurs, it is crucial to judge the developing trends inside the fire area by analysing the changes of gas concentration in order to formulate the proper rescue measures. At present, few researchers have focused on the relationship between the changing trend of gas product and basic characteristics of fire in the coal fire extinguishing process. To study the relationship of basic characteristics of coalmine fire during the extinguishing process, an experimental platform for coal combustion in a confined space was built, and gas production, flame image and coal temperature during the extinguishing process were monitored and analysed by an online continuous gas analysis instrument, camera and thermocouple. Research shows that during the burning phase of the coal sample in the confined space, the flame zone decreases gradually due to insufficient gas supply. The size of the flame zone fluctuates and shares a positive correlation with CO concentration, while sharing a negative correlation with O2 and CO2 concentrations. Then, in the extinguishing phase, the increasing rate of CO2 concentration and the decreasing rate of O2 concentration both decrease gradually, but CO concentration would rise for a period before it eventually decreases. Coal temperature continues to rise in the open flame stage and does not go down until the flame is extinguished.CITATION:Lei, B W, Wu, B and Duan, B J, 2015. Experimental study on extinguishing characteristics of coal fire in confined space, in Proceedings The Australian Mine Ventilation Conference, pp 279–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By G Tsatouhas, R Newell, K Y. Wong

A sulfide ion selective electrode was used to control sulfidiser addition in the flotation testing of a synthetic and a naturally occurring ore containing malachite in order to compare the behaviour of sodium sulfide and calcium polysulfide. Both slug and controlled potential sulfidisation methods of addition were used. Under defined optimum CPS conditions, calcium polysulfide was a more effective sulfidising agent than sodium sulfide on the basis of both capital and operating costs. Surface and solution studies were used to compare the mechanism of each sulfidiser. For calcium polysulfide, XPS showed that polysulfide ions are adsorbed, whereas for sodium sulfide it is the hydrosulfide ions that are adsorbed on the mineral surface. For calcium polysulfide, the CuSx layer was believed to form on the malachite surface, which promoted the flotation of the malachite, by xanthate. Studies of surface morphology of the sulfidised malachite showed that a fairly uniform sulfidised layer is formed with both reagents. The use of sodium sulfide resulted in a thinner initial sulfidised layer compared to polysulfide at equivalent initial sulfur concentration.

Jan 1, 2005