Search Documents

By H Turrer, M Badawi, R Belissont, Y Foucaud, E Kleiderer, L Southavy, J Mesquita, Y Basselin

The Mont Reed iron ore deposit, owned by ArcelorMittal, is situated approximately 140 km southwest of the Mont-Wright mine in the southern region of the Labrador Trough, Canada. Acquired by Québec Cartier Mining (QCM) in the 1960s, the Mont Reed mining property has remained unexploited due to the complex nature of the ore in the area. However, during the last years ArcelorMittal’s R&D team has been dedicated to developing a process to beneficiate the Mont Reed ore and produce high-quality pellet feed suitable for direct reduction furnaces. Extensive research revealed that achieving a good liberation degree of particles required grinding the material below 75 μm (P80 of 53 μm). To find the most effective technology for this task, a detailed comparison between ball mill and vertical stirred mill grinding was conducted. Both grinding technologies underwent detailed testing in bench-scale experiments. The ground products were comprehensively characterised, including size distribution analysis and chemical analysis per size fraction. Additionally, liberation analysis was performed using an automated scanning electron microscope (SEM). To determine the grinding specific energy, a method previously developed at Samarco (Brazil) for fine grinding of iron ores was employed. Furthermore, magnetic separation and flotation tests were conducted on the ground products. After a thorough evaluation of all the results, it was observed that both ball mill and vertical stirred mill grinding produced samples with similar physical characteristics. However, the vertical mill demonstrated higher efficiency in grinding the material. To conclude the study, an economic evaluation was conducted for both options considering various factors. Overall, ArcelorMittal’s R&D team’s dedicated efforts have brought them closer to unlocking the potential of the Mont Reed ore deposit and paving the way for its future utilisation to the production of high-quality pellet feed.

Sep 18, 2023

By Z Li, A Fleming, S Webster, L Snyman

Northparkes Mines is developing the E26 Lift 1 North block cave mine, which is adjoined to the existing E26 cave. This paper presents the challenges and methods used to design the ground support system during the feasibility study. Calibrated numerical simulations were conducted to forecast the levels of rock mass damage and to assist the ground support design. Generally, low to moderate rock mass damage is forecast on the extraction and undercut levels. However, poor ground conditions are expected in sheared and preconditioned zones adjacent the existing E26 cave. This will result in difficult ground conditions during development, undercutting and drawbell establishment. Empirical assessments were conducted to make sure the ground support system is able to handle both the static and dynamic load demand, and to accommodate the deformation values. A safety factor of 1.5 was used for the designs to cover the unknown rock mass conditions and potential for larger seismic events. Learnings from the E26 Lift 1 and SLC, also mining against the E26 cave, are incorporated into the design. Fibrecrete, mesh and resin bolts / mechanical anchors are the primary ground support system used, and cable bolts for intersections with a span of more than 6 m. Following undercutting and during the operating life of the mine, secondary ground support and rehabilitation will be required.

Mar 15, 2021

By Beeby C. j, Fernando W. J, Ming M. Q I, Guang Li Xi

Removal of moisture in steam-fluidized, mainly steam-heated, fluidized beds makes possible significant energy savings over conventional forms of large-scale drying. The systens are described and their applications to brown coal and alumina hydrate are reviewed. In application to brown coal the use of the system to permit meeting diurnal variation in power station output, and the use of triple-effect drying to minimise coal usage and to avoid the necessity of recovering in the turbines the energy in the steam from the last dryer are discussed. To facilitate the rapid adoption of the systems proposed, studies are being made of heat-transfer to dried coal, of moisture equilibrium in pressurized and vacuum systems, of tapered beds as a means of reducing carrier steam and permitting wider size variation, and of the use of carrier solids for drying lump materials.

Jan 1, 1989

By B E. Hall, J Poniewierski, A J. Hills

Following a review of life-of-asset work at MMG’s Rosebery mine in which a proposal to increase production from 0.8 Mt/a to 1.2 Mt/a was mooted, questions were raised as to the seemingly arbitrary reasoning for the production increase. They included: Did the proposal actually add value? Was the production rate from the mine sustainable? Was it the best identifiable value-adding configuration?A multiple scenario analysis study commenced to model how various cut-off grade values against mill throughput, along with associated capital expenditure, would impact on the potential value of the operation. This was carried out utilising the ‘hill of value’ approach promoted by AMC Consultants.The traditional approach to these studies uses a constant cut-off value (NSR – net smelter return) for the whole mine analysis. This was thought to potentially introduce a large amount of variability to the model as different ore types were thought to have different processing costs and different underground lenses were thought to have different mining costs. With the aim of developing a consistent value measure that would be comparable between the lenses, an alternative measure was suggested for all ore block values in this model, irrespective of lens location.The new measure used was a mine variable value (MVV). This allowed for the variable factors of final metal concentrate production to be removed from the ore value. From a mining point this was the haulage distance from ore source to run-of-mine (ROM). For the mill it was the amount of reagents required, varying based on grade together with the amount of power required for crushing, grinding and tailings handling.From the initial run of the model, preliminary results lead to a conclusion of increased value being gained by either increasing cut-off grade or increased mill throughput rate. The validity of the result was tested using alternative price scenarios, which although changed the absolute value achieved did not significantly change the identified value-adding strategies. The realisation of these value increases identified are however contingent on higher sustainable development rates being able to be achieved mine-wide, higher backfilling rates being able to be achieved and overcoming recognised ventilation constraints. Further detailed studies are being put in place to identify the practicality of overcoming these recognised constraints and achieving the higher-value strategies identified.The ongoing objective of the hill of value model built is to keep the model alive as a life-of-asset planning tool and to continue refining the foundation data, such that various mining strategies can be analysed with increased confidence.CITATION:Hills, A J, Hall, B E and Poniewierski, J, 2014. Mining scenario analysis and mine variable value, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 111–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By J Joy, A Bye, G V. Kizil

This paper demonstrates an application of a recently developed Risk-Cost-Benefit (RCB) Framework to environmental risk management in the mining industry. The environmental application of the RCB Framework as part of an ACARP project (Kizil, Bye and Joy, 2012) involved a thorough selection process with site visits and in-depth discussions with the case study siteÆs environmental management team. Under their guidance, the highest risk of environmental impact at the case study site was identified as æroad subsidenceÆ at the time when the project work was undertaken. This paper presents the unique application of the RCB Framework to examine the risk of mining-induced subsidence and its impact on one of AustraliaÆs busiest highways, with a traffic volume of 38 000 vehicles per day (NSW RTA AADT, 2008). The RCB Framework was employed to assess the optimum group of controls for road subsidence risk management to ensure highway availability while mining occurs. Whilst this paper focuses on road subsidence, the methodology employed can be directly applied to other environmental concerns including preparation for mine closure, rehabilitation planning and waste management. The RCB Framework incorporates mathematical modules which were developed to enable complex yet tightly integrated RCB calculations. The process integrates the risk-control effectiveness assessment to determine that the selected safety initiative is financially beneficial to the mine site and company. This concept has been applied to a number of high-risk mining areas targeting safety, productivity and environmental issues. This paper introduces the five-staged RCB Framework, incorporating the RCB tools RCBGEN (Risk-Cost-Benefit Generator) and RCEMETHOD (Risk-Control-Effectiveness Method), and demonstrates its practical application to the risk management of a road subsidence case study. The case study looks at potential pavement damages, in particular, the occurrence of pavement stepping on the surface of the highway as a result of vertical subsidence. This type of road damage was previously experienced at another major inter-city route while underground mining occurred in the region where the case study site is located. The RCB Framework has been successfully applied to the analysis of the road subsidence case study and determined the risk reduction and financial benefits of implementing a range of risk-controls. User-friendly RCB Charts to provide an aid for decision-making were produced. The value of using the RCB charts to achieve balance between risk, cost and productivity in the decision-making process for risk management has been explained. The case study determined that pavement slots and fibre-optic cable monitoring were relatively low-cost and effective controls applied in the mining industry for the first time at a global level.This paper supports the industryÆs ongoing efforts to manage risk to ALARP (as low as reasonably practicable) and achieve æzero harmÆ by providing a new Framework to more effectively establish the adequacy of controls.CITATION:Kizil, G V, Bye, A and Joy, J, 2012. Application of risk-cost-benefit analysis to highway subsidence due to mining, in Proceedings Life-of-Mine 2012 , pp 197-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By G M. Tranell, M Tangstad

The CO2 footprints in the production of Mn-ferroalloys and silicon/ferrosilicon are correlated with the fossil carbon consumption. The CO2 emissions may be reduced in the Mn-ferroalloy process by increasing the degree of prereduction and reduction of carbonate materials, while the silicon/ferrosilicon process is optimised based on silicon yield. By changing the fossil reductant into biogenic reductants, the global warming potential will be decreased even more. Even if the reductants are biogenic reductants, there will still be a global warming potential (GWP) in eg the electrode consumption and the CH4 emissions in the charcoal production. To reduce the use of fossil reductants there are also more disruptive technologies like the use of H2 that at least for the silicon production is on a very low technology readiness level (TRL). Using metallothermic processes will reduce the use of carbon but requires carbon neutral metal reductants. Electrowinning can have low CO2 emissions, and the electrowinning of pure Mn is a technology of high TRL. Salt and oxide electrolysis is under investigation for both Mn and Si production however the research is still on a low TRL. The use of CCS/CCU (carbon capture storage/utilisation) is a part of obtaining carbon neutral processes. Last, the energy mix used for these energy demanding processes is discussed.

Aug 21, 2024

By J Jardine

An improved ground support method for development intersections, wide spans and stope brows was implemented at Kanmantoo mine. The method uses a jumbo to simultaneously drill and install self-drilling anchors (SDAs) to depths from 4.5 m to 7.0 m. Resin is subsequently pumped into each SDA using a specially designed integrated tool carrier basket, with plating occurring within 10 mins due to rapid resin cure. This methodology means that SDAs can be installed rapidly due to reduced process steps and wait times with reduced hazards to personnel. Cablebolts are used extensively in underground mines to reinforce the ground in wide spans, such as at intersections and stope brows. The flexible cablebolt tendon allows for a long, continuous and high-capacity reinforcing element to be inserted into the rock. A common cablebolt installation practice at Australian underground mines that do not utilise a mechanised cable bolter, is for cablebolt holes to be drilled by a jumbo or longhole rig, hand installation and grouting by a service crew, then plate tensioning following a grout curing wait time of typically 12 to 24 hours. This process involves multiple separate labour-intensive work processes and results in reduced availability of priority headings. This paper discusses the development history of vertical SDA use in wide spans at Kanmantoo mine. The installation process is fully described, including aspects such as reliable in-hole coupling of SDAs, resin selection and pumping aspects. A cost benefit assessment, and a case for ground stability are presented to compare cablebolt use to SDAs in development intersections.

Mar 29, 2023

The continuous casting of zinc alloys has been of fundamental importance for many years in the production of a number of products, including sheet for architectural applications, battery cans for dry cells and wire for metallising. The intrinsic benefits of continuous casting, including efficiency and high tonnage capability, uniformity of metallurgical structure and properties, and absence of voids and other defects, have contributed to the success of these products. Less well known, but of growing importance, is the more recent application of continuous casting technology to the production of zinc alloy bar stock products, including bearing stock, machining bar stock, forging stock and cathodic protection anodes. A wide range of zinc alloys are now continuously cast in a variety of cross sectional shapes and sizes to suit the diverse characteristics of these products. Of particular significance are the introduction of hollow zinc-aluminum bearing stock, and the availability of zinc alloy machining bar stock for hydraulic applications and for producing prototypes of zinc alloy pressure die castings. In addition to the traditional benefits, continuous casting provides special properties which are important in the application of these bar stock products. The list of successful applications of continuously cast zinc alloy bar stock is growing rapidly, and the market potential for resultant new zinc applications appears to be significant.

Jan 1, 1993

By Green A. D M

The establishment of the Imperial Smelting Furnace at Sulphide Coporation Pty. Limited for the smelting of zinc and lead made it necessary to design and install sintering capacity to produce approximately 500 t.p.d. of zinc-lead sinter. The updraught sintering process installed is a recent development and the plant was designed with adequate flexibility and equipment to enable operating staff to investigate the process and achieve maximum production under optimum operating conditions.Sulphur dioxide gases from the sinter machine are passed to a contact acid plant for the manufacture of sulphuric acid.

Jan 1, 1964

By J Wen, P Hou, W Yu, M Hu, Z Jiang, C Bai

Vanadium titano-magnetite (VTM) is one of the important iron ore resources in the world. High viscosity and low fluidity are the basic characteristics of hot metal containing vanadium and titanium during the ironmaking process. Clarifying the influencing mechanism of the melt viscosity would be a significant issue for the high efficiency smelting of VTM. In this paper, a self-developed melt viscometer based on the principle of torsional vibration theory was employed to measure the viscosity of hot metal accurately. Simultaneously, the thermodynamic calculations and some modern detection methods were also used to investigate the precipitation behaviour of high-melting-point phases in hot metal containing vanadium and titanium. The measuring results show that the viscosity of molten iron gradually increases with the increase of titanium content when the mass fraction of titanium is between 0.09 wt per cent – 0.50 wt per cent. Meanwhile, the viscosity of the hot metal was affected significantly by the vanadium content. When the vanadium mass fraction was higher than 0.30 wt per cent, the viscosity of hot metal increased sharply, which will have a serious impact on the fluidity of the hot metal. Furthermore, it was revealed by thermodynamic calculations that an increase in titanium and vanadium content would result in the precipitation of high melting point phases such as TiC, TiN, VC, and VN in the molten iron, ultimately resulting in a decrease in its fluidity. Meanwhile, it was confirmed by Scanning Electron Microscope (SEM) observation that the precipitates in the hot metal were compounds consisting of V, Ti, C, and N elements, which agrees well with the thermodynamic analysis results.

Aug 21, 2024

LIST OF CONTENTSAbstractIntroductionSelected Sections of the Broken Hill LodeLocality PlansPetrology1. Zinc Corporation Mine: DDH. 5.98, section 30, No. 26 level2. Zinc Corporation Mine: DDH. 838, section 30, No. 13 level3. Broken Hill Sonth Mine: 60 ft. cont01(r above 1170 ft. level4. Broken Hill South Mine : No. 7 shaft section, 1370 ft. levelOrigin of garnet sandstone5. Barrier Central Pty. Ltd.: DDH. tJ.93, Block 136. North Broken Hill Ltd.: Junction mine, DDH. 602, No. 10 level7. North Broken Hill Ltd.: Jnnction mine, DDH. 588, No. 11 level8. North Broken Hill Ltd.: North mine, DDH. through Southern ore body, 3370 ft. level9. North Broken Hill Ltd.: North mine, Northern ore body above 2300 ft. level(a) Southern end, section 27, 77 ft. above rails(b) Northern end, section 30, 6.9 ft. above rails(c) Miscellaneons samples, sections 27 and 28Relative time of ore depositionSericitizntionStructural significance of sericitizationGCLhnite OrthoclaseApatite GarnetManganese SilicatesAlteration of manganese silicatesRelation of zinc and lead to the silicatesZinc in manganese-bearing silicatesLead in potassium and lime silicates and apatite

Jan 1, 1959

By R Battison, R Duggan, S Esen, K Henley, P Dare-Bryan

Increased catch bench crest loss has been observed in recent years at Barrick’s Cowal Gold Mine situated in central New South Wales, Australia. A project was initiated to diagnose the cause of the crest loss, and evaluate ways to limit its effect on final walls.A range of different blast measurement techniques were utilised to evaluate the progressive damage caused to catch berms by presplit, production and trim blasts. Techniques employed included; single point vibration measurement, cross-hole seismic analysis, precision berm surveys, horizontal p-wave velocity measurements, crest loss volume calculation and water level changes between blasts.Blast measurements showed that the majority of damage to the catch berm was caused by the presplit blasts, which registered vibrations greater than 700 mm/s at 5 m behind the presplit line. As a result, considerable changes were made to the blast designs after a series of computer simulations via mechanistic blast modelling (MBM). The uncharged presplit collar was increased from 2 m to 4 m, and every second hole was left uncharged. Vibration modelling using a multiple seed wave (MSW) model was used to optimise trim blast delay timing. Burden relief was changed from 16 ms/m to 27 ms/m using one hole firing per 4 ms time window, and the initiation angle was changed from shallow to steep. These changes in the presplit loading and trim timing helped reduce catch bench crest loss by 1–2 m.Trim shots using a high strength bulk emulsion explosive were also identified as contributors to berm damage after analysis of blast monitoring and MBM modelling. The modelling study resulted in the generation of alternative blast designs to minimise the crest loss, including the use of low-density/low-velocity of detonation (VOD) bulk explosive product (Flexigel™ Advantage) in trim pattern designs. This was trialled on the Northern and Eastern pit walls to evaluate the damage to catch berms on final walls. The trials demonstrated that berm vibration was reduced significantly; fragmentation was similar (or slightly blockier) compared to the fragmentation using the old blast designs; displacement of the berm was reduced, so increased catch bench widths were attained. This paper summarises the trials, and presents a summary of the crest loss to date.CITATION:Battison, R, Esen, S, Duggan, R, Henley, K and Dare-Bryan, P, 2015. Reducing crest loss at Barrick Cowal Gold Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 189–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J M. Shekiro

In the chloride process to manufacture TiO2 pigment, feedstocks containing higher TiO2 contents (high-grade ores or HGOs) are favoured in order to minimise production of undesirable by-products. Most of today’s HGOs are produced through the smelting or reduction and leaching of ilmenite, processes which consume significant energy and/or produce large volumes of non-titanium materials that may have to be landfilled. In order to improve the economic and environmental sustainability of its TiO2 business, the DuPont Company, working with Kobe Steel Ltd, has developed an innovative process called TiRON for making HGO. Using a rotary hearth furnace, the process reduces ilmenite to a high TiO2 slag and metallic iron granules. The TiO2 slag is suitable for TiO2 pigment manufacture, and the iron is suitable for steel making. TiRON can process sand or rock ilmenite of varying compositions and particle sizes. Fossil fuel instead of electricity supplies the energy for the reduction. Dusts and off-spec materials are recycled. These process attributes, together with capital requirements estimated to be significantly lower, give TiRON substantial economic, environmental, and process flexibility advantages over conventional ilmenite upgrading processes. TiRON has been demonstrated at the semi-works scale, and preparations are being made to bring it to the pilot scale.

Oct 5, 2011

By A Späth

Active explosion barriers are used to contain and suppress a methane gas and/or coal dust explosion propagation, including localised mine fires. Early research indicated that these active explosion barriers could be used on a mechanised cutting machine, making it the only technology that could suppress an explosion during its propagation phase at the cutting face. Thereby not only adding protection during mining operations but also reducing the development of toxic gases, fatal temperature increase and fatal overpressure build-up. During their evolution over the last two decades, further advantages of Active explosion barriers were proven in mine operations in countries such as South Africa and China. Characteristics such as effectivity, efficiency, mobility and space restrictions allow these systems to be used in various locations within a mine operation, including highwall operations. This improved technology contribution to safer coal mining was recognised by mine operators, workers and regulators. The Queensland’s Recognised Standard 21 (Resources Safety and Health Queensland (RSHQ), 2021) stipulated active explosion barriers as a technology to ensure the safety within their underground coalmines. The mobility and flexible implementation of the active explosion barriers allow a feasible and practical solution for all critical locations for explosion and fire management in an underground coalmine. The conformance to the Recognised Standard can be achieved all underground coal mining operations such as Bord and Pillar, and Longwall mining. This paper describes the conformance, implementation and use of Active explosion barriers for Longwall mining and development as well as Bord and Pillar mining in Queensland’s underground coalmines.

Oct 12, 2022

By J Holdsworth, L Sutton, A Lavrinec, D Ilic

Air quality is a big topic of discussion in regional mining communities as well as urban environments situated close to port terminals handling bulk solids. Community perception of poor air quality can significantly affect the reputation of the mining operation and handling facilities. Dust monitoring for regulatory compliance relies on using a handful of accurate but very expensive sensors, usually situated at the boundary, relatively far from the activities that generate the airborne dust. These reference monitors measure dust leaving the site but dust mitigation and management on-site largely relies on operator judgement. At a fraction of the cost, small wireless solar powered units can be used to supplement reference monitors in real-time. Due to their compact nature, portability and low price, these units can be implemented on a mass scale to increase spatial resolution of dust measurements and, more importantly, in much closer proximity to both the dust generating activity and the sources of dust. This can provide valuable insights into the origins and timing of dust generation thus producing datadriven decision-making while minimising subjectivity. Similarly, light detection and ranging (LiDAR) is another supplemental technology that can be used to increase the spatial resolution of dust measurements in near real-time, however, the cost of commercial systems even exceeds that of regulatory monitors. LiDAR also presents difficulties in quantifying dust plume concentrations. This study presents learnings of implementing both technologies for dust emissions management. Several low-cost sensor units and a fast-scanning custom-built 3D LiDAR system operating at a range of 1.5 km with a resolution of 1.5 m were deployed on a surface mine to monitor dust emissions from different activities. The project explores the use of real-time sensor data to quantify LiDAR measurements in parallel with integration into mine planning. The approach can assist in prioritising dust mitigation activities thereby reducing instances of emissions exceedance and minimising water use through databased and targeted application. Demonstrated is an opportunity for a step-change in industry best practice as well as commercialisation and operationalisation of the method across different industries, including future mineral extraction.

Sep 18, 2023

By C Nyoni, T Nguyen, C R. W Seymour, G D. Dempers

Unplanned dilution directly adds cost to production from mining, milling, tailings disposal and administration. Additionally, unplanned dilution decreases the productivity, profitability and may affect the planned life of mine. Identifying and quantifying the potential for unplanned dilution allows optimisation of the mining plan and mining practices to minimise the adverse impact on productivity and the cost of production. The Dilution Rating System (DRS) has been developed to more accurately predict dilution thickness and the variable potential for dilution, from individual stopes to life of mine planning. The DRS utilises the methodology developed for the Mining Rock Mass Model (Seymour et al 2007, Jenkins et al 2009) to generate a three-dimensional dilution rating model, which is then calibrated against stoping performance. Dilution can be predicted more accurately and the parameters affecting dilution can be determined and minimised through improved mining techniques, for example blasting and ground support design. Potential high dilution areas can be identified in the planning stages of the mine and systems put in place to mitigate the risk of excessive dilution. This paper presents the methodology used to develop the DRS and then successfully predict dilution for both the hangingwall and footwall of stopes at the Gara Gold Mine. This has enabled the expected dilution to be more accurately predicted and mitigated where possible thus reducing unplanned dilution.

Mar 15, 2021

By L Jackson, A Parbhakar-Fox, N Fox

"Characterisation of sulfide minerals (eg pyrite, sphalerite) in historic tailings can assist in determining whether there are economic benefits of reprocessing such materials using modern metallurgical practices. In addition, there are associated environmental advantages if the historic tailings are actively generating acid and metalliferous drainage (AMD). At the Old Tailings Dam (OTD), Savage River, Western Tasmania, 38 Mt of pyritic tailings were deposited from 1967 to 1982; consequently it has been recognised as an AMD source. Long-term management options considered for this site have included the establishment of either a water, hard-engineered or vegetation cover. However, due to geotechnical challenges posed and the lack of success demonstrated by previous pilot studies, these strategies have not been implemented. Instead, resolving the pyrite chemistry can allow for a first-pass assessment of whether reprocessing these tailings is a feasible option as part of a long-term management strategy for this legacy site.Tailings samples (n = 144) were collected across the OTD from up to 2 m depth from five facies (A–E), and four zones (1 to 4; defined by hydrological regime and grain size). These materials were subjected to acid-base accounting (ABA) and mineralogical evaluations to determine their geoenvironmental characteristics. Following this, 26 samples were selected for in-depth laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) investigations to evaluate pyrite chemistry across different tailings facies. The results revealed enrichment of Co and Ni in these materials. Specifically, Co content was up to 3.0 wt per cent, particularly within facies C to E, and Zones 3 and 4. Cobalt is recognised as a critical metal, therefore, reprocessing should be considered as a future rehabilitation option for the OTD, pending resource definition using established codes and practices.CITATION:Parbhakar-Fox, A, Fox, N and Jackson, L, 2016. Geometallurgical Evaluations of Mine Waste – an Example from the Old Tailings Dam, Savage River, Tasmania, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 193–204 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By V Matousek, A Sellgren, R Visintainer, G McCall

A 4-component model for settling slurry pipe flow has been previously described by Wilson et al (2006) and Sellgren et al (2014) to predict pipeline friction loss (hydraulic pressure gradient) over a range of slurry compositions: from fine to coarse particle size, narrow to broad particle size distribution, and low to high solids concentration. The method applies a weighted average of established pipeline models for various settling slurry flow regimes, according to the volume fraction of solids falling within the applicable size range for each model. Further development of the model was undertaken by Visintainer et al (2017a, 2017b), based on a comprehensive set of laboratory tests in 203 mm (8 inch) and 103 mm (4 inch) pipelines, and it was also adapted to the modelling of slurry pump performance derates. However, this work was all performed with solids having a specific gravity near 2.65, as is typical for many mineral processing and dredging applications. The goal of the present work is to test the applicability of these models for settling slurries having a higher solids specific gravity, as may often be seen in the mineral processing of iron ore deposits. To that end, a test program was carried out in a 103 mm (4 inch) pipe loop using various compositions of an iron ore product having a solids specific gravity of 4.75 and containing both coarse and fine solids. By screening and flushing operations, a range of particle size distributions were created having different proportions of the coarse and fine elements. In all, 19 tests were performed with d50 particle sizes ranging from 50 μm to 3.2 mm and delivered solids concentrations from 10 per cent to 43 per cent by volume. Particle size distributions varied from very narrow to very broad, with d85/d50 ratios ranging from 1.75 to 26. Pipeline pressure gradient and pump performance data were collected and used to test the applicability of the previously developed 4- component models and to propose improvements to the models for the handling of high-density solids.

Nov 8, 2021

By D Johansson, C Yi

Blasting techniques are widely used to fragment rock masses into smaller pieces. Numerical modelling is an efficient method employed by many researchers in the blasting field. It is difficult for a conventional continuum-based approach such as the finite element method (FEM) to model the rock fragmentation by blasting and the expansion work on the rock by explosive and its detonation products. In this paper, the particle blast method (PBM) was employed to model the behaviour of the detonation and a bonded particle model (BPM) was used to model the brittle material to be blasted. A mortar cylinder with a centrally placed hole for the explosive was modelled and the results were compared to the experimental data. The blast process from crack initiation to fragment formation was analysed. The influence of coupling ratio on fragmentation was also investigated.CITATION:Yi, C and Johansson, D, 2015. Discrete element modelling of blast fragmentation of a mortar cylinder, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 793–798 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By T Suwa, S Ishida, J Xue, S Fuchida, H Shimada, Y Aoki, C Tokoro

Pyrite depression with prolonged pre-conditioning treatment in high salinity water has attracted much of researchers’ interest in recent years considering the increased utilisation of multiple stage flotation, closed water circuits, clay minerals, and sea water in flotation plants. In this study, the role of calcium (Ca)/magnesium (Mg) precipitates in stabilising the dissociative ferric hydroxy-xanthate (FHX), and its effect on modifying the balance of hydrophobic/hydrophilic species on the pyrite surface were primarily investigated. The total amount of extractable Fe-bearing species on pyrite concentrates and tailings after floatability test was quantitively determined using ethylenediaminetetraacetic acid (EDTA) extraction tests combined with inductively coupled plasma optical emission spectroscopy (ICP-OES). A more evident accumulation of extracted-Fe in pyrite concentrates rather than it in pyrite tailings was observed at both pH 9 and 10.5 when pyrite was pre-conditioned in Ca/Mg-bearing solutions for 360 min. Fourier transform infrared (FTIR) spectroscopy showed the main xanthate derivatives changed from di-xanthogen (1155 cm-1 ) to FHX (1167 cm-1 ) on the oxidised pyrite samples that were preconditioned in Ca/Mg-bearing solutions. Scanning electron microscopy-energy dispersive spectrometry (SEM-EDS) suggested the preferential accumulation of FHX upon secondary Ca/Mg-bearing precipitates as reflected by the higher Fe/S ratio together with the decrease of O element herein after xanthate conditioning. Although the hydrophilic secondary Ca/Mg/Fe-bearing minerals on the pyrite surface generally deteriorate pyrite’s floatability, the upper section of these secondary hydrophilic aggregates is partially covered by FHX alongside with further multilayer-adsorbed di-xanthogen. The precipitated Ca/Mg-bearing precipitates promotes the immobilisation of dissociated FHX derived from the reaction among iron oxyhydroxides and xanthate anions upon the localised secondary Ca/Mg/Fe-bearing minerals via acid–base complexation. Therefore, this phenomenon alleviates the hydrophilic modification of secondary Ca/Mg/Fe-bearing minerals to pyrite considering the immobilised FHX upon localised precipitates shows a slight hydrophobicity, and meanwhile, the upper FHX benefits the multilayer adsorption of di-xanthogen via the interaction among their inner hydrophobic alkyl chains.

Aug 24, 2022