Search Documents

By Earl R. McMillan

Though much has been written during the past several years about the Russian success in using hydraulic jets for coal mining, little or none of the published information, in so far as this writer has observed, has been of any use or practical application in this country. It is true, according to their published reports, that the Russians were pioneers in the use of high-pressure water jets in the mining of coal. They report the use of water jets for this purpose as early as 1936. However, according to a survey of foreign literature on the subject made by the U.S. Bureau of Mines1 a few years ago, water jets in the USSR, as well as in other nations including New Zealand, Poland and West Germany, were used principally to sluice the loosened coal after it had been previously drilled and blasted, rather than to cut or break it from the solid face. The interest of the Northern Pacific in the potential application of a high-pressure water jet to the actual extraction of coal, particularly in steeply dipping beds, originated in a visit by this author to the operations of the American Gilsonite Co. at Bonanza, Utah, in March 1958. After seeing the extraction, on a commercial basis, of gilsonite from a 22-ft wide vertical vein of this solid material with a 3/8-in. diam stream of water under approximately 2200 psi, it was felt that, with some modifications, water jets were the solution to the problem of economically mining the steeply dipping (i.e., steeper than 20º) coal beds in the State of Washington.

Jan 6, 1962

By R. A. Harrington, H. R. Nelson

The: structure of anodic films formed on aluminum and other metals under varied conditions is not well known despite the wide use of such films both as protective coatings and as the dielectric medium in electrolytic condensers. The present work was undertaken as a survey of the possibilities of electron diffraction in the investigation of anodic films, especially in comparing the properties of anodic films formed under different sets of conditions and subjected to various subsequent treatments. In addition, an effort has been made to compare surface films formed on aluminum by anodic treatment with surface films formed by heating, immersion in chemicals, etc. The elcctron diffraction method in many cases has been successfully applied to the study of thin surface films. Its principal advantage is that it can be used without removing the films from the base material upon which they have been formed. The low penetrating power of electrons, in the "reflection" diffraction method which has been used in this work, prevents the appearance of diffraction patterns from substances at depths greater than about 100 Angstrom units (lop6 cm.). Different investigations of the structure of anodic films have showll widely varying results, depending on the methods used in preparing the films. Apparently under some conditions these films are crystalline and under other conditions they are amorphous, and it has been difficult to say which type of structure will be found in any particular case. Schmid and Wassermann's1 X-ray diffraction patterns of eloxal‡ films show two broad, diffuse bands, which these investigators attribute to finely divided cubic y-Al2O3.§ Burgers, Claassen, and Zernicke³ obtained sharp X-ray

Jan 1, 1940

By R. A. Harrington, H. R. Nelson

The: structure of anodic films formed on aluminum and other metals under varied conditions is not well known despite the wide use of such films both as protective coatings and as the dielectric medium in electrolytic condensers. The present work was undertaken as a survey of the possibilities of electron diffraction in the investigation of anodic films, especially in comparing the properties of anodic films formed under different sets of conditions and subjected to various subsequent treatments. In addition, an effort has been made to compare surface films formed on aluminum by anodic treatment with surface films formed by heating, immersion in chemicals, etc. The elcctron diffraction method in many cases has been successfully applied to the study of thin surface films. Its principal advantage is that it can be used without removing the films from the base material upon which they have been formed. The low penetrating power of electrons, in the "reflection" diffraction method which has been used in this work, prevents the appearance of diffraction patterns from substances at depths greater than about 100 Angstrom units (lop6 cm.). Different investigations of the structure of anodic films have showll widely varying results, depending on the methods used in preparing the films. Apparently under some conditions these films are crystalline and under other conditions they are amorphous, and it has been difficult to say which type of structure will be found in any particular case. Schmid and Wassermann's1 X-ray diffraction patterns of eloxal‡ films show two broad, diffuse bands, which these investigators attribute to finely divided cubic y-Al2O3.§ Burgers, Claassen, and Zernicke³ obtained sharp X-ray

Jan 1, 1940

By W. F. Wheeler

In the study of the coals of Illinois now being carried on by the State Geological Survey, an attempt is being made to determine the most satisfactory basis of comparison between different coals. The following discussion is based upon work done for the Survey in the laboratories of the State University and under the general direction of Prof. S. W. Parr. "Pure coal" has been defined by Mr. A. Bementl as ash- and moisture-free coal, and the use of this pure coal" as a basis for comparing different bituminous coals has lately been much discussed among engineers in the middle West. By some the B.t.u. of the pure coal is being used to check calorimetric results, and to calculate the calorific value of different coal-samples from the same seam, for which purposes it is necessary to assume—first, that the composition and calorific value of pure coal from different parts of the same coal-seam are uniform, and, second, that these values remain constant after the coal is mined, both of which assumptions there are reasons to believe are inconsistent with the facts. Certain variables are included in pure coal, as ordinarily defined, and disregard of them may lead to serious error. In any event, where delicate shades of difference are involved, no sure interpretation of results car] be made, unless these variables be eliminated. As a basis of comparison between coals, ash- and moisture-free coal is much to be preferred to " dry coal," and still more is it to be preferred to moist coal," as ordinarily reported in analyses. There are, however, two constituents other than ash

Jan 1, 1908

By Duane H. Haley

Dr. F. Well, the first thing that you have to realize is what is the Bureau of Mines? The Bureau of Mines basically has two functions. First it does the research and development relating to mining, processing, conversion, refining, recycling and substitution for minerals and materials. We work hand in hand with the U. S. Geological Survey on the geological end, although the exploration part of the game is theirs, and there is a very good relationship between the Survey and the Bureau of Mines. There are some overlaps with the Office of Coal Research, and we expect to be able to straighten out the areas of overlap, because it's important than OCR and the Bureau work together. Both the Office of Coal Research and the Bureau of Mines will have increased budgets next year, assuming that they are appropriated by the Congress. The other general area is in the whole area of mineral policy. The Bureau of Mines again is the key agency for developing data and analyses and making recommendations on all types of mineral policy in the Federal Government. It's a focal point for all types of minerals activities. It's the only real centralized focal point, along with the USGS, in the whole Federal Government. The problem areas, to answer your question specifically, are first of all the Bureau of Mines budget this year is $105 million and the budget for next year is $215 million, so it's more than double. Now, assuming that this budget is appropriated by the Congress, most of that money will be used for research and development in the energy area.

Jan 4, 1974

By Reginald S. Dean

THE commercial availability of electrolytic manganese has greatly changed the position of manganese as a nonferrous alloying metal. Manganese metal commercially available up to about ten years ago was reduced with either silicon or aluminum and contained substantial amounts of the oxides of these metals and other impurities. Manganese was accordingly not available as an alloy base and its addition to copper-base and nickel-base alloys was generally limited to a manganese content of a few per cent. Several special alloys like manganin contained up to 12 pct of manganese. A method for the production of electrolytic manganese was developed by the Bureau of Mines in 1936 and commercial production was begun in 1938. At the present time (June 1951), production is about 12 tons per day but appears likely to be substantially increased. Electrolytic manganese is deposited from an aqueous electrolyte containing manganese and ammonium sulphates and is marketed as cathode fragments about 1/8 in. thick. The impurities in its composition are as follows: iron, 0.0015 pct; copper, 0.001; arsenic, 0.0005; cobalt, 0.0025; lead, 0.0025; molybdenum, 0.001; sulfide sulfur, 0.017; sulfate sulfur, 0.014; insoluble, 0.002; carbon, 0.002; hydrogen, 0.015. These figures are from Bulletin 463, U. S. Bureau of Mines. From an alloying standpoint, the most important impurity is hydrogen. This can be removed by heating; 95 pct of the hydrogen can be removed in this way without introducing significant amounts of oxygen or nitrogen. Much of the commercial electrolytic manganese used in alloys is dehydrogenited by the producer, since the amount

Jan 1, 1953

By Berlen Moneymaker

THE development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration, Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its princi-pal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration.

Jan 1, 1938

By George B. Lee

During the two years in which the new reduction-works of the Copper Queen Consolidated Mining Co. have been in operation at Douglas, Ariz., there has developed a remarkable condition in regard to the corrosive action of the water used to cool the jackets of the blast-furnaces. Were it not for the many contradictory features, it might pass as one of the unavoidable troubles due to the composition of the water. This water, obtained from wells 600 ft. deep, is also used in the steam-boilers, and its composition, as shown by the following analysis, does not indicate the presence of any ingredient which would explain the corrosion: Grains Per U. S. Gal. Silica,...........0.861 Iron oxide and alumina,....... 0.223 Calcium carbonate,....... 0.261 Calcium sulphate,................. Magnesium carbonate,........... Sodium and potassium sulphates,..14.850 Sodium and potassium chlorides,.9.732 Sodium and potassium carbonate, . 6.482 32.409 The jackets are made of inner plates 0.5 in. thick and an outer plate # in. thick, with 3/8-in. stiffeners between the inner and outer plates. In from 10 to 12 months the inner plates have been reduced by corrosion to a thickness of from + to & in., while the outer plate in the same time is reduced by less than 1/16 in., and the stiffeners show very little corrosion. The plates are pitted and eaten away in some places more than in others. There is practically no scale found on the jackets, but when cleaned considerable iron oxide is found in the bottoms. With an action so marked, serious trouble would be expected in the boilers, but, on the contrary, a recent inspection by a

Jan 1, 1908

By K. L. Temple, A. R. Colmer

ACID coal mine drainage presents a peculiarly difficult problem for two principal reasons. First is the fact that the amount of acid water discharged from active and abandoned mines constantly increases as coal fields are developed and thereby creates a steadily worsening nuisance of rapidly growing importance to the general public as well as to the coal industry. Second is the even more significant fact that there is no method yet known that will appreciably alleviate the acid water problem except at totally prohibitive cost to the coal operators. The problem is thus seen to be an urgent one. With a growing need for good quality water and a growing public demand for abatemknt of stream pollution, a large portion of the soft coal industry finds itself in the position of year by year dumping more and more acid into the streams and waterways and having no way in sight of improving the situation or even of keeping it from getting worse. While some studies have been made, it is only in the last few years that the problem has been seriously considered, chiefly by the group of workers under the direction of S. A. Braley at Mellon Institute and by the Bituminous Coal Research, Inc. fellowship at West Virginia University. Hinkle and Koehlerl reported the results of the earlier West Virginia work. This work pointed to certain biological aspects which had not been noticed previously. These may be summarized as two separate findings. One was that sulphur oxidizing bacteria were present in acid mine water and that their possible role in contributing to the acidity should be investigated. The other was

Jan 1, 1952

By E. W. Schilling

THE-separation of hematite by hysteretic repulsion was first brought to the attention of the public in 1922, by W. M. Mordey1. Three-years later another paper2 was published and after another four years a third paper3 appeared in the South African publications. Certain data were lacking in these papers. In order to continue the work intelligently a knowledge of the shapes of the hysteresis curves for certain minerals was very necessary. This information was not available until the present year4. It was known that reduction of certain ores rendered them amenable to this process of separation but definite data in. the form of curves showing exactly the effect of such treatment were lacking. Prob-ably our best source of information on the separation of minerals by the use of alternating-current magnetic fields today is the reports from the U. S. Bureau of Mines 5-7. It is not the purpose of this paper to tell the reader in detail how to make a commercial separator. Experimental models have recently been made7 and the results obtained have been so good that it is the opinion of the authors that the public will soon take an active interest in the subject and its development. The writers have constructed a separator that is considerably different in construction and operation from the two types described by Mr. Davis. This will be described; but the real purpose of this paper is to outline certain experiments and give curves showing data that have a fundamental bearing upon the practical construction of a separator of this type.

Jan 1, 1936

By W. L. Grose, J. E. Nealy

A device developed by the U.S. Bureau of Mines for the detection and quenching of coal mine explosions suffers from the inability to discriminate between the light emitted from hydrocarbon combustion and that emitted by electrical sparks and miner's cap lamps1. Since the quenchant device is activated by an internal explosive charge, the possibility of serious injury to nearby personnel demands a detector which can reject false signals. Described herein is a detector which can provide a rapid response signal upon the emission of radiation from hydrocarbon combustion and concurrently reject spurious signals from such sources as sparks and cap lamps. It was suggested that a detector might be developed to operate on the principle of monitoring the radiation intensity emitted from two separate spectral regions and ratioing the intensities2. A series of experiments was conducted for combustion of methane-air mixtures which demonstrate the ability of such a detector to discriminate between combustion and spurious signals. Experimental Apparatus A cylindrical (3.8 in. diam by 12 in.) stainless-steel shock tube test section was used as a combustion chamber. The test section was equipped with quartz windows (2 in. diam) on either side, a piezoelectric pressure transducer, and two steel electrodes. A 10-kv capacitor discharged across the electrodes provided a submicrosecond duration spark to ignite the gas mixture within. The desired partial pressures of methane and air were obtained by using a Wallace and Tiernan 0-800 mm Hg pressure gauge with which pressures could be determined to an accuracy of % mm Hg. All tests were conducted with a total pressure of 1 atm in the chamber. To

Jan 1, 1972

By G. H. Anderson

H. R. HANLEY*—I have been asked to discuss briefly the development of rotating cathodes for the electrolytic deposition of cadmium. The earliest recorded use of rotating cathodes was by Hoepfner at Frufurt, Germany about sixty years ago. He elec-trolized zinc chloride solution using diaphragms to separate electrodes. In the early experimental work of the Bully Hill Copper Mining and Smelting Co., Shasta County, Calif., rotating aluminum cathodes 4 ft in diam were used in the electrolysis of an acid zinc sulphate solution. Finished cathodes weighing up to 400 lb were produced. Because of mechanical difficulties, this type of cathode was abandoned for zinc, but was later used for cadmium because of the relative smoothness of deposit in comparison with stationary plates with comparable current densities. Cadmium sponge which forms on the cathode at moderate current densities (without special treatment) is entirely eliminated by a slow rotation. The rate of rotation of the cathode has an effect on the mechanical nature of the deposit. A high rate of rotation concentrates the adhering electrolyte on the shaft; a moderate rate appears to concentrate on the cathode a short distance out from the shaft tending to corrode the deposit in the form of a ring. At a very slow rotation (2 to 3 rpm) the adhering electrolyte gravitates nearly vertically, thus avoiding the cutting ring referred to above. The true explanation for the smoother deposits obtained on rotating cathodes may not be given definitely as the numerous factors involved are not thoroughly understood. Smooth deposits are obtained when the orderly growth of the metal crystals in the cathode lattice are disorganized. Thus the crystals form and grow for a very short interval when they are arrested and a new crystal forms. The continued growth of the original crystals provides large crystals and a rough deposit. Also if the acidity of the electrolyte is low, hydrogen gas bubbles adhere to the deposit. As the cathode is rotated the gas surface is brought into the atmosphere where they burst; thus the deposit is made on a surface relatively gas-free. An aluminum hub distance piece was riveted to each aluminum disk 4 ft in diam, slipped on a 4 1/2 in. steel shaft and pressed tight to prevent acid electrolyte seeping through to the shaft. The 9-cathode assembly was supported on insulated bearings. Electrical contact to the shaft was made through what was equivalent to a copper pulley. Sufficiently high conductivity brushes were placed on the face of the pulley to lead the current to the cathode bus bar. The assembly was driven by a link belt contacting a sprocket insulated from the shaft. The lead anodes were semicircular and supported on porcelain insulators placed on the bottom of the cell. Two anodes were provided for each cathode to permit an 8-in. space between them without increasing the ohmic resistance. This ample spacing permitted easy stripping of deposit with the assembly in place. Cathode cadmium was melted under 650 W cylinder oil. After casting, the primary slabs were remelted under molten caustic soda and cast into pencils 1 1/32 in. in diam. Rotating cathodes for deposition of cadmium are used at Risdon, Tasmania, and at Magdeburg, Germany. W. G. WOOLF*—This paper is very-interesting to me because in our work at the Electrolytic Zinc Plant of the Sullivan Mining Co. we had an exactly similar problem—that is, a method of producing cadmium from our purification residue, the recovery of the contained copper as a copper precipitate which could be sent to a copper smelter and the production of merchantable cadmium. It is interesting to me, not knowing of the work of the Risdon people, how closely we approximate them in their main metallurgy, diverging at several interesting steps which I would like to discuss for just a moment. For example, at Risdon they oxidize their purification residue. In our practice we take the current residue as it is produced in the purification department of the zinc plant and process it in the cadmium plant. The only oxidation that it obtains is the oxidation in the presses, the dumping of the presses and the collection and transportation of the residue to the cadmium plant. We find that the leaching of that residue does not necessarily require the oxidation step that the Risdon people evidently find necessary. The discussion of oxidation comes in again in the matter of the treatment of the precipitated cadmium sponge with zinc dust which again at Risdon is oxidized but which we do not attempt to oxidize except as it oxidizes itself in the storage. There is a partial oxidation which cannot be avoided, as Mr. David-sou pointed out, but we make no attempt to attain a complete oxidation and we dissolve the cadmium sponge in the sul-

Jan 1, 1950

By G. A. Vissac

O. R. LYONS *—I wish to thank Mr. Vissac for his compliment. I hope that his paper is not only well received, but that it will serve to bring forth more papers on the subject of thermal drying. One of the primary purposes of the work performed by Battelle for Bituminous Coal Research in investigating the thermal drying of coal was to stimulate other investigators and to get them to contribute their knowledge in the form of papers such as this one. We at Battelle and the personnel of Bituminous Coal Research are very gratified that Mr. Vissac and other persons have responded in this matter of the thermal drying of coal. I wish to state that I think that Mr. Vissac's paper is a very clear and easily understood description of a method of calculating the design requirements for a screen type drier, and I think that it would be exceedingly valuable to operators and to those who intend to purchase any type of thermal drier and use it in the future, if the manufacturers or operators who have such information for other types of driers would provide the same type of information for the other makes of driers now on the market. 1 also wish to point out—an idea that is new to me, and I know is new to most of the operators of driers in the United States-—the idea of recovering the heat that is normally lost in the coal and in the exhaust gases. This heat is not being recovered at most (of the thermal drying operations in the United States, and the possibility of recovering it should be called to the attention of every single one of those operators. I know many of them have never given any thought to the matter, but they will be interested once they realize the ease with which it could be done and the savings that could be realized. I also wish to compliment Mr. Vissac for presenting the method of analysis that he uses to determine the difficulty of drying any particular coal. It is a very simple method, and yet it seems to me that it should be a very effective, very efficient method for determining the difficulty of drying for his particular problems. C. Y. HEINER*—I do not know that I can add anything very illuminating to what Mr. Vissac has said. I think anything that Mr. Vissac said in regard to coal drying is a contribution because, to my personal knowledge, he has studied the matter carefully for many years and made many valuable contributions. I am not too familiar with coal drying problems in the east, but I know in the west we have not made enough coal drying studies. I think coal operators too often just take the coal as it is and make more or less the best of it. There are relatively few washing plants in the west now, and so the problem has not come to the front as much as it probably will in the future. In this connection, it seems to me that this matter of drying the raw coal, as Mr. Vissac brings up, is an extremely important one. We have not a continuous miner ourselves, yet, but we expect to get some this year, and we think the percentage of fine coal-—that is, minus 3/16 in.—will double. We have about 20 pct minus 3/16 in. in the 8 in. by 0 size now, and we think we will likely have 40 pct, which will have a surface moisture of the order of 8 pct. To wash it satisfactorily, we will have to dry the raw coal first in order to screen it, and after that, I suppose, there will have to be dry cleaning of some sort. We have not really used dry cleaning on fines in the west yet to my knowledge, but it is a matter that has to be faced by the industry, and I am very hopeful that Mr. Vissac's study will assist us in that connection. W. L. McMORRIS*-In my company we are preparing largely metallurgical coal for a great number of byproduct coke plants. The most outstanding thing to me about the requirements of moisture in the finished product is that there is a different requirement for almost every coke plant. Each operator has a different set of factors on which he establishes his coking costs where they involve moisture. For our corporation operations in Birmingham, my company does not produce the coal, but in Birmingham they are getting away with moistures very much higher than our plant at Clairton, Pa., would tolerate. The moisture that we have to produce for the plants along the lakefront where they are subject to much more severe weather is something else again. We have not tackled heat drying, primarily because our customers do not know what heat drying will do to the coking characteristics of the coal. If the temperature of drying can be held down

Jan 1, 1950

By Koichi Kashida, Mayumi Someno, Kazuhiro Goto

The present work has two objectives: first to develop an experimental method which would give some new information on the micromechanism of the reduction of oxides by gases at elevated temperature; second to clari,fy the intermediate phases of the W-0 system, formed during the reduction. A Galvanic cell with the solid electrolyte , ZrO2 . CaO, was imbedded in powders of W03, CuO, or Fe20s with two measuring electvodes and with a reference electrode. The change of the intraparticle gas composition was measured at An oxygen concentration cell consists of two electrodes separated by an electrolyte through which the transference of electrical charge is accomplished predominantly by the migration of oxygen ions. Many works have been reported on the oxygen con- 600" to loo@ C during the reduction by the gas mixture of hydrogen and argon. The intraparticle gas composition changes stepwise with time. The electromotive force of such temporary interruption corresponds to the equilibrium electromotive force of two solid phases formed during the reduction. The intermediate phases of W-0 system, which are formed in a large quantity during the reduction by hydrogen, are W0 2 W02.72 and WOz. The micromechanism of the reduction of oxides by gases is discussed. centration cells with the solid electrolyte of solid solution of zirconia and lime, since Kuikkola and wagnerl demonstrated the possibility of determination of standard free energy of formation of oxides by an electromotive-force method with the Galvanic cell. One of the present authors (K.G.) and his coworkers have applied the cells with the solid electrolyte of zirconia and lime to the following measurements:

Jan 1, 1969

By R. G. Stickney

INTRODUCTION The Basalt Waste Isolation Project, conducted by Rockwell Hanford Operations under contract to the U.S. Department of Energy, is assessing the feasibility of the disposal of commercial radioactive spent fuel/high-level waste in deep geologic formations in basalts beneath and within the Hanford Site in southeastern Washington State. The Basalt Waste Isolation Project mission is to identify and characterize a potential geologic repository site in basalt and to develop associated facilities and technology required for the potential permanent isolation of radioactive wastes in basalt formations. In support of the Basalt Waste Isolation Project, a laboratory testing program was conducted to evaluate the performance of the Council for Scientific and Industrial Research's "Doorstopper" biaxial strain cell. To support site characterization studies and the design of repository openings, in situ stress measurements will be conducted within the reference repository horizon (~970 m). The Doorstopper is one of the instruments being considered for use in these measurements. It was selected because it requires only a small volume of work to achieve stress relief, which is important in a closely jointed basalt. Also, test durations are short, permitting a large number of measurements to be made within a given time to increase confidence in the results. Within the reference repository horizon, temperatures are expected in the range of 40º to 60°C with a humidity of up to 100%. For this testing program, test conditions were selected to closely resemble those expected within the repository horizon. The Doorstopper test, mainly developed by Leeman (1964), is a strain rosette relief method of measuring rock stress in situ. The Doorstopper consists of a four element, 45º strain gage rosette

Jan 1, 1984

By Richard A. Brown

The direct precipitation of uranium with hydrogen peroxide has been known since 1877. Commercial use of the process began in the 1960s. During 1967 the US Bureau of Mines (USBM) assisted the Climax Uranium Co., Grand Junction, CO in the development of a uranyl peroxide precipitation process to control a molybdenum impurity problem (Shabbir and Tame, 1978). Atlas Minerals, Moab, UT has used hydrogen peroxide to control vanadium and sodium levels in uranium concentrates since 1969 (Caropresso and Badger, 1973). Recently, the use of hydrogen peroxide by the uranium industry has grown, particularly since the increased demand for uranium has led to the processing of low grade ores. Impurities present in low-grade ores can be concentrated with the uranium during milling and will substantially complicate the refining of uranium yellowcake concentrates. Consequently, commercial nuclear fuel processors have imposed stringent specifications and penalties to control these impurities. The ability to produce a pure uranium yellowcake can eliminate penalty or reprocessing costs. Hydrogen peroxide precipitation of uranium is specific and quantitative, producing a very high purity product. Although the hydrogen peroxide precipitation of uranium has, and continues to be used primarily as means of producing a high purity yellowcake, it has also become an important process due to the superior physical properties of the precipitate. Under normal operating conditions, the precipitate produced by the reaction of hydrogen peroxide and uranium is dense, easily filtered and dried. The final dry yellowcake is pure, high U308 assay product. Consequently, processing costs such as filtering, drying and/or calcining and drumming, can be reduced compared to ammonia, caustic or Mag-Ox precipitation.

Jan 1, 1982

By Will H. Coghill, Fred D. DeVaney

THE coercimeter, as its name implies, is an instrument for measuring the coercive force[+] of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub- sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. The turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1938

By James L. Calver

Fuller’s earth is an inexact term applied to certain clays that have a marked ability to adsorb coloring materials from animal, vegetable, and mineral oils. Many clays have this adsorbing power to a slight or very limited degree, and certain other clays, chiefly bentonites, as well as minerals such as bauxite, can be made highly adsorbent by activation with acids or alkalies, but the term fuller's earth is generally reserved for clays that are naturally highly adsorptive. In most fuller's earths and practically all activable clays montmorillonite is a dominant mineral. No definite clay mineral or group is implied in the name fuller's earth, and the distinction between fuller's earth and other clays that have more or less bleaching power is not sharply drawn. The name as generally used has no genetic or mineralogical significance. The fuller's earth produced in the Florida-Georgia district contains the clay mineral attapulgite. This mineral name was first used in 1930 by DeLapparent to apply to a hydrous aluminum magnesium silicate found in the fuller's earth from Attapulgus, Ga., and Quincy, Fla. An essential component of its structure, determined by Bradley in 1940, is that the silica chains of the molecule are arranged similarly to those of the amphibole minerals. The fibrous nature of the lath-like crystals of attapulgite is apparent under magnifications reached by the electron microscope. The ideal formula, [(OH,), (OH), Mg, Si, 0,-4H,O], contains no aluminum, but there is considerable replacement of the magnesium by aluminum. In the classification of clay minerals, attapulgite is associated with sepiolite and polygorskite rather than with mont-morillonite.

Apr 1, 1956

By Harwick Johnson, E. W. Schilling

THE separation of hematite by hysteretic repulsion was first brought to the attention of the public in 1922, by W. M. Mordey1. Three years later another paper2 was published and after another four years a third paper3 appeared in the South African publications. Certain data were lacking in these papers. In order to continue the work intelligently a knowledge of the shapes of the hysteresis curves for certain minerals was very necessary. This information was not available until the present year4. It was known that reduction of certain ores rendered them amenable to this process of separation but definite data in the form of curves showing exactly the effect of such treatment were lacking. Probably our best source of information on the separation of minerals by the use of alternating-current magnetic fields today is the reports from the U. S. Bureau of Mines5-7. It is not the purpose of this paper to tell the reader in detail how to make a commercial separator. Experimental models have recently been made7 and the results obtained have been so good that it is the opinion of the authors that the public will soon take an active interest in the subject and its development. The writers have constructed a separator that is considerably different in construction and operation from the two types described by Mr. Davis. This will be described, but the real purpose of this paper is to outline certain experiments and give curves showing data that have a fundamental bearing upon the practical construction of a separator of this type.

Jan 1, 1935

By J. B. Ackerman, J. D. Miller

Alunite [KA13(S04)2(OH)6] is a promising non-bauxitic aluminum resource, the domestic reserves of which are estimated to be 800 x 106 tons at 35 percent alunite. The major gangue mineral associated with alunite is quartz. The thermochemical process that has been developed for treatment of this ore does not provide for the initial removal of gangue prior to processing. In this regard, it may be desirable to concentrate the ore to gain significant technical and economic advantages. Experimental results indicate the effectiveness of an oleic acid flotation technique and exemplify the problems encountered in fine particles processing. These results show that the quality of separation studied as a function of temperature, collector addition, and depressant addition is dependent on the degree of liberation achieved during size reduction. At coarse grinds the quality of separation was limited by the presence of locked particles while for finer grinds where more extensive liberation is achieved, better separations were obtained. The degree of liberation for each size interval was determined by an SEM/energy dispersive x-ray technique and found to be independent of the extent of size reduction, suggesting that liberation occurs by indiscriminate fracture and not by detachment. Up to 89 percent liberation was realized for a minus 400 mesh grind. Under these circumstances, the quality of separation appears not only to be limited by the remaining locked particles, but, also, by contamination of the alunite concentrate with fine quartz gangue (< 2µm). The best separation for the minus 400 mesh grind was a rougher recovery of 88 percent with a grade of 65% alunite at 50°C.

Jan 1, 1980