Search Documents

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers.1, 2, 3, 4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The cndursnce limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers.1, 2, 3, 4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The cndursnce limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

By Valentin R. Garfias

PRODUCTION AND MARINE TRANSPORTATION OF MEXICAN PETROLEUMS ALTHOUGH the work on which this paper is based was carried on, by the writer as Special Commissioner of the Petroleum Department of the Mexican Government, the opinions expressed are only his personal views for which the Mexican Government can in no way be held responsible. Notwithstanding that the appointment covers all phases of the so-called petroleum question, as the one question of immediate importance was that relating to taxation, it was decided to devote all the time to this phase of the work. The present report has been divided into two closely related parts, .the first dealing with the production and marine transportation of Mexican petroleum, and the second, with the Mexican taxation on petroleum and its products. The writer wishes, to acknowledge the loyal cooperation rendered by Mr. M. C. Ehlen, who had charge of the statistical, work, and by Miss S. Stern and Messrs. E. P. Heiles and J. E. Morrissey. The aim throughout the work has been; to pave the way for a thorough understanding between the Mexican Government and the oil operators and to present a true and clear statement of facts relating to the questions at issue.

Jan 2, 1921

By Charles Mitke

(San Francisco Meeting, September, 1915) INTRODUCTION THE Copper Queen mine is composed of seven divisions which are operated through the following shafts: Division Shaft Depth, Air Current No. Feet Uncle Sam 600 Downcast (shut clown April, 1914, to 1 curtail production) Southwest 600 Downcast 2 Czar 400 Downcast 3 Holbrook 600 Downcast 4 Spray S00 Downcast (shut clown April, 1914, to curtail production) 5 Gardner 1,000 Downcast 6 1 Dallas 1,400 Downcast 1 Lowell 1,600 Upcast 7 Sacramento 1,700 Downcast " I I The workings of the different shafts are connected by motor-haulage drifts on the even numbered levels. The general location of the orebodies and workings is illustrated by the vertical projection of orebodies of the district as shown in Fig. 1. The Uncle Sam, Southwest, and Czar workings have many connections to the surface through raises and extensive cracks that were caused by moving ground. These divisions are cool and are ventilated entirely by natural means. The Holbrook is ventilated partly by natural and partly by artificial ventilation, while the Spray, Gardner, Lowell; and Sacramento are ventilated entirely by mechanical means. In some of the divisions mentioned above a considerable quantity of air exhausts through shafts of adjoining properties.

Jan 9, 1915

By AIME AIME

THE session* on Non-ferrous Metallurgy held Monday morning was conducted in a most satisfactory manner with F. F. Colcord, vice-president, U. S. Smelting Co., in the chair. In spite of the early hour and the fact that members desired to register first, the meeting started quite promptly, with almost every chair in the room occupied. About 65 men were present and during the morning many more came but, not being able to find room, drifted away to other fields of activity. The first paper presented, "Lead Refining Practice of the Bunker Hill Smelter of the Bunker Hill & Sullivan Mining & Concentrating Co.," by Alfred F. Beasley (T. P. 303), was read in abstract by Edward H. Robie, and an animated discussion followed in which Messrs. Johnson (written discussion), Brewer and Jones and Professor Hayward participated. The discussion hinged principally on the liquation of the zinc crusts, but Professor Hayward called attention to the fact that the practice of keeping the gold and silver crusts separate was not new and the present scheme illustrated the axiom that processes based on fundamental principles should not be considered as extinct; one can never tell when it may be found advantageous to make use of them again.

Jan 1, 1930

By I. Iwasaki

The steel industry is facing an unprecedented challenge. I would like to point out the role that flotation technology could play in meeting this challenge by providing high quality raw materials to the steel industry. Of all the technology available to a blast furnace operator, raw material preparation is by far the most important. Raw material preparation has been a key to the success of the Japanese steel industry. The foremost proponent of better raw material preparation was Professor Joseph at Minnesota. He gave a Howe memorial lecture to the AIME audience in the early 1950s, prepared from the lecture notes that he gave in his classes. At about that time he was invited to Japan. It is ironic that the Japanese steel industry listened and made it a success. In order for our steel industry to be competitive, first we must supply high quality and uniform quality raw materials to improve the efficiencies of our blast furnaces. Where does flotation fit in to the iron ore industry then? First, as a primary means for concentrating for oxidized iron ores. Second, to touch up magnetite concentrates for the removal of the last few percent of silica. And third, in the preparation of super-concentrates for direct reduction.

Jan 1, 1984

By Frank C. Appleyard

The two calcium sulfate minerals-gypsum and anhydrite-occur in many parts of the world, and gypsum has long been of economic importance in the family of industrial minerals. Gypsum, the dihydrate form of calcium sulfate (CaS042H20) and anhydrite, the anhydrous form (CaSO4) are frequently found in close association, and it is seldom that a calcium sulfate deposit will consist exclusively of one mineral or the other. Although known gypsum deposits are extensive, anhydrite makes up the largest part of total calcium sulfate reserves. However, it has very minor economic use, and most of the following discussion will be devoted to gypsum. Calcium sulfate is one of the principal con- stituents of evaporite deposits, and when pure, has the following composition: [ ] Deposits of pure gypsum or of pure anhydrite which are large enough to be considered commercial have never been found because of both the metastable relationship between the two minerals, and the presence of impurities such as calcium or magnesium carbonates, chlorides, other sulfate minerals, clay minerals, or silica. As a result most mine production of gypsum will range between 85 and 95% pure. Often it is used as mined, although in certain cases, one or more forms of mineral beneficiation are employed to upgrade the product.

Jan 1, 1975

By Edwin Ludlow

EDWIN LUDLOW, the 41st President of the A. I. M. E., died in Muskogee, Okla., on Feb. 10, 1924, after a brief illness of influenza followed by pneumonia. He was born in Oakdale, Long Island, N. Y., March 12, 1858, a son of William Handy and Louise (Nicoll) Ludlow, attended Flushing (L. I.) Institute 1868-75: and Columbia School of Mines (N. Y.) where he graduated with the degree of Engineer of Mines with the Class of 1879. After graduation his first employment was as assistant engineer in river and harbor work on the Delaware River near Philadelphia. In 1881 he went to Mexico as one of the engineers on the Mexican Central Railroad, then building from Laredo, Texas, to Mexico City. The road being in financial difficulties he returned to the United, [states, and shortly thereafter was made superintendent of the Union Coal Co.'s collieries located in the western middle anthracite field, between Shamokin and Mt. Carmel. Ludlow and Arthur H. Storrs, then superintendent of the Neilson Shaft Colliery, in Shamokin, were known throughout that section as the baby superintendents, both under 25 years of age. The appointments of such young men were at that time unique and set a record for youthful assumption of re-

Jan 1, 1924

By Keith Leonard Sutherland, Ian William Wark

Mercaptobenzthiazole and its sodium salt are marketed under the trade names Flotagen and Flotagen S respectively, for use as collectors for cerussite and other minerals. The structural formulas for sodium rnercaptobenzthiazole and for sodium ethyl xanthate are: Chemically there is a resemblance between the two compounds, though the free acid (mercaptobenzthiazole itself) is much more stable than xanthic acid. Both are readily oxidized, e.g., by iodine to disulphides, and can be estimated by iodometric titration. Qualitatively they are similar as collectors in flotation, although there are quantitative differences between them that may be important in practice. It is deduced that the influence of the nitrogen atom is subordinated to that of the sulphur atoms, and that the dominant group of these compounds is the mercapto group —SH or —5Na. The general method of investigation has been based on contact tests. Two temperatures, 10" and 35" C., have been chosen, and with a standard concentration of 20 mg. per liter of mercaptobenzthiazole (i.e., of the free acid) the influence of alkali, cyanide and copper sulphate on contact at sulphide mineral surfaces has been studied. This standard concentration corresponds to about 19 mg. per liter potassium ethyl xanthate; it brings out the differences between the minerals better than a higher concentra-

Jan 1, 1939

By Ian William Wark, Keith Leonard Sutherland

Mercaptobenzthiazole and its sodium salt are marketed under the trade names Flotagen and Flotagen S respectively, for use as collectors for cerussite and other minerals. The structural formulas for sodium rnercaptobenzthiazole and for sodium ethyl xanthate are: Chemically there is a resemblance between the two compounds, though the free acid (mercaptobenzthiazole itself) is much more stable than xanthic acid. Both are readily oxidized, e.g., by iodine to disulphides, and can be estimated by iodometric titration. Qualitatively they are similar as collectors in flotation, although there are quantitative differences between them that may be important in practice. It is deduced that the influence of the nitrogen atom is subordinated to that of the sulphur atoms, and that the dominant group of these compounds is the mercapto group —SH or —5Na. The general method of investigation has been based on contact tests. Two temperatures, 10" and 35" C., have been chosen, and with a standard concentration of 20 mg. per liter of mercaptobenzthiazole (i.e., of the free acid) the influence of alkali, cyanide and copper sulphate on contact at sulphide mineral surfaces has been studied. This standard concentration corresponds to about 19 mg. per liter potassium ethyl xanthate; it brings out the differences between the minerals better than a higher concentra-

Jan 1, 1939

By George Gauci

INTRODUCTION The Broken Hill orebody was discovered in 1883. The richness of the deposit encouraged rapid development of the field and within fifteen years ten mining companies were operating. By 1940, several companies located in the centre of the field with limited reserves, had ceased operation. These leases have been acquired by Broken Hill South Limited and North Broken Hill Limited. The four companies currently operating in the field are, in order of increasing production rate:¬- Broken Hill South Limited (BH South) North Broken Hill Limited (North BH) The Zinc Corporation, Limited (ZC) and New Broken Hill Consolidated Limited (NBHC) The tonnages treated by each company since the present plants have been in operation are shown in Figure 1. The leases are located as shown in Figure 2, and an aerial view of Broken Hill showing the spread of the City on each side of the line of lode is shown in Figure 3. The present treatment plants date back to the early 1930's when the BH South plant was built. The North BH and ZC plants were built in 1939 and NBHC's in 1952. The three plants built before 1940 have similar crushing and grinding flowsheets. NBHC differs in that it includes rod mills with consequent differences in fine crushing equipment.

Jan 1, 1970

By Shigeki Nishimura

INTRODUCTION In this gapes, the author will describes to development of Yubari New coal mine. The construction set about since October 1970, and commenced from June 1975 in winning. Especially, descrives to compare with the studies at planning stage, and the experiences at under construction. The problems for development are next four: 1) There were no outcrop of the coal bearing strata, but the development was instituted against the deep coal seam occurrence at 800 m below the surface. 2) In order to the coal seams occured the deep level from the surface, threr had very difficult problems, i.e. temperature, earth pressure, methane etc. The countermeasure to solved them, were foundation of the development. 3) The construction was afflict with the inundation in high pressure, due to cement grouting and excavating alternately, overcame the difficulties. 4) The construction was finished by the encourage of national investment, in spite of the enterprise was weaken constitution from the energy revolution since 1960's. OUT LINE OF YUBARI NEW COAL MINE Geography Situation. Ishikari coal field is situated the west side of the Hidaka mountains, where runs north to south at center of Hokkaido, northern district of Japan. It's width is 40km in east and west, and length is 110km in north and south.

Jan 1, 1976

By Ian William Wark, Keith Leonard Sutherland

MERCAPTOBENZTHIAZOLE and its sodium salt are marketed under the trade names Flotagen and Flotagen S respectively, for use as collectors for cerussite and other minerals. The structural formulas for sodium mercaptobenzthiazole and for sodium ethyl xanthate are: [ ] Chemically there is a resemblance between the two compounds, though the free acid (mercaptobenzthiazole itself) is much more stable than xanthic acid. Both are readily oxidized, e.g., by iodine to disulphides, and can be estimated by iodometric titration. Qualitatively they are similar as collectors in flotation, although there are quantitative differences between them that may be important in practice. It is deduced that the influence of the nitrogen atom is subordinated to that of the sulphur atoms, and that the dominant group of these compounds is the mercapto group -SH or -SNa. The general method of investigation has been based on contact tests. Two temperatures, 10º and 35º C., have been chosen, and with a standard concentration of 20 mg. per liter of mercaptobenzthiazole (i.e., of the free acid) the influence of alkali, cyanide and copper sulphate on contact at sulphide mineral surfaces has been studied. This standard concentration corresponds to about 19 mg. per liter potassium ethyl xanthate; it brings out the differences between the minerals better than a higher concentra-

Jan 1, 1939

By Thomas F. Torries, George H. K. Schenck

Crushed and broken stone is used directly in construction as an aggregate and accounts for about half the value and two-fifths of the quantity of natural aggregates consumed in the United States. Sand and gravel provide most of the balance of aggregates except for some lightweight materials such as pumice and expanded shale. Conditions necessary for production of crushed stone from a deposit are : 1) Quality-should pass rigid specifications for strength and durability. 2) Cost-low average total delivered cost. Construction aggregates are hard, essentially inert materials suitable for being formed into a stable mass either (1) by the addition of cementing or binding materials that produce a concrete or (2) by compaction or by natural weight to produce a road base or foundation. Aggregates usually provide about 80 to 100% of the material volume of the construction masses in which they are used. The construction industry utilizes as aggregates about 70% of all crushed stone produced in the United States according to statistics provided by the U.S. Bureau of Mines (USBM) , [Table 1], using definitions as shown below. Nonconstruction uses of crushed stone, [Table 2], are included elsewhere in Industrial Minerals and Rocks because such uses require the special physical or chemical characteristics which are discussed in those chapters.

Jan 1, 1975

By James Gardner

IN 1923, Oklahoma took second place as an oil-producing state; whereas in 1922 it was the leader. California surpassed it, in 1923, by nearly 100,000,000 bbl. In 1923, Oklahoma produced, according to statistics of The Oil & Gas Journal, 165,013,685 bbl., or an increase of approximately 10 per cent. over the preceding year; the increase in California was approximately 90 per cent. The number of wells drilled in Oklahoma and the results of the two years are contrasted in the following table from data published in a preliminary bulletin by the U. S. Geological Survey. 1922 1923 Oil wells 4,149,68%. 3,515, 60% Gas wells 571, 9 %u 587, 11% Dry holes 1,428,23% 1,731,29% Total wells 6,148 5,833 The initial production from wells drilled in Oklahoma in 1923, according to The Oil & Gas Journal, was the largest in the history of the state, being 1,277,936 bbl. It has been 32 years since oil development began in the state, last year being the largest in the amount of production. The production of the past year would have been considerably greater were it not for the shutdown order in the Burbank field and curtailment of production in the Hewitt and Tonkawa pools.

Jan 3, 1924

By D. S. Kingery, D. W. Mitchell

Experience in Europe indicates that the control of dust production and dissemination by water or foam systems is not successful except during undercutting. Cybulski, Dawes, and DeBraaf-respectively Director, Mines Research Establishment "Barbara", Katowice, Poland; Principal Scientific Officer, Safety in Mines Research Establishment, Sheffield, England: and Chief, Central Mines Research Establishment, Hoensbroek, Treebeek, The Netherlands-believe that wetted dust becomes readily dispersible and abatement measures should be considered only as a temporary means for reducing the health hazard. In an effort to reduce the health hazard, calcium chloride is used on the floor of main haulageways in Dutch mines and water infusion is practiced in Germany in mines where the coal is relatively porous. With respect to wet coal dust, the Belgians, British, Dutch, French, and Russians reportedly have accepted the results of research from the Polish and American experimental mines on the effectiveness of water as an inert in arresting explosion propagation. The Polish use the two test methods proposed by the U.S. Bureau of Mines for evaluation of the adequacy of wetness of mine dust; they require that water be added to the wet dust to maintain a minimum of 50% moisture by weight if dependence is placed on water alone.

Jan 7, 1964

By William P. McConnell

At the dawning of the first century of AIME, mechanical handling of bulk materials was largely confined to movement of grain and light mill products by belt and screw conveyors, but grain handling experience inevitably led to the use of the belt conveyor for coal, ore and other heavier materials. In 1891, the first major U.S. conveyor installation for heavy minerals was completed at the Edison, N.J., plant of the New Jersey & Pennsylvania Concentrating Co. Functionally, this plant revealed its grain elevator heritage. Overlooked at the time of design or, perhaps more accurately, not fully recognized, were the dramatic differences between grain and minerals in both operating conditions of the system and the physical characteristics of the material to be conveyed. This inevitably caused problems, but from the ashes of these problems rose solutions. The Edison plant became a proving ground from which came two significant developments by Thomas Robins-the first conveyor belt designed specifically for impact loading and abrasive materials and the three-roll conveyor idler. As an installation with more than 50 conveyors in widths of 20-30 in. and belt centers of up to 500 ft, the plant was a landmark, for it established the belt conveyor as a vital method of trans- porting heavy, abrasive materials.

Jan 1, 1971

By James Cudworth

THE Birmingham district of Alabama has utilized the slag from its blast furnaces consistently since the earliest development of the slag industry. Today there are producers of slag cement who started business in 1900, and who have, under a progressive policy, expanded the number of their products to meet present demands. There are producers of slag aggregates and other crushed slag products who have been successful for periods of over thirty years. There are at the present two companies, Cheney Lime and Cement Co. and the Southern Cement Co., manu-facturing puzzolan cement; three companies, Birmingham Slag Co., Woodstock Slag Co., and Swann Chemical Co., making slag aggregates and by-products; one company, Tennessee Coal, Iron and Railway Co., a subsidiary of the U. S. Steel Corporation, producing ground open-hearth basic slag for soil conditioning. Two companies, the Sloss Sheffield Steel and Iron Co. and the Woodstock Slag Co., make slag concrete in ready-mix plants and one company, the Superock Company, manufactures fine and coarse slag aggregates under a new granulation process. No Portland cement is made with slag as an ingredient, because dolomite is used so extensively as a blast-furnace flux that the magnesium content of the slag is excessive.

Jan 1, 1937

By N. M. Raju, B. Singh

The paper seeks to present the results of experimentation in room and pillar stopes with different ground conditions to determine the safe working span. In the experimental stopes, ground movement was monitored with gradual widening of the room span. The field measurements included closure between the stope walls and the extent of ground movement in the hangwall using borehole extensometers. hock bolting was used as an exclusive support system which enabled introduction of scrapers for improving productivity. In one nine, phosphate bed, 3 to 3.5 m thick dipping at 45O and overlaid by weak laminated shale, was worked at shallow depth of cover. h the experimental panel, five s topes were worked with spans varying from 5.5 to 7 m. In the second mine, the chalcopyrite orebody up to 6 m in thickness dipping at 25 - 30" was worked at a depth of 1100 m. The hangwall consisted of fairly competent schistose rocks and therefore 10 to 15 m wide spans could be experimented. The field measurements confirmed that in the phosphate mine with weak shale roof, 7 m span could be safely worked with subsequent caving of the bolted roof. In the copper mine, 15 m span could be worked and the stopes required subsequent backfilling for better ground control.

Jan 1, 1983

By O. N. Carlson, K. E. Solie

The brittle-ductile transition temperatures of single and poly crystalline chromium metal were studied as a function of nitrogen concentration and chromium nitride distribution. It was observed that In recent years there has been an increasing interest in chromium-base alloys for high-temperature applications. The principal disadvantages, however, have been the difficulties of fabrication and the design problems associated with a material of such limited ductility. Various studies have been the effects noted in the poly crystalline material are essentially reversed in the single crystals. These observations are discussed in terms of existing theories for the brittleness of chromium. conducted recently directed toward a determination of the cause of this brittleness and to find ways for minimizing its effects. Allen et al.,' Wain Abrahamson and rant,' and weaver4 have carried out studies on the effects of interstitial impurities on the brittle-ductile transition of chromium metal of various degrees of purity. These investigations have shown that oxygen has little or no effect on the transition temperature of chromium in all conditions studied but that carbon increases the transition temperature under all conditions tested. Nitrogen was found to increase the transition temperature in the wrought condition and in the quenched or cast conditionS but reportedly has no effect in the furnace-cooled condition.

Jan 1, 1964