Search Documents

By Jr. D. C. Williams, D. V. Carter

The four new oil-field discoveries made in the East and East Central Texas districts during 1941 were the East Long Lake field, Anderson County; Pickering field, Shelby County; Pleasant Grove field, Rusk County, and Tri-Cities field, Henderson County. The discovery of oil production in the Pettit lime of the Lower Glen Rose was made in the Groesbeck (Barron) field in Limestone County and the Willow Springs field in Gregg County. Important extensions were made to the Pittsburg field, in Camp County, the Chapel Hill field, in Smith County, and the Hawkins field, in Wood County. The Hawkins field was extended sufficiently to more than double the number of proved surface acres. As usual the East Texas field led the district in the number of completions for the year. The second most active field during the year was the Hawkins field, with 250 new wells completed. The third most active was the Long Lake field, in which 50 wells were completed. Approximately 964 wells were completed in the district during 1941. Production and Probation The district is credited with having produced 163,566,695 bbl. of oil and distillate during the year. This represents a decrease of 4 per cent from the 170,424,685 bbl. of oil and distillate produced during the preceding year. The production of 130,378,620 bbl. of oil and distillate from the East Texas field represents 79.7 per cent of the total production of the district; that is, 6.3 per cent less than the production for the year 1940, The district had an estimated basic daily allowable of 614,982 bbl. of oil on Dec. 31. Approximately 33 per cent of the state's annual production was produced in the district, compared with 34.9 per cent for 1940. Since the majority of the fields in this district are subject to proration, any change in the annual production is attributable largely to changes in proration schedules and number of shutdown days. Fields subject to shutdown days were closed in for 113 days during the year, with the exception of the East Texas field, which was shut down 111 days. An order was promulgated by the Oil and Gas Division of the Texas Railroad Commission for encouraging the disposal of salt water and reservoir-pressure maintenance in the East Texas field. Discoveries Tex Harvey Oil Company'sNo. I S. E. J. Cartmel was completed as the discovery well for the East Long Lake field, Anderson County. Production was found in the Woodbine sand, the horizon from which the Long Lake field produces. The Pickering field, Shelby County, secures its production from the Nacatoch sand, found at an approximate depth of 1510 ft., in A. E. McKiernan's No. I, Pickering Lumbering Co. This field is in an area near the state line in which a number of relatively unimportant and

Jan 1, 1942

By Jr. D. C. Williams, D. V. Carter

The four new oil-field discoveries made in the East and East Central Texas districts during 1941 were the East Long Lake field, Anderson County; Pickering field, Shelby County; Pleasant Grove field, Rusk County, and Tri-Cities field, Henderson County. The discovery of oil production in the Pettit lime of the Lower Glen Rose was made in the Groesbeck (Barron) field in Limestone County and the Willow Springs field in Gregg County. Important extensions were made to the Pittsburg field, in Camp County, the Chapel Hill field, in Smith County, and the Hawkins field, in Wood County. The Hawkins field was extended sufficiently to more than double the number of proved surface acres. As usual the East Texas field led the district in the number of completions for the year. The second most active field during the year was the Hawkins field, with 250 new wells completed. The third most active was the Long Lake field, in which 50 wells were completed. Approximately 964 wells were completed in the district during 1941. Production and Probation The district is credited with having produced 163,566,695 bbl. of oil and distillate during the year. This represents a decrease of 4 per cent from the 170,424,685 bbl. of oil and distillate produced during the preceding year. The production of 130,378,620 bbl. of oil and distillate from the East Texas field represents 79.7 per cent of the total production of the district; that is, 6.3 per cent less than the production for the year 1940, The district had an estimated basic daily allowable of 614,982 bbl. of oil on Dec. 31. Approximately 33 per cent of the state's annual production was produced in the district, compared with 34.9 per cent for 1940. Since the majority of the fields in this district are subject to proration, any change in the annual production is attributable largely to changes in proration schedules and number of shutdown days. Fields subject to shutdown days were closed in for 113 days during the year, with the exception of the East Texas field, which was shut down 111 days. An order was promulgated by the Oil and Gas Division of the Texas Railroad Commission for encouraging the disposal of salt water and reservoir-pressure maintenance in the East Texas field. Discoveries Tex Harvey Oil Company'sNo. I S. E. J. Cartmel was completed as the discovery well for the East Long Lake field, Anderson County. Production was found in the Woodbine sand, the horizon from which the Long Lake field produces. The Pickering field, Shelby County, secures its production from the Nacatoch sand, found at an approximate depth of 1510 ft., in A. E. McKiernan's No. I, Pickering Lumbering Co. This field is in an area near the state line in which a number of relatively unimportant and

Jan 1, 1942

By Brooks J. Klimley, Daniel M. Higgins, Grover R. Castle

Measuring The Economic Viability Of Resource Projects (A Western Surface Coal Project) The bankers approach to the analysis of a new "green fields" mining project is similar but different from the approach that the pining company might take. The purpose of this paper shall be to discuss the techniques that are used by mining companies and bankers as they try to measure the economic viability of mining projects. The analysis of these new projects (by both the mining companies and the banker) is based on a projected revenue stream and not on historical earnings or past perfomance because these projects are start up situations with no history to look to. The starting point in the analysis of these projections is the choice of the assumptions to be used in preparing these projections. After the assumptions have been determined and the projections are prepared then the projections are submitted to various tests in order to determine whether the project measures up to previously agreed upon minimum standards. In order to illustrate the analytical procedures used in evaluating a mineral project the writer has constructed a hypothetical case involving the development of a western surface coal mine (Property). The basic data in connection with this hypothetical new project is described in the next section of this paper. After the Description of the Project is a section which shows the type of analysis that a mining company might prepare in order to approach a bank for a loan and the final section illustrates the type of analysis that a bank might prepare in evaluating this loan request. Description Of The Project or Basic Data In Connection With Undeveloped Western Surface Coal Property An independent mining/geological Consultant's report has been completed on the Property which confirms that the Property contains 175 million tons of economically recoverable coal subdivided into the following reserve categories in accordance with U.S. Bureau of Mines and U.S. Geological Survey definitions: Measured or Proven 90,000,000 Indicated or Probable 50,000,000 Inferred or Possible 35,000,000 The owners of the reserves have chosen to drill up those reserves that are nearest to the subcrop and have not spent as much time on those portions of the Property which are on the fringes of the deposit where the overburden is thicker because the stripping ratio and hence the operating costs and capital requirements are higher down dip. The proven reserves are based on an average thickness of 80 feet, of which a mining recovery of 90% is projected. The overburden thickness varies from 0' to 280' with an average thickness of 127'. The overburden consists mainly of scoria, sandstone, gravel, shale and silty clay. 134 holes were cored (and analysis done on five foot increments) in the measured reserve on the following spacing: 100 foot centers to define the burn line; 1,320 foot centers to define the early mining areas; 2,640 foot centers to identify the later mining areas.

Jan 1, 1985

By A. T. English

X-ray dif action techniques were used to investigate ordering and domain coalescence for the B2 (CsC1) superlattice in this alloy. Essentially complete disorder is obtainable by drastic quenching. isothertmal ordering occurs very rapidly at temperatures between 565° and 680°C, only a few seconds being required for development of substantial long-range order. A very fine antiphase dormain structure, found in samples annealed for short times, undergoes coalescence with further annealing. Domain "size" is found proportional to (t)1/2 . This Yate law can be derived by adapting the formalism of Hillert's analysis 01- metallurgical grain growth. For this Purpose the material is descvibed in terms of a "Swiss-cheese " structure, consisting of two multiply connected, mutually intertwined domain volumes. The observed activation enevgy for coalescence, 70 kcal per g-atom, agrees with an estit~lated value ,for volume diffusion in disordered rrzaterial. It is suggesled that the experimental value vejlects the substantially disordered environment of mobile vacancies located in the moving antiphase domain boundary. The alloy Fe-Co-2V is bcc below about 900'C and orders into a B2 (CsC1) superlattice below about 730c It has important applications in magnetic components, including many requiring extensive cold rolling.* example, Marcinkowski and Brown6 observed a re1atively small as-quenched domain size of about 250Å in B2 Fe3A1. Since there appear to be no published data on domain coalescence in B2 alloys, this process was studied in detail. MATERIALS AND EXPERIMENTAL TECHNIQUES A commercial high-purity alloy, nominally 49 Fe-49Co-2V, was obtained from the Arnold Engineering Co. in the form of cold-rolled sheet 0.004 in. thick. Samples were annealed for 1 hr at 800°C in dry H2 to produce disorder and quenched into iced brine. They were then annealed in a nitrate-nitrite salt bath for various times at temperatures between 525° and 625°C. Estimates of the LRO parameter S and the APD size D were made using established X-ray diffraction techniques. Superlattice peaks are best observed using CoKa radiation, for which the value of (fFe-fCo) is maximized. Peak-to-background intensity ratio was improved by filtering CoKß from the incident beam to eliminate sample fluorescence, and by using a pulse-height analyzer. The LRO parameter S was computed from the ratio of integrated intensities I 100/I 200- Owing presumably to systematic errors associated with the presence of crystallographic texture and X-ray extinction, only rough agreement was obtained between experimental and theoretical (absolute) intensity ratios. For this reason certain experimental refinements (e.g., use of balanced filters) were considered superfluous and were omitted. Emphasis was placed on maximizing intensity in order to reduce the time taken to accurately determine the contour of the very small (loo), peak. This was done by point counting 105 counts at appropriate intervals. Background intensity averaged about 1200 cps.

Jan 1, 1967

By Wilfrid R. Foster

The industrial importance of the sillimanite group of minerals depends upon the beneficial properties exhibited by porcelains and refractories in which substantial amounts of these minerals are utilized as raw materials. The presence of "sillimanite" (now known to be the closely related mineral, mullite) in conventional porcelains and refractories has been known since before the turn of the century. As early as 1906 German investigators observed a direct correlation between the "sillimanite" content of a porcelain and its electrical and mechanical properties. Acting upon this discovery, U. S. Bureau of Standards investigators during World War I developed improved pyrometer tubes and spark plug porcelains, by increasing substantially the amount of "sillimanite" at the expense of quartz. The success of these experiments, first reported in 1918, at once aroused a lively interest in the location of natural sources of sillimanite and its related minerals. As a result of diligent search, the large andalusite deposits in California were discovered in 1919. Within the next several years large deposits of kyanite and sillimanite in India and kyanite in the United States had been reported. The search for these minerals in quantity, by both private and governmental agencies, has continued unabated during the ensuing forty years. A number of domestic deposits of kyanite have been worked during the past 30 years. Of these, only the Virginian and South Carolinian deposits are currently in substantial production. The only commercial andalusite production in the United States has been in California and Nevada. A dumortierite deposit in Nevada, known since 1917 but ignored for want of a commercial use, began production in 1925. A topaz occurrence in South Carolina has yielded a small production since about 1940. Domestic production of andalusite, dumortierite and topaz had virtually ceased by 1950. There has never been any commercial development of domestic sillimanite deposits. Kyanite has been mined almost continuously in India since about 1922. The remoteness of the large deposits of Indian sillimanite had caused it to be neglected until 1949. In that year sillimanite production began, and it has continued to the present. South African andalusite has been marketed from the 1930's until the present time. From 1944 to 1955 Kenya, British East Africa, was an important producer of kyanite. Commercial deposits of kyanite in Ontario, Canada should soon be in production. The first production of kyanite in Europe began in Austria in 1953. No commercial deposits of mullite are known anywhere in the world. It is of interest to note that synthetic mullite, which as "sillimanite" first elicited interest in the A12O3-rich aluminosilicate refractories, has enjoyed a marked increase in production in recent years. This is a result of the gradual depletion of known deposits of high-quality kyanite and related minerals."' Composition The sillimanite group includes kyanite, andalusite, and sillimanite, all having the same chemical composition (A12O3•SiO2) but different physical properties. Two other minerals, dumortierite and topaz, are also included in

Jan 1, 1960

By David White

THE search for potash salts in the great "Red Beds? region of the Southwest, conducted for several years by the U. S. Geological Survey, the work being carried on for a part of the time in coöperation with the Bureau of Economic Geology and Technology of the University of Texas, has resulted in the discovery, within shafting depth, of potash salts, apparently of workable thickness and commercial quality, and prob-ably of great extent. Definite information is lacking as to the exact thickness of the potash beds, the size and boundaries of the areas underlain by workable strata, and the locations of the deposits richest and most favorably situated for exploitation. Briefly to review the salient features, of the general situation: We have in the great Red Beds region of the southwestern United States, embracing portions of central Kansas, western Oklahoma, eastern New Mexico, and northern and western Texas, .a series of sandstones. shales, anhydrite beds, clays and limestones, which; through an interval of 1000 ft., more or less, carry beds of salt, estimated by Darton1 to contain over 30,000 billions of tons of rock salt. It is the greatest known salt field of the world. At some points the intercalated beds of rock salt, one of which is reported by the driller to exceed 300 ft. in thickness, aggregate, accord-ing to the drillers' records, over 1000 ft. The sedi-mentary strata are similar in composition to those carrying the potash deposits of western Europe, and they were laid down at the same time and under condi-tions which, in many respects at least, were similar The stratigraphy and character of the beds are des-cribed by Darton2 and a, part of the area and the reported aggregate thicknesses of salt are shown, with some revision after Darton, in the accompanying map Fig. 1. The assumption that in the great areas of shallow evaporation basins spread over -the vast base-level region of saline deposition in the Southwest during Permo-Triassic time, potash salts were in some places, and at different stages, thrown down in crystalline deposits associated with the beds of rock salt, anhydrite, and gypsum, is, geologically speaking, more than reason-able. They are to be expected, and the conviction that they are probably present has long been held both in the Texas Bureau of Economic Geology and Tech-nology, under Dr. J. A. Udden, and in the- U. S. Geological Survey. Accordingly, for many years, efforts to determine whether potash deposits are present in this region have been made, though under very great difficulties, such as insufficient funds for boring, hack of drilling on private initiative in the more promising regions, hack of interest at first on the part of the drillers and companies, and, hater, inadequacy both of the methods of boring and of the sampling, to reveal in definite terms the thickness-of any saline stratum of given composition.

Jan 4, 1922

The San Manuel district of Arizona was first prospected prior to the Civil War, but there was little or no production until 1881. Small operators tried to develop ore bodies from time to time after that without success. Then, in 1917, a drilling program was carried out; but it did not indicate a copper content of interest. Finally, in the 1940s, the U. S. Geological Survey drilled the property and obtained indications of a mineralized area. At that time, Magma Copper and its principal owner, Newrnont Mining Corporation, drilled many deep holes through the gravels and conglomerates and in 1948 proved an ore reserve of 367 million tons of 0.785% copper sulfide ore. Underground exploration and development were started in early 1948, and in 1953 design and construction of the surface facilities commenced. By the end of 1955 plant construction was completed. The ore deposit of disseminated pyrite, chalcopyrite, chalcocite, molybdenite, silver, and gold is in quartz monzonite porphyry gangue. Mine production, which is entirely underground, is by full-gravity block-caving. Initially, ore mined at a rate of 36,000 tpd was hoisted through two identical shafts. From the 5,000 ton coarse ore bins located at the collar of each shaft, the ore was hauled by a shuttle service rail- road in 100-ton bottom-dump rail cars a distance of seven miles to the rail bin. Fragmentation from block-caving supplemented by underground grizzlies at the loading stations controlled the oversize material to give a feed size acceptable to the two 7 ft standard Syrnons crushers. During operation, however, it became evident that a large amount of secondary breaking in the grizzlies was necessary to produce a suitable feed for the standard crushers. The decision was then made to install primary gyratory crushers on the surface adjacent to the shaft site ore bins. Under each 5,000-ton coarse ore bin, an 8ft by 20 ft (2.44 m by 6. 1 m) apron feeder transfers the ore to a 13 ft 6 in. by 10 ft (4. 1 m by 3. 05 m) grizzly set at 6 in. (152 mm) and sloped at 45 degrees. About 65% of the ore passes the grizzly and thus bypasses the 42 in. by 65 in. (1.07 m by 1. 65 m) Allis -Chalmers gyratory equipped with a Hydroset mechanism and having an open side setting of 5 ½ in. (140 mm). Grizzly undersize and crushed ore drop onto a 6 ft by 30 ft (1. 83 m by 9. 14 m) variable- speed apron feeder for transfer to a 54 in. by 90 ft 5 in. (1.37 m by 27.6 m) inclined conveyor equipped with a tramp iron detector. Indication of tramp iron automatically stops the conveyor and both apron feeders. When the iron is removed from the belt by the operator,

Jan 1, 1978

The Climax Molybdenum Company' s newest operation is the Henderson project, which is located on the east side of the Continental Divide. Ore reserves are estimated at more than 300 million tons at a grade of 0.49% MoS2. For mining the ore a modified panel caving system is used. The ore is transported to the Henderson mill on the west side of the Continental Divide on a 42 in. (1.07 m) gauge railroad through 9.6 miles (15.4 km) of tunnel and 4. 8 miles (7.7 km) of surface track, a total distance of 14.4 miles (23. 2 km). Each train consists of 30 ore cars with capacity of 22 st (20 mt) of ore or 660 st (599 mt) per train. The unmanned trains operate completely automatically. At the 54 in. by 84 in. primary gyratory crusher, the bottom dump ore cars pass over a dump scroll to discharge at a maximum rate of 100 st (91 mt) per minute. Dumped ore falls onto a rock box before passing over a 17 ft long by 46 ft wide (5. 2 m by 14 m) grizzly set at a 40° angle with bar spacings of 7 ½ and 8 ½ in. (191 mm and 216 mm) openings. An estimated 30 to 50% of the ore (which at times is wet and sticky) passes through the grizzly. The operators report that a shallower angle on the grizzly, perhaps 35º to 37º, would have been sufficient and would have prevented impact on the back of the crusher pocket by large boulders. This pocket as well as the crushed ore pocket under the crusher is lined with AR plate. The accompanying drawings show a "future splitter" and the operators are planning the installation of this unit to prevent impact and subsequent damage to the crusher spider. Crushed ore at an 8 to 9 in. (203 mm to 229 mm) size joins the grizzly undersize in the pocket beneath the crusher. This pocket is sized at 660 live st (599 mt) so that it will accept an entire trainload of ore. Crushed ore is removed from the pocket by a four-speed, 84 in. (2. 1 m) apron feeder operating at 9.6 to 29. 3 fpm (2.9 to 8.9 mpm). A 60 in. (1.5 m) takeaway conveyor operating at 480 fpm (146 mpm) delivers the crushed ore to a 58,000 st live and 193,000 st total (52,600 and 175, 100 mt) open stockpile under an A -frame supported tripper gallery. Impact idlers on the takeaway conveyor under the apron feeder discharge are mounted on wood blocks for a cushioning effect and ripped belt detecting bars are located behind each impact idler. The conveyor tunnel is of corrugated and galvanized steel construction rather than concrete. The concrete crusher enclosure is circular in design from its lowest level at elevation minus 110 ft 4 in. (minus 33. 6 m) to elevation

Jan 1, 1978

By C. B. Dudley

bas shown us that the railroads of this country can save several milt liohs a par by adopting uniform rail sections, and as unfortunately for him, he cannot patent his idea, it only remains for the railroads to adopt it, and to thank him for his payer. Dr. C. B. Dudley, Altoona, Pa. : 111 rising to close this interestin~ discussion, I want, in the first place, to thank every one who has contributed to it for his full and open criticism. The work tvhich has been done on steel rails, and which has been diwu&e,l here Juring thee two days, was not done to establish any pet theories, nor to make out that any person was great or any person small, but with a sincere desire to get at what is the truth in regard to the wedring capacity of steel rails. There are enormous commercial coneiderations invoIved in this question, and, as I look at the matter, the more honest criticism and fair discussion there is, the Inore likely it is that the truth will appear. Ad first I would like to say that it seems to me very little has been said here upon the main conclusion of the paper, namely, that the softer rails give the better wear. All sorts of side issues have been discussed; but this poiat, which is really the principal one at issue, has been largely ignored, aid I cannot But feel that it still remains unshaken. Witb regard to ohemists end chemical work, there has been considerable said tending to throw discredib on chemists and their work; and while I believe that there have been in the past, are now, and may be in the futnre, a good many poor chemical analyses made, X also believe that chemists are, as a rule, as honest and competent as gentlemen who belong to other professiomc. There are chemisb who are chemists, and who are not chemists. The determination of -manganese has bee* called in question. Now I think the chemist at almost every steel works in the country will tell you that, in his experience, the manganese diffe1.s in different parts of the same ingot. Mr. T. T. Morrell, chemist of the Camhria Iron Company, whom I believe to be s thoroughly competent and hone6t chemist, tells me that he has often found different amounts of manganese in different parts of the same ingot. Come with me to Altoona, and I will take you into the machine shop where steel is king cut aud shaped, and I will show you that it is often necessary to stop the lathe or planer and take a cold chisel to cut oat a hard spot, or else ntn the risk of breaking the tool. This hard spot is simply a pttrt of the syiegel which was not thoraughiy mixed with the ma

Jan 1, 1881

By Edward Sampson, Allan B. Griggs

Surveying of many holes drilled by the U. S. Bureau of Mines in the Metaline district has shown surprising deviations. The holes start in the Ledbetter slate (Ordovician) and pass into the underlying gently dipping Metaline limestone (Cambrian) at varying depths, locally in excess of 1000 it. All holes start vertical, but one had deflected as much as 35° at a depth of only 300 it. One hole was found to be deflected 70' at a depth of 1000 ft. These deviations were not indicated to the drillers by any action of the rods or machines. Analysis of the survey data in the light of the observed geology indicates that the holes deviate most in the Ledbetter slate and scarcely at all in the Metaline limestone. The upper part of the "limestone'" in most holes is a massive rock strongly altered by hydrothermal action and essentially homogeneous. The slate is only obscurely bedded but has a cleavage, varying from slight to strong, which is unrelated to bedding. Drill holes have deflected to become nearly perpendicular to the cleavage. Several plans and cross sections are submitted showing the behavior of various holes. Introduction The Metaline district of northeastern Washington has received much attention recently and has promise of becoming even more important as a source of zinc than at present. Exploration has been conducted largely by deep diamond drilling, and in the course of this work it was found that holes became seriously deflected. This paper deals with the nature and causes of these deflections. The district lies along the Pend Oreille River in the northeastern corner of Washington, about loo miles north of Spokane, 9 miles from British Columbia, and 15 miles from Idaho. Three mines are now in operation and for a number of years have furnished a considerable production of zinc and lead. The ore contains zinc and lead in a ratio of about 31/2 to I, and occurs in the upper part of the Metaline limestone of Cambrian age, the upper member of which, where unaltered, is a rather pure limestone. This is overlain by Ledbetter slate of Ordovician age. Ore has formed by replacement of limestone, commonly 100 to 200 ft. below the slate, in areas of gentle dip, resulting in extensive tabular ore bodies. In and near ore, limestone has been intensely altered to granular dolomite and fine-grained quartz, which, where it predominates, forms "jasperoid." As part of their war program, the Geological survey and Bureau of Mines of the U. S. Department of Interior have been cooperating in an investigation of the district. The exploration by the Bureau of Mines in 1943 and 1944 was conducted largely by deep diamond drilling in which as much as 1000 ft. or more of Ledbetter slate was penetrated before the ore-bearing Metalin-2 limestone was reached. During the course of this drilling it was found that holes were seriously deflected while traversing the Ledbetter slate.

Jan 1, 1949

By Edward Sampson, Allan B. Griggs

Surveying of many holes drilled by the U. S. Bureau of Mines in the Metaline district has shown surprising deviations. The holes start in the Ledbetter slate (Ordovician) and pass into the underlying gently dipping Metaline limestone (Cambrian) at varying depths, locally in excess of 1000 it. All holes start vertical, but one had deflected as much as 35° at a depth of only 300 it. One hole was found to be deflected 70' at a depth of 1000 ft. These deviations were not indicated to the drillers by any action of the rods or machines. Analysis of the survey data in the light of the observed geology indicates that the holes deviate most in the Ledbetter slate and scarcely at all in the Metaline limestone. The upper part of the "limestone'" in most holes is a massive rock strongly altered by hydrothermal action and essentially homogeneous. The slate is only obscurely bedded but has a cleavage, varying from slight to strong, which is unrelated to bedding. Drill holes have deflected to become nearly perpendicular to the cleavage. Several plans and cross sections are submitted showing the behavior of various holes. Introduction The Metaline district of northeastern Washington has received much attention recently and has promise of becoming even more important as a source of zinc than at present. Exploration has been conducted largely by deep diamond drilling, and in the course of this work it was found that holes became seriously deflected. This paper deals with the nature and causes of these deflections. The district lies along the Pend Oreille River in the northeastern corner of Washington, about loo miles north of Spokane, 9 miles from British Columbia, and 15 miles from Idaho. Three mines are now in operation and for a number of years have furnished a considerable production of zinc and lead. The ore contains zinc and lead in a ratio of about 31/2 to I, and occurs in the upper part of the Metaline limestone of Cambrian age, the upper member of which, where unaltered, is a rather pure limestone. This is overlain by Ledbetter slate of Ordovician age. Ore has formed by replacement of limestone, commonly 100 to 200 ft. below the slate, in areas of gentle dip, resulting in extensive tabular ore bodies. In and near ore, limestone has been intensely altered to granular dolomite and fine-grained quartz, which, where it predominates, forms "jasperoid." As part of their war program, the Geological survey and Bureau of Mines of the U. S. Department of Interior have been cooperating in an investigation of the district. The exploration by the Bureau of Mines in 1943 and 1944 was conducted largely by deep diamond drilling in which as much as 1000 ft. or more of Ledbetter slate was penetrated before the ore-bearing Metalin-2 limestone was reached. During the course of this drilling it was found that holes were seriously deflected while traversing the Ledbetter slate.

Jan 1, 1949

By Maurice Rey, H. Beavers

THROUGH circumstances connected with the war, the senior author lost his records, therefore it has been impossible to include numerical data in this paper. The arsenical quicksilver ore investigated had been roasted, with poor metallurgical results. The vapor-tension temperature curves of mercury and arsenious trioxide are similar, and the arsenical compound hampers the coalescence of mercury drops in the condenser and is the cause of large stack losses. The ore was a gray limestone carrying small amounts of carbon and mineralized with cinnabar and two arsenic minerals, realgar (As2S2) and arsenopyrite (FeAsS). The proportion of realgar often exceeded that of cinnabar; the proportion of arsenopyrite was smaller. The grade of the ore varied between 0.8 and 4 per cent Hg. The problem was to make a high-grade mercury concentrate, as free from arsenic as possible. The water used throughout the testing was hard, having a pH of about 8. FLOTATION OF REALGAR Realgar showed a very strong tendency to float. It formed a film at the surface of the pulp and floated in abundance with only pine oil. Therefore an attempt was made to float the realgar before the cinnabar, but this was not very successful; the percentage of mercury in the realgar concentrate could never be brought below 2 or 3 per cent. Cinnabar slimed easily and floated with pine oil, so that some of it always accompanied the realgar. There was also the question of the cinnabar-arsenopyrite separation. On further investigation it was found that realgar can be floated not only with pine oil but even better with a combination of hydrocarbons and pine oil. Washing the ore with ether revealed that it contained hydrocarbons, which helped to float the realgar. In this connection it belongs to the same class as carbon, sulphur and talc. It can be floated also with a xanthate, when activated by a heavy-metal salt. The conditions favoring the two types of flotation are opposed, as activation by a copper salt facilitates xanthate flotation (in fact, is even necessary to it), whereas it hinders pine oil and petroleum flotation. One type of flotation can be termed nonpolar and the other polar, a distinction that has been stressed in a previous paper.1 DEPRESSION OF REALGAR AND FLOTATION OF CINNABAR 'Many chemicals were tested in an attempt to float the cinnabar and depress the realgar. Finally starch rendered soluble with caustic soda was tried, also several grades of commercial soluble starch, and dextrin was found to be the best and the most convenient reagent. Several of these starch preparations have a strong flocculating effect on the pulp, which is a distinct disadvantage. Dextrin, with its low flocculating power, is excellent. It is noteworthy that starch preparations are also depressants for carbon and talc, so that the fact apparently has a general

Jan 1, 1941

By R. H. Tien

The accuracy of the method of steady-state approximation applied to the problems of heat transfer involving phase change (London and Seban's solution) is improved by defining a "modified heat of fusion" which accounts for the effect of specific heat. An analytical expression for this modified heat of fusion is derived in terms of the actual heat of fusion, specific heat, and surface temperature. Numerical solution for the freezing of iron indicates that the ratio of the modified heat of fusion to the actual heat of fusion increases from 1.04 to 1.4 as the surface temperature decreases from 2700° to 1600°F. The heat transfer process accompanying solidification is complicated owing to the moving solid-liquid interface where the latent heat of fusion is released. Exact analytical solution is available only for a few special cases of freezing problems such as Stefan's1 problem. In a commonly used steady-state approximation method, London and seban's2 solution, the effect of specific heat is neglected. This approximation, however, may introduce some degree of error in mathematical analysis when the temperature of the solid surface is much lower than the freezing temperature, as in the case of freezing metals. In a recent work by Robertson and Schenck,3 the problem of freezing a semi-infinite region with finite surface conductance was programed in a digital computer through the finite difference method. A family of curves for the correction of the London-Seban solution was given in a dimensionless plot for different ratios of heat of fusion and specific heat effect; it was shown that the London-Seban solution when applied to the freezing of a mild steel slab under some particular conditions gave results in error by about 10 pct in the solidification rate. Although the Robertson-Schenck computer result has improved the London-Seban solution to a great extent, lack of generality and the tedious computing procedure have restricted its application. In this paper a "modified heat of fusion" which accounts for the effect of specific heat is defined, and is used instead of the actual heat of fusion in the London-Seban solution. An analytical expression of this modified heat of fusion in terms of the specific heat, surface temperature, and actual heat of fusion is derived by comparing the solutions of Stefan and London-Seban for the case of freezing of a semi-infinite region with constant surface temperature. It can also be extended to the case with finite surface conductance, and the results show good agreement with the Robertson-Schenck computer solution. The expression of the modified heat of fusion, the accuracy of the London-Seban solution, and the temperature distribution within the solid are presented graphically in dimensionless form. Numerical solution for the freezing of iron indicates that the ratio of the modified heat of fusion to the actual heat of fusion increases from 1.04 to 1.40 as the surface temperature decreases from 2700° to 1600°F.

Jan 1, 1969

By G. W. Healy, J. C. Schottmiller

Molten silicates were found to exist in the Cr-Si-0 system at temperatures above 1450°C. one atom of oxygen is readily removed from CrzOs in the presence of Si02 at 1700°C, forming a silicate melt. Steam-hydrogen ratio measurements made at this temperature indicate that the free energy of the reaction: Cr20s(c) + Hz = 2CrO (in Si02 -saturated melt) + H20 is approximately 5600 * 1500 cal. A deep-blue chromous silicate, probably Cr2Si04, forms from these melts at about 1400" to 1500°C, and is characterized by.its distinctive X-ray diffraction pattern and optical properties—distinct pleochroism and high refractive indices. THE question of the state of oxidation of chromium in slags has vexed metallurgists for many years The experiments of Koerber and Oelsenl suggested the probable presence of divalent chromium in silica-saturated slags equilibrated with high-chromium melts. Hilty and coworkers2 had also found chromium at lower valency, as Cr304, in inclusions formed from oxygen-saturated Fe-Cr melts with as little as 10 pct Cr. In both cases, disproportiona-tion of the lower oxide to CraO3 and chromium was found to occur to a greater or lesser extent, depending upon the rate of cooling from the high temperature. The work on Cr304 was sufficiently detailed for chipmans to derive its thermodynamic properties, but Oelsen's experiments in the silicate system were not extensive enough since most of his runs were made with slags containing large amounts of manganese oxide in addition to iron and chrome oxide and silica. The present study describes experiments carried out to map out an approximate liquidus diagram in the CrzOs, "CrO", SiOa portion of the Cr-Si-0 system, and to measure the partial free energy of solution of oxygen in the system. EXPERIMENTAL 1) Approximate Melting-Point Determinations. Preliminary trials showed that when an equimolar mixture of Cr20s and SiOa was treated with hydrogen in the temperature range 1500" to 1600°C, copious amounts of steam were evolved, and a low-melting liquid formed which could be quenched to a blue, crystalline, material having a distinctive X-ray diffraction pattern. It was found that the identical material could be produced by heating intimately mixed, finely divided Cra03, Cr, and SiOa, held in a tungsten crucible, under purified argon. Thus, it was possible to prepare mixtures containing any desired proportions of chromium, silicon, and oxygen, pel-letize them, heat to temperature in the furnace shown in Fig. 1, and observe, after cooling, whether the pellet remained unchanged or showed signs of incipient, partial, or complete melting. 2) Free Energy of Solution of Oxygen. This was studied by measurement of steam-hydrogen ratios for the reaction: H20 (gas) + O (dissolved in charge) + Ha (gas) The experimental method chosen was to prepare a

Jan 1, 1964

By Louis Moyd

The Concrete Research Division, U.S. Corps of Engineers, has developed a simple procedure for determining the coefficients of linear thermal expansion of rocks by means of resistance wire (SR-4) strain gauges. Gauges are cemented to the surfaces of specimens, which are then brought alternately to temperatures of 35OF and 1350F. Results are accurate to the seventh decimal place. IN the course of investigations of the thermal properties of various rocks proposed for use as aggregates in concrete structures, a relatively rapid method of determining coefficients of linear thermal expansion was required. A method which proved to be satisfactory for this purpose was developed in the petrographic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss. The method is based on the fact that strain effects in a specimen can be determined by measuring variations in the resistance of an electrical conductor firmly cemented to the surface of the specimen. Equipment for the determination of strain, electrically, has been developed by the Baldwin-South-wark Division of the Baldwin Locomotive Works in Philadelphia. This equipment includes small strain gauges made of coils of resistance wire bonded between thin sheets of paper (SR-4 gauges), and a portable "Strain Indicator" which records variations in the length of the gauges in microinches per inch. Gauges of this type are now in general use for determinations of various mechanically-induced strains, but their use for the determination of coefficients of thermal expansion appears to be a new application. The advantages of the method are that the test specimens may be relatively small and require only a minor amount of preparation, that a large number of tests can be run at the same time, and that the installation and operation of the equipment is relatively simple. The method and equipment described are now in regular use for determining the coefficients of linear thermal expansion of rock samples submitted to this laboratory. Rocks which have been tested include granites, syenites, gabbros, and other igneous rocks, limestones and dolomitic limestones, sandstones, and quartzites. Specimen Preparation: To standardize the conditions of the tests, the rock specimens are sliced by diamond saw into slabs about 11/2x11/4 in. In the case of bedded or foliated rocks, three oriented slabs are cut from the same specimen, and represent, respectively, a direction in a plane of the bedding or foliation of the rock; a direction along the bedding or foliation and at a right angle to the first; and a direction across the planes of bedding or foliation. One of the large surfaces of each slab is lapped for a few minutes with No. 100 abrasive powder to remove saw scars and irregularities. The slabs are soaked in petroleum ether and then dried in an oven to remove all traces of oil picked up in the sawing

Jan 1, 1951

By Louis Moyd

The Concrete Research Division, U.S. Corps of Engineers, has developed a simple procedure for determining the coefficients of linear thermal expansion of rocks by means of resistance wire (SR-4) strain gauges. Gauges are cemented to the surfaces of specimens, which are then brought alternately to temperatures of 35OF and 1350F. Results are accurate to the seventh decimal place. IN the course of investigations of the thermal properties of various rocks proposed for use as aggregates in concrete structures, a relatively rapid method of determining coefficients of linear thermal expansion was required. A method which proved to be satisfactory for this purpose was developed in the petrographic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss. The method is based on the fact that strain effects in a specimen can be determined by measuring variations in the resistance of an electrical conductor firmly cemented to the surface of the specimen. Equipment for the determination of strain, electrically, has been developed by the Baldwin-South-wark Division of the Baldwin Locomotive Works in Philadelphia. This equipment includes small strain gauges made of coils of resistance wire bonded between thin sheets of paper (SR-4 gauges), and a portable "Strain Indicator" which records variations in the length of the gauges in microinches per inch. Gauges of this type are now in general use for determinations of various mechanically-induced strains, but their use for the determination of coefficients of thermal expansion appears to be a new application. The advantages of the method are that the test specimens may be relatively small and require only a minor amount of preparation, that a large number of tests can be run at the same time, and that the installation and operation of the equipment is relatively simple. The method and equipment described are now in regular use for determining the coefficients of linear thermal expansion of rock samples submitted to this laboratory. Rocks which have been tested include granites, syenites, gabbros, and other igneous rocks, limestones and dolomitic limestones, sandstones, and quartzites. Specimen Preparation: To standardize the conditions of the tests, the rock specimens are sliced by diamond saw into slabs about 11/2x11/4 in. In the case of bedded or foliated rocks, three oriented slabs are cut from the same specimen, and represent, respectively, a direction in a plane of the bedding or foliation of the rock; a direction along the bedding or foliation and at a right angle to the first; and a direction across the planes of bedding or foliation. One of the large surfaces of each slab is lapped for a few minutes with No. 100 abrasive powder to remove saw scars and irregularities. The slabs are soaked in petroleum ether and then dried in an oven to remove all traces of oil picked up in the sawing

Jan 1, 1951

By Maurice Rey, H. Brevers

THROUGH circumstances connected with the war, the senior author lost his records therefore it has been impossible to include numerical data in this paper. The arsenical quicksilver ore investigated had been roasted, with poor metallurgical results. The vapor-tension temperature curves of mercury and arsenious trioxide are similar, and the arsenical compound hampers the coalescence of mercury drops in the condenser and is the cause of large stack losses. The ore was a gray limestone carrying small amounts of carbon and mineralized with cinnabar and two arsenic minerals, realgar (As2S2) and arsenopyrite (FeAsS). The proportion of realgar often exceeded that of cinnabar; the proportion of arsenopyrite was smaller. The grade of the ore varied between 0.8 and 4 per cent Hg. The problem was to make a high-grade mercury concentrate, as free from arsenic as possible. The water used throughout the testing was hard, having a pH- of about 8. FLOTATION OF REALGAR Realgar showed a very strong tendency to float. It formed a film at the surface of the pulp and floated in abundance with only pine oil. Therefore an attempt was made to float the realgar before the cinnabar, but this was not very successful; the percentage of mercury in the realgar concentrate could never be brought below 2 or 3 per cent. Cinnabar slimed easily and floated with pine oil, so that some of it always accompanied the realgar. There was also the question of the cinnabar-arsenopyrite separation. On further investigation it was found that realgar can be floated not only with pine oil but even better with a combination of hydrocarbons and pine oil. Washing the ore with ether revealed that it contained hydrocarbons, which helped to float the realgar. In this connection it belongs to the same class as carbon, sulphur and talc. It can be floated also with a xanthate, when activated by a heavy-metal salt. The conditions favoring the two types of flotation are opposed, as activation by a copper salt facilitates xanthate flotation (in fact, is even necessary to it), whereas it hinders pine oil and petroleum flotation. One type of flotation can be termed nonpolar and the other polar, a distinction that has been stressed in a previous paper. DEPRESSION OF REALGAR AND FLOTATION OF CINNABAR Many chemicals were tested in an attempt to float the cinnabar and depress the realgar. Finally starch rendered soluble with caustic soda was tried, also several grades of commercial soluble starch, and dextrin was found to be the best and the most convenient reagent. Several of these starch preparations have a strong flocculating effect on the pulp, which is a distinct disadvantage. Dextrin, with its low flocculating power, is excellent. It is noteworthy that starch preparations are also depressants for carbon and talc, so that the fact apparently has a general

Jan 1, 1941

By H. Brevers, Maurice Rey

Through circumstances connected with the war, the senior author lost his records, therefore it has been impossible to include numerical data in this paper. The arsenical quicksilver ore investigated had been roasted, with poor metallurgical results. The vapor-tension temperature curves of mercury and arsenious trioxide are similar, and the arsenical compound hampers the coalescence of mercury drops in the condenser and is the cause of large stack losses. The ore was a gray limestone carrying small amounts of carbon and mineralized with cinnabar and two arsenic minerals, realgar (As2S2) and arsenopyrite (FeAsS). The proportion of realgar often exceeded that of cinnabar; the proportion of arsenopyrite was smaller. The grade of the ore varied between 0.8 and 4 per cent Hg. The problem was to make a high-grade mercury concentrate, as free from arsenic as possible. The water used throughout the testing was hard, having a pH of about 8. Flotation of Realgar Realgar showed a very strong tendency to float. It formed a film at the surface of the pulp and floated in abundance with only pine oil. Therefore an attempt was made to float the realgar before the cinnabar, but this was not very successful; the percentage of mercury in the realgar concentrate could never be brought below 2 or 3 per cent. Cinnabar slimed easily and floated with pine oil, so that some of it always accompanied the realgar. There was also the question of the cinnabar-arseno-pyrite separation. On further investigation it was found that realgar can be floated not only with pine oil but even better with a combination of hydrocarbons and pine oil. Washing the ore with ether revealed that it contained hydrocarbons, which helped to float the realgar. In this connection it belongs to the same class as carbon, sulphur and talc. It can be floated also with a xanthate, when activated by a heavy-metal salt. The conditions favoring the two types of flotation are opposed, as activation by a copper salt facilitates xanthate flotation (in fact, is even necessary to it), whereas it hinders pine oil and petroleum flotation. One type of flotation can be termed non-polar and the other polar, a distinction that has been stressed in a previous paper.' Depression of Realgar and Flotation of Cinnabar Many chemicals were tested in an attempt to float the cinnabar and depress the realgar. Finally starch rendered soluble with caustic soda was tried, also several grades of commercial soluble starch, and dextrin was found to be the best and the most convenient reagent. Several of these starch preparations have a strong flocculating effect on the pulp, which is a distinct disadvantage. Dextrin, with its low flocculating power, is excellent. It is noteworthy that starch preparations are also depressants for carbon and talc, so that the fact apparently has a general

Jan 1, 1943

By Maurice Rey, H. Brevers

Through circumstances connected with the war, the senior author lost his records, therefore it has been impossible to include numerical data in this paper. The arsenical quicksilver ore investigated had been roasted, with poor metallurgical results. The vapor-tension temperature curves of mercury and arsenious trioxide are similar, and the arsenical compound hampers the coalescence of mercury drops in the condenser and is the cause of large stack losses. The ore was a gray limestone carrying small amounts of carbon and mineralized with cinnabar and two arsenic minerals, realgar (As2S2) and arsenopyrite (FeAsS). The proportion of realgar often exceeded that of cinnabar; the proportion of arsenopyrite was smaller. The grade of the ore varied between 0.8 and 4 per cent Hg. The problem was to make a high-grade mercury concentrate, as free from arsenic as possible. The water used throughout the testing was hard, having a pH of about 8. Flotation of Realgar Realgar showed a very strong tendency to float. It formed a film at the surface of the pulp and floated in abundance with only pine oil. Therefore an attempt was made to float the realgar before the cinnabar, but this was not very successful; the percentage of mercury in the realgar concentrate could never be brought below 2 or 3 per cent. Cinnabar slimed easily and floated with pine oil, so that some of it always accompanied the realgar. There was also the question of the cinnabar-arseno-pyrite separation. On further investigation it was found that realgar can be floated not only with pine oil but even better with a combination of hydrocarbons and pine oil. Washing the ore with ether revealed that it contained hydrocarbons, which helped to float the realgar. In this connection it belongs to the same class as carbon, sulphur and talc. It can be floated also with a xanthate, when activated by a heavy-metal salt. The conditions favoring the two types of flotation are opposed, as activation by a copper salt facilitates xanthate flotation (in fact, is even necessary to it), whereas it hinders pine oil and petroleum flotation. One type of flotation can be termed non-polar and the other polar, a distinction that has been stressed in a previous paper.' Depression of Realgar and Flotation of Cinnabar Many chemicals were tested in an attempt to float the cinnabar and depress the realgar. Finally starch rendered soluble with caustic soda was tried, also several grades of commercial soluble starch, and dextrin was found to be the best and the most convenient reagent. Several of these starch preparations have a strong flocculating effect on the pulp, which is a distinct disadvantage. Dextrin, with its low flocculating power, is excellent. It is noteworthy that starch preparations are also depressants for carbon and talc, so that the fact apparently has a general

Jan 1, 1943

By Paul Averitt

require both time and money. Any attempt to secure a quick answer will yield a figure that very likely cannot be substantiated, and certainly will not yield information in the detailed form now desired. It will be about 10 years before a completely new estimate can be prepared for the coal reserves of the United States at our present rate of progress, though of course, much information will be available in the interim. We would like to present such information as we obtain in the form most acceptable to the industry, and to that end we are working closely with coal resource committees of the AIME, the National Bituminous Coal Advisory Council, and the Bureau of Mines. DISCUSSION G. H. Cady*—Mr. Averitt's description of the nature of the coal resources investigations of the United States Geological Survey and the progress of this work is very timely in view of the general interest in the subject of coal resources. The Federal Survey is obviously taking the "long view" with respect to the appraisal of the coal resources as part of the preparation of the general geological map of the country and the attendant determination of the quantity of all mineral and fuel resources. It is apparently for regional surveys of the conventional type that the detailed procedures employed by the Federal Survey are applicable. Even if so it is somewhat unexpected to find the same criteria for evaluation will be applied to the country as a whole. The work on coal resources appraisal has been proceeding at various rates in a number of coal producing states for various periods. Undoubtedly since there has been no common practice in the method of appraisal the states each have worked independently and independently of the Federal Survey, and each has adopted certain practices to meet local conditions. I do not know how much consideration has been given by the U. S. Geological Survey to these practices. It seems probable that such consideration might result in important modifications of the standards which apparently have been set up by the Federal group in line with local requirements. It is the practice in some state surveys to present the facts in regard to the occurrence and distribution of coal beds and their variations in thickness down to thicknesses of 1 to 1 1/2 ft in relatively narrow stages up to maximum thickness. It is then possible for any one using such figures to compile quantitative estimates of workable coal at various minimum thickness limits. This is a desirable objective where surveys are detailed and information correspondingIy good. However, vast quantities of coal lie in beds that are relatively thin about which little information is available and the quantity of such coal might affect the final appraisal to the extent of several thousand million, depending upon the minimum limitation observed. Thus in the case of Illinois a difference of 1 ft in average thickness of coal in the coal field would make a difference of approximately 35 billion tons in the estimated quantity present. One is dealing with a very large area and small differences in thicknesses are very irnportant in the overall picture. The estimate of 10 years to accomplish the sort of detailed appraisal outlined by Mr. Averitt is viewed somewhat skeptically and certainly would require many more trained geologists than seem to be available. The requisite detailed mapping and study are very time consuming not only because of the geological field work required, which is difficult in certain seasons, but also in order to assemble data from company and personal files, and to study drill records and cores, and to sample and analyze the coal. Unless the staff of geologists could be increased in the order of several hundred per cent the prospects are that the appraisal of the type suggested will require many decades not just one. The permanent value of such appraisal, however, is not questioned and it should be expedited as rapidly as means allow. Satisfactory appraisal is not easily achieved and will vary from time to time. The main function of a geological survey is to collect and present the facts that will make possible appraisal in terms of existing conditions by individuals, particularly engineers, qualified by training and expcrience for making such estimates. Thickness and character of the coal bed, nature of the overlying and underlying strata, position, thickness, and character of "partings," relationship to other coal beds, and a variety of other factors must be assembled by the geologist in order to present a complete picture of the geological setting. The economic and engineering factors are in general outside the field of geological experience. The geologist should see to it that the pertinent geological facts are available; much more information than simply thickness and depth of the coal beds is essential to meet all the requirements of appraisal in the future as well as at present. With respect to the present demand by engineers and coal mine operators and others for a rapid re-appraisal of the available coal resources, in the light of existing practices and those in immediate prospect, the Federal procedure of systematic mapping and appraisal is scarcely in line. It will be necessary for those particularly interested in having such an estimate made to establish standards with respect to the various factors involved so that the scope of the geological work can be definitely restricted for the various coal fields. There is little use in setting up general standards since no such standards will be applicable to all fields. Thus it is folly to establish a standard minimum thickness to be generally applicable which is one-half to one-third the minimum minable thickness in some fields. The greatest difficulty in appraisal of the presently actually workable coal bed lies in the variation in the importance placed on roof, floor, structural conditions, bedded impurities. sulphur content and other factors that affect judgment relative to the value of a coal bed. It is doubtful whether any appraisal will have universal approval in view of the variable factors involved. For this reason if none other, the facts should be carefully and painstakingly assembled after the manner of a systematic geological survey such as that advocated by Mr. Averitt. Only upon the basis of sucb information can reliable estimates be made in line with selected conditions. Paul AveRitt (author's repty)— In this paper I discussed, but did not define as such, two major phases of our activities on coal, which are closely related, and which normally we in the U. S. Geological Survey see as an integrated whole. It is understandable, therefore, that Dr. Cady should assume that my remarks applied only to the current work on coal reserves with which I am directly concerned. In view of Dr. Cady's discussion, however, I think a brief summary of the two phases of U. S. Geological Survey activities on coal will be appropriate. The long-term function of the U. S. Geological Survey on coal investigations is to make detailed geologic studies, involving the preparation of detailed geologic maps showing the outcrops and correlations of coal beds, direction and dip of coal-bearing rocks, nature and thickness of overburden, location of faults and fold axes, and similar features. Such studies also yield many measured sections of coal and associated strata, which show variations in the thickness of the beds, and the intervals between coal beds. Taken as a whole, detailed geologic studies provide much useful information for mine operators and engineers. As Dr. Cady points out, this type of geologic work is arduous and time consuming, but it provides the basic data that are necessary both in the development of our coal fields, and also in the preparation of coal-reserve estimates, which are discussed in the next paragraph. The U. S.

Jan 1, 1950