Search Documents

By Louis Raymond, John E. Dorn

The object of this investigation was to analyze the recovery that arises when the stress on a specimen undertaking creep is reduced. For this purpose annealed specimens of high-purity aluminum were precrept under a stress of 1000 bsi to a strain of 0.08 following which the stress was reduced for various periods of time to 10, 250, 500, or 700 psi. When the original stress was reapplied the subsequent creep curve lay above that for the unre-covered state and below that for the original annealed state. Analyses on the kinetics of this recovery as a function of the temperature gave a stress-sensitive activation energy that decreased as the reduced stress was increased from a value of 64,000 cal per mole at 10 psi to 37,000 cal per mole at 750 psi. Recovery was also detected and measured during creep under the reduced stress. Following a short initial period, the creep rate under the reduced stress increased monotonically until it reached the secondary-creep rate for the reduced stress. The temperature dependence of this phenomenon was also shown to be correlatable in terms of the previously deduced activation energy for recovery. The activation energies for creep of most pure metals at high temperatures have been shown to agree well with those for self-diffusion.'j2 Since the true secondary stage of creep is usually due to the steady-state balance between the rate of strain hardening and the rate of recovery, it is generally thought that the activation energy for recovery of the creep-induced substructure equals that for creep itself. A shoft time ago, however, Ludemann, Shepard, and Dorn~ found that the activation energy for recovery of the creep-induced substructure in high-purity aluminum under zero stress was almost twice that for self-diffusion, namely about 65,000 cal per mole; obviously recovery under reduced stresses differs in some significant way from the recovery that accompanies the secondary stage of creep. The major purpose of this investigation is to study the effect of stress on the re- covery of the creep-induced substructure in order to provide a better understanding of the recovery mechanism itself. EXPERIMENTAL TECHNIQUE High purity aluminum, containing 0.004 pct Cu, 0.002 pct Fe, and 0.001 pct Si, used in this investigation, was in the form of 0.100-in.-thick sheet which has been cold-rolled to the H-18 temper. Creep specimens were milled from the sheet with their tensile axes in the rolling direction. All specimens were then heated at 686°K for 1 hr followed by air cooling in order to produce an annealed structure which exhibited a uniform equiaxed grain size of about 4 grains per mm. Tests were run in creep machines fitted with Andrade-Chalmers type of lever arms so contoured as to maintain the stress constant to within 0.05 pct of the reported values. Constant temperatures to *O.l°K were obtained by complete immersion of each specimen in a temperature-controlled and agitated bath of molten KN02-KNOs mixture. Where changes in temperature were involved, the change was effected in less than 2 min by manually replacing one bath by another controlled at the second temperature. Displacements over the gage section were sensed by linear differential transformers, the output of which was autographically recorded. The calculated strain measurements were sensitive to 5x EXPERIMENTAL PROCEDURE The following analyses are based on extensions of the previously announced effect of the temperature on the creep strain,2 namely for a = constant, where e = the total true tensile creep strain for a given applied true tensile stress, t = the duration of the test, R = the gas constant, T = the absolute temperature, Q, = the activation energy per mole for creep which is independent of the stress, / = a function of 8, = and of the stress, and a = the stress. The validity of this correlation for high-purity aluminum is demonstrated in Fig. 1 for temperatures in the near vicinity of 600°K; the activation energy for creep, Q,, which is approximately that for self-diffusion, is insensitive to the applied stress

Jan 1, 1964

By K. E. Manchester, A. H. Clark

Hall measurements have been made on three groups of silicon samples, which were implanted with boron, aluininunz, and phosphorus ions. Boron and phosphorus implants show essentially bulk properties when annealed under previously determined conditions, i.e., 15 min at 80O°C for boron and 10 mirz at 600°C for phosphorus. Bulk properties were also observed in alu?rrilzum-implanted samples when ion concentrations were below 1015 cm-'; however, strange low- terrzperalure behavior and a falloff in cavrier concenlralion was observed for sarnples with ion concenlration abozle loL5 ern-'. This can be attributed to solid-solubility effects since the average bulk concentration f0.r the sample exhibiting bulk properties was below the reported solubility limit for aluminum, while the other samples were above the limit. A detailed study of the annealirzg process indicates that mobilities reach bulk c~alues in phosphorus implants at 250DC, in alutninurn ivnplanls a1 500°C, and in boron implants at 700°C. A simple rnodel has been proposed to fit the annealing data. THE technique of semiconductor doping by direct injection of energetic ions is being actively investigated at this Center. Previously published results from this laboratory have been concerned with the investigation of implanted profiles in silicon and the electrical properties of the resultant p-n structures.1'2 Diode properties have been reported for junctions produced by implantation of boron ions and aluminum ions in n-type silicon and phosphorus ions in p-type silicon. Reverse current characteristics, as well as electron diffraction data, have indicated that the damage to the structure produced by the energetic ions during the stopping process can be minimized by a gentle anneal. The time-temperature conditions for this process have been determined by sheet resistivity studies.3 Electrical profiles of implanted phosphorus ions which have been determined by a differential sheet conductivity technique are based on the assumption that the carrier mobilities and activation energies for ionization are the same as in bulk silicon. These assumptions have been substantiated experimentally by measurement of Hall constants and resistivities of these implanted structures and the results are presented herein. After establishing the bulk property equivalence of the annealed layers, a more detailed examination of the annealing process was undertaken. The sheet resistivity technique initially used to determine anneal conditions has been broadened to include Hall constants and mobility behavior with anneal conditions. PROCEDURE The three groups of samples prepared for Hall measurements were implanted with mass-separated beams of boron, aluminum, and phosphorus ions. Ion concentrations are equivalent surface concentration and they have been determined from beam current measurements during implantation. Implant conditions for the samples are shown in Table I. In all cases, the samples had previously been angle-lapped on one edge and the junction delineated with an HF-copper sulfate solution. The surfaces of the implanted regions of the samples were exposed to the delineating solution and in the case of the "n"-type phosphorus-implanted areas it was later discovered that a finite amount of surface could be etched by this solution. This is discussed in the section on results. The implanted samples were ultrasonically cut into the conventional six-probe configuration shown in Fig. l.* In the annealing studies, for which the meas- urements were taken at room temperature, the sample holder was a Bakelite jig incorporating tungsten mechanical probes. The other measurements were taken using a conventional liquid-nitrogen cryostat, in which the temperature could be varied from 77" to about 400°K. For these measurements, 10-mil aluminum dots were evaporated onto the samples and alloyed with the silicon at 530°C for 15 min. The samples were then mounted in flat-packs, and gold wires were bonded to the aluminum dots. The electrical measurements were made with either a Leeds & Northrup K-5 Potentiometer, a Keithley 147 Nanovolt Null Detector, or a Keithley 601 Electrometer. No external bias was applied to the substrate. There is an inherent self-biasing arrangement at one or the other of the current contacts (depending upon the polarity), and this suffices to limit the current flow to the implanted layer. The magnetic field was generated by an A. D. Little electromagnet. Except for occasional checks of linearity of the Hall voltage with

Jan 1, 1969

By H. E. Cline, E. F. Koch, J. L. Walter

It has been postulated and, in a few instances shown, that some kind of dislocation structure will be present at semicoherent interfaces to accommodate small lattice mismatches. In the present study of the NiAl-Cr eutectic, regular arrays of interface dislocations are observed at the boundary between the chromium-rich rods and the NiAl-rich matrix. The networks were examined by transmission electron microscopy and selected area diffraction. The rods and the matrix have a crystallographic relationship in which all directions and planes of the two phases are parallel. The dislocation networks are cmposed of a<100> dislocations lying on the intersections of the cylinders with (100) planes. Dislocations forming hexagonal rather than square arrays are also observed at certain areas of the network. The morphology of the network is consistent with the interpretation of mismatch being accommodated by interface dislocations in the cylindrical geometry. The measured spacing between dislocations was used to calculate an apparent lattice mismatch between the phases (˜0.35 PCt)interface network energy (-140 ergs per sq cm), and network strengthening (-10,000 psi). It has been proposed by Frank and Van der Merwe1 that dislocations should be present at the boundary between two semicoherent crystallographically related phases. The role of the interface dislocations would be to reduce the internal stresses, caused by the mismatch in atomic spacing across the interface. Such dislocations have been observed at the interface between expitaxially grown films and Substrates.2-4 Interfacial dislocations have also been observed at precipitate-matrix interfaces.&apos;-&apos; Directionally solidified eutectics have been shown to have semicoherent phases1&apos; and would, therefore, be expected to have interfacial dislocations as found by Weatherly at a lamellar fault in A1-A12Cu.11 The NiAl-Cr eutectic appeared to be a promising system to examine because both phases are cubic, the lattice mismatch is small, and the phases are crys-tallographically related. Furthermore, the eutectic is easily thinned for transmission microscopy. Indeed, interfacial dislocations were observed and this report describes the nature of the dislocation networks in the boundary between the NiAl-rich ma-trix-phase and the fine chromium-rich rods.21 I) EXPERIMENTAL PROCEDURE Ingots, 3/4 in. in diam and 6 in. long were made by melting in vacuum and casting under argon using 99.9 pct pure material. The composition, in at. pct, was 33 pct Ni, 33 pct Al, and 34 pct Cr. The ingots were then placed in A1203 crucibles on a water-cooled base, melted by means of induction, and withdrawn from the hot zone at the rate of 1 in per hr under argon.* * T his material was first directionally solidified in this laboratory by E. R. Stover Slices were taken perpendicular to the growth direction of the directionally solidified ingot for metallography and for transmission electron microscopy. The electron transmission samples were thinned mechanically, then thinned electrolytically in A-2 electrolyte* *A-2 electrolyte: 62 ml perchloric acid, 700 ml ethanol, 100 ml butylcellosolve, 137 ml distilled H20. until a hole appeared in the foil. 11) EXPERIMENTAL RESULTS A) Optical Microscopy. The microstructure, viewed on a plane perpendicular to the growth direction, is shown in Fig. 1. The structure consists of cells or colonies of parallel chromium-rich rods in the NiAl matrix. The cells occur when there are impurities present12 or, in a ternary eutectic, if the composition is slightly off the eutectic composition. The axis of the chromium-rich rods is parallel to the growth direction except near the cell boundaries. Here the rods may assume angles to the growth direction; however, examination shows that the crystallographic relationship between the rod and the matrix remains the same. Fig. 1 includes cell boundaries where the rods formed at a large angle to the growth direction. The variation of rod position across the cells made it possible to Fig. 1-Structure on plane perpendicular to growth direction. Rods near cell walls are at large angle to growth direction. Magnification 315 times.

Jan 1, 1970

By A. Stanley, J. C. Mead

The MacIntyre Development of the National Lead Co. is located at Tahawus, N. Y. The operations involve the mining and concentrating of a titaniferous iron ore to produce an ilmenite concentrate and a magnetite concentrate. Construction of the MacIntyre plant was commenced during the summer of 1941,when world conditions threatened to cut off the supply of Indian ilmenite. An open pit mining operation was developed and the crushing and milling equipment put in operation in July 1942. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. The metallurgy of the mill operation was described by Mr. Frank R. Milliken,* Plant Manager, National Lead Company, MacIntyre Development, and presented at the AIME New York Meeting, February 1948. The magnetite concentrate produced in the milling operation was too fine (minus 20 mesh) to be used directly in iron blast furnace operation, and most of the magnetite had to be stockpiled in 1942 and 1943. In 1943, the Defense Plant Corp. built a Greenawalt sintering plant at Tahawus, N. Y., to put the magnetite concentrate in a more suitable form for use in the iron blast furnace. The Greenawalt sintering plant consists of three 10 by 25 ft sintering pans designed to produce 1800 gross tons of sinter per 24 hr. The vacuum to each pan is produced by two Greenawalt fans in series, pulling approximately 30,000 cu ft of air per minute at 50 in. water gauge vacuum. The plant started operation in August 1944. The present plant production averages 25 tons per operating pan hour (approximately 224 lb per operating hour per square foot of grate area) of plus 1 in. sinter. Raw feed to the plant consists of 61 pct magnetite, 4 pct anthracite coal culm, and 35 pct minus 1 in. return fines which are conveyed to a pug mill where the materials are mixed thoroughly and water added to give the mixture 5.5 to 6 pct moisture. The mixed prepared feed is conveyed to two 4 by 10 ft vibrating screens where the minus 1 in. plus 5/8 in. return fines are screened out and discharged into a surge bin for use as a hearth layer. The minus % in. prepared feed is discharged into another surge bin for use as prepared feed. A charge car, electrically operated, having a capacity of one charge of prepared feed and several charges of hearth layer, lays a thin layer of plus 5/8 in. return fines and 9 1/2 in. depth of prepared feed into the pans. A fluffing roll and a vibrator on the car fluffs and spreads the prepared feed into the pans. An ignition car, electrically operated, ignites the top of the bed with a 30 sec flash burn. The 9 1/2 in. bed sinters in approximately 13 min. Dumping the pan, and recharging and igniting the bed requires 2 min. To improve the quality of the ilmenite concentrate produced in the mill and to reduce the amount of titanium dioxide lost in the mill tailings and in the magnetite product, extensive research work and pilot plant operations have been done on grinding the crude ore to minus 65 mesh size (rather than to minus 20 mesh) and concentrating it by a combination of magnetic separation (for magnetite recovery) and flotation (for ilmenite recovery). These tests have proved successful in increasing ilmenite recovery and grade. With the development of the ilmenite flotation process to a stage where a full scale flotation plant was in the design stage, the problem arose of handling the 65 mesh magnetite concentrate that would be produced. In order to study and solve the problems of handling and sintering the 65 mesh magnetite in the sinter plant, a pilot sinter plant was plus from John E. Greenawalt. The effect of using 65 mesh magnetite in the sintering operations was then studied on the 2.4 sq ft test pan, operating under conditions as similar to the large plant as could be set up in the laboratory. A series of tests were run in the test pan on present sinter plant feed that had been mixed in the plant pug mill. An average production and an average quality of sinter produced in this series

Jan 1, 1950

By Paul A. Farrar, Sanford Adler

The Tz-Zr system was reinvestigated using both metallographic and X-ray diffraction techniques. It mas found that titanium and zirconium are soluble in all proportions in both the a and 0 phases. The minimum in the transformation was found at 50 at. pct and 535°C. THE Ti-Zr system has previously been the subject of several investigations.1-6 A study by Hayes et al.5 using magnesium-reduced titanium and zirconium melted in graphite crucibles indicated that the system was a continuous series of solid solutions in both a and 0 phases with a minimum at approximately 545°C and 65 pct* Zr. These conclusions were substantiated by the work of Duwez4 as well as by the limited data of Craighead et al.,3 Fast,2 and deBoer.1 However, a more recent investigation of the titanium-rich region by Ence and Margolin6 indicated that the solubility of zirconium in a, titanium at 500°C is approximately 22 pct with the a + 0 field extending to approximately 47 pct Zr. Therefore in order to resolve this discrepancy the following investigation was initiated. EXPERIMENTAL PROCEDURES The alloys used in this investigation were prepared as 20- to 30-g buttons by nonconsumable electrode melting in a helium atmosphere. The starting materials were Bureau of Mines titanium BHN 71 and Foot Mineral iodide crystal bar zirconium. The titanium was premelted before the alloys were prepared to avoid excessive weight losses in the final melting. The compositions of the alloys prepared were as follows: Ti-12.0, 22.2, 29.0, 39.6, 50.0, 58.0, 72.4, 83.5. and 90.8 pct Zr. Prior to heat treatment the alloys were cold-worked 10 to 20 pct, stopping at the first signs of cracking. Specimens for heat treatment were wrapped in molybdenum sheet and annealed in argon-filled quartz capsules for the following times and temperatures: 750°C-40 days, 675°C-61 days, 600°C—109 days, 575°C-112 days, 550°C-112 days, 525°C—127 days, and 450°C —153 days. Quenching was accomplished by breaking the capsules in an iced-brine solution. The standard techniques used for polishing the specimens involved belt grinding, grinding on emery paper, polishing electrolytically, and etching with Remington "A" etch7 or "R" etch 8 Debye-Scherrer X-ray powder photograms were obtained for a number of samples using a 114.6-mm camera and CuK, radiation. Exposure times were from 19 to 23 hr. The powder samples were obtained by filing to 270 mesh size. After filing the samples were wrapped in molybdenum foil capsuled in quartz and reannealed at the temperature of original heat treatments; following the heat treatment the samples were quenched into iced brine without breaking the capsules. RESULTS AND CONCLUSIONS On the basis of the microstructural examinations of the heat-treated samples and of the X-ray diffraction data, the Ti-Zr system shown in Fig. 1 was constructed. The data indicate that a, and 0 titanium form a complete series of solid solutions with a, and ß zirconium. The minimum was found to occur at 65 pct (50 at. pct) Zr and 535°C, in excellent agreement with the earlier investigations,1-5 see Fig. 2. Typical microstructures are shown in Figs. 3 to 7. Figs. 3, 4, and 5 show the 22.2, 39.6, and 50.0 pct Zr alloys after heat treatment at 675°C for 61 days with the 22.2 pct Zr showing equiaxed a, and the 39.6 pct Zr alloy a + transformed ß, while the 50 pct Zr alloy shows only transformed B. Figs. 6 and 7 show the 29.0 and 39.6 pct Zr alloys after heat treatment for 109 days at 600°C. The 29 pct Zr alloy has an equiaxed a structure while the 39.6 pct alloy has a partially recrystallized a+ß structure. X-ray diffraction data obtained from the 50 pct Zr alloys after heat treatment at 525° and 450°C as well as from the as-cold-rolled material showed only those lineos which couid be indexed a: a titanium, good agreement with the previously published values. 2,4,5,9 Chemical analysis* of the 50 pct Zr alloy

Jan 1, 1967

By J. E. Burke, A. M. Turkalo

IN 1923 Desch¹ pointed out that the grains in a metal which is anisotropic with respect to its thermal coefficient of expansion would contract differently upon cooling, and that the stresses developed might approximate the plastic strength of the metal. More recently Boas and Honeycombe2-5 studied the behavior of several metals upon thermal cycling and observed that the stresses developed in arlisotropic metals are great enough to produce slip lines in individual grains and a roughening of the specimen surface. This phenomenon they have named "thermal fatigue." The mechanism they propose involves essentially a kneading of the grains, the deformation being alternately in compression and tension in a given grain as the temperature is changed in one direction and then the other. The present work was undertaken to investigate the possibility that an additional mechanism might operate to produce plastic deformation during thermal cycling—a "thermal ratchet" that depends upon a combination of grain boundary flow to relax the stress that develops between differently oriented grains upon raising the temperature and transcrys-talline slip to relax the oppositely directed stress which develops on lowering the temperature. Thus, thermal cycling should produce a nonreversible distortion such that certain grains will change shape differently from their neighbors with a simultaneous displacement being produced at the grain boundary. Temperature Dependence of Grain Boundary and Grain Strength The critical resolved stress for the initiation of slip in metal grains is only mildly affected by temperature." For example, in cadmium it decreases from 0.15 to about 0.05 kg per sq mm when the temperature is increased from 20° to 458°K and further temperature increase causes little further decrease. On the other hand, the work of KG1 indicates that the grain boundaries behave in a viscous fashion that can be described8 by the expression: t = BVexp(Q/RT) [1] t is the shearing stress on the boundary; B, a constant; V, the flow rate at the boundary; Q, the activation energy for grain boundary flow; R, the gas law&apos;s constant; and T, the absolute temperature. Eq 1 indicates that the stress necessary to cause a given grain boundary flow rate, V, decreases rapidly with increasing temperature. The value of the constant B is such that at sufficiently low temperature and ordinary strain rates deformation will occur preferentially by slip rather than by grain boundary flow. There is considerable evidence to indicate Consider the bicrystal shown in Fig. 1. In grain 1 the slip plane lies 45 " to the boundary while in grain 2 the slip plane is 90" to the boundary. The coefficients of expansion of the grains in a direction parallel to the length of the crystal are a1 and a, with a, > a2 for the orientations shown. The sequence of events that can occur upon heating and cooling this specimen is illustrated schematically in Fig. 2. Initially there is assumed to be no stress in the specimen (A). Upon heating, grain 1 attempts to become longer than grain 2, but is constrained by grain 2. Thus grain 1 is loaded in compression and grain 2 is loaded in tension, and a shearing stress is present across the boundary (B). As the temperature is increased, the stress will build up, and finally grain 1 will be plastically deformed by slip, since the greater stress is resolved on its slip planes. Any further heating will result in more slip and the stress will remain constant until some temperature T* is reached where the stress can be relaxed by grain boundary flow.† At this relaxation temperature (C) a step will appear between grain 1 and grain 2. Further heating above T* will cause grain 1 to become relatively longer, but no stress will appear because the grain boundary is too weak to support the stress (D). Upon cooling again, at T* (E), the grain boundary will again be able to support a shearing stress, and upon cooling further, grain 1 will be loaded in tension and grain 2 in compression (F). When the decrease in temperature below T* is sufficient to impose the critical shear stress upon the slip plane of grain 1, it will be stretched by slip.

Jan 1, 1953

By Harlan W. Nelson, James B. Purdy

A study of data obtained during laboratory tests to determine the suitability of bituminous coals for use in residential underfeed stokers of the clinkering type has led to the following general conclusions: 1. Performance data obtained during the test furnish useful and practical information upon which to judge the performance of stoker coals. 2. Conclusions derived from the results of evaluation tests are in general agreement with use experience of the coals in the field. The method is of practical use in this regard. 3. Few direct relationships were found between data furnished by the evaluation test and determinations by standard laboratory tests. This is particularly true with regard to coke formation and clinker formation, two of the most important factors in determining the degree of satisfaction to be obtained in applications of the small underfeed stoker. It has not been the intention in this paper to prescribe this evaluation test as the best method for the evaluation of coals for use in residential stokers. That there are other test methods having similar objectives serves to point out the necessity for full-scale laboratory tests. At the present time, a standard test procedure for the evaluation of coals for use in residential stokers is not available. For the past several years a joint committee, appointed from the membership of the Residential Stoker Committee of Bitulninous Coal Research, Inc., and from the Engineer- ing and Research Committee of The Stoker Manufacturers Association, has been working to develop a standard procedure for testing and evaluating bituminous stoker coals. This procedure has been completed to the extent that it has been drawn up in tentative form. It is now planned to install the equipment in several laboratories and to run check tests, using portions of identical lots of coal, to determine the degree of reproducibility offered by the method. Completion of this standard test procedure should greatly facilitate the evaluation of coals for use in residential stokers. Acknowledgments The cooperation of coal operators sponsoring the coal evaluation tests, in granting permission to use data and results from their tests, is gratefully acknowledged. Acknowledgment is also made to Carroll F. Hardy, Chief Engineer, Appalachian Coals, Inc., for his interest and timely suggestions on the preparation of this paper. Special thanks are due to Ralph Sherman, Assistant Director, Battelle Memorial Institute, who was largely responsible for development of the evaluation procedure, for helpful suggestions and advice. References I. H. A. Sherman: The Evaluation of Coal for Use in Domestic Stokers. Univ. of Ill., Eng. Experiment Station, Circular No. 39 (1939). 2. . Q. Shotts: The Relation of Free- swelling Indexes to Other Characteristics of Some Alabama Domestic Stoker Coals. TP 2314, Coal Tech., (Feb. 1948); Trans. AIME (1948) 177, 502. 3. . J. Helfinstine and C. C. Boley: Correlation of Domestic Stoker Combustion with Laboratory Tests and Types of Fuels 11. Combustion Tests and Preparation Studies of Representative Illinois Coals. Ill. State Geol. Survey, Re1. of Zntlestigations No. 120 (19467 ) p. 35. DISCUSSION E. R. Kaiser*—AS a former fuel engineer assigned to residential stokers at Battelle, the writer has read with considerable interest the paper by Messrs. I&apos;urdy and Nelson. It is gratifying to note that earlier test techniques have been developed and that criteria found important in the years 1935 to 1938 are still important in judging the performance of stoker coals for residential heating. The authors have plotted a number of the primary coal data singly against performance data of the stoker in an effort to establish relationships. Unfortunately, wide scattering of points usually resulted, which did not illustrate what experience generally indicates to be the case. For example, Fig 3 indicates almost no trend in the percentage of released ash converted to clinker with change in ash-softening temperature. Other factors, such as fuel bed temperatures and zones of heat release must have influenced the results. In the present state of our knowledge, we cannot explain all of the reasons why suitable stoker coals perform satisfactorily, nor why one satisfactory coal may be better than another. It would therefore

Jan 1, 1950

By R. D. Russell, R. M. Farquhar

SOTOPIC tracers have become an important aid in following the progress of chemical processes in the laboratory. It has recently been found possible to utilize a system of naturally existing iso-topic tracers to obtain information about the geological history of lead ores. Common lead, such as is found in lead deposits, is a mixture of four stable isotopes having atomic weights 204, 206, 207, and 208. Of these, the last three are identical with the lead isotopes produced as stable end products of the radioactive decays of uranium and thorium: the first, lead-204, is not known to be produced on the surface of the earth by any process. Since uranium and thorium Occur in the surface regions of the earth in amounts comparable with lead, and since the half-lives of uranium and thorium isotopes are of the same order as the age of the earth, they produce the radiogenic lead isotopes in amounts comparable to the amount of nonradiogenic lead present. Every significant exposure of a sample of lead to uranium and thorium will therefore lead to the permanent alteration of the lead isotope ratios in that sample. It is this unique property of lead that serves as a means of tracing the history of a lead sample in terms of its contacts with the radioactive elements. If lead from a lead mineral has been analyzed with a mass spectrometer, the measured isotope ratios are determined entirely by the isotope ratios of primeval lead, which are identical for all minerals, and by the particular history of the sample. It follows that for samples from any particular geological area, observed differences in the isotopic composition are enough to distinguish different geological histories. An illustration of the qualitative application of this statement is given in Table I by analyses of some galenas from the western Cordillera. Samples from deposits in Pre-Cambrian sediments have very different lead isotope ratios from those of the ores in the Paleozoic sediments. Although the two types are associated closely geographically, it is apparent that they have had quite different histories and have probably been emplaced at quite different times, as the ideas outlined in the following section suggest. Even when applied quantitatively, a lead isotope analysis can never indicate a unique history of any lead sample. However, it greatly restricts the choices available and combined with other geological and geochemical data can lead to a much better understanding of the genesis of lead ores. General Character of Lead Isotope Variations: Early isotopic analyses of common leads by Nierl showed that geologically younger leads were generally richer in isotopes of masses 206, 207, and 208, with respect to that of mass 204. This regularity of measured lead isotope ratios can be easily observed by plotting each of the ratios Pb207/Pbm and Pb205/ Pb204 against the ratio Pb206/Pb204. In both graphs the points lie scattered closely about a well defined mean curve. It was immediately supposed that this regularity resulted from the growth of all leads from a common primeval lead present at some time, To, early in the earth&apos;s history. Lead in the outer part of the earth would become continually enriched in the radiogenic isotopes as a result of the uranium and thorium intimately associated with it. The subsequent extraction of some of this lead and formation of a lead mineral free of the radioactive parents provide samples of lead existing in the earth at the time of mineralization, T. Younger leads in general will be richer in the radiogenic isotopes because they have been associated with uranium and thorium for a longer time. Then lead ratios would be given by the formulae: (Pb206/Pb204)YTPb^/Pb204) +f "(u201) kdt T (Pb207Pb204)r = (Pb208/Pb204)T0 + J (U295/Pb204) k&apos; dt T (Pb208/Pb204) t = (Pb208Pb204 + J (Th204) A." dt [1] where A, A&apos;, and A" are the decay constants of U238, U285 and Th232. Summaries of measurements of radioactivity of surface rocks, such as given by Faul,2 are of limited

Jan 1, 1958

By G. Britsianes, T. L. Joseph

THE reduction of a lump of iron ore is a complicated sequence of up to three reactions proceeding simultaneously in a gas-solid system. As the ore moves down the blast furnace into zones of higher temperature and higher reducing power, it is successively reduced through the three oxides of iron into metallic iron. The reduction process involves much more than chemical problems. Physical factors add to the complexity of the overall process. Under optimum conditions, reduction of the ore is completed at a level about one-half way down the blast furnace stock column. At this point, the ore undergoing reduction has attained a temperature of about 1000°C and has been in the furnace for about 6 hr. On the practical side, the behavior of the ore during smelting has been of great interest to operators. Unsatisfactory blast furnace operation on burdens containing magnetite ore or badly slagged sinter has often been attributed to poor re-ducibility. The question of reducibility has also been raised in formulating quality standards for agglomerates such as nodules, briquettes, and pellets. In the present investigation, the solid phases formed during reduction were studied as a step toward a better understanding of the overall process. Equilibrium Studies The iron-oxygen equilibrium diagram shown in Fig. 1 reveal; a number of facts pertinent to the gaseous reduction of iron ores. This diagram is from the work of Darken and Gurryl, 2 and represents a correlation of the best available data. Four solid phases may exist during the complete reduction of hematite to metallic iron. These are hematite (Fe2O3), magnetite (Fe3O4), wustite (FeO), and iron (Fe). The wustite phase is a solid solution which is not stable below 570°C. At this temperature the solid solution undergoes a eutectoid-type of decomposition into the phases, magnetite and iron. Thus above 570°C, the diagram dictates that a hematitic ore should pass through a four-phase sequence on reduction to metallic iron. Below 570°C, only hematite, magnetite, and iron should appear. Information on the iron-oxygen system has been derived largely from CO and H2 reduction equilibria. The Fe-C-0 relationships have been studied extensively by R. Schenck and his coworkers and well summarized by H. Schenck.3 More recent studies have been made by Darken and Gurry.1, 2 Data from these sources have been combined and plotted in Fig. 2. With respect to the Fe-H-O system, the works of Emmett and Schultz4 seem the most reliable, and these data have also been included in Fig. 2. Certain physical properties of the solid phases of the iron-oxygen system are summarized in Table I. The crystallographic information is of special interest as much of the present work has been concerned with the X-ray analysis of the products of reduction. Reduction with Hydrogen The reduction of ore with hydrogen is the net result of two or more gas-solid reactions. Above 570°C, the reaction sequence may be represented by stoichiometric stages as follows: 3Fe203+ H2e2Fe,O, + H20 [1] 2Fe3O, + 2H2 6FeOw + 2H2O [2] 6FeOw + 6H3 ^ 6Fe + 6H=O [3] Fe2O3 + 3H2 ^ 2Fe + 3H,O. [4] These reduction reactions follow the general form: A (solid) + B (gas) e C (solid) + D (gas). This type of gas-solid reaction has been investigated by Langmuirl&apos; who has shown that such reactions can occur only at the boundary between the two solid phases. Furthermore, a nucleus of the second phase must initiate the reaction. Once such an interface exists, the reaction proceeds through a layer of the solid reaction product (C). The specific mechanisms involved will depend a great deal on the properties and condition of this particular layer. A number of heterogeneous reactions such as the dehydration of single crystals of copper penta-hydrate and the calcination of limestone follow this type of process. It should be noted that the inter-facial type of reaction also occurs even in dense polycrystalline material which simulates a mono-crystalline behavior.

Jan 1, 1954

By G. B. Thomas

Several methods of analyzing pressure build-up data in wells have been presented by various authors. This paper reviews the theory and method of D. R. Horner and presents example calculations performed on data obtained by testing several different types of wells. These calculations include, (1) graphical estimation of final static pressure, (2) determination of the productive capacity of the pay away from the well bore and. (3) the degree to which the formation adjacent to the well bore has been damaged by completion or other causes. The methods of testing and precautions which should be taken to assure the best data possible are discussed. Limitations and reliability of calculated results are also treated. INTRODUCTION Pressure testing of wells is generally limited to the determination of producing and static mean formation pressures. The so-called "static" pressure determination.. along with PVT, electric log and production data, enable the reservoir engineer to determine, within reasonable limits, the drive mechanism of the reservoir and in some cases. the amount of edge water encroachment. Producing pressure tests enable calculation of productivity indices and allow the engineer to plan the systematic production of a pool for optimum conservation of suhsurface energy. The radial flow formula advanced by Muskat&apos; has been based on the assumption of incompressible radial fluid flow. It has been known that reservoir fluids do not behave in an ideally incompressible manner. For example, incompressible flow theory indicates a simple logarithmic relationship between the difference of the instantaneous and static well pressures when plotted against time. &apos;The latter stages of this type of plot of pressure build-up data generally show a marked devia-, tion from the earlier straight line trend. which deviation may be shown to be due to the compressible flow of fluids toward the well bore. Shut-in times of 24, 48. 72. or at most 96 hours are currently in wide use for determining so-called "static" reservoir pressure. Due to the continuation of compressible flow of fluids into the well bore long after this arbitrarily taken shut-in time, the determination of static pressures has almost invariably resulted in lower than equilibrium values. Materials balance calculations made early in the life of a reservoir often result in a calculated reserve which later observations prove to be too low. Failure to obtain reliable "static" reservoir pressures within the prescribed 24 or 48-hour build-up period has undoubtedly been a major factor in obtaining these low estimates. Comparison of theoretical and actual productivity performance has indicated that formation damage and not being able to attain true static pressures have been partially responsible for the observed discrepancies. Research into the theory of compressible flow behavior has resulted in methods of applying these theories to the testing of wells. Application of the developed theories to pressure build-up performance indicates that in many cases the following can be estimated. 1. The static reservoir pressure. 2. The in-place effective formation permeability away from the well bore. 3. The degree or extent by which the formation has been damaged adjacent to the well bore, either through completion methods or subsequent damage due to fluid entry. REVIEW OF THEORY Horner2 has shown that the pressure build-up within a "point source" well is approximated by the following formula: Equation (1) is the approximate "point source" solution to the radial compressible flow equation advanced by Muskat. The solution assumes the following: 1. A point source well is producing at constant rate from the center of an infinite reservoir with a constant pressure at its external boundary. 2. The fluid flowing is present in one phase only. 3. The compressibility and absolute viscosity of the fluid remain essentially constant over the range of temperature and pressure variation encountered. 4. The well i.; shut-in at the sand face arid there is 110 after production into the well bore. 5. The formation permeability is homogeneous in the direction of flow. From Equation (1) it can be seen that if an ideal well were shut-in while producing from a reservoir under the conditions assumed, the pressure build-up would be a logarithmic func-

Jan 1, 1953

By Alan Stanley

THE Maclntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.1 Pigment plant production demands that the MacIntyre mill produce a 44.7 pct. TiO2 ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the Maclntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from one level to the next.. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the, physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO2 has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO2 has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the Maclntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO2 was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiO2 a constant gravity would invariably be obtained, and as the TiO2 value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct TiO2 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO2 value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO2 and as the specific gravity increased the trend was for the TiO2 assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. [ ] Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1952

By D. M. Schuster, E. Scala

The elastic effects occurring in the matrix of a composite reinforced by discontinuous fibers were studied by means of photoelastic techniques. A hirefringent plastic was employed as the matrix material with high-strength a Al2O3 whiskers as the reinforcing fibers. It was found that for whiskers aligned parallel to the tensile load direction: (I) Matrix reinforcement occurred along the length of the whisker to within about 5 diameters of the whisker tip for a length to diameter ratio, L/D, of 40. (2) Significant stress concentrations were created in regions immediately surrounding the tips; the fine as-formed tapered ends exhibited the minimum stress concentration whereas the square-ended whisker produced relatively high values, K r 2.5 for L/D = 40. (3) The axial and radial stress distributions could he determined quantitatively; the stress distribution at the whisker-matrix interface was in general agreement with theoretical calculations. (4) The highest source of stress concentration occurred at points of fracture in whiskers which had ruptured after incorporation into the composite. Whiskers aligned perpendicular to the load direction neither reinforced nor caused appreciahle stress concentrations in the matrix. ThE properties of composites have generally been formulated empirically on the basis of macroscopic tests. There are still many questions concerning the mechanical and chemical interactions occurring at the interface between the reinforcing fiber and its matrix. Continuously reinforced plastics and dispersion-hardened metals represent the two extremes of composite reinforcement. Whether artificially produced or formed in situ, the whisker composite falls between these two extremes and is an example of discontinuous fiber reinforcement. The effect of fiber shape, size, surface condition, and end configuration on the stress distribution in the matrix is important since the presence of stress concentrations, especially in any high-strength, thin-wall structure, could become the cause of catastrophic failure. DOW,&apos; in his theoretical discussion of discontinuous fiber reinforcement, has pointed out that appreciable stress concentrations occur at the tips or ends of the reinforcing fibers. It is the purpose of this study to examine directly, by means of the photoelastic technique, the stresses which occur in the vicinity of a discontinuity or whisker tip and to measure qualitatively and quantitatively the effects of whisker geometry when embedded in a birefringent matrix material. The use of sapphire (a A1,O3) whiskers was decided upon as the reinforcing agent because of their high elastic modulus (E- 60 X 106 psi) and in some cases strengths in excess of one and a half million psi. Sapphire whiskers are of further practical interest since they retain large fractions of their strength up to temperatures approaching the melting point (3720oF).2 The whiskers were grown, by the vapor-phase reaction commonly employed,3 as part of this study to insure a physically uniform supply. Tensile and bend tests were performed to verify that the whiskers were of the expected ultra-high strength. The high-strength whiskers can be identified and selected from the combustion boats by surface perfection, shape, and size; otherwise, strength values can vary by a factor of ten or more. Macroscopic defects are quite common on the surface of large bladed whiskers and the principal experiments were conducted with hexagonal whiskers of about 0.002 in. diameter and lengths ranging from 0.1 to 0.4 in. Upon completion of these two phases of the experiment, several birefringent resins were evaluated. A plastic, developed by Zandman,4 which is supplied by the Budd Co., was found most suitable and was used as the matrix material for the whisker composite throughout the study. It has a sensitivity of 60.5 lb per in. order, calibrated in tension and cures without introducing residual stresses. Young&apos;s modulus for this matrix material is 430,000 psi in the fully cured condition. Since good wetting and bonding between the sapphire and the matrix material is essential to the interpretation of the results, a wettability test was performed. The contact angle was measured to be 168 deg where perfect wetting is defined as 180 deg; therefore, the Budd Plastic wets the sapphire

Jan 1, 1964

By Alan Stanley

THE MacIntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.&apos; Pigment plant production demands that the MacIntyre mill produce a 44.7 pct TiO, ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the MacIntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from • one level to the next. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO, has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO, has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the MacIntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO, was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiOz a constant gravity would invariably be obtained, and as the TiO, value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct Ti02 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO, value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO, and as the specific gravity increased the trend was for the TiO, assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1953

By Alan Stanley

THE MacIntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.&apos; Pigment plant production demands that the MacIntyre mill produce a 44.7 pct TiO, ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the MacIntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from • one level to the next. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO, has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO, has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the MacIntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO, was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiOz a constant gravity would invariably be obtained, and as the TiO, value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct Ti02 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO, value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO, and as the specific gravity increased the trend was for the TiO, assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1953

By G. A. Vissac, R. G. Minet, N. E. Sylvander

R. G. Minet—The authors&apos; description of the remarkable progress made in the last few years in applying the fluidized solids technique to the problem of lignite drying and carbonization clearly demonstrates that engineering techniques available today may make many processes practical and profitable which a few years ago were considered otherwise. As pointed out in the article, the future of the carbonization step hinges on the value and utilization of low temperature tar. On paper, at any rate, this tar looks like a valuable raw material for the chemical industry to use. Some 50 to 60 pct may be converted to pitch for electrodes, roofing, road tars, and other valuable products; the 25 to 30 pct tar acids could conceivably form a basis for a new low cost resin or plastic of the phenolformalde-hyde type. Yet these materials are so new and dissimilar from available sources that much work must be undertaken by the chemical industry before they will be accepted. Now that the work of Dr. Perry and his colleagues has made a large supply of low temperature tar a real possibility, I would expect the chemical industry to accelerate its work in this field. On the basis of certain data available in the literature it appears possible to produce a more aromatic tar, although in smaller yield, by operating at temperatures in the range of 1300" to 1500°F. Operating a fluidized bed process for lignite at these conditions should be technically possible, at least, and could produce a tar having more familiar characteristics. I wonder if Dr. Parry would care to comment on such a possibility. Incidentally, in our own work on carbonizing coking coals in fluidized beds, using Ohio, Pennsylvania, and West Virginia high volatile bituminous coals, we have obtained yields which agree with the correlation given for tar yields vs moisture and ash-free volatile Btu. Our data are slightly under the line, but certainly in the range of the correlation. We have also obtained evidence in support of the authors&apos; statement as to the effect of air on the process. In our pilot plant all the heat required for carbonizing is released by internal combustion of char in the fluidized bed in normal operation. We are also equipped to obtain all carbonization heat by external electric heaters on the shell of the carbonizer while introducing only an inert gas to the process. We note no difference in tar yield or characteristics between the two operations. In the case of the gas, however, it appears that some hydrogen is consumed by the air combustion. We would be interested in hearing in a little more detail about the hot dust and char handling problems at Sandow. Have the authors found char subject to spontaneous combustion? Have they ever tried a coking coal in their pilot plant? V. F. Parry (author&apos;s reply)—Production of a more aromatic tar by operation of the carbonizer at 1300" to 1500°F does not appear to be economical. 1) The capacity of a reactor operating at 1500°F would be 30 to 50 pct less than the capacity at 932 °F and the cost of processing would increase materially. 2) The cracking of tar vapors in a reactor requires appreciable time to complete the reactions and it is doubtful that considering the very short time of residence of tar vapors within the reactor (4 to 10 sec after evolution) the basic character of the tar would be changed significantly. This is indicated from the data reported in Table XIV. 3) General studies have shown that it is advisable to operate at the minimum temperature to produce the maximum tar and minimum gas. 4) Operating problems and the maintenance of vessels and reactors, and the hazards of handling hot char, increase with the temperature of carbonization. It is technically possible to operate at temperatures as high as 1500°F, but in my opinion it is not economical or desirable. We believe that the primary tar must be won in the simplest way and then processed alone to change its character for production of desired products. It is interesting to have confirmation of our observations on the reaction of air with the products of carbonization. The major reaction is with the char, fol-

Jan 1, 1957

By O. D. Sherby, J. E. Dorn

For elevated temperature-constant load creep tests of a solid solution alloys, the creep strain is a function of a temperature-compensated time parameter 0 = je H/RT dt. The activation energy H is equal to o constant of about 36,000 cal per mol. The substructures resulting from a given creep stress condition are functions of the creep strain independent of temperature. Each new creep stress gives a new unique set of grain substructures; this is one of the factors responsible for the failure of the mechanical equation of state for creep. IN this report an attempt is made to correlate the creep properties of dilute a: solid solutions in aluminum with the subgrain structures that are developed during creep. The possibilities of such correlations have already been suggested by Wood et al. and others1-" who demonstrated that the subgrain structures are functions of the creep stress, creep strain, rate of creep, and temperature. Investigations by Sherby and Dorn&apos; have shown that the creep strain, E, at constant load for dilute a solid solutions of aluminum is given by the functional relationship: e = f(8,u,) [1] where: 0 equals te-AH/RT = temperature-compensated time; t, time; AH, activation energy, - 35,800 cal per mol; R, gas constant; T, absolute temperature, above 400°K; and u,, initial creep stress. Consequently, it was anticipated that the subgrain structure that develops during a constant load creep test should also correlate with any two of the three significant variables C, 8, and Another possible correlation between the subgrain structure and the creep variables is obtained by differentiating Eq. 1 with respect to time, whence the creep rate, 2, becomes: = (2L) (2) =f (, u,) e-AHRT [2] or: e = F (c e H/RT, 0) [3] For the minimum creep rate, ;,, 8 is solely a function of U, as revealed by Eq. 1. Consequently, at the minimum creep rate Eq. 3 reduces to: = F (eAH/RT) [41 Correlations between U, and i, eAH/RT were found valid for solid solution alloys of aluminum where AH was a constant of about 35,800 cal per mol. The parameter ;, eH/RT is identical to the Zener-Hollo-mon parameter8," used by them in evaluating the tensile properties of copper and other metals. Eq. 4 suggests that the subgrain structure developed during secondary creep might be correlatable with either of the two variables 2, e H/RT or u,. Some of the solid solution aluminum alloys which were discussed in an earlier report&apos; were also used in the present investigation. Sheets of these alloys were homogenized, cold rolled from 0.100 to 0.070 in. in thickness and then recrystallized to about the same grain size. Their chemical composition and grain size are recorded in Table I. Creep specimens were selected with their tensile axes in the rolling direction. The details for creep testing have been described10 and will not be repeated here. All creep tests were performed under constant load conditions. Experimental Results and Discussion Metallographic Structure of Creep Specimens: In order to obtain a preliminary concept of creep on the metallographic structure of high purity aluminum, the various ruptured specimens previously used to obtain the creep data for pure aluminum were polished and etched electrolytically in a dilute solution of fluoroboric acid. Oblique illumination was used to reveal the substructures which, for convenience, are shown in correlation with the vs. ;, eH/RT curve in Fig. 1. It is necessary to emphasize that the data for the curve refer to the various secondary stages of creep whereas the micrographs refer to the fractured creep specimens. Nevertheless a regular and systematic correlation is observed between E, eAH/RT (or the creep stress) and the micro-structure at fracture. For In (e, eAH/RT) = 42.3, which refers to creep at a high creep rate and a low creep temperature, the fractured aluminum specimen, as shown by the micrograph in the upper right-hand corner of Fig. 1, exhibited extensive deforma-

Jan 1, 1954

By Robert B. Fulton, Gill Montgomery

Fluorspar is the commercial name for fluorite, a mineral that is calcium fluoride, CaF2. The name, derived from the Latin word fluere (to flow), refers to its low melting point and its early use in metallurgy as a flux. It is the principal industrial source of the element fluorine. Cryolite, sodium aluminum fluoride, Na3AlF6, is a rare mineral which has been found in commercial quantities only in Greenland. The natural material has been supplanted by synthetic cryolite for its principal industrial use in the manufacture of aluminum. History Fluorspar was used by the early Greeks and Romans for ornamental purposes as vases, drinking cups, and table tops. Various peoples, including the Chinese and the American Indians, carved ornaments and figurines from large crystals. Its usefulness as a flux was known to Agricola in sixteenth century Europe. Fluorspar mining began in England about 1775 and at various places in the United States between 1820 and 1840. Production grew substantially following the development of basic open-hearth steelmaking, wherein it is used as a flux. Use was stimulated by growth of the steel, aluminum, chemical, and ceramic industries, particularly during World Wars I and II. Fluorocarbons entered the picture in 1931. The use of anhydrous hydrogen fluoride (HF) as a catalyst in the manufacture of alkylate for high octane fuel began in 1942. Differential flotation for separating fluorspar from galena, sphalerite, and common gangue minerals in the 1930s, and the application of heavy-media concentrating methods to the treatment of low-grade ores in the 1940s were outstanding technological advances that facilitated increased production. Recently, pelletizing and briquetting of flotation concentrates for use in steel furnaces and the development of flotation schemes for beneficiating ores containing abundant dolomite and barite have been major improvements in the industry. Uses of Fluorspar Fluorspar is used to make hydrogen fluoride, also called hydrofluoric acid, an intermediate for fluorocarbons, aluminum fluoride, and synthetic cryolite. It is used as a flux in the steel and ceramic industries, in iron foundry and ferroalloy practice, and has many minor specialized uses. Hydrogen fluoride (HF) is produced by reacting acid grade (97% CaF2) fluorspar with sulfuric acid in a heated kiln or retort to produce HF gas and calcium sulfate. After purification by scrubbing, condensing, and distillation, the HF is marketed as anhydrous HF, a colorless fuming liquid, or it may be absorbed in water to form the aqueous acid, usually 70% HF. Synthetic cryolite, organic and inorganic fluoride chemicals, and elemental fluorine are made from hydrofluoric acid. The acid itself is important in catalysis in the manufacture of alkylate, which is an ingredient in high-octane fuel for aircraft and automobiles, in steel pickling, enamel stripping, glass etching and polishing, and in various electroplating operations. The manufacture of one ton of virgin aluminum requires about 50 to 60 lb of fluorine content in synthetic cryolite and alumnium fluoride. This quantity, through improved technology and recovery practices, is being lowered significantly.

Jan 1, 1983

By L. Ekstrom, J. P. Dismukes

The homogeneity and microstrcture of zone-leveled Ge-Si alloys haw been investigated by sellera1 physical techniques and by metallography as a function of growth rate in the range 3 x 10 1x10 cm-sec&apos;, and as a system of alloy composition throughout the system. The temperature gradient at the solid-liquid interface was about 50 deg-cm-&apos; Cellular or dendritic structures char-acteristic of constitutional supercooling were ob-served except at very slow growth rates, which ranged from about 2 x 10 cm -sec for Ge 1 sio alloy to about 2 X 10&apos;5 cm-sec&apos;1 for Ge .sSio.s alloy. Using a simple model similiar to that employed for dilute solid the dependence upon compo-sition over the entire system of the critical growth rate for the onset of constiutional supercooling was calculated, and was .found to he in good agreement with the experimental results. THE recent discovery of the low thermal conductivity of Ge-Si alloys&apos; at high temperatures has revealed that these alloys have high efficiencies for thermoelectric-power generation.&apos;, Therefore, a reliable method was needed for the preparation of homogeneous samples required for definitive measurements throughout this alloy system. Due to the low diffusion rates in the solid alloys, the segregated samples obtained by quenching a melt are not readily homogenized by annealing.475 However. isothermal solidification from a melt of constant composition can produce uniform material. Of the available semiconductor crystal-growth procedures, the zone-leveling technique6 applied to a complete solid-solution alloy system by Wang and Alexander&apos; and by others provides a simple method of doing this. In the present work, the homogeneity and microstructure of zone-leveled alloys have been correlated with growth conditions, and the conditions for preparing homogeneous Ge-Si alloys have been established. This has provided insight into the solidification process of alloy semiconductors. EXPERIMENTAL PROCEDURE Sample Preparation. The Ge-Si alloy phase diagram4 shown in Fig. l(a) consists of a complete series of solid solutions. The zone-leveling technique used to prepare most of the samples consists of moving a zone of liquidus composition (C1) through charge material of the corresponding solidus composition (C,), as is illustrated in Figs. l(b) and l(c). To prepare the charge materials, high-purity germanium and silicon were pulverized in a steel hammer mill, cleaned magnetically, and melted together to make uniform chill castings. The zone leveling was carried out in a resistance-heated furnace similar to that of Mitrenin et al.&apos; shown in Fig. 2. However, a few specimens of high silicon content were prepared by the Czochralski technique. The growth rate ranged from 3.5 x X6 to 1.2 X 10~3 cm-sec-&apos;. Temperature gradients in the solid and in the melt were determined by recording the temperature as the molten zone passed over a Pt-Pt 13 pct Rh thermocouple contained in a small

Jan 1, 1965

By A. W. Gauger

IT is with some trepidation that I approach my subject, for I know that I shall at once incur the suspicion of the mechanical engineer, with his concern for boiler tests and efficiencies; of the mining engineer, with his mechanization problems; and of the chemical engineer with his unit processes. Nevertheless, it must be recognized that the technology of fuels, the systematic body of knowledge relating to the production, processing and utilization of mineral fuels, has grown to such proportions and involves so many widely diverse applications of fundamental science and engineering that it behooves us to stop and consider just what its status is in relation to other technologies, as well as in relation to the present and future needs of the social order. The time has come when technologists, applied scientists and engineers must consider the possible effects that their achievements may have 0n Society. The development of a machine to replace several hundred men is a fine achievement when considered solely from the point of view of creative endeavor. But what of the men who are displaced by the machine! Does not the responsibility for the development of this machine embrace as well the consequences of obsolescence and technological unemployment resulting from such development? I believe that it does and that we must recognize this fact in our practice of engineering and technology as well as in the training of future engineers and technologists. MAGNITUDE OF THE FUELS INDUSTRY Fuel technology is the body of knowledge that relates to the mineral fuels. The fuels industry is by far the most important of all our mineral industries. The chart in Fig. I, reprinted from U. S. Bureau of Mines Information Circular No. 6643, indicates the comparative values of metals, fuels and other nonmetallic minerals for the year 1929. Of the grand total of 13 1/4 billions of dollars in value of minerals at the mines, the mineral fuels contributed 48 per cent. Coal, with 34.4 per cent, exceeded the value of any other single mineral. In fact, the value of the production of the Pennsylvania anthracite mines alone annually exceeds the value of the gold production of the entire world. Petroleum and natural gas in 1020 contributed 14.3 per cent and 3.3 per cent, respectively, of the total value of world mineral production. So much for the world picture; let us now look at the situation in the United States. Over the 60-year period 1880 to 1939, $46,409,727,000 of metallic products, S80,788,852,000 of fuels (coal, petroleum, natural gas, natural gasoline) and $27,871,000,000 of nonmetallic minerals other than fuels were produced. The mineral fuels have contributed 52.7 per cent of the entire mineral wealth produced over this period that has seen such tremendous industrial development in our country. As a matter of fact, our present industrial civilization has been made possible through the use of the

Jan 1, 1942

By M. H. Cullender

The performance characteristics 01 gas wells producing from formations which fail to stabilize within a relatively short period of time are obscured by the interrelation of the coefficient (C) and the slope "n" of the conventional back-pressure curve q = C(P2 f- p2s)n An empirical method is presented whereby the characteristic or true slope (11) of the back-pressure curve may be determined for a particular gas well. For those gas wells which do not stabilize within a relatively short period of time, the coefficient (C) is considered as a variable with respect to time and as a constant only with respect to a specific time. Thus, the back-presrure performance of such a well is presented as a series of parallel curve5, each curve representing the performance of the well at the end of a given time interval. Through use of the method presented, a simple presture gradient is developed and maintained within the drainage area around a producing gas well during the test period in order that the variation of the coefficient (C) with respect to time does not obscure the true value of the lope. INTRODUCTION The back-pressure method of testing gas wells as set forth by Schellhardt and Rawlins1 is dependent upon the requirement that a series of flow rates and corresponding pressure data be obtained under stabilized conditions. These data arc then plotted on logarithmic coordinates of flow rate (Q) vs difference in squared pressures (P2f — P2s) in order to determine the constants (C) and (n) for Equation 1. With respect to this method of presenting the performance characteristics of a gas well, it should be pointed out that although Equation 1 is an empirical relationship, the form of the equation was justified to a considerable extent by an independent development by Muskat and Botset.2 This development was theoretical in nature; however, certain assumptions with respect to the type of flow existing (viscous vs non-viscous) were madc which may or may not be correct. As the use of the method presented by Schellhardt and Rawlins spread through the industry, it became evident that the method of testing was applicable for those wells which approached stabilized prbducing conditions within a relatively short period of time. Performance characteristics could not be determined by this method, however, for wells which approached stabilized protlucing conditions slowly over a considerable period of time. This characteristic of "slow stabilization" has generally been associated with gas wells producing frorn reservoirs of low permeability. As the demand for natural gas continued to grow through the years, a great number of wells were completed in reservoirs of low permeability which exhibited "slow stabiliz:~tion" characteristics. Consequently, the problem of determining the true performancc characteristics of these wells became more apparent. It is with this problem in mind that the isochronal performance method of determining the flow characteristics of gas wells is presented.

Jan 1, 1956