Search Documents

By J. H. Fletcher, S. M. Cassidy

Air has been cooled, heated, washed, humidified and dehumidified for many purposes and in many industries. At a number of metal mines air is conditioned to reduce the high humidity and unbearable heat found in deep workings, and at some mines air is washed to allay siliceous dust. Steam is introduced into the intake air at many coal mines, particularly in winter, for the purpose of keeping loose coal dust so moistened that the hazard of an explosion is lessened. This paper will describe a further successful application of air conditioning in a coal mine, where, for over three years, all intake air has been cooled to a constant temperature for the sole purpose of preventing roof falls. Effect of Warm Weather on Mine Roof It is generally known by mining men that some, if not all, coal mines have more trouble from bad roof during the warm summer months than in winter. Also, it has been observed that roof on intake airways is usually worse than on the return entries, after the air has circulated through the mine. Some mines and some coal seams are much more affected than others. In the Clinton district of Indiana, the No. IV coal seam has a good, firm, gray shale roof except during the summer months, when it deteriorates badly and falls in small slabs 1 to 6 in. thick. Timbering is not very efficacious during this period because in time the roof will shear around the supporting prop or crossbar and either dislodge the timber or leave it supporting only a few inches of crumbly shale (Fig. 1). This action is renewed each summer, choking airways with fallen slate, tearing down trolley wires, hampering haulage, endangering men and adding considerably to the deadwork cost. Only when mines have been worked for a period of years and have been advanced a long distance from the shaft do the active workings become comparatively free of this trouble, and even then the intake entries are still a source of much deadwork. Such was the annoying situation at the mine of the Saxton Coal Mining Co. operated in the No. IV coal just north of Terre Haute, Ind. During the months of warm weather it was possible to stand at any quiet spot in the mine and within 10 min. hear at least two or three falls,

Jan 1, 1931

By W. M. Weigel

LESS advances in the technology of non-metallic minerals than for several years past mark 1931, and the cause is easily found. The universal depression and decreased markets for non-metallic as well as other mineral commodities has forced the producers to cut out all unnecessary expense and reduce operating costs to a minimum in order to keep going, even on a reduced output, and to prevent insolvency. The result. has been that but 'little research has been carried on, and such as has been completed has in but few cases been put into commercial practice on account of the expense involved in new equipment and plant changes. The trend in the industry has been more economic than technologic, and the greatest effort put on market studies and sales attempts to expand markets and scrutiny of present operating 'practice leading to reduction of cost of production. This tendency has been increased by highly competitive conditions and the buyer's market which has prevailed and to the fact that price has been a greater factor than quality in placing orders. Only in cases where improvements in technology would immediately and effectively reduce costs or where in special cases there was but little competition with almost a monopoly control has actual technical development taken place.

Jan 1, 1932

By W. I. Garms, J. L. Stevens

BECAUSE of the many conflicting opinions regarding the functioning of the ball load and the characteristics of ball wear in ball-mill grinding, the following resume of reports covering recent tests conducted at the Hayden plant of the Kennecott Copper Corporation is submitted with the view of pointing out certain salient features that should throw additional light on the subject. MILLS USED Cylindrical drum mills with trunnion feed and discharge were used. The discharge trunnion was I3 1/2 in. in diameter. Dimensions inside the lining were 6 ft. 6 in. in diameter and 9 ft. 6 in. long. The mills were Britannia-lined and nine lifter bars projected 2 in. from the lining. The mill speed was 16 2/3 r.p.m. Feed to the mill was 9 per cent on 10-mesh, 85 per cent on 100-mesh, 77 per cent solids. New balls measured 2 in. in diameter and the approximate weight of the ball load was 40,000 pounds. INITIAL TEST During a test that was being conducted to determine the relative economic value of standard cast balls vs. forged steel balls in the local grinding operation, certain observations were made in regard to the functioning of the various ball sizes and the characteristics of ball wear, which warranted a supplementary test for the purpose of confirming such observations. For the initial test, the necessity for developing a graduated load of the new forged balls before the test could be started was realized, but the time required to obtain a graduated load and the functioning of the various ball sizes was not clear. No advantage could be seen for starting out with a full load of forged balls, as this initial load, at the least, would have to be completely ground out and replaced by daily additions of balls before the graduation could be complete and a normal static condition of ball sizes reached. For a considerable period prior to exhaustion of this initial charge there would be an unusual quantity of worn balls of a certain size, which would not be typical of a normal charge and could influence the characteristics and functioning of the entire load. Therefore, it was decided to start by daily addition of the forged balls to a mill that contained a normal operating load of cast balls. After 88 days of operation the mill was shut down for inspection. By that time the load consisted of a mass of forged balls functioning around a large core of the residual material of the former cast-ball load. This core of cast slugs, locally referred to as "the kidney," was well defined from the forged-ball load.

Jan 1, 1946

By W. A. Backofen, B. C. Wonsiewicz

The Plasticity transition in magnesium was studied by plane-strain compression of single crystals and polycrystalline material at temperatures from about 20" to 307°C. Reduction of single crystals along the c axis was accommodated by twinning on {1011) and retwinning on (10 12}, followed by basal shear in the doubly twinned volume. Deformation in that mode can result in sufficient independent shears for arbitrary shape change. Fracture in c axis compression, below about 100°C, has been related to excessive shear caused by unloading from the stress for {1011} twinning (-50 ksi at 20°C) to that for slip within the twin (-3 ksi); ductility follows from heating because the stress difference is lowered and the twin volume, in which elastic strain energy is dissipated on unloading, is increased. The stress for (1011) twinning is strongly temperature-dependent but not given by a critical resolved shear stress law. The latter is attributed to the influence of stress concentration from prior intersecting shear on nonbasal planes, the former to the temperature dependence of the preliminary slip. THE basic symmetry of hcp crystals has the effect of limiting the number of independent slip systems and making twinning an important deformation mechanism. The general result in wrought polycrystalline aggregates is a more or less sharply developed texture (or preferred orientation) which underlies a strong anisotropy in mechanical behavior. Knowing how the one influences the other is essential background for the use of such materials. Magnesium was of interest in this work because of the unexplained plasticity transition that it undergoes somewhere in the neighborhood of 200°c.''~ At lower temperatures plastic deformation before fracture in polycrystalline material is limited, while at higher temperatures extensive deformation is possible. The transition temperature commonly determines the lower limit of the range in which magnesium is worked. The limited ductility can be traced to a lack of independent crystallographic shears. A minimum of five are required for arbitrary shape change.' Around room temperature, however, slip on all known systems provides only four.' In each case, the slip direction is in the (0001) basal plane so that slip does not allow strain along the c axis. With increasing temperature, more slip occurs on the ( 1011) pyramidal plane and the ( 1010) prism plane but without change in direction.'?' Thus, that development alone cannot explain the transition temperature.

Jan 1, 1968

By C. A. Hartnagel

The year 1944 marks the eightieth anniversary of the discovery of petroleum by drilling in New York State. It was in 1864 that a half dozen shallow wells were drilled at Limestone in Cattaraugus County, in a region that now forms the northern extension of the 82,000-acre Bradford pool. These early wells found oil, but not in paying quantities. They did, however, attract attention to the district and were a factor in the development of the still active Bradford pool of Pennsylvania and New York. During 1943, the production of petroleum in New York amounted to 5,029,000 bbl. This represents a decrease over the previous year, in which 5,421,000 bbl. was produced. The flush production for the New York fields occurred in the early eighties shortly after the discovery of oil in the Richburg pool of Allegany County. During the flush period, production was in excess of five million barrels annually. By 1887, however, the output had decreased to an amount only slightly more than two million barrels, and through the early years of the present century the annual total was often less than one million barrels. Flooding of the oil sands for increasing productioil was made legal in 1919, and in 1927 the output once more reached the two million mark. Two years later it had increased to over three million barrels. In Table r is shown production since 1935, in which year for the first time the output under flooding methods was in excess of four million barrels. From this table, it is evident that oil production in New 'I'ork is rather well stabilized, and since most of the oil is obtained by the flooding, or water-drive, method, with little or no prospect of discovery of new oil territory, rapid changes in yield from year to year are not to be expected. In thickness, the oil sands have a maximum of about 50 ft., and by means oi flooding may produce 10 to 12 thousand barrels an acre and proportional amounts for thinner sands. In some cases, floods have been developed in sands only 12 ft. thick. Under good flooding conditions a yield of 2000 bbl. an acre is about the lower limit at which oil can bc produced at the present price of $3.00 a barrel. The average cost for the physical development ol a lease, not including the cost ol the lease itself, is $5000 an acre. Since several months must intervene before the flood begins to act on the oil wells, and a year or more is required to bring thc wells to maximum daily production, it is evident that a considerable interval occurs before maximum returns are realized. Once a flood is developed and the wells

Jan 1, 1944

By W. I. Garms, J. L. Stevens

Because of the many conflicting opinions regarding the functioning of the ball load and the characteristics of ball wear in ball-mill grinding, the following résumé of reports covering recent tests conducted at the Hayden plant of the Kennecott Copper Corporation is submitted with the view of pointing out certain salient features that should throw additional light on the subject. Mills Used Cylindrical drum mills with trunnion feed and discharge were used. The discharge trunnion was 13½ in. in diameter. Dimensions inside the lining were 6 ft. 6 in. in diameter and 9 ft. 6 in. long. The mills were Britannia-lined and nine lifter bars projected 2 in. from the lining. The mill speed was 162/3 r.p.m. Feed to the mill was 9 per cent on 10-mesh, 85 per cent on 100-mesh, 77 per cent solids. New balls measured 2 in. in diameter and the approximate weight of the ball load was 40,000 pounds. Initial Test During a test that was being conducted to determine the relative economic value of standard cast balls vs. forged steel balls in the local 'grinding operation, certain observations were made in regard to the functioning of the various ball sizes and the characteristics of ball wear, which warranted a supplementary test for the purpose of confirming such observations. For the initial test, the necessity for developing a graduated load of the new forged balls before the test could be started was realized, but the time required to obtain a graduated load and the functioning of the various ball sizes was not clear. No advantage could be seen for starting out with a full load of forged balls, as this initial load, at the least, would have to be completely ground out and replaced by daily additions of balls before the graduation could be complete and a normal static condition of ball sizes reached. For a considerable period prior to exhaustion of this initial charge there would be an unusual quantity of worn balls of a certain size, which would not be typical of a normal charge and could influence the characteristics and functioning of the entire load. Therefore, it was decided to start by daily addition of the forged balls to a mill that contained a normal operating load of cast balls. After 88 days of operation the mill was shut down for inspection. By that time the load consisted of a mass of forged balls functioning around a large core of the residual material of the former cast-ball load. This core of cast slugs, locally referred to as "the kidney," was well defined from the forged-ball load.

Jan 1, 1947

By W. I. Garms, J. L. Stevens

Because of the many conflicting opinions regarding the functioning of the ball load and the characteristics of ball wear in ball-mill grinding, the following résumé of reports covering recent tests conducted at the Hayden plant of the Kennecott Copper Corporation is submitted with the view of pointing out certain salient features that should throw additional light on the subject. Mills Used Cylindrical drum mills with trunnion feed and discharge were used. The discharge trunnion was 13½ in. in diameter. Dimensions inside the lining were 6 ft. 6 in. in diameter and 9 ft. 6 in. long. The mills were Britannia-lined and nine lifter bars projected 2 in. from the lining. The mill speed was 162/3 r.p.m. Feed to the mill was 9 per cent on 10-mesh, 85 per cent on 100-mesh, 77 per cent solids. New balls measured 2 in. in diameter and the approximate weight of the ball load was 40,000 pounds. Initial Test During a test that was being conducted to determine the relative economic value of standard cast balls vs. forged steel balls in the local 'grinding operation, certain observations were made in regard to the functioning of the various ball sizes and the characteristics of ball wear, which warranted a supplementary test for the purpose of confirming such observations. For the initial test, the necessity for developing a graduated load of the new forged balls before the test could be started was realized, but the time required to obtain a graduated load and the functioning of the various ball sizes was not clear. No advantage could be seen for starting out with a full load of forged balls, as this initial load, at the least, would have to be completely ground out and replaced by daily additions of balls before the graduation could be complete and a normal static condition of ball sizes reached. For a considerable period prior to exhaustion of this initial charge there would be an unusual quantity of worn balls of a certain size, which would not be typical of a normal charge and could influence the characteristics and functioning of the entire load. Therefore, it was decided to start by daily addition of the forged balls to a mill that contained a normal operating load of cast balls. After 88 days of operation the mill was shut down for inspection. By that time the load consisted of a mass of forged balls functioning around a large core of the residual material of the former cast-ball load. This core of cast slugs, locally referred to as "the kidney," was well defined from the forged-ball load.

Jan 1, 1947

By C. A. Hartnagel

The year 1944 marks the eightieth anniversary of the discovery of petroleum by drilling in New York State. It was in 1864 that a half dozen shallow wells were drilled at Limestone in Cattaraugus County, in a region that now forms the northern extension of the 82,000-acre Bradford pool. These early wells found oil, but not in paying quantities. They did, however, attract attention to the district and were a factor in the development of the still active Bradford pool of Pennsylvania and New York. During 1943, the production of petroleum in New York amounted to 5,029,000 bbl. This represents a decrease over the previous year, in which 5,421,000 bbl. was produced. The flush production for the New York fields occurred in the early eighties shortly after the discovery of oil in the Richburg pool of Allegany County. During the flush period, production was in excess of five million barrels annually. By 1887, however, the output had decreased to an amount only slightly more than two million barrels, and through the early years of the present century the annual total was often less than one million barrels. Flooding of the oil sands for increasing productioil was made legal in 1919, and in 1927 the output once more reached the two million mark. Two years later it had increased to over three million barrels. In Table r is shown production since 1935, in which year for the first time the output under flooding methods was in excess of four million barrels. From this table, it is evident that oil production in New 'I'ork is rather well stabilized, and since most of the oil is obtained by the flooding, or water-drive, method, with little or no prospect of discovery of new oil territory, rapid changes in yield from year to year are not to be expected. In thickness, the oil sands have a maximum of about 50 ft., and by means oi flooding may produce 10 to 12 thousand barrels an acre and proportional amounts for thinner sands. In some cases, floods have been developed in sands only 12 ft. thick. Under good flooding conditions a yield of 2000 bbl. an acre is about the lower limit at which oil can bc produced at the present price of $3.00 a barrel. The average cost for the physical development ol a lease, not including the cost ol the lease itself, is $5000 an acre. Since several months must intervene before the flood begins to act on the oil wells, and a year or more is required to bring thc wells to maximum daily production, it is evident that a considerable interval occurs before maximum returns are realized. Once a flood is developed and the wells

Jan 1, 1944

By T. A. Wright

THE SAMPLING of waste materials containing copper, lead and tin has taken on a new significance within recent years, and is of increasing importance, on account of the entry of some of the copper refineries into this field and the tendency towards consolidations among the smelters. In the past, such material was sold on the basis either of a rough or grab sample or of casual inspection of the lot. The two principal sources of this waste are the processes of fabrication and the scrapping of automobile, electrical, plumbing, railroad and other equipment. In both cases much material can be sorted, salvaged and sold by classification and grade to be melted "as is" or with the addition of new or virgin metal. The increasing care in classifying exercised in the large manufacturing plants tends to increase the proportion of this usable scrap; on the contrary, the increasing use of more complex and special non-ferrous alloys tends to make sorting and grading more difficult in turnings, borings, clippings, etc., and consequently is making sampling of more moment. In tin, lead, aluminum, and zinc furnace by-products such as ashes, drosses, skimmings, etc., the trade practice of evaluation has not varied much. For instance, tin drosses, battery lead, and aluminum skimmings are ordinarily sold on what is called "metallic button" or "metallic recovery" or "metallic yield." Copper and lead waste, however, is being sold more and more on actual copper and lead contents based on sample and chemical analyses. This paper will be devoted chiefly to the sampling of materials suitable only for refining and recovery of one or more of the metals present. The methods described are often based on the fact that but one metal, such as copper, is to be paid for. The loss of volatile constituents in melting does not appreciably affect the final copper result, as the "after-melting" assay can he readily calculated to the "before-melting" basis, but if smelter efficiency continues to increase, so that in time zinc, for instance, may be recovered on a paying basis, the method of sampling dirty brass, for example, will have to be changed also. As a matter of fact, we may expect that improved refining processes will make possible the partial recovery of lead and tin which are now lost.

Jan 1, 1928

By W. Rosotoker

Using an expression for the free energy of a homogeneous phase as a function of composition, a relationship is derived which interrelates the phase boundaries extending from the allotropic transformation of the solvent metal. Comparisons between observed and calculated phase boundaries in the systems Fe-Ni, Fe-Mn, Fe-W, Ti-Mo, and Ti-Cb are presented. IT is the purpose of this paper to illustrate how the general free energy equations for two phases in equilibrium may be used to derive an expression which interrelates the phase boundaries extending from the allotropic transformation of the solvent metal. The free energy per gram atom of a disordered solid solution may, for many purposes, be represented by the equation:' F = ½NZ [C-V,, + (1-C) VbB + 2C (l-C)V] + K(T) +RT[C-lnC+ (l-C)ln(l-C) ] [1] where N is Avogadro's number; Z, the coordination number; C, the concentration of the solute element in atomic percent; the subscripts refer to concentrations at phase mixture boundaries; VAA, VBB, and V,, are the bond energies between like and unlike adjacent atoms, respectively, at the interatomic spacing characteristic of the phase. The bond energies are usually assumed to be independent of small changes in the lattice parameter occasioned by solute additions and variations in temperature; V = VAB ---------------—— ; K(T) is the sum of the heat con- tent and heat entropy; R, the molar gas constant; and T, the temperature in degrees Kelvin. The free energy of a homogeneous phase is there- fore the sum of an internal energy, a specific heat, and a configurational entropy term, respectively. The compositions of two phases in equilibrium at a given temperature are governed by the minimum total free energy principle. Graphically, this is represented by the points of tangency of the tangent common to the free energy vs. concentration curves of the two phases. Analytically, this may be expressed as: ( df) = (df) [2] dc dc Expanding both sides using eq 1, the following equation is obtained after convenient readjustment of the terms: RT In[(ca)(1-c)]-½N (Vaa-Vbb)(Za-Zb) +NV [Za(l-2Ca)-Z,(l-2C,)] [3] The following assumptions have been made at this point: 1—The specific heats of the two phases are independent of composition variations within the range under consideration. Accordingly, the K(T) terms disappear on differentiation. 2— (Vaa)o = (VAA); (VBB). = (VBB); Va = V, Theyjustification for these assumptions can lie only in the successful application of the resultant equation. It may be noted that Zener2 has used assumption 1 in the calculation of the boundaries limiting the (a+j3) phase mixture in the Cu-Zn system.

Jan 1, 1952

By R. W. Guard

ALTHOUGH etching techniques have been developed for revealing dislocation sites in several metals and ionic crystals,h t is valuable to extend the technique to new metals. An etch pit method for nickel has been developed on the basis some suggestions of Dr. John R. Cuthill of the National Bureau of Standards who had observed etch pits in creep specimens of nickel. The etchant used was proposed first by wensch2 for revealing grain size in nickel. The present paper describes the evidence that the technique can be used to reveal dislocations and gives the conditions under which etching can be carried out. The specimens examined were vacuum melted high-purity Ni (99.985 pct Ni) and commercial "A" nickel (99.8 pct Ni). Both materials contained greater than 0.008 pet C and had been annealed in nitrogen or dry hydrogen at 1100o to 1200°C. This gave a grain size of 1.5 mm in the high-purity nickel and 0.050 mm in "A" nickel. Tensile specimens (0.254 in. diam) were deformed from 0.25 to 10 pct at room temperature and then heated for 1/2 hr at different temperatures from 400" to 900°C. The specimens were sectioned longitudinally then polished electrolytically in 60 pct H2SO4 and etched in 35 pct H3PO4 solution at 0.2 to 0.4 v for 30 sec to 3 min. The best method for setting the proper voltage for etching is to increase the voltage until gas bubbles are evolved vigorously from the specimen and then cut it back by 10 pct. It is necessary to heat the specimen above 500°C after deformation in order that etch pits will be formed. This "decoration" treatment permits carbon to segregate to the dislocation rendering them sensitive to etching. It was demonstrated that carbon was the decorating impurity by decarburizing some specimens in wet H2 at 1200°C. The susceptibility to etch pitting was lost following this treatment but could be restored by carburizing in contact with graphite. Some rearrangement of the dislocations in the as-deformed structure occurs on heating at 500oC and above so that the technique can not be used to study the nature of dislocation patterns in deformed specimens. Extended etching does not change the number of pits although the background becomes rough and the pits quite large. The polycrystalline specimens with various strains were examined after annealing at different temperatures. Typical patterns are shown in Figs. 1 and 2. In the unstrained specimen, Fig. 1, the density of pits is 2.5 X 10' per sq cm. All grains show pits regardless of their orientation although there is a

Jan 1, 1961

Dr. F. W. C. Schniewind, New York, N. Y.:—Mr. Vogel speaks of briquetting the flue-dust by means of lime. I learned recently in Europe of a process employed with considerable success at one of the blast-furnaces, where blast-furnace cinder is used with lime. The lime and cinder are mixed with the flue-dust, and exposed to superheated steam, which converts the blast-furnace cinder into cement. Briquettes are then formed in the usual way. Mr. Vogel :—The process referred to is the " Scoria process," which has not been in use for some time past. For that reason, I did not mention it. Prof. Arthur L. Walker, New York, N. Y.:—I would ask the commercial name for magnesium chloride, and where it can be obtained ? Mr. VoGel :—I mentioned magnesium chloride, because it has been used abroad to a large extent. In Germany it is obtained as a by-product in the manufacture of potash-salts; in the United States we have been using chloride of lime, which is cheaper. Otto Sussman, New York, N. Y.:—What is the cost of this process ? Mr. Vogel :—The cost is exceedingly low. I can give you the figures from abroad, but not for the United States, because the system has not -yet been used here commercially to

Jan 1, 1913

By K. A. Gschneidner, O. D. McMasters, T. J. O’Keefe

X-ray diffraction, differential thermal, ad rnetallo-graphic methods were used to establish the Dy-Pb Phase diagram. Lead additions lower the 1377°C transformation temperature of dysprosium to 1360°C leading to an inverted peritectic reaction. The 327°C melting point of lead is lowered by dysprosium additions to about 326°C yielding a eutectic reaction. A second eutectic reaction occurs at 13.3 at. pct Pb and 1200°C. The dysprosium-richest intermetallic compound DysPb3 melts congruently at 1695°C and crystallizes in the hexagonal Mn5Si3 (D8,) type structure. The peritectic decomposition temperatures for the remaining compounds are Dy5Pb, at 1555C, DyPb2 at 955C, and DyPb3 at 880°C. A fifth compound near the DyPb stoichiometry exists over a 310°C temperature range decomposing at 1130°C by means of an inverted peritectic reaction and melting incongruently at 1440°C. The crystal structures of the compounds are discussed. A systematic study of the rare earth-lead alloy systems is underway in an effort to supply information concerning the alloying behavior of the rare earth metals. The Dy-Pb phase diagram is the fourth system to be investigated in this study. The Yb-Pb,1 Y-Pb,2 and Eu-Pb 3 diagrams have been published recently. Utilization of the rare earth series of metals as a research tool in this manner should yield a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The lead used in this investigation was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The dysprosium was prepared in this Laboratory by the calcium reduction of the fluoride followed by distillation of the dysprosium. The major impurities in the dysprosium in ppm are: A1 (<40), Ca (400), Er (<50), Gd (<200), Ho (<200), Mg (<50), Si (30), Ta (400), Tb (<100), Y (<50), 0 (651, H (15), N (not detected), F (430), C (35). Alloy Preparation. Most of the alloys were prepared by melting weighed amounts of dysprosium and lead in sealed tantalum crucibles. The tantalum crucibles were sealed by are-welding in a He-Ar atmosphere welding chamber. Thus the alloys are in contact with He-Ar at about 1 atm pressure. Homogenization was achieved by holding them in the liquid state for about 1 hr, cooling, inverting the crucibles, remelting, and repeating the process at least twice. Since these alloys were prepared in sealed tantalum crucibles, chemical analysis for final composition was thought to be unnecessary. No detectable reaction of these alloys with the tantalum crucible was observed by metallographic examination. Metallographic evidence was also used to confirm the homogeneity of some of the alloys prepared in this manner. The compositions of a few alloys, which were prepared by nonconsum-able are-melting, were corrected for the small weight losses involved by assuming that the weight loss is due to vaporization of lead. The specimens obtained from the alloy samples were prepared under a dry-argon atmosphere because they were rapidly attacked by air and moisture. Thermal Analysis. Differential thermal analysis methods were used to determine the liquidus curves and reaction horizontals of the system. Both Pt vs Pt + 13 pct Rh and W + 5 pct Re vs W + 26 pct Re thermocouples were used to measure the temperature. An X- Y recorder was used to record the specimen temperature and differential electromotive force between the specimen and molybdenum standard. The arrest temperatures were measured potentiometri-cally. The accuracy limits (* values) associated with the reaction temperatures obtained by this method were estimated on the basis of both the reproducibility of the particular temperature value and the accuracy of the thermocouple at a given temperature. Liquidus temperatures were obtained from cooling arrest data while both heating and cooling arrest data were used to establish the horizontals of the diagram. Heat treatments during the thermal analyses of the alloys between 40 and 70 at. pct Pb were necessary in order to approach equilibrium conditions. The samples were held at temperatures between the various peritectic horizontals for l to 2 hr before the thermal analyses were continued. The entire range of compositions was investigated at the expense of a minimum amount of materials by adding appropriate amounts of lead to master alloys. More than sixty alloys were analyzed by this differential thermal method and for each alloy the results given herein are taken from two or three heating and cooling cycles. X-Ray and Metallographic Methods. Slice specimens for metallography and powder specimens for X-ray diffraction were prepared from rod-shaped samples which had been melted in sealed 0.62 5-cm-diam tantalum crucibles. The specimens were heat-treated in sealed tantalum crucibles which were protected by sealing them in argon-filled quartz ampules. Quenching was accomplished by breaking the ampules in ice water after heat treatment. X-ray powder specimens were sealed in 0.3-mm-diam glass capillaries under a dry-argon atmosphere. Copper, iron, and chromium radiation were used to obtain the powder patterns for these alloys. More than 150 powder patterns were obtained for specimens of various compositions and heat treatments. Included in these were several patterns for specimens which had purposely been oxidized. Patterns from specimens which had been accidentally exposed

Jan 1, 1969

By Smith Bracewell

First evidence of bauxite in Jamaica resulted from an analysis of a soil sample collected at Bull Savannah in 1938 during a systematic local investigation of the island&apos;s soil types. Results of subsequent work indicated the possibility of the occurrence of deposits of commercial grade and dimensions, and in 1942, with a view to emergency development of the deposits as a war measure, the Jamaican Government declared all bauxite in the colony to be Crown property.

Jan 10, 1958

By C. C. Wright, T. S. Spicer, R. G. Bowman

In recent years considerable publicity has been given to the problem of atmospheric pollution by fuel-burning equipment. Legislation has been stimulated and smoke ordinances have been enacted, the provisions of which show a definite trend toward stricter control of the emissions not only from the stacks of industrial fuel users but also from the chimneys of domestic consumers. As a result of war conditions, some slackening in the enforcement of these ordinances may be noted, but this is only a temporary expediency caused by the changes necessary in the distribution of the nation&apos;s fuel supplies and difficulties in securing the necessary equipment. Previous trends may be expected to continue in the postwar period. Largely because of the consumer demand for automatic heat, but partly because of the legislation against smoke emission, there has been a marked increase in the use of domestic underfeed stokers with the past decade. When correctly adjusted and operated, these units reduce the smoke emission materially, so that even the high-volatile bituminous coals may be burned with little or no emission of objectionable smoke. Unfortunately, however, the use of the domestic underfeed stoker introduces another problem; namely, fly-ash. Production of Fly-ash The term "fly-ash" is a misnomer, since the fly material is generally a mixture of small carbonaceous particles varying from green coal to coke, and inorganic particles ranging from fluffy ash to small particles of fused clinker. For want of a more comprehensive name, however, the term fly-ash is used throughout this paper to include all the fly material. Even with hand-fired furnaces a certain amount of fly-ash is produced, which necessitates periodic cleaning of the boiler flues or furnace radiator, the smoke pipe, and occasionally the chimney itself. With stoker operations the amount of fly-ash is increased many fold, because of the higher velocity of air travel through the fuel bed. Frequently the amount of this fly-ash attains such proportions as to constitute a definite nuisance to the householder and his neighbors and distracts very materially from the otherwise automatic or semi-automatic performance of the stoker. Virtually all the boilers and hot-air

Jan 1, 1944

By T. S. Spicer, C. C. Wright, R. G. Bowman

In recent years considerable publicity has been given to the problem of atmospheric pollution by fuel-burning equipment. Legislation has been stimulated and smoke ordinances have been enacted, the provisions of which show a definite trend toward stricter control of the emissions not only from the stacks of industrial fuel users but also from the chimneys of domestic consumers. As a result of war conditions, some slackening in the enforcement of these ordinances may be noted, but this is only a temporary expediency caused by the changes necessary in the distribution of the nation&apos;s fuel supplies and difficulties in securing the necessary equipment. Previous trends may be expected to continue in the postwar period. Largely because of the consumer demand for automatic heat, but partly because of the legislation against smoke emission, there has been a marked increase in the use of domestic underfeed stokers with the past decade. When correctly adjusted and operated, these units reduce the smoke emission materially, so that even the high-volatile bituminous coals may be burned with little or no emission of objectionable smoke. Unfortunately, however, the use of the domestic underfeed stoker introduces another problem; namely, fly-ash. Production of Fly-ash The term "fly-ash" is a misnomer, since the fly material is generally a mixture of small carbonaceous particles varying from green coal to coke, and inorganic particles ranging from fluffy ash to small particles of fused clinker. For want of a more comprehensive name, however, the term fly-ash is used throughout this paper to include all the fly material. Even with hand-fired furnaces a certain amount of fly-ash is produced, which necessitates periodic cleaning of the boiler flues or furnace radiator, the smoke pipe, and occasionally the chimney itself. With stoker operations the amount of fly-ash is increased many fold, because of the higher velocity of air travel through the fuel bed. Frequently the amount of this fly-ash attains such proportions as to constitute a definite nuisance to the householder and his neighbors and distracts very materially from the otherwise automatic or semi-automatic performance of the stoker. Virtually all the boilers and hot-air

Jan 1, 1944

By C. M. Moncrief, B C. Craft

A bentonite-clay drilling mud when treated with tetrasodium pyroarsenate underwent substantially the same reduction in viscosity and water loss as when treated with the complex phosphates. The complex arsenate showed a slightly higher reversion after heating; the other arsenates showed poor viscosity-reducing properties. Introduction During the past 10 years the chemical control of drilling mud has become of major importance in affecting the successful drilling and working over of wells. The desired properties of drilling mud have been well established, and in obtaining these characteristics there has developed a large market for viscosity-reducing chemicals. Viscosity reduction produced by humic acid, tannic acid, sodium silicate, sodium tannate, Calgon, and the complex phosphates has been described by Loomis, Ford, and Fidiam.l The effects Of treatment with complex phosphates and ammonium PolyPhosPhates on the rheological properties of muds were investigated by Fancher2 and the alkali vanadates have been described by Williams.3 Laboratory Investigations It is the purpose of this paper to point out the effects of arsenates in controlling the viscosity and gelling characteristics of a drilling mud. Viscosities and gel strengths were measured at room temperatures with a Stormer viscosimeter calibrated in centipoises and operated at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester at a pressure of I00 lb. per sq. in. for 30 min. The hydrogen-ion concentration was measured with a glass electrode. The bentonite-clay suspensions were prepared in the laboratory and allowed to age several days before testing. Members of the Arsenic Group in the periodic Table include arsenic, antimony and bismuth, but this investigation was limited to arsenic. Phosphorus also occurs in Group V of the Periodic system and phosphorus and arsenic form many closely related compounds such as pH3 and AsH3, P2O5 and As2O5, H3PO4 and H3AS04 Samples of tetrasodium pyroarsenate were prepared by fusing c.p. disodium arsenate (Na2HA5O4.7H2O). According to Friend,&apos; this re-forms the ortho-arsenate on dissolution in water. Sodium trihydrodiorthoarsenate was prepared as described by Mellor,5 from arsenic pen-toxide as follows: As2O5 + 3H20 -> 2H3AsO4 2H3AS04 + 3NaOH Na3H3(AsO4)2 .3H20 Sodium dihydrogen orthoarsenateWaHz-As04) was obtained by fusing together equivalent quantities of arsenious Oxide and sodium nitrate, dissolving the residue in water and allowing it to crystallize.

Jan 1, 1946

By S. Feuerstein, J. M. Galligan

SURFACE effects in the deformation of metal single crystals have been noted by a variety of workers.&apos; A large majority of these experiments have used surface roughening or a second chemical constituent at the surface. We performed the following experiment to see how the presence of a fine polycrystalline layer influenced the stress-strain behavior of single crystals of zinc. Spherical single crystals oriented for single slip were acid-machined into cylindrical dumbbell-shape shear specimens having a gage length of 3.2 mm and a cross section of 20 sq mm. The crystals were then deformed varying amounts at the surface of the gage section with emery paper. Following this treatment, the crystals were heated for approximately 8 hr at 200°C. This resulted in a polycrystalline surface layer, with an observed grain size of approximately 1/10 mm in diameter. Deformation of these crystals was undertaken at 78°K in pure shear, the shear direction <1120> lying in the basal plane. The deformation apparatus has been described elsewhere.2 The presence of a polycrystalline layer markedly raises the first observed plastic deformation, as can be seen from Fig. 1. This yield stress is then followed by a region of low work hardening comparable to that observed in shear tests on similar untreated zinc single crystals. However, the extent of easy glide is quite seriously curtailed, and is followed by a more rapid increase in work hardening, reminiscent of Stage II observed in the deformation of fcc crystals. The higher yield can probably be attributed to the difficulty of penetrating the grain boundaries by dis locations from sources interior to the boundaries. If we associate this yield stress with this breakthrough, then we might expect that more dislocations would be trapped in the crystal than is normally the case. If there is an increased density of trapped dislocations, this could lead to an increase in the amount of trapping with increasing strain, giving a larger strain hardening in the crystal. Although other explanations can be given, it is quite tempting to characterize the region of increased work hardening as a manifestation of Stage II-type deformation. This seems reasonable if the polycrystalline layer is quite efficient in holding up a large number of dislocations. In zinc crystals, since it is well-known that the slip distance can be as large as the specimen dimensions, one would only expect to entrap a large number of dislocation with very large crystals or by applying surface layers. If this interpretation of increased strain hardening is correct, it might present a method of studying Stage II in single crystals of zinc. This research was supported, in part, by the Office of Naval Research (1959). The encouragement and stimulation given by Professor E. R. Parker is gratefully acknowledged.

Jan 1, 1965

By C. H. North, L. E. Lynd, W. W. Anderson, H. Sicurdson

D. R. Grantham (Institute of Mining and Metallurgy, London, England)—This paper is a very valuable contribution to our knowledge of ilmenite and its alteration products. Two aspects are not treated in the paper and further information would be valuable. How far are the alteration processes described influenced by the original composition of the ilmenite? The word gangue is used but it is not clear whether this refers to other chemical constituents in the ilmenite, e.g., magnesia, or to other minerals loose or in composite grains. Has the work described been related to specific gravities? Pure ilmenite is stated to have a specific gravity of 4.79. Some varieties range up to over 5.0, while high magnesic varieties have a specific gravity ranging to below 4.2. Alteration to hematite might lower the specific gravity and a porous texture due to the removal of iron and the formation of rutile might also lower it. As specific gravity is a quick method which often gives an approximate indication of composition, data on the above would be valuable. L. E. Lynd (authors&apos; reply)—Because of the way in which beach sand deposits were formed, it is impossible to tell exactly what the original composition of the parent ilmenites might have been. Information on the influence of original composition on the alteration processes must be derived from other sources, perhaps by comparing the alteration products formed from ilmenite in place in a variety of rock deposits, where parent ilmenite and its alteration product can be recognized. No information of this type has yet been brought to our attention. The material referred to as gangue includes all constituents other than oxides of titanium and iron. Nearly all of this was present as separate grains of garnet, augite, hornblende, quartz, feldspar, spinel, or other gangue minerals. Inclusions of gangue minerals within ore grains were rare, and we believe there is little MgO (1 pct or less) or other impurity actually held in the ilmenite structure in any of the concentrates studied. No specific gravity measurements were made on the samples studied. However, the suggestion that alteration involving loss of iron would lower the specific gravity is a very reasonable one, and is in accord with the findings of Creitz and McVay (Ref. 9 of our paper) who reported two magnetic opaque fractions from Trail Ridge, Fla., to have the following specific gravities and pompositions: The specific gravity of this porous, high TiO² alteration product of ilmenite is closer to that of rutile (4.25) than to that of ilmenite. Due to the porosity, it may even be less dense than rutile, although lower in TiO² and higher in iron.

Jan 1, 1955

By C. M. Moncrief

A bentonite-clay drilling mud when treated with tetrasodium pyroarsenate underwent substantially the same reduction in viscosity and water loss as when treated with the complex phosphates. The complex arsenate showed a slightly higher reversion after heating; the other arsenates showed poor viscosity-reducing properties. Introduction During the past 10 years the chemical control of drilling mud has become of major importance in affecting the successful drilling and working over of wells. The desired properties of drilling mud have been well established, and in obtaining these characteristics there has developed a large market for viscosity-reducing chemicals. Viscosity reduction produced by humic acid, tannic acid, sodium silicate, sodium tannate, Calgon, and the complex phosphates has been described by Loomis, Ford, and Fidiam.l The effects Of treatment with complex phosphates and ammonium PolyPhosPhates on the rheological properties of muds were investigated by Fancher2 and the alkali vanadates have been described by Williams.3 Laboratory Investigations It is the purpose of this paper to point out the effects of arsenates in controlling the viscosity and gelling characteristics of a drilling mud. Viscosities and gel strengths were measured at room temperatures with a Stormer viscosimeter calibrated in centipoises and operated at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester at a pressure of I00 lb. per sq. in. for 30 min. The hydrogen-ion concentration was measured with a glass electrode. The bentonite-clay suspensions were prepared in the laboratory and allowed to age several days before testing. Members of the Arsenic Group in the periodic Table include arsenic, antimony and bismuth, but this investigation was limited to arsenic. Phosphorus also occurs in Group V of the Periodic system and phosphorus and arsenic form many closely related compounds such as pH3 and AsH3, P2O5 and As2O5, H3PO4 and H3AS04 Samples of tetrasodium pyroarsenate were prepared by fusing c.p. disodium arsenate (Na2HA5O4.7H2O). According to Friend,&apos; this re-forms the ortho-arsenate on dissolution in water. Sodium trihydrodiorthoarsenate was prepared as described by Mellor,5 from arsenic pen-toxide as follows: As2O5 + 3H20 -> 2H3AsO4 2H3AS04 + 3NaOH Na3H3(AsO4)2 .3H20 Sodium dihydrogen orthoarsenateWaHz-As04) was obtained by fusing together equivalent quantities of arsenious Oxide and sodium nitrate, dissolving the residue in water and allowing it to crystallize.

Jan 1, 1946