Search Documents

By Jacques B. Wertz

Both the San Andreas fault complex and the Murray fracture zone are apparently found to be contemporaneous with the Laramide mineralization period. Their compounding effects certainly have disturbed the Texas lineament belt and its components with serious lateral offsets and most probably have been instrumental in allowing intrusives to be emplaced as well as mineralization to accompany these intrusions at some of the fracture intersections. While the main fracture centers can be almost accepted as being structurally linked together, the Texas lineament trend definitely predominates, exerting a prevailing direction to graben (Silver Bell) and to elongated depressions (Bisbee). That this lineament belt also influenced the concomitant mineralization seems a logical inference. The orebodies are generally found at intersections near the most centrally-located intrusive with a distance varying from contiguity to one or two miles. The Southeast Arizona copper province owes its existence primarily to a particularly favorable structural setting of broad semi-continental scope. Thus, various regional structural elements are to be considered as possibly direct or remote cause for the widespread mineralization, although the one or the ones really responsible may never be singled out. There arc three basic regional elements: (1) The north-northwest-trending anticlinorium that diagonally crosses Arizona is quite obvious because many mountain ranges follow this direction. This anti- clinorium, which merges northward into the Wasatch-Jerome Belt, marks a broad zone of weakness where tension seems to prevail. Mineralized trends such as Jerome-San Manuel-Bisbee may give some weight to the economic value of this structural element. (2) Northeast-trending fractures, parallel to the Colorado Mineral Belt (Landwehr, 1967), appear troincident with mineralization as evidenced by the Questa-Grants-Morenci and the Lordsburg- Tyrone-Santa Rita alignments. This structural direction is accepted as one of the most economically significant in the Southwestern United States. (3) The Texas Lineament.

Jan 1, 1970

By D. W. Fuerstenau

On page 1243, column 1, the first line of the author's reply should read "D. W. Fuerstenau (author's reply)---," rather than D. E., as printed. In the sentence immediately preceding the first equation (page 1243, column 2)' the word "none" was omitted. The sentence should read: "However, if enough ore is put into the mill [so] that none of the energy put into the mill is wasted on metal-to-metal impact, then the product should have size modulus determined by the relation: ..."

Jan 1, 1961

THOSE NOT MARKED ARE MEMBERS; MARKED THUS t ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. JUNIOR MEMBERS ARE MARKED II. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. AARONS, J. BOYD, Genl. Mgr., Chaffers G. M. Co., Boulder City, West. Australia. '05 ABADIE, EMILE R., Min. Engr Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Genl. Supt., Iron Mines Div., 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, J. W., Min. Engr., "St. Omer," 123 N. Grand Ave., Los Angeles, Cal. '94 ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. '15 ABBOTT, ROBERT R., Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Yamagano G. M., Satsuma-Gori, Satsuma, Japan. '14 || ABRAHAMS, A. I., Student 1391 Madison Ave., New York, N. Y. '14 tACKER, E. O'C., Met Bethlehem Steel Co., Bethlehem, Pa. '86 ACKER, LOUIS K., JR., Min. Engr 565 Highland Place, Bellevue, Pa. '08

Jan 1, 1917

By W. P. Sykes

ThiS investigation was undertaken primarily to establish the relations existing between temperature and mechanical properties in molybdenum, nickel, and an aluminum-copper alloy. Mlolybdenutn (m.p. 2500" C.) was chosen because it is partly similar to tungsten and partly similar to the common ductile metals. Also it is known to furnish, by proper treatment, a desirable material to use in studying relation of grain size and physical properties. The molybdenum used was of the quality that is drawn into wire 0.003 in. in diameter for use as filament supports in incandescent lamps; Chemical analysis shows less than 0.1 per cent. of impurities. Nickel belongs to the same class as iron. Its melting point is 1450" C. and an allotropic change at about 370" C. results in a loss of magnetism above that temperature. This feature made nickel doubly valuable for the purposes of these tests. The nickel used was obtained from the Driver-Harris Co. as 0.090 in. (2.3-mm.) wire, annealed; analysis showed 99.8 per cent. nickel and 0.150 per ccnt. iron. Aluminum is one of the low melting-point metals. Some tensile tests at clevated temperatures have been reported by Bengough but the possibility of learning more with the low temperature and sensitive apparatus available rccommendcd this metal. The samples marked A1 arc an aluminum-copper alloy that contains 3 per cent. copper, 0.42 per cent. iron, and 0.21 per cent. silicon. The presence of the copper somewhat coniplicates the analysis of the results; but the action of copper in aluminum has been studied so that its influence might have been foretold, in part at least. The material and analyses were furnished by the Aluminum Castings Co. The nickel wire, which was deformed at 400" C., was drawn under a bath of molten lead and through a die, which also was immersed in the bath. A thermocouple was suspended in the molten metal to indicate the temperature. Hot oil was uscd as the heating bath for drawing the

Jan 1, 1921

In the January Bulletin a list was published of Societies' publications, magazines, etc., which were duplicates and were discarded at the time of-the consolidation of the libraries of the three Founder Societies. A second list published herewith includes text books which are duplicates and which will be disposed of about April 1, 1916, by the Board of Directors of the Institute through the, Library Committee.. If, meanwhile, members desire to secure some of these books, they are asked to communicate at once with the Secretary as. this is an unusual opportunity to secure books at an extremely low price. Airy, George Biddell.-Magnetism, London, 1870, Bd. Alberti, Friedrich von.-Halurgische geologic. Erster Band. Zweiter Band. Stuttgart, 1852, Bd. American Iron and Steel Association.-Ann. Rep. of the Sec'y. Statistics of American and, Foreign Iron Trades, 1877. Phila., 1877, Bd. Same, for year 1878. Phila., 1879, Bd. American. Telephone and Telegraph Co.-Ann. Rep. of Directors to Stockholders, 1911. N. Y., 1912, paper. Armagnat, H.-Induction Coils. Trans. by Otis Allen Kenyon, N. Y., 1908, Bd. Armstrong Cork Co. Insulation Dept. Nonpareil Corkboard Insulation. Pittsburgh, 1909, Bd. Associazione fra gli Industriali Metallurgici Italian.-The Metallurgic industry of Italy. Description of some of the principal works. Milan, 1911, Bd.

Jan 2, 1916

By Joseph Jensen

MANY fields have been zoned by nature with shales and intermediate waters between oil zones. Limitations thus imposed have been the basis on which the field was developed. In contrast thereto, in the Ventura Avenue Field, nature proved more generous. Always expecting to find such similar limitations, operators drilled deeper and deeper into the oil zone without finding any distinctive shale bodies other that the Gosnell shale and only one intermediate water, which became the point below which the final water shut-off of each well was made. Thus, on top of the structure, about 3300 ft. of oil-bearing zone has been penetrated below this intermediate w9ter-a distance of 4000 ft. below the Gosnell shale. At first it seemed that the greater the penetration in the zone, the better the well. The error of this assumption became evident

Jan 1, 1930

By B. M. Larsen, K. Heindlhofer

Jan 1, 1945

By W. R. Clark, W. W. Cotter

Jan 1, 1946

By W. W. Cotter, W. R. Clark

Jan 1, 1946

By M. L. Fuller

MOST commercial alloys undergo changes in phase composition after casting. This is a natural result of the fact that the alloys are not in a state of phase equilibrium as cast and phase changes will therefore take place, with more or less rapidity, in an attempt to attain equilibrium. The practical aspect of aging in zinc-alloy die castings concerns the changes in physical properties and in dimensions that may accompany aging phase changes. Harmful alterations have been reduced to a minimum and zinc-alloy die castings are being produced today that are so stable with respect to dimensions and physical properties that they are entirely suitable for most practical purposes1. In the first paper2 of this series, and in this paper, aging phase changes of zinc alloy die castings have been investigated and the possible influence of these changes on dimensional changes of the castings has been evalu-ated and compared with the dimensional changes actually experienced. The change of dimensions has been selected for practical comparison in these papers because the effect of phase changes on the dimensions of a casting is directly calculable; from X-ray crystal-analysis data of the phase structure. The die-casting alloys considered contain, in addition to zinc, 4 per cent of aluminum, about 0:03 per cent magnesium, and from 0 to 3 per cent of copper. It was shown in the former paper that the eutectoidal decomposition of the beta aluminum-zinc phase, while intrinsically capable of causing a considerable shrinkage, can have very little effect on the observed shrinkage of die castings because it takes place within a few days of aging, whereas the observed shrinkage continues for five weeks. It was therefore concluded that the other existing phase change,

Jan 1, 1935

By N. N. Breyer

A specially built "hard" tensile machine with characteristics permitting the precise detertnination of the drop of the load at the yield point has been used to study the magnitude of the yield-point phenotnenon in prestrained martensitic 4340 steel. A new phenonzenon, the appearance of a secondary yield point, has been observed by holding the specimen at constant strain in the plastic region. Furthermore, it has been found that a series of yield-point drops could be introduced by successive constant strain holds in the plastic region. The isothermal kinetics of the development of the secondary yielding point lave been studied at four temperatures: 24° 0° -18°, and -79°C. From the results of the kinetic investigation, equations for the In a previous investigation1 it was shown that, contrary to generally held opinion, steels of medium carbon content, such as 4340, 4140, and 86B30, in the as-quenched martensitic condition, can be cold-drawn through a die with reductions in area of up to 10 pct without cracking. Tensile specimens of 4340 machined from bars quenched and prestrained in this manner exhibited tensile strengths of about 400,000 psi coupled with 30 pct reductions in area. In addition, it was found that each sample of such steels exhibited a yield point in the quenched, cold-drawn condition. Since these studies were conducted on a commercial hydraulic testing machine of a type which is not well-suited to detailed study of yield-point behavior, it was decided to study this phenomenon more thoroughly on a rigid straining machine. In this new investigation, use of such a "hard" machine not only allowed study of the magnitude of the yield-point drop but also revealed a new phenomenon—secondary yielding of the martensite introduced by stopping crosshead motion after plastic deformation of the sample had begun. The present paper is a report of these findings. MATERIALS AND PROCESSING The material used was a commercial 4340 steel of the composition shown below: 0.41 0.80 0.013 0.019 0.31 0.85 1.76 0.28 1 0.42 0.77 0.015 0.024 0.30 0.84 1.69 0.28 0.08 2 1 = Ladle analysis. 2 = Laboratory analysis. Bars of this steel were processed in the following way: 1) machined to predetermined diameters; 2) austenitized at 870°C for 1 1/2 hr; 3) oil-quenched; 4) cooled to -115°C for 1/2 hr; onset and increase in magnitude of the secondary yielding in this temperature region have been found to fit the relationship ?Ys = Atn where ?Ys is the magnitude of the secondary yield Point in psi, t is the time in seconds, and A and n are parameter characteris-tics of the material. Although the occurrence of the primary and secondary yield points could be rationalized qualitatively on the basis of stress-induced ordering of carbon atoms in the stress fields of dislocations, as postulated in an earlier paper, the kinetics of the secondary-yield-point development were interpreted to indicate that the ordering involves more than just single jumps of carbon atoms from high-energy to neighboring low-energy sites. 5) pickled and lime-coated; 6) drawn through a carbide die. The predetermined diameters were chosen so that drawing through the same die gave the various reductions desired. Tensile specimens of 0.252 in. diam with a 1 1/4 in. gage length were then prepared from the drawn bars and tested. In order to study the stress-strain behavior at the yield point in detail, a rigid tensile machine with a high spring constant was constructed. Columns of large cross section (relative to the specimen cross section) constituted the machine frame. A dc motor was used to drive a screw via a gear reducing train and a "crane" thrust bearing. In this relatively simple device small deformations could be observed un-blurred by the slow response and lower spring constant inherent in hydraulic machines.' A strain-gage dynamometer permitted load changes as small as 8 lb to be read. RESULTS Tensile test samples machined from bars in the as-quenched condition with no subsequent drawing and samples from bars with 3.8 pct reduction after quenching gave stress-strain curves typified by those shown in Figs. I and 2. The time lapse between predrawing and tensile testing varied but usually ranged between 3 to 6 days at room temperature. The strain rate during testing was 0.003 in. per in. per min. The as-quenched curve is seen to have a broad serrated maximum whereas the stress on the specimen prestrained 3.8 pct rose linearly to point A, Fig. 2, fell abruptly to B, and then gradually to C. The abrupt drop to B was accompanied by evidence of incipient necking. The drop of the stress at the yield point in the prestrained samples (A to B in Fig. 2) changed with the percent prestrain, as illustrated on Fig. 3. Although the tensile strength increased continuously with the amount of previous cold drawing, the magnitude of the yield point drop first increased—up to about 6 pct prior reduction—and then decreased. Specimens from bars predrawn more than 8 pct broke in a brittle fashion in the elastic portion of the stress-strain curve.

Jan 1, 1967

By Fred Witt, Milton Schwartz

ESTABLISHED methods for obtaining quantitative pole figures for flat sheets1"5 can be extended to apply to thin films on a substrate. The mode of scanning the sample is exactly the same as described in the references? but consideration is given to the fact that the scattered X-ray intensities are due to both the thin film and its substrate with appropriate attenuation factors. The purpose of this paper is to describe a method to obtain the scattered intensities from the film alone for subsequent pole-figure determinations. Fig. 1 shows the four possible general positions of the film (f) and its substrate (s) with respect to the incident X-ray beam (I,). In this paper it will be assumed that the plane of the sample is normal to the plane of the diffractometer. In the diagrams the line jV is the normal to the flat sample and the line P is the trace of the diffracting crystallographic planes in the plane of the diffractometer. The angle of tilt, a, is the positive acute angle measured from the line N to the line P; if this angle is measured clockwise then a is said to be in the positive a region; if this angle is measured counterclockwise then a is said to be in the negative a region. For the reflection cases, the total scattered intensity, at the proper Bragg angle for a particular set of planes, is due to that scattered by the film Vf) and that scattered by the substrate. The beam incident on

Jan 1, 1967

By C. H. Wilson, J. W. Daly, J. J. Jakosky

Meteor Crater, Arizona, is a natural wonder which for years has been the subject of considerable discussion and study as to its origin and age (Fig. 1). Of the various theories advanced regarding the origin, two have been considered as most probable by a majority of investigators. The first theory is that the crater was formed by a meteorite or a swarm of meteoric material striking the earth at a high velocity and burying itself. The second theory is that the crater was formed by a "steam explosion" from hot solutions or gases coming from underneath the present sedimentary beds which overlie the area. In order to obtain more detailed information regarding the conditions existing at the crater, the present management decided to have a detailed geophysical examination made. The origin of the crater is of considerable scientific importance and interest. More or less active mining operations have been carried out during the past 20 years by various groups who believed that the crater was of meteoric origin, and who hoped that sufficient quantities of such material had been buried to be commercially valuable. Fragments of meteoric material found on the surface of the ground in the debris around the rim gave analysis of approximately 92 per cent iron and 8 per cent nickel, with some platinum and iridium. The material having a gross value of approximately $50 per ton, mining would be commercially profitable if sufficient quantities of the material existed in condition for mining. In the early work numerous drill holes and shallow shafts were put down, mainly in the northern portion of the crater. Pulverized material and debris caused considerable difficulty, and in an effort to overcome this the present management started a 1500-ft., two-compartment shaft on the south rim of the crater and outside of the fill zone. The intention was to sink the shaft in the solid rock outside of the crater, and then to crosscut toward the crater at a depth of 1500 ft. The work was finally stopped when a depth of 650 ft. was reached, because water poured into the shaft through large cracks and fissures in the rock. The enormous force responsible for the crater had also broken

Jan 1, 1932

By Zay Jeffries

Tungsten has the highest melting point of all the known metals, namely 3350 C.; it is one of the hardest of the metals; it has the highest equiaxing or recrystallization temperature after strain hardening, of any pure metal known. It is particularly distinguished because, when composed of small equiaxed grains, it is extremely brittle and fragile at room temperature, and when possessing a fibrous structure it may be ductile and pliable at room temperature. The common ductile metals act in exactly the opposite manner in this respect. The present paper will include a brief note regarding the manufacture of wrought and ductile tungsten. The metallography of wrought and ductile tungsten in the various stages of manufacture will be considered more or less in detail. The general relationships between the properties of tungsten and other metals will also be considered. A discussion will be given explaining why fibrous tungsten is ductile at room temperature, even though past experience with other metals would indicate that it should be brittle. Finally, a brief note regarding some new fundamental metallographic propositions relating to all metals will be given. Manufacture of Wrought and Ductile Tungsten Up to about 10 years ago, it had not been possible to work tungsten mechanically. About the year 1908, Dr. William D. Coolidge, of the General Electrie Go., produced ductile tungsten from what was then supposed to be an inherently brittle metal and which, in fact, was inherently brittle in its normal state, that is, when composed of equiaxed grains. Since that time many products, chief among which are the filaments for electric incandescent lamps, have been made from wrought and ductile tungsten. Tungsten is produced chiefly from the minerals wolframite and scheelite.1-8 The ores may be reduced in many ways. For example, the ore may be fused with alkali carbonates and the fusion dissolved in water; sodium tungstate is formed, which is soluble in water. This

Jan 1, 1919

By Bert Sandell

MUCH has been said and written about the various uses of die-castings, their applications in the various industries and their advantages and disadvantages. Examination of this literature, however, fails to disclose any data concerning the effect of temperature upon any of the physical properties of die-casting alloys. The uses and applications of die castings are so numerous, and of such a varied nature, that far too lengthy a manuscript would be required to list all of them. Brief mention of some specific cases will suffice to illustrate the temperature ranges in which certain die castings function. Automobile hardware, such as hub caps, door handles, radiator caps, etc., can be used as one example. Castings of this type are constantly exposed to varying climatic conditions, temperatures ranging from below zero to upwards of 100° F. Refrigerator parts, such as ice-cube trays, etc., form another example. Approaching the other temperature extreme, we encounter conditions such as are found in kitchens in which oven-heat indicator parts, cooking utensils, waffle grids, etc., embody use of die castings, where temperatures as high as 500° F. are often met with. Because of this variation in service temperatures, it was felt necessary to ascertain the effect of these temperatures upon the physical properties of die-casting alloys. The Charpy impact test was chosen first because of its simplicity, and because of the fact that brittleness is more likely to be objectionable in die castings than hardness or other physical properties.

Jan 1, 1932

By F. Lowell Lawrance

JOHN SMITH, citizen of the U.S.A., has become so accustomed to reading that Congress has appropriated billions of dollars to pay war costs. that he no longer is impressed by relatively small figures, such as several hundred thousand or a few million, in connection with Government departments.

Jan 1, 1944

By G. W. Josephson

JUDGING by the progressive atmosphere prevailing in the nonmetallic mineral industries during the past year, postwar conditions were healthful though inflationary. Demand for most industrial mineral products has been exceptionally high and many new production records were attained. Severe shortages of some commodities existed, especially building materials and fertilizers. Production costs and prices increased and profitable operation was general. Under these conditions expansion programs were the order of the day. Ample funds were available to finance the purchase of good equipment; and, as wages and other operating costs were increasing, primary emphasis was placed on attaining maximum efficiency in new installations. These efforts were hampered by shortages and slow delivery of desirable equipment, so compromises in design were often necessary. However, on the whole, production practice improved.

Jan 1, 1948

By Paul M. Tyler

MUCH has been said in print, and much more that was unprintable, about burdensome controls, taxation, and multiplying restrictive, regulatory, or taxing activities of the Federal Government, but not so much has been said about ways and means whereby the Government can and does render economic assistance. Economics has been defined as the study of men earning a living, and economic assistance to industry as well as to individuals properly should take the form of helping enterprisers to help themselves rather than charity. Proposals to have the Government play Santa Claus must be examined carefully if -only to avoid undue favoritism to politically important persons and downright venality by potentially crooked public officials. Thomas Jefferson is credited with the remark that the best government is the one which governs least. Paternalism is abhorrent to most Americans.

Jan 1, 1947

By Salinger, Herbert

WITH the large amount of metallurgical re- search work now being done and the constant effort of the engineer to effect economies of operation, I think it is a safe prediction that the next few years will see a great change in the handling of mine products. The well-managed mine, with sufficient ore reserves to warrant the necessary plants, will increasingly call upon the metallurgist and chemist for the solution of its problems. Shipping sorted ore or concentrate to the nearest smelter will not be the course followed. From ore to metal, or at least to a product directly salable to the consumer, will be the practice followed. As a consequence, mine managers will be increasingly interested in metal trade problems. By metal trade I mean the buying, selling, shipping, handling, and all the practices, forms and customs that go to make up the trade.

Jan 1, 1928

By AIME AIME

In the present number of Mining and Metallurgy, issued on the fiftieth anniversary of the founding of the Institute, it appears appropriate to chronicle a few of the interesting incidents respecting its early life. We are fortunate in being able to cull the following notes from unpublished manuscripts of Doctor Raymond and Doctor Drinker, than whom no other members could have written with greater exactness and fidelity. THE seventh decade of the 19th century may be said to have marked an. era in the history of the world. Industrially and .commercially it was marked by the wide application and utilization of discoveries already made, which came to their full effect at this period in steamships, railways, telegraph and cable lines; the standardization of parts in machines, from watches to locomotives; the use of 'dynamite, antiseptic surgery, the open-hearth steel process, the compressed-air rock-drill, the electric generator, and the Gatling gun. Through the opening of the Suez canal in 1870 the maritime trade of the world was revolutionized, sailing vessels were supplanted by steamers, while ocean cables and ocean "tramps" brought about far more rapid movement of commerce than had before been experienced. Politically, this period was marked by the sudden birth of the German empire and the beginning of that intensive internal development of the national resources of that empire in preparation for colonial extension and war, the amazing result of which has been made evident by the recent world conflict. In the United States, the significance of this decade was peculiarly important. The re-admission to the union of Virginia, Mississippi, Texas and Georgia in

Jan 1, 1921