Search Documents

By David A. Keys

The object of this investigation was to determine with a vertical magnetic variometer the extent of the titaniferous ore deposit that occurs not far from Ivry in Terrebonne County, Quebec, about 70 miles north of Montreal. The Ivry mine, on lots 37 and 38 of range V, Beres-ford township, Quebec, is one of the largest and most accessible to transportation of the deposits of ilmenite in Quebec. The ore consists of an aggregate of ilmenite anhedra serving as host for numerous fine plaques of hematite. No magnetite is known from any occurrence near this lot, and in this way the deposit differs from many others that contain a large percentage of magnetite with the ilmenite. The deposit at Ivry thus has much lower magnetic susceptibility than those containing abundant magnetite, and a sensitive magnetometer was necessary for the work, although a body of magnetite with ilmenite about a mile from the Ivry mine was successfully prospected with a dip needle. The principal orebody is exposed in a quarry known as the Ivry mine, from which about 16,000 tons of ore have been shipped. Small exposures of ilmenite isolated by drift serve to show the presence at the surface of some of the bodies indicated by the magnetometer, but most of the hill is covered with glacial till and second growth hardwood. At the lower levels the till gives place to fluvioglacial sands and gravels from which the forest has been cleared. The increasing thickness of the sand and gravel as the hill descends makes the tracing outward of the deposits from the rocky knob of anorthosite a difficult matter. Within the orebodies too, some masses of anorthosite persist, which may account for some local irregularities. Fig. 1 is a photomicrograph, taken by reflected light, of a typical specimen of the ore. The dark patches are hematite and the light parts are ilmenite No trace of magnetite was found. Pig. 2 is a photomicrograph of a thin section of the country rock showing the texture of the anorthosite. The mean of four analyses quoted by Robinson1 is: titaninm, 19.26 per cent; iron 45.41 per cent. The ilmenite ore is not sufficiently magnetic to deflect an ordinary compass needle, but the effects of the induced magnetism in the ore by

Jan 1, 1940

By David A. Keys

The object of this investigation was to determine with a vertical magnetic variometer the extent of the titaniferous ore deposit that occurs not far from Ivry in Terrebonne County, Quebec, about 70 miles north of Montreal. The Ivry mine, on lots 37 and 38 of range V, Beres-ford township, Quebec, is one of the largest and most accessible to transportation of the deposits of ilmenite in Quebec. The ore consists of an aggregate of ilmenite anhedra serving as host for numerous fine plaques of hematite. No magnetite is known from any occurrence near this lot, and in this way the deposit differs from many others that contain a large percentage of magnetite with the ilmenite. The deposit at Ivry thus has much lower magnetic susceptibility than those containing abundant magnetite, and a sensitive magnetometer was necessary for the work, although a body of magnetite with ilmenite about a mile from the Ivry mine was successfully prospected with a dip needle. The principal orebody is exposed in a quarry known as the Ivry mine, from which about 16,000 tons of ore have been shipped. Small exposures of ilmenite isolated by drift serve to show the presence at the surface of some of the bodies indicated by the magnetometer, but most of the hill is covered with glacial till and second growth hardwood. At the lower levels the till gives place to fluvioglacial sands and gravels from which the forest has been cleared. The increasing thickness of the sand and gravel as the hill descends makes the tracing outward of the deposits from the rocky knob of anorthosite a difficult matter. Within the orebodies too, some masses of anorthosite persist, which may account for some local irregularities. Fig. 1 is a photomicrograph, taken by reflected light, of a typical specimen of the ore. The dark patches are hematite and the light parts are ilmenite No trace of magnetite was found. Pig. 2 is a photomicrograph of a thin section of the country rock showing the texture of the anorthosite. The mean of four analyses quoted by Robinson1 is: titaninm, 19.26 per cent; iron 45.41 per cent. The ilmenite ore is not sufficiently magnetic to deflect an ordinary compass needle, but the effects of the induced magnetism in the ore by

Jan 1, 1940

By R. E. Wade

THE Butte, Anaconda & Pacific electrification is of peculiar interest, in an incidental way, to the entire mining fraternity, and especially the engineering branch, not only in this great Northwest country but throughout the entire Western mining country, which is rich in minerals and water power. It is probably fair to say that the prime object of mining and smelting engineering is to reduce the cost of production, and in the case in hand the relative location of mines and smelter brings the cost of transportation of ore to the front. While some might assign this item to the railway people, it is inseparably a part and parcel of the general scheme of the production of metal from the ore. In considering the electrification of the B., A. &. P. railway the mining and smelting engineer, above all, wants to know what saving will be effected by the change in motive power. Unfortunately the new power has been in use during a very limited period and on the Smelter Hill section of the road only, and no reliable data, from actual service conditions, can be obtained until the entire electrified section has been in service for a reasonable length of time. Any remarks on this subject at the present time, therefore, must of necessity be general in nature and more or less descriptive. The railway, electrical and mining worlds and the country in general are indebted to the B., A. & P. railway for the pioneer work it is now doing, as it undoubtedly marks the beginning of the electrification, within the comparatively near future, of all transcontinental roads between the Missouri river and the Pacific coast. Together with this goes the development of an untold wealth in water power and all natural resources within the same territory. For the first time in the history of electric railway work, in this country, direct current at a potential of 2,400 volts is being used. With this potential there is a great saving in transmission of energy to the locomotives and there are only two substations, one at. either end and 26 miles apart, for supplying the power for the movement of trains of heavy tonnage over the main line and for switching movements at terminal and intermediate yards, and comparatively little feeder copper is required.

Jan 11, 1913

By Samuel Lasky

WITH the movement of American capital into foreign investment, a new field of specialization for the American mining engineer is gradually opening a field hitherto entered almost wholly by chance and without full appreciation of its possibilities. Our age has been fitly called the "Age of Specialization." The special application of one's knowledge and ability to a definite and restricted branch of .his profession is purely a modern condition. Any profession, or branch of a profession or, industry, in which the problems may be segregated into definite types, calls for specializa-tion. Modern industry demands efficiency and that, reduction and ultimate annihilation of waste. Effort and time wasted by workers' on a problem with which they are not familiar is as flagrant a waste of money -the final standard-as any waste of materials. One of the subdivisions of mining engineering which is beginning to be recognized is of engineers who are clearly conversant with the particular and peculiar problems obtaining under foreign operating conditions. The need is as yet obscured, however, by the domestic prosperity of our American mining industry. The opportunity here lies more with the American engineer than with other nationals. The foreign en-gineer now in that service is not there through a realiza-tion of the special opportunities that exist, but through necessity, whereas, with the American engineer, more especially ,the recent graduate or those who will soon graduate, this is a new field to be entered wholly by choice. As a matter of fact, many engineering students will find it necessary to seek foreign service if they wish to remain in mining. Although the scope of the domes-tic industry is tremendous and there are many positions open to the junior engineer, there are not enough for the great number of graduates turned out yearly from our, mining schools. Educators tell us that less than 40 per cent. of the students in engineering schools gradu-ate; and of these but a minority continue in engineering. Even this minority is too great for our domestic. In-dustry, and although the young engineer realizes that condition after a few years he rarely seeks foreign work. A. perusal of the directory of the American Institute of Mining Engineers indicates that, but about one-half of one per cent of the Junior Associates are in positions outside of North America. Granting that most of them are still in school, the figure is surpris-ingly small.

Jan 1, 1927

By D. T. MacRoberts

This paper embodies the results of theoretical studies concerning gas reservoirs, especially the effect of drilling programs of various intensities upon pressure depletion and ultimate recoveries. The primary objective has been to determine the net quantity of recoverable gas that could be obtained as a result of each additional well, in comparison with the gas . that might be secured from a single well ideally placed with respect to both acreage and geological structure. No method is yet known whereby the relative merits of intensive and sparse drilling can be compared experimentally; a reservoir must either be drilled closely or developed with wide spacing, but both programs cannot be conducted simultaneously. Hence, the analytical method seems to be the only approach to the problem. While the present state of our theoretical knowledge does not offer a precise solution to the problem of gas flow in sand bodies, it takes such appropriate cognizance of the limitations of the methods used as to restrict any answer obtained to the realm of engineering accuracy. In solving the problem for the average gas field, it was found that practically the same answers resulted as to pressure distribution, regardless of the size of the drainage radius, even though the latter was assumed to vary from a few feet as a minimum to that of the entire reservoir as a maximum. Such limits represent extreme possibilities; therefore, the practical conditions that are associated with normal development programs, in which wells are placed in the center of tracts varying in size from 40 to 640 acres, will of necessity result in less extreme variations than those indicated in the tables accompanying this paper. Stated more concisely, the amount of gas unrecovered at abandonment (of the particular field used for illustrative purposes) will lie somewhere between 4.6 and 6 per cent of the total original content, no matter how intensively the field is drilled. Gas reservoirs may be divided into two general types, those in which the energy is intrinsic, and those of which the energy is extrinsic. † The first type contains energy in the form of a compressed gas, which expands

Jan 1, 1938

By A. A. Berk

LAGGING technology and the slow spread of information have been the chief obstacles to widespread participation in minimizing the industrial pollution load. These obstacles can be conquered by fact finding and applied research. There are three aspects to the problem of water-borne mineral waste: to minimize the amount being thrown away, to select a predisposal treatment, and to use the products or dispose of them. It is often possible to minimize the waste by making very minor changes in the process that produces it. For example, a manufacturer of automobile bumpers greatly reduced the dragout 'from a plating bath by modifying the design and position of two boltholes.' A plater of automobile hubcaps installed a drainage bar and decreased the loss of chrome-plating solution to the rinse water by about 80 pct.' The mill at a western mine found it possible to discard 60 to 70 pct of an ore with minimum treatment," so that the processing effort could be concentrated on a high-graded slime, with significant reduction in costs and improvement in recovery. The possibilities for waste reduction through process changes are limited only by the imagination. A recent patent points out the advantages of using No. 1 fuel oil instead of water in wet-process cement making;& the fuel oil presumably has better properties than water for this purpose and is said to be almost com'pletely recovered or utilized, so that there is no waterborne waste. Recycling to reduce wastes and improve process economy is very well illustrated in vanadium and uranium recoveries from relatively low grade ore. Ores containing 6 pct calcium carbonate were found to give poor vanadium recovery by the salt-roasting process because the vanadium was converted to water-insoluble calcium vanadate. Following the salt-roasting process, sulfuric acid was used to leach the uranium. Enough calcium sulfate was formed

Jan 1, 1958

By R. V. Wheeler, F. V. Tideswell

Coal being essentially a complex conglomerate of plant remains that have undergone decay and interaction in varying degree, it is understandable that attack on the problem of its chemical constitution by normal chemical methods should have been attended by but slight success. The obvious method of fractionation by means of selective solvents has yielded a few results of some value. Thus it is known that from many, if not all, bituminous coals organic solvents extract small percentages of oxygenated compounds, which are generally assumed to have been derived from the original plant resins, though a more probable source would appear to be the glycerides and waxes of the plants. Organic solvents also extract small proportions of hydrocarbons, the origin of which is doubtfill. Of more importance is the action of such pseudo solvents as pyridine, which, in addition to their specific solvent action, have the power of resolving and simplifying a portion of the coal substance in a manner analogous to that by which water can disperse a hydrogel. Early work with pyridine indicated that coals are composed of two main classes of compounds: the one soluble in organic solvents, the other capable of being partly dispersed in pyridine. Recent work has shown that the dispersion is colloidal in character and that it may be accomplished by the use of solvents less active than pyridine, such as benzene or chloroform, provided that the temperature of extraction is raised or the coal has been suitably preheated. The action of reagents on coal has proved of little value in the past, but some insight into the constitution of coal has been given by regulated destructive distillation. Thus, it has been shown that coals behave on distillation as though composed of two main classes of compounds: the one readily decomposable at moderate temperatures (yielding mainly the paraffins), the other undergoing a preliminary early decomposition (with evolution of oxides of carbon and water) and yielding a residue that at higher temperatures breaks down, yielding much hydrogen.

Jan 1, 1925

By Carl Zapffe

In ten years the manganiferous iron ores of the Cuyuna District have become impor-tant in the iron industry. By Dec. 31, 1923, 4,735,806 tons had been produced. Dur-ing the war, the low-phosphorus black ores were in demand; now the high-phosphorus low,-silica brown ores are favored. It is estimated that the reserves of these ores are ample for some time. A RISE in less than ten years from obscurity into great prominence economically, tersely summarizes the history and status of the Cuyuna manganiferous iron ores. The Cuyuna district produces and ships mostly high-phosphorus iron ore, but the annual production of manganiferous iron ore is increasing rapidly and productions from individual mines are becoming more regular and more dependable as to grades and tonnages. This ore bids fair to become, shortly, the principal product of the district and is responsible for the present economic prominence of this district. The iron ores of the district have been described, by the author and others, in many publications and will not be discussed here. Lately the manganiferous iron ores have been given some attention, but the range and variations of chemical composition of the ores, the principal physical characteristics of the ores and their deposits, the relative importance of the different ores and their possibilities in future developments, and the life of the respective reserves have not been discussed. It is impossible to give all of this information with the positiveness necessary for it to constitute a reliable guide for investment or even for future mine development. Each property and each party presents a special case and deserves critical consideration. We are dealing with special ores and always with a set of new conditions. Sufficient information of a general nature can be given, however, to indicate the reason for and the trend of the presently augmented developments in the district.

Jan 12, 1924

By N. P. Pinto

Compacting below the recrystallization temperature was studied. Ideal density was attained at 550° to 600°C using 25 tsi. Compacts have strength and hardness higher than cold worked beryllium. The recrystallization temperature of this highly stressed metal is that of cast, cold worked beryllium and appears independent of pressing temperature. THE process metallurgy of beryllium is beset by many difficulties that hinder the production of sound beryllium shapes of controlled properties. Most of these obstacles are traceable directly to the low density, low ductility, and high affinity for oxygen of the metal. Castings are susceptible to cracking and porosity, and controlled grain size is not easily attained, yet is critical to further working. Any process must carefully avoid oxygen pickup. Conventional metallurgical processes, including melting, casting, forging, rolling, and extruding have been treated previously,'" as have the conventional powder metallurgical methods.' More recently, a method has been advanced for producing powder compacts of high density by hot pressing at 1000" to 1100°C, using pressures of 0.25 to 0.5 tons per sq in. (tsi).3 Here, Seybolt and coworkers attained theoretical density of 1.85 grams per cc using pres-sure-temperature combinations of 500 psi-1100°C, 750 psi-1075"C, and higher. The warm pressing of beryllium is a practical method for producing bars of controlled properties and appears to have certain advantages, particularly when high strength and hardness are required. Other investigators have studied the hot pressing of various pure metals, such as copper,"-" gold," iron,10-11 and aluminum." Their results indicate that ideal densities may be attained by compacting at temperatures less than 50 pct of the absolute melt-

Jan 1, 1955

By Gerald Sherman

IN the southern field of the anthracite region of Pennsylvania, many of the coal seams dip at angles of 40° to 50° from the horizontal. For transportation purposes, "tunnels" are driven across the coal measures and, occasionally, "rock gangways," beside the seams and parallel with them. The use of gangways driven in country rock appears to be increas-ing, as they avoid the maintenance' of long gangways in coal, which eventually are driven to the colliery boundaries, and permit mining from a number of intermediate blocks without interference. The rock consists of slates or sandstones of moderate hardness, which may range into very hard, highly siliceous, fine-grained conglomerates. In this distinctly bedded formation,' the direction of the heading, whether parallel with or across the structure, makes it necessary to distribute the drill holes in a different pattern to break the ground, but does not change loading conditions. In 1932, practically all the mucking was done by hand, and it was the established custom to use four men on two drills for drilling and breaking the ground, and five for loading it, out. A driver and mule was needed in addition, to assemble the rock cars at a siding or branching track in the rear, pending their final disposal. This might occupy the driver's whole time, or if the length of haul were short, he might be able to do other useful work. It was thought possible in 1932 to reduce the cost of driving such headings in rock by mechanical loading, and to investigate this subject a scraper loader was used in a section of tunnel then being driven. Opera-tions while driving 195 ft. of this tunnel using a scraper loader were care-fully observed. Time studies were made of the loading, and records made of the routine of breaking ground, but not in such detail. Tunnels or gangways in the colliery are 7 ft. high above the rails, by 10 ft. wide, which requires a minimum of 8 ft. in height, broken to allow for rails and ties. This cross section is of sufficient size to permit the use of any one of several types of power loaders, but for this demonstration if was found most convenient to use a scraper loader.

Jan 1, 1936

By Paul H. Price, John P. Nolting

The history of the salt industry in West Virginia dates back nearly two hundred years; howTever, the history of salt as an important raw material for the chemical industry is much more recent. The earliest record of West Virginia salt was in 1753, when a raiding party of Shawnee Indians attacked frontier settlements in Virginia taking captive a number of the pioneers. One of these, who later escaped and returned to her friends, described how the Indians camped at a salt spring on the banks of the Kanawha River and evaporated the water to obtain a supply of salt to take back to Ohio with them. Settlement of the Kanawha Valley began in 1774, that same year the Battle of Point Pleasant ended the Indian's power in the Ohio Valley; and settlement of the Kanawha Valley progressed rapidly with a consequent increase in the importance of the Kanawha Licks as a source of salt. In those days the evaporation of the brine was a family matter for which the family wash-kettle was commandeered. In 1797, Elisha Brooks erected the first salt furnace in the Kanawha Valley. It consisted of two dozen small kettles set in a double row, with a flue beneath, a chimney at one end, and a fire bed at the other. He obtained his brine at a depth of 20 to 30 ft by sinking hollow logs, called "gums" into the salt lick and dipping the brine with a bucket. His production was about 150 lb a day and sold for 8 to 10 cents a pound. In 1806, the Ruffner brothers, David and Joseph, prospected for and drilled the first well in America using a spring pole and steel chisel bit. After several failures they succeeded, in 1808, in drilling to a total depth of 59 ft where they secured a good flow of strong brine. Most standard drilling tools, jars, casing, and practically all the basic oil well drilling machinery now in use, were developed in the drilling of salt wells. To evaporate this brine, the brothers built a wood-burning furnace similar to that of Brooks but with a better arrangement and with more and larger kettles. When production was started they reduced the price of salt to 4 cents a pound. By 1817, there were some 30 salt furnaces in the Kanawha area. It was in this year that bituminous coal first was used as an industrial fuel. David Ruffner again pioneered the way by converting his furnace for the consumption of coal. This year also brought about the formation of the first trust which controlled production and set a price of 1 cent a pound for the salt.

Jan 1, 1950

By R. W. Armstrong, P. C. Jindal

The hardness dependence on grain size for polycrys-talline cartridge brass and a leaded brass has been measured by Brine11 and Rockwell B testing. In each case, the hardness, H, depends on the average grain diameter, 1, according to: H =Ho + kHl-1/2 where Ho and kH are experimental constants. Diamond pyramid hardness values have also been measured as a function of the indentation size and grain size to give additional information on the nature of the hardness test and the dependence of hardness on micro-structure. The hardness of polycrystalline brass depends on its grain size. Bassett and Davis' demonstrated this as early as 1919 by making Brinell hardness measurements on cartridge brass. Since then, the hardness of this type of material has been measured as a function of grain size by making Rockwell,2'3 Vickers,4 and Brinell5 tests. he hardness dependence on grain size has also been measured for other materials. Angus and summers6 investigated the grain size dependence of the Brinell hardness of polycrystalline copper and a Cu-4.5 pct Sn bronze. In other studies, nickel,? Armco iron,Big an Fe-0.07 pct C alloy,I0 and an 0.39 pct C-12.45 pct Cr stainless steel" have been investigated. In some of the preceding cases, the hardness results have been analyzed to show that the hardness varies with the average grain diameter, 1, according to an l-l\4, l-1/4 or I-2 dependence,11-13 The studies of the influence of grain size on hardness have not been based on any theoretical model. This may be because the hardness of a material is itself a complicated property. However, attempts have been made to correlate, experimentally and theoretically, the hardness of a material with its unidirectional stress-strain behavior.14-l6 On this basis, Hall" proposed that the polycrystal hardness dependence on grain size might follow directly from the Hall-Petch18,19 relation for the grain size dependence of the yield stress. Thus, the hardness-grain size relation was given as: H = Ho + kHl-1/2 [1] where Ho and kH were taken as experimental constants. The relation was applied to the measurements on brass,' copper,6 bronze,= and Armco iron.' More recently, this relation was shown by Armstrong and jindal20 to adequately describe the measurements on cartridge brass made by Bassett and Davis' and Babyak and Rhines.5 In this case, the relationship was taken a step further by independently relating the values of Ho and kH to the values of oyand ky, previously reported by Armstrong, Codd, Douthwaite, and petch21 from measurements of the yield stress dependence on grain size for this type of material. In the present investigation, new Brinell and Rockwell B hardness measurements have been made as a function of grain size for a cartridge brass and a leaded brass. In addition, diamond pyramid hardness values were measured as a function of the indentation size. All these results are applied to a further analysis of the hardness dependence on grain size. MATERIALS AND EXPERIMENTAL METHODS Cartridge brass and a leaded brass were selected for this investigation for two main reasons: it was anticipated 1) that these materials could be cold-worked and recrystallized to a wide range in grain size and 2) that the results to be obtained on these typical industrial materials could be usefully compared with previous investigations. The chemical analyses of the actual materials which were employed are given in Table I. The as-received 1/2- and 3/4-in.-thick plates were given various reductions in thickness by cold rolling. The rolled material was heat-treated at various temperatures between 330" and 850°C for differing time periods from 5 min to 9 hr to achieve a variation in the average grain diameter between 0.0339 and 0.000543 cm.22 During heat treatment, the brass was protected from zinc loss by packing it in chips or foils of the same composition material. Reasonably equi-axed grain structures were obtained in each case. The metallurgical grain sizes of the specimens were determined from measurements of the average linear intercept on a random line. Annealing twin interfaces were not counted along with grain boundaries. The

Jan 1, 1970

By S. Arthur Krom

Recent experiments indicate that the usual type of concen-trating-table is not only poorly adapted to produce the desired results, but also is based upon an incorrect principle, namely, the use of riffles to perform the work of stratifying the various minerals. We have heard a good deal about riffles for concentratiug-tables; exhaustive experiments have been made to discover the proper form of riffle, or to prove the superiority of this or that form; disputes and patent-litigation have arisen over the matter of riffles, and thus marly have been led to believe that the riffle is the saving-device upon which the process of concentration depends. In the present paper it is proposed to show that the riffle is greatly overrated as to the part it performs in the concentration of minerals, and that, in the near future, it may possibly be eliminated entirely from that process. The experiments in question have shown that the troublesome riffle can be considered of secondary importance at the most, and should be so classed in the construction of a concen-trating-table built upon the right lines. The action of any form of riffle on a concentrating-table is such as to upset and retard the process of settling and stratifying the various minerals on the table-deck. From the deck of a riffled table no concentrates can be delivered until the deck is " bedded," that is, until a suffcient amount of metallic values has been fed to the table to spread over a large portion of the deck, forming a substratum of the heavier minerals. This substratum must be maintained by the feed within quite narrow limits, and directly proportional to the rate of discharge from the table, in order that the bed shall not be lost. On the other hand, the riffles having a very limited carrying-capacity, considerable care must be taken not to overfeed a riffled table, in which case the table proceeds, in mill parlance, to rob itself. As soon as the space between the

Jan 1, 1912

By Julianne H. Glarmaty, Peter J. Conroy

INTRODUCTION In 1970 the percentage of underground coal extraction by longwall mining methods in the U.S. was 2.1 percent. This figure rose to 4.4 percent in 1976 and is expected to rise to 12 percent by the year 1985. This figure represents 46.0 million tons (51.0 million st) of annual production (Kuti, 1978). In addition, OSM regulations are placing emphasis on subsidence prediction. Section 784.20 of the Office of Surface Mining regulations for underground mining permit applications requires the sutauission of a subsidence control plan which may include monitoring. Because of its nature, longwall mining does not have flexibility in leaving pillars under structures as does room and pillar. Mining in some areas, particularly in the Eastern Coal Field, is approaching more developed areas; therefore, a greater number of structures are expected to be undermined in the near future. Subsidence engineering is becoming an important aspect of mine planning, and should be directed at predicting potential structural damage. The question operators are increasingly faced with is "what will be the subsidence effects for a specific structure at a specific location in respect to a longwall panel?" The most significant variable in assessing the subsidence effect on structures is not vertical subsidence. The variables of strain and tilt are responsible for more structural damage than is the vertical movement. Table I presents threshold values of strain for various structures (Geddes 6 Cooper, 1962). Based on National Coal Board experience, horizontal strain is approximately inversely proportional to the radius of curvature of a circular portion of a subsidence profile; therefore, the radius may be useful in estimating the magnitude of strain caused by subsidence (Hoebs, 1982). The radius of curvature can be determined by the following equation:

Jan 1, 1982

By A. S. Yue

The movphology of the Mg-32 wt pct Al eutectic has been studied as a function of freezing- rate and temperature gradient. At slow freezing rates a lamellar eutectic was formed; whereas, a rod-like eutectic was generated at fast rates. The inter-lamellar spacing increased as the freezing rate decreased in aggreement with theoretical predictions. Lamellar faults, morphologically similar to edge dislocation models in crystals, were responsible for the subgrain structures in the eutectic mixture. A linear increase in fault density with freezing rate was observed. Fault concentl-ations of the order of 10 per sq cm for a range of freezing rates from 0.6 to -3.0 x 10 cm per sec were estimated. The transformation from lamella?, to rod-like morphologies was determined experimentally to be dependent on the freezing rate and independent of the temperature gradient. Moreover, the number of rods formed per- unit cross-sectional area increased exponentiallv with increasing freezing rote. BRADY' and portevin2 classified eutectic structures into lamellar, rod-like, and globular according to the morphology of the solid phases present. Although this classification is quite descriptive, very little has been reported on the details of the mechanism by which the eutectic structures are formed. Recent work by Winegard, Majka, Thall, and chalmers3 and by chalmers4 on lamellar eutectic solidification suggest that the maximum thickness of the lamellae decreases with increasing rate of solidification due to inadequate time for lateral diffusion. scheilS and Tiller' have shown theoretically that the lamellar widths indeed depend on the solidification rate. However, there has been no experimental evidence to support the theory. Chilten and winegard7 have studied the interface morphology of a eutectic alloy of zone-refined lead and tin. They found that the lamellar width decreased as the freezing rate increased in agreement with the theoretical predictions of scheils and Tiller.' More recently, Kraft and Albright' have investigated the microstructures of the A1-CuA12 eutectic as a function of growth variables. They observed lamellar faults present in the lamellar eutectic, similar to edge dislocation models in crystals. Furthermore, Kraft and Albright reported that they could not designate which extra lamellar was responsible for the formation of a lamellar fault even under electron microscopic magnification. In this paper, the morphology of the Mg-A1 eutectic structure is described. The effects of freez- ing rate on the interlamellar spacing and on the lamellar fault density are presented in detail. The transformation from lamellar to rod-like eutectics is discussed in terms of the freezing rate and the temperature gradient. EXPERIMENTAL PROCEDURE The experimental details of alloy preparation, the decanting mechanism and the determinations of the freezing rate and the temperature gradient have been reported elsewhere. Measurements of plate-edge angles were made with a microscope. The true angles used to determine the interlamellar spacings were determined by a two surface analysis technique.'' Since the decanted interface structure does not represent the true eutectic morphology on the solid,g all measurements were made from an area in the solidified bar behind the interface. Measurements of the apparent interlamellar spacings between the two phases of the eutectic were made on a photographic negative by means of a calibrated magnifier. Each value listed in Table I represents the average of thirty measurements on one negative. In general, these measurements are approximately equal with an error of less than pct. The average rod diameter for each specimen was also measured on a magnified photomicrograph. Each value of the diameter represents the average of fifty measurements. RESULTS AND DISCUSSION The experimental observations and their discussion to be presented here are restricted to the morphology of the eutectic structure and to the effects of the freezing rate and the temperature gradient on the solidification of eutectics. INTERLAMELLAR SPACING It has been shown previouslyg that the micro-structure of the decanted interface and the longitudinal section of the Mg-A1 eutectic is characterized by the presence of both lamellar and rod-like morphologies. The lamellae become more regular as the freezing rate is decreased. A three-dimensional photomicrograph representing a perfect lamellar morphology is illustrated in Fig. 1. The lamellae of the top and longitudinal sections of the specimen are regularly spaced while those in the transverse section are not quite straight and parallel. Their parallelism is slightly distorted because fault lines producing a discontinuity are present. A method for calculating the interlamellar spacings A, is described in Appendix 1. The true

Jan 1, 1962

By M. T. Martinson, I. W. Nicholson, C. J. Chindgren, F. P. Williams, L. C. Bauerle, S. F. Ravitz

THE vanadiferous shales of southeastern Idaho and southwestern Wyoming constitute the largest known reserve of vanadium in the United States.1 These deposits have never been exploited except for the relatively small amounts of vanadium recovered by the Anaconda Copper Mining Co. in the treatment of phosphate rock from southeastern Idaho. The major domestic source of vanadium has been the sandstone ores of southeastern Utah and southwestern Colorado. Early in World War II, it appeared that these ores could not meet the greatly increased demand for vanadium, so the investigation described in this report was undertaken to develop processes for the recovery of vanadium from the Idaho-Wyoming deposits. The utilization of these deposits became unnecessary, however, because of greatly expanded production from the Utah-Colorado sandstone ores and the continued availability of vanadium from other sources, chiefly Peru. The major use of vanadium is as an alloying agent in the manufacture of high-quality steels. Vanadium constructional steels usually contain 0.05 to 0.20 pct vanadium, which refines the grain and increases the strength, elastic limit, and resistance to shock and fatigue. Vanadium tool steels not used in high-speed work contain 0.10 to 0.60 pct whereas high-speed tool steels contain 1.0 to 4.0 pct. Vanadium compounds are used as catalysts (principally for the oxidation of SO2 to sulphuric acid and of naphthalene to phthalic acid) and in the paint, chemical, ceramic, dye, and printing industries. The selection of the particular ore deposit to be exploited would involve consideration of many factors besides the metallurgical results that might be obtained. Chief among these would be the reserves of ore available, the grade of the ore, and the mining costs. As very little was known about any of these factors, it was necessary to investigate methods of treatment of all the ores under consideration, working with samples obtained in the course of the exploration work, even though they were not positively representative of the whole deposit from which they were taken. Because of wartime conditions prevailing when this investigation was started, first consideration was given to processes that could be put into operation most quickly and would involve minimum use of strategic materials, even though these processes might not be the most economical.

Jan 1, 1947

By Paul M. Tyler

FULLY a decade ago, demand for ground mica began to exceed supplies of scrap mica from manufacturing operations and of waste block from feldspar and sheet mica mining in the United States, with the result that in recent years the market has absorbed larger and larger quantities of mica recovered as a by-product from clay washing,1 as a joint product with kyanite12 and by grinding schists. So far, only schists that contain a large percentage of mica have been utilized for making ground mica, but already there has been a good deal of wishful thinking with regard to recovering mica as an aid to the prospective working of low-grade gold ores and ores of certain base metals. With wet-ground mica selling at $60 to $100 a ton and even dry-ground mica worth over $20 a ton, many ores that could not be considered as otherwise workable under present conditions will show commercial possibilities if they can be made to yield even a relatively small percentage of salable mica. An interesting paper might be written on the coming role of industrial minerals as joint products of metal mines. It is largely a matter of markets. Many years ago I watched the mess left behind the gold dredges in the mountains of Colorado and thought of the Denver sand and gravel operators who prided themselves upon their canniness in providing devices for catching gold merely as an incident to their regular business of selling what we miners classed as "tailings." Nowadays almost every milling or mining operation near settled communities finds use for at least part of its waste for road material or concrete aggregate and several eastern iron mines have gone into the crushed-stone business. Promoters now mention fertilizer "filler" as potentially salable at all the way from $1 to $10 a ton, or whatever is needed to cover costs of mining and treating the "ore" and leave the metal values as "clear profit." In emulating the pork packers in their efforts to utilize "everything but the squeal,"

Jan 1, 1938

By P. van Meurs

This paper describes a technique which permits visual observation of oil displacement processes througlrout the interior of a porous structure as thick as 2 in. A model having glass walls is filled with finely powdered glass. Such a model becomes completely transparent if the powdered glass pack is saturated with an oil having the same refractive index as the glass. When water or gar, with a refractive index different from that of the oil (glass) is injected, the model becomes opaque in the space occupied by the water (gar). visual observation and photography of these displacement processes are thus rendered possible. The following processes have been studied: (I) displacement of oil by water (linear drive) in a homo-geneous formation and in a stratified formation, (2) water flooding (five-spot well pattern), (3) solution gas-drive process, and (4) oil-bank formation. INTRODUCTION Most of the scaled model experiments heretofore carried out in the Koninklijke/Shell Laboratorium, Amsterdam, have been done in steel containers, in which oil-saturated sand packs represented the oil-bearing formation. In such experiments, for instance those on the displacement of oil by water, the cumulative oil production was measured as a function of the cumulative water injection. In order to interpret the measured production data, a need has for some time been felt for a means of observing visually what happens in the course of such experiments. Some information of this kind was obtained earlier by observing the water-oil distribution in various cross sections of the sand after the conclusion of the experiment.' However, the technique used did not guarantee that the fluid distribution remained undisturbed. Moreover, the procedure was somewhat elaborate and the information obtained limited. Therefore a new technique has been developed, which is described below. DESCRIPTION OF EXPERIMENTAL TECHNIQUE AND APPARATUS Glass models simulating part of an oil reservoir are filled with ground Pyrex glass of a specific grain size, representing the porous structure of the prototype. Before an experiment is started, the porous formation has to be saturated completely with an oil having exactly the same refractive index as the Pyrex glass powder. All light-scattering surfaces of the glass grains become invisible and the formation is then transparent. If the oil is displaced by another fluid (e.g. by water in a water-drive experiment, or by gas liberated from the oil in a solution gas-drive experiment) the formation becomes opaque in the region where the oil is expelled from the rock.* The back of the apparatus is painted black and illumination is from the front; therefore, in the photographs of the experiments, the oil-bearing formation appears black, whereas the water- or gas-invaded areas are white.

Jan 1, 1958

By J. N. Breston, R. V. Hughes

Conclusions drawn by previous research workers with reSPect to the relation between Pressure gradients and/or velocity and oil recovery obtained by laboratory water flood tests have been in disagreement probably due to variable procedures and unnatural conditions and materials. The Bradford Laboratory of the Pennsylvania Grade Crude Oil Association as part of its secondary recovery research program has conducted nineteen water floods on two long cores of widely differing characteristics in an attempt to clarify this relationship and make it an aid in predicting flooding pressures in the field. Unlike previous research procedures the present experiments were conducted with the aim of duplicating field conditions as closely as possible by using long unextracted consolidated cores, a live crude, and natural brines for both flooding and, connate water content. Also, the pressure gradients and flooding velocities were representative of field conditions where similar sands were being flooded. Eleven floods on one core and eight floods on the other core showed increased recoveries and lower residual oil saturation with increased flood pressure gradients and flood velocities. A marked decrease in recovery was obtained from both cores at very low flood velocities. This pressure versus recovery relationship is shown to hold up to the point of water breakthrough and also up to the 100 and 1 produced water to oil ratio point. INTRODUCTION The possibility of water flooding oil sands was suggested by Carl1 of the Pennsylvania Geological Survey in 1880. It is not known when the practice was tried intentionally for the first time, but its beneficial effects were noted in the annual production rate of the Bradford field as early as 1907. The practice was illegal in Pennsylvania until 1921. Early water floods in the Bradford field usually consisted of shooting or splitting the casing secretly to permit subsurface waters to enter the producing sands under hydrostatic head. As it was noted that the benefits of water flooding seemed to be proportional to the quantity of water dumped into the well many also began to utilize surface sources after the practice became legal. It was probably during the middle 20's before many producers realized that the pressurehead of the water upon the producing sand determined the rate and quantity of water that would enter the sand. Hence, rate and quantity of production appeared to be a direct function of input pressures. By 1927 a few producers had ventured the installation of pressure pumps in order to increase water-input rates and production through the combination of hydrostatic and hydraulic pressures. The adoption of pressure flooding and the "five-spot" drilling pattern in the Bradford field were essentially simultaneous. Water-input pressures in 1930 seldom exceeded 300 p.s.i. at the well head or 1100 p.s.i. at the sand face. Since that time, water-flood producers in the Bradford-Allegany fields have gone to higher and higher pressure until today 600 p.s.i. at the well heads is called a low pressure flood. Many high pressure floods now operate at 1300-1400 p.s.i. at the well head. The limiting and advisable pressure at the sand face has been pronounced as that pressure just under what is required to lift the overburden or to cause formation parting: According to this rule any water flood operation utilizing well-head pressures nearly equal in pounds per sq. in. to 1.1 times the average depth in feet to the top of the producing sand would be considered as a high-pressure flood. Despite the higher pressure trends in the Bradford-Allegany field operations and the results of early laboratory water flooding research, the desirability and benefits of high input pressures are still questioned by many operators, particularly in midwestern water flood operations. The present paper recounts a series of 19 laboratory water floods using two long, consolidated cores of widely differing characteristics saturated with live crude and flooded with oil field brines in an effort to simulate field conditions under • various pressure gradients and flooding velocities. For both cores, higher recoveries and lower residual oil saturations were obtained at higher pressure gradients and flood velocities. This relationship is shown to hold up to the water breakthrough point and also up to the 100 to 1 produced water to oil ratio point.

Jan 1, 1949

By R. V. Hughes, J. N. Breston

Conclusions drawn by previous research workers with reSPect to the relation between Pressure gradients and/or velocity and oil recovery obtained by laboratory water flood tests have been in disagreement probably due to variable procedures and unnatural conditions and materials. The Bradford Laboratory of the Pennsylvania Grade Crude Oil Association as part of its secondary recovery research program has conducted nineteen water floods on two long cores of widely differing characteristics in an attempt to clarify this relationship and make it an aid in predicting flooding pressures in the field. Unlike previous research procedures the present experiments were conducted with the aim of duplicating field conditions as closely as possible by using long unextracted consolidated cores, a live crude, and natural brines for both flooding and, connate water content. Also, the pressure gradients and flooding velocities were representative of field conditions where similar sands were being flooded. Eleven floods on one core and eight floods on the other core showed increased recoveries and lower residual oil saturation with increased flood pressure gradients and flood velocities. A marked decrease in recovery was obtained from both cores at very low flood velocities. This pressure versus recovery relationship is shown to hold up to the point of water breakthrough and also up to the 100 and 1 produced water to oil ratio point. INTRODUCTION The possibility of water flooding oil sands was suggested by Carl1 of the Pennsylvania Geological Survey in 1880. It is not known when the practice was tried intentionally for the first time, but its beneficial effects were noted in the annual production rate of the Bradford field as early as 1907. The practice was illegal in Pennsylvania until 1921. Early water floods in the Bradford field usually consisted of shooting or splitting the casing secretly to permit subsurface waters to enter the producing sands under hydrostatic head. As it was noted that the benefits of water flooding seemed to be proportional to the quantity of water dumped into the well many also began to utilize surface sources after the practice became legal. It was probably during the middle 20's before many producers realized that the pressurehead of the water upon the producing sand determined the rate and quantity of water that would enter the sand. Hence, rate and quantity of production appeared to be a direct function of input pressures. By 1927 a few producers had ventured the installation of pressure pumps in order to increase water-input rates and production through the combination of hydrostatic and hydraulic pressures. The adoption of pressure flooding and the "five-spot" drilling pattern in the Bradford field were essentially simultaneous. Water-input pressures in 1930 seldom exceeded 300 p.s.i. at the well head or 1100 p.s.i. at the sand face. Since that time, water-flood producers in the Bradford-Allegany fields have gone to higher and higher pressure until today 600 p.s.i. at the well heads is called a low pressure flood. Many high pressure floods now operate at 1300-1400 p.s.i. at the well head. The limiting and advisable pressure at the sand face has been pronounced as that pressure just under what is required to lift the overburden or to cause formation parting: According to this rule any water flood operation utilizing well-head pressures nearly equal in pounds per sq. in. to 1.1 times the average depth in feet to the top of the producing sand would be considered as a high-pressure flood. Despite the higher pressure trends in the Bradford-Allegany field operations and the results of early laboratory water flooding research, the desirability and benefits of high input pressures are still questioned by many operators, particularly in midwestern water flood operations. The present paper recounts a series of 19 laboratory water floods using two long, consolidated cores of widely differing characteristics saturated with live crude and flooded with oil field brines in an effort to simulate field conditions under • various pressure gradients and flooding velocities. For both cores, higher recoveries and lower residual oil saturations were obtained at higher pressure gradients and flood velocities. This relationship is shown to hold up to the water breakthrough point and also up to the 100 to 1 produced water to oil ratio point.

Jan 1, 1949