Search Documents

By R. W. Hertzberg, F. D. Lemkey, J. A. Ford

The effect oj unidirectional solidification upon the microstructural, crystallographic and mechanical characteristics of high -purity A1-A13Ni eutectic a1loy specimens has been investigated. varying the growth rate caused the morphology of the Al3Ni phase to gradually change from platelets to rods. In addition, the effect of increasing the rate of planar liquid-solid interlace movement is to decrease the Al3Ni rod diameter and inter-rod spacing. The platelets and rods grow approxinlately parallel to each other and are aligned in a faulted substructure. A single unique crystallographic relationship hetween the A1 and ASNi phases was found and may he descrihed as : interface {001} Al3Ni {331} Al and growth direction <010>Al3Ni || <110> Al The platelet interlace and the aligned rows of rods are both uniquely defined by the above statements. Alignment of the Al3Ni phase by unidirectional solidification has given rise to a threefold increase in strength over that exhibited by specimens with an as-cast microstructure. These results illustrate the possible use of this eutectic alloy as a zohisker -reinforced structure. It has been demonstrated by Winegard et al.,1 Kraft and Albrighht,2 Chilton and winegard,3 Chad-wick,4 Yue,5 Tiller,6 and others that a planar liquid-solid interface may be established in binary eutectic alloys by proper control of heat flow during the solidification process. The unidirectional movement of such an interface results in a eutectic mi-crostructure consisting of an essentially parallel array of the two phases over an entire ingot. Two dominant phase micromorphologies have been produced using this technique: that of substantially parallel alternating lamellae of each phase or long thin parallel rods of one phase imbedded in a continuous matrix of the other phase. While not all eutectics can be controlled in this manner, it has been shown that a "normal" eutectic may, under properly controlled conditions of purity, liquid and solid thermal gradients, and solidification rate, be forced to solidify with essentially parallel phase particles. Kraft and Albright2 have demonstrated that, when the growth rate is too rapid or when the thermal gradient in the liquid at the growing interface is too low, a layer of constitutionally supercooled liquid, formed by impurity build-up, will stabilize a cellular rather than a planar interface. The unidirectional movement of the cellular interface forms the macrostructure of eutectic colonies.7 Chilton,3 Chadwick,4 and Tiller,&apos; studying eutectics of zone-refined Pb-Sn, A1-CuAl2, Zn-Sn, and Cd-Zn systems, noted that in the absence of impurities a planar interface is stabilized even when rapidly solidified. Although it is generally agreed that impurities break down a planar interface to form the eutectic-colony macrostructure, at present the origin of the varying micromorphologies (i.c., plates or rods) in a given normal eutectic alloy is not completely understood. Tiller8 has predicted that the micromor-phology produced may be dependent on solidification rate (i.e., at fast rates a rodlike structure is preferred whereas at slow rates a lamellar structure should form), and also suggested that rod formation may be favored at large phase-volume ratios. yue5 has experimentally verified Tiller&apos;s prediction in the eutectic Mg-Mg17Al12 by observing a lamellae-to-rod transition with increasing growth rate where the phase-volume ratio was approximately 2.3:1. However, Hunt and chilton9 more recently unidirec-tionally solidified over a wide range of growth velocities six different eutectic systems with phase-volume ratios between 12:l and 2.7:1 and observed no lamellae-to-rod transition. chadwickl0 has proposed that the change in micromorphology in some eutectic alloys is due entirely to the presence of impurities and further states that the lamellar structure is the characteristic structure of pure eutectic alloys even when the phase-volume ratio is as great as 12:l. Kraft11,12 has shown that the parallel lamellae in certain eutectic alloys assume a unique crystallographic relationship during unidirectional growth. This preferred crystallography may be developed

Jan 1, 1965

By Robert Henderson

Several very interesting articles have been written on the caving system of mining, but most of these papers have dealt separately with the slusher system or the chute and grizzly system. In this paper, a comparison will be made of the two methods, both of which are being used at the Climax mine. The mine is on the Continental Divide, in central Colorado, at an altitude of approximately 11,500 ft. above sea level. The long, cold winters, characteristic of the high Rockies, create a number of operating problems not usually found in other mining areas. The Ore Body The Climax ore body is just east of the Mosquito fault. This structural deformation has brought the granite on the east against the sedimentary rocks on the west. The ore occurs in an intensely altered granite and schist around a silicified granite core. The ore is in a highly fractured zone of moderate silicification. The principal mineral, molybdenite, is found in these fractures. Barren dikes of granite porphyry cut through the ore body and core with no apparent regularity. The grade of the ore is fairly uniform and gradually decreases toward the footwall core and also into the hanging-wall granite. The footwall and hanging wall are determined entirely by assays. The ore body is roughly dome-shaped, with the apex truncated at the surface. It is covered to varying depths with talus. A horizontal section of the ore body on the Phillipson level appears as an annular ellipse surrounding the footwall core. The ring of ore varies in width from 300 ft. to as much as 800 ft. The north-south axis of the core is about 1200 ft. and the east-west axis is about 1800 ft. In the ore zone, the rock is sufficiently strong to maintain reasonably large openings, and openings larger than haulage drifts usually have to be supported. The ore is cut by a great many fractures and shears and breaks into rather large blocks when caved, necessitating considerable secondary blasting. The waste that overlies the ore body breaks relatively fine in comparison with the size of the blocks of the caved ore and tends to run through the broken ore in the cave, causing dilution unless the draw is carefully controlled. Mining Systems For several years the ore was mined by the chute and grizzly system, a system that differs from that used in other caving mines only in the size of openings and equipment. In the chute and grizzly system, main haulage laterals were driven along the footwall core and also along the hanging wall. Between these laterals, at

Jan 1, 1946

By L. L. Newman

As soon as the Congress recognized the alarming rate at which our domestic oil resources were being depleted during the war, it took action to step up the rate of research and development which the Bureau of Mines had been conducting for several years on the production of synthetic liquid fuels from coals. Under Public Law 290, approved April 5, 1944, funds were authorized for the Bureau to proceed with research, development, design and construction of demonstration plants for the hydrogenation of coal, the synthesis of oil from carbon monoxide and hydrogen, and the distillation of oil from shale. During the latter part of 1944, when it became evident that the collapse of Germany was near, a Technical Oil Mission was organized to study the German techniques of synthetic oil production. Since the cost of hydrogen or synthesis gas is one of the major factors of expense in the operation of hydrogenation or synthesis gas processes, the Bureau of Mines considered it of prime importance to include on the mission gas engineers whose instructions were to examine closely the methods employed by the Germans in solving the problem of providing low-cost hydrogen or synthesis gas for their very extensive operations on synthetic liquid fuels. The Solid Fuels Mission and the Utilities Mission, as well as the Army and Navy Missions, also included teams for the study of German gas production. Although their objectives naturally differed from those of the Technical Oil Mission and from each other, it was recognized that there was considerable overlapping of their fields of investigation. Duplication of effort, however, was largely avoided through the close cooperation between the group leaders of these missions. For example, although I went to Europe as a member of the Technical Oil Mission, my first Gcrman assignment was actually made by Dr. Harry F. Yancey, leader of the Solid Fuels Mission— to investigate the brown-coal gasification methods in central Germany. The art of gasification in the United States and England, and to a large extent in the proximity of the coking-coal regions of Germany and the rest of continental Europe, depends essentially on two stages of operation; namely, carbonization and intermittent water-gas generation. As far as the United States is concerned, complete gasification in a single stage of operation is rarely practiced, except in gas-producer operations where the product is a relatively lean gas consumed close to the point of manufacture, and for water-gas production with anthracite as a generator fuel. Complete gasification of bituminous coal has been the subject of numerous investigations. Many relatively simple modifications of the water-gas generator have been tried to permit the direct gasification of low-cost bituminous coal instead of high-cost coke and anthracite for the production of water gas. Although varying degrees of Success have been achieved and the water gas produced generally has been higher in

Jan 1, 1947

By L. L. Newman

As soon as the Congress recognized the alarming rate at which our domestic oil resources were being depleted during the war, it took action to step up the rate of research and development which the Bureau of Mines had been conducting for several years on the production of synthetic liquid fuels from coals. Under Public Law 290, approved April 5, 1944, funds were authorized for the Bureau to proceed with research, development, design and construction of demonstration plants for the hydrogenation of coal, the synthesis of oil from carbon monoxide and hydrogen, and the distillation of oil from shale. During the latter part of 1944, when it became evident that the collapse of Germany was near, a Technical Oil Mission was organized to study the German techniques of synthetic oil production. Since the cost of hydrogen or synthesis gas is one of the major factors of expense in the operation of hydrogenation or synthesis gas processes, the Bureau of Mines considered it of prime importance to include on the mission gas engineers whose instructions were to examine closely the methods employed by the Germans in solving the problem of providing low-cost hydrogen or synthesis gas for their very extensive operations on synthetic liquid fuels. The Solid Fuels Mission and the Utilities Mission, as well as the Army and Navy Missions, also included teams for the study of German gas production. Although their objectives naturally differed from those of the Technical Oil Mission and from each other, it was recognized that there was considerable overlapping of their fields of investigation. Duplication of effort, however, was largely avoided through the close cooperation between the group leaders of these missions. For example, although I went to Europe as a member of the Technical Oil Mission, my first Gcrman assignment was actually made by Dr. Harry F. Yancey, leader of the Solid Fuels Mission— to investigate the brown-coal gasification methods in central Germany. The art of gasification in the United States and England, and to a large extent in the proximity of the coking-coal regions of Germany and the rest of continental Europe, depends essentially on two stages of operation; namely, carbonization and intermittent water-gas generation. As far as the United States is concerned, complete gasification in a single stage of operation is rarely practiced, except in gas-producer operations where the product is a relatively lean gas consumed close to the point of manufacture, and for water-gas production with anthracite as a generator fuel. Complete gasification of bituminous coal has been the subject of numerous investigations. Many relatively simple modifications of the water-gas generator have been tried to permit the direct gasification of low-cost bituminous coal instead of high-cost coke and anthracite for the production of water gas. Although varying degrees of Success have been achieved and the water gas produced generally has been higher in

Jan 1, 1947

By William Marsh Baldwin

[Two of the most useful and important equations available to the metallurgist for the study of plastic deformation of metals are the Huber-von Mises-Hencky1-3 and the St. Venant7-10 equations. HUBER-VON MISES-HENCKY EQUATION The Huber-von Mises-Hencky equation answers the question: When does plastic flow occur in metal that is subjected to a multi-axial stress? It occurs, according to this equation, when the three principal stresses,? al, a2, and a3 satisfy the equation: (s1 - s2)2 + (s 2 - s 3)2 + (s 1 ? s3)2 = 2K2 [I] Here K is the yield strength of the material as determined in an ordinary tensile test. If the quantities a1, a2, and a3 are assigned to the coordinates of a Cartesian three-dimensional system, this expression describes a cylinder whose axis of symmetry is inclined at equal angles to the three coordinate axes4,5 (Fig. I). The radius of this cylinder is v2/3K. For the purpose of simplicity, it is sometimes advantageous to ascribe the values s 1/K = si, s 2/K = s2, s 2/K = s3 to the three coordinate axes instead of the principal stress alone. In this case, Eq. I becomes (s1 - S2)2 + (S2 - S3)2 + (Sl - S3)2 = 2 [2] and the radius of the cylinder becomes 2/3v. In the latter method of representation, a point lying inside the cylinder indicates that the metal will react elastically, whereas a point lying on the cylindrical surface indicates that the metal will behave plastically. Some of the geometric features of this cylinder are worthy of study. Let us inquire first as to what interpretation may be placed upon what we will choose to call the "circles of latitude" of the cylinder (L in Fig. I) and the "meridians" of the cylinder (M in Fig. I). Circles of Latitude Circles of latitude are formed by allowing a plane, passing perpendicular to the cylinder axis, to intersect with the cylinder. Any point, P, on this circle is presumed to have the coordinates s1, s2, and s3. The coordinates of the point resulting from the intersection of the plane and the cylinder axis will be a, a, and a (since the cylinder axis is equally inclined to the three coordi¬nate axes). Let us now pass a line through the point on the circle and the point on the axis.]

Jan 1, 1946

By S. P. Kinney, A. J. Boynton

THIS paper is not the result of recent research with regard to any particular feature of iron metallurgy, blast-furnace practice or mechanical engineering. It is rather a series of notes with regard to contemporaneous progress in blast-furnace construction and operation, together with some suggestions as to changes and improvements that seem to be desirable. On April 1, 1930, a committee of the Chicago District Blast Furnace and Coke Association presented to that association a rather ambitious study of blast-furnace equipment, together with recommendations for the design of construction of a complete blast-furnace unit for the production of 1000 tons of pig iron per day. This report represented the result of months of study by members of the committee, all of whom were actively engaged in operation or design of blast-furnace plants. It is natural, therefore, that comments on the present state of the art should take this 1000-tons furnace, as recommended by the Association, as a basis for comparison with corresponding features of construction or design. See Table 1. In looking through this report at the present time, the significant difference is in the nature of the gas-washing equipment that today would be specified. In other respects, the installation would remain generally very much as it was outlined in 1930. The change in furnace dimensions would be very slight and of no especial significance, except with respect to changes in stock-line diameter, of which more will be said hereafter. The high-efficiency stove as developed by various designers is thoroughly described within this report, and few changes have taken place since. Blowing equipment shows refinement and reflects the improvement in steam engineering. Hoisting and charging equipment and ladles for the conveyance of iron and slag remain, in general, as they were in 1930. In accordance with a general tendency

Jan 1, 1935

By D. F. Kaufman, E. D. Levine, L. R. Aronin

The deformation of&apos; impure beryllium crystals by basal glide at room temperature invariably tevminates by basal cleavage after a few percent strain. It is generally accepted that .fracture of this type is caused by the splitting of low) -angle boundaries, or bend planes, by obstacles that restrict the motion of the bed planes in the deforming crystal. The details of such a process have been developed by Stroh, who showed that the high tensile stress norrnal to the basal plane in the region where the bend plane is split results in the propagation of a basal cleavage crack, provided there is no available dejorvrlatzon mode having a shear component normal to the basal plane It has been postulated that puvification of beryllium might lead to increased basal ductility by the vemoval of barviers to bend plane motion and possibly by the activation of nonbasal defor~rlation systems. Large increases in the amount of basal glide that can he sustained prior to fracture have been observed in crystals purified by zone refining. In each case, eventudal fracture was by sharp basal cleavage, suggesting that the split bend plane model still applies to tile fracture of beryllium of rensonably high purity. In the present work, calculations are made to show to what extent basal duetilits can be increased by purification while the split bend plane .fracture process remains applicable. Experimentally observed ductilities are generally somewhat lower than those predicted by calculation because of premature failure due to defects introd~cced during specimen preparation and testing. SEVERAL investigators1-4 have studied the deformation characteristics of beryllium single crystals of commercial purity, and have related the strong anisotropy of plastic deformation in single crystals to the problem of brittleness in polycrystalline beryllium. For most orientations, the principal deformation mode is basal slip, which, at temperatures between 300" and 900°K, begins at a critical resolved shear stress of approximately 1500 g per sq mm and terminates after 3 to 6 pet glide strain by cleavage on the basal plane in the neighborhood of (1120) bend planes that are formed during the deformation. This type of fracture, which is also observed in zinc at low temperatures, has been interpreted by stroh5 to be caused by the splitting of bend planes by obstacles to their motion. In the Stroh model, a (11.20) dislocation wall, or bend plane, moving along the slip direction under the action of the applied stress, encounters obstacles which cause part of the bend plane to be held up, the other part continuing to move. Stress concentrations are built up in the region where the bend plane is split, with a high tensile component normal to the basal plane, resulting in a microcrack at the end of the split wall. Because no deformation mode having a shear component at an angle to the basal plane is available to relieve the stress at the crack tip, the crack can propagate under a sufficiently high applied stress. The Stroh criterion for crack propagation is given by

Jan 1, 1964

By T. M. Geffen, R. E. Gladfelter

Lipson1 has recently presented a technical note wherein theoretical considerations were used to demonstrate. that the adsorption us saturation relation for a linear absorption method is not necessarily a single valued function of saturation.1 It was concluded that the absorption us saturation relationship is subject to the same hysteretic effect as is the flow behavior between the drainage and imbibition systems. It is the purpose of this note to show, by experimental results, that for the manner in which fluids are distributed in porous materials during fluid flow, the relative X-ray absorption us saturation relationship is single-valued regardless of the saturation history. The design of the apparatus used to measure relative X-ray absorption of cores undergoing fluid flow tests is similar to that described by Morgan, McDowell and Doty. A few modifications have been incorporated in the design to increase sensitivity and simplicity of measurement. The sensitivity is such that for usual types of cores a recording pen movement of approximately 12 linear in. is occasioned between the recording of the core dry and when it is completely full of an absorbing liquid, a solution of approximately five per cent by volume of iodo-benzene in a close-cut hydrocarbon fraction, or a solution of 50,000 ppm sodium iodide in water. Two types of experiments were conducted, one in which the liquid was inside the core, and the other with the liquid outside the core. Tests with the liquid inside the core were run to cover the saturation range encountered in both the drainage (gas drive) and imbibition (liquid flood) flow systems. It is pointed out that the same core was used, but the tests were conducted at different times with the recording mechanism balanced at a different position. Therefore, the absolute values of relative X-ray intensity at any saturation are not the same in each test. In the second type of test the same core was used, but this time its pore space cmtained only gas, and various thicknesses of oil contained in plastic cells were placed in front of the dry core. As before. the relative X-ray ah- sorption was measured and compared to the quantity of oil in front of the core. The arrangement of the fluids with respect to the path of X-rays in these two types of tests represent fluid distributions of a wider difference than can be expected between that established in a core just due to imbibition and drainage saturation flow histories. Thus any deviation from a straight line relationship of the log of the relative X-ray intensity us saturation calibration should be readily apparent. Results of the laboratory tests are given in Fig. 1. A schematic diagram showing the position of the fluids with respect to the path of the X-ray beam is given for the two cases investigated. In the case where the oil existed outside the core (Case B), the log of the X-ray intensity (log, I/I,) is related directly to the cell thickness (amount of oil in X-ray beam path). This correlation is in full agreement with X-ray theory. In the case where the oil or water existed inside the core (Case A) which covers both drainage and imbibition types of flow processes, again the relationship between absorption and saturation (amount of oil in X-ray beam path

Jan 1, 1952

By Thomas Leonard Watson

I. Historical. Barite has been mined for many years in various parts of Virginia, probably the earliest mining-operations being in Prince William county, within 600 ft. of the Fauquier county line, about 4 miles south of east from Catlett, a station on the Southern Railway. It is claimed that the mineral was mined here as early as 1845. Mining-operations in Campbell and Pittsylvania counties in the Piedmont region, and near Marion in Smyth county, in the southwest Virginia Valley region, were begun about 30 years ago. The mining and milling of barite on a commercial scale in Tazewell and Russell counties are more recent, and commenced about 15 years ago. II. Geographical and Geological Distribution. Barite occurs in many counties in the State, as shown in Fig. 1, but the industry has been confined to only a few of them. Its occurrence is noted in two of the three major divisions of the State—namely, the Piedmont region east of the Blue Ridge, and the Paleozoic area west of the Blue Ridge. In the Piedmont region the mineral has been mined in the following counties: Bedford, Campbell, Louisa, Prince William, and Pittsylvania. In the region west of the Blue Ridge, composed of Paleozoic sediments, barite has been mined in Montgomery, Russell, Smyth, and Tazewell counties. Of the counties mentioned, Bedford, Campbell, and Pittsylvania of the Piedmont region, and Russell, Smyth, and Tazewell of the Valley region, have been the principal producers. In 1906, operations were confined to five counties—Bedford, Louisa, Pittsylvania, Russell, and Tazewell—but in the first two counties named there was no production, the work being solely development.

Jan 1, 1908

By R. M. Goldhoff, J. W. Spretnak

IN connection with establishing the mechanism by which boron enhances the hardenability of heat treatable steels, this research work has been undertaken. Spretnak and Speiser1,2 indicated the need for studying high temperature effects in boron steels and, chief among these, the possible nonhomogeneous distribution of boron in iron grains. The occurrence of this effect may be of significance in explaining the mechanism of enhancement of hardenability by boron as well as in explaining some of the observed characteristics of boron steel behavior. Primarily, then, this work was undertaken a) to establish whether or not boron is adsorbed in ? solid solutions, b) to determine the nature of any such adsorption effects, i.e., whether it is positive or negative as well as its temperature coefficient, and c) to establish the magnitude of any such effect. While past literature on this specific subject is rather sparse, a number of authors have postulated that the observed temporary loss of hardenability as well as the occurrence of the characteristic boron constituent in these steels is due to the nonuniform distribution of boron in austenite.3-0 Experimental Techniques Attempts to obtain direct evidence of grain boundary effects in boron steels have been unsuccessful, both by using the technique of Chalmers&apos; in which small concentrations of solute made radioactive by irradiation are detected by autoradiographic means, and by means of studying cleavage fractures with the electron microscope.8 The present study attempts the design of experiments to measure the effect of boron on properties which might be subject to variation because of grain boundary effects. A study of the theoretical aspects of grain growth indicates that such studies may be pertinent. Another valid type of experiment involves the measurement in polycrystalline materials of properties whose values depend on the bulk of the grain, being negligibly influenced by grain boundaries. One such property is the lattice parameter measured by X-ray diffraction. The value of the lattice parameter reflects the average conditions which obtain over a relatively large number of atoms in a fixed crystalline lattice, and is therefore mainly dependent on bulk grain material. Measurement of lattice parameter variation over the austenite range of temperature in iron with and without boron should give evidence of concentration variations in the bulk grain material if adsorption effects are significant. Finally, use is made of the Grange and Garvey3 metallographic test for boron in which a characteristic boron constituent can be developed in austenite grain boundaries. The very occurrence of this phenomenon suggests grain boundary enrichment of boron and a study of the occurrence of this constituent and its varation with austenitizing temperature should help to detect grain boundary effects. Materials One lb ingots of pure iron, an Fe-B alloy, an Fe-C alloy, and an Fe-C-B alloy were prepared. The melting technique included an initial melting of electrolytic iron under vacuum followed by remelting under hydrogen and, finally, by melting under argon with the addition of alloying elements. Each ingot was surface machined between meltings. A quantitative spectrographic analysis was obtained on the pure ingot and, in addition, oxygen, nitrogen, and carbon were determined by the vacuum fusion method. The results of these analyses are given in Table I. Semiquantitative spectrographic analyses were performed on the alloy ingots, while quantitative determinations of the alloy additions were obtained. These analyses are shown in Table 11. The cast ingots were subjected to the following sequence of fabrication treatments: forging to 5/8 in. bars, swaging to 0.300 in. rounds, drawing to 0.025 and 0.010 in. wire. Portions of each ingot were retained in the swaged condition for experimental use. For certain portions of the work typical commercial steels were used. These materials were supplied by the Republic Steel Corp., Canton, Ohio, and correspond to AISI 8640 and AISI 86B40 compositions.

Jan 1, 1958

By R. Laird Auchmuty

The A. I. M. E. Subcommittee on Bituminous Mining has been trying for several years to secure the information that was collected by the Marquette Cement Manufacturing &. on the subsidence of its property caused by mining coal beneath it. The Marquette company was willing to have these data used, but it was impossible to obtain them because the records had been filed away. About two years ago these records became available and the engineering data presented herewith were compiled from them by R. L. Auchmuty, assisted by L. E. Young, who was connected with the collection of the information. On account of the cost, it is impossible to reproduce all of the data here, although the original information is on file with the records of the Committee on Ground Movement and Subsidence. The accompanying charts show representative and average data and give only the engineering information with enough description to tell how it was obtained. It is hoped that all of those connected with the original case will participate in the discussion that this will bring forth. Howard N. Eavenson, Chairman, Subcommittee on Bituminous Coal Mining. PRobably the most complete records of subsidence due to coal mining in the United States are those compiled by the Marquette Cement Manufacturing Co. at LaSalle, 111. These records, covering a period of more than three years, were compiled and used as evidence during the suit of the Marquette Cement Manufacturing Co. vs. the Oglesby Coal Co. at Oglesby, LaSalle County, Ill., in which the cement company successfully endeavored to stop the coal company from mining under its property. Fig. 1 shows a typical section of the geological formation. The cement company was mining the LaSalle limestone which lies about 125 ft. under the surface. The limestone is 30 to 35 ft. thick and underlain by about 15 ft. of shale. The cement company was mining about 20 ft. of the limestone, and in some places 10 to 12 ft. of the underlying shale, by the room and pillar method. The mining of the limestone always preceded the mining of the shale. The coal company was mining by longwall advance methods the NO. 2 seam of coal 42 in. thick underlying the limestone bed by 435 to 470 ft. The coal mine, a very old one, had largely mined out its original property

Jan 1, 1931

By Louis S. Cates

At the annual meeting of the American Institute of Mining and Metallurgical Engineers in February, 1923, the Chairman of the Committee on Ground Movement and Subsidence appointed a sub-committee to work out a form of questionnaire and to collect data on subsidence and ground movement resulting from underground metal and coal-mining operations, and on ground movement and safe slopes in connection with open-cut metal-mining operations. The author was requested to take charge of the collection of data and the preparation of a questionnaire in connection with the Committee&apos;s studies of open-cut metal-mining operations. This paper is a summary of the work carried on and information received therefrom up to February, 1924. The first approach to the problem of safe slopes is to gather all information that pertains to finished slopes; in other words, the steepest economic angle from the horizontal that will stand in order to uncover the ores to be mined and be safe while the extraction of the ore at the base of these slopes is in progress. Whether or not this angle is 35" or 45" depends on many factors. The number of benches maintained to take care of falling rock and their height and width are direct functions of this overall slope. The slope is here taken to mean the angle from the top edge of the pit through the edges of the respective lower benches to the bottom of the pit. If we accept this definition of the slope, it might save some confusion as there would be a difference if one took the line from the top edge of excavation to the toe of the bottom slope. This latter slope would not be constant, but would vary with the number of benches. The depth of the various ore faces will vary, of course, depending on the deposit; Table 1 shows this to range from 50 ft. to 1100 ft. The geology is an important factor, as are the climatic conditions under which one is operating. A saturated condition in some rock structure causes rock flows; in the Panama Canal excavation, slides have run on a ratio of as low as one on ten, which is a 10 per cent. grade, or a slope of less than 6&apos; with the horizontal. Slopes as steep as 60&apos; have been noted in the Utah Copper operations, so that a wide divergence will possibly be met. The work of securing data that will be of value to the operator or estimating engineer will be difficult and will mean little unless a detailed

Jan 1, 1927

By Wallace W. Wilson

The Cook Ranch Field produces from a very permeable lens of Cook Sand of lower Permian or upper Pennsylvanian age, occurring at an average depth of 1.300 ft. The field was discovered in 1926, and has been operated with low pressure gas injection since July, 1927, one of the first such projects in Texas. Cumulative recovery to Dec. 31. 1950, was 14,701,131 bbl of crude oil, an average of 1,013 bbl per acre-ft of oil rection. and 72.5 per cent of the oil originally in place. Analysis of the reservoir performance indicates that grav-ity drainage has been an important factor in the producing mechanism. The high permeability and uniformity of the reservoir were extremely Favorable tor this type of operation. INTRODUCTION The Cook Ranch Field is the largest of a number of relatively small, shallow producing areas near .Albany, in Shackelford County, Texas. This field is one of the first to be operated by gas injection in Texas, and probably is the most successful low pressure gas injection project ever attempted. The field is owned entirely by Koeser and Pendleton, Inc., and Continental Oil Co., and has been operated by Roeser and Pendleton, Inc., since it was discovered. This study has been made possible through the cooperation of Roeser and Pendleton, Inc.. in making availahle a remarkably complete set of records covering all phases of their operations. The purpose of this paper is to present a summary of the history of the operations through Dec. 31, 1950, and to analyze some of the factors which appear to be responsible for the success of the project. Information concerning the physical plant and the early gas injection history has been presented in an earlier paper.&apos; RESERVOIR CHARACTERISTICS production in the Cook Ranch Field is from a large lens of Cook Sand. of lower Permian or upper Pennsylvanian age, occurring at an average depth of 1.300 ft. The average dip of the sand body, as shown in Fig. 1. is only about 50 ft per mile to the northwest. The reservoir has an area of 930 acres and contains 15,512 acre-ft of Sand, consisting of about 14.512 acre-ft of produc-tive oil zone. and an estimated 1.000 acre-ft of primary gas-cap. The iso-pachous map (Fig. 2) was prepared from drillers&apos; logs. Recent coring in the field has proven these logs to be quite accurate. The productive limits of the field are defined by shale on all sides but the southwest where a small zone of edgewater was encountered. This water does not appear to have encroached into the reservoir, and water production has been small. A smaller producing area to the south of the Cook Ranch Field also produces from the Cook Sand. but is separated from the reservoir under consideration by a band of shale. The sand consists of well sorted, coarse grained. rounded and subangu-lar quartz fragments. very poorly cemented. The analysis of 46 chip-core samples from two recently completed test wells indicates a range of porosity values between 12.5 and 28.2 per cent. wit11 an arithmetic average of 24.0 per cent. Air permeability values range between 50 and 2,300 md, with an arithmetic average of 1.200 md. The reservoir where cored is a Solid sand body. with no discernible major shale breaks or impermeable streaks. Vertical permeability appears to be of the same magnitude as the horizontal permeability. A core of the Cook Sand was cut ill the smaller field to the south, using lubricating oil as drilling fluid. The connate water content of the sand in this core was found to average about ten per cent, and the porosity and permeability were comparable with the values reported above. No analysis was made of subsurface or recombined hydrocarbon samples,

Jan 1, 1952

By H. H. Stout

IN the early fall of 1025, the writer was conducting, in the Ledoux and Co. labora-tory, New York, experiments directed to-ward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point. The apparatus consisted of a vertical I-in. dia. silica tube about 12 in. long, heated on the outside. The cathodes were broken to pass 3/8-in. mesh, and a current of various differ-ent gases was passed up through a 4-in. long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to 1500° to 1600°F. and the gas treatments lasted from 3 to 6 hr. The writer observed that whenever reducing gas (H2 or CO) was used, these cathode par-ticles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc., had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500°F." Smoot&apos;s reaction, after a few moments considera-tion, was, "It looks perfectly all right to me." The writer and his assistants, W. H. Osborn and H. H. Stout, Jr., after confer-ring as to ways and means, decided to go ahead with preliminary laboratory experi-ments, which, it was thought, would move the new process from the possible to the probable. This program followed a course indicated by three basic considerations: I. Since brittle cathodes were often unin-tentionally produced, it seemed probable that the laws controlling this type of deposi-tion could be ascertained. 2. We had already proved the gas-clean-ing feature. 3. There remained to prove: whether a sound, homogeneous metal billet could be produced with crystal growth established over the entire surface of each individual particle in the billet; and, if so, what would be the physical properties? Osborn arranged with Columbia Uni-versity for conducting experiments in its research laboratory to prove or disprove the third item; Columbia assigned C. A. Phillipi, Jr. to assist in the project. A press with a cylinder 2 in. high and of I-in. dia. was used. It was surrounded and heated by a resistance coil of Nichrome wire. Broken tough cathodes were used.

Jan 1, 1940

By R. Q. Shotts

This paper is a review of recoverable reserves of bituminous coal in the Southern Appalachian area, according to the latest published estimates. A few comparisons are made, some apparent trends are discussed, and some comments are made regarding the limitations of present estimates. The definition of Southern Appalachian area used in this report is somewhat arbitrary. It includes all the bituminous coal deposits of Alabama, Georgia, and Tennessee. All of West Virginia has been excluded. The East Kentucky and Virginia counties included were selected in connection with a literature study the writer made in 1959 of possible coal supply areas for the Tennessee Valley Authority. The selected counties were considered to be the only ones from which TVA might expect to obtain coal. The availability of coal from some of these counties is doubtful, but no other East Kentucky counties were considered more than remote possibilities. With these limitations, the Appalachian area covered is that from which producers of electric power and steel and commercial coal users, located in the Southeastern U. S., may expect to obtain their supplies of coal. Of course, it is recognized that coal from the eastern interior fields is also available to many of these same organizations. RANK AND QUALITY OF THE COALS Practically all the coals in the Southern Appalachian region are of high volatile A bituminous rank. An occasional sample indicates a slightly lower rank, but such samples may be oxidized or otherwise not representative. Some thin beds in Lookout Mountain and Sand Mountain in Alabama and Georgia, are low volatile bituminous coals, but they have not been mined extensively in modern times. There is a possibility that some of the deeper beds along the southeastern edge of the Warrior field of Alabama are near the Low-medium volatile bituminous dividing line. The Sewanee bed and some other minor ones of the Southern Tennessee field, some of the lower beds in Virginia, many beds in Sand and Lookout Mountains in Georgia and Alabama, one or more beds in the Coosa field, possibly some lower beds in the Cahaba field, and most of the beds along the southeastern edge of the Warrior field and the southern end of the Sequatchie anticline of Alabama, are of medium volatile bituminous rank. The quality of the Southern Appalachian coals is highly variable. Some of them, particularly such prevailingly thin ones as the Black Creek bed of Alabama and the Straight Creek bed of Kentucky, are unusually low in mineral matter— probably the lowest in the U. S. With the exception of certain beds and local areas, Alabama and East Kentucky coals probably have as low average ash and sulfur content as can be found in any sizeable coal area in the country. The sulfur content of Southern Appalachian coals is also variable, but few beds are consistently high in sulfur. In Alabama, sulfur generally increases from southeast to northwest across the Warrior field, but this trend is not quite as clear in the other states. A few beds in Northern Tennessee are prevailingly high in sulfur. All Southern Appalachian coals are potential coking coals if they can be prepared to meet chemical requirements. Only a comparatively small part of the medium volatile A bituminous coal, but most of the medium volatile bituminous coal mined is actually used for coking purposes. An estimate of reserves of coking coal under the requirements of present practice, could be compiled comparatively easily, but this probably has never been done. The reserve of coal that can be coked as an ingredient of a suitable blend is probably many times the size of the reserves of coal that will yield suitable blast furnace and foundary coke without blending. WHAT CONSTITUTES ECONOMICALLY RECOVERABLE COAL RESERVES? When one first realizes the vast extent of the coal-bearing rocks in the Southern Appalachian area, (see Fig. 1) the thought is likely to occur that the supply of coal is inexhaustible. This is particularly true on realizing that in some of the basins of thicker coal-

Jan 1, 1962

By L. W. Holm

This study shows that in the presence of foam, gas and liquid flow separately through porous media representative of reservoir rock. These results were obtained by using tracer techniques to measure the flow of the gas and liquid comprising the foam. Foam does not flow through the porous medium as a body even when the liquid and gas are combined outside the system and injected as foam. Instead, the liquid and gas forming the foam separate as the foam films break and then re-form in the porous system. Liquid moves through the porous medium via the film network of the bubbles and gas moves progressively through the system by breaking and re-forming bubbles throughout the length of the flow path. The flow rates of the gas and liquid are a function of the number and strength of the films in the porous medium. There is no free flow of gas; i.e., no continuous gas phase. On the basis of these results, foam can be expected to improve a water flood or gas drive by decreasing the permeability of the reseruoir rock to a displacing liquid or gas. This improves the mobility ratio and thus the conformance of the flood. INTRODUCTION Foam is formed when gas and a solution of a surface active agent are injected into a porous medium either simultaneously or intermittently. During the past few years, several papers have been published on the subject of foam flow in Dorous media. Foam has been used successfully in the removal of capillary water blocks from producing formations.&apos;&apos;2 The use of foam in gas storage reservoirs to reduce gas leaks and to increase storage capacity has been considered in recent years. Foam has also been investigated as an oil displacing agent,3-5 and as an agent to improve the mobility ratio in a waterflood.6-10 However, the mechanism by which the gas and liquid phases comprising the foam flow through a porous medium has nor been described adequately. Normally, when two immiscible phases (gas and liquid) flow concurrently through a porous medium, each phase follows separate paths or channels. At given saturations of the two phases, a certain number of channels are available to each phase, and as saturations change, the number and configuration of the channels available for each phase also change. The effective permeability of each phase is a function of the saturation of that phase only, and the flow of each phase can be described by Darcy&apos;s law. When foam is present, the effective permeability of the porous medium to each phase is greatly reduced compaced with permeabilities measured in the absence of foam.6,11-13 Based upon the observed flow of surfactant solutions and gas in capillaries, it has been concluded that the gas and liquid may flow separately or they may flow combined as foam. At least four mechanisms have been postulated to explain how fluids flow with foam present: 1. A large portion of the gas is trapped in the porous medium and a small fraction flows as free gas, following Darcy&apos;s law.9 2. The foam structure moves as a body; the rate of gas flow is the same as the rate of liquid flow. 6,13 3. Gas flows as a discontinuous phase by breaking and re-forming films. Liquid flows as a free phase.12 4. A portion of the liquid and gas move as a foam body while excess surfactant solution moves as a free phase.14 It also has been suggested that different flow mechanisms exist for high quality (dry) foams made from dilute surfactant solutions and for foams made from more concentrated solutions. Studies conducted on the flow of foam through capillaries have shown that a plug-type flow occurs and that foam flows as a body.6,15 Fried also has described the flow of foam through porous media as

Jan 1, 1969

The following additional notes about prices of coal in the early days were collected from the sources shown. Several data about canal tolls and labor conditions are also included. 1796, November: "The inhabitants lay it (coal) in at about 3;d. (83¢) sterling per bushel." (Ref. 73: p. 147.) 1804, March: "In March, 1804, I sent a person accustomed to mining to open the vein of coal, and to load the ark, which was accomplished, and early in the month of April the ark, with the first cargo of bituminous coal passed safely the Conewago falls, and landed her coal at Columbia, Lancaster County. The coal was sold at 31¢ per bushel at Columbia." ($7.75 per ton). This was the first coal from Clearfield County near the town of that name. (Letter from William Boyd: Pa. Senate Jour., 1833-1834, vol. 2, p. 561.) 1807: The following notice appeared in the Bedford Gazette: "Huntingdon, June 4. "Stone Coal.-Such of the farmers as wish to make experiment with stone coal as a substitute for plaster, in manuring their Indian corn, may be supplied with coal gratis upon application to Peter Hughes, at Mr. Riddle&apos;s mines, on the Raystown Branch. The proprietor of the mines offers not only to refund the carriage, but to pay the expenses of applying the coal, if upon a fair experiment it is found to be inferior to plaster, which now sells at two dollars per bushel." (Ref. 735: p. 708.) 1809: Coal was delivered in Pittsburgh at 5¢ per bushel or $1.25 per net ton. (Ref. 444: p. 50.) Coal was delivered in Connellsville at 4¢ per bushel or $1.00 per net ton. (Ibid.: p. 185.) 1810: Pittsburgh.-"Coal may be obtained of a good quality, ready delivered at 5¢ a bushel." ($1.25 per net ton.) (Ref. 315: vol. 2.) 1811: "It (coal) costs 6¢ a bushel at your door." ($1.50 per net ton.) (In Pittsburgh.) (Ref. 277: 1811, p. 68.) 1814: At Columbia, now part of Donors, Washington County, Pa., an original sale of lots in 1814 gave the purchaser of each lot the right to mine stone coal gratis from a bank on the property. (Ref. 410: vol. 1, p. 547.) "A laborer is able to dig upwards of 100 bushels per day." (4 tons.) (Ref. 277: 1814, p. 109.) A paper about the early newspapers in West Virginia says: "Collier Wanting. From 10 to 20 steady and industrious men, who understand digging coal, may obtain high wages in Kenhawa for that business, if immediate application is

Jan 1, 1942

By John L. Ham, Robert M. Parke

THE melting point of molybdenum is 2625° ± 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. 1, 1944, to Aug. 31, 1945, the project was under the supervision of the National Defense Research Committee, Division One. In peacetime, too, there are needs for molybdenum, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. FIRST PROCESS FOR MELTING AND CASTING MOLYBDENUM The maintenance of a temperature greater than 2625°C. in a space large enough to melt several pounds of molybdenum may involve the loss of heat at a very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum. In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1946

By S. WHINERP

(Cleveland Meeting, October, 1912.) I AM indebted to L. E. Bryant, of Danville, Ky., President of the Virginia Mining Co., operating coal-mines in Scott county, Tenn., for the following information relating to the existence of the Clinton iron-ore under the NW. slope of the Cumberland Plateau in Kentucky and Tennessee. During the past 15 years quite an important oil-field has been developed in a region having Wayne county, Ky., as its center, and a large number of wells have been drilled in that and adjacent territory in the search for oil. Many of&apos; these wells have been carried to considerable depths below the recognized oil-bearing horizon, and one of them was drilled by Mr. Bryant at Pine Knot, a station on the Cincinnati, New Orleans & Texas Pacific railroad, a few miles north of the point where that road crosses the Kentucky-Tennessee State-line. The elevation of the surface at the crossing is about 1,400 ft. above sea-level. The railroad is located on the dividing ridge between the Cumberland river and Big South Fork. At a depth of 1,720 ft. below the surface the drill reached and passed through a formation which the drillers called " red rock," but which Mr. Bryant classified as Clinton iron-ore, as its geological position corresponded to that formation. The ore at this point was 6 ft. thick and appeared to be of uniform quality throughout. An analysis of the drillings gave : Fe, 33; Mn, 0.25; Si02? 3 ; Al203, 2 ; CaO, 13; MgO, 7 ; P,05, 0.333 per cent. ; S, trace. This analysis seems to confirm the belief that the ore is Clinton, and that it is of a quality equal to the average of the deep or unbleached Clinton ores in Tennessee and Alabama. This discovery led Mr. Bryant to make further examinations and inquiries, and he found that the stratum called " red rock " by the drillers had been passed through and noted in the great majority of the wells carried down to the same geological hori-

Oct 1, 1912

By J. L. Brimhall, R. A. Huggins

The structure of deformed internally oxidized alloys of siluer- cotztcrining magnesium and copper-containing aluminum in was studied by thin-film transrrzissiotz electron microscopy. With low to moderate amounts of stvain, the deformation structure in t11e dispersion-hardened alloys was found to consist of a high density of dislocations arranged it a random distribution or in a very fine, but poorly defined, cell stucture, depending on the fitness of the dbsbersion and amount of deformation. 112 contrarst, both pure copper and silver show relative1y Large, distinct cell structures. The particular structures in the alloys are believed to result from particles acting as both dislocaliot~ sources and deflector-s. The Inck of a pvorzolrr~ced deformation texture tr~ regiotzs qf&apos; seoere loctll plastic curvature after heavy deformation can also be traced to the formation of clislocntions on many slip systemes and a lack 01 local concentrations of dislocations of predominantly one sign. THE presence of fine dispersions of a second phase has long been known to have a strong influence upon the mechanical properties of solids. Until recently, the influence of particles on the deformation mechanisms has been assumed to be solely that of barriers to dislocations. This is seen in the classic models of edge dislocations being restrained by the particles.1 4 There is, however, considerable evidence that this is not their primary effect, and that the particles can have a large influence on the defect structure generated by plastic deformation. The presence of particles causes changes in the surface topography observed after deformation. In overaged precipitation-hardened materials containing hard, noncoherent precipitates, fine intersecting slip lines are found after deformation of single crystals. indicating the activation of many slip systems. This has been extensively observed in the A1-Cu systen;, both by optical microscopy and replica electron microscopy.&apos;"13 In some of the observations. the slip lines were seen to extend between the particles. Similar observations of extremely fine slip lines or the apparent absence of normal slip lines have also been found in A~-M~."

Jan 1, 1965