Search Documents

By R. J. Piros, Brusenback, D. A. Dahlstrom

DEWATERING fine coal has been a serious problem to many operators who desired to wet-wash finer sizes and maintain high recovery. Centrifugal driers have become popular for this purpose for sizes between 3/8 in. and 14 mesh. Below 14 mesh the perforated screen centrifuges lose a large per- cent in the effluent solid bowl types that do retain -14 mesh coal, produce excessive degradation, tend to retain the highest ash fraction in any size fraction, and are subject to abrasion, which results in higher maintenance. In 1949 Truax-Traer Coal Co. planned a cyclone installation at their Ceredo preparation plant to recover coal down to 150 mesh with approximately a 14-mesh top size. Since available centrifugal equipment was not considered satisfactory, an investigation of rotary vacuum filters was begun in cooperation with the Peterson Filters and Engineering Co. to determine the suitability of the Peterson Top Feed Reservoir (TFR) filter. This investigation, which is described below, has resulted in a highly satisfactory installation of two 6x10-in. Peterson TFR filters that have been in operation over a year. After some preliminary laboratory batch vacuum filter tests, a pilot plant double-drum Peterson TFR filter was installed at Ceredo to prove the feasibility of vacuum filtration and determine optimum conditions. The full scale units were then installed on the basis of the pilot plant results. This was followed by an extensive research program on vacuum filtration in the laboratory at Northwestern University to investigate basic design and operating variables and their influence on final moisture con- tent of the filter cake. A method of scale-up from laboratory batch tests to the full-size unit was also proposed and proved. Because of the importance of dewatering fine coal today, it was felt that the results of the three steps should be made available for the use of others facing this problem. The work at Northwestern is given in a theoretical section following the discussion of the pilot plant and full- scale operation. Fig. 1 is a flow diagram of the cyclone and filter installation. The feed is drawn from below the

Jan 1, 1952

By Louise Barton Freeman, Coleman D. Hunter

The total production of oil in Kentucky during the year 1943 reached 7,010,776 bbl., which is more than at any time since 1930. Of this total, 5,287,659 bbl. was produced from the counties west of the Cincinnati arch, 692,359 bbl. from the 18 new pools opened during the year, and 3,260,765 from the Smith Mills pool, which was discovered in August of 1942. This is an important increase in western Kentucky in spite of the low price of crude, and demonstrates effectively the desire of the industry to cooperate in meeting the increased demands made by the war. Western Kentucky Two deep tests were drilled in the Kentucky portion of the Mississippi Embayment this year. Both were drilled to test the St. Peter. One well, drilled in Marshall County by the Adams Oil and Gas Co., did not encounter any St. Peter sandstone but drilled 650 ft. of formation below the position of the St. Peter and above the true Knox dolomite. The other well, in Ballard County, was reported to have tested the St. Peter and to have been temporarily abandoned at 3069 ft. At this depth the well probably was stopped in about the same formation as the Marshall County well. No accurate information is available on the Ballard County well. Several new producing areas were added to the list of fields in the western Kentucky coal basin, in Daviess, Henderson, McLean, Ohio, Union and Webster Counties. The Smith Mills pool was enlarged and production was found in the McClosky (Ste. Genevieve) in addition to the Cypress sandstone from which much of the earlier production had been obtained. There was some interest during the year in testing the Devonian and Silurian formations in the area south and east of the western Kentucky coal basin. In the fall of 1943, a 15 to 20-bbl. well was drilled in Allen County and two more wells are now being drilled. The production was obtained from within a few feet of the base of the Chattanooga black shale, probably in the upper Silurian. One well in Simpson County was drilled completely through the Silurian section before it was abandoned. Several wells were drilled in Logan, Todd and Christian Counties to test the Devonian where it is thinned by removal of the upper formations before deposition of the Chattanooga shale. None of these wells was successful but several other locations are now being tested. The Silurian thins in like manner on the eastern flank of the coal basin as the crest of the Cincinnati arch is approached, and it is along this thinning edge that such fields as the LeGrande, Logsdon Valley, Magnolia, Bowling Green and the Barren County pools were developed. A number of wells were drilled around these old pools in an effort to extend them, some of which were successful. The wells listed this year in Larue, Hardin, Barren, Hart and Warren Counties were drilled in the search for other such fields.

Jan 1, 1944

By L. S. Darken, H. A. Wriedt

THE constitution diagram of the iron-copper system derived by Daniloff' exhibits, at the iron-rich end, phase fields similar to those of the iron-carbon diagram. At 1484° 1094°, and 850°C there are, respectively, a 6-y-L peritectic, a y-E-Lperitectic, and a a-y-E eutectoid. The phase designated E is copper-rich, containing 4 pct Fe or less according to the temperature. The composition of copper-saturated ferrite (a-solid solution) has been determined previously only twice as a function of temperature. By electrical conductivity measurements, Buchholtz and Köster2 found 3.4 pct Cu in ferrite at a eutectoid temperature of 810°C. They represented the composition of saturated ferrite by the equation, log (%Cu) = 4.32-4125 (1/T) Gregg and Daniloff3 reported that Köster later modified his opinion, raising the indicated eutectoid temperature to 833 °C and the copper content of eutectoid ferrite to 3.7 pct. The literature contains several indications4-7 that the work of Köster and his co-workers is not reliable. Norton,8 using an X-ray method, found that 1.4 pct Cu dissolved in ferrite at the approximate eutectoid temperature of 850°C and that the solubility decreased to about 0.3 pct at 700°C. Below 700°C his experimental data show almost no change in solubility. These findings, although inconsistent with the work of Ruer and Goerens4 and of Smith and Palmer,7 have been used generally since their publication. In investigations involving the observation of arrests in temperature during continuous heating or cooling the precise location of the eutectoid temperature has been obscured by a large hysteresis. The more reliable work 579 where the results are not effected by this hysteresis indicates a eutectoid temperature between 840° and 850°C. The foregoing discrepancies, along with a few observations in this Laboratory relating to the precipitation of copper from ferrite, prompted us to rein-vestigate the lower temperature portion of the Fe-Cu system. In this investigation the solubility of copper in ferrite was obtained by the chemical analysis of high-purity iron equilibrated with copper-silver alloys. This method eliminated the necessity for retaining by a quench the physical state of the specimen existing at the equilibration temperature. EXPERIMENTAL The reaction of the iron with the copper alloy was

Jan 1, 1961

By W. P. Sykes

SINCE Honda and Murakami1 in 1918 proposed their constitutional diagram of the carbon-free iron-tungsten system, considerable effort has been expended by several investigators in attempts to define more positively the structural features of the alloys. The existence of an intermediate phase corresponding to the formula Fe3W2 (68.7 per cent W) was proposed from evidence of a purely metallographic nature by one of the present authors2 in 1926. Since that time the identity of this phase has been confirmed by Arnfelt3 and by Takeda,4 both of whom employed X-ray methods as well as the microscope and the chemical analysis of isolated microconstituents. According to Arnfelt, Fe3W2, as crystallized from the iron-rich melts at a temperature above 1450'C., contains by analysis 68.7 per cent W. The lattice of this phase is characterized by trigonal symmetry. Arnfelt, moreover, proposed a second intermediate phase formed at some temperature between 1450° and 1000° C. by a peritectoid reaction involving Fe3W2 and the iron-rich solid solution. A melt containing 25 per cent W was cooled to 1000° C. and heated for. 100 hr. The precipitated tungsten-rich constituent was separated and found by analysis to contain 62.6 per cent W. This composition agrees closely with that represented by the formula Fe2W (62.2 per cent W). Diffraction patterns from the concentrated precipitate showed a hexagonal unit cell. Takeda confirmed the data of Arnfelt regarding Fe3W2 but was unable to detect Arnfelt's second intermediate phase. While Takeda. failed to describe in detail the treatments employed, he stated that in alloys containing 40 per cent W which were quenched after heating at various temperatures between 1200° and 1450° C., no evidence of the second phase (Fe2W) was observed either in the microstructure or in the diffraction patterns of isolated residues. He therefore considered the existence of this low-temperature hexagonal compound as disproved.

Jan 1, 1932

By G. S. Ansell, J. Weertman

The creep behavior of an aluminum alloy hardened with a finely dispersed phase of aluminum oxide was investigated. The as-extruded alloy shows an approximate steady-state creep in which the creed rate depends exponentially on the applied stress. The activation energy of creeb is abbroximately 150,000 cal per mole. The recrystallized alloy shows no steady-state creep. ONE method of improving the creep resistance of a metal is to introduce a finely dispersed second phase into the metal matrix. The improvement of the creep resistance has been qualitatively explained by assuming that the dispersed second-phase particles act as obstacles to dislocation motion. If the main effect of second-phase particles is simply to hinder dislocation motion then it is possible to derive a high-temperature creep equation for a dispersion-hardened alloy in a straightforward manner. In the Appendix of this paper such an equation is derived from a creep model which works very well for pure metals. Recently, F. V. Lenel has fabricated, for the first time, powder extrusions of aluminum-aluminum oxide in a large-grained recrystallized form. This alloy, designated as MD 2100, consists of a fine dispersion of aluminum oxide plates in a matrix of commercial purity aluminum. A considerable amount of investigation has been carried out concerning the microstructure and physical properties of this alloy.&apos; ) The aluminum oxide is present in the form of flakes 130A units thick and 0.3 u on edge. They are dispersed in the aluminum matrix with an average spacing of approximately 0.5 jx. The spacing varies in the range of 0.05 to 1.5 µ. The alloy structure is extremely stable at high temperatures. For this reason the alloy offers a unique opportunity for a fundamental study of creep of a very finely dispersed two-phase alloy. Lenel supplied specimens in both the unrecrystallized and recrystallized condition. This paper reports high-temperature creep experiments carried out on these specimens. The results obtained were rather unexpected. No steady-state creep was observed in the recrys-tallized material. In fact, after some transient creep which takes place upon loading, the creep rate is essentially zero ( < 10-8per min). If the second-phase particles acted solely as obstacles to the motion of dislocations, measurable steady-state creep would be expected. Since none is observed it appears that the main effect of the fine dispersion in the recrystallized material is to inactivate the dislocation sources themselves, rather than hinder the motion of dislocation loops created at these sources. EXPERIMENTAL DETAILS Specimens were tested in wire form, 0.087 in. in diam for the as-extruded alloy, and 0.035 in. in diam for the recrystallized alloy. These samples were held in friction-type wire grips; a gage length of 2.5 cm was used for all the creep tests. The specimens were held at 600°C in the test apparatus for at least 15 hr prior to each test. The tests were run under the condition of constant loading and, since the creep strains were small, can be considered as constant stress tests. The temperature of testing was held constant within 3°C. Elongations were measured with an optical cathetometer which was capable of measuring strains as smaIl as 0.00012. This allowed the measurement of strain rates as low as l0-8&apos;per rnin. In addition to the creep tests optical micrographs were made in order to determine both the grain size and microstructure of these materials. RESULTS Fig. 1 shows a few typical creep curves obtained from the as-extruded material. The elongations were somewhat erratic, but each curve shows a region of quasi-steady-state creep from which an approximate steady-state creep rate can be obtained. In general the higher the stress at a given temperature, the greater the total elongation before fracture. The lower the applied stress, the longer is the region where the creep rate is almost constant. Summary data from the creep tests of the as-extruded material are listed in Table I. The steady-state creep data of the as-extruded material for a range of stresses at a constant temperature follow a creep equation of the type creep rate = K&apos; = A exp (&) [11 where A and B are constants, k is Boltzmann&apos;s constant, T is the absolute temperature, and a the stress. The standard error of estimate of the data received is less than one order of magnitude. As shown in Fig. 2, if one compensates the creep-rate data for the effect of temperature over the range of test temperature, the steady-state creep data roughly follow a creep equation of the type Temperature compensated creep rate = K* = A exp

Jan 1, 1960

By L. Seigle, R. Resnick

An inert-marker movement experiment indicates that the ratio of the intrinsic diffusion coefficients DC:DTa = 80:l in TaC at 2500°C. Measurements of the diffmion coefficient of carbon in nonstoichiometric TaC at temperatures from 1700° to 2700°C reveal that Dc increases with decreasing carbon content, but much less than expected from the probable change in vacancy concentration with carbon content. A diffusion process involving two simultaneously operating mechanisms is postulated, and shown to be theoretically feasible. The average value of the carbon diffusion coefficient is given by DC = 0.18 exp[(-85,000 ± 3000)/RT] sq cm per sec over the composition range 46 to 49.5 at. pct C. BECAUSE of their high melting points and hardness, the carbides of the IV, V, and VI group transition metals, along with those of uranium, have attracted considerable interest for applications at high temperatures. In these applications the reactivity of the materials is important, and, since rates of diffusion within the compounds influence reactivity, a knowledge of diffusion kinetics and mechanisms is desirable. While many investigations of the mechanical and electrical properties of these compounds have been made, only two fundamental investigations of diffusion in the carbides are known. Chubb, Getz, and Townleyl measured the diffusivity of carbon and uranium in UC, and Gel&apos;d and Liubimov2 measured the diffusivity of carbon and niobium in NbC. This paper describes an investigation of the diffusion of carbon in tantalum monocarbide and, in particular, the influence of carbon deficiency on this process. Tantalum carbide melts at approximately 3800°C, which makes it one of the highest melting materials known. The compound exists over a rather wide range of carbon Content.3-7 At the peritectic temperature, 3240°C, the phase extends from about 36 to 50 at. pct C. Although the compound can exist with a substantial carbon deficiency, the high carbon phase boundary remains near the stoichiometric composition over the entire temperature range; i.e., no carbon excess is observed. The structure of TaC is the NaCl type wherein carbon atoms normally occupy the octahedral sites in a somewhat expanded fcc lattice of tantalum. Decrease of the lattice parameter with decreasing carbon suggests that the removal of carbon introduces octahedral vacancies into the lattice. I) EXPERIMENTAL DETAILS AND RESULTS Inert-Marker Experiments. In a compound such as TaC the interstitial element would be expected to diffuse more rapidly than the metal. This was confirmed by an inert-marker experiment, following Srnigelskas and irkeendall.8 Ideally, the markers should be placed at the interface between a slab of low-carbon TaC and graphite, and their movement during subsequent inter-diffusion measured. Unfortunately, no solid could be found which is unreactive in contact with carbon at the high temperatures employed in these experiments. In order to circumvent this problem, a specimen was designed in which the markers consisted of several small canals running just below the surface of a tantalum slab. This specimen was prepared by machining grooves on the surface of the tantalum slab and then diffusion-bonding a thin plate of tantalum to the slab over the grooves. The surface of the plate was then ground down until the distance between the canals and surface was as small as possible (about 0.01 cm). Thus, the canals would lie entirely within the TaC phase after a short period of diffusion. The diffusion anneal consisted of immersing the metal sample in high-purity graphite powder and heating for approximately 10 hr at 2500°C under vacuum. At this temperature, the vapor pressure is sufficiently high and the transfer of carbon from graphite sufficiently rapid to allow the surface of the diffusion sample to attain the stoichiometric carbon concentration very quickly. Conclusions regarding the relative diffusion rates of carbon and tantalum in the compound layers (TaC and Ta2C) can be drawn from the location of the canals after the diffusion anneals. If the growth of the layers is governed mainly by the diffusion of carbon, as expected, the canals should remain close to the sample surface. If the diffusion of tantalum contributes appreciably to formation of the compound layers, the distance from the markers (canals) to the surface should increase. Fig. 1 shows, diagrammatically, the appearance of the specimens after diffusion, and Table I presents the depth below the surface at which the

Jan 1, 1967

By D. L. Wood, J. H. Westbrook

The tensile behaviors of the CsCl structure compound AgMg are extensively documented in terms of strain, strain rate, temperature, composition, and metallurgical processing treatment. The observations lend themselves to presentation in terns of three regimes of deformation behavior; 1) low temperatures where deformation is primarily by slip; 2) intermediate temperatures where the deformation mode is also slip but with the detailed behavior dominated by dislocation interactions with solute atoms; 3) high temperatures where defomation is primarily by diffusion controlled processes. Of all the material groups of potential interest as high-temperature structural materials, the inter-metallics have been the least studied, particularly with respect to their mechanical behavior. Moreover, the application and processing of intermetallics for uses which exploit their often unique physical properties have been impeded by a lack of understanding of their mechanical properties. Previous work in this area* has been largely *For a recent review, see Westbrook.&apos; exploratory, aimed on the one hand at the direct empirical development of materials of engineering utility and ,on the other at identification of the important parameters affecting the mechanical behavior of inter metallics. As a consequence, there has not been available, heretofore—for any inter-metallic—data, sufficient in extent or precision to provide an adequate phenomenological description of the effects of metallurgical variables on deformation behavior. Such documentation is prerequisite to intelligent application or processing design and is also necessary for testing present and future theoretical analyses of mechanical behavior. It was therefore an objective of the present investigation to document the deformation behavior of a simple ordered intermetallic over as wide a range as possible of all the usual metallurgical variables. The compound AgMg was chosen as the subject of this investigation because it met all of a group of desired criteria, namely: 1) congruent but moderate melting point; 2) simple crystal structure; 3) ordered structure persisting to the melting point; 4) broad solubilities for the component elements. The first and last criteria were expected to aid in the preparation of homogeneous single-phase specimens: the second and third to help simplify the

Jan 1, 1962

By Francis T. Freeland

The deeper workings of the Leadville mines show refractory ores, consisting principally of sulphides of iron, lead, and zinc, carrying silver, in place of the easily reduced carbonate ores lying nearer the surface. The largest and most extensively developed deposit is that of South Iron Hill.* It lies on the north side of California Gulch,

Jan 1, 1886

By Walter Weeks

THERE is very little useful material in the litera-ture on the construction of manometers, so each experimenter must devise his own instrument. I have experimented for a number of years and have finally built one that is satisfactory. If we are to obtain accurate friction factors in mine-ventilation problems we must use accurate instruments. The most simple and convenient instrument for the mea-surement of small pressures is the inclined manometer or U-tube. By changing the angle at which the tube is set, any desired magnification of the pressure reading may be obtained. The first question in regard to the manometer is: What liquid shall be used? Alcohol, in my opinion, is the best. It does not cling to the glass and it does not attack the rubber tubes. The next problem is the setting of the instrument at the proper angle. One method is illustrated in Fig. 1. The base plate AC is made horizontal by a level bubble. The plate AB, which carries the U-tube, is hinged at A. The angle z which AB makes with the horizontal may be made any value by pinning the end B at the calculated position on the arm CD. Such an instrument may be designed to read directly in inches of water if a liquid of constant specific gravity is used. If the specific gravity varies, a calculation is necessary to convert the reading into inches of water.

Jan 1, 1923

By C. J. Ramsburg

The construction and operation of by product coke-oven plants in America are essential to strong national defense and of the greatest importance to many widely diversified undertakings as well as to safety and health. Carbonization Process Coal used under a boiler or in a locomotive is consumed by combustion. Coal used in a by-product oven is distilled or carbonized, meaning that heat is applied to the coal, out of contact with air, causing a distillation that removes the volatile matter in the coal in the form of gas and vapor, leaving coke as a final product. From the gas and vapor distilled from the coal, many valuable substances can be secured, known as by-products. Hence the name "by-product oven." The simplest example of this principle can be shown by means of an ordinary clay pipe. If powdered coal is placed in the bowl of the pipe, the opening of the bowl is plugged with clay, and the bowl placed in a flame, the bowl will become hot, transferring the heat through the wall of the bowl to the coal within. When this coal attains a temperature of about 750°F., gas will begin to pour out of the pipe stem, and this gas may be lighted. A black liquid also will exude from the stem of the pipe, This is tar mixed with certain other products. What remains in the bowl after distillation is coke. A coke oven corresponds to the bowl of the pipe. A modern oven of the latest type is a refractory brick chamber approximately 42 ft. long and 14 ft. high, averaging 18 in. in width. The oven is filled with coal through closable charging holes in the oven top. Each end of the oven consists entirely of a self-sealing door, the removal of which permits the finished coke to be discharged by means of a power-operated pusher machine. The ovens are built in batteries, and the heating is effected by gas burned in vertical flues in the oven walls, each set of flues heating the walls of two adjacent ovens. Such ovens carbonize a charge of approximately 18 tons of coal in 18 hr., or have a daily throughput of 24 tons per oven, producing about 17 tons of coke. In times of need, the output may be increased by raising the temperature of flues, thus shortening the coking time. There is one great essential difference in principle between distillation in a clay pipe and in a coke oven. In the 18-in. oven, the distillation proceeds from two parallel walls held at a high temperature (over zooo°F.) and instead of all the coal being heated at once, the distillation is a progressive one creeping inward. The average travel of this heating is 35 in. per hour from each vertical wall, and as the volatile products are formed progressively they must push away from the interior toward the wall through the previously formed hot coke, then up the walls and Over the top of the coal charge, finally escaping through the outlet pipe. This results in a cracking of the components into many different and valuable substances not formed when the carbonizing temperature is low.

Jan 1, 1942

By C. J. Ramsburg

The construction and operation of by product coke-oven plants in America are essential to strong national defense and of the greatest importance to many widely diversified undertakings as well as to safety and health. Carbonization Process Coal used under a boiler or in a locomotive is consumed by combustion. Coal used in a by-product oven is distilled or carbonized, meaning that heat is applied to the coal, out of contact with air, causing a distillation that removes the volatile matter in the coal in the form of gas and vapor, leaving coke as a final product. From the gas and vapor distilled from the coal, many valuable substances can be secured, known as by-products. Hence the name "by-product oven." The simplest example of this principle can be shown by means of an ordinary clay pipe. If powdered coal is placed in the bowl of the pipe, the opening of the bowl is plugged with clay, and the bowl placed in a flame, the bowl will become hot, transferring the heat through the wall of the bowl to the coal within. When this coal attains a temperature of about 750°F., gas will begin to pour out of the pipe stem, and this gas may be lighted. A black liquid also will exude from the stem of the pipe, This is tar mixed with certain other products. What remains in the bowl after distillation is coke. A coke oven corresponds to the bowl of the pipe. A modern oven of the latest type is a refractory brick chamber approximately 42 ft. long and 14 ft. high, averaging 18 in. in width. The oven is filled with coal through closable charging holes in the oven top. Each end of the oven consists entirely of a self-sealing door, the removal of which permits the finished coke to be discharged by means of a power-operated pusher machine. The ovens are built in batteries, and the heating is effected by gas burned in vertical flues in the oven walls, each set of flues heating the walls of two adjacent ovens. Such ovens carbonize a charge of approximately 18 tons of coal in 18 hr., or have a daily throughput of 24 tons per oven, producing about 17 tons of coke. In times of need, the output may be increased by raising the temperature of flues, thus shortening the coking time. There is one great essential difference in principle between distillation in a clay pipe and in a coke oven. In the 18-in. oven, the distillation proceeds from two parallel walls held at a high temperature (over zooo°F.) and instead of all the coal being heated at once, the distillation is a progressive one creeping inward. The average travel of this heating is 35 in. per hour from each vertical wall, and as the volatile products are formed progressively they must push away from the interior toward the wall through the previously formed hot coke, then up the walls and Over the top of the coal charge, finally escaping through the outlet pipe. This results in a cracking of the components into many different and valuable substances not formed when the carbonizing temperature is low.

Jan 1, 1942

By Robert J. De Angelis, James H. Barker

An improved method for solving dynawzical dislocation problems using a digital computer is described in this paper. Interactions between two distinct types of dislocations were studied: attractive screw dislocations; and Lomer lock forming dislocations. One dislocation is positioned in the lattice and is initially at rest, while the other dislocation is moved through the lattice on an intersecting slip plane at a constant velocity in the range 0.5 to 0.999C. (C is the transverse velocity of sound.) The results obtained from these computations indicate that screw dislocations account for a small fraction of the total strain over a wide portion of the range of velocities studied. They further indicate that mixed dislocations mainly repel other dislocations in the neighborhood of the active glide plane. From this a possible explanation for cell formation is put forth. The density of Lomer locks expected to exist after a strain of 0.2 was found to be 1.4 x 106 cm-2 which is in good agreement with indirect experimental estimates. IN the past, predictions of favorable or nonfavorable dislocation reactions were based on the associated changes in elastic strain energy. Such considerations take no account of the probability of the two dislocations coming into contact to react. Venables1 was the first to approach these probabilities by considering the interactions between two moving screw dislocations on perpendicular glide planes. Because of the restrictive types of dislocations and glide plane geometry employed, his results have limited application to metallic crystals. The work to be presented here develops a general approach to solving dynamical dislocation problems; either dislocation-dislocation interactions, presented here in detail, or dislocation interactions with any other suitably defined stress field. Two types of dislocation-dislocation interactions common to face centered cubic (fee) materials are considered: those between pure screw dislocations of opposite sign on intersecting slip planes and those between mixed dislocations on intersecting slip planes, that can react to form a perfect dislocation. This latter reaction, referred to as the Lomer reaction, produces a locked product dislocation that finds it energitical favorable to disassociate into two Shockley partials and a stair-rod dislocation. This partial configuration known as a Lomer-Cottrell (L-C) lock plays a major role in work hardening of fee crystals. seeger2 names the L-C lock as the prime contributor to Stage II hardening while Kuhlmann-wilsdorf3 and Meakin and Wils- dorf4 also state that it is a significant contributor to work hardening. However, with a few notable exceptions,5-7 direct observations of the Lomer lock and the L-C lock by electron transmission microscopy are scanty, and even these are subject to other interpretations.5,6 In a study of partial dislocations present in austenitic stainless steel, whelan8 did not observe any L-C locks at the head of pile-up groups. This result contradicted existing work hardening theories and led him to postulate an alternate theory based on the stress required to break away dislocations intersecting a pile-up group, from their stacking fault nodes. Due to the importance of the Lomer reaction in producing L-C locks which are an essential feature in current work hardening theories and because there exist no data giving direct quantitative values for the density of locks, and because there has even been some doubt expressed as to whether this important reaction occurs at all, a study of the dynamic behavior of the mixed dislocations which form the Lomer lock was undertaken. Due to their ability to cross-slip with relative ease, screw dislocations play an important role in the deformation of fee crystals. For this reason, the second type of reaction considered here is between screw dislocations of opposite sign. In addition, computations in volving screw dislocation interactions are relatively simple, thus providing a convenient check on the cornputational scheme employed. DEFINITION OF PROBLEM The force exerted on a dislocation due to a generalized stress field is given by the Peach and Koehler9 equation: Here t2 and b2 are respectively the tangent and Burgers vectors of the dislocation, and T1 is the stress dyadic defining the local stress field. The stress field may be externally applied or generated internally by the presence of a lattice defect, such as a second dislocation, as is the case in this work. Frank10 has shown that an equivalent momentum, P, of a screw dislocation can be defined by: Here, EST is the total energy of a screw dislocation and ESo is its rest energy. The left side of Eq. [2] is the time derivative of momentum and the right side is the position derivative of the energy due to the dynamical nature of the dislocation. The total energy of a dislocation is the sum of the potential and kinetic energies. Weertman11 has developed the expressions which were used here; these give the potential and kinetic energies of uniformly moving edge and screw dislocations in an isotropic medium.

Jan 1, 1969

By A. B. Cummins

THE past year has been of unusual interest for industrial minerals. It is increasingly evident that requirements for these raw materials move with general economic trends. Thus, with a peak year in the construction, chemical and petroleum industries, the nonmetallic mineral industries have been brought into the complex maze of an economy in which military spending is in the billions and in which the national income and wholesale commodity prices reached new levels. Many industrial minerals are of first rank essentiality in the defense effort and its supporting industries, and since some of these are of limited supply and others dependent on imports, the problems of procurement, distribution and conservation of available supplies make a complicated pattern. Despite some drawbacks and weak spots, the industrial mineral industries have, in general, met the national situation with great credit and many new production records have been set. The general accomplishment in 1951 should be one of satisfaction with confidence for the future. Difficulties, unsolved problems and uncertainties should not obscure the general trend which many consider optimistic. Prices in the main have been upward, in line with the inflation spiral, but nonmetallics appear with some exceptions to be behind the general increases. Labor difficulties have not been serious throughout the year. Retarding influences in expansions and planning have been the uncertainty of the Korean and international situations and a lack of confidence by many in the government economic program and its ultimate impact on the economic structure. It must also be kept in mind that stockpiling, unless all-out war develops, reaches a level and then ceases to be a major sustaining factor in the mineral markets. In accordance with the Defense Production Act of 1950 various control agencies have been set up to establish the desired rate of stockpile acquisitions. The objectives are subject to change depending on availabilities and needs-military, industrial, and civilian. In some minerals there has been disagreement on actual stockpile requirements, and there is some feeling that the needs of defense might be better met if more funds went into the development of new sources of supply of scarce raw materials and more materials were released to industry at this time. Nonmetallic minerals on the strategic and critical list of the Munitions Board as of July 1951 were: Group I; asbestos, some types; bauxite, refractory grade; beryl; celestite; chromite, chemical and refractory grades; columbite; corundum; diamonds, industrial; fluorspar, acid grade; graphite, some types; kyanite; manganese ore, battery and chemical grades; mica, some types; quartz crystals; rare earths; sapphire and ruby; talc, steatite, block; and Group II; bauxite, abrasive; cryolite, natural; diamond dies; graphite, crystalline fines; iodine; mica, muscovite block, stained and lower; rutile; selenium; talc, steatite, ground; zirconium ore, zircon. Details on the current status of stockpiling inventories are not available. The Defense Minerals Exploration Administration has, since April, executed 39 contracts for the exploration of nonmetallic minerals, including twenty for mica, seven for beryl-mica, six for asbestos, three for sulphur and one each for monazite, steatite talc and fluorspar. Total value of these contracts came to $892,059, of which the Government&apos;s participation amounts to $689,247. There were on hand at year&apos;s end another 97 applications for exploration aid on nonmetallic minerals in twenty different

Jan 1, 1952

By L. W. Holm, A. K. Csaszar

A series of laboratory experiments was conducted in which oil was displaced from a porous medium by water-driven slugs of alcohols or similar solvents. The solvents used were soluble to some degree in both oil and water and covered the range of solubilities from complete solubility in oil to complete solubility in water. Displacement experiments were conducted on 2-and 3%-in. in diameter consolidated cores and 1-and 2-in. in diameter unconsolidated sand packs. The cores and sand packs ranged in length from 1 to 30 ft, and they were saturated with brine and crude or refined oils. The solvents used included ethyl alcohol, isopropyl alcohol (IPA), tertiary butyl alcohol (TBAI, secondary butyl alcohol (SBA), n-amyl alcohol (NAA), methyl ethyl ketone, acetone and others. It was found that all of the oil present in a porous medium could be miscibly displaced by injecting a slug of mutual solvent and driving it with water. The oil-recovery efficiency was dependent upon (1) the relative solubilities of the solvent in oil and water, and (2) the distance traversed by the flood. For complete oil recovery from cores, a smaller amount of a preferentially oil-soluble solvent was required, compared to the amount of preferentially water-soluble solvent needed. The size of the solvent slug required varied inversely with the linear flooding-path length raised to the 0.65 power. Water-driven dual solvent combinations (an oil-soluble solvent slug followed by a water-soluble solvent slug) were found to effect complete oil recovery with less total solvent than any single solvent used. In these dual-solvent displacement experiments, the slug size required varied inversely with length raised to the 0.55 power. Based upon the experimental results, a theory was developed to describe the displacement of oil and water by mutual solvents, and equations are presented to predict the production history in a linear system. These equations take into account the properties of the solvents and the porous medium. INTRODUCTION Oil-recovery processes which utilize displacing fluids that are miscible with the reservoir fluids have been studied extensively in recent years. Because of the poor contact efficiency and high pressure requirements of the LPG-gas displacement process there has been considerable interest in the alcohol-water process, and a number of studies have been made on the recovery of oil through the use of solvents which are mutually soluble in oil and water. An investigation by Sievert, Dew and Conleyl indicated that the use of mutual solvents would be limited because the presence of water in a porous medium would cause a phase break in the leading edge of the displacing solvent. Their study also showed that, in consolidated cores containing. only oil, the displacement of oil by a water-driven mutual-solvent slug of tertiary butyl alcohol (TBA) was affected by the viscosity ratios of the fluids involved. Gatlin and slobod3 concluded that an isopropyl alcohol (IPA) slug acts as a miscible piston, completely displacing both oil and water until the alcohol content of the mixing zone falls below the concentration necessary to maintain miscibility. Their study was conducted on uniform unconsolidated sand packs. They concluded further that IPA could be used effectively to recover oil from a watered-out sand. In a paper by Taber, Gamath and Reed4 relating an investigation on sandstone cores, it was stated that the displacement of oil by mutual solvents, particularly IPA, was not a miscible displacement and that no improvement in efficiency could be expected with increase in flooding-path length. However, their analytical analysis of the displacement mechanism using TBA is, in fact, one which indicates that the displacement is controlled by miscible mixing. They suggested that the lack of improvement in efficiency with flooding - path

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory state of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which are useful for predicting machine performance and give, acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary in commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed&apos; in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted. In its first form, as stated by P. R. Rittinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include .the concept of surface energy; in this form it was precisely stated by A. M. Gaudin2 as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended. According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps, 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported&apos; that support the theory in its first form by indicating that the new surface produced in. different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work" done on. the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading since it does not follow the regular breakage pattern of most materials but is relatively harder to grind at the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory&apos; is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr/log 2.5 The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in. reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-1.5 If a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The&apos;evaluation in terms of kw-hr per net ton of 200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of -200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned, with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1952

By Ravindra M. Nadkarni, Milton E. Wadsworth

The kinetics of cetnentation of copper with iron were observed to follow first-order kinetics and increase with speed of agitation to a limiting value. Maximum rates agree closely with theoretical values based upon a model of aqueous solution diffusion through a litniting boundary film. Back reaction kinetics are shown both theoretically and experimentally to be independent of ferrous iron concentration in solution. The inlportance of attnospheres of air, oxygen, nitrogen, and hydrogen was studied and the results have been correlated with several impovtant oxidation processes involving metallic iron and copper. The kinetics of the reaction of ferric ion with metallic iron were found to be slow in the absence of metallic copper and essentially proportional to the surface area of metallic copper present in the system. THE precipitation of copper on iron is classic as an example of a relatively ancient art applied successfully for centuries with little fundamental understanding of the important parameters involved. There is some indication that the process has been a commercial means to produce copper since the sixteenth century.&apos; The amount of fundamental work on the cementation of copper with iron is not great. Wartman and Roberson2 carried out a series of detailed copper cementation experiments using natural and synthetic mine water. The following were presented as the three principal reactions: Reaction [I] is the desired cementation reaction and accordingly 0.88 lb of iron would produce 1 lb of copper. In actual practice iron consumption would more normally fall in the range of 1.5 to 2.5 lb per lb of copper. Wartman and Roberson attributed the excess consumption of iron to Reactions [2] and [3]. They found that Reactions [I] and [2] proceeded at approximately the same velocity while Reaction [3] was much slower and would be diminished by controlling the contact time. It was also pointed out that increased agitation is beneficial in removing hydrogen bubbles and barren layers of solution at the iron surface as well as removing contaminants resulting from the hydrolysis of iron. Episkoposyan3 and Episkoposyan and Kakovskii4 studied copper and silver cementation on rotating iron disks in chloride solutions. The kinetics based upon a diffusion model were first order and varied linearly with surface area and with angular velocity raised to the one-half power according to the Levich equation. The experimental activation energy for both copper and silver was approximately 3 kcal per per mole. Excess iron consumption was found to increase with temperature. The rate of cementation first increased with increasing acidity and then diminished at high acid concentrations. sutolov5 has presented an excellent review of the Leach-Precipitation-Flotation (LPF) process including a discussion of copper cementation from an electrochemical point of view although few experimental results were presented. From voltage considerations he predicted that cementation should not be influenced by the concentration of ferrous iron in solution. He considered several secondary reactions including Reactions [2] and [3] and pointed out the importance of oxidation of ferrous iron to ferric with oxygen. In addition it was suggested that Reaction [2] was enhanced by the dissolution of metallic copper by ferric iron which in turn consumed excess iron by the cementation reaction, Eq.[1]. Cementation of copper on metals other than iron has been studied by several investigators but, as in the case of iron, the amount of fundamental work is not extensive. Bashkova and kovalenko6 and Bashkova7 studied the cementation of copper on indium from copper and indium sulfate solutions. The rate was found to be first order and to increase with acidity. This was associated with a decrease in potential (EIn — ECu) and the simultaneous reduction of hydrogen ions at low pH. The rate of cementation also decreased with increasing indium concentrations which was postulated to be due to the decrease in the rate of diffusion of the ions in solution. Below 97°C the experimental activation energy was found to have the unusually low value of 2 kcal per mole and was attributed to diffusional control. Above 97°C the rate increased suddenly and was explained as a change in the rate-controlling step to a chemical reaction. In Part I of this study Nadkarni et a1 .1 have reported on preliminary results obtained in a laboratory study of the kinetics of the cementation process. The rate was found to be first order, proportional to the surface area of the iron, and to increase with speed of stirring until a maximum rate was observed. At low stirring speeds the deposit was spongy and adherent. At medium speeds the copper peeled off in bright strips and at high speeds finely divided copper was produced and continually removed from the surface. The amount of excess iron consumed increased with speed of stirring and with temperature. The average experimental activation energy combining results from several types of iron was 5.8 + 1.6 kcal per mole suggesting diffusional control through a limiting boundary film. Traditionally copper cementation has been carried out over the centuries in gravity-fed launders of various design containing scrap iron. More recently rotating drum precipitators and activated launders8&apos;10 have been used. In the latter, copper-bearing solutions are

Jan 1, 1968

By W. F. Stowasser

A downdraft traveling grate process to agglomerate pelletized iron ore concentrates has been successfully demonstrated in a pilot plant at Carrollville, Wis. Work there followed several years of development in the Allis-Chalmers Mfg. Co. laboratories, and the pilot plant phase was carried out in co-operation with Arthur G. McKee & Co., consultants and engineers to the iron and steel industry. End result of the process is conversion of iron ore concentrates into a form which can easily be transported and smelted in the blast furnace.

Jan 5, 1955

The volumes of Transactions, which are published annually, contain the list of officers, rules, etc., the Proceedings, and the papers revised for final publication. (In this revision, after the preliminary publication, authors are permitted to use the largest liberty; and the changes and additions made in papers are sometimes important. It should be borne in mind by those who study or quote a paper in the preliminary edition, that they may not have in that form the ultimate and deliberate expression of the author&apos;s views. It should be added, however, that in the majority of cases there are no important changes.) These volumes are for sale as follows, in paper covers:

Jan 1, 1917

By R. W. Kraft

A back- reflection precession-type X-yay camera for determining the crystallographic orientation of the crystallites of both phases in small areas of thick specimens of polyphase alloys is described ad the geometry, advantages, and limitations of the apparatus are discussed. Metallographic obseg-vations of interfacial angles (or habit planes or growth direction are made on the same specimen so that the crystallographic and metallographzc orientation data call be directly correlated. An example of the application of tile technique to a unidi-~~ectionally solidified CuA12-A1 eutectic specimen is presented. The interfacial planes ad growth directions of each phase were established, and the orientation relationship between the phases was observed and found to be approximately intermediate between two previously reported relationships. The crystallographic interfacial relationship between two solid phases is an important parameter in a variety of metallurgical phenomena because of the energy associated with the interface and because this energy is at least partly associated with the way in which the two space lattices are in contact along the interface. In order to describe the interfacial planes in the crystallites of both phases it is necessary to determine the crystallographic orientation of each phase in a specimen relative to each other, and to directly correlate these data with met-allographic measurements from which the interfacial planes can be determined on the same specimen. The back-reflection Laue technique is the easiest way to determine the orientation of thick single crystals or large grains and the method can be combined with metallographic techniques to provide the necessary data, provided the reflections from each phase can be distinguished from one another. However, if the crystallites are small or of varying orientation or if one or both phases has a unit cell with less than the maximum symmetry, many overlapping and complex Laue patterns are recorded simultaneously and it becomes impractical if not impossible to interpret the photographs. All of these complexities were present in a unidirectionally so- lidified A1-CuA12 eutectic alloy1 for which a crystallographic analysis was desired. Consequently the method described here was developed since no known X-ray or electron diffraction technique had all of the following attributes which were required. 1) Method should yield data from which the crys-tallographic orientation of every crystallite or diffracting unit in the irradiated area can be determined. 2) Method should be adaptable to the study of small areas. Depending upon the degree of preferred orientation in the specimens, it should be possible to obtain reliable data in a reasonable length of time on irradiated areas as small as 1.0 or even 0.1 mm in diam. 3) Method should permit direct correlation of crystallographic data with microscopic orientation data pertaining to crystallite axes, habit, morphology, and growth directions as determined by optical microscopy. 4) method should be such that selected areas of large specimens can be easily studied. Trepanning of a small specimen (such as an electron microscope specimen) from larger specimens was undesirable since it would greatly increase the problem of correlating the crystallographic and microscopic directional data. Requirements 3 and 4 dictated that an X-ray back-reflection pinhole technique should be used on large samples, such as metallographic specimens which had previously been examined and analyzed for their microscopic characteristics. Similarly, requirement 2 could be satisfied by choosing a collimator of appropriately small diameter. Exposure times would not be excessive provided the detector were close enough to the specimen. Because of space limitations film was chosen in preference to a Geiger counter. Requirement 1 was fulfilled by using monochromatic radiation and providing enough additional degrees of freedom in specimen rotation to compensate for Bragg law restrictions on diffracted beams. DESCRIPTION OF APPARATUS The apparatus shown in Fig. 1 consists of a pin-hole collimator, (a), projecting through a rotatable circular film in a holder, (b), which records X-ray reflections in the back-reflection region. The specimen, (c), is mounted on the end of a shaft, (d), which is provided with an adjustment, (e), so that the specimen surface can be placed accurately on

Jan 1, 1962

By Francis Clark

WHEN 60:40 brass is heated to 825° C., given a drastic quench to obtain the beta solid solution, and reheated, various changes take place in the structure. Reheating at 200° C. causes a fine, granular, sorbitic structure to appear which has been considered alpha solid solution. These particles coalesce at higher temperatures of reheating, and at 470° C., the alpha forms twins. A further study of these transformations was considered worth investigating. EXPERIMENTAL WORK The object of the experimental work was to study the effect of mechanical work on rolled 60:40 brass, quenched and reheated, and the mechanism of twinning in the alpha reeds of a furnace-cooled specimen. It was desired to determine the effect of mechanical work on the transformations taking place on reheating the quenched material, both at 200 and at 470° C. A study of the nature of the structure resulting from the breakdown of the beta at 200° C. and a study of the mechanism of twinning above 470° C. were considered problems for investigation. The question of the twinning of the alpha reeds was also an important phase of the work. With high-power magnifications, there was hope of following these processes.

Jan 1, 1927