Search Documents

By C. F. Smart

SINCE their comparatively recent development, the alloys of cadmium with silver and copper or nickel, and of cadmium with nickel alone, have been used somewhat extensively as liners for connecting rod bearings and main bearings of internal-combustion engines. In applications where, owing to high hearing loads and elevated operating temperatures, the life of hearings made from tin-hale or lead-base alloys has been undesirably short, cadmium alloys have demonstrated considerable advantage. In applications where, because of deflection of the crankshaft or bearing supports, copper-lead bearing metals have resulted in scored shafts, cadmium alloys have been operated successfully. The somewhat serious drawback to these alloys in hearing service has been that they, in common with copper-lead and certain lead alloys, are susceptible to corrosion in the presence of lubricants containing organic acids. These acids may be fatty acids (such as oleic acid) derived from animal or vegetable oils that sometimes have been compounded with engine lubricants, or they may be compounds of an acid nature developed by the oxidation of some petroleum oils under operating conditions. The result of such acid attack on hearings is illustrated by the photograph, Fig. 1. The petroleum oils that are most readily oxidized to a corrosive condition, and the operating conditions under which such oxidation most readily occurs, are now rather well known among the technical organizations of both the petroleum and automotive industries. While means have been developed for inhibiting petroleum oils against such acid formation, the knowledge that this condition may be encountered has been a factor in restricting the wider use of cadmium alloys as engine bearings. It has appeared, therefore, that their value and use would be enhanced if they could be made corrosion-resistant to a degree compatible with the most severe operating requirements. Investigation, undertaken with this in view, indicated that the addition of fractional percentages of the metal indium to the cadmium bearing

Jan 1, 1938

By D. J. McAdam

In 1917 Haighl presented evidence that under simultaneous corrosion and cyclic stress metals may fail at lower stresses than if the corrosion is prior to the cyclic stress. In 1926 the author, while investigating the cooling effect of water on the fatigue resistance of metals, found that under these conditions steel specimens fail at stresses far below the endurance limit.2 (By "endurance limit" is here meant the fatigue limit obtained with specimens as free as possible from stress concentration and corrosive influences.) This led to an investigation (at the Naval Engineering Experiment Station, Annapolis, Md.) of the influence of cyclic stress on corrosion. This investigation may be divided into three parts. The first part was a general survey of the conditions necessary to cause complete failure under corrosion and cyclic stress of relatively high frequency. The entire process by which metals fail under these conditions was called LLcorrosion-fatigue." Corrosion-fatigue limits" for a large number of metals were determined and the relationships of these limits to chemical composition, heat treatment and physical properties were established. The conclusion was reached that corrosion-fatigue is due to the accelerating influence of cyclic stress on corrosion. Results of this part of the investigation were presented in five papers.*-= The second part of the investigation was a preliminary study of the influence of cyclic stress on corrosion. Each experiment was conducted in two stages. The first was a corrosion stage in which the specimen was corroded under cyclic stress; the second was a fatigue stage, in which the previously corroded specimen was tested (without further corrosion) to determine its fatigue limit. The difference between this fatigue limit and the endurance limit was used as a criterion of the "damage" due to

Jan 1, 1932

By Clifford Wilson

SCREENED pipe is designed with the view of restraining the fine, free-running sands of the production zone from entering oil wells. Its successful use is dependent on a number of factors. The nature and effects of some of these factors can be determined through experiment and observation, but some of the elements that have a distinct bearing on the use of screened pipe can be evaluated only by estimate. The important subsurface conditions which affect the use of screened pipe are: 1. Depth of production zone. 2. Extent of production zone. 3. Reservoir pressure. 4. Character and relative quantity of oil and gas. 5. Character of sediments a. Consolidation of beds. b. Variation in beds. c. Grain-size gradation of sands. d. Free-running characteristics of sand from different levels. Aside from the use. of mechanical equipment and tools, the measures to be taken in the installation of screened pipe involve: 1. Size of liner. 2. Length of liner. 3. Design and mesh of screen. 4. Portion of liner to be screened. 5. Manner of setting liner. 6. Preparation of or washing of the well before or during the setting of the screen. 7. Manner of bringing in the well. 8. Manner of flowing the well. Values applicable to the actual subsurface conditions that exist at any well can only be approximated. The accuracy of the estimate will be measured by the amount and quality of the evidence at hand and the personal factor of ability to interpret the evidence fairly, whether

Jan 1, 1932

NORTH AMERICA Number Members Alaska 36 Canada 323 Mexico 184 Newfoundland 3 United States Alabama 40 Arizona 111 Arkansas 8 California 646 Colorado 171 Connecticut 90 Delaware 21 District of Columbia 136 Florida 16 Georgia 7 Idaho 66 Illinois 208 Indiana 66 Iowa 11 Kansas 24 Kentucky 32

Jan 1, 1934

By W. G. Fischer

Basic laboratory tests on trona and the surrounding shales initiated the Rock Mechanics program. The stress-strain curve, modulus of elasticity, Poisson's ratio, the uniaxial rock strength, Mohr's envelope, the biaxial stresses at failure, and creep were investigated. A series of underground problems were then approached using this information and various field measuring devices, most of which were developed by the Bureau of Mines. Initially, stress concentrations near mine openings were evaluated using the stress relief technique. This required an accurate determination of the pre-mining stress field. Later, stress concentrations associated with the cave line were studied. After about 30 stress reliefs over an appropriate time interval the effects of one type of mining could be compared against another. The microseismic technique was used to investi- gate a possible application of warning devices near the cave line. A study of mine reorientation was made. Problems related to the shape and size of pillars and barriers were studied. The effectiveness of roof bolting patterns was examined. Control of roof stresses was attempted. A new system of mining in heavy ground has been developed using the information secured in the Rock Mechanics program. Without this system, mining in more than one instance would have been next to impossible. Indeed, from this one discovery alone, the Rock Mechanics program has paid off in improved safety as well as in dollars. The Westvaco trona* mine is located near the town of Green River in the southwestern corner of Wyoming. It is owned and operated by FMC Corp. on land leased from the US Government, the State of Wyoming, and the Union Pacific Railroad. A conventional room and pillar system is being used, (Fig. 1) with complete removal of the pillars during final mining. Return air bleeders surround

Jan 1, 1964

By O. W. Ellis

The question of the influence of gases upon the properties of copper has received the attention of a number of investigators, among whom Sieverts,' Iwase,2 Lobley and Jepson3 stand preeminent. Solubility of Gases in Copper Sieverts and Iwasé concerned themselves with the solubility of a variety of gases in the metal in the solid and liquid states. They determined the absorption coefficients of these gases and in all cases found a sharp change in solubility at the melting point of the metal. In this respect they disagree with Lobley and Jepson, who have based their opinions upon the appearance of small ingots of the metal which had been fused in an atmosphere of one or other of three gases and had then been rapidly cooled, while surrounded by gas, to the freezing point (rate—possibly 30" to 60" C. per sec.). The ingots that had been fused and cooled under nitrogen and carbon monoxide were free from blowholes and it was assumed that these gases were not absorbed in amounts much in excess of those which would dissolve in the solid metal; the ingots similarly treated under hydrogen were full of blowholes and it was assumed in this case that gas was ejected on solidification of the copper. The effect of varying the rate of freezing upon the character of the test ingots was not examined by these investigators; otherwise, it is felt, their views might have been subject to modification. Sieverts' most important contribution is that the solubility of a gas in any metal is proportional to the square root of its pressure or concentration. Knowing then the absorption coefficients of the various gases in copper, it should be possible to determine the analysis of the

Jan 1, 1929

By O. W. Ellis

The question of the influence of gases upon the properties of copper has received the attention of a number of investigators, among whom Sieverts,' Iwase,2 Lobley and Jepson3 stand preeminent. Solubility of Gases in Copper Sieverts and Iwasé concerned themselves with the solubility of a variety of gases in the metal in the solid and liquid states. They determined the absorption coefficients of these gases and in all cases found a sharp change in solubility at the melting point of the metal. In this respect they disagree with Lobley and Jepson, who have based their opinions upon the appearance of small ingots of the metal which had been fused in an atmosphere of one or other of three gases and had then been rapidly cooled, while surrounded by gas, to the freezing point (rate—possibly 30" to 60" C. per sec.). The ingots that had been fused and cooled under nitrogen and carbon monoxide were free from blowholes and it was assumed that these gases were not absorbed in amounts much in excess of those which would dissolve in the solid metal; the ingots similarly treated under hydrogen were full of blowholes and it was assumed in this case that gas was ejected on solidification of the copper. The effect of varying the rate of freezing upon the character of the test ingots was not examined by these investigators; otherwise, it is felt, their views might have been subject to modification. Sieverts' most important contribution is that the solubility of a gas in any metal is proportional to the square root of its pressure or concentration. Knowing then the absorption coefficients of the various gases in copper, it should be possible to determine the analysis of the

Jan 1, 1929

By Harry E. Cross

Kiln Products commissioned a Waelz kiln 4 metres in diameter by 75 metres long, in South West Africa in March, 1969, to recover nine in a form suitable for the production of electrolytic zinc. The raw material consists of a mixture of zinc silicate concentrates and zinc rich tailings purchased from an adjacent zinc mine - the mixture containing 20% to 25% zinc. The chemical composition of the ore is tabulated and the initial test results are described. Due to the comparatively low temperature at which the ore starts softening the kiln has certain unusual features to enable the temperature to be controlled within the necessary limits. A detailed description of the kiln, the starting-up problems and present operating conditions and results are presented.

Jan 1, 1970

By Milo Krejci

(Butte Meeting, August, 1913.) THE plant and quarries of the Inland Portland Cement Co. are located at Metaline Falls, Wash., about 128 miles north of Spokane, on the Pend Oreille river, and within 10 miles of the Canadian border. The plant is one of a chain of cement plants controlled by the Lehigh Portland Cement Co., of Allentown, Pa. Work on this plant was commenced in June, 1910, and was completed in April, 1911, but on account of some delays in 'the construction of the power plant, the works were not put into operation until August, 1911. Since then it has been in continuous operation and has furnished the Inland Empire with a high grade of cement. Fig. I is a view and Fig. 2 is a plan of the works. Water Power Development.-The source of the water supply for the hydro-electric plant of the Inland Portland Cement Co. is Sullivan lake, a body of water approximately 5.5 miles long and 0.5 mile wide, situated in the Kaniksu Forest Reserve. A wooden crib dam was installed so as to raise the elevation of the lake 25 ft., and the additional storage capacity was taken up by the diversion of Sullivan creek into the lake by means of a wooden flume, 0.25 mile long, 6 by S ft. in cross-section, and a ditch 1,200 ft. long. The water from the lake follows the natural water course to an intermediate storage reservoir, which was created by the construction of an earthen dam. This pond wits used in connection with the saw mill which was installed at this point. Besides the earth dam, there was also built a crib, at the point shown in the sketch map, Fig. 3. This crib dam is 35 ft. high. From this point the excess water follows the natural course of Sullivan creek to the Pend Oreille river.

Jan 7, 1913

By Thomas E. Ban, Charles D. Thompson, Charles A. Czako

Continuous sintering-a metallurgical process for more than 50 years-has broadened from its origin in nonferrous metallurgy to present-day applications in ferrous, chemical, and nonmetallic fields. During the past year, self-fluxing sinter production has been a subject of active interest to iron metallurgists in North America. Accomplishments however, have come predominantly from Europe and proper interpretation of these reports requires an understanding of European raw materials and European economics. The technology, of course, can be applied universally.

Jan 10, 1959

By Wayne E. Glenn, R. W. French, Lincoln F. Elkins

The Lance Creek Sundance reservoir provides a case history of ro years performance of a reservoir in which unit operation has permitted effective utilization of gravity drainage augmented by primary pressure control with injection of gas into top structural wells. Detailed performance of the reservoir is presented by means of maps of Well status, reservoir pressure, individual well recovery, etc., and by pool-performance charts. Analysis of reservoir performance indicates only minor water encroachment, so that gravity, injected gas, and expansion of gas are the main oil-expulsive agents. A simplified theory of regional drainage of oil from upstructure location to downstructure location due to gravity is presented and checked by means of comparison of "reservoir" permeability and "well" permeability from the pool performance. Good order of magnitude agreement was obtained. Individual well performance and overall reservoir performance indicate possibility that maintenance of pressure makes ineffective those parts of the reservoir in which permeability is too low to permit effective drainage of oil by action of gravity. Oil from these parts can be recovered only when pressure is reduced locally by selective withdrawal or when overall reservoir pressure is finally reduced.

Jan 1, 1949

By Alden Greninger

METALLURGISTS have long believed that martensite in steel forms as plates along the octahedral {111} planes of austenite. Much has been written about mechanisms whereby units of the austenite lattice are pictured as transforming to martensite by shearing movements initiated along the octahedral planes of austenite, supposedly resulting in plates of martensite lying parallel to these planes of shear. A critical inspection of two or three photomicrographs of quenched hypereutectoid steel led us to the conclusion that the orientation habit of martensite, at least in hypereutectoid austenite, could not possibly be octahedral. Inasmuch as recent studies30,31 of the martensite-type reaction in nonferrous alloy systems have established the irrational orientation habit as characteristic of this type of lattice transformation, the need for a thorough restudy of the crystallography of martensite formation in steel was evident. The present paper reports the results of such a study, extended to include both cementite and some of the products of constant-temperature decomposition of austenite. Also reported are a few of the results obtained from a microscopic and X-ray study of the austempering process in very high-carbon steel.

Jan 1, 1940

By E. A. Gulbransen, W. S. Wysong

THE behavior of tungsten and its surface oxides in oxidizing and reducing atmospheres and in high vacua at elevated temperatures is a question of considerable technical importance. The use of tungsten as a metal or as an important component in alloys in high temperature oxidizing atmospheres has been limited because of the unprotective nature of its oxide film and the volatility of its oxide. This paper will present results of a microbalance study1,2 of the following problems: (I) the oxidation behavior in the temperature range of 25 to 550°C (2) the reduction with pure hydrogen of thin oxide films formed on tungsten, and (3) the volatility of thin oxide films on tungsten. Tungsten is an interesting metal to study for the following reasons: (1) although the oxide to metal volume ratio is greater than one, the oxide is not considered protective, (2) the metal readily oxidizes at temperatures from 300° to 550°C (3) the oxides W02 and WO3 are reduced at temperatures as low as 500°C. by hydrogen, and (4) the oxide W02 is volatile at temperatures from 800 to 1100°C. LITERATURE The oxidation of tungsten in its thin film range has not been studied critically. In the thick film range Dunn3 has made the only systematic study. He found the oxidation rate to obey the parabolic rate law in the temperature range of 700 to 900°C. The temperature variation of the oxidation rate constant was found to follow an exponential law of the Arrhenius type. An inflection was noticed in the temperature plot of the rate law constant at 850 to 900°C. This was attributed to a phase change in the oxides. Scheil4 has studied the oxidation rate at 500 and 700°C over long periods of time and found a linear rate law. This result was interpreted as evidence for the presence of a nonprotective film. Pilling and Bedworth5 analyses of the oxide volume to metal volume ratio would indicate that a compact protective film should form. McAdam and Geil6 have studied the oxidation of tungsten in the thin film range using the interference color method. A parabolic rate law was found. Their curves showed that tungsten oxidizes faster than nickel but more slowly than iron. The lattice structures found in the oxidation of tungsten surfaces have been studied by Hickman and Gulbransen.7 They have reported that W03 is the stable oxide in contact with the metallic substrate up to approximately 600°C while W02 forms first at 700°C. Hägg and Magneli8 have recently reported a study of the lattice structures observed in the tungsten oxides using the X-ray diffraction method. In addition to an a-phase W03 and a d-phase W02, they reported the existence of two new phases. A ß' phase, homogeneous between

Jan 1, 1947

By Marcus A. Grossmann

This paper offers for consideration certain somewhat radical modifications in the iron-carbon diagram, these modifications being the result of the presence of notable amounts of alloying elements. When only small amounts of alloys are present, the standard iron-carbon diagram (Fig. 1) can be used with but insignificant changes; when larger amounts of alloys are present, however, it assumes a distinctly altered appearance. No comment is offered for the present except to call attention to the delta area, A4BM, which represents a region of mixtures of austenite and delta iron, just as area A3SP represents mixtures of austenite and alpha iron. Absence of Carbon We may turn at once to the effect of the presence of alloys. It has been found that in the complete absence of carbon, the gamma change will sometimes disappear entirely when sufficient alloying element is

Jan 1, 1927

By A. F. Taggart

THE following notes represent significant excerpts from a mass of records of experimental work done in the ore-dressing laboratory at the Columbia School of Mines during the years 1926 to 1928-inclusive. CLASSIFICATION OF EXPERIMENTAL WORK The experiments performed may be grouped for purposes of description under the following general -headings: I. Collecting agents. a. A method for quantifying collecting effect. b. Coating with undissolved collecting agents (oils) c. Action of dissolved collecting agents. II. Frothing agents. a. A method for quantifying frothing effect. b. Relation between frothing effect and chemical composition. III. Inorganic reagents. a. Methods of studying the effects of these reagents. b. Effect on slime dispersion. c. Effect on sulfides. SUMMARY OF THE ORIGINS OF PRESENT-DAY FLOTATION PRACTICE The first practicable, foolproof method of froth flotation was described in U. S. patent 835120, issued in 1906 to Sulman, Picard and Ballot, and in the equivalent patents in other countries. A number of less simple methods of producing the same result had been described previously in patent publications and otherwise.1 The reagents specified in all of these early patents were "oils" and, in addition, some inorganic substance, usually an acid. The quantities of reagents recommended and added were enormous when' compared with those used today.

Jan 1, 1929

By James P. Kimball

Sulphur is always present in mineral coal of every variety. In the oxidized state it may exist as sulphuric acid in combination with a base. In the unoxidized state it exists in combination with iron as bisulphide of iron. It is also supposed by some chemists to exist in unknown combinations with the organic elements of the coal. This supposition requires the demonstration as a fact that certain coals yield more sulphur than what may exist in a free state, or what belongs to recognized combinations, not only with the accompanying iron but with other inorganic bases abundantly occurring in coals, but which unfortunately are very rarely estimated. This practically as well as theoretically important question it is at present impossible to decide, simply for want of available thorough ultimate coal analyses including the ash. Such analyses, at the best imperfect, are luborious and intricate, and therefore seldom made, the much simpler proximate analyses, so-called, being resorted to by most chemists for technical purposes, and commonly substituted for more scientific work even in the laboratories of government surveys. And it is unfortunate enough that few ultimate analyses are extended to the composition of the ash, much less to its relation to the original constitution of the coal. Sulphur chiefly occurs in most coals in the form of yellow pyrites (pyrite) and white pyrites (marcasite), both minerals, characterized by differences in crystalline form and in physical properties as well as in color, but having the same chemical composition (FeS2). No coal is entirely free from one or both of these dimorphous forms of bisulphide of iron. It may be disseminated through the mass so as to be invisible, in plates or scales between the laminæ of the coal, or in conspicuous segregations or nodules, sometimes of considerable dimensions. Coals greatly differ as to the proportion of sulphur which they contain. They also differ as to the relative proportion in which its several forms of combination occur. Such qualitative and qnantitative disparities arc scarcely, if at all, more marked in separate coal seams of a uniform type than in different parts of one and the same coal seam, whether it be considered locally as constituted of several

Jan 1, 1880

By S. L. Hoyt

IN technological studies on steel considerable emphasis has been placed on the identification of the foreign inclusions, testimony of which is adequately given in the metallographic literature covering methods for their identification. The outstanding accomplishment in this field is the scheme devised by Campbell, Comstock and Wohrman for identi-fying various oxides, sulfides, silicates and other constituents by syste-matic etching tests and microscopic examination.1 The time involved in carrying out this procedure has led to attempts to secure quicker methods, or at least to shorten the time required to secure essential information. An example of this is the use of dark field illumination, but when this was tried out by the authors it was found that cavities and pits on the polished surface appeared bright on a dark field and could not be distinguished from small glassy inclusions. Still another means is the Leitz Ultropak, an instrument equipped with optical units for the illumination of the specimen by reflected light to secure an effect similar to dark field illumination. The structures are made visible in exceedingly sharp details by utilizing the inherent properties of the samples, such as refractive index, absorption coefficients and reflection powers. We have had no experience, with the Ultropak, but a recent paper by Benedicks and Löfquist3 describes methods for

Jan 1, 1934

By F. Lynwood Garrison

It is not intended to make in the present paper any deduction or to formulate any theories from the results obtained by experiments. The further expenditure of considerable time and labor would be required to obtain a sufficient basis for positive assertions as to the microscopic structure of the different varieties of iron and steel, and the structural changes which take place in them. It is therefore my purpose at this time to offer simply a synopsis of the general results arrived at in a few months' work, a brief description of apparatus used, and a few hints as to the preparation and preservation of the material which it is intended to investigate. The study of the microscopic structure of iron and steel is not altogether new. Some attention has been given it in both England and Germany. But the foreign publications on the subject have thus far been confined, so far as I am aware, to two papers, one by Herr Martens, of Berlin, contributed to the Verein zur Befoerderuny des Gewerbfleisses and the other a lecture by Dr. H. C. Sorby of Sheffield. Dr. Sorby, it seems, was induced to investigate the subject as bearing on the structure of meteoric iron ; and the results he obtained are certainly very interesting. At the Boston meeting of this Institute, in February, 1883, Mr. J. C, Bayles called attention to the subject in a neat and exceedingly interesting paper, in which the work of Messrs. Martens and Sorby was summarized,* and original suggestions were added. It is at present difficult to say what will he eventually the practical value of the microscope, thus employed, in the sciences of engineering. The role which it seems most likely to play is that of' an adjunct to the testing-machine, and not (as some have supposed) a rival to the chemical laboratory. That it will be a most valuable accessory seems, to say the least, highly probable. I need hardly go at length into the details of preparing the material for examination. Mr. Bayles has described the process in such a plain and comprehensive manner that if his instructions are

Jan 1, 1886

By S. Fróes Abreu

The importation of liquid fuels in Brazil amounts to about 1,300,000 tons; 30 per cent of this total being gasoline for automobiles and airplanes. Statistics show an increasing consumption of gasoline notwithstanding the use, daily greater, of fuel alcohol, a domestic fuel of low cost in the producing areas. The Brazilian market for petroleum products has shown a tendency to grow as the country has steadily developed— expansion of the industries in the areas already developed, and also the recent occupation and population of new zones. The war has brought many difficulties to Brazil. It has limited the importation of petroleum products, which came mostly from the United States, Venezuela and Mexico. During the first days of the present crisis automobile and truck traffic was vastly curtailed; but the national activity in the production of more fuel alcohol, and principally in the development of producer gas, has done much to provide a solution for the transportation crisis threatened at the beginning of the gasoline shortage. Many thousands of cars and trucks in Brazil are now burning producer gas made from charcoal. Producer gas for automobiles has been improved by Brazilian engineers and many new types have appeared. - Production There is only one producing oil field in Brazil—the one in the State of Baia, near the Baia de Todos os Santos. The first producing oil well was drilled in Lobato in 1939 by the Federal Government following studies carried on in that area by Oscar Cordeiro, S. Froes Abreu, G. Paiva and J. Amarai. The field and laboratory work done by these men was published in 1936 in a paper entitled " ContribuicBes para a Geologiado Petroleo no Reconcavo (Baia)," which indicated the potentialities of the area as an oil producer. After the discovery of the first producing well, the Brazilian Government issued a decree establishing an area, 60 km. in radius, as a National Reservation. This first well was drilled in Lobato. In no other locality in Brazil is any petroleum produced. Although many wells have been drilled in the southern part of Brazil, on the northeastern coast and in the Amazon Basin, they yield nothing. Actual production is below 1000 bbl. daily. The producing area covers Itaparica Island, Candeias and Arath, Joanes Island and Lobato. Since very little geological information was available, especially about subsurface structure, it was necessary to drill several wildcats in order to collect the data essential in the choosing of good locations. The United Geophysical Co. was contracted to perform a geophysical survey to clear up the major problems concerning the oil deposits in the Reconcavo beds. The best wells in Reconcavo are on Itaparica Island, where the daily flow amounts to about zoo bbl.; in other sectors production is considerably lower and most of the wells are pumping. In the Aratfi sector, near an area of very light oil, there is an important gas field, with wells producing about I0,000,000 cu. ft. daily.

Jan 1, 1944

By S. Fróes Abreu

The importation of liquid fuels in Brazil amounts to about 1,300,000 tons; 30 per cent of this total being gasoline for automobiles and airplanes. Statistics show an increasing consumption of gasoline notwithstanding the use, daily greater, of fuel alcohol, a domestic fuel of low cost in the producing areas. The Brazilian market for petroleum products has shown a tendency to grow as the country has steadily developed— expansion of the industries in the areas already developed, and also the recent occupation and population of new zones. The war has brought many difficulties to Brazil. It has limited the importation of petroleum products, which came mostly from the United States, Venezuela and Mexico. During the first days of the present crisis automobile and truck traffic was vastly curtailed; but the national activity in the production of more fuel alcohol, and principally in the development of producer gas, has done much to provide a solution for the transportation crisis threatened at the beginning of the gasoline shortage. Many thousands of cars and trucks in Brazil are now burning producer gas made from charcoal. Producer gas for automobiles has been improved by Brazilian engineers and many new types have appeared. - Production There is only one producing oil field in Brazil—the one in the State of Baia, near the Baia de Todos os Santos. The first producing oil well was drilled in Lobato in 1939 by the Federal Government following studies carried on in that area by Oscar Cordeiro, S. Froes Abreu, G. Paiva and J. Amarai. The field and laboratory work done by these men was published in 1936 in a paper entitled " ContribuicBes para a Geologiado Petroleo no Reconcavo (Baia)," which indicated the potentialities of the area as an oil producer. After the discovery of the first producing well, the Brazilian Government issued a decree establishing an area, 60 km. in radius, as a National Reservation. This first well was drilled in Lobato. In no other locality in Brazil is any petroleum produced. Although many wells have been drilled in the southern part of Brazil, on the northeastern coast and in the Amazon Basin, they yield nothing. Actual production is below 1000 bbl. daily. The producing area covers Itaparica Island, Candeias and Arath, Joanes Island and Lobato. Since very little geological information was available, especially about subsurface structure, it was necessary to drill several wildcats in order to collect the data essential in the choosing of good locations. The United Geophysical Co. was contracted to perform a geophysical survey to clear up the major problems concerning the oil deposits in the Reconcavo beds. The best wells in Reconcavo are on Itaparica Island, where the daily flow amounts to about zoo bbl.; in other sectors production is considerably lower and most of the wells are pumping. In the Aratfi sector, near an area of very light oil, there is an important gas field, with wells producing about I0,000,000 cu. ft. daily.

Jan 1, 1944