Search Documents

By T. D. Yensen

It is safe to say that of all the different materials that go to make up electrical machinery, iron is the most important. Upon its magnetic and electrical quality depends not only the efficiency of the machine but, to a very large extent, the cost. Aside from the mechanical strength, there are three characteristics of iron that are of importance in this connection, viz., magnetic hysteresis, electrical resistance, and magnetic permeability. In the homopolar machine, where the magnetic flux is unidirectional, permeability is the only important factor, but in all other machines the flux is reversed in one or more parts and causes losses due to hysteresis and eddy currents. The eddy-current loss depends largely upon the electrical resistance of the iron; the higher the resistance the lower the loss, under otherwise identical conditions. These hysteresis and eddy-current losses cause heating of the machine, and as they depend upon the magnetic density in the iron, this density must be regulated so that the heating shall not be excessive. If the hysteresis and eddy-current losses and the permeability of the magnetic circuit will permit an increase in the magnetic density, or, in other words, a decrease in the amount of iron, this in turn will mean a decrease in the amount of copper needed, with a consequent decrease in the copper loss. It is thus seen that, indirectly as well as directly, the above characteristics have an important bearing on both the efficiency and the cost of electrical machinery. In general, it may be said that iron for electrical machinery should have the following characteristics: (1) low hysteresis loss, (2) high electrical resistance, and (3) high permeability. These are the characteristics that investigators have been striving to attain since electrical machinery first came into use. Until the beginning of the present century, Swedish charcoal iron was regarded as the best grade of iron for magnetic purposes, and even now it ranks high among the various grades used. About that time Sir Robert Hadfield1 produced a number of iron alloys that revolution-

Jan 1, 1916

By Oscar A. Glaeser

It is common knowledge that the iron orebodies of the Mesabi Range lie nearly horizontal and are of trough or blanketlike types. These orebodies are from a few feet to several hundred feet thick and vary from a few acres in extent to the size of the largest one, at Hibbing, Minn., which is over 1 mile wide and 3 miles long. They are covered with sand, boulder and clay overburden and occasionally shallow depths of ledge material, varying in total depth from about 20 to 200 ft. Large areas are not capped with overlying ledge material; the top of the ore lies directly underneath the surface material. Because of the comparatively great tonnage of ore, open-pit mining has made tremendous strides since the first open-pit ore was shipped from this range by the Merritt brothers, from the Mountain iron mine in October, 1892, and along with the great development of open-pit mining on the Mesabi Range has gone a tremendous change in the character of. equipment used. Early Stripping Operations The first stripping at the Burt mine at Hibbing, Minn., started in 1902. The engineers spent a long time in selecting the most suitable location for a small pit area, involving a stripping contract of 350,000 cu. yd. This property afterwards had several million yards of stripping and several million tons of ore removed from it, but inasmuch as it was the first open pit of the Oliver Iron Mining Co. in this district it was necessary to try several different locations for the small pit area, to uncover maximum tonnage and the best grade of ore so as to sell the idea of open-pit mining and discontinue the underground operation then going on. The writer's first open-pit work on the Mesabi Range was in 1903 as an Oliver company mining engineer on a stripping job of 1,500,000 cu. yd. at the Monroe mine, Chisholm, Minn. Here the contractor, an old-timer used to railroad methods, was, to a small extent, using teams of horses hitched to 2-yd. narrow-gage cars and hauling the stripping material from the pit area to outside of the pit limits. The dirt thus moved was loaded by hand. The same contractor was also using 60-ton and 70-ton railroad-type shovels with dippers of 21/2 and

Jan 1, 1930

By HAROLD VINTON COES

THE motive for merging or consolidation today is conspicuously different from that actuating business men in the late eighties and early nine- ties. Then they combined to secure added productive capacity and to monopolize their respective industries with a view to exploiting the consumer. So flagrant were some of these cases that they brought about their own correctives via retaliation on the part of the public and the subsequent restrictive legislation and legal curbs. The objective of the present-day merger, writes W. R. Hill in Printers' Ink, December, 1927, is summarized as follows : "In the golden days when an industry was being cut to pieces, the prevailing cure was to combine. The reason for such trusts was to strangle competition and by creating a monopoly, dominate the market, raise prices, regardless of economic business methods, and simply force larger profits.

Jan 1, 1930

By Walter Harvey Weed

CONTENTS. [ ] INTRODUCTION. THIS paper deals with certain ore-deposits whose structural features or mineral contents (or both) result, directly or indirectly, from igneous intrusions and their after-effects. It is largely a discussion of contact metamorphic ore-deposits based upon the physical changes in rocks due to contact action. It involves a classification of ore-deposits only so far as is abso-

Jan 1, 1913

By Haydn H. Murray, Sam H. Patterson

The term clay is somewhat ambiguous unless specifically defined, because it is used in three ways: (1) as a diverse group of fine-grained minerals, (2) as a rock term, and (3) as a particle-size term. Actually, most persons using the term clay realize that it has several meanings, and in most instances they define it. As a rock term, clay is difficult to define because of the wide variety of materials that compose it; therefore, the definition must be general. Clay is a natural earthy, fine-grained material composed largely of a group of crystalline minerals known as the clay minerals. These minerals are hydrous silicates composed mainly of silica, alumina, and water. Several of these minerals also contain appreciable quantities of iron, alkalies, and alkaline earths. Many definitions state that a clay is plastic when wet. Most clay materials do have this property, but some clays are not plastic; for example, halloysite and flint clay. As a particle-size term, clay is used for the category that includes the smallest particles. The maximum-size particles in the clay-size grade are defined differently on various grade scales. Soil investigators and mineralogists generally use 2 micrometers as the maximum size, whereas the widely used scale by Wentworth (1922) defines clay as material finer than approximately 4 micrometers. Some authorities find it convenient to use the term clay for any fine-grained, natural, earthy, argillaceous material (Grim, 1968). When used this way, the term includes clay, shale, or argillite, and some argillaceous soils. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, the term is generally understood by those who use it. Clay is an abundant natural raw material, and it has an amazing variety of uses and properties which will be discussed in this chapter. Clays rank among the leading industrial minerals in both tonnages produced and total value. Their importance is indicated in Table 1, which lists the 1978, 1979, and 1980 production and values according to the US Bureau of Mines (Ampian, 1980). Statistical data summarizing world production of kaolin, bentonite, and fuller's earth are compiled by the US Bureau of Mines (Ampian and Polk, 1981). The total world bentonite production in 1980 was 6,625,204 st of which the United States produced 4,184,619 st. The total fuller's earth produced in the world in 1980 was 1,952,600 st of which 1,534,000 st was produced in the United States. The total world kaolin production in 1980 was estimated at 22,971,000 st. Approximately 13 million tons of this total was produced in two countries, the United States and the United Kingdom. World production data on ball clay, fire clay, and miscellaneous clays are not available. As industrial minerals, clays are a complex group that consists of several mineral commodities, each having somewhat different mineralogy, geologic occurrence, technology, and uses. In this chapter these commodities are organized as follows: (1) bentonite and fuller's earth; (2) kaolin, ball clay, halloysite, and refractory clays; and (3) miscellaneous clay and shale. Bentonite and fuller's earth are grouped together because they are closely interrelated. Though bentonite is a term based on mineral composition and fuller's earth is a term based on use, the two are virtually inseparable, because much, but by no means all, clay sold as

Jan 1, 1983

By J. H. Nead, T. S. Washburn

The grades of commercial steel produced in large quantities can be divided into two general types from the standpoint of ingot structure— killed and rimmed. Killed steel covers a wide variety with carbon contents throughout the range of the steel portion of the iron-carbon diagram, and is the kind usually used in the production of alloy steels. Rimmed steel is normally associated with carbon ranges under 0.30 per cent, and is not yet used to a large extent in alloy practice, except for copper-bearing steels. The fundamental differences in the ingots made from these two types of steel can be seen most easily in Figs. 1 to 7. In the rimmed ingot shown in Figs. 5 to 7 there are two lines of blowholes approximately parallel to the sides and coming together at the top and at the bottom of the ingot. In the killed ingots shown in Figs. 1 to 4 these blowholes arc not present. Also, the rimmed ingot has no well defined pipe, as compared to the deep pipe on the killed ingots, and there are numerous primary blowholes in the lower portion of the rimmed ingot perpendicular to the surface and close to it, while on the killed ingot there are no blowholes of this type in the ingot shown in Fig. 1 and very small ones close to the surface in the lower part of the ingot shown in Figs. 2 to 4. With respect to the presence of pipe and the primary blowholes, the structure may vary considerably in both rimmed and killed ingots, therefore these cannot be considered as fundamental structural characteristics differentiating the two types of steel. The primary blowholes in rimmed ingots may be much less pronounced than those in the ingot shown in Figs. 5 to 7—as, for example, in "ingot iron," which is entirely free from them. An example of a cross section of an ingot-iron ingot is shown on page 16 of "Research and Methods of Analysis of Iron and Steel," published by the American Rolling Mill Co. (1920). A certain amount of pipe may also occur in rimmed ingots, though it is normally porous and not as well defined [or deep as in the killed ingot of Fig. 1. In killed ingots, primary blowholes may occur near the surface, as in Figs. 2 to 4, and

Jan 1, 1937

By L. K. Jetter, C. J. McHargue

The use of axis charts for representing the texture of cold-rolled thorium sheet was compared with conventional pole figures. Four texture components were deduced from the axis charts and shown to be consistent with the pole figures. It was shown that consideration of the pole figures alone could lead to an apparent component which is the average of two actually present. It was also shown that the spread about the "ideal" textures and the amount of material associated with each could be readily obtained Fom the axis chart method. BECAUSE of the crystallographic nature of the deformation mechanisms in metals, plastic flow results in the alignment of certain crystallographic directions with the primary flow directions. In the study of the "preferred orientation" thus developed, one wishes to discern the distribution of the crystallographic directions with respect to some reference direction, usually a direction related to the fabrication procedure, such as the rolling direction. The pole-figure method, introduced by ever,' involves the plotting of the distribution of the poles of some family of planes on a stereographic projection which places the reference direction(s) at the north pole and/or in the center. By noting the angles between the reference directions and concentrations of poles on several such pole figures, one can deduce the crystallographic directions which are aligned with the reference directions. If the preferred orientation is relatively simple and well-developed, one to three pole figures may be sufficient for obtaining the desired information; if there are several texture components, more pole figures may be needed. A significant improvement in the method of representing the textures in wires and rods resulted from the introduction of the "inverse pole figure" or axis-distribution chart by Harris.2 Such a chart gives directly the distribution of the reference axis relative to the standard stereographic projection. There has been widespread acceptance of this method for the representation of fiber textures, and methods have been proposed for converting observed diffraction intensities into axis densities.2-6 The suggestion by Mitchell and Rowland3 and Jetter, McHargue, and williams5 that sheet textures could be represented as distributions of rolling, normal, and transverse directions have been criticized on the basis that they offer no significant advantage over a combination of two ordinary pole figures and that it has not been proved that sheet textures can be treated as quasi fiber textures.6 If the purpose of a texture determination is to study some property which is related to the orientation of a particular crystallographic plane or direction, then conventional pole figures certainly are sufficient. For example, the distribution of the slip planes in face-centered cubic metals (the (111) pole figure) serves to indicate the variation in mechanical properties of sheet. On the other hand if the study is directed at an understanding of the factors influencing texture formation, it is desirable to know not only the preferred orientation but the kind and degree of spread from it and the relative amounts of material in each component, if there are more than one. Axis charts give this information as well as the orientation distributions. Consider the procedure for deducing a texture component from a pole figure for the (111) planes

Jan 1, 1961

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric pressure and by heat transferred to it from rock at high temperature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. METHODS Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1941

By Paul L. Russell

THIS is a progress report of an experiment being undertaken in cooperation with the Bethlehem Steel Corp., the Crucible Steel Co., and the Rock Bit Sales and Service Co., involving heat treatment of the shank ends of drill steel. This experiment is being conducted by the U. S. Bureau of Mines in its experimental mine, Mining Research Branch, Bluemont, Va. The purpose of the experiment is to determine the effect of an increase in the time the steel soaks in the furnace during the hardening heat. It has been thought that increasing this time produces a soft zone below the lugs resulting in a metallurgical notch that causes early failure. Each of the steel companies furnished enough 11/4 - in. straight carbon, hollow, round steel to make up 10 sets of drill steel, in each instance the steel bars were from the same heat. These sets of drill steel, consisting of 2-ft, 4-ft, 6-ft, and 8-ft lengths were fabricated by the Rock Bit Sales and Service Co. Special attention was given to the forging of the steel to produce the best rods possible. The heat treatment of all thread ends was identical and followed the best practice. The heat treatment of the shank ends of five sets of steel from each company produced a soft zone 2 to 4 in. in front of the lugs. It was decided that possibly the best way to obtain this effect was not to overlap the hardening heat but to let the steel soak for an additional 30 min before quenching. Therefore the only variable in the test steels is the length of time the shank ends were in the furnace. The remaining drill steel shanks were treated as follows: Heat treatment in pyrometer-controlled furnace at 1550°F. Quenching oil at 105°F to 125°F temperature. Areas for heat treatment were; shanks, 11 in.; threads, 9 in. Time at heat, standard practice, 20 min for 11/4-in. steel. Actual drilling tests were made in greenstone, (a metamorphosed basaltic rock), and in epidosite. Greenstone has a specific gravity of 2.96 and a compressive strength of 44,200 psi. Epidosite has a specific gravity of 3.26 and a compressive strength of 63,100 psi. All drilling tests were made using a 31/2-in. column-mounted, automatic feed drifter, with a controlled air pressure of 90 psi at the throttle. Tungsten-carbide bits of 2 in. diameter were used for all drilling. Contrary to expectations the drill steels that were allowed to soak for the additional 30 min before quenching performed better than the steels that were heat treated according to standard practice. This performance, as shown in Table I, was especially noticeable in the drilling of epidosite. The "longheat" drill steels furnished by Company "A" drilled 154 pct more minutes than the "standard-heat" steel. Expressed in feet, the "long-heat" steel drilled 114.60 ft more before failure than the "standard-heat" steel. The "long-heat" steel furnished by Company "B" drilled 37 pet more minutes or 60.39 ft more before failure than the "standard-heat" drill steel. The effect of the long heat treatment was not as evident when the steels were drilling in greenstone (Table II). In greenstone, the increase in minutes drilled by the "long-heat" steel over the "standard-heat" steel was 47 pet and 1 pet, respectively, for Companies "A" and "B."

Jan 1, 1952

By J. E. Howard

On Aug. 25, 1911, a rail failed on the Lehigh Valley Railroad, causing a disastrous wreck. The surface of the fracture was in a plane at right angles to the length of the rail. There was a dark-colored, oval spot on this surface, located on the gage side of the head, representing the part of the rail which was the first to fracture. The nucleus of this spot showed that the fracture had an interior origin. Other fractures of this kind, the peripheries of which had not reached the surface of the rail, presented surfaces having a (silvery luster. The darkened surface of the present fracture was caused, doubtless, by the air having had access to it. This fracture was recognized as a fatigue fracture, of a modified type, its interior origin having been due to a component in the rail which is not usually present in cases of fatigue fractures. The metal next the running surface of the head of the rail was in a state of internal compression, this being the component not commonly met with in other cases, and which caused the fracture to have its interior origin. For the purpose of giving this modified type of fatigue fracture a specific name, for identification, the term "transverse fissure" was applied. No mystery was thought to attach to its formation, or to its development. The explanation of its occurrence seemed obvious in the light of common knowledge upon the behavior of steel under repeated alternate stresses.' By reason of the state of internal compression at the running surface, the maximum tensile stresses in the head, ander bending loads, were along an interior element. Here the tensile strains were higher than in the fibers more remote from the neutral axis. Under such conditions the fracture of the rail would be expected to have an interior origin. A discussion of the subject of transverse fissures essentially becomes a discussion of fatigue fractures, since they are believed to be identical. The descriptive term employed, merely for the identification of this type of fatigue fracture, had the appearance of creating alarm. Apprehensions arose that a new phenomenon in the physical properties of steel had presented itself, the explanation of which was sought in every

Jan 1, 1918

By Frederick A. Mumpton

For more than 200 years zeolites have been familiar minerals to geologists and mining engineers as minor, but ubiquitous constituents in vugs and fractures of most basalt and traprock formations. More than 35 different species have been recognized including several, such as chabazite, erionite, mordenite, and faujasite, whose adsorption properties rival those of many synthetic molecular sieves. Igneous occurrences of this type have never been mined on a commercial scale; they are generally small and low grade, and they commonly contain as many as four zeolite minerals, along with small quantities of calcite, quartz, and other silicate minerals. Their economic beneficiation to monomineralic zeolite products has also not been achieved and, for the most part, industrial applications of zeolites have relied primarily on synthetic molecular sieves that were crystallized from hydrous aluminosilicate gels. During the middle 1950s, when Union Carbide Corp. and other groups were developing processes and markets for their fledgling synthetic zeolite businesses, natural zeolites

Jan 1, 1975

By B. P. Mulcahy

When the phrase "selection of coal for carbonization" is used, there is always the implied continuance of thought "to make good coke.'' The reason for this, of course, lies in the fact that, in almost all instances, when coal is carbonized coke is the principal product. Under certain conditions the yield of gas may also be a factor, but even here it must be secondary to the coke yield, for in every instance coke represents the largest single product of the process. The importance of coke to the byproduct industry has been considerably enhanced during the past 20 years because of the continuously decreasing financial returns of all the by-products. This fact will account, in part, for the rebirth of interest and investigation in the carbonization process during the past 10 years. Many papers have been written on this subject, with naturally divergent thoughts because of the diversity of interests, but in each instance the common aim was the same—the making of better coke. Scope of Investigation In perusing this literature, the writer was struck with the constantly recurring imposed condition of asking for better coke, but with the distinct unwillingness to make any concession to temperature of carbonization. When there is a high demand for coke, the only means by which the industry can increase the quantity is to shorten the coking time by an increase in temperature, or to increase the quantity of low-volatile coal, or both; and since in many instances the percentage of low-volatile coal can be increased only in small quantities, because of factors to be discussed later, the big increase must come from shortening the coking time. When this is done most of the improvement accomplished by the selection of the coals in the mixture is lost. It is not felt necessary in this paper to discuss the advantages of minimum ash and sulphur and other materials in coal. The value of minimum contents of these materials in coke is well established. When the use of coals high in these contents is dictated, the selection of coals, as we will consider it here, cannot apply to full advantage. The scope of this paper, then, will be to discuss the factors of inherent coal characteristics and operating procedures that influence coke quality, for they are fundamentally related and both must be considered if we are to attain our objective of better coke. A study of either must embrace a study of both simultaneously. To properly evaluate the influence of the coal and to help in the selection, we must first be able to appraise the coke, and interpret fairly the influence of the process in all of its aspects. Appraisal of Coke To refer simply to the quality of coke gives no indication of what is meant, for the term is too general in its implication. An analysis of a coke is divided usually

Jan 1, 1944

By B. P. Mulcahy

When the phrase "selection of coal for carbonization" is used, there is always the implied continuance of thought "to make good coke.'' The reason for this, of course, lies in the fact that, in almost all instances, when coal is carbonized coke is the principal product. Under certain conditions the yield of gas may also be a factor, but even here it must be secondary to the coke yield, for in every instance coke represents the largest single product of the process. The importance of coke to the byproduct industry has been considerably enhanced during the past 20 years because of the continuously decreasing financial returns of all the by-products. This fact will account, in part, for the rebirth of interest and investigation in the carbonization process during the past 10 years. Many papers have been written on this subject, with naturally divergent thoughts because of the diversity of interests, but in each instance the common aim was the same—the making of better coke. Scope of Investigation In perusing this literature, the writer was struck with the constantly recurring imposed condition of asking for better coke, but with the distinct unwillingness to make any concession to temperature of carbonization. When there is a high demand for coke, the only means by which the industry can increase the quantity is to shorten the coking time by an increase in temperature, or to increase the quantity of low-volatile coal, or both; and since in many instances the percentage of low-volatile coal can be increased only in small quantities, because of factors to be discussed later, the big increase must come from shortening the coking time. When this is done most of the improvement accomplished by the selection of the coals in the mixture is lost. It is not felt necessary in this paper to discuss the advantages of minimum ash and sulphur and other materials in coal. The value of minimum contents of these materials in coke is well established. When the use of coals high in these contents is dictated, the selection of coals, as we will consider it here, cannot apply to full advantage. The scope of this paper, then, will be to discuss the factors of inherent coal characteristics and operating procedures that influence coke quality, for they are fundamentally related and both must be considered if we are to attain our objective of better coke. A study of either must embrace a study of both simultaneously. To properly evaluate the influence of the coal and to help in the selection, we must first be able to appraise the coke, and interpret fairly the influence of the process in all of its aspects. Appraisal of Coke To refer simply to the quality of coke gives no indication of what is meant, for the term is too general in its implication. An analysis of a coke is divided usually

Jan 1, 1944

By Forbes Rickard

Gilpin County, the cradle of mining in Colorado and the Cornwall of North America, is too well known to need much introduction; get, for the benefit of those not familiar with the district, it may be well to premise that it comprises a tract of country of about 122 square miles, lying between the counties of Jefferson, Boulder and Clear Creek, and hounded on the west by the main range of the Colorado Rockies. It is located centrally in the State, 40 miles west from the city of Denver. During the 38 years since the first gold-discovery, Gilpin county has contributed about eighty million dollars in gold and silver to the world's supply of these metals. Many mining districts have had their rise and decline in half this time; but, very far from being exhausted, this mining district is still in the ascendant; its output is increasing (it was $3,600,000 for the year just closed), and it was never more prosperous nor productive than to-day. Taken generally, there does not exist anywhere in the world so great a number of permanent veins within so small an area as in this district. Gilpin is practically a " poor man's camp." Its veins, with few exceptions, outcrop at the surface. In the oarlier---days of the camp these outcrops were worked in many instances by sluice-mining; particularly is this the case with regard to the veins of the Russell gulch. Discoveries are still made in the heart of this district, and the productive area is every year extending its limits. The districts of Yankee Hill, Hawkeye and Pine Creek, which used to be isolated, are now part and portion of the one gold-field of Gilpin county. Within the last year sensationally rich gold-discoveries have

Jan 1, 1899

By I. C. White, G. H. Ashley, J. A. Bownocker

Among the rich mineral deposits of the great Appalachian field, the Pittsburgh coal bed stands pre-eminent. Other coal beds may cover a wider area, or extend with greater persistence, but none surpasses the Pittsburgh seam in economic importance and value. It was well named by Rogers, and his able assistants of the First Geological Survey of Pennsylvania, in honor of the city to whose industrial growth and supremacy it has contributed so much. Whether or not the prophetic eye of that able geologist ever comprehended fully the part which this coal bed was to play in the future history of the city that gave it a name we do not know; but certain it is that the 7 ft. of fossil fuel, which, in Rogers' time, circled in a long black band around the hills and, overlooking the site of Pittsburgh from an elevation of 400 ft. above the water of the Allegheny and Monongahela, extended up the latter stream in an unbroken sheet for a distance of 200 miles, has been the most potent factor in that wonderful modern growth that has made the Pittsburgh district the manufacturing center of America, and that bids fair to continue until it shall surpass every other district in the world, even if it does not now hold such primacy.' The Pittsburgh coal bed stands today as probably the largest contributor of wealth of any single mineral deposit in the world. If it is not, what other deposit is? It has contributed to Pennsylvania alone more than 2,500,000,000 tons of high-grade coal worth nearly $4,000,000,000; since 1910, it has added more than $2,500,000,000 to the value of Pennsylvania's mineral output. In 1920, this bed2 contributed 127,227,000 tons of coal as follows: Pennsylvania, Pittsburgh district........................ 38,245,000 Connellsville district................................. 34,095,000 Weatmoreland-Ligonier district........................ 16,107,000 88,447,000 West Virginia, Fairmont district........................ 15,571,000 West Virginia-Ohio, Panhandle No. 8 district............. 21,128,000 Maryland-Potomac (Est. one-third of production)......... 2,081,000 38,780,000 Total........................................... 127,227,000

Jan 1, 1927

By John V. Beall

There is an underlying surge to mining in the Philippines." So said A. R. "Ham" Reed, general manager Itogon-Suyoc Mines, Inc., to this reporter last November. Itogon-Suyoc is a small company with a struggling gold mine, a mixed sulfide mine and some prospects. In the Republic of Philippines (ROP), politics, which have an effect on mining, create some uncertainties. By July 1974, no mining company may have more than 40% foreign ownership. The ownership provision is a matter of concern to such important companies as Atlas and Benguet Consolidated and is generally considered a deterrent to new foreign investment. Under these circumstances, Reed's comments are of interest. On foreign prospectors: Don't come in cold; find a Philippine partner or buy into a company already here. Physical conditions of exploration are tough-terrain, communications -but the mineral potential is excellent.

Jan 4, 1969

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By Frederick N. Rhines, William A. Anderson

The investigations of Wymanl have demonstrated that copper deoxidized with several of the commonly used agents that confer immunily to ordinary hydrogen em-brittlement can still be embrittled if it is annealed alternately under oxidizing and reducing conditions. During the oxidizing cycle, oxygen diffuses into the copper and frequently deposits a subscale composed of the oxide of the residual deoxidizing agent. Upon subsequent reduction with hot hydrogen, the copper becomes ruptured along the grain boundaries to a depth sharply limited by the previous penetration of oxygen as delineated by the inner boundary of the subscale. Obviously the sensitivity to this kind of hydrogen embrittlement is engendered by the introduction of oxygen during the oxidizing anneal, but beyond this the mechanism of the process, and hence the controlling factors, remain obscure. There are several possibilities: (I) oxygen dissolved in the copper matrix of the subscale may, upon cooling prior to the hydrogen anneal, precipitate as cuprous oxide which is subsequently reduced by hydrogen as in the familiar case of hydrogen embrittlement; (2) oxygen in solid solution in copper may itself confer susceptibility to embrittlement by hydrogen; (3) the normally refractory oxides such as those of aluminum, silicon and titanium may themselves be reduced by hydrogen when in contact with copper; or (4) the precipitated oxides of the subscale may be complex compounds such, perhaps, as SiO2.Cu2O, which are partially reduced by hydrogen. These possibilities have been examined, and it has been concluded that the first three and possibly the fourth are operative collectively or individually under more or less predictable conditions. Effect OF Precipitated Cuprous Oxide and Dissolved Oxygen The literature provides no definite proof that oxygen in solid solution in copper can confer susceptibility to hydrogen embrittlement; indeed, the research of Leiter2 seemed to indicate the opposite—that to produce the effect, cuprous oxide must be present in massive form and in a more or less continuous network along the grain boundaries. To test this point, pure copper has been annealed in hydrogen under conditions designed to ensure the presence in various samples of: (I) precipitated cuprous oxide, (2) dissolved oxygen only, and (3) no oxygen in any form. Very pure copper" said to contain no oxygen and no spectro-scopically detectable traces of any other element (that is, no individual detectable impurity in quantity greater than 0.0001 per cent) was used. Strips of this material cold.-rolled 75 per cent to 1/8 in. in thickness were subjected to the following treatments, the results of which are noted:

Jan 1, 1941

By Frederick N. Rhines, William A. Anderson

The investigations of Wymanl have demonstrated that copper deoxidized with several of the commonly used agents that confer immunily to ordinary hydrogen em-brittlement can still be embrittled if it is annealed alternately under oxidizing and reducing conditions. During the oxidizing cycle, oxygen diffuses into the copper and frequently deposits a subscale composed of the oxide of the residual deoxidizing agent. Upon subsequent reduction with hot hydrogen, the copper becomes ruptured along the grain boundaries to a depth sharply limited by the previous penetration of oxygen as delineated by the inner boundary of the subscale. Obviously the sensitivity to this kind of hydrogen embrittlement is engendered by the introduction of oxygen during the oxidizing anneal, but beyond this the mechanism of the process, and hence the controlling factors, remain obscure. There are several possibilities: (I) oxygen dissolved in the copper matrix of the subscale may, upon cooling prior to the hydrogen anneal, precipitate as cuprous oxide which is subsequently reduced by hydrogen as in the familiar case of hydrogen embrittlement; (2) oxygen in solid solution in copper may itself confer susceptibility to embrittlement by hydrogen; (3) the normally refractory oxides such as those of aluminum, silicon and titanium may themselves be reduced by hydrogen when in contact with copper; or (4) the precipitated oxides of the subscale may be complex compounds such, perhaps, as SiO2.Cu2O, which are partially reduced by hydrogen. These possibilities have been examined, and it has been concluded that the first three and possibly the fourth are operative collectively or individually under more or less predictable conditions. Effect OF Precipitated Cuprous Oxide and Dissolved Oxygen The literature provides no definite proof that oxygen in solid solution in copper can confer susceptibility to hydrogen embrittlement; indeed, the research of Leiter2 seemed to indicate the opposite—that to produce the effect, cuprous oxide must be present in massive form and in a more or less continuous network along the grain boundaries. To test this point, pure copper has been annealed in hydrogen under conditions designed to ensure the presence in various samples of: (I) precipitated cuprous oxide, (2) dissolved oxygen only, and (3) no oxygen in any form. Very pure copper" said to contain no oxygen and no spectro-scopically detectable traces of any other element (that is, no individual detectable impurity in quantity greater than 0.0001 per cent) was used. Strips of this material cold.-rolled 75 per cent to 1/8 in. in thickness were subjected to the following treatments, the results of which are noted:

Jan 1, 1941

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938