Search Documents

By Tripp R. M., C. A. Heiland, Dart Wantland

This paper serves to illustrate the application of geophysics to a virtually abandoned mine properly, an application that led to the discovery of an ore body and thus afforded an Opportunity to cOmpare subsequent geologic findings with geophysical data. The work herein described represents, however: more than mere ''case history." It demonstrates that it is possible to obtain satisfactory results by simple means and relatively inexpericnced personnel. The geophysical surveys were made by students as a part of their field assignments in the course of their regular training, and were supervised by Dart Wantland, J. E. Hawkins and R. Maurice 'Tripp. In the course of several seasons an appreciable amount of material was accumulated, which gave graduate students an opportunity for special studies. In this connection, the contributions by L. Massé, R. C. Hyslop, and J. E. Hawkins deserve special mention. The property owners cooperated wholeheartedly in the work, and special thanks are due messrs. J. F. Johnson and S. E. Zelenkov, of the American Smelting and Refining Co., for their interest and for permission to utilize the results of their development work for this publication. Location and Geology The Malachite mine is situated on the northcrn slope of Bear Creek Canyon, 4 miles northeast of Evergreen, I½ miles northwest of Idledale, and 4% miles west northwest of Morrison, in Jefferson County, Colorado. The location (Fig. I) is north of the center of set. 30, T. 45, R. 70 W., at an elevation of about 7500 ft, above sea level, Near the mine the terrain slopes rather uniformly southward at an angle of about 180 pigs. 3 and 7). The geology of the Malachite mine area has been described by J, underhill,' W, Lindgren,2 and J. Boyd.3,4 A map showing surface outcrops and mine workings appears in Fig, 2. the Malachite mine is in an amphibolite belt enclosed in gneisses and schists of the Idaho-Springs formation (probably early Algonkian age). The highly contorted beds are nearly vertical and strike slightly north of west. A series of granite-pegmatite dikes have been intruded almost at right angles into the gneisses and schists and doubtedless are postmineral. While most of the formations are exposed at the surface, a part of the 'lope is covered by slide rock and float, and in the eastern portion by alluvium and creek fill. A quartz-diorite dike cuts through the amphibolite schists at a small angle with nearly vertical dip. The copper sulphides, developed in this dike by magmatic segregation, occur in lenticular form. As far as the mine workings have revealed, the ore lenses are often discontinuous in depth and

Jan 1, 1946

APPROXIMATELY 90 per cent of the steel that is melted and refined in the United States and poured into ingots is made in basic open-hearth furnaces, as shown in Table 1-1. The annual ingot capacity of the steel industry reported January 1, 1950, by the American Iron and Steel Institute3* was 99,040,160 tons, of which the basic open-hearth process accounted for 85,896,580 tons, 86.7 per cent of the .total. The capacity of the individual furnaces varies over a wide range, a large majority falling within limits of 50 to 200 tons (Fig 1-1). Most of the units constructed [ ] since 1942 are in the larger size groups, between 175 and 225 tons capacity.

Jan 1, 1964

By E. S. Rowland, J. Welchner, R. H Marshall

This paper presents results on an extension into the realm of high-carbon steels of some work recently published1 on the effects of time at temperature, quenching temperature and prior structure on the hardenability of one 0.20 and four 0.40 per cent carbon alloy steels. It was shown at that time that unless the conditions of time, temperature and prior structure are substantially the same in performing the hardenability test as in conducting hardening of parts in production, the correlation of hardenability information with the hardness and properties of production parts is often not of satisfactory accuracy. The general effects of these variables on the austenitic grain size, distribution of excess carbides and critical cooling rate have been known for many years and one or more have been investigated by Shepherd,2,3 Davenport and Bain,4 Digges,5,6 Digges and Jordan,' Post and associates8 and Roberts and Mehl,9 to mention only a few. There has been no systematic investigation, however, into the quantitative variations produced on the hardenability of commercial high-carbon steels by changes in these factors of time, temperature and prior structure. Procedure A plain carbon hypereutectoid steel, S.A.E. 52100 and Graph-Mo, a molybdenum-bearing high-carbon steel containing some graphite, were chosen for this investigation. The chemical analyses of these electric-furnace steels are given in Table I. The procedure used was exactly that reported previously,' hence the details will not be repeated here. Normalized (165o°F.) and spheroidized prior structures were utilized on all steels with hot-rolled and quenched (I600°F. oil) prior conditions added for the plain carbon steel. The end-quench test developed by Jominy10 was sclected for use in this investigation and, with the noted exceptions, the American Society for Testing Materials standard procedure was followed. The effect of time at temperature was examined at intervals of o, 10 and 40 min. and 4 hr., and a few 16-hr. tests were run. Salt-bath heating of the specimens was employed to control and minimize the

Jan 1, 1944

By R. H. Marshall, J. Welchner, E. S. Rowland

This paper presents results on an extension into the realm of high-carbon steels of some work recently published1 on the effects of time at temperature, quenching temperature and prior structure on the hardenability of one 0.20 and four 0.40 per cent carbon alloy steels. It was shown at that time that unless the conditions of time, temperature and prior structure are substantially the same in performing the hardenability test as in conducting hardening of parts in production, the correlation of hardenability information with the hardness and properties of production parts is often not of satisfactory accuracy. The general effects of these variables on the austenitic grain size, distribution of excess carbides and critical cooling rate have been known for many years and one or more have been investigated by Shepherd,2,3 Davenport and Bain,4 Digges,5,6 Digges and Jordan,' Post and associates8 and Roberts and Mehl,9 to mention only a few. There has been no systematic investigation, however, into the quantitative variations produced on the hardenability of commercial high-carbon steels by changes in these factors of time, temperature and prior structure. Procedure A plain carbon hypereutectoid steel, S.A.E. 52100 and Graph-Mo, a molybdenum-bearing high-carbon steel containing some graphite, were chosen for this investigation. The chemical analyses of these electric-furnace steels are given in Table I. The procedure used was exactly that reported previously,' hence the details will not be repeated here. Normalized (165o°F.) and spheroidized prior structures were utilized on all steels with hot-rolled and quenched (I600°F. oil) prior conditions added for the plain carbon steel. The end-quench test developed by Jominy10 was sclected for use in this investigation and, with the noted exceptions, the American Society for Testing Materials standard procedure was followed. The effect of time at temperature was examined at intervals of o, 10 and 40 min. and 4 hr., and a few 16-hr. tests were run. Salt-bath heating of the specimens was employed to control and minimize the

Jan 1, 1944

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

Binary alloys of titanium with silver, lead, tin, nickel, copper, beryllium, boron, silicon, chromium, molybdenum, manganese, vanadium, iron, and cobalt were studied. One-half-pound ingots of the alloys were prepared in an arc furnace, employing a water-cooled copper crucible, an argon atmosphere, and a water-cooled tungsten electrode. The half-pound ingots were fabricated by forging at 1700°F in air to 1/4-in. slab, followed by hot rolling at 1450°F to 0.060-in. sheet. Tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships were determined for these alloys. EARLY in 1947, as one phase of the evaluation of materials for Air Force Project RAND, Battelle successfully arc melted Bureau of Mines titanium and obtained a few basic properties of unalloyed titanium and several titanium-base alloys. The low density, excellent resistance to corrosion, and high tensile properties of these materials stimulated a great deal of interest among metallurgists and designers seeking better materials of construction. As a result of this early work, Battelle, under contract with the Air Materiel Command, Wright-Patterson Air Force Base, has continued extensive studies of titanium alloys. The result of the first year's work is described in three papers. The present one deals with binary alloys, the second with ternary alloys, and the third paper with quaternary alloys. Melting Method The arc furnace for melting titanium and other refractory metals was developed at Battelle Institute under Air Force Project RAND. During the present work, considerable improvement has been made in the design and operation of this furnace for making small ingots of titanium and titanium alloys. The improved furnace design is illustrated by fig. 1, which shows a cross-sectional view with the dimensions of various parts and their relationship to one another. The essential features of the furnace are the inert argon atmosphere, the water-cooled copper crucible, and the water-cooled tungsten elec- trode. The melting crucible is formed by spinning 0.064-in. annealed copper sheet. A groove for an O-ring seal is spun into the flange of the crucible. A fiber gasket between the crucible flange and the water-cooled brass cover provides electrical insulation. The brass cover is fitted with a sight glass, an opening for the water-cooled electrode, and a tube through which the material is charged. Direct current is used for melting, with the positive electrical terminal connected to the water jacket and the negative terminal to the electrode. A typical heat is made in the new furnace as follows: Approximately, 0.20 lb of titanium under 2 mesh per in. and the alloy addition, if any is to be used, are placed in the bottom of the crucible. The cover is clamped on the crucible so that the O-rings make a tight seal. The remainder of the charge is placed in a glass bottle, and this is connected by a rubber hose to the charging tube of the furnace. The crucible and the charge are evacuated with a mechanical pump to a pressure below 50 mm of mercury, or less if desired, and held at this reduced pressure for 5 min. Hot water is circulated through the jacket during the evacuation period to assist in outgassing the crucible. Following the evacuation, tank argon of 99.92+ pct purity is flushed through the crucible for 5 min and then adjusted to give a positive pressure of 1 to 2 psi. During subsequent operation, an argon pressure regulator introduces only enough argon to compensate for the small leakage which occurs through a mercury trap. Re-evacuation and reflushing the melting chamber with argon produced a negligible reduction in contamination. Two 550-amp generators, connected in parallel, constitute the power source. Normally, about 800 amp are used for melting alloys which are not extremely refractory. The generators are set for 90 v open circuit and 200 amp. The arc is struck and the electrode is withdrawn to produce an arc of 23 to 26 v. This voltage is maintained while the electrode tip is moved slowly around a circle 1 in. smaller than the diameter of the ingot. The current

Jan 1, 1951

By A. W. Griffith, R. G. Beverly, W. A. Millsap

THE Grand Junction Pilot Plant, operated by National Lead Co. Inc., for the U. S. Atomic Energy Commission, is engaged in the amenability testing of orebodies to establish design and cost data for commercial mills and to test new processes for recovery of uranium from ores. Test work was performed to study the effects of several variables on leaching of uranium ores in carbonate solutions. Many of these variables had been investigated in the laboratory, but pilot plant tests were desirable to evaluate their importance in semi-works equipment and to predict optimum operating conditions for future commercial mills. The results of these tests should serve as a guide in selecting the most efficient and economical method of leaching uranium ores amenable to a carbonate process. This article is concerned with a process in which uranium is extracted from the ore by a hot Na2CO3- NaHCO3 solution; the uranium-bearing solution is separated from the solid residue by filtration, and uranium is then precipitated by chemical means.

Jan 9, 1957

By Wm. Reuben Webster

BRASS is an alloy of copper and zinc. The brasses (using this term to denote all useful proportions of the two constituents) are the most valuable and widely employed of all [ ] nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure brass containing 70 per cent copper and 30 per cent zinc. Fig. 3 shows the effect of annealing at various temperatures on the same alloy. This effect is somewhat modi [ ] fled by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity -the hot hammer test. Samples Y2 in. in diameter and ¾ in. long are placed in a suitable furnace. These are withdrawn one at a time at successively higher tempera¬tures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of' reduction in length of the cylinders are plotted against temperatures and give a comparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By H. P. Moore, R. W. Fenn, Harold Margolin, W. R. Hibbard

DEFORMATION lines, also called etch markings or strain markings, are noneffaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries.1 Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrette to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation required for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted deformation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson' observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brick9 noted that deformation lines in 70-30 brass apparently associated with {111} planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards11 reported that in copper cold rolled less than about 50 pct few strain markings were apparent but for higher. reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass

Jan 1, 1948

By Colin Fink

TANTALUM and columbium occur together in tantalite and columbite ores, which may be considered as ferrotantalate (FeTa206), with part of the iron and tantalum replaced by manganese and columbium respectively, the general formula, therefore, becoming (Fe, Mn)O.(Ta, Cb)205. The ratio of tantalum to columbium is not fixed; the amount of tantalum may vary from one-third to three times that of columbium. Minerals having a high content of tantalum are called tantalite, while those possessing larger amounts of columbium are classified as columbite ores. These minerals are found in pegmatites and often occur in veins associated with cassiterite and wolframite, and may contain small amounts of tin, tungsten, titanium and silica.1

Jan 1, 1931

By Harry M. Callaway

IN times of a falling metal market the mine operator attempts to remain in competition by lowering his overall cost and raising the grade of ore he processes. But these adjustments can be made only within narrow limits imposed by inherent characteristics of the operation. Is there some additional method whereby the break-even point can be lowered? One approach, perhaps the only one, to lower a break-even point is careful cost analysis considering both fixed and variable costs in relation to mining rate. The following is an analysis of cost distribution and its significance in determining the most economic combination of the factors of ore grade and tonnage output applicable to a given mining operation.

Jan 4, 1958

By Arthur S. Dwight

THE professional career of Thomas Septimus Austin, who died at El Paso, Tex., August 23, 1906, was contemporaneous with the growth of the silver-lead smelting-industry of the Far West, to which his talents and zeal contributed in no small degree. Born at Stratford, Conn., December 7, 1853, he was the seventh son in a family of thirteen. His parents were well-to-do; and he received a thorough preliminary training at the Hopkins Grammar School, New Haven, Conn., passing thence to the Columbia School of Mines, in New York, where he was graduated in 1876. His first professional work was that of analytical chemist with a Cuban sugar company. In this position he spent a year, and, whatever else of benefit he may have acquired during that year in Cuba, he gained a facility of speech in the Spanish language which was of inestimable value in his subsequent work in Mexico and the southwestern United States. In 1877, he went to the Rocky Mountains, and, under the firm name of Murphy & Austin, opened an assay-office in Leadville, Colo., which was just then coming into public notice as a rich silver-lead camp. The next year, however, he entered the service of the Germania Smelting & Refining Co. at Salt Lake City, Utah, where he remained until 1882, first as assayer and chemist, and later as Assistant Superintendent. The Germanic bears the honorable distinction of being one of the first of the large " custom " lead-smelters erected in the West. Its founders may be called the pioneers of the modern lead-smelting practice, and the Germania served, to a large extent, as a model for the many plants that sprang into existence during the next few years in Utah, southern Idaho, Colorado and other lead-producing districts. The formulation, for the first

Jan 1, 1908

By Robert Glass Cleland

UPON the death of its founder, Phelps, Dodge & Co. entered upon a new chapter in its long and varied history. Thereafter, for nearly a decade, William E. Dodge largely determined and executed the policies of the company. The old firm, dissolved automatically by Phelps's death, was succeeded by a new partnership consisting of Anson G. Phelps, Jr., William E. Dodge, Daniel James, James Stokes, William E. Dodge, Jr., and D. Willis James, one of the three sons of Daniel James. Each of the first three partners owned a twenty-five-per-cent interest in the company, Stokes had a fifteen-per-cent interest, and the two younger partners each held five per cent. The new company bought Anson Phelps's holdings in the old firm from Olivia Phelps, his widow and executrix, for approximately seven hundred thousand dollars; but the new partnership, designed by agreement to last the usual five-year period, was brought to an end shortly before that time by the death of the younger Anson Phelps from small- pox. Perhaps because of poor health, the son had never been as deeply concerned with business as his father, but found

Jan 1, 1952

By J. D. H. Strickland, K. J. Jackson

IN previous papers' ' details were given of the constructlon and use of an apparatus to study the rate of chlorine consumption and the rate of sul- fate and sulfur production when dilute aqueous chlorine solutions were allowed to react with pyrite and galena in acid solutions at or near room temperature. The reaction with pyrite was very rapid, and hence entirely transport-controlled in its kinetics, and produced only ferric and sulfate ions. The behavior of galena was much more complex and was studied in some detail. Sulfur monochloride could be detected as a reaction product and both

Jan 1, 1959

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS, * LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first.

Jan 1, 1929

By T. R. Scott

The acid pressure leaching of zinc-lead flotation concentrates from the McArthur River deposit, Northern Territory, Australia, has been studied in a three-stage, continuous, co-current system, using titanium reactors of 6 gal capacity. The starting pulp contained 2.7 lb solids per gal of synthetic spent electrolyte and the final liquors contained 120-125 gpl Zn. Parameters investigated included temperature (95-120°C), oxygen pressure (30-100 psi), acid addition (80-130% of theoretical), and leaching time (35-65 min per stage). Technical factors studied included mixing and pumping of feed, agitation, settling and washing and control mechanisms. The chemistry of liquor impurities, of scale formation in autoclaves and of lead jarosites in residues was studied in some detail. Results indicated that 90-93% zinc recovery could be obtained with a "low- acid" process, using 113°C and 70 psig with oxygen as the favored operating conditions. Residues contained 16-18% elemental sulphur and 15% lead, together with unreacted pyrite and gangue minerals. Pelletizing of residues was impracticable, and alternative suggestions for the recovery of lead, sulphur and silver are discussed. Preliminary estimates for plant and operating costs are given and enable some comparison to be made with conventional procedures.

Jan 1, 1973

Jan 11, 1951

By T. A. Rickard

RICO, in the southwestern corner of Colorado, is one of the productive mining centers of the San Juan region, so-called because its waters drain into the river of that name, which is tributary to the Colorado. The San Juan region includes the counties of Ouray, Hinsdale, San Miguel, Dolores, San Juan and Montezuma. It is traversed by a network of picturesque mountain ranges on whose lofty summits there rests perpetual snow. The region is peculiarly rugged, and, in the early days of its development, tested to the full the hardihood of the adventurers who first explored its can ions 111 search for gold and silver. A prospecting party, guided by Jim Baker, scout and trapper, penetrated in 1861 this part of the territory of Kansas. At that time the country was in the possession of the Ute Indians. In October, 1873, by the Brunot treaty, they ceded to the United States Government the richest mineral-bearing portion of their

Jan 1, 1897

By H. T. Hildage

Although Greater New York does not bear any resemblance to a great mining district, the mining operations that are being conducted in and about the city are both extensive and interesting in character. With regard to the extent, it may be mentioned that, at present, there is more dynamite used in New York than in any mining district in the United States; that there are under construction about 38 miles of tunnel, and that 66 miles more are projected, most of which must be constructed .in the near future; that since 1903 at least 2,000,000 tons of earth has been removed in underground work, in addition to about 3,500,000 tons that has been removed in open-cut in connection with tunnel-work, and many times this quantity that has been removed in excavating foundations for buildings not connected with tunnel-work; and that there are to-day probably more than 5,000 men engaged in mining-work in and about New lrork City. These undertakings include almost every operation connected with underground work, from exploration by means of trench and boring, to the sinking of large shafts and the driving of large tunnels through every kind of ground from hard rock to soft, semi-fluid silt and quicksand. It is proposed in this paper to give a general description of some of the methods and appliances used in the opening-up of a " mine " in a large city, and a brief description of some of the &'mines" now being developed in New York, connecting as far as possible the methods described with the particular work for which they were designed, in order to give a general idea of the

Jan 1, 1908

By T. H. Alden

In several recent studies of fatigue fracture in single-phase metals, tests have been made using the condition of essentially constant plastic strain amplitude.1-4 This procedure departs from the more common practice of holding the amplitude of stress constant. From these studies have emerged two important generalizations about the behavior of metals during cyclic straining. First, measurements of the stress amplitude, required to impose the fixed plastic strain amplitude, have shown that the rate of cyclic strain hardening in annealed metals is rapid in the early cycles but decays quickly to a very low value.1"5 This behavior is displayed particularly for a range of strain amplitudes below about 2 pct and at low and high temperature. Frequently, the hardening rate becomes so low that one can determine a "saturation" stress. This stress increases with strain amplitude. In addition, an experimental relation between fracture life and plastic strain amplitude was obtained by Coffin and Taternelli,' namely N 1/2 ep = constant. For several metal:;, this equation has been shown to hold down to a strain amplitude of 0.1 pct. Whether it also holds in the "low amplitude" range (lives of more than about 105 cycles) has not been established. The importance of the saturation stress level (a value derived from strain hardening measurements) to the question of fracture life (the usual quantity of interest of fatigue testing) lies in the observation that cracks start to form when the cyclic hardening rate is essentially zero, and not before.4"5 This point suggests immediately a means of relating tests at constant stress and constant strain amplitudes. When making comparison, the stress in a constant stress test is to be identified with the saturation stress in a constant strain test. If these ideas are correct, then it should be possible, using the relation between fracture life and strain amplitude and experimental curves of saturation stress versus strain amplitude, to predict the fracture life as a function of stress, i.e. predict the S -N curve, for low stress fatigue. Saturation stress amplitude-plastic strain amplitude data, obtained in tension-compression, exist only for a few metals and for relatively high amplitudes of strain. Comparable S -N curves (push-pull loading) were known by the author only for OFHC copper. Values for this metal taken from Ref. 2 are shown in Fig. 1. The strain amplitudes, the lowest

Jan 1, 1962

By J. H. McCormick

THIS plant, near Marysville, Mont., was planned to treat the ore from the Piegan and Gloster mines, the latter being one of the early and famous producers of the Marysville district. When the mill was closed in 1888, treatment consisted of stamp milling, followed by pans and settlers for pan amalgamation. The extraction was evidently poor; because, a few years later, thousands of tons of tailings were re-treated by the ranchers in the valley below the mill, by the then new cyanide process, and gave a handsome profit. In 1914, the present owners, after laboratory tests and an experimental mill run, decided upon the following treatment: crushing to 40 mesh in cyanide solution, concentration, amalgamation, classification, and cyanidation of sands by leaching, and of slime by agitation and decantation in charges. The ore averaged about $7 per ton, gold and silver, the ratio of weight being 1 oz. gold to 7.56 oz. silver. The ratio of gold and silver in tailings was 1 oz. Au to 36.6 oz. Ag; the quartz vas sharp and, sandy, however finely ground, and rather difficult to slime. The mechanical 'equipment was a No. 5 Symons gyratory crusher; three 10-ft. Lane slow-speed Chilean mills; one Wilfley roughing and one finishing table; one submerged-type Akins classifier; five 26 by 10-ft. fir leaching tanks; one 24 by 7-ft. Dorr thickener; four 14 by 16-ft. Dorr agitators; four 6-compartment double-row zinc-boxes having compartments 18 in. wide, 18 in. deep, and 34 in. long; Johnson zinc lathe; acid and vacuum filter tanks for treating precipitate; roasting furnace; and Case tilting No. 275 crucible furnace for melting precipitate. The mill is driven by electric power supplied by the Montana Power Co. at the following rates, per kw.-hr.: 200 to 300 hp.,.0.68 c.; 300 to 500 lip., 0.61 c.; 500 to 750 hp., 0.55 c.; plus $1 per month per installed motor horsepower.

Jan 8, 1918