Search Documents

By J. B. Clark

An exploratory study of the 60 wt pct Mg and 80 wt pct Mg sections of the solid constitution in the magnesium-rich region of the Mg-Al-Ca-Zn system was undertaken. The objective of the investigation was to determine the general configuration of the phase fields with respect to the magnesium solid solution in this complex system. The 335°C (635°F) tetrahedron was selected for study because the solid constitutions of the bounding ternary systems—Mg-Al-Zn,1 Mg-A1-Ca,2 Mg-Ca-zn3—were well known and, at least in these ternary systems, diffusion was rapid enough at 335°C for equilibrium to be reached fairly rapidly. Metallography and powder X-ray diffraction were selected as the best corroboratory methods for determining the solid phase equilibria. A total of forty-six quaternary alloys on the 60 wt Mg and 80 wt Mg sections were prepared, annealed to equilibrium at 335°C, and the phases present identified. Singly sublimed (99.99 pct) magnesium, electrolytic (99.99 pct) zinc, high-purity (99.99 pct) aluminum, and USP calcium were alloyed in graphite crucibles under a chloride flux and chill cast into a split graphite mold. Alloy samples were sealed under argon in Pyrex vials and annealed at 335°C ± 1/2° for a minimum of 500 hr. At the conclusion of the anneal, the alloy samples were quenched rapidly in ice water. Standard metallographic procedures for magnesium alloys were used. Powder X-ray diffraction patterns were taken on a G. E. Camera with a diameter of 14.32 cm using nickel filtered copper radiation. The phase equilibria in the 60 wt pct Mg section of the 335°C (635°F) tetrahedron is shown in Fig. 1. The complex equilibria in the zinc-rich region were not accurately determined and are shown only tentatively with dotted lines. The equilibria of the three bounding ternary 335°C sections from pure magnesium to 60 wt pct Mg are also shown as though folded away from the tetrahedron. The 80 wt pct Mg section has the same configuration of phase fields as that shown in Fig. 1. Thus it is reasonable to conclude that in higher magnesium sections, the same relative configuration of phase fields is maintained though the relative proportions of the individual phase fields may change slightly as the magnesium solid solution is approached. Note that all the ternary phases present in these ternary diagrams enter into the quaternary equilibria with the exception of the phase of the Mg-Al-Zn system which becomes unstable with the addition of as little as 1/2 pct Ca. No quaternary intermetallic phases were found. No liquid phase was detected in any of the quaternary alloys annealed at 335°C suggesting that if a quaternary eu-tectic exists, it must lie between 335°C and 339°C, the temperature of the ternary eutectic in the Mg-Al-Zn system.

Jan 1, 1962

By Strathmore R. B. Cooke, Marcus Digre

That calcium will activate quartz for flotation with anionic collectors such as soaps has been known for a number of years,12'3 and the method has been applied to the concentration of various iron ores4 5 6 as well as to other materials. Clemmer gives the permissible pH range for the activation of quartz by calcium as between 9.5 and 12.5 with an optimum value of 11.0, and Hertzog7 has determined the calcium abstraction of iron ores and of Ottawa sand, but otherwise little quantitative data are available. The purpose of the present investigation was to determine those conditions under which dilute solutions of calcium chloride will activate quartz for anionic flotation and to determine the amount of calcium ion adsorbed by quartz. Those variables, the influence of which was primary, such as calcium, sodium, and hydrogen ion concentrations, were studied. Other factors which influenced the results are discussed in the description of the experiments. Three different experimental methods were used to determine the activation of the quartz. The first method was to treat a sample of ground, deslimed quartz with solutions of calcium chloride and sodium hydroxide, and to determine the calcium adsorbed by chemical analysis of the solution. Advantages are that a direct value for the amount of calcium adsorbed is obtained, and introduction of a collector which may affect the adsorption is avoided. The difficulty is to determine the extremely small differences in the calcium concentrations before and after the abstraction. The second method was to determine the activation of the quartz by observing the contact angle obtained on pressing an air bubble against the polished surface of a piece of quartz immersed in a solution of calcium chloride, sodium hydroxide, and sodium oleate. This is the well-known "contact angle" method. The third method was to determine those conditions under which an air bubble will pick up quartz particles immersed in a solution of the desired reagents. Disadvantages common to the sec- ond and third methods are that introduction of a collector is necessary to obtain bubble contact with the mineral; very small quantities of contaminant can give erroneous results; and no information is obtainable concerning the amount of calcium adsorbed. Advantages are that tedious analyses, which at best give approximate results, are avoided, and the conditions, especially for the third method, closely simulate those of actual flotation. Although the most consistent results were obtained with the third method, this paper describes the techniques used and the results obtained from each of the three methods. Distilled water and analytical grade reagents were used throughout except where otherwise stated. Between tests all glass articles were cleaned with a chromic-sulphuric acid mixture and sodium hydroxide. Abstraction Method The raw material for the tests was Ottawa sand sized between 14 and 28 mesh. Batches of 500 g of this sand were dry ground for 1 hr in an Abbe porcelain mill with 2700 g of quartz pebbles. The batches were split down to samples weighing approximately 30 g, and the weight of each sample was adjusted to exactly this value.

Jan 1, 1950

By E. W. Hough, G. L. Stegemeier

Empirical equations for surface tension of propane and normal butane as functions of reduced temperature are obtained from experimental data. Another correlation relating surface tension to enthalpy of vaporization is given for these two compounds. In addition, new paracbor numbers are calculated for the normal paraffin hydrocarbons. These numbers are utilized for the calculation of interfacial tension of two-component systems as functions of pressure and temperature, using a modified form of Weinaug-Katz equation. The experimental data for two binary systems are approximated by the correlation. From these results it is found that the interfacial tension in the high-pressure region remains extremely low at large pressure decrements below the critical pressure. Thus, it appears that condensate systems may have flow characteristics almost like single-phase conditions even though the pressure is within the two-phase region. Experimental data have shown that interfacial tension divided by density difference approaches zero as the critical pressure is approached. A calculation of wetting-phase saturations indicates that the saturation gradient at the two-phase contact becomes increasingly abrupt as the critical pressure is approached. DISCUSSION Prediction of the surface and interfacial tension of the light hydrocarbons and of two-component hydrocarbon mixtures at various temperatures and pressures may be made if other physical properties are known. Extensive experimental work on single-component and binary systemsl is the basis for the correlations outlined in this paper. Interfacial tension is defined as the specific surface-free energy between two phases of unlike fractional composition, while surface tension is defined as the specific surface-free energy between two phase:; of the same fractional composition. The usual definitions relating interfacial tension to a liquid-liquid interface and surface tension to a gas-liquid interface are not clearly defined when the critical region is included, and there is no sharp distinction between a gas and a liquid phase. Interfacial tension is probably the most important single force that makes one-half to one-third of the total oil actually in place in a reservoir rock unrecoverable by conventional gas-drive or waterflood methods. A rough estimate of this figure for the United States is 100 billion bbl. Interfacial tension presently is used by petroleum engineers in the estimation of saturation gradients at the gas-oil contact and at the oil-water contact. The data in this paper should prove useful for estimates of reserves involving gas-oil contacts. Relative permeability undoubtedly is influenced by interfacial tension, for sufficiently small values. These data should be useful in determining how small the values are In addition, these data should eventually add to our fundamental knowledge of surfaces. At the critical point, all surface excesses approach zero and the thickness becomes very large. SINGLE-COMPONENT SYSTEMS It has been observed1 that the following relationships are good approximations to the physical properties of propane and n-butane.

By Don M. Jackson

The techniques for the growth and controlled, graded doping of silicon epitaxial overgrowth layers were established. Grading of- impurities such as arsenic or boron in arbitrarily chosen profiles oiler four orders of magnitude (from I X 10Lg to 1 X 10L5 cm) was accomplished. The graded structures were grown in a stepwise manner where in the profiles were approximated by growing many separate layers with small doping-level changes between layers. Masked-area growth of silicon through windows in a SiO2 masking film was acconiplished through the simultaneous injection of HCl gas 102th Sic14 in the epitaxial reactor. The HCl served to inhihit the growth of silicon on the Sz02 surface, and also to control the cross-sectional profile of the silicon mesas. silicon from the substrate was etched out through the windows, and then epitaxial material was used to fill the holes hack in to form planar diodes. Simullaneous HCl injection was adapted to control the cross-section profile of the hack-filled regions. Arsenic-huried regions beneath in te- In recent months, the epitaxial growth process in semiconductor materials technology has evolved into a complex system directed at both material improvement for better monolithic integrated-circuit characteristics and the development of new silicon structures for future integrated-circuit needs. The advent of high-temperature HC1 gas etching1 grated-circuit transistors reduced V(SAT) by slightly more than one third, bringing this parame-ter to that of an isolated component transistor. When arsenic was diffused into the starting sub-stvate, it was necessary to remove any excess arsenic in order to avoid excessive audodoping of the subsequent epitaxial layer. Oxide isolation of single-crystal regions in a substrate provided complete electrical isolation of integrated-circuit components, thereby eliminating parasitic capacitance which is inherent in standard integrated-circuit processing. The process involved the etching of deep mesas on silicon Wafers, the formation of an oxide over the mesa surface, and then the deposition of several mils of polycrystalline silicon over the oxide. The original substrate was lapped and polished allay until the mesas were left isolated in the polycrys-talline matrix. The Final components were fabri-cated in the single-crystal islands. Speed and power-handling capabilities of standard circuits were improved through the process. wherein work-damaged material is removed from the surface of the silicon wafer just prior to the silicon deposition step has made it possible to grow silicon films with structural quality that approaches that of the substrate. HBr used in the same volume ratio as HC1 etches silicon at the same rate and with the same results as HC1. Recent developments in epitaxial materials technology have occurred in the areas of precise doping control, buried prediffused regions between over-

Jan 1, 1965

By Peter J. Maxworthy

INTRODUCTION There is no hard and fast rule on whether functions within a company, diversified or otherwise, should be strongly centralized or decentralized. In all diverse organizations, there are certain basic functions which remain common (or central) to each element of the business, viz: Personnel Management Cash Management Taxation Management Legal Planning Accounting Standards It would follow that each of these common factors requires some supervision at a central level to ensure that overall group objectives are met. It is true that other functions including: Industrial Relations Marketing and Distribution Production Research and Development Purchasing Management Accounting may also be common to each element of the organization. However, there is far less commonality in the degree to which these functions are central to the efficient performance and financial well-being of the business. Role of Operating Units The resources of operating centers may be viewed as a bank of funds, the nature of which can be changed from time to time, but the employment of which must provide for ongoing increases in the net worth of the total enterprise expressed in terms of market values. Operating units are required to continually review products, methods, and opportunities and to monitor avenues for incremental investment--all with a view to attaining the necessary additive net present value of future cash flows of the enterprise. Operating units should be permitted sufficient autonomy to enable the best use to be made of the skills and experience of the people it employs in order to produce a return appropriate to the value of assets employed. Role of Head Office The head office will typically comprise a specialist group--the leaner the better if one strongly adopts the decentralist approach--often acting as Service Centers but also performing a control function in the corporate sense. The head office function is a cost center. It may be instrumental in developing strategies for increasing revenues or reducing costs on a group scale, but it does not generate revenue. Every dollar spent on this function is an extra dollar to be generated by the operating centers in order to achieve an increase in corporate wealth. TREASURY MANAGEMENT Treasury management is concerned with the provision of finance, cash-flow management, and risk analysis. Each decision taken within the enterprise has a cash implication. It follows that a well-integrated central Treasury function can, in all likelihood, produce economic benefits. The degree to which the function should be centralized depends largely upon the unique nature of the operating units it is servicing. Levels of ownership, the calibre of unit operating managers, and the nature and geographic distribution of the business are all factors determining the degree to which the Treasury function is centralized. In the case of Peko-Wallsend, the Treasury Department is small, comprising four people. While divisional cash-flow management is largely decentralized, Treasury is responsible for the daily management of funds surplus to the immediate needs of operating units. Treasury also operates as central banker and provides funds to

Jan 1, 1985

By E. P. Abrahamson

The effect of transition element binary solid solution additions upon the re crystallization temperature of nickel has been investigated. All additions raised the re crystallization temperature. Both the rate of change of re crystallization temperature with at. pet solute and the limit of initial linearity are found to correlate with the free atom ground state outer electron configuration of the solute element. A comparison of all of the correlations for the transition elements studied has yielded a set of empirical relations, which allows the prediction of the effect of dilute binary transition elements on the recrystallization temperature of other transition elements. The work of Abrahamson, et al.1-7 on dilute binary solution alloys indicated a correlation between the free atom ground state electron configuration of the solute and both the brittle-ductile transition and re-crystallization temperature. Further, it has been shown3,4 that the limit of initial linearity may also be correlated with the solute electron configuration. Since previous studies have dealt with bee and hexagonal base elements, this study is made to note what effect, if any, the fee base structure might have. Nickel also serves to give a solvent configuration which will allow the comparison of all of the transition element solvents. Olsen8 has studied the effect of some trace elements upon the recrystallization of nickel. He included only Ti, Zr, W, Mn, and Co of the transition elements. The differences in change of recrystallization temperature were attributed to the solute atom size and to the solubility of the solute in nickel. PROCEDURE All alloys were made using 99.9 + pet Ni with 0.003 C, 0.015 Fe, 0.007 0, and 0.0007 H. The solute elements were 99.9 + pet pure. According to the published binary phase diagrams9 and metallo-graphic examinations at X750, all solute elements were in solid solution. The alloys were arc melted and remelted four times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot forged at 800oC to 0.750 in. diam, machined to 0.60 in., vacuum annealed for 1 hr at 700°c, swaged to 0.40 in. and annealed at 700oC for 1 hr in vacuum. The grain size was checked and found to be 77 * 20 grains per sq mm. The specimens were then swaged to 0.187 in., yielding 76 ± 1 pet cold work. All alloys were then chemically analyzed for the solute addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The swaged rod was cut into 8.25 in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was maintained at 250" to 850°C over an eight inch length, recorded by twelve thermocouples. Control was ± 3oC, accomplished at the hot end. The recrystallization was determined metallo-graphically over the entire specimen. The criterion chosen was that point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be generally ± 3oC.

Jan 1, 1962

By A. H. Larson, R. J. McClincy

ALTHOUGH arsenic has a very high vapor pressure and vacuum distillation appears to be a likely method for its removal from lead, the published literature contains virtually no information concerning the vacuum removal of arsenic from lead. Caldwell, Spendlove, and St. Claire1 mention arsenic in their investigation of the removal of volatile metals from lead by vacuum distillation. They do not, however, give any data for arsenic removal or refer to any actual experimental work involving arsenic dissolved in lead. Moriyama, Kozuka, and Miura2 have determined the activity of arsenic in dilute As-Pb alloys in the temperature range from 450" to 600°C using a closed galvanic cell. They found that the activities of both arsenic and lead showed a positive deviation from ideality at 600°C. In view of the lack of experimental data regarding the vaporization of arsenic from As-Pb alloys, a limited vapor pressure study was made on liquid alloys containing from 0.5 to 3.3 wt pct As in lead at 703°C. The pressure of As4(v) above the alloys studied was determined from weight-loss data collected by means of the inert-gas saturation method. The experimental apparatus and procedure used were similar to that discussed by Alcock and Hooper9 with modifications as described by the authors., The technique involved was one of passing a known volume of inert gas over the alloy to be studied in a known amount of time and determining the loss in weight of the sample. Because of the low vapor pressure of lead at 703"C, the observed weight loss could be attributed solely to the vaporization of arsenic as the tetratomic molecule AS43 Measurements of the apparent vapor pressure were repeated at different inert-gas flow rates until from three to five values were obtained which were independent of inert-gas flow rate. This value of the apparent vapor pressure was taken to be the equilibrium vapor pressure of the alloy under consideration. The vapor pressures measured in this investigation have been converted to the activities of arsenic in As-Pb alloys, Table I, by use of the data compiled by Elliott and Gleiser5 for the vapor pressure of pure arsenic. The standard state for arsenic was chosen as the pure, hypothetical, supercooled liquid. The activity of arsenic was calculated from the fourth root of the ratio PAs,/PAS,. The low magnitude of the vapor pressures given in Table I explains the difficulty en- countered by earlier workers in successfully vacuum distilling arsenic from very dilute As-Pb alloys. The data shown in Fig. 1 indicate that the As-Pb system behaves ideally. The apparent outlier represented by the alloy containing 1.43 mol pct As is a result of the fact that the pressure of As, above the alloy was barely detectable by the experimental procedure used in this investigation. Because of this, the apparent vapor pressure determined for this alloy could be in considerable error. Moriyama, Kozuka, and ~iura' have reported that arsenic shows a positive deviation from ideality in dilute solution in lead. However, details of their results have not been made available. This research was made possible by a grant from the National Science Foundation (GK-196) for which the authors are very appreciative.

Jan 1, 1970

By H. I. Meyer, D. F. Searcy

INTRODUCTION The analysls of our previous paper' on the behavior at two immiscible fluids separated by gravity into two dlstinct saturated zones in the porous medium was shown to be theoretically valid only if one of the two fluids was immobile. The practical problems associated with flow of both phases have so far been impossible of solution by these analytic methods. We, therefore, decided to resort to a simulator study to answer the following pertinent questions: 1. If the lighter fluid is produced from a point above the fluid-fluid interface, how long will it take for the heavier fluid to come up to the point where production of both fluids is taking place? 2. After steady-state two-phase production is established, what is the relative production rate of each phase, on what physical variables does this depend, and what are the boundary conditions at the outflow face? 3. A third question was at least partially answered in the course of this investigation: that of the shape of the interface under flow conditions. These questions are of fundamental importance in the fields of hydrology and the reservoir mechanics of oil and gas production. In order to simplify equipment used and still retain a fair physical representation of these phenomena, it was decided to use a Hele-Shaw type of analogy in which the flow took place between two vertically mounted pieces of plate glass. The advantage of this system is that it eliminates any surface effects between the matrix of the porous medium (e.g. packed sand) and also allows equilibrium conditions to be established more quickly. The principle disadvantage (apart from the obvious one of being one more step removed from the prototype) is that our equipment limited us to two dimensional flow studies. In spite of these limitations answers to the questions were obtained which seem adequate for our purposes. We would like to see more work of this nature done to verify and to improve our conclusions. DESCRIPTION OF EQUIPMENT AND PROCEDURE A drawing of the equipment used in this study is shown in Fig. 1. Fluid flow takes place between the two 36 in. x 12 in. pieces of plate glass held apart at the long edges by two spacers of cellulose acetate sheet (Kodapac IV) which is available in several thicknesses. This sandwich was clamped together by small c-clamps whose stress was distributed by long pieces of 3/8-in. keystock. Accurate spacing was obtained by tightening these clamps as indicated by micrometer measurements on the outside of the glass. At the upstream end of the plates a piece of 6-in. diameter pipe simulated an infinite reservoir, while at the downstream end a 2-in. Lucite cylinder with a small hole near the top of the flow region served to drain the fluid. Sealing was achieved by O-rings, the whole system being tightened by pressure on the Lucite tube provided by set screws (not shown in the drawing). The total head

Jan 1, 1957

By W. M. Lehrer

RECENT development of high-temperature brazing alloys has required information regarding the eutec-tic temperature and composition of the Pd-rich section of the Pd-B system.. Literature on this subject was found to be scanty with no complete system yet determined. Buddery and welch1 report an inter-metallic compound occurring in the Pd-B system at 6.33 wt pct B (PdsBz). Another source, Sieverts and Bruning,2 indicates that after annealing at 700°C, a 1.6 and a 2.0 wt pct B alloy were two phase whereas a 0.75 pct B alloy was single phase. Recent work3 using a hot-stage microscope has proposed a eutectic temperature of 743OC. This method utilized the observation of the onset of incipient melting at grain boundaries. The eutectic composition, however, was not determined. METHODS AND PR0CEDURES Five alloys were prepared by triple inert arc-melting high-purity palladium (95.98 pct) with additions of 2 to 6 pct purified amorphous boron. The alloys were crushed within a hardened steel mortar with a steel pestle. The 2 pct alloy, however, was too tough to be crushed in the above manner so was crushed by successive reductions through a rolling mill. Approximately 17 to 18 g of the crushed alloy was used in the thermal analysis. The alloys were melted in pure quartz crucibles. The thermocouple protection tubes were also of quartz and fused along the inside wall of crucibles to prevent floating of the thermocouple. This was an expediency as centering of the thermocouple in the melt would have been preferable. Melting was done in a tube furnace with a slow flow of tank helium maintained as a protective atmosphere. Heating and cooling rates were maintained at 3.5OC per min through the critical temperature ranges by means of a synchronous motor hook-up to a furnace controller. All specimens were heated to 100°C over the indicated liquidus on heating prior to reversing to the cooling cycle. Specimens emerged from the furnace with mirrorlike brightness attesting to the protective quality of the helium atmosphere. Thermal arrests were detected by the differential thermocouple technique using chrome l-alumel couples and nickel as the reference specimen. Arrests were recorded on a Leeds-Northrup automatic X-Y recorder. The specimen temperature and temperature difference were read to + 7.5OC and ± 1.5OC, respectively. These readings were well within the sensitivity of the instrument amplifier. Chromel-alumel couples were used in lieu of Pt-Rh as very few arrests were contemplated in excess of 1200" to 1300°C, the approach of instability. No standardization was performed on these thermocouples subsequent to their use. RESULTS The thermal arrest temperatures obtained are plotted in Fig. 1 as a function of wt pct B. The composition function was obtained by chemical analysis of portions of the specimens after the thermal analysis was completed. The 2 to 6 pct nominal alloys were found to have 1.80, 2.35, 3.65, 4.18 and 5.90

Jan 1, 1960

By William B. Senseman

FOR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system, and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt. at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low,, the heat obtained from the conversion of mill power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1945

This volume summarizes characteristics and the geological setting of porphyry copper deposits of the Western Hemisphere. Grouped by characteristics, porphyry copper deposits are described in six regions: Andean orogen, Appalachian orogen, Alaska, northern Cordilleran orogen, southern Cordilleran orogen, and the Caribbean. Each region has its own peculiarities of geologic setting, and those deposit characteristics that may be projected from one chapter to another will be used in reaching the conclusions from which to draw genetic models for porphyry copper deposits. The term porphyry in this volume denotes a type of ore deposit, rather than a rock classification. The classification of intrusive igneous rocks used in this volume is shown in Figs. 36a and 42 (pp. 103, 130). Some modern classifications suggest mineral-ratio definitions other than those used in this volume; however, most literature references cited are based on the classification shown in Figs. 36a and 42. The reader should be aware, therefore, that quartz monzonite in this volume contains from 35% to 65% potassuim feldspar and at least 10% quartz. A term used in this volume is defined where introduced within the context of a specific chapter. Distensional tectonic conditions are used in the sense of Cady (1972) in the Appalachian orogen, for example. Porphyry copper deposits are defined as large bodies of mineralized rock, usually including a porphyritic intrusive phase, that have copper sulfide minerals disseminated through them. The definition has no commercial connotation and is used strictly in a noneconomic sense to encompass the spectrum of copper mineralization associated with these deposits. Terms commonly accepted in the literature are not defined. Porphyry molybdenum and porphyry copper deposits commonly are distinguished by most economic geologists. The basis for the separation is summarized in one chapter of this volume. To permit the reader to more easily peruse the bibliography for any particular region, references will be found at the end of each chapter. The bibliography is not intended to be complete, but is designed to provide adequate minimum coverage for descriptions of deposits in the chapter concerned. Each entry is properly referenced in the text of that chapter to facilitate the reader's research into any particular topic. This volume is written from the point of view of the exploration geologist whose task it is to evaluate the structural, petrographic, mineralogic, and metallogenic characteristics of a porphyry copper deposit. The goal of the evaluation is to determine if, and where, concentrations of metals may exist in an igneous- hydrothermal system that includes the most complex set of geologic factors found in any of the many types of ore deposits. The successful porphyry copper geologist is simultaneously a petrographer, geochemist, structural geologist, and mineralogist. Some porphyry copper deposits have developed in volcanic arcs underlain by a Benioff seismic zone with a trench paralleling the arc. The most convincing example of a deposit known to have developed in an environment where subduction is an active process is the 3.3 m.y. (million years) old Dry Creek occurrence in the Aleutian arc (this volume). On the other hand, the younger deposits in the Cascades appear to have formed in a volcanic arc lacking both the Benioff zone and the offshore trench. Subduction is not widely accepted as an active mechanism for the period when the younger Cascade deposits formed. Subduction has also been questioned for deposits formed at a great distance from a plate boundary (e.g., Bingham). Regardless of the pros and cons regarding subduction, most deposits are associated with regional faults. Strike-slip

Jan 1, 1978

By C. H. Ma, J. S. Makris

This paper describes a modified X-ray diffraction microscope wzethod based on the general principles of Berg-Bawett's Method, Lang's Method, and Woosters1 Technique. This new method may be used for stationary or oscillatory photomacrographs, with both reflection and transmission techniques. In the stationary technique, a small point-source of a divergent X-ray beam of white radiation is used; in the oscillatory technique, a monochromatic divergent beam is employed. The chief advantages of the method described herein are that only approximate alignment of the Bragg angle -of-interest is needed during exposure, and that a large portion of a crystal-specimen surface can he irradiated. In recent years, the study of dislocations through X-ray diffraction microscope techniques has received considerable attention as concerns the per,fection of single crystals. Very promising results have appeared in the literature.'-' These techniques are very useful when the dislocation density of a crystal is near 105 per sq cm or lower. The principle of X-ray diffraction microscopy is based on the differential effect of X-ray primary extinction between the distorted parts and the perfect parts of a crystal. When an X-ray beam impinges on a set of planes of a crystal at the correct Bragg angle, diffraction of X-rays will occur with a 90-deg phase shift of the diffracted beam. This once-diffracted beam still forms the correct Bragg angle with the planes ahead of it, if the planes are not distorted. Thus, part of the strength of the once-diffracted beam is rediffracted and the beam continues to travel in the direction of the primary X-ray beam. This twice-diffracted beam not only takes away part of the strength of the once-diffracted beam, but also causes destructive interference with the primary beam because it now is exactly 180 deg out of phase with the primary beam. As the primary beam goes farther and farther into the crystal, its intensity is continuously weakened. Asa result, the ultimate X-ray diffraction power of a set of undistorted planes is largely extinguished. This phenomenon is called primary extinction.1,2'4 If the set of planes ahead of it is distorted, the once-diffracted beam will have less chance to be rediffracted, because it could not meet the exactly correct Bragg angle for rediffraction. If a part of the beam does rediffract, this twice-diffracted beam is not exactly 180 deg out of phase with the primary beam, and thus it causes less destructive interference. As a result, the registered X-ray diffraction power of the distorted part of a crystal appears stronger than that of the perfect part. Thus, point-by-point contrast of a diffraction image is theoretically possible from a crystal containing dislocations. Two most popular X-ray diffraction microscope techniques today are Berg-Barrett's Method and Lang's Method. Both of these techniques require a

Jan 1, 1964

By James B. Macelwane

THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these 'fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the. January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1952

By Lester C. Uren

THIS paper reviews the industrial trends and changes in educational concepts that have led to the development of the modern petroleum engineering curriculum. A trend toward emphasis on engineering fundamentals is noted. While most universities are committed to the traditional four-year engineering program, it is agreed that more than four years is necessary for academic preparation of the petroleum engineer in all phases of his profession. The author proposes a coordinated program of undergraduate and graduate training that will permit of adherence to the general pattern of the present four-year engineering course, with provision for extension of the program into specialized graduate courses of professional character. In the latter, emphasis may vary with the interests and objectives of the individual student. A specific undergraduate curriculum is proposed in which upward of 80 per cent of the available time is devoted to engineering fundamentals. A broad survey of the professional field is afforded in courses grouped in the third and fourth undergraduate years, but detailed treatment of the professional aspects of petroleum engineering is reserved for the graduate program. INTRODUCTION Of necessity, engineering curricula must ever be changing to reflect the new techniques, the changing concepts that are presented as the engineering industries develop and unfold. Particularly is this true of the younger engineering curricula representing comparatively new and rapidly changing industries such as the petroleum industry. Institutions that planned their petroleum engineering curricula a decade or two ago now find that the petroleum industry has become vastly more technical in its requirements. Entirely new methods and techniques have come into vogue and must be given place in the curriculum, and some of these are of a character that demands changing emphasis in the fundamental preparatory subjects. College and university faculties cannot complacently assume that curricula in this field that were considered appropriate 10 or 20 years ago still reflect the needs of the industry that they are designed to serve. If they do, their graduates will be poorly equipped to meet the requirements imposed upon them by a rapidly changing industry. Perhaps it is not too much to expect academic authorities to anticipate the trends of industry and equip their graduates with what they will need to attain leadership 10 or 20 years after graduation. Whether or not this desirable objective is possible, there is no excuse for allowing curricula to fall behind the current needs of industry. DURATION OF CURRICULUM The majority of our engineering schools and colleges still adhere to the four-year curricula and there appears to be a definite - sentiment among many engineers engaged in industry that work should be so planned that the engineering student may secure the essential academic preparation for his profession in a terminal four-year program. Yet, in recent years, it has become increasingly apparent that four years of

Jan 1, 1941

By J. D. Forrester, Erich Sarapuu, T. C. Cheasley

John G. Tripp-—The concept of converting fuel deposits in-situ to useful forms of energy and chemical raw materials has important possibilities as a means of stretching out our fuel resources. The authors have worked in this field for years and in fact are among the pioneers in developing in-situ techniques based on underground electrocarbonization. Their efforts have aroused great interest in this subject and their contributions will undoubtedly gain even more significance as time goes on. The 4 to 5 billion tons of petroleum are proved reserves, that is, they are completely defined and could be produced economically with present methods of recovery. Reserves of coal, tar sands, and oil shale shown in Table I are not equivalent to proved reserves as the term is used in the oil industry. Incidentally, the 4.3 billion tons of oil shown in the tabulation is equal to about 28 billion barrels of oil and, therefore, presumably does not include reserves of natural gas liquids estimated at about 5 billion barrels. The relative comparisons would be more complete if these liquids together with the reserves of natural gas were included in the tabulation. It is stated in the report that production costs of the order of 10c per million Btu's could be expected from a large industrial electrocarbonization installation. The authors state that the operation probably could be operated successfully and at a profit. I would like to express my view that for the operation to be profitable extremely favorable conditions would have to prevail. For example, the coal seam would have to be thick and close to the surface in order to minimize drilling costs; the deposit should be dry and so situated that there would be little, if any, inflow of ground water; and the seam would have to be relatively gas tight to avoid excessive gas leakage. Notwithstanding the tremendous strides that have already been made, it is my hope that the authors plan to continue their development work. Experiments on underground electrolinking and initial carbonization at Gorgas, Ala., indicate a need for improved control over the operation. Subsequent examination of the underground system at Gorgas has shown that the gasification zone did not always follow a direct path between the electrodes. Undoubtedly the control of the in-situ thermal processes can be improved by further development work. With respect to the electrocarbonization of oil shale it may be well to point out that the cost of mining oil shale is estimated to be 50c to 60c per ton. These are low mining costs as compared to coal. Thus it would appear that there is less economic incentive for applying in-situ thermal methods to oil shale than there is for applying these methods to coal. As is the case with in-situ methods for petroleum, the product from the shale having the most economic interest would be liquid oil rather than gas. The authors point out that for distances up to several hundred miles it is cheaper to transmit energy as electricity than it is to ship energy as coal. This is a very important point, and with coal shipping rates rising periodically, it could prove increasingly important in the future. I believe that the authors deserve great credit for their outstanding work on underground electrocarbonization. The knowledge resulting from their efforts is of great value to our fuels technology. James L. Elder—The experimental work conducted by the authors on the electrolinking-carbonization of carbonaceous materials in situ is of great interest. The method is of great importance in the development

Jan 1, 1955

By L. C. Armstrong

Twice in the past two years and in two widely separated localities—ane near Williamsville, Mo., and the other in the Allard Lake district of Quebec— the Contract Drilling Division of the Longyear Company has experienced perplexing difficulties in drilling granitoid igneous rocks. The rocks in both places are characterized by appreciable amounts of feldspar intimately inter-grown with quartz particles of microscopic dimensions. The disappointingly slow rate of advance and the exceptionally high bortz loss, obtaining during the life of these two projects, are ascribed largely to the resistance to abrasion of these two minerals when arranged in this intergrown pattern. Whether all intergrowth-bearing igneous rocks would offer extraordinary resistance to bit progress cannot be stated with assurance on the strength of these experiences alone. More data on diamond drilling this sort of material in a number of localities are needed before any generalizations can be made safely. It should be pointed out that the lack of time and funds made it impossible for the writer, or other persons interested in correlating the details of bit histories with the kinds of rocks drilled, to be present during the performance of the contracts. However, the records kept in the normal course of drilling are deemed complete enough to be reportworthy. This information is presented here together with the findings made in studies of the rocks involved, with the thought that it may attract the comments of others who may have encountered similar refractory drilling conditions. A pooling of knowledge on the problem would be of material aid in devising more efficient cutting tools and procedures for penetrating this kind of rock. Drilling Blastholes in the Williamsville Granite Due to the unsatisfactory perform- ance of pneumatic percussion drills in boring blastholes on a construction contract near Williamsville, Mo., tests were made with a diamond drill. The poor progress achieved and the excessive loss of diamonds, however, soon led to the abandonment of these trials. The diamonds, in all of the bits tried, lost their cutting edges and acquired a polish after being in service for distances ranging from a few inches to a few feet. Coring bits containing surface-set, whole-stone bortz in a tungsten powder matrix were employed. The cost assignable to bortz wear averaged $7.17 per foot. This item of expense is several times the amount normally expended in diamond drilling in firm, unfractured, granitic rocks. Diamond-impregnated, tungsten carbide bits also were used without success. The diamond wear was at the rate of $0.98 per foot, but the diamond chips became too polished for further duty in less than a foot of drilling. The Williamsville granite is pink and medium-grained. In the hand specimen, it has a fresh, sound appearance; it is seemingly composed almost entirely of interlocking grains of feldspar and quartz and has no discernible features suggesting a greater durability than is usually found in rocks with this composition and texture. Microscopic examination, however, reveals a predominance of feldspar grains with more or less regularly distributed and sharply angular masses of quartz (see Fig 1). The pattern assumed by the two minerals in this mode of occurrence is referred to as a "graphic intergrowth," as it bears some resemblance to the cuneiform characters of ancient Persian writing. The other principal constituents are quartz-free feldspars (microcline and orthoclase) and quartz. All of these constituents are in nearly equidimensional grains, ranging up to about 3 mm in length. There are also

Jan 1, 1950

By Leonard B. Lipson

Boyer, Morgan and Muskat,' with improvements by Morgan, McDowell, and Doty,l and Laird and Putnam,' have described a scheme for the determination of fluid saturatic in porous media by measuring the x-ray linear absorbing power of particular fluids in the media. This method is one of several which depend on the linear absorbing power of the fluids in the porous medium. Other examples of linear absorption methods involve measurement of dielectric constant, gamma ray absorption, and ultrasonic attenuation. It is the purpose of this note to demonstrate by theortical considerations that the absorption versus saturation curve for a linear absorption method is not necessarily a single valued function of the saturation. Such non-unique behavior must be considered and evaluated before suitable saturation determinations can be made by a linear absorption method. To illustrate the discussion, examples will be given only for the simplest cases of combinations of two different dielectrics. The dielectric constant method was chosen for illustration because it was thought to demonstrate most graphically the point in question. According to Argue and Maass,4 the resultant dielectric constant of a combination of two different dielectrics depends on the orientation of the dielectrics in the electric field of the test condenser used to measure the dielectric constant. One ease involves alternate slabs of dielectrics E1 and E2 perpendicular to the electric field of the test condenser, as shown in Fig. 1A. For this case: l/'E, = A/E, + B/E,.......(1) where E,,, is the dielectric constant of the combination, A is the ratio of the path length through dielectric E, to the distance between the plates of the condenser (assuming the dielectrics have the same cross sectional area as the condenser), and B is the ratio of the path length through dielectric E2 to the distance between the plates of the condenser. It will be noted that the constants A and B are numerically equal to the fractional "saturation" of the region between the test plates of the condenser by the two dielectrics E1 and E2, respectively. Another case involves alternate columns of the two dielectrics parallel to the electric field and forming a continuous path between the condenser plates, as shown in Fig. 1B. For this case: E., = AE1 + BE2.........(2) where E., is the dielectric constant of the combination, A is the ratio of the cross sectional area of dielectric E, to the cross sectional area of the condenser plates (assuming the lengths of the dielectrics equal the distance between the condenser plates) and B is the ratio of the cross sectional area of dielectric E2 to the cross sectional area of the condenser plates. As before the constants A and B are the effective "saturation" of the condenser by the two dielectrics. Still another case is described by Lichtenecker5 where dielectric E2 is shown in the form of small particles distributed at random in dielectric E1. This is shown in Fig. 1C. For this case: log Em = A log E1 + B log E2.....(3) where Em is the dielectric constant of the combination. A is the ratio of the volume of dielectric E1 to the volume of the condenser, i.e., the effective "saturation" of the condenser by dielectric E,. B is the ratio of the volume of dielectric E2 to the volume of the condenser, i.e., "saturation" of dielectric El. Equations (l), (2) and (3) are plotted in Fig. 2 for E1 = 2.5 (oil) and E2 = 80 (water). Equations (1) and (2) may he thought of as representing the limiting cases of the configuration of two fluids which might be expected to exist in a porous medium. Equation (3),

Jan 1, 1951

By W. Philippoff, Donald E. Cadwell, S. R. B. Cooke

THE importance of contact angles in flotation has long been recognized, but little has been done to get quantitative relationships between the surface coverage of the mineral by the reagent, the length of the hydrocarbon chain, and the contact angle. It is well known that for a complete monolayer on the surface of a mineral the contact angle 8 is determined only by the reagent1 and principally by the chain length of the hydrocarbon radical. Although for flotation the monolayer usually is regarded as being complete, early experiments of Wark and Cox&apos; showed that at very small concentrations of potassium ethyl xanthate the contact angle on galena changed in a continuous way from 0&apos; to the equilibrium value of 60". Further, Gaudin and Vincenta showed a similar continuity using heptylic acid and sphalerite. This shows that with probably incomplete monolayers, 0 varies with the degree of surface coverage. At the time these experiments were made it was impossible to measure the actual amount of surface coverage, especially since the decrease of the collector concentration in the liquor could be influenced by chemical side reactions. Through the use of the radioactive tracer method for the measurement of the amount of collector adsorbed on the surface of the mineral, Gaudin and Bloecher&apos; were able to determine accurately the actual surface coverage of dodecylamine acetate on quartz, but they did not measure any contact angles. It is believed that the relationship between the surface coverage and the contact angle is extremely important in flotation, especially as Gaudin and Bloecher showed that a 95 pct recovery is possible with a coverage of only 5 pct. Theoretical Considerations The work of adhesion W is the energy bound (in ergs per sq cm) when an interface is formed. It is determined by the difference of the free surface energies (surface tensions) of the respective phases 7j and yZ before contact and the interfacial free surface energy y, after contact. The definition of the contact angle permits the elimination of the unknown surface energy of the solid and hence the calculation of W from the surface tension of the liquid y and the contact angle 8: W = y (1 + COS0) [1] Consider a surface consisting of two components, identified as 2 and 3, 1 being the liquid. The amount of 2 in the composite surface is x, where 0 < x < 1. The respective contact angles with 1 and air are 8, and 8.. The total work of adhesion of such a surface is the sum of the values of the components multiplied by their respective areas. A formal relation can be written: Wm = x-W2+ (l-x)-W, [2] in which W, is the work of adhesion of the composite surface. Eq 1 can be introduced into Wt and Wa, but in the case of W, some discussion is needed. If the two components are segregated, each component forming an integral part of the composite surface there is no physical meaning for a contact angle 8m calculated from W,, by using eq 1. If, on the other hand, the area of each patch of the components is small in comparison with, say, the diameter of the bubble used in measuring, it could be expected that 0m would have a physical significance, because of the action of the surface tension of the liquid-gas interface tending to smooth out sharp corners. How small these patches would have to be is difficult to predict, but by using composite surfaces with microscopically

Jan 1, 1953

By Norman F. Schulz, Emert W. Lindroos, Strathmore R. B. Cooke

DURING the course of an investigation of the effects of various starch products on hematite and quartz in regard to their separation by flotation, it was found that whereas most starches flocculated suspensions of hematite in water, they did not flocculate similar suspensions of quartz. However, a derivative of whole corn starch containing approximately one tenth aminoethyl group (-—CH,CH2NH2) per glucose unit proved to be an exception. This aminoethyl starch was a very good flocculant for both hematite and quartz, and also possessed the property of depressing both minerals in cationic flotation tests. In view of the widespread use of starch as a flocculating agent of solids in tailing water, pulps, and for coal slimes, ore and various other purposes in sulphide and nonsulphide flotation, attention is called to the effective surface activity of aminoethyl starch in flocculating suspensions of the two minerals investigated. Test Materials The starch products employed included Globe Pearl starch No. 144 and fresh aminoethyl starch, both supplied by the Corn Products Refining Co. Dr. A. L. Elder" has kindly furnished a description The minerals used in the various tests are listed in Table I. Their specific surfaces were determined by the air permeability method, which gave results reproducible to within plus or minus 3 pct. Surface areas obtained by krypton adsorption were greater than the air permeability values by a factor of 2.0 for quartz and 62.4 for hematite. Starch Adsorption on Mineral Surfaces Starch adsorption data were obtained by agitating for 1 hr measured volumes of neutral starch solutions of known concentrations with weighed quantities of finely divided mineral of measured specific surface. The mineral then was separated from the pulp liquor by centrifugation and the residual starch content determined by chemical analysis. The analytical procedure consisted of oxidizing the starch with an excess of dichromate in acid medium at elevated temperature and titrating the excess dichromate by the ferrous ammonium sulphate—potassium permanganate method. Analytical results were reproducible to within less than 1 pct. Adsorption data obtained in unbuffered solutions near the neutral point are plotted in Fig. 1. The adsorption on either mineral was far greater for the aminoethyl starch than for the Pearl starch. Flocculation The degree of flocculation was determined for a given pulp by measuring the time required for the supernatant liquid to reach a certain degree of clarity. This was accomplished by passing a standard light beam through the pulp, contained in a glass settling tube, and measuring the time required after agitation ceased for the intensity of the transmitted beam to reach a predetermined value. Starch reagent was added to each pulp in small uniform increments, and the settling time was determined after each such addition. Increase in pulp liquor volume due to the added starch reagent was ignored in these tests. Pulps were maintained at or near neutrality. of the preparation of the aminoethyl starch: "Three hundred and sixty grams of powdered unmodified corn starch was slurried in 3 liters of water and stirred during gelatinization. Eighty-six grams of ethylenimine was added slowly during reflux which was continued for 4 hr. The yellow solution set to a gel upon cooling. This was broken up and neutralized with HC1. The thick paste was dried on hot rolls. Adsorbed polyethylenimine and salts were removed from the yellowish products by washing first with acidified aqueous &apos;60 per cent&apos; alcohol. The white product contained nitrogen corresponding to about one aminoethoxy group per ten glucose residues." Only laboratory samples of this starch derivative have been prepared. The starch reagents for use in flocculation, flotation, and adsorption tests were made up by dispersing the appropriate quantities of air-dry starch in cold water, adding boiling water, and heating for 30 min at 120°C under pressure. When used ip adsorption tests, the starch solutions first were cleared of insoluble matter by centrifugation.

Jan 1, 1953

By J. B. Macelwane

Historically whenever application of scientific results to a new problem required the special experimental background, the economic outlook and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering based on the professional requirement grew up in the engineering colleges. This is precisely what is happening now in geophysical engineering. THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1953