Search Documents

By W. D. Donnelly, M. L. Rudee

THE crystallography and morphology of ?-Al3Fe precipitates in an A1 + 0.5 wt pct Fe alloy have been studied by transmission electron microscopy. The alloy was cast in cylindrical ingots, 15 cm in diameter and 60 cm in length, and cooled slowly. The measured composition was 0.527 wt pct Fe, 0.001 wt pct Mg, and 0.003 wt pct Cu. Spectrographic analysis revealed no additional trace impurities. Thin slices were cut from the ingot and reduced by more than 95 pct by rolling to a thickness of 0.1 mm with no intermediate annealing treatments. These thin sheets were then vacuum-annealed for 1 hr at 612°C and air-cooled in their capsules. Thin foils for examination in the electron microscope were prepared by electropolishing. The precipitate is found in the form of oval platelets on the (110) planes of the matrix. The major axes of the platelets are parallel to the (110) directions of the matrix, and vary in length from 1/2 to 2 p. The thickness is about 1/10 µ. Examples of platelets, both in the plane of the foil and normal to the foil, are shown in Figs. l(a) and l(b), respectively. lack' found that ?-A13Fe (more correctly Al13Fe4) belongs to the monoclinic system. Using Black's structural data and simultaneous electron-diffraction patterns from the matrix and precipitates, the habit planes and directions were determined to be: (001)? 1 (110)Al [100]?|| H [001]Al The orthogonal crystallographic axes of the precipitates are accurately in the habit plane, while the measured coincidences of the directions are only within 10 deg. The major axis of the platelet is parallel to [010] in the 0. This orientation corresponds to the direction of nearest registry of the lattices.

Jan 1, 1964

By George Laird

IF IT IS true that Sir Walter Raleigh lost his head for his failure to find gold in the Guianas, the trumped up charge of "treason" might better have been "con-tributory negligence." That systematic investigation and development of the gold-bearing areas of both Dutch and French Guiana have not been accomplished is not due so much to the lack of gold as to the geo-graphical, physical and climatic conditions of the two colonies. The Dutch, as a people, are not prospectors. The French look upon "Cayenne," or French Guiana, as DJOEKA BOATS USED IN RIVER TRANSPORTATION. just what it is: a penal colony, which produces a certain amount of balata, gold and essential oils, all of which can be purchased from the natives with far less physical exertion than they can be secured from the "bush" or jungle. The colonies have had their gold "booms," and dur-ing these periods the production has increased to a considerable amount, but the hardships to be endured in reaching the fields, the cost of transporting tools and supplies, the ever-present fevers, the bite of the "57 varieties" of insects and, lastly but not leastly, the abundance of rum in the seaport towns, dampen the ardor of even the strongest; the production of gold is left to the "pork knocker" or illegal gold digger and to the comparatively few producing "mines."

Jan 10, 1922

Dr. Arthur H. Elliott has been connected with the gas industry for upward of thirty-eight years and was a chemist to whom the industry is deeply indebted for the application of the science of chemistry to its problems and processes. He was born in London, England, in 1851, and was the son-of a physician. While a child he was taken to France, where he received his early education, learning to speak the French language before his native English. His father having destined him for the medical profession, he commenced his studies on his return to England, but his attention being attracted to chemistry, he gave up the study of medicine to pursue that of chemistry. While still a student, he obtained a reputation as an iron and steel analyst, publishing two methods of analysis, one for the determination of sulphur .and the other for the determination of carbon in cast iron. On his graduation from the School of Mines at South Kensington, he left England intending to go to Australia, where an uncle resided, having in mind also the possibility of a trip to China. On his arrival in New York, he met Professor Charles F. Chandler, to whom he had a letter of introduction, and who induced young Elliott to remain. He graduated from Columbia College with the degree of Doctor of Philosophy in 1883. He became demonstrator in chemistry at the College of Pharmacy and afterward professor of chemistry and physics at the same college. He became connected with the Municipal Gas Lighting Co. in May, 1880. In. November, 1.884, when consolidation took place, he became engineer-chemist of the Consolidated Gas Co., which position he held until May, 1910, when he resigned, but was retained as consulting chemist until his death. Recently Columbia University conferred on him the honorary degree of Master of Science.

Jan 7, 1918

In his paper, Sastry proposes the use of flotation methods other than the "conventional flotation!' process as possible economical methods of removing mineral fines, The practice of Liquid/Solid separation employing microbubbles to assist or induce the flotation of suspended solids is common to both municipal and industrial waste- water treatment; and is also used as a separation step in some processing industries. The pretreatment (if any) of the stream prior to flotation, the source of the microbubbles, and the design of the separation vessel depend on the application. For example: a metal finishing plant would use an elaborate chemical conditioning scheme to precipitate metal hydroxides for removal by a dissolved air flotation unit operating in the effluent recycle mode, while some oily waste can be separated using a dispersed air flotation cell with no chemical conditioning. At the present time, the "conventional flotation" process employed by the mineral processing industry makes use of mechanical agitation and aeration to generate certain sizes and quantities of bubbles and to mix these bubbles with the pulp. Specific types of chemical conditioning are used to obtain the desired results. For the separation of mineral fines, the type of chemical conditioning, bubble generation and separation device needed to obtain optimum results will have to be determined through research. The point to be made is that while the principles of flotation separation can be applied to a wide variety of applications, the specifics of the flotation process may vary with each application. Sastry's paper has dealt with the many areas of research required to fully understand and utilize the flotation process for the beneficiation of mineral fines.

Jan 1, 1979

By Gerhard Derge

A SERIES of studies of the corrosion of tin is under way in the Metals Research Laboratory at the Carnegie Institute of Technology. The complete program includes examination of the corrosion properties of high-purity tin and the changes produced in these properties by the addition of varying amounts of alloying elements. Other studies of this subject have been made recently under the sponsorship of the Inter-national Tin Research and Development Council, but these researches have been confined largely to the weakly acid environments commonly encountered in the canning industry.1 There is little information avail-able regarding the corrosion of tin under alkaline conditions, but such data would be of value, for a large amount of the metal is used under such conditions. The potential measurements to be described were made because they seemed to offer the most rapid method for obtaining a general view of the conditions to be encountered in such service. These experiments will also serve to establish a technique that will be of value in further studies. It must be emphasized that the results reported are those of controlled laboratory experiments and that the conclusions drawn cannot yet be applied to service conditions; rather, they point to the directions in which, more exhaustive experimental work may be clone to best advantage.

Jan 1, 1938

By T. F. Witherbee

(Read at the Amenia Meeting, October, 1878.) As the forms of blown-out furnaces are of much interest to iron-masters and metallurgists, the manner of taking the accompanying sections of the Cedar Point stack is here given. The diagrams show the original and also the final shape of the furnace after a two years and twelve days' blast, during which the following solid materials passed through it, viz.: Coal, 41,000 tons; ore, 57,000 tons ; limestone, 30,000; total, 128,000 gross tons. Product, 41 1/4 tons per day Bessemer pig iron. The apparatus used in taking the sections was a modification of that proposed by Mr. Frank Firmstone,* and consisted of a sliding rule, to follow around the circumference of the stack, which rule was connected by a string to a segment of a circle of 24 inches radius. The segment was carried by an arm which connected it to a hub as a centre, 2 inches in diameter. A second string was wound around the hub, and communicated motion to a pencil-carrier, the pencil of which marked out on paper the exact outline, and reduced it to a scale of 1/2 inch to the foot. The whole machine was made in about three hours, with the facilities of a carpenter's shop, and gave in operation every irregularity of the lining. The sections were taken at salient points, by lowering a hanging staging on which the apparatus was placed. Tracings from the paper of the machine were made, and, as in this case several copies were required, the tracings were glued on to thin sheets of basswood, and patterns carefully sawed out with a bracket saw. * Transactions, vol. iii, p. 106.

Jan 1, 1878

By R. F. Shurtz

This note calls attention to a contradiction in current eatistical theory and to corresponding difficulties in practice. These are significant concern in evaluating almost all ore deposits. The theoretical contradiction is that the commonly used spherical model for the semivariogram is not consistent with the usual definition of a "regionalized variable" as a mathematical function, the direct study of which "is excluded because its spatial variability is usually extremely erratic, with all kinds of discontinuities. . ." (Journel and Huijbregts, 1978). Specifically, this means a grade function that is too "rough" for interpolation to be useful. The practical difficulty is that the spherical semivariogram interprets the data upon which it is based in a manner that is, more often than not, demonstrably inconsistent with reality. This is attributable to the widely disregarded interaction between the sample pattern and the grade function. Each sample pattern "blurs" the grade function in its own particular way. It is as though the grade structure of the deposit were seen through a lens of poor resolution or reflected in a warped mirror, such as those found in amusement parks. The fitted spherical model embeds this sometimes dangerously blurred and distorted image in the Krige regression. A full analysis of these inconsistencies is to be presented later but, in the meantime, it seems urgent to communicate their effects so that those engaged in estimating ore reserves may be on guard. The spherical semivariogram has a sill and can be replaced by the corresponding covariogram. The equation of the spherical covariogram in normalized form, that is, variance and range both equal to one, is represented as: [ ]

Jan 1, 1984

The Library of the above-named Societies is open from 9, A.M. to 10 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special, attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that, the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library y forwarding copies of mining reports, maps privately issued, and similar material, which will be classified; indexed, and made availableto other members. Suggestions for additions to the Library, either y purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 8, 1914

By Tuncel M. Yegulalp, Malcolm T. Wane

In general, many problems relating to the exploitation of mineral deposits are probabilistic in nature. This derives from the fact that the geologic universe is inherently random. Probability theory and statistics have been found useful for forecasting the behavior of natural events that occur in the geologic universe. The objective of this paper is to outline the application of the theory of extremes to this forecasting problem. Consider the design of an underground structure or the design of a rock slope. The initial step is the formulation of the various possible structural actions which result from the geometry of the layout. For a given structural model, various intensities of behavior are possible depending upon the load, deformation, and material characteristic spectra, respectively. Of popular interest to mining people is the failure behavior or condition. A necessary feature of the analysis is the rupture strength of the material. Information on the rupture strength is derived from testing either in situ or in the laboratory and the usual outcome is a variation in the test results. This variation is overcome by constructing a frequency distribution of rupture strengths, and then determining a measure of central tendency and variability. The main feature of interest in the analysis is the failure characteristic and its percentage chance of occurrence. Hence, one is naturally led to examine those areas of a distribution curve which are termed the tails. The statistical concepts which can most efficiently handle such areas are contained within extreme value statistics.

Jan 8, 1969

By John Tyssowski

IN 1925, Harry Howard Stout, then metallurgist for Phelps Dodge Corporation, while investigating the cleaning of cathode copper by various gases at elevated temper-atures below the melting point of the metal, observed in the laboratory that particles of pure copper heated in a closed tube filled with hydrogen seemingly "stuck together." By further investigation he found that there was actual crystal growth across the boundaries of the particles of pure metal; in other words, there was a complete new crystal realignment and growth throughout the newly formed copper mass. It was coalescence, not adhesion; the several parti-cles had become one unit. From this dis-covery has been developed the coalescence process, whereby copper of cathode purity is squirted out in semifabricated form from an extrusion press, by the appli-cation of about 30c0 tons pressure on a 10-in. piston. Stout decided that cathode copper pro-duced by electrolytic deposition was the logical source of the pure copper required for the coalescence process, but as there was no way of reducing the ordinary tough commercial cathodes to the small particles required he was confronted by a serious problem at the outset. Under his direction, this problem was solved by William H, Osborn and Harry Howard Stout, Jr. They developed the process and technique for producing cathode copper in brittle, friable form, and to them must be given the greater part of the credit for this phase of the development program as well as for that relating to the gas cleaning of the cathode particles.

Jan 1, 1940

By C. E. Mendenhall

FOR the purpose in hand, pyrometry may be taken to include all temperature measurements from, say, 200° C. to the highest attainable, especially when considered from the technical or applied side. It will be convenient first to consider the entire content of a course of study grouped under the headings of the various methods of measurement, which are quite distinct in principle and involve different equipment. Brief suggestions will be given under each heading, and the summary will be followed by comments on the purpose of such a course and methods of conducting it. 1. Expansion and pressure methods: mercury thermometers (glass and quartz), liquid, gas, and vapor-pressure thermometers, especially recording instruments. Especial attention should be given to the limitations of these methods, which, particularly in high-temperature mercury thermometry, are often overlooked. Range approximately to 700° C. 2. Resistance thermometers: both bridge and potentiometer methods, of indicating and recording. Calibration; lead compensation; design of thermometers for special purposes. Range to 1200° C. 3. Thermoelectric pyrometers: potentiometer and deflection methods indicating and recording. Calibration, leakage errors, contamination errors, base and noble couples. Range to 1500° C. 4. Total radiation methods: thermoelectric, resistance, and expansion indicators, mirror and lens collectors, calibration, permanence of characteristics, absorption errors. Range, to highest attainable temperatures. Methods of producing perfect radiators-true, and virtual or "black body" temperatures. 5. Partial radiation methods: absorption and spectroscopic methods of getting partial radiation, various comparison sources, polarization, electric, sector, and absorption methods of controlling intensity (Morse, Lummer, and Wanner types). Calibration, permanence of calibration, absorption errors. Methods of producing perfect radiators -improvised methods; true, and virtual or black-body temperatures.

Jan 9, 1919

By T. F. Witherbee

AS the forms of blown-out furnaces are of much interest to ironmasters and metallurgists, the manner of taking the accompanying sections of the Cedar Point stack is here given. The diagrams show the original and also the final shape of the furnace after a two years and twelve days' blast,, during which the following solid materials passed through it, viz.: Coal, 41,000 tons; ore, 57,000 tons; limestone, 30,000; total, 125,000 gross tons. Product, 411/4 tons per day Bessemer pig iron. The apparatus used in taking the sections was a modification of that proposed by Mr. Frank Firmstone,* and consisted of a sliding rule, to follow around the circumference of the stack, which rule was connected by a string to a segment of a circle of 24 inches radius. The segment was carried by an arm which connected it to a huh as a centre, 2 inches in diameter. A second string was wound around the hub, and communicated motion to a pencil-carrier, the pencil of which marked out on paper the exact outline, and reduced it to a scale of & inch to the foot. The whole machine was made in about three hours, with the facilities of a carpenter's shop, and gave in operation every irregularity of the lining. The sections were taken at salient points, by lowering a hanging staging on which the apparatus was placed. Tracings from the paper of the machine were made, and, as in this case several copies were required, the tracings were glued on to thin sheets of basswood, and patterns carefully sawed out with a bracket saw.

Jan 1, 1879

By H. L. Riley, B. W. Gandrud

As far as the present writers know, this system of flotation has not been used elsewhere in this country, but in the last couple of years it has been introduced, with minor variations, at one plant in England and one in Wales. The system has been described and discussed in a number of publications. The following is quoted from an abstract of the latest of these," a paper presented at an International Conference on Industrial Combustion in 1952. On the basis of experience to date with the commercial plants, it is believed that the kerosene-flotation process incorporates all the necessary elements to make it greatly superior to anything else now available for treating of fines in wet processes of coal preparation. Additional study and investigation are still needed, however, to determine if certain phases of the process can be improved to such an extent as to make it generally satisfactory and acceptable to the industry. Further improvements will be needed with respect to the capacities of the flotation cells and the reagent consumption.

Nov 1, 1955

Owing to circumstances which are entirely unavoidable, the cost of rendering to Institute Members the services which they have been ac-customed to expect from the Institute has increased enormously, especi-ally during the past year. The cost of printing has increased 20 per cent. and another 30 per cent. is expected. There is no recourse; the Institute must pay this or cease publishing. The increase for supplies and office force will be very great. Justice to our employees, whose cost for living expenses has risen by leaps and bounds, demands an increase in. wages, wholly aside from the fact that the employees need not and will not stay. The Institute is, therefore, faced with the alternative of greatly re-ducing its service to the members or else of asking from them a small increase in clues. An amendment to the Constitution has been offered by the members increasing the clues to $15 per year, which cannot become effective until 1921. This still leaves us as the engineering society with the lowest annual clues, except only one, whose dues are $15 per year. To help meet the immediate emergency, the Directors have exercised the authority vested in them by the Constitution and By-Laws and requested the members to pay $3.00 for the Transactions to be issued during the year 1920, which is very much less than the cost of publication. It is the opinion of the Board that the members will prefer to pay this slightly additional expense rather than to have the Institute take a backward step in respect to the services which it is rendering, and which has been increasing constantly in amount, as well as in unit cost, during the past seven or eight years.

Jan 12, 1919

By John R. Weeks, Dan McLachlan, John R. Lewis

DURING the operation of the iron blast furnace, aggregates of hard, infusible, yellow, cubic crystals frequently form in the interstices of the lining and on the hearth of the furnace. These were first examined by Wohler&apos; and were identified by him as a complex cyanonitride of titanium, having a formula Ti(CN)2 • 3Ti3N2, or more simply Ti10C2N8. However, recent investigators have suggested that this complex compound does not exist. Recent work by Hume-Rothery, Raynor, and Little2 on the carbide and nitride particles in titanium steels suggests that a complete series of solid solutions of the general type Ti<0+y>C0Ny exists between titanium carbide (Tic) and titanium nitride (TiN). Assuming this to be true, it seems likely that Wohler&apos;s cyanonitride of titanium is in reality a solid solution of 20 mol pct Tic in 80 mol pct TiN, .the nearly consistent carbide-to-nitride ratio probably resulting from temperature and pressure conditions in the blast furnace. The object of the present work was to investigate thoroughly this possibility of a solid solution by using the single-crystal methods of X-ray analysis. A spectrographic qualitative analysis of a sample of the yellow crystals furnished by the Geneva Steel Co. sh&apos;owed, in addition to the titanium, strong lines of vanadium and moderate to weak lines of iron, magnesium, silicon, aluminum, and calcium. The last five were probably slag impurities, but the vanadium was possibly included in the yellow crystals, owing to a great structural similarity of its carbide (VC) and its nitride (VN) to the titanium compounds, Table 11. A chemical analysis was made

Jan 1, 1952

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their tine in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will -be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 5, 1915

By L. L. Hirsch, W. M. Parris, P. D. Frost

IT has been established that titanium alloys con- taining sufficient amounts of ß-stabilizing elements, such as iron, chromium, or manganese, can be age hardened.&apos; Adenstedt, Pequignot, and Raymer2 showed that age hardening occurred in a Ti-15 pct V alloy at room temperature after it was quenched from a temperature in the ß-phase region. During a recent investigation of the heat-treating characteristics of binary Ti-Mn and Ti-Cr alloys at Battelle, further evidence of low temperature aging was found. Appreciable hardening occurred in some of these alloys at aging temperatures as low as 212 OF (100oC). Indeed, the brief heating period employed for mounting metallographic specimens in bakelite resulted in hardening. It was felt that further information on this low temperature aging phenomenon would be of general interest in view of the large amount of work currently being done on titanium alloys. The alloys examined in this investigation were arc-melted in a water-cooled copper crucible as 3/4-lb ingots. Du Pont Process A sponge was used as a base material. The arc-melted ingots were forged at 1700" to 1800°F (927" to 982°C) and hot rolled at 1450°F (788°C) to 14 gage (0.064 in.) sheet. Small specimens were heated in argon at 1742°F (950°C) for 30 min and quenched in various liquid media or air cooled. They were then mounted in a room-temperature-setting resin and given a metallographic

Jan 1, 1954

By J. H. Brophy, A. I. Prill

The authors have previously investigated the solid-state activated sintering of tungsten powder with various Ni-Cu additions.&apos; Log shrinkage vs log time plots showed changes in slope from 4 to x at intermediate times during the sintering process. This was attributed to a change in the rate-controlling mass-transport process from solution of tungsten into the tungsten-alloy interface to diffusion of tungsten in this interface. It was postulated that the melting of the activating layer should not affect this transport process. However, the superposition of rearrangement due to the presence of a liquid phase complicates the data analysis. It is the purpose of this note to apply the analysis of Prill, Hayden, and rohy&apos; to account for "rearrangement shrinkage&apos;? in liquid-phase sintering of the W-Ni-Cu system. This results in "solution-precipitation stage" shrinkage plots which were comparable to those obtained in solid-phase activated sintering of the same system. If one assumes total shrinkage to be the sum of rearrangement and solution precipitation, the effects can be isolated easily.2 This results in the general equation:

Jan 1, 1967

By E. Alan Haley

Accurate and economic control of line and grade on long tunnels, large structures, excavations and waterways has been a problem to surveyors and engineers for decades. The conventional method of surveying, incorporating a level, transit and a number of surveying technicians, has proven to be a very expensive and time-consuming operation. Now, however, engineers have adapted the laser to help ease the problems of surveying, at the same time increasing the efficiency of such operations. The laser, which projects a continuous, narrow red beam of brilliant light, provides a constant alignment reference that does not interfere with personnel or equipment. A complete laser alignment system, specifically designed for and suited to a variety of mining and tunneling operations, has been developed by the Perkin-Elmer Corp. The engineering significance of this development can be fully realized when it is noted that, aside from potentially tremendous economic advantages in terms of labor savings, the laser beam provides a system of alignment that is at least ten times more accurate than presently used optical systems. The new laser system provides accuracies within 10 microinches per foot (1 x 10-5in.) when used with an accessory centering detector. In one of its first field trials, the laser was used for alignment of a two-mile tunnel which showed a total deviation of less than 5/8 in.

Jan 4, 1968

By C. Jackson, J. J. Harrington

The pH control system at Kennecott Copper Corporation&apos;s Nevada Mines Division concentrator consists of two independent systems, lime dilution and lime addition. Lime dilution is accomplished in a mixing tank where slaked lime and water are introduced proportionately. The desired dilution of the milk of lime is determined by the electrical inputs provided by eight pH probes, one per grinding section. The inputs are averaged and applied to a time base generator. The summation output of the time base generator determines the proportion of lime and water that are to be mixed and applies this input to a voltage sensitive switching device. The switching device provides a signal to one of two relays which will add either slaked lime or water, dependent upon the summation output. The entire cycle is based on a 2-min repetition rate to allow for sufficient mix time. Responsivity is controlled by maintaing a limited maximum solution level in the mix tank. Lime addition is controlled independently within each grinding section. The electrical input from the pH probe in a given section controls the solenoid valves which provide lime to each of the ball mills. The valves remain open within a time range capable of maintaining the pH of flotation feed at a given set point.

Jan 1, 1978