Search Documents

By Clarence Seyler

THE technical difficulties of cutting thin sections of coal for examination by transmitted light have hitherto restricted the investigation of the important subject of the microstructure of coal to the few possessed of the requisite skill and time. Apart from this, the method fails with anthracites and other coals rich in carbon, owing to the opacity of the material. Occasional use of the method of polishing a surface, with or without etching, has been made, but it was not until Winter1 published an account of his results that attention was seriously directed to the method. In May, 1923, a specimen of dull anthracite came into my hands; I tried Winter's method on it and the presence of megaspores and other vegetable structures became clearly visible. A preliminary notice was published by me;2 but I soon abandoned the use of Schulze's solution having found that a mixture of chromic and sulfuric acids gave far better results. In the meantime Turner and Randall, in America, had independently developed the method of flame etching, as applied to anthracite, with great success. I have spent a year studying the method of chromic etching, which gives excellent results with bituminous coals and cannels, as well as with anthracite. For anthracites, I have used the chromic method and Turner's method of flame etching, whichever was the more convenient or as a check one on the other. The polishing is done, according to metallurgical practice, by the use of a polishing machine and successively finer emery paper, followed by polishing on cloth moistened with a suspension of levigated green oxide of chromium, and a final rubbing on "selvyt" (a cotton velvet polishing cloth) moistened' with alcohol. The polished sample is examined by reflected light with a 2/3 and 1/6 in. objective. Bituminous coals usually show considerable structure, and even anthracites show it faintly in places. The sample is then etched by immersion in a boiling solution made by adding 10 c.c. of concentrated sulfuric acid to 30 c.c of a saturated solution of chromic acid; enough water is then added to dissolve

Jan 3, 1925

By AIME AIME

APPARENTLY unperturbed by any misgiving as to ill luck connected with the mystic number thirteen -for there were exactly that number of Directors on deck-the Board held two sessions on Tuesday, Feb. 21. , . Between the executive session at 5:15 p. m. and the general session at 8:30 p. m., 28 Section and Division delegates were wests of the Directors at dinner. Committee chair- " men and past officers brought the attendance to 75. Messrs. McAuliffe, Merica, Mudd and Tally had expressed their intention to be at the Directors' meeting, but each was prevented unavoidably at the last minute. At the executive session of the Board, J. V. W. Reynders was unanimously chosen to fill the unexpired term of Dr. Becket as Director: and Eugene McAuliffe in like " manner was selected to become Vice-president to fill the vacancy created hy Dr. Becket's assumption of the Presidency. Upon nomination of President Becket the following Executive Committee was appointed: Frederick M. Becket, chairman; Howard N. Eavenson, H. A. Guess, J. V. W. Reynders and William Wraith; and the Finance Committee was appointed as follows: Henry Krumb, chairman; Paul D. Merica and H. G. Moulton. Karl Eilers was reelected Treasurer and A. B. Parsons was re- elected Secretary to serve for the ensuing year, whereupon the executive session was adjourned.

Jan 1, 1933

By R. A. Matuszak

This paper discusses the major portion of the hoist (drag or crowd) system and it shows how static control accomplishes its major aims. In 1959, the first truly static control for Ward-Leonard equipped electric excavators was designed, developed and placed in service. The control system, originally intended only as a more modern electronic type of alternate to the proven rotating amplifier control system has since proven to be much more. When they conceived the original system, the designers had much more in mind than simply replacing the rotating amplifier with one that had no moving parts. The long range plan, which started with the initial system consisting of an SCR (silicon controlled rectifier) preamplifier and magnetic amplifier power amplifier, called for eventually, a control system low in cost and maintenance, relatively simple in design and extremely reliable. The plan also included the elimination of as many of the shortcomings of the rotating system as possible. No small accomplishment, when it is considered that the rotating control system had been, with only minor modifications, the standard of the industry for 20 years. The final step in the original design plan called for the eventual development of an amplifier that could be used as one of the basic building blocks of the future. DEVELOPMENT RESULTS Since the successful unveiling of the first static control system, continuous development has resulted in a slow, but sure progression along the path described by the original plan. The first version of the new control corrected one of the shortcomings of the rotating system by removing the necessity of operator anticipation. This was accomplished by making the system faster in response so that the operator noticed virtually no delay between his movement of the master controller and that of the machine. Thus, after the operator became familiar with the operating characteristics of the machine, he was able to become more relaxed while digging. The natural result of this accomplishment was higher production. All of the subsequent versions of this new control were even faster than the initial design. Although it was not distinguishable by the operator, the further increase in response resulted in large gains in the limiting of transient torque peaks applied to the machine while digging. Also, a more effective control of the torque and power peaks was obtained when plugging the motion being controlled to a stop. (Plugging is the use of the Ward-Leonard ability to regenerate power and absorb energy from the load to

Jan 1, 1964

By C. Stansfield Hitchen

THE introduction of the logarithmic sector method of quantitative spectrography by Scheibe and Neuhäusser in 1928, and the subsequent .modification and improvement of the method by Twyman and Simeon, would seem to have marked yet a further advance in quantitative spec-trum analysis and its industrial application, inasmuch as it offers a simple means of eliminating some of the uncertainties inherent in the older methods based upon mere visual comparison of line intensities. In their recent admirable review of the position and capabilities of industrial spectroscopy, Brownsdon and van Someren1 say: Ways and means of facilitating the comparison of line-intensities so as to give them numerical values are helpful, and of these a logarithmic sector rotating in front of the slit appears to he one of the most promising; . . . the success recently experienced by the author in using this method for the examination of steels and solutions of metallic salts prompted him ,to investigate its possible use in estimating the impurities commonly present in crude and refined tin. The results of this investigation are submitted in the present paper. Details of a number of spectrographic analyses of tin for various impurities have already been published. Thus, Schweitzer2 describes the spectrographic examination of tin for lead, bismuth and cadmium, and was able to distinguish between such atomic percentages as 0.01, 0.05, 0.10, 0.30, 0.60, 1.20, 3.00 and 10.00. Negresco3 investigated the bismuth content of tin over a range of from 0.0005 to 35 per cent. Meggers, Kiess and Stimson4 compare spectrographic and chemical analyses of tin metal for copper, lead, iron, zinc, silver, nickel and bismuth. They stress also the value of spectrum analysis in the examination of tin used for boiler plugs, where the requirements that only minute quantities of impurities shall be present render the chemical analysis both tedious and difficult.

Jan 1, 1933

By M. S. Klima, P. T. Luckie

Interfacing new or improved unit operations SUBMODULES with the EXECUTIVE of a macro analysis simulator usually requires modification of the input data. For example, particle processing SUBMODULES that are sufficiently general in nature to provide useful predictions require input data for rather narrow size fractions. Such data is not always available for the EXECUTIVE and must therefore be generated by the SUBMODULE. A successful interface to allow incorporation of a new SUBMODULE for comminution and one for classification in a general stream state flowsheet simulator is presented. The general nature of the SUBMODULES, as well as the logic of expanding and contracting the required data input is discussed.

Jan 1, 1983

By E. S. Bumps, W. F. Craig, M. Baeyertz

Metallurgists have looked at fractures macroscopically for many years and have evolved a vocabulary in which such words as "cleavage," "brittle," "shear," "ductile," "granular," "fibrous," and "silky" are used to describe the appearance of the fractured surface; but the meaning of these words in terms of metal structure is not well established. Observations of the structural meaning of "brittle" and "ductile" fractures in plate steels have been made, notably, by Kramer and coworkers1 and by Tipper.2 Grossman3 has studied the fracture of tempered martensite and combinations of ferrite and martensite. Notwithstanding these and other less concerted attacks on the problem, present understanding of fracture rests more on assumptions and logic than on experiment. It is the purpose of this paper to add a little to the growing fund of experimental observations of the nature of fractures in steel. The particular fractures to be described were obtained in conventional impact testing of an ordinary structural steel shape. In impact tests of the Charpy type, the specimens fail in a characteristic manner that depends on the steel and the temperature of testing. With ordinary structural and many other steel products, an appropriate range of testing temperature will cause a considerable change in the energy absorbed before fracture. This change is known as the energy transition and is accompanied, more or less closely, by alteration in the appearance of the fracture. At testing temperatures below the transition, the terms "brittle," "cleavage," or "granular" are used to describe the fracture; above it, "ductile" or "shear" are often used. Within the transition, the fracture changes from "brittle" to "ductile" by a progression in appearance, wherein the "brittle" portion of the fracture becomes restricted to a smaller and smaller central area of the fracture, as the testing temperature is raised and the "ductile" type of fracture is approached. All this is well known to metallurgists. The specimens under consideration are of the conventional V-notch Charpy type. They were taken from a structural steel shape of the following analysis: C Mn P S Si 0.17 0.46 0.009 0.029 0.03 Both longitudinal and transverse specimens were tested and examined. Fig 1 shows the energy values plotted against testing temperatures in the usual way. The curves for both longitudinal and transverse specimens show an energy transition, although the maximum energy absorbed at testing temperatures above the transition is greater in the case of the longitudinal specimens. Fig 2 illustrates the changes in the macroscopic appearance of the fractures that are associated with the energy transitions shown in Fig 1. Macrographs of the fractured surfaces of the specimens have been identified with the fracture ratings at intervals on each fracture curve. The numerical fracture rating on the ordinate of Fig 2 indicates the percentage of the area of each fracture that was considered to be "brittle" on macroscopic observation. Such rating of the fracture type in impact tests is now customary in many laboratories. Hereafter the specimens will be identified by reference to Fig 2 as 90 pct "brittle," 80 pct "brittle," and so on, in accordance with this macroscopic evaluation of the appearance of the fractured surface. The discussion of the fractures is divided into three parts. The first two are concerned with the mode of fracture and its relation to general structural features. As the same metal-lographic features occur in both longi-

Jan 1, 1950

By M. J. Salkind

In order for fiber composite materials to find extensive use in structures, it is necessary to develop techniques for joining these materials. Riveting and adhesive bonding are two possible techniques which have been investigated although the former is less desirable because the low shear strength of most matrices makes this type of joint subject to bearing failure. Welding is an effective means of joining, especially for high-temperature applications where ad-hesives are weak; however, there are significant limitations placed on welding composite materials. The commonly used fusion welding techniques will find less use for joining composites because the two phases are often unable to stand exposure to such a stringent environment. In the case of eutectic composites, fusion welding will completely destroy the controlled microstructure. Solid-state techniques such as diffusion bonding offer potential success with certain design requirements placed on such joints. Since the primary mechanism of load transfer from matrix to fiber is shear parallel to the fibers, little load can be transferred across a butt-welded interface perpendicular to the aligned fibers. Successful joint designs must have a component parallel to the fibers to allow a shear area for load transfer. Configurations such as lap and scarf welds are likely to be successful. This note describes some results of experiments with diffusion-bonded joints in A13Ni whisker-reinforced aluminum. The composite material, prepared by unidirectional solidification of the A1-A13Ni eutectic, is described elsewhere.'-' It consists of aligned micron size whiskers in a matrix of aluminum. Since it has been shown that the microstructure of

Jan 1, 1969

By G. W. Jones

THIS paper describes experiments in which eight test samples of gelatin dynamite were fired in three different types of apparatus and the quantity and composition of the gaseous products of detonation determined. The special dynamites were so prepared that the oxygen balance of the samples varied from -35.0 to +6.0 g. per 100 g. of explosive, including the wrapper. By means of this graded series of explosives, the relation between oxygen balance and gaseous products of detonation could be studied explicitly. The effect of varying oxygen balance on explosive strength has been discussed in another paper.1 The apparatus employed in the work described in the present paper included (1) the Bichel gage, a steel bomb of 15-1. volume; (2) the Crawshaw-Jones confined detonation apparatus, a steel cannon from which the explosive is fired into a pipe of 90-1. volume; and (3) the Hercules tank, an apparatus in which the explosive is confined in a quartz block which is placed in a steel tank of about 4500-1. volume. A full description of the apparatus is given later. VARIABLES AFFECTING COMPOSITION OF DETONATION PRODUCTS The character of the detonation products of commercial explosives is governed in part by the same factors that affect the combustion products from explosive mixtures of air with gases or vapors. In either case, combustible materials-namely, carbon, hydrogen, and sometimes sulfur-are present and combined variously. In an exploding gas mixture the combustibles are oxidized by oxygen in the admixed air, whereas with explosives the necessary oxygen is provided by oxygen-carrying materials in the explosive ingredients.

Jan 1, 1928

Jan 1, 1941

Jan 1, 1941

By B. S. Norris, Charles R. Austin

The stresses which initiate deformation processes in metals are fundamentally important in the study of the mechanical properties of metals. A point of inflection in the load-elongation curves obtained for single crystals' has been rather too readily interpreted as a true yield point, and the critical resolved shearing stress on the plane of slip taken as a material constant. Even early work showed that the stress at this point varies with rate of loading, but it has not been generally appreciated that creep tests under static loads alone are suited for determining the existence or nonexistence of a yield point.* It has now been shown by Miller that single crystals of zinc3 when loaded statically begin to yield at loads too small to measure; as a result there is no case now known, apart from that cited in the present paper, in which a true critical stress for yielding has been demonstrated for single crystals of metals. The case of iron has especial interest: the existence of an upper and lower yield point and of an elongation at the yield point in ordinary iron and steel marks this substance as unusual, though the effects have been found to a very minor degree in other metals and alloys. $ Most alloys do not show such marked phenomena when appreciable yielding begins, and accordingly modern practice is to speak of the yield strength of such materials, a stress read from the load-elongation curve after elongation has begun, rather than yield point. The special behavior of iron suggests that it is more likely that single crystals of iron should have a true yield point than other metals. The study of the mechanical properties of metals and alloys requires a determination of the crystallographic mechanism of deformation, wlletller deformation proceeds by slip, twinning, or cleavage, or a combination of these, and a determination of the stresses that induce these modes of deformation. With this information, a study of the rates of work-

Jan 1, 1938

By B. S. Norris, Charles R. Austin

The stresses which initiate deformation processes in metals are fundamentally important in the study of the mechanical properties of metals. A point of inflection in the load-elongation curves obtained for single crystals' has been rather too readily interpreted as a true yield point, and the critical resolved shearing stress on the plane of slip taken as a material constant. Even early work showed that the stress at this point varies with rate of loading, but it has not been generally appreciated that creep tests under static loads alone are suited for determining the existence or nonexistence of a yield point.* It has now been shown by Miller that single crystals of zinc3 when loaded statically begin to yield at loads too small to measure; as a result there is no case now known, apart from that cited in the present paper, in which a true critical stress for yielding has been demonstrated for single crystals of metals. The case of iron has especial interest: the existence of an upper and lower yield point and of an elongation at the yield point in ordinary iron and steel marks this substance as unusual, though the effects have been found to a very minor degree in other metals and alloys. $ Most alloys do not show such marked phenomena when appreciable yielding begins, and accordingly modern practice is to speak of the yield strength of such materials, a stress read from the load-elongation curve after elongation has begun, rather than yield point. The special behavior of iron suggests that it is more likely that single crystals of iron should have a true yield point than other metals. The study of the mechanical properties of metals and alloys requires a determination of the crystallographic mechanism of deformation, wlletller deformation proceeds by slip, twinning, or cleavage, or a combination of these, and a determination of the stresses that induce these modes of deformation. With this information, a study of the rates of work-

Jan 1, 1938

By William Phillips

THE earliest mention of the sulphur deposits in what is now Culberson County, Texas, seems to be contained in "Explorations and Surveys for a Railroad Route from the Mississippi River to the Pacific Ocean, United States War Department, 1853-54." Captain John Pope (he was not commissioned Captain until 1856) had charge of one of the divisions of the Survey. In his report on the geology of the route, William P. Blake noted the analysis of a greenish earthy powder from the bed of Delaware Creek, at the springs, which contained 18.28 per cent. of free sulphur. The report states: "From the chemical examination of the waters of the spring, by Dr. Booth, it appears that chloride of sodium is the principal solid ingredient, but considerable quantities of sulphide of sodium are present. * * * * * The waters from the springs examined by Dr. Booth were alkaline, but it is possible that some of the springs are acid; and in this case the precipitation of sulphur would ensue on the mixture of the acid waters with those charged with alkaline sulphurets and the origin of the deposits of sulphur would he thus explained." This is the first reference to the existence of sulphur in that region, the first mention of the character of the water found there and the first suggestion as to the' origin of the deposits. The possibility of the existence of acid waters was confirmed by E. M. Skeats, nearly 50 years later.1 In this publication, Skeats says that the water from the sulphur deposits in Section 11, Block 114,, Township 5, contains 79.08 grains of free sulphuric acid per gallon. This locality is about 13 miles (21 km.) south of Delaware Creek and about 35-miles (56 km.) east of the Delaware Springs. The next published reference to the existence of sulphur in Trans-Pecos Texas is in the First. Annual Report of the Geological Survey of Texas, 1889, page 226, where W. H. von Streeruwitz mentions that sulphur is found in that region, but gives no further information. In the

Jan 9, 1917

By Charles W. Frey

OF all the machinery used in mining work, mine cars are probably the most abused. They are hauled through water and muck, up hill and down grade, whipped around curves, bumped and jerked, and exposed to the ravages of the weather. However, as a general rule their lubrication is not altogether neglected. The mine operator may not heed the extra drag that a frozen conveyor bearing gives, but he is all too aware of the increased load that faulty mine car wheels put on his power plant. When the circuit breakers begin to fly, and when his mine loco- motives come out with only half the cars that they were able to carry a month before, then neglected mine car wheel lubrication becomes apparent, and woe to the person responsible.

Jan 1, 1938

DEFENSE Materials Procurement Agency has been moving rapidly to encourage copper industry expansion programs. Although copper production is at a high level, a shortage exists on a world-wide basis as well as on the domestic scene. Projected expansion programs will not ease this current demand for most of them are 2 to 5 years off. Refining facilities are adequate but there is a shortage of ore and scrap, and it is for this reason that the expansion programs are directed at developing more sources of supply. The domestic expansion programmed thus far and understood to have been arranged with price escalation should the domestic price go to 271/20, were summarized by American Metal Markets as follows (dates of announcement are given in parenthesis: .1-Copper Cities Mining Co.'s, $15,000,000 expansion near Miami, Ariz., to be operating about 1954. DMPA will buy 22,500 tons of copper a year up to a given amount on an agreed price of 23¢ per pound, with some exceptions and depending upon salability at a higher price to other purchasers in the U. S. (September 25th). 2-An RFC loan of $60,000 to North Butte Mining Co. to be paid off on the basis of deliveries at a purchase price of 241/20 per pound (September 25th). 3-A $25,000,000 expansion program by Phelps Dodge to provide 38,000 tons per year by late 1954. DMPA would purchase it at a price of 22¢ per pound up to 112,500 tons providing other purchasers in the U. S. will not pay a higher price (September 26th). 4-Anaconda Copper Mining Co. $40,000,000 expansion in Nevada to provide more than 30,000 (might be increased to 45,000) tons per year. DMPA would purchase the copper at 250 per pound for a limited period of time if it is not salable to industrial users at above this price. Production would start around 1953 (November 14th).

Jan 1, 1952

By A. L. Galpin

INTRODUCTION For many tailings ponds, particularly those having substantial watershed areas, the control of pond water levels will be a major factor influencing the operation of the pond and the design and construction of the dam retaining the pond. This paper summarizes the basic factors affecting the control of water in tailings ponds, methods of water control, and methods of estimating the variables involved. The influences that pond water levels can have on the design, construction, and stability of tailings dams are explained in order to emphasize the importance of water control in the overall planning of mine tailings disposal systems. Two examples of pond water control planning conclude the paper. BASIC FACTORS The principal factors influencing the control of water in tailings ponds are illustrated on Fig. 1. Fig. 1 (a) shows the general disposition of the tailings solids and water in the pond; the solids settle from the slurry to form "slimes", deposits sloping down into the pond from the points of discharge; these slimes hold volumes of water in the voids between solid particles; water in excess of this "retained" water forms a pool of "free" water laying over the slimes deposits. In some cases, tailings solids (and water) go to the tailings dam for its construction. Fig. 1 (b) indicates those ways additional to tailings disposal in which the pond gains or loses water. These include surface and sub-surface runoff from the pond watershed, water reclaimed from the pond for ore processing, evaporation, and seepage. Seepage losses sometimes include water draining from tailings sand placed in the dam, but a portion of the total seepage flow is often collected and returned to the pond in order to avoid downstream pollution and to recover water for re-use. PRINCIPAL REQUIREMENTS In relation to the control of water in a tailings pond, the first requirement is usually to maintain a pool sufficiently large to ensure adequate clarification of the free water prior to its reclaim for use in the mill, or its discharge from the pond.

Jan 1, 1972

J. B. MCGRAW, New York, N. Y. (written discussion*).-In Mr. Burke Baker's description of the process of the American Briquet Co., he speaks only of the attractive features, but every process which uses a compound or emulsified binder has certain undesirable features which must be considered. In making an emulsion, the success of which depends upon the introduction of the various ingredients at certain fixed temperatures and the complete intermixing of a soluble solution with an oil which has absolutely no affinity for it, considerable difficulty is found in keeping the various factors in strict accordance with the formula. To serve its purpose properly or, in other words, to be right for easy mixing with the coal, it should be of a certain predetermined density. Among the controlling factors of this ate the proportion of moisture contained and the temperature of the oil when introduced. If the latter is higher than intended, a greater proportion of moisture will be evaporated than is proper, and if the oil is not sufficiently hot the process of emulsification is retarded. These various factors can be controlled with more or less certainty where working in a laboratory or in a small experimental way, but when it is attempted on a large commercial scale, certain obstacles not otherwise apparent are likely to be encountered.

Jan 5, 1918

By H. E. Lee, P. C. Feddersen, D. R. Gittinger, G. W. Dunn, J. B. Schuettenhelm

The new Bunker Hill slag-treatment plant, designed ior, a capacity of 300 to 400 tons of hot slag per day, was "blown in" April 5, 1943. In the ensuing I5-months period, 157,530 tons of slag was processed, with an average recovery of over go per cent of the zinc and practically all of the lead contained. In addition to this high metal recovery, utilization of the waste heat in the gas and fume venting, the process has enabled the generation of 231,376 tons of steam at 250-lb, gauge. Over the first six months opcration the volume of slag treated averaged somewhat under 300 tons per day. Reclaimed dump slag made up only about 1 5 per cent of the plant feed. In October 1943, preparations for the smelting of additional tonnages of dump slag were completed and the plant capacity was increased to an average of about 420 tons of slag per day. During the nine-months interval since that date, monthly averages of 450 toils per operating day have been maintained several times. The new plant (Fig. I) is constructed in close proximity to blast-furnace operations. The fuming furnace and other necessary equipment are housed in an eastward extension of the existing blast-furnace building. Beyond this housed extension the dust-laden gas is conveyed about the perimeter of a large rectangle formed by the flues, cooling towers and baghouses. The course of a 10-ft. balloon flue, which transports the fuming furnace gas, describes the west and south perimeters. This flue connects with a set of cooling towers located at the southeast comer. The flue and cooling-tower system serving the deleading kiln constitute the north side and the two baghouses, serving the kiln and furnace operations, -border the east side. From these baghouses the several discharge gas flows are come biped and conveyed in to the rectangle, being vented to atmosphere by means of a fan through a centrally located zoo-ft. brick stack. In general, the plant design and operation follow quite closely that dictated by experience gained in years of slag-fuming practice by the Anaconda Copper Mining Go., at East Helena, Mont., and the Consolidated Mining and Smelting Co. of Canada, Ltd., at Trail, B.C., and more recently by the International Smelting and Refining Co. at Toocle, Utah. : Fuming operations at the East Helena and the Tooele plants are more or less identical. Trail practice differs chiefly in the methods employed for the storage of the hot feed slag and in the methods utilized for the handling and cooling of the fuming furnace gas. The new Bunker Hill fuming plant closely follows Trail procedure in the treatment of the furnace discharge gas while East Hclcna methods have been adopted for the storage of feed slag.

Jan 1, 1944

By C. L. HUNTZINGER

THE mine here described is in the Witbank district, a coal area of the Transvaal, about 100 miles north- east of Johannesburg. and is owned by the Witbank Colliery, Ltd. The plant has a capacity of 4000 tons per eight hours, and prepares five sizes of coal. The coal seam lies at a depth of about 200 ft. below the surface, and is reached by an inclined shaft sunk at an angle of 18° with the horizontal. Although the thickness of the coal seam varies from 10 to 14 ft. or more, only about a 7-ft. bench is mined. Mining is by the hord and pillar system. Bords are driven 18 ft. wide, with pillars measuring 18 ft. square. The mine is laid out into four sections, each sewed by a main haulage way from the shaft. Arc-wall machines are used for cutting the coal. but all loading is done by hand. Native labor is employed under the supervision of white miners, who do the required blasting. The workings are practically free from gas and water, and very little timber is needed.

Jan 1, 1931

By D. A. J. Swinkels

The problem of determining oxygen levels in liquid steel to aid in deoxidation control has received general attention for a number of years. Work in this direction started at the B.H.P. Central Research Laboratories early in 1967 with an evaluation of sampling techniques followed by vacuum fusion analysis to determine the oxygen content of the samples (1). It was found that these techniques had a number of drawbacks if they were to be used for deoxidation control. The method of analysis was rather too slow to allow effective control and measured total oxygen level rather than dissolved oxygen. Furthermore, the results were found to be very variable due to slag entrainment in the samples. Attention therefore turned to the galvanic cell method using a solid oxygen ion conductive electrolyte such as cubic stabilised zirconia. The ionic conductivity properties of electrolytes such as (ZrO2) 85 (CaO).15 had been studied by a number of investigators and had already been applied to the measurement of oxygen activity in gases, in lower melting metals such as copper, lead, tin, silver, alkali metals and indeed the first studies in steel had been made (2,3). Since then the results of a number of studies in the development of an expendable oxygen probe for steel have been reported (4-9).

Jan 1, 1972