Search Documents

By Franklin R. Carpenter, W. P. Headden

TWO notes have already appeared in the Transactions concerning the columbite or tantalite of the Black Hills tin-mines. In vol. xiii., page 232, Prof. Schaeffer speaks of the mineral as tantalite, and concludes by saying that its separation from the tinstone "is a matter which will, I believe, prove puzzling to the wisest metallurgist." He also observes that he is unable to find by analysis in his specimens the least trace of columbic acid. Prof. W. P. Blake, in the same volume, at page 696, says: " Even if it [tantalite or columbite] were present to a considerable amount, it would not injure the tin in smelting. It does not alloy with tin, but carries a small percentage of tin, which would probably be liberated in smelting." He calls the mineral columbite from the fact that a great number of specificgravity tests invariably indicated that it should be so classed. We have made chemical tests as well as specific-gravity tests upon many samples from many different parts of the Hills. Our analyses have always shown the presence of columbic acid, and the specificgravity tests have always indicated columbite, as we have elsewhere shown.* As Prof. Blake has already observed, it is not found in such close association with the tin as to prevent separation by a rough handsorting, but it is usually present with the stream-tin. As Prof. Schaeffer says, it cannot be separated by ordinary concentration; and while, as declared by Prof. Blake, its columbic acid may not unite with the tin in any form, yet its iron and manganese oxides may be reduced, and thus lower the quality of the tin produced, as is also the case when the smelting charge contains wolfram. To determine the effect of columbite in the ordinary potassium cyanide assay, there were assayed at the Dakota School of Mines four samples containing different proportions of columbite. The results, published in the report of the school for 1888, seemed to indi-

Jan 1, 1889

By Walter O. Snelling

Continuation of the discussion of the paper of WaltER o. SnelLIng, presented at the New York and San Francisco meetings, February and September, 1915, respectively, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704 and Trans., li, pp. 657 to 671. A. C. McLaUghlin, San Francisco, Ca1.—It seems to me that Mr. Snelling's work, if it is what it appears to be, is one of the most important contributions to petroleum technology that has been brought out in the last 25 years. If his end products are what they seem to be, he has made. a discovery, which, in my judgment, will revolutionize the petroleum industry. As to industrially carrying out these processes I do not think there is the slightest difficulty, for I have had some work recently where crude oils were handled successfully at a temperature of 750" F, and pressure of 750 lb. per square inch. William A. WillIams, San francisco, Ca1.—What metal did you use, Mr. McLaughlin? A. C. McLauGHILIN.—Ordinaly seamless tubing, extra strong. William A. Williams.—Tests were made in Dr. Rittman's experimental plant at Pittsburgh, upon samples of residuum furnished by Mr. Bell, the residuum being the remainder of the crude oil after the lighter fractions had been removed. After the material had been run through Dr. Bittman's plant, yields of from 43 to 58 per cent. of material, boiling under 150" C. were obtained. The distillate had a peculiar odor, due to the presence of benzene, toluene, and other unsaturated hydrocarbons. W. N. Best, New York, N. Y.—What is the difference between the Rittman and the Snelling process or system? William A. Williams.—he fundamental difference is that reactions take place under relatively higher temperatures and pressures and with none of the oil present in its original or liquid state, while the reactions secured by Mr. Snelling and other investigators have been from the liquids in the presence of some vapors. Under such conditions as Mr. Snelling operates, the temperatures and pressures used are limited and the flexibility in the control of these variables is extremely limited when compared with the Rittman process.

Jan 1, 1916

By N. Cabrera

IN a recent paper Kuczynski' studied the rate at which the crack between a metallic plane and a spherical particle of the same material is filled up gradually when heated at temperatures near the melting point. If x is the radius of contact between plane and sphere (fig. I), Kuczynski shows experimentally that x5 = At [1] where t is the time. Assuming that the mechanism of transport of matter is the volume diffusion of vacant lattice sites, he is also able to prove Eq 1 theoretically. The constant A contains as a factor the self-diffusion coefficient of the metal and he shows that the values for this coefficient deduced from his experiments yield the same activation energy as that calculated by other methods, which is a confirmation of this point of view. Kuczynski has also considered theoretically the law of growth of x which would be expected if surface diffusion were the important mechanism. He suggests that x should then obey a law of the form x7 = At, and claims to be able to decide the mechanism involved from the observed law of growth., The purpose of this note is to prove this incorrect. On the contrary, when the mechanism is surface diffusion Eq 1 is also obeyed, but with a different constant A. Following Kuczynski, we suppose the bottom of the crack (surface A A) to have an average radius of curvature p. As a result of this curvature the concentration of adsorbed atoms in this surface, n(p) per cm2, will be smaller, and the concentration of vacant lattice sites in the neighborhood, N(p) per cm3, will be larger than the corresponding concentrations, n(w) and N(w), for a flat surface. For all practical cases we can write Thomson's formula in the form n(co)— n(P) N(P)—N(cc) _ 2a-a" n(oo) JV(co) kTp [2] where u is the surface energy of the metal and a the interatomic distance. 1. Let us now consider the mechanism of surface diffusion. We suppose the concentration of ad-

Jan 1, 1951

By Joseph H. Taylor

The Ducktown district is in the extreme southeastern corner of Tennessee, its principal railroad point being Copperhill, on the Blue Ridge division of the Louisville & Nashville Railroad, midway between Knoxville, Tenn., and Atlanta, Ga. The ore deposits were discovered about 1849 and development work was begun in the early fifties. Only the "black copper" ores, products of secondary enrichment, from beneath the gossan outcrops and overlying the massive sulphide deposits, were then mined and smelted for their copper content. Upon their exhaustion, attention was directed to the treatment of the pyritic ore remaining, resulting in the devising of a process consisting of open-heap roasting, followed by blast-furnace smelting, which was practised until 1903, when semi-pyritic smelting was adopted. In 1908, the companies operating in the district, on account of litigation brought about by alleged smoke damage to forests and vegetation in the adjoining counties of Georgia, were compelled to erect enormous acid plants to prevent the escape of the sulphur dioxide produced in the smelting operations. The utilization of this sulphur dioxide in the manufacture of sulphuric acid as a byproduct has added to the revenues of the companies, and at the same time has furnished a valuable source of supply of sulphuric acid to the fertilizer trade of the South, and more recently to the manufacturers of eyplosives for use in the production of war munitions. The steadily increasing demand for sulphuric acid for the manufacture of fertilizers and explosives, together with the decreasing imports of pyrites, from which the acid is generally produced, now makes it imperative that greatly extended resources of pyrite be developed. While the Ducktown deposits do not predominate in pyrite, they do contain an inexhaustible supply of pyrrhotite, admixed with pyrite, which can be satisfactorily employed to supplement or substitute for pyrite in acid making.

Jan 1, 1918

No records have been found of coal in the old Spanish documents, although some mention of it probably exists in manuscripts. Coal was found in Mt. Diablo, in Contra Costa County, about five miles south of the San Joaquin River in 1852, but the first mine, the Teutonia, was located in 1858. The deposits are located on both sides of a high ridge, and vessels of 1,000 tons burden could ascend the river to the nearest point to the mines.1 In 1854, coal was found about four miles from Oroville, on the Feather River, in Butte County. Development work was started and in 1856 a mine was opened. From the description the coal was likely a variety of lignite and probably never amounted to anything commercially, as it does not appear again in the records 2 The more valuable mines at Mt. Diablo were opened in 1859 and 1860. By 1867 there had been 11 mines started and at that time five were in operation. The seam conditions were much disturbed and lack of knowledge of them caused much waste of effort and money. All of the coal excepting that used locally and in nearby towns, was shipped to San Francisco, and largely used for steam purposes. The first receipts were in 1861-6,620 tons. A railroad to the river had been constructed and opened in February 1866. The Corral Hollow field in Alameda County was found and prospected to a small extent in 1862. Two mines were opened but little work was done and the field was then abandoned. Good exposures were rare and the cost of underground exploration was then prohibitive. The Commercial mine produced coal in 1869 and 1870, but a fire in the latter year destroyed the tipple and communications to the mine. The Livermore mine was abandoned after 18 months operation in 1875 and 1876 and no other work was done here until the nineties. In 1867 Hyne reported the presence of coal in workable thickness, and of good quality, on the property of the Pacific Coast Petroleum Company,

Jan 1, 1942

ALTHOUGH the committee appointed by the President of the American Iron and Steel Insti-tute, to consider the twelve-hour day work in the steel industry and report conclusions and recommenda-tions, has made a very careful and painstaking study of the facts and figures developed, it is not yet ready to make what it would designate a final report. Apparently the underlying reason for the agitation which resulted in the appointment of this committee was based on a sentiment (not created or endorsed by the workmen themselves) that 'the twelve-hour day was an unreasonable hardship upon the employees who were connected with it; that it was physically injurious to a large percentage of the employes; and that it interfered with family associations essential to the welfare of the children; that for these reasons it was, in a sense, opposed to the public interest. TWELVE-HOUR DAY NOT NECESSARILY INJURIOUS Whatever will be said against the twelve-hour day in the steel industry, investigation has convinced this committee that the same has not of itself been an injury to the employes, physically, mentally or morally. Whether or not, in the large majority of cases, twelve-hour men devote less time to their families than the employes working fewer hours is perhaps questionable. A part of the manufacturing of iron and steel is necessarily continuous. Therefore, practically, there must be two shifts of twelve hours or three shifts of eight hours. The workmen, as a rule, preferr the longer hours because it permits larger compensation per day. It is asserted with confidence that there is less phys-ical work, as a total per day, and less fatigue from the work of the twelve-hour day in the steel industry, than pertains to the large majority of the eight-hour men. This is because in the former case there are more rest periods during the twelve hours on duty.

Jan 6, 1923

By G. Bassi

RECENTLY Wallbaum¹ found that copper wires with different degrees of deformation up to 98.7 pct area reduction recrystallize giving a [112] texture, while deformation over 98.7 pct gives either a [l00] texture at low temperatures or a [1ll] texture at high temperatures. Furthermore it was found that the recrystallization temperature as a function of deformation up to 98.7 pct decreases as expected, but increases over that deformation. Wallbaum concluded that the different textures have different recrystallization temperatures. The [112] texture has the lowest and [Ill] the highest. At the same time Bassi² found that for high deformation (over 99 pct area reduction) and for an annealing temperature of 400°C, the [l00] texture first forms and with prolonged annealing time the [12] texture appears through grain growth. This secondary texture does not appear if the wire is annealed at 1000°C before the deformation. From these two papers it might be concluded that the [I12] texture can appear either as a primary or as a secondary texture after annealing. The texture formed in a special case depends on the previous history of the wire. Probably the texture of the wire prior to the last deformation is important. To investigate this, wires were produced by adequate deformation and annealing to give a [l00], a [112], and a [lll] texture. The wires then were given a series of different deformations and were annealed at various temperatures, after which the textures were studied. Experimental Work The copper used was electrolytic tough-pitch (Cu 99.90 pct and 0, 0.04 pct). Three wires with the different initial textures were made in the following way: The [l00] and [112] by drawing a 16 mm rod to 1 mm and annealing it 16 hr at 200°C and 2 hr

Jan 1, 1953

By Thomas M. Drown

In the course of some experiments on the analysis of pig iron, I heated, in a platinum crucible, some borings of a graphitic pig iron with sodium carbonate. When the crucible was at a full red heat and the carbonate was thoroughly fused, I noticed a lively ebullition of the mass, and an escape of gas, which burned on the surface. On investigation this gas proved to be carbonic oxide, and on examining the borings in the bottom of the crucible after an hour or two, they were found to be perfectly malleable, although unchanged in general form and appearance. Analysis showed that the carbon was completely removed. I then repeated the experiment, to ascertain whether the silicon and phosphorus were affected, and found that these elements too were largely removed, and could be .found in the fused mass as alkaline silicates and phosphates. In order to ascertain whether the removal of the silicon and phosphorus was merely a surface action or whether the reaction really extended into the mass of the iron, I tried the following experiments : A number of bars of pig iron were cast about one foot long and planed down 'accurately to one inch section. These were immersed in a large wrought-iron pot full of molteu sodium carbonate made by fusiug the commercial bicarbonate of soda. Through the kindness of Mr. Frank Firmstone, Superintendent of the Glendon Iron Works, Easton, I was enabled to keep this pot at a reasonably constant high temperature for a long time in one of the hot-blast ovens. One of the bars was removed from the pot every twenty-four or forty-eight hours, according to the rapidity of the action, and after cooling mas broken and the fracture examined. The change from pig iron to malleable iron was progressively inwards and always sharp and easily recognized, the rate of progression being in a decreasing ratio with the time. The temperature of the oven had evidently

Jan 1, 1879

By R. A. Deju, R. B. Bhappu

The theory of electrophoresis is briefly outlined and an apparatus which may be used for electrophoretic studies is explained. The results obtained using this apparatus are in agreement with those obtained by other investigators. How to solve some of the complications which occur in the measurement of zero charge and zeta potential is explained. It is believed that the apparatus described in this paper will allow rapid measurements of zeta potential, zero point of charge, electrophoretic mobility and zeta coefficient. For many years the phenomenon of electrophoresis has been studied, and much work has been done in designing an apparatus for better measurements of mobility, zeta potential and zero charge of minerals. Up to the present, most electrophoresis experiments have involved cumbersome equipment and tedious microscopic observation. The modified cell proposed in this paper obviates these drawbacks by using a Rayoscope together with a special system of lenses and filters. It therefore allows a faster and more accurate measurement of zero charge and particle velocity. THEORY Most authors currently regard zeta potential as the potential difference in an otherwise uniform medium between a point some large distance from the surface of the mineral and a point on the plane of shear. Fuerstenau,1 Miaw,2 and Gaudin and sun3 have performed some calculations of zeta potential using Henry's equation.4 Their results show wide discrepancies, probably due to differences in the past histories of the minerals used. The authors have also noticed this difference on determining the zero point of charge of quartz as shown on Table I.

Jan 1, 1967

By Jorge Munoz Reyes

There are three main oil areas in Bolivia (Fig. 1) although so far only one has yielded petroleum in commercial quantities. The Sub-Andean zone is along the easternmost ranges of the Andes, bordering the large eastern and northeastern lowlands. It extends from the Peruvian frontier, north of Lake Titicaca in a southeasterly direction towards the city of Santa Cruz and from there southward to the Argentine border. This zone forms a belt about 1200 km. long by 100 km. wide, and comprises a series of parallel, very rugged, low ranges. Oil has been known and utilized by the natives in these regions since colonial times, from the large number of seepages, which in modern times have led to the discovery of many fields. The second oil zone of Bolivia lies along the eastern and southern borders of Lake Titicaca, on the Andean high plateau, at an average altitude of 13,000 ft. above sea level. It comprises an area of approximately one million hectares (2,470,000 acres). Several seepages are known here, but little development has taken place, because of the difficulties encountered, as the greater part of the territory is covered by volcanic tuffs and ashes, which conceal the structure underneath. The third area is called the "Central zone," and is in the heart of the country, in the Department of Cochabamba, covering approximately five million hectares (12,350,000 acres). This area consists mainly of broad valleys flanked by low rolling ranges. Natural seepages are not known to exist, but there are secondary evidences of the presence of oil. The outcropping rocks are mainly Paleozoic (Silurian and Devonian sandstones and shales). Albertite and other forms of polymerized petroleum have been found in this region. Of these three main oil areas, only the first one is at present productive on a small commercial scale. This zone, developed almost exclusively by the Standard Oil Co. of Bolivia, a subsidiary of the Standard Oil Co. of New Jersey, is divided from south to north into the following local fields: 1. Bermejo (On the Argentine border) 3. Sanandita 5. Camatindi 2. San Telmo 4. Caigua 6. Machareti

Jan 1, 1935

By W. H. Andrews

The constantly increasing consumption of Portland cement in the State makes the above subject of particular interest at this time. The increasing demand is due to the rapid settling of the country and the fact that new uses are being found frequently for the above named commercial article. The industry is one that is bound to grow as the population increases, and this being the case it may be well at this time to consider briefly the matter of the chemical and physical composition of proper raw materials. A cement mixture is one that contains approximately 75 per cent, carbonate of lime, 15 per cent. silica, and 5 to 7 per cent. alumina and iron oxides; the other elements being magnesium carbonate and mall quantities of the rarer elements generally associated with limestone deposits. It can be readily seen from the above composition that it is possible to build up this mixture from a number of different materials. First.—A rock high in carbonate of lime can be mixed with clay or shale in such proportions as to bring about the desired composition ; the chief difficulty in the building up of such a mixture is that it is hard to find a clay or shale in which the silica-alumina ratio lies between 4 to 1 and 3 to 1 and at the same time shows physical characteristics which will make certain its adaptability to the practical manufacture of Portland cement. Very often clays or shales are found which are right chemically but contain large quantities of grit or free silica. Such clays or shale must be ground to extreme fineness in the mixture in order to make the silica and alumina combine with the lime when the mixture is burned. On the other hand, clays or hales are often found that have the proper physical characteristics but in which the amount of alumina is too great. Second.—A mixture can be built up of different limestones some of which run above the 75 per cent. requirement and others below;

Jan 1, 1914

By V. H. Gottschalk, R. S. Dean

In the theoretical study of metallurgical reactions, it is necessary to make certain assumptions concerning the nature of metal-gas systems. The assumption usually made is that the reaction in such systems takes place predominantly with gas that is in "solution" and that the amount of solution follows the rules which have been developed for aqueous solutions; namely, Henry's law. The purpose of this paper is to inquire whether these assumptions are the best ones that present knowledge of gas-metal systems permits us to make. In the first part the extent to which a gas will dissolve in a metal and still follow Henry's law is considered. The conclusion is believed justified that the number of molecules of gas that can dissolve in a metal and have the system follow Henry's law must be small indeed. It is therefore improbable that the first assumption concerning the predominance of these dissolved molecules in reaction is correct. It is suggested that some improvement in the correlation of the probabilities with the assumptions made in the mass law equations would be made by the use of the dp law of Sieverts in place of Henry's law. However, the amount of gas that may be held in a metal so that it follows either Henry's or Sieverts' law is considerably outweighed in most metallurgical reactions by that held in gas-metal systems of entirely different structures and concerning which little experimental evidence is available. Some speculation concerning the nature of these is offered. The conclusion is that attention should be given to the determining of the nature of gas-metal systems and that the really fruitful application of the mass law and its connected calculations will have to await a more complete knowledge of these systems than we now possess. DISCUSSION (Paul D. Merica presiding) P. D. Merica, New York, N. Y. (written discussion).—The solubility relations of gases in metals, in so far as they are known from the pioneer work of Sieverts and others, have from the first presented certain challenging peculiarities. The authors have emphasized the significance of these characteristics and suggest that they point

Jan 1, 1933

By H. l. Burghoff, A. I. Blank

J. J. Kanter.*—The authors of this paper have demonstrated that at 500°F their alloy will elongate, under appropriately adjusted stress, one or two per cent over a period of 6000 hr. Then they show that after the alloy has so elongated, it will still elongate anothcr 40 per cent if it is tested at ordinary temperature. I should like to ask the authors how much more than 2 per cent over a period of 6000 hr. their alloy will elongate at 500°F. H. L. BuRghofE.—We do not know, because we have not carried out stress-rupture tests on this material. I believe your point concerning the desirability of stress-rupture testing is very well taken. In the material that we have subsequently tested we have not seen any signs of deterioration. We do not know how much further it is possible to go beyond the 2 per cent before finding grain-boundary separation. We have not encountered any under the conditions of the test. W. E. Kingston.†—IS this particular type of copper susceptible to strain-aging, and if so at those comparatively low temperatures, is that going to affect the shape of the curve? By strain-aging I mean the phenomena that certain ferrous alloys show in which the resistance to deformation increases suddenly during the low-temperature creep cycle, apparently due to some precipitation type of reaction, perhaps analogous to hydrogen embrittlement. H. L. BUrghoff.—I believe that this material is not subject to strain-aging of this type. It is very high in copper content, of course, nearly loo per cent. There are some very minor impurities and it carries a small amount of phosphorus, which, unless it is present as an oxide, should be in solid solution well within the solubility limits. I believe it does not precipitate

Jan 1, 1945

By R. L. Langenheim

Cooperative education for engineers is based on the premise that theory and practice are inseparable in training men for the engineering profession, and the two must be advanced simultaneously in order to train men most successfully and efficiently. The teaching of theory obviously should be done by the college but the practice must be obtained in the field where the application of the theory is made. The ideally trained engineer is one that knows theory, can apply the theory to practice, can direct, and work with, his fellow men. The old four-year plan of training engineers does a fair job of teaching the underlying theory of engineering but neglects entirely the training necessary for application of the theory, except through laboratory experiments, and the training in adjustments necessary to direct and work with men. An engineer, like a lawyer, doctor, dentist or other professionally trained man, cannot practice until he has had practical experiences that give him a knowledge of the other phases of his profession. The doctor serves as an interne, the lawyer reads law in the office of a practicing attorney, and the engineer must enter the profession as a laborer or as an apprentice, unless he has had the advantage of a cooperative education. Cooperative education provides the opportunity for the coordination of practical and theoretical training for the engineering profession throughout the period of training and thus eliminates many that are unfit to enter the profession, giving them an opportunity to seek other fields for which they may be better fitted, and reduces the overhead in industry that results from a large turnover of men not fitted for the profession. The Cooperative Plan Cooperative education in engineering is no longer an experiment. It was inaugurated at the University of Cincinnati in 1904 by Dean Herman Schneider, and has worked successfully ever since. Over twenty schools offer this type of education and many thousands of young men have had the opportunity to receive their technical training under this plan. Under the cooperative plan a student attends class for a period of eight weeks, then enters industry for eight weeks, maintaining this schedule

Jan 1, 1937

By Nichols J. Grant, Bill C. Geissen

In low temperature phase diagrams, liquidus curves below about 1500°C are relatively easily established, e.g., by thermal analysis or separation of coexisting solid and liquid phases, followed by chemical analysis. Experimental difficulties increase considerably at higher temperatures and in systems involving more reactive metals. Although there are now thermocouples available for use from 1600" to 2400°c, as summarized by Caldwell,' the need for frequent calibration, aging, and contamination problems, and unavailability of suitable protection tubes has sharply limited their use at higher temperatures. Many of the high melt- ing metals are found to react with refractory oxides. TO avoid such problems, a frequently used procedure is the diffusion and saturation method, as described by Spedding et a1.' for the system La-C. This technique involves the annealing of one metal or a suitable alloy in a crucible of the other element at a temperature above the melting point, followed by chemical analysis of the center of the melt, after equilibrium is established. Further, if an alloy system is to be investigated employing the electron microbeam probe, and calibration charts have been established, it may be possible to measure the alloy concentration at the center of a cored as-cast structure, and to conclude from this points on the liquidus curve in a manner similar to the one to be described. It is known that in phases with a broad homogeneity range the rapidly cooled, cored, as-cast structure of an alloy presents concentrations having different lattice constants; this spread of lattice constant values contributes to the broadened lines of a powder pattern for the as-cast condition. The region of the crystal which is first to solidify will then correspond to the edge of the lines if the change of the lattice parameters with concentration is monotonous. In the course of the determination of the Ta-Tr phase diagram,3 it became evident that such behavior made it possible to construct the

Jan 1, 1963

By Charles H. White

+1HARVARD UNIVERSITY, CAMBRIDGE, MASS. The equipment of a laboratory in which students are to be trained for practical work in metallurgical chemistry presents many difficulties not encountered in the fitting up of a commercial or works laboratory. At an industrial plant the chemical work required usually demands the frequent repetition of a comparatively limited number of methods. In a steel-works laboratory, for instance, by far the larger part of the work consists in making determinations of the usual impurities found in iron and steel; at a smelter the great bulk of the work is confined to the analysis of ores, slags, mattes, and fuels, which involve the frequent application of perhaps not more than a dozen different methods. In a laboratory of this character, therefore, those operations most frequently applied may each have a certain section set apart and fitted permanently with such apparatus as best facilitates the carrying out of this one operation. The work of a commercial or custom laboratory is perhaps more varied than that of a works laboratory, but the couditions are similar in these respects, that there is usually no great need for economy of space, and that a few skilled workmen are employed to carry the determinations through from beginning to end without interruption. On the other hand, the laboratory of a technical school should be planned on such a scale that a comparatively large number of students may work at the same time, and each desk should be equipped for general metallurgical analysis. In most institutions for technical education the student's program is so arranged that his day is divided among several subjects in the course of study; only a few consecutive hours being devoted to one subject, or spent in one laboratory. Therefore, those appliances should be provided that render possible the safe continuation of such processes as

Jan 1, 1905

By George E. Roberts

The maintenance of the common gold standard is the most important cooperative undertaking in the world. The war broke up this relationship and brought about a state of great disorder in the currencies and exchanges. After the war the countries all began to grope their way back to the gold standard as the best means of establishing trade and financial relations with each other. With this movement began a general decline in commodity prices. The question has been raised whether the world's return to the gold standard was not forcing prices back to the prewar level. Also, the question is raised whether the world has not outgrown the supply of gold as the basis of credit. Because Europe readjusted its monetary units to conform to the higher level of prices there is no pressure on prices on this account. Furthermore, a large amount of gold formerly in hand-to-hand circulation passed out of circulation and has been added to the central bank reserves. The gold reserves of 36 countries increased approximately 100 per cent from the outbreak of the war to June 30,1930. The increase is much larger than the average increase of prices in any of the important countries, at any time since 192.5. As gold in the central banks of issue is far more effective for all business purposes than gold in circulation, the gold scarcity argument has little basis as applied to this time. The abnormal distribution due to the war was to the disadvantage of business everywhere. Credit was scarcer and dearer in some countries. The inflation in this country might have been greater had the production of gold been greater. The argument supporting the theory of a scarcity of gold assumes as fundamental that general price changes must be accounted for by changes in the price equation on the side of money. This is disproved in every period of business depression. A downward price movement is characteristic of every period of business recession. Important discoveries of gold must be made even to maintain present gold production, in the face of which the world's business is bound to continue increasing. It cannot be doubted that some way will be found

Jan 1, 1931

By Kendall E. Born

PRoduction of crude oil in Tennessee during 1938 was slightly more than 41,000 bbl., an increase of about 5000 bbl. over 1937. The production by counties and by fields is shown in Table 1. The increased production has resulted from continued activity in the Upper Cumberland district, especially in Clay County. The "Mississippi lime" production in Scott and Morgan Counties continued to show a further decline with a 1938 production of 12,379 bbl. as against 14,644 bbl. during 1937. Small scattered production from some half dozen wells in Clay, Pickett, and Fentress Counties, on which there are no accurate figures, is estimated at 500 bbl. during the year. The only natural gas marketed off the lease in Tennessee during 1938 was in Morgan County, where a small amount was furnished for the town of Sunbright and immediate vicinity. The gas occurs with the oil in the Boone Camp field and small amounts were put on the line from the near-by Coon Hollow and Seabolt pools. Developments There were 88 wells spudded in during 1938, of which 10 were drilling or only temporarily shut down on Dec. 31, 1938. Eighty wells were completed during the year; 16 produced oil and 3 were gas wells of undetermined quantity. The total footage drilled on 1938 completions was 63,385 ft. Flush production during the year totaled 850 bbl. per day. The more important wildcats are listed in Table 2; the distribution of oil and gas tests drilled during the year, according to physiographic divisions, is given in Table 3. Cumberland Plateau There were no completions in the producing pools in Scott and Morgan Counties. The decline in production in these areas has been steady for the past several years. In an effort to revive production, present plans include a repressuring program in the Boone Camp field in Morgan County early in 1939. There was one completion in Morgan

Jan 1, 1939

By J. Blodget Britton

IN the Journal of the Franklin Institute for May, 1870, there is published a description of a Colorimeter, together with a modification of the method proposed by Professor Eggertz, for determining combined carbon in iron and steel. An instrument of the kind there described, but of a little higher range, though in other respects not differing materially from the one originally made and used in the Iron-Masters7 Laboratory, I now submit to your inspection ; and I propose, also, to make some determinations minations with it for the purpose of showing how quickly they may be made, and enabling you to form some judgment of what reliance can be placed in the results. Professor Eggertz proposed only a single standard, and the solution to be tested should be diluted to exactly correspond in color with that of the standard, and the per cent. of carbon calculated after carefully noting and making allowance for the measures of water used in diluting. In practice, difficulty was found in bringing the color of the normal solution down to the exact shade of the standard; also other difficulties were met with in conducting the process, causing delay and interfering with the accuracy of the results. To materially overcome these, and after numerous attempts, an instrument such as is now before you suggested itself to me; and also I concluded to use a larger quantity of metal than directed by Eggertz, and, in addition, to filter the solution from its insoluble matter before making the comparison; and, more recently, to use an acid of just such strength as would completely dissolve the metal without the application of heat. Experimenting with these changes from the original method I obtained reasonably good results. The instrument, you will observe, consists of a series of tubes, sixteen in number, two and a half inches long, and about half an inch in diameter, standing upright, and securely fastened in a light, portable, walnut-wood frame, but separated one from the other so as to allow just sufficient space between to place for comparison the . tube containing the solution to be tested. The tubes are filled with

By T. F. Adams, D. P. Morse

Tunneling is primarily an excavating cycle consisting of a sequence of operations: drilling, shooting, ventilating, mucking, and erecting supports, if necessary. However, the type and condition of the ground that is being worked, as well as the size and shape of the tunnel, determine the rate of advance. In addition developments in drilling, ventilation, mucking, and haulage equipment have contributed to faster tunneling. Geology: This discussion will be limited primarily to rock tunnels or those which require the use of explosives, and the cost and hazards depend primarily on the condition of the rock which may be broken, decomposed, and contain water with gas. Advance geological study is an important part of any tunnel work and helps to minimize serious miscalculations. The geology itself, at best, is a matter of experience and prediction and it is not so much a matter of the types of rock the tunnel may go through, but a knowledge of the class and intensity of the rock defects that may be encountered.

Jan 4, 1958