Search Documents

By P. W. Ramsey, E. J. Boyle, E. A. Anderson

Only a few zinc-rich alloys are in commercial use today, and these depend largely upon solid solution effects for their desirable properties. Typical examples are rolled alloys containing about 1 Per cent of copper, with Or without additions of elements such as magnesium, and die-casting alloys containing about 4 Per cent of aluminum with small amounts of magnesium and sometimes copper." A number of elements are capable of forming alloys with zinc, Which do not enter into solid solution except in limited degree. The Present Paper considers One such system, zinc-titanium, in which alloys having potentially useful properties in the rolled form were found. Zinc-titanium System The zinc-rich portion of the zinc-titanium diagram, as determined by standard methods in this laboratory,3 is shown in Fig. I. The portion of the diagram of significance in the present work extends from 0 to about 0.5 per cent titanium. Gebhardt4 places the eutectic at 0.45 per cent, but the evidence in favor 01 the composition given in Fig. I is considerable. The solid solubility of titanium in zinc is very low indeed and possibly places these alloys in a somewhat different category from the commercial alloys previously mentioned. Alloy Preparation All of the alloys used in this work were prepared with titanium metal of 98.9 per cent purity. In most cases high-purity zinc (99.99 per cent) was used but sufficient work was done later to show that zinc of about high-grade composition would yield approximately equal results. Best practice in alloy manufacture seemed to be to prepare a zinc-titanium hardener by adding about 4 per cent of titanium metal to molten zinc and holding under a boric acid cover, with frequent stirrings, at 750°C, until the titanium had dissolved. The desired titanium content could readily be obtained in the final alloy by adding the calculated amount 01 this hardener. The alloys proved to be quite stable in composition, unless overheated, and, with reasonable temperature control, required no cover or flux to prevent loss of titanium content by oxidatioll, Hot-rollig Tests Three alloys containing, by analysis, 0.05, 0.12, and 0.23 per cent titanium were selected for preliminary study. Slab cross sections a a marked grain refinement* (Fig. 2) in the two alloys of highest titanium content. Cast unalloyed zinc has a columnar grain structure similar to that shown for the alloy of lowest titanium content but without the scatter of small equiaxed grains at the center.

Jan 1, 1944

By Paul M. Tyler

Mineral raw materials, because they are essential to our industrial prosperity and military strength, must be made available in substantial quantities regardless of cost. Variations in the cost of procuring minerals, as compared with the cost of obtaining other commodities, and changes in the cost of production of different minerals relative to one another, will naturally influence the quantities of a given mineral item that can be marketed readily. However, in the last analysis, the cost of winning minerals from the ground usually constitutes only a small fraction of the value of the end-use products and services derived from them. The miner's share of the cost of a typewriter, telephone circuit, or even a modem office building, is almost insignificant. Far more important to the ultimate consumer, therefore, than any minor saving in cost is the assurance of ample supplies of the minerals needed to aliment our expanding economy. To create a successful metal mining operation involves (1 ) the discovery and systematic development of a mineral deposit, (2) extraction of the ore, (3) the mechanical and metallurgical processing to eliminate worthless or harmful impurities, and (4) the profitable disposal of the product. The fist step of the technological process belongs chiefly in the realm of the geologist, the second is a mining engineer's job, the third is mainly up to the millmen and extractive metallurgists; whereas the fourth and equally important step poses a commercial problem that has aspects in common with the marketing of other products. Ore finding is far from being an exact science. There is no mathematical criterion for evaluating the efficiency of prospecting and exploration. Lady Luck shares the honors or assumes part of the blame along with the prospector and geologist. Marketing like- wise involves factors that seemingly defy engineering analysis. Although the other steps can be measured with some degree of mathematical accuracy, even they tend to vary so widely in basic principle, as well as in

Jan 1, 1964

By L. A. Schrider, J. A. Wasson

A method of predicting waterflood performance has been developed that combines certain facets of several previously published prediction techniques. The manner of combination has required the development and use of some new and some little-known relationships and has eliminated several of the weaker assumptions inherent in the original individual prediction methods. This approach, which was designed for computer solution, has removed the necessity of referring to plotted curves and permits the analytical prediction of water flood performance for a five-spot well pattern in either homogeneous or stratified reservoirs. The Predicted values are expressed in common oilfield units rather than in abstract or dimensionless terms. The calculation procedure has been programmed in FORTRAN IV and the entire program listing is available to potential users.* Introduction Prior to initiation of secondary recovery of oil by waterflooding, the possibilities of economic success or failure must be evaluated with the greatest practical accuracy. Although many prediction techniques are available, most, if not all, have serious limitations. In recent years, the Bureau of Mines has attempted to stimulate interest in the secondary recovery of oil from Appalachian pressure-depleted reservoirs. Waterflooding, because of its widespread acceptance and success, is the principal secondary-recovery method considered. During the life of the project, several performance prediction methods have been studied and applied. Because these methods, individually, have inherent assumptions and limi-tations, portions of some of them have been selected and combined in an effort to eliminate such shortcomings wherever possible. We believe that the resulting technique is as accurate as the necessary available data will permit and that it has several distinct advantages over previously published methods. Development of the Method The fractional flow equation developed by Buckley and Leverett' from Darcy's law is the fundamental mathematical statement describing immiscible fluid-fluid displacement in porous media. A generalized form of this relationship, whose derivation is readily available in the literature, is The formation dip, a, is usually very small in those petroleum reservoirs being considered for pattern waterflooding in the Appalachian area. Therefore. in many cases. a has an almist negligible value. In addition, Ap, the difference between the density of water and the density of oil, is relatively small. For these reasons the gravitational term may often be neglected. Capillary pressure is a function of saturation, which is in turn a function of distance from the upstream boundary of the system or the injection well. In this study it is assumed that the frontal zone of the waterflooding (or zone of capillarity) has negligible length and that only those saturations in the water-swept zone at breakthrough and later are of interest. As the distance in a waterflood pattern is comparatively large and the change in water saturation with distance is usually small, the change in capillary pressure with distance is negligible. The simplified form of the fractional flow equation is appropriate, therefore, in this application. Three variables must be considered in determining that fraction of the total fluid flow that consists of water: the viscosity ratio, saturation, and relative permeability ratio.

Jan 1, 1969

By Carl Benedicks

IT is well known by every one who has had to deal with boiler tubes that these are often seriously affected by a sort of corrosion, occurring as a local pitting, that frequently causes a perforation of the tube in a rather short time. The characteristic appearance of this corrosion is shown in Fig. 1. A very similar corrosion occurs in condenser tubes (Fig. 2).1 A study of the microstructure or local chemical composition of the metal (iron; 70 :30 brass) fails to reveal any cause for this pitting. Of course one might possibly assume the starting point-to be some oxide particle, causing an electrolytic local action, but this in no way explains the continued corrosion, progressing even when the assumed oxide particle must have disappeared. By the excellent work done by the Corrosion Research Committee of the Institute of Metals, and communicated, in October, 1923, to the Institution of Engineers and Shipbuilders in Newcastle-on-tyne, stress was laid on the fact that a content of entangled air has a very obnoxious effect. In the following correspondence, Sir George Goodwin stated that "engineers have, for a long time past, regarded air as the big enemy to be fought against in all questions of corrosion"2 and Kenneth Fraser pointed out that the most vital point is "the avoidance or removal of possibly the chief cause of present day corrosion, i. e. entrapped air and gases brought out of solution."' In their reply, however, the authors state that they had "never for a moment believed that entangled air was responsible for the beginnings of corrosion, and express the opinion that the gradual liberation of air could not account for localized corrosion."4 On consulting the many textbooks on corrosion, as that

Jan 4, 1925

By Milton Williams

A comparison is made between the amount of interstitial water found by analysis in cores and that estimated from the resistivity curve of the electric log for the corresponding strata of producing reservoirs. It is shown that while the determined and the estimated water saturations are in good agreement in some cases, this agreement may be due to a fortuitous compensation of errors. Estimates of water saturations made from the electric 1og by use of existing relations should, therefore, be employed with caution. Also presented are data on the variation of salinity of interstitial waters in reservoir sands, and on the effect of variation of salinity and porosity on the validity of estimates of water content made from the electric log. INTRODUCTION Throughout the history of electric logging there have been recurrent cycles of optimism and pessimism as to the value of the electric log in the quantitative estimation of reservoir fluid content. The very early days of electric logging were an optimistic period, in which there was widespread faith in the ability of the resistivity curve to reflect fluid content, and in the ability of the potential curve to indicate textural characteristics. In time the accumulation of exceptions to this idealistic behavior brought about a general disillusionment, and caused the more pessimistic of those dealing with electric logs to believe that the sole importance of the log lay in stratigraphic correlation. Within the last several years optimism as to the quantitative use of the electric log has been revived, primarily as the result of the stimulating work of C. E. Archie' on the estimation of interstitial water in sands from resistivity data. Even though the general trend of thought on the quantitative value of the electric log reflects optimism, it is inevitable that there are some widely divergent opinions of the validity of quantitative estimates based on the electric log. A valid method of estimation of fluid content by means of the electric log and a general knowledge of the textural character of the reservoir rock would be of signal importance, not only in that it would save time and money in securing information on reservoirs now being drilled, but also because it would permit the evaluation of reserves in many fields drilled without adequate core data subsequent to the advent of electric logging. Because of this importance, Humble's Production Research Division, in cooperation with various other company divisions, initiated several years ago series of tests designed to evaluate the reliability of estimates of fluid content made from the electric log. The investigation was limited at the outset to sand reservoirs, since it was felt that the inclusion of limestone reservoirs would entail needless complications. In devising these tests it was immediately apparent that the chief difficulty in evaluating the worth of any method of estimation lay in establishing the true value of fluid content. The results of direct analyses of cores cut with ordinary mud were not sufficient, because of the probability of contamination of the fluids by filtrate from the drilling mud; the results of restored state tests on cores were deemed unsuitable because these results can hardly be said to furnish a primary standard. The method adopted was the direct analysis of cores cut with an oil-base drilling fluid. Such cores, when properly handled, are believed to afford the most precise determination of water content available at the present, and, in addition, lend themselves readily to the determination of various other properties which are pertinent to the estimation of fluid content from the electric log. Since it was desired to compare the fluid contents estimated from the electric log run in ordinary mud with cores cut in the same hole, the use of oil-base fluid necessitated the changing over, after all cores were cut, to a conventional mud. This procedure presented several advantages, one of which was that the use of oil-base fluid permitted

Jan 1, 1950

By John F. Elliott

STAFF: Editor, Gerhard Derge Acting Editor, Poul G. Shewmon Carnegie lnstitute of Technology Schenley Pork Pittsburgh 13, PO. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Rich-ard C. Cole, President; Karl L. Fetters, Past-President; J. H. Scoff, Vice President; R. L. Henneboch, Treasurer, R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. E. Lund, Chairmon; T. E. Dancy, P. R. Gouwens, W. A. Krivsky, F. C. Longenberg, E. R. Morgan, R.R. Nosh, Poul Queneou, W.O. Philbrook, J. H. Scoff, L. L. Seigle, and M. E. Wadsworth. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: M. E. Wadsworth, Chairmon; R. E. Grace, Vice Chairman; D. H. Baker, Jr., G. M. Bell, D. H. Bridges, J. M. Cigon, G. W. Healy, R. A. Lewis, C. E. O'Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iron and Steel Division: T. E. Dancy, Chairman; A. Muan, D.W. Murphy, R. D. Pehlke, J. M. Uys, J. 5. Wagstoff, and R. G. Word. lnstitute of Metals Division: R. R. Nash, Chairman, H. H. Johnson, Jr., Vice Chairman; M. R. Achter, P. A. Beck, J. J. Becker, G. F. Bolling, J. 0. Brittain, J. 8. Clark, R. 5. Davis, A. E. Dwight, R. W. Fountain, L. A. Girifalco, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, R. H. Richmao, H.C.Rogers, W. Rostoker, 0. D. Sherby. E. A. Steigawald, R. Steinitz, H. C. Stumpf, R. A. Swalin, W. A. Tiller, W. R. Upthegrove, D. Walton, H.W. Weart, and D. Wilsdorf. Published bimonthly by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc 345 East 47th Street, New York 17. N. Y. Telephone PLaza 2-6800. Subscription $30 per year for non-AIME members in United States and North, South, and Central America; $32, foreign;$30per $7 50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1963 by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc....Registered cable address, AlME New York . .. Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts . . Second class postage paid ot New York, N. Y., and Ann Arbor, Mich. Volume 227, Number 4.

Jan 1, 1963

By William Fink

ALUMINUM forms not only binary compounds with most of the metallic elements but also forms many ternary or more complex constituents. Several of those occurring in the more important alloy systems have been identified under the microscope and the action of various etching reagents has, been carefully studied.' The determination of the structure and composition of these complex constituents is a matter of some difficulty and little information is available. X-ray crystal analysis offers a promising method for the study of such constituents. First, and of considerable importance, is the possibility of recognizing the presence of a given constituent by means more positive than microscopic observation. Evidence can also be obtained concerning the nature and composition of the constituent in question and ultimately it should be possible, at least in some cases, to describe the structure including the relative locations of the various atoms. In this paper some results of an uncompleted study of the constituents of the aluminum-iron-silicon system are given and the methods employed are described. Inasmuch as iron and silicon are the chief impurities in aluminum, the constitutional relations of this system are of fundamental importance in the metallurgy of pure aluminum and its alloys; the system has been studied by several investigators and the more important contributions have been reviewed recently.2 Fig. 1 shows the structure of the aluminum-rich alloys after prolonged annealing at 560° C., in accord with one of the most recent investigations.3 The ternary alloys examined in the course of the present investigation were all annealed at 550° or 560° C.; in fact, some of the specimens were the identical ones used by Dix and Heath, who kindly supplied them for this work. Since the results

Jan 1, 1930

By Wm. R. Webster

This is a contribution for the proposed new discussion on the physics of steel. The former discussion on the subject started with the consideration of five papers presented at the Chicago meeting in 1893, and continued for several years. The Suggested Lines of Discussion, prepared by Doctor Howe, covered a wide field and added greatly to the success of the work. Naturally, the first step in a new discussion will be to remodel and bring up to date the old Suggested Lines of Discussion so as to embody all the important advances in the metallurgy of steel that have a bearing on the physics of steel and keep the papers and discussions within the field of work undertaken. This paper will be devoted to the practical application, in rolling steel, of the effects of carbon, phosphorus, and manganese on its tensile strength, with some suggestions on further research work. Dr. J. E. Stead, in his paper Influence of Some Elements on the Mechanical Properties of Steel,' gave a complete review of all that had been done during the past thirty years. He gave full credit to all investigators who worked on these lines, also their results, with his views on same, and in many cases his own results. All of this data and much new valuable information were put in convenient shape for reference and study. To do this required a great deal of work, which is fully appreciated by the steel manufacturers and investigators. The variations in the values given by the different investigators for the increase of the tensile strength of steel for each 0.01 per cent. of carbon, phosphorus, and manganese were largely due to the steels they worked on, the large or small variations in the amount of the elcments present, and the omission to take into consideration all the factors, from the blast furnace through to finished rolled material, that affect the character of the steel. For instance, a poorly made dirty steel requires considerably more carbon to give the same ultimate strength than a well-made clean steel with the same phosphorus and manganese content.

Jan 1, 1922

By Wm. R. Webster

This is a contribution for the proposed new discussion on the physics of steel. The former discussion on the subject started with the consideration of five papers presented at the Chicago meeting in 1893, and continued for several years. The Suggested Lines of Discussion, prepared by Doctor Howe, covered a wide field and added greatly to the success of the work. Naturally, the first step in a new discussion will be to remodel and bring up to date the old Suggested Lines of Discussion so as to embody all the important advances in the metallurgy of steel that have a bearing on the physics of steel and keep the papers and discussions within the field of work undertaken. This paper will be devoted to the practical application, in rolling steel, of the effects of carbon, phosphorus, and manganese on its tensile strength, with some suggestions on further research work. Dr. J. E. Stead, in his paper Influence of Some Elements on the Mechanical Properties of Steel,' gave a complete review of all that had been done during the past thirty years. He gave full credit to all investigators who worked on these lines, also their results, with his views on same, and in many cases his own results. All of this data and much new valuable information were put in convenient shape for reference and study. To do this required a great deal of work, which is fully appreciated by the steel manufacturers and investigators. The variations in the values given by the different investigators for the increase of the tensile strength of steel for each 0.01 per cent. of carbon, phosphorus, and manganese were largely due to the steels they worked on, the large or small variations in the amount of the elcments present, and the omission to take into consideration all the factors, from the blast furnace through to finished rolled material, that affect the character of the steel. For instance, a poorly made dirty steel requires considerably more carbon to give the same ultimate strength than a well-made clean steel with the same phosphorus and manganese content.

Jan 1, 1922

By Howard Scott, Henry S. Rawdon

The method of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallog-raphists. The usual procedure1 2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas (chlorine, hydrochloric acid or similar gas) for a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being admitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo. The studies of Rosenhain, Humfrey, and other workers 4, 5, 6, 7, 8 dem-

Jan 1, 1922

By Howard Scott, Henry S. Rawdon

The method of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallog-raphists. The usual procedure1 2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas (chlorine, hydrochloric acid or similar gas) for a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being admitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo. The studies of Rosenhain, Humfrey, and other workers 4, 5, 6, 7, 8 dem-

Jan 1, 1922

By Rossiter W. Raymond

Being a portion of the President's Address at New Haven, February 23d, 1875. As I have attempted briefly to show you, gentlemen, the present position of the mining and metallurgical industries of this country offers in several respects most important indications of radical change. This is an epoch for more than one branch of these industries. We are commencing again to export copper; we have shifted the main production of lead from the Mississippi Valley to the far West, besides developing a new production of that metal in Missouri; we have seen the price of quicksilver go up, and the price of iron go down to such an extent as to affect profoundly, on the one hand, the great business of extracting silver by amalgamation, through the Washoe process in this country and the patio process in Mexico, and, on the other hand, the various manufactures employing iron as a raw material ; above all, the manufacture of steel. But the epoch which has occurred in the relative value of gold and silver, in consequence of causes which I shall attempt to explain, and among which the extraordinary increase in the silver product of Nevada is not the least ; this epoch is, perhaps, the most striking feature in the review of our situation. Since my official duties in connection with the mining industry of the Pacific slope and the Great Interior Basin have led me to pay particular attention to this subject, I have thought it not inappropriate to lay before you a somewhat extended account of its history. It is a topic of peculiar interest, because of the general use of these two metals as standards of value in the exchange of commodities. Neither of them is suitable to be, for the political economist, a real standard of value. That standard is rather to be sought in some more universal product of labor, such as wheat-the relation

Jan 1, 1875

By Rossiter W. Raymond

As I have attempted briefly to show you, gentlemen, the present position of the mining and metallurgical industries of this country offers in several respects most important indications of radical change. This is an epoch for more than one branch of these industries. We are commencing again to export copper; we have shifted the main production of lead from the Mississippi Valley to the far West, besides developing a new production of that metal in Missouri; we have seen the price of quicksilver go up, and the price of iron go down to such an extent as to affect profoundly, on the one hand, the great business of extracting silver by amalgamation, through the Washoe process in this country and the patio process in Mexico, and, on the other hand, the various manufactures employing iron as a raw material; above all, the manufacture of steel. But the epoch which has occurred in the relative value of gold and silver, in consequence of causes which I shall attempt to explain, and among which the extraordinary increase in the silver product of Nevada is not the least; this epoch is, perhaps, the most striking feature in the review of our situation. Since my official duties in connection with the mining industry of the Pacific slope and the Great Interior Basin have led me to pay particular attention to this subject, I have thought it not inappropriate to lay before you a somewhat extended account of its history. It is a topic of peculiar interest, because of the general use of these two metals as standards of value in the exchange of commodities. Neither of them is suitable to be, for the political economist, a real standard of value. That standard is rather to be sought in some more universal product of labor, such as wheat—the relation

By R. Floyd Farris

Al thorough knowledge of the behavior of cement slurries under elevated temperatures and pressures is necessary in order to solve properly the many problems presented in deep-well cementing operations. In the earlier days of the petroleum industry the depths of wells were shallow as compared to those of today, and the subsurface temperatures and pressures were not of sufficient magnitude to affect seriously the problem of proper control of cement-slurry properties. Today, however, the search for new reserves has extended drilling to such depths that bottom-hole temperatures of more than 200°F. and bottom-hole pressures of 3000 to 5000 lb. are not uncommon. Moreover, there is every indication that within the next few years wells will be drilled to even greater depths and bottom-hole temperatures and pressures will be correspondingly higher than those with which we are concerned today. It has been realized for some time that the behavior of cement slurries at high temperatures and pressures might be very different from that at atmospheric tempera-ture-pressure conditions, but while the temperature effects have been investigated with a reasonable degree of thoroughness, the pressure effects have received little public attention. While the trend toward deeper drilling may make changes in cementing technique and the choice of cements imperative, it was the purpose of this investigation to consider factors having a bearing on the latter, only secondary consideration being ,given, for the present, to details of tech-nique and equipment for oil-field use. More specfically, the purpose of this work was to consider the effect of temperature and pressure upon the behavior of cement slurries. Although it has long been recognized that cements thicken and set rapidly with increasing temperatures, practical methods for the quantitative determination of these effects are comparatively recent developments. In 1935 Silcox and Rule1 presented such a method, describing apparatus designed to measure the consistency-time relationship of cement slurries at relatively high temperatures. The practical importance of this apparatus in furnishing useful data for the evaluation of cement slurries for cementing operations has been emphasized in various technical publications by such writers as E. L. Davis,~ I. F. Bing-ham,3 and J. E. Weiler.4 A paper describing the numerous tests now used to evaluate cements for oil wells was presented in 1939 by W. W. Robinson.= Robinson describes the Consistometer and the Thickening-Time Tester, showing similarity of data from the two devices, and points out that the purpose of each apparatus is to determine the allowable time that a cement may be pumped at a given temperature. At the present time, however, it is believed that results from the Thickening-Time Tester and the Consistometer have not given a

Jan 1, 1941

By R. Floyd Farris

Al thorough knowledge of the behavior of cement slurries under elevated temperatures and pressures is necessary in order to solve properly the many problems presented in deep-well cementing operations. In the earlier days of the petroleum industry the depths of wells were shallow as compared to those of today, and the subsurface temperatures and pressures were not of sufficient magnitude to affect seriously the problem of proper control of cement-slurry properties. Today, however, the search for new reserves has extended drilling to such depths that bottom-hole temperatures of more than 200°F. and bottom-hole pressures of 3000 to 5000 lb. are not uncommon. Moreover, there is every indication that within the next few years wells will be drilled to even greater depths and bottom-hole temperatures and pressures will be correspondingly higher than those with which we are concerned today. It has been realized for some time that the behavior of cement slurries at high temperatures and pressures might be very different from that at atmospheric tempera-ture-pressure conditions, but while the temperature effects have been investigated with a reasonable degree of thoroughness, the pressure effects have received little public attention. While the trend toward deeper drilling may make changes in cementing technique and the choice of cements imperative, it was the purpose of this investigation to consider factors having a bearing on the latter, only secondary consideration being ,given, for the present, to details of tech-nique and equipment for oil-field use. More specfically, the purpose of this work was to consider the effect of temperature and pressure upon the behavior of cement slurries. Although it has long been recognized that cements thicken and set rapidly with increasing temperatures, practical methods for the quantitative determination of these effects are comparatively recent developments. In 1935 Silcox and Rule1 presented such a method, describing apparatus designed to measure the consistency-time relationship of cement slurries at relatively high temperatures. The practical importance of this apparatus in furnishing useful data for the evaluation of cement slurries for cementing operations has been emphasized in various technical publications by such writers as E. L. Davis,~ I. F. Bing-ham,3 and J. E. Weiler.4 A paper describing the numerous tests now used to evaluate cements for oil wells was presented in 1939 by W. W. Robinson.= Robinson describes the Consistometer and the Thickening-Time Tester, showing similarity of data from the two devices, and points out that the purpose of each apparatus is to determine the allowable time that a cement may be pumped at a given temperature. At the present time, however, it is believed that results from the Thickening-Time Tester and the Consistometer have not given a

Jan 1, 1941

By Craig R. Barrett, Jack L. Lytton, Oleg D. Sherby

The types of substructures developed during high-temperature creep of (110)[001]-oriented polycrys-talline Fe-3.1 pct Si were examined by electroetching of dislocation sites. Edge dislocations were observed to accumulate adjacent to grain boundaries and poly-gonize perpendicular to their glide planes to form a "Pile-up" of nearly parallel tilt boundaries. The dislocation density developed within the grains during steady-state creep was found to increase with increasing stress. The formation of periodically spaced groups of edge dislocations along grain boundaries was observed, and it was proposed that these formed to relive bending stresses at grain boundary shear .faults. Grain boundary serrations developed at these faults, and it was suggested that this was a result of localized grain boundary migration at the polygonized groups. THE authors have conducted a series of high-temperature creep tests on (110)[001]-oriented poly-crystalline Fe-3.1 pct Si sheet. The creep specimens were examined at various stages of creep by means of electrolytic etching of dislocation sites using the chrome-acetic acid solution developed by Morris.' Hibbard and Dunn2 have demonstrated that the etch pits produced with this technique correspond to single dislocations. It is the purpose of this paper to present and discuss the dislocation substructures which were formed during high-temperature creep at constant stress. EXPERIMENTAL PROCEDURES The polycrystalline Fe-3.1 pct Si sheet employed in this study contained a (110)[001] texture. This texture was quite strong, and the elastic properties of the sheet closely approached those of a single crystal of iron.3,4 A typical analysis in weight percent for this material is 3.1 Si, 0.1 Mn, 0.003 C,

Jan 1, 1965

By Charles H. Addison, Robert W. Shields, James W. Sweeney

GIPSY: Is user oriented. Is flexible in applications. Is an ITERATIVE question answering system. Has an adaptable retrieval mechanism. Has both a batch and a teleprocessing version. Allows the user to "browse" through his information. Has ability to answer "ad hoc" queries. Is a currently working and proven system.

Jan 1, 1969

By G. B. Kasik, George Sachs, George Espey

IT has been reported frequently that the hardness and strength vary over the cross section of cold-worked, particularly cold-drawn, material. Brass rod and wire usually has been found to possess a maximum strength and hardness near the surface.1,2 According to Sachs,1 the center fiber has about the same strength as a wire stretched by the same amount in a tensile-test machine, the strength increasing toward the surface (Fig. I). These differences are particularly large for wire given a small reduction on drawing through a die with a wide opening. However, with increasing reduction and hardness, a tendency to form a thin soft surface skin becomes apparent. On the contrary, copper wire has usually been found to possess a soft surface skin" and it has been reported by Harris3 that during the cold-drawing of hot-rolled wire the surface layer becomes increasingly softer than the core, while the layer of maximum strength moves toward the core, it being found near the surface at first. The increase of strength and hardness from the core to the skin is readily explained by the observation that, in addition to the stretching, the layers of a rod or wire are sheared more the closer they are to the surface.1,6-8 However, the presence of a soft surface layer can be attributed only to an annealing effect. The source of such a softening might be the extremely high temperature that originates from the friction between [ ]

Jan 1, 1941

By N. J. Themelis, R. V. Flint

In a four-year period between 1973-76, the Metal Mining Division of Kennecott Copper Corp. conducted a company-wide program of operations improvement which involved line and staff personnel from all company functions. Specialist teams performed detailed studies of all operational aspects at Kennecott's four copper mines and concentrators, four smelters, and two electrore-fineries. The specific recommendations that resulted may transform the Metal Mining Division into the country's lowest cost producer of copper by the mid-1980s. In this article, N. J. Themelis and R. V. Flint describe the mechanics of MMD's integrated approach to operations improvement.

Jan 6, 1979

By Walter C. Lawson

THE primary objective in laying track in panel sections is to reduce the number of track laborers required. This is possible because the work is mechanized. Moreover, because the work is mechanized and each of the operations needs only a few men, and each is self-contained, the work can be carried on at night as well as in daylight; therefore, the method provides a means of preparing tracks on more than one shift. The laying of tracks in open pits and quarries in panel sections is not new but new methods have been made possible by the introduction of new types of equipment. The purpose of this paper is to describe the methods that are followed in' the Morenci open pit. GENERAL MINING OPERATIONS Full-scale ore production at Morenci is about 50,000 tons daily. The normal yearly output of ore and waste is 32,000,000 tons, of which 30,000,000 tons is handled by rail haulage. This requires the building of approximately 47 miles of loading and other temporary tracks during a 12 months' period (Fig I). Broken ore and waste, is loaded., into 90-ton capacity dump cars with 5-cu-yd full-revolving electric shovels. Shovel banks are uniformly 50 ft high:. They are blasted- with churn drill holes, and the broken material from a blast is loaded out with two shovel cuts, the first one being called (locally) the "splatter" cut and the second one the "clean-up" or "face-up" cut. When a shovel is making its clean-up cut, the loading track is about 70 ft from the toe of the bank and, under normal conditions, a bank is blasted against it without removing the track. It is thus evident that each track is used for two shovel cuts before relocation is necessary, inasmuch as a single position serves for both the clean-up cut prior to blasting and for the splatter cut following the blast. The normal advance of a solid bench by a single blast is 40 ft (Fig 2). PREPARATION OF PANEL GRADE In preparation of panel grades bulldozers and rooters are used for the bulk of the work and an auto-patrol road grader for the final stage. At Morenci, bulldozers have always been used for track-grade preparation, but before the introduction of the other two types of equipment grades were uneven and irregular at best, and always necessitated a big gang of track laborers to hand-block under the ties with rocks after a track was laid into place. High blocking also made poor track because of instability and caused frequent derailments. Under these conditions derailments were generally bad as re-railing became difficult. Much track was torn up and many ties broken in the process. The inadequacy of the hand-blocked track, together with the inefficiency of hand blocking, constantly pointed to the desirability of reducing the amount of labor required, so various means were tried to improve conditions, such as wood

Jan 1, 1947