Search Documents

By L. M. Barker, E. G. Lewis

The literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: 1. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the litera- ture of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others—a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis' criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis' conclusions and with improvement of ball-milling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1943

By J. W. Whalen

The design, operation and evaluation of an instrumental method for the determination of fluid saturation in porous materials during multiphase flow studies is described. The presence of a magnetic tracer comprising approximately 20 per cent by weight of the aqueous phase is necessary in the utilization of this method. The results of two-phase relative permeability studies on two samples of porous media are presented. The realizable accuracy of the magnetic susceptibility apparatus in fluid saturation determination is estimated to be 2 saturation per cent. The response characteristics of the instrument, together with its simplicity of operation and maintenance are sufficient to recommend its use in routine laboratory studies. INTRODUCTION The problem of fluid saturation determination in laboratory multiphase flow studies characterizing oil recovery processes is one which has been given exhaustive study. Briefly the requirements which are considered essential for a method sewing this purpose are: (1) that the measurement be made external to the porous rock sample under study with no interruption of the fluid flow pattern, (2) the saturation indication must be independent of fluid distribution in the volume scanned by the measuring device, (3) the sensing element should have a small field of definition enabling several independent measurements to be made along the length of a core sample, and (4) the properties of the fluid phases should not be too greatly influenced by required tracer substances. Several methods of saturation determination have found acceptance as meeting most of the above requirements. These include resistivity,1 X-Ray absorption,2,3,4 radiotracers,5,6,7 and neutron8 diffraction The merits of these techniques have been discussed elsewhere in detail and will not be considered here. It may, however. be pointed out that the elaborate instrumentation required by the methods mentioned above, with the exception of the resistivity method (which is undesirable from other standpoints) encourages the development of methods of saturation determination which, while meeting the requirements listed, are simple to operate and maintain. It is the purpose of this paper to describe the instrumentation and evaluation of a technique for the determination of fluid saturation which combines relative simplicity with an accuracy and applicability comparable with methods now in practice. DESCRIPTION OF THE METHOD If the magnetic susceptibility of one of the fluid phases contained within a porous material is sufficiently greater than that of the remaining phases, the fluid content of the material with respect to that phase may be determined by an induction measurement. This may be accomplished by measuring the induced voltage in the secondary of a transformer which contains the porous sample and its interstitial fluids as a portion of the magnetic flux path. Since the fluids used in multiphase flow studies involving petroleum reservoir samples possess uniformly low magnetic susceptibilities, the use of a magnetic tracer in one of the fluid phases is required. In view of the relatively high paramagnetic susceptibility of salts of the transition elements, together with their high water solubility. these compounds become logical choices as tracer materials. Cobaltous chloride, having a specific magnetic susceptibility of 17.5 x 106 cgs electromagnetic units, was used as the tracer material throughout this work, in a concentration of approximately 20 per cent by weight in the aqueous phase. MAGNETIC SUSCEPTIBILITY APPARATUS Basically, the magnetic susceptibility apparatus consists of a transformer serving as the detecting head, a

Jan 1, 1955

By A. M. Gavdin, F. W. Bowdish

Mineral dressing is an industrial art concerned with the treatment and separation of solids suspended in fluids. Knowledge and evaluation of the area of solid-fluid interface is important in all cases except those involving only large pieces of solid. In fact, many problems relating to comminution, to flotation, to thickening and classification, could be dealt with more rationally if the interfacial area were known. A number of methods have been proposed for the measurement of the surface of certain finely divided solids. Among them are methods using rate of dissolution of the solid,? its magnetic remanence,³ the turbidity of its suspension," and the character of the size distribution of the material.9 The first two are limited to one mineralogical species per sample; the third has certain optical limitations, especially for mineral mixtures, and the fourth is based on an extrapolation of uncertain validity. The need of a better and more general method of surface determination has long been felt, therefore. The method of P. H. Emmett,4 based upon the low-temperature adsorption of vapors, appears to fulfill this need. This method consists in determining the amount of nitrogen that is adsorbed by a given sample of solid at the temperature of boiling nitrogen. The more surface there is on the solid—both internal and external—the more nitrogen is abstracted. In actual operation, the method is somewhat less simple than has been stated so far, in that the nitrogen is adsorbed in an incomplete layer, the completeness and thickness of the layer being related to the pressure of the nitrogen in contact with the sample.2 This circumstance makes it necessary to determine the nitrogen adsorption for three or more values of the nitrogen pressure. Apparatus In the Richards Mineral Dressing Laboratories an Emmett apparatus has been built and tested (Figs. I and 2). A mechanical vacuum pump B and a mercury diffusion pump A work in series to give a high vacuum. The sample, placed in bulb D, can be evacuated by this pump train by suitable operation of the stopcocks in the glass tubing that connects the various parts of the apparatus. C is a McLeod gauge, used to ascertain the order of magnitude of the vacuum obtained, and not for accurate pressure measurements. Pressure measurements are made in the mercury manometer F and gas-volume measurements in the gas burette E. Gases are stored in flasks L (nitrogen) and K (helium), arranged so that definite quantities of these gases can be introduced into

Jan 1, 1947

By M. F. Goudge, R. V. Tomkins

Sodium sulfate is an important chemical raw material that is being used in ever increasing quantities in modem industry. It comes on the market mainly in three forms: (1) Salt cake (Na2SO4), a relatively crude form of the anhydrous salt containing up to 3 pct impurities, and comprising about three-quarters of the North American production; (2) anhydrous sodium sulfate (Na2SO4), a refined form containing less than 0.3 pct impurities; (3) Glauber's salt, the decahydrate (Na2SO4.10H2O) containing 55.9 pct water of crystallization. Competing with salt cake from natural sources is byproduct salt cake from a number of industrial operations. For instance there is Mannheim cake resulting from the manufacture of hydrochloric acid by the reaction of salt (NaCl) and sulfuric acid in Mannheim furnaces; rayon cake, a high-quality product, resulting from the process of making rayon by the viscose process; chrome cake from the processing of sodium chromate to dichromate; phenol cake from the manufacture of phenol; also byproduct sodium sulfate resulting from the conversion of lithium sulfate to lithium carbonate; from the processing of sodium tetraborate to boric acid; from converting sodium formate to formic acid; and in the manufacture of cellophane. Sodium sulfate is also obtained as a byproduct in the manufacture of isosebasic acid. In addition strong competition has resulted from imports of byproduct salt cake from the chemical industries of a number of highly industrialized European countries. However in recent years due to technological changes the output of byproduct salt cake is rapidly diminishing and the natural deposits are becoming the most important source of sodium sulfate used in North America. For instance, the production of hydrochloric acid in Mannheim plants has become obsolete and thus the greatest single source of byproduct salt cake will disappear. Also viscose rayon is meeting strong competition from nylon and other synthetic fibers and production of byproduct salt cake from this source may do little more than remain at the present level. These factors together with increasing demand for sodium sulfate point to increased production from natural sources. In 1958, 36 pct of the total United States production was derived from natural sources and in addition 97,000 short tons was imported so that over 40 pct of the total consumption was supplied by natural sources whereas in 1953 the proportion was only 24 pct. The rapid growth in production is shown in Table 1. Principal Sodium Sulfate Minerals There are many minerals in which sodium sulfate is a constituent but those of commercial importance at the present time, and consisting wholly of sodium sulfate in either the hydrous or anhydrous states, are mirabilite and thenardite. Minerals of potential importance but consisting in part of compounds other than sodium sulfate are glauberite in which sodium sulfate is combined with calcium sulfate, and blödite in which sodium sulfate is combined with magnesium sulfate. Mirabilite (Na2SO4.10H2O) the decahydrate, consists of 24.8 pct SO3, 19.3 pct Na2O, and 55.9 pct H20. It is a colorless to opaque, soft, water-soluble mineral with a slightly bitter taste. It has a hardness of less than 2 and a specific gravity of 1.48. It forms long needle-

Jan 1, 1960

By Lane Mitchell

A ceramic product or processed material is a solid composed of materials which have been subjected to heat above 468.3°C (875°F). The raw materials, which are blended together (or in some cases used singly), are selected and utilized for various reasons such as ease of fabrication, aid to processing, to yield desired properties after processing, lack or controllable degree of toxicity or hazard, availability, cost, and perhaps other considerations. Almost all solid inorganic, some organic, and some liquid and gaseous materials have the potential to be used individually in some ceramic product. There are several fundamental functions to be fulfilled in every ceramic product and a number of secondary functions are desirable in specified products. These functions are generally met by the most widely occurring minerals and rocks of the earth and their debris. This fact characterizes ceramics as a field utilizing the raw materials most available to man. Of course, specified products utilize synthetics, organics, and rare inorganics to produce desired results. Any solid nonmetallic product processed by subjection to temperature above a red heat may be called a ceramic product. Widely used construction materials and units, domestic utensils and units, industrial parts to facilitate manufacture, technical components, and aesthetic creations are very often of a ceramic nature because of their durability, inertness, hardness, ease of fabrication, cost, and availability of the ingredients. Often, organics or metals cannot meet desired specifications for some of these products. The rocks and minerals and mineral debris of the earth are largely siliceous. Oxygen and silicon comprise roughly 75% of the earth's crust with aluminum, iron, calcium, and the alkalies following in abundance. Silica (SiO2) and silicates can be melted to form glasses. Alumina (A1203), present in a mineral compound, gives greater durability, hardness, and strength, but lessens the glass-forming property. Iron, calcium, and the other alkalies flux silica and reduce melting points. Thus sand, which is generally almost pure SiO2, and clay, which is generally hydrated alumina silicate, are the most widely used of all ceramic raw materials-principally because of the glass-forming propensities of silicates. In ceramic formulations, clay is generally a refractory filler or skeletal material, having in the raw state a plasticity derived from its colloidal grain size and its water-loving nature. On the other hand, silica sand is a glass former or nonplastic filler. Clay and silica sand in pure forms are quite refractory, i.e., not easily melted. Clay, although siliceous, is less of a glass former than pure silica and is more refractory. Natural contaminants, such as iron oxide or limestone, adulterate many clays and some sands. These contaminants act as fluxes and reduce the fusion points of the mineral or blends. Glass is made from silica sand by fluxing the sand with strong bases, usually soda ash and limestone. Red building bricks are hard and durable because the sand and clay have been partially fused with help of natural iron oxide serving as a flux. The iron oxide performs a dual function, serving as a pigment as well as a flux. In a blend of clay and sand and iron oxide, the sand is more susceptible to fusion than is the clay. Although silica sand and clay are the most widely used raw materials in most ceramic products, many other minerals, and some nonminerals are utilized in products where these materials can produce or aid in achieving desired results. Limestone and dolomite, feldspars, pigmentary minerals, refractory oxides or carbides, and special property producers can

Jan 1, 1983

By AIME

J. B. Haffner, or "Barney" as he is known to his wide circle of friends, was born at Landskrona, Sweden, on Christmas Day, 1886. He attended grade and preparatory schools there and then went to the Royal Technical Institute at Stockholm from which he graduated as a mining engineer in 1910. During these school years he gained practical experience in his summer vacations by working in various mines in Sweden and other European countries. Upon graduation he set forth for the land of opportunity, the United States. Upon arrival in this country he found people everywhere talking about the fabulous gold fields in Alaska and thereupon set sail for Nome, to take part in placer gold mining operations. Returning to the States, Barney worked in Illinois coal mines for a time and then carried on some construction work in Oklahoma. In 1913 he accepted employment with the Ray Consolidated Copper Co. in Arizona and soon found himself in positions of responsibility in the operating and

Jan 1, 1948

By Walter Knox, J. D. Doherty

IN 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. SUMMARY OF RESULTS Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3). 2. The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 1 1.6 per cent to 19.2 per cent. There was a noticeable segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may he a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance I. The removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. With intermittent operation the burning rate was almost always less than the feeding rate. The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. I3). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). GUIDING PRINCIPLES In planning the investigations, the following principles were adopted: Selection of Healing Equipment.-Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By Carlos E. Roggero

The influence of high temperatures on the zinc roasting practice has been investigated by full-scale tests in fluid bed reactors operating at temperatures from 950° to 1150°C. It was definitely shown that, throughout the range, an increase in tem perature resulted in a 2 to 3 pct increase in zinc solubility because of decreased content of zinc fer-rite and lowered sulfide sulfur. The former is attributed to thermal decomposition of ZnFe,O,, and the latter to increased oxidation rates, ad longer retention times. Data on the gveatly increased volatilization of lead, cadmium, and silver above 1000°C, are presented. A considerable fraction of the iron present in the feed was also transferred at high temperatures from the coarse roaster discharge to the flue dusts. AS part of its metallurgical complex1-3 situated in a 12,000 it Andean valley at La Oroya, Peru, Cerro de Pasco Corp. (a wholly owned subsidiary of Cerro carp.) operates a 150 short ton per day electrolytic zinc refinery. Electrolysis is carried out at a cathode current density of 65 amp per sq ft with an electrolyte content of 55 g per liter of Zn and 150 g per liter of su lf uric acid. Due to the high iron content of the marmatitic concentrate used, a large fraction—about 15 pct—of the zinc reports in the leach residues. To minimize such losses, efforts have been exerted toward improving calcine solubility. One method, as noted in the literatre,, is to retard zinc ferrite formation by decreasing the roasting temperature. Unfortunately, such a procedure tends either to reduce the roaster throughput or increase the sulfide sulfur in the calcine. Consequently, this approach was discarded in favor of experimental work in the opposite direction, i.e., high temperature roasting. Full- scale tests were promising and resulted in the granting of a patent to Cerro de Pasco carp.' After a brief account of plant equipment and operating procedure, this paper describes the tests made and attempts to assess the results obtained. GENERAL PLANT LAYOUT AND OPERATION The Roasting Plant, see Fig. 1, comprises an agglomerating plant feeding three fluid bed roasters with a combined capacity of 10,000 tons per month. The Peruvian patent rights on this process were purchased from the New Jersey Zinc Co. The concentrate, assaying: is pelletized to a -3 +14 mesh product and fed to the fluid bed roasters. The roaster exhaust gases pass through a waste heat boiler, cyclones, a fan, and an electrostatic precipitator. Approximately half of the dust collected in the cyclones returns to the pellet-izing plant as one of the binding ingredients, the remainder joins the cooled bed discharge ('overflow') and is conveyed to the grinding plant. The -35 mesh product obtained, together with the dust collected in the electrostatic precipitator constitute the feed to the leaching plant. Batch leaches are made in vessels with mechanical and air agitation, the residues are separated and washed in Burt Filters, and pumped to storage ponds. THE FLUID BED ROASTERS Two reactors are as shown in Fig. 2, and the third,' of about the same configuration, is approximately 40 pct smaller. The total grate and freeboard (just below the gas outlet) areas measure 170 and 426 sq ft respectively. The feed, continuously weighed and controlled by Merrick Weighto-meters fitted with variable speed motors, enters the reactors at the top of the expanded bed level. The coarse calcine overflows through the opposite end by

Jan 1, 1963

By D. G. Oss, S. E. Erickson

An automatic control method for the ferrosilicon heavy media process maintains media density within 0.01 specific gravity points. Continued demands for higher grade, competitive products from the Mesabi Range have resulted in experimental work such as that detailed for one concentrator. Various methods, step by step procedures and instruments used at an iron ore beneficiation plant in the development of an automatic control system are described. Work continues and it is hoped that further applications of control instrumentation can be made in the next operating season. The need for instrumentation and automatic control of the various parameters in the heavy media process of iron ore beneficiation has been apparent for some time. Continued demands for higher grade, competitive products from the Mesabi Range have made it necessary to increase the efficiency of the process in every possible way. In a typical heavy media flow scheme for iron ore beneficiation (Fig. 1) a sized, prepared feed (generally about —1% in. to +% in.) is fed to a heavy media separatory vessel, along with a ferrosilicon slurry. A separation of the feed is made on the basis of specific gravity. Low density particles overflow a tailings discharge weir, while high density ore particles sink to the bottom of the high density pool and are moved away to the concentrate discharge chute. Both products are passed over drainage screens and then are cleaned thoroughly of attached ferrosilicon on wash screens. Float material is generally stockpiled, while the sink product is shipped as a final concentrate. Undersize from the drain screens is returned directly to the circulating media sump. Wash screen undersize is cleaned of contaminating ore particles and slimes by passing through magnetic separators. Provision is also made for splitting a portion of the tailings drain undersize into the cleaning circuit if necessary for control of depth of tailings overflow, or for additional cleaning as required. Cleaned ferrosilicon is stored in a densifier and returned to the Circulating media sump as make-up material. Dilution water is also added to this sump to maintain a desired specific gravity of the circulating media. As in any process, operational intelligence is secured only by keeping records of the process variables. Generally apeaking, plant operators have neither the inclination nor the time to keep complete and detailed records of these variables over the course of their shift. Before instrumentation was added to aid the operator, specific gravity was measured by weighing a given volume of pulp at intervals of from 30 to 60 min. Scale readings were made at the beginning and end of each shift. No records were kept of operating conditions, such as rpm of the separatory ves-sel, media level in the machine, tons per hour of the products, and so forth. These items were recorded only when spot checks were made by the metallurgical staff. CONTlNlJOUS DENSITY RECORDING The first process instrument used, other than the usual ammeter on the drive motor of the separatory vessel, was a nuclear density gauge and its associated circular chart recorder. These instruments were used to indicate and record specific gravity of the circulating media. This was a tremendous aid to the operator in that tie was able to observe and correct the specific gravity at any time. There was also added incentive to make frequent corrections because of the permanent record made by the recorder of the densities. The addition of the nuclear density gauge was influential in securing optimum quality and recovery of the heavy media product. Manual control was improved, and it became possible for a good operator to main control within f.05 specific gravity units. This compares with an unknown quantity, estimated at f0.15 gravity units, when manual measurement and control was used. An example of the improvement in manual control over the course of one season's operations is shown in Fig. 2. Chart A is typical of the records made shortly after the gauge was installed. Needless to say, it was difficult for operators and foremen alike

Jan 1, 1962

By R. N. Hoffman

A new technique for determining capillary pressure curves has been developed and tested. The technique differs from previously reported centrifuge techniques in that the centrifuge is slowly accelerated from zero to the maximum desired speed rather than being held constant at particular, progressively higher speeds. An important advantage of this technique over other methods of determining capillary pressure curves is the short time required to obtain the desired amount of data over the chosen pressure range. For example, to obtain 30 data points between 1.2 and 104 psig with a 1.55-in. long, 3/4-in. diameter core using a brine-air system, 6.6 hours were required with this technique. An equally important development of this paper is an analytic method for the conversion of the data from the centrifuge experiment to capillary pressure curve data. Previously there has been only an approximate conversion available. Although the capillary pressure curves determined by this technique appear to be as accurate as those determined by other techniques, the accuracy could be improved if certain variables, not treated in this experiment, were investigated. Among these are the dynamic distortion of the centrifuge equipment and imperfect initial saturation of the cores. INTRODUCTION Pirson 1 defines capillary pressure in a porous medium as "the differential pressure that exists between two fluid phases at their interfaces when they are distributed under static equilibrium within a porous material". Capillary pressure in rocks is known to be a function of fluid saturation, among other things, and a capillary pressure curve is defined for the purposes of this paper as a plot of the capillary pressure-wetting phase saturation relationship for a particular rock sample. Several methods are used for determining capillary pressure curves for small rock cores. Prominent among these are the semi-permeable barrier, mercury injection, and, to a lesser extent, centrifuge methods. The semi-permeable barrier method is currently the most popular. It features simplicity in both execution and the mathematical conversion of the experimental data into a capillary pressure curve. The main disadvantages of the semi-permeable barrier method are the time required — as long as two months — to obtain several points for the curve, and a fairly low maximum pressure before breakthrough of the non-wetting phase into the barrier occurs, for example, about 32 psig for a brine-air system. It is for these reasons that other methods such as the centrifuge method have been introduced. High accelerations and the absence of a barrier result in quicker attainment of saturation equilibrium at a given pressure. However, the centrifuge method involves much more expensive equipment and more difficult procedures and calculations than does the barrier method. The purpose of this investigation has been to improve the equipment and procedures of the centrifuge method and to develop an analytic method for the conversion of the experimental data into a capillary pressure curve. Hassler and Brunner did the original work in the determination of capillary pressure using a centrifuge. In their work the centrifuge speed was increased in a step-wise manner, each speed being held constant until saturation equilibrium was reached in each core. Saturation equilibrium was indicated when the volume of liquid collected in the graduated pipette of the core holder remained constant. According to Hassler and Brunner, equilibrium was reached in "a few minutes to one-half hour or more". In the centrifuge method, as opposed to the barrier method, the fluid saturation of the core is not a constant throughout the length of the core, but varies with the radius of centrifugation. Also, the capillary pressure cannot be read directly but must be calculated from a knowledge of the centrifuge speed and other parameters. For these calculations, Hassler and Brunner derived the following equations:

By A. D. Schwope, L. R. Jackson, A. M. Hall

IN the course of an extensive investigation of the comparative properties of several types of copper, data were obtained on the cold working and subsequent recovery and recrystallization of the copper. In this paper, relations between the degree of cold work and the course of recrystallization are developed. In particular, it is shown that the course of recrystallization over long periods of time and at low temperatures can be predicted with reasonable accuracy from short-time high-temperature recrystallization data. MATERIALS USED IN THE INVESTIGATION Three types of copper were used in this investigation; these were tough pitch, OFHC, and OFHC copper with 15 oz per ton of silver added identified herein as Lots C, D, and F, respectively. The material was supplied by the American Metal Co. Ltd., and processed by the Rome Cable Co. The analyses of the three types of copper are given in Table 1. Originally, it started as wire bars 4 X 4 X 54 in. These bars were heated to 871°C in air and hot rolled to 3/8 in. rod. This rod was cold drawn to 0.204 in. rod (70 pct reduction) in three passes and annealed at 427°C for 4 hrs. A portion of the 3/8 in. rod was saved for more detailed cold-drawing experiments. Starting with the annealed 0.204 in. rod, hard-drawn wires were produced by cold drawing to 0.081 in. wire in 7 passes (84.4 pct reduction in area). Half-hard wires were made by cold drawing the 0.204 in. rod to 0.102 in. wire, (75 pct reduction) in 6 passes and annealing at 427°C for 4 hrs. This annealed wire was then drawn to 0.081 in. wire, (37.1 pct reduction) in 2 passes. Square rod was made by hot rolling wire bars to 9/16 in, rod in 8 passes. This rod was then cold drawn to 0.445 in.-diam rod and annealed for 3 1/2 hrs at 538°C. It was then cold drawn to 0.325 in. rod and again annealed at 538°C for 3 1/2 hrs. Hard square rods were then made by cold rolling this material to 0.257 X 0.257 in. rod, a reduction in area of 20.5 pct. Half-hard square rods were made by cold rolling to 0.268 X 0.268 in. square, annealing for 332 hrs at 538°C and cold rolling to 0.257 X 0.257 in., a reduction of 8.5 pct. Soft wire or rod was made from all types of copper by annealing the hard-drawn material at 343°C for 3 hrs in steam. The grain size of the annealed 0.081 in. wire varied slightly among the three lots: from 0.015-0.025 mm in the silver-bearing OFHC to 0.035-0.045 mm in the OFHC copper. The annealed 0.257 in. wires were more uniform in grain size, averaging about 0.035-0.045 mm. Representative structures are shown in Fig I. EFFECT OF COLD DRAWING AND TENSILE STRAIN ON STRENGTH OF COPPER Conventional tensile tests were performed on the three types of copper in the various degrees of hardness described above. Results of these tests are tabulated in Table 2. The results in Table 2 are

Jan 1, 1947

By R. P. Aikman, F. G. Miller, J. M. Podgursky

As part of a larger study of the mechanism of froth flotation of coal, the rates at which coal particles of various size and specific gravity react to froth flotation were investigated. Results of this study show that in flotation: I) recovery rate increases, but selectivity decreases with a decrease in particle size down to 100 mesh, and 2) recovery rate is constant for all sizes between 100M and 325M. n response to the growing demand for low-sulfur coking coal for iron making, the coal industry is continually striving to perfect methods for cleaning coal to acceptable ash and sulfur levels while maintaining maximum product yield. By present standards the industry has adequate processes for cleaning coarse coal, i.e., + 28 mesh, at almost any desired specific gravity. However, in the case of fine coal, i.e., —28 mesh, neither of the two existing processes - froth flotation or hydrocycloning — in its present state of development yields products that are comparable in ash and/or sulfur content to products normally obtained from coarse coal processes. The work outlined in this paper is part of a larger study directed toward maximum exploitation of froth flotation for fine coal processing. The concepts and data presented are now serving as a basis for designing fine-coal circuits in which improved efficiency is obtained by optimum use of froth flotation with other fine-coal processing methods. The paper includes: 1) A discussion of the value of a detailed wash-ability study as a method of assessing the problems associated with fine coal processing, 2) A general discussion of hydrocyclone principles, included to serve as a basis for understanding the mechanism of coal flotation, and 3) A detailed discussion of the mechanism of coal flotation, as well as the research leading to the optimum use of froth flotation in combination with other fine-coal cleaning methods to provide efficient fine-coal processing. Our study of the rates at which coal particles of various size and specific gravity react to flotation shows that in flotation: 1) recovery rate increases but selectivity decreases with a decrease in particle size down to 100 mesh, 2) recovery rate is constant for all sizes between 100 mesh and 325 mesh, and 3) the flotation process effectively rejects only those extremely fine particles which do not contain surface carbon. (Because of this feature, froth flotation is an excellent method for rejecting clays - the only extreme fines in - 325-mesh coal that are always carbon free.) Washability studies of flotation products are used to assess flotation efficiency. These studies show that: 1) the increase in percent sulfur in flotation products above the theoretical sulfur content as defined by the washability study is due almost entirely to flotation of fine high-specific-gravity particles that are part coal and part pyrite, and 2) in a given size range particle floatability decreases with an increase in particle specific gravity. Error curves are explained and are used to compare the mechanisms of coal flotation and hydrocycloning. These comparisons show that hydrocyclone performance is affected primarily by particle mass, i.e., particle specific gravity and size, whereas coal flotation performance is dependent on both the particle mass and the coal surface available for bubble attachment. Since the error curve is a basic tool for rating the efficiency of any coal processing system, it will be useful to quickly review the principles of error curve construction. RATING COAL-PROCESSING EFFICIENCY BY THE ERROR CURVE The organic component of coal is of lower specific gravity than its impurities, and the most effective principle for coal concentration is therefore separation on the basis of specific gravity. However, since there is no sharp dividing line between pure coal and pure ash components, specific gravity must be closely controlled if the product is to have acceptable quality at maximum yields. In turn, the basis for close control in any coal processing system is the reference standard provided by precise laboratory washability studies. In these studies, coal is carefully separated into a series of progressively higher specific gravity fractions to establish a relationship

Jan 1, 1968

By G. C. Rauch, T. H. Courtney, J. Wulff

The superconducting behavior of Nb-Ti alloys containing 40 and higher wt pct of Nb and variable oxygen content was studied as a function of thermomechanical processing. Critical current density (Jc) us applied transverse magnetic field (H) data were obtained for 0.010 in. diam wires at 4.2° Kin steady fields up to 120 kOe. The precipitate responsible for increase in Jc in each of the alloys studied was related to niobium and oxygen content. In alloys containing 40 to 60 wt pct Nb with less than about 1600 ppm of oxygen, w precipitation in the range 350° to 450°C appears to be responsible for the maximum value of Jc observed. In alloys of higher oxygen content (-2500 ppm), the oxygen-enriched a phase which precipitates in the temperature range 450° to 550°C is a more effective fluxoid pinner. Maximum Jc in low oxygen (350 ppm) 80 wt pct Nb alloys was achieved by 600°C aging heat treatments. Measurements of resistive critical field also reflect the changes in composition accompanying precipitation in these alloys. It is well known that the superconducting critical current density, Jc, of solid solution superconducting alloys can be increased by precipitation heat treatments.1-4 The precipitate, to serve as an effective superconzlucting fluxoid pinner and increase Jc, must be of proper size and spacing.' Its electronic properties must also be different from those of the matrix.6 As in age-hardenable systems, optimum temperature and time of aging are dictated by the composition and history of the particular solid-solution alloy under consideration. The alloy diagram of Ti-Nb7-9 shown in Fig. 1 is typical of ß-stabilized Ti alloys. Precipitation to achieve high Jc in Ti-Nb and Ti-Ta alloys is usually carried out in what is believed to be a two-phase a + ß region.1,2,4,10 Previous work on Ti-Nb4,11 and on other ß-stabilized systems such as Ti-V, Ti-Mo,12-14 has shown, however, that the first precipitate to appear is not necessarily (Y. Under specific conditions the meta-stable w phase is precipitated instead. A further complication arises in such alloys from the strong influence of contained oxygen on the phase stability and on the kinetics of precipitation.15,16 The superconducting critical current density of Nb-Ti alloy containing less than 36 wt pct Nb has been studied by Vetrano and Boom1 and Kramer and Rhodes.4 The most effective aging temperature was found to be about 425°C; fluxoid pinning was attributed to the precipita- tion of a by Vetrano and Boom and of w by Kramer and Rhodes. Although the latter workers used recrystal-lized material and the former cold-worked, studies carried out in our laboratory lead us to believe that the type of precipitate responsible for increased Jc is unaffected by prior cold-work.17 That other types of precipitates may also be effective, especially in higher oxygen-containing alloys, has been demonstrated by Reuter, et al.2 in this laboratory with the aid of electron microscopy. Reuter et al. found that at an aging temperature of 600°C, fee-TiO is precipitated, resulting in high values of Jc. Even higher values of Jc were observed after heat treatment at 500°C, but the precipitate could not be indexed as fee-TiO. Whether the precipitate was oxygen-rich w or a could not be clearly distinguished. The work nevertheless indicates that appreciable amounts of oxygen alter the nature of the phases precipitated at different temperatures, at least in alloys containing more than 36 wt pct Nb. Since such compositions are more readily worked into suitable wire than lesser niobium content alloys, it was decided to study the response to aging of the alloy compositions reported in the present paper with the hope of clarifying the effect of composition on the precipitation processes responsible for high values of Jc. I. EXPERIMENTAL Nb-Ti alloys containing 40, 50, 60, and 80 wt pct Nb were prepared by are-melting 35 g ingots of iodide crystal bar titanium and electron-beam melted niobium.

Jan 1, 1969

By L. W. Holm, G. G. Bernard

Laboratory experiments were conducted to determine the effect of foam on gas flow in porous media. Previous studies have indicated that foam may be applicable as a restrictive agent in influencing underground gas flow. Foam was found to be exceedingly effective in reducing the permeability of porous media to gas. Consolidated and unconsolidated sands with specific permeabilities of 100 to 146,000 md had, in the presence of foam, gas permeabilities that were less than 1 per cent of the specific permeability; in many cases the gas permeability was practically zero. Foam reduced the gas permeability of loose sand to a much greater degree than that of a tight sand. For example, the permeability of a 125,000-md sand was reduced to 3 md while the permeability of a 4,000-md sand was reduced to 7 md. This effect should cause, to some degree, selective plugging of high permeability channels in various oil displacement processes. The presence of oil in a porous medium decreased the effectiveness of foam in reducing gas permeability; apparently oil acts as a foam depressant. However, it was found that certain foaming agents were very effective in reducing permeability even. in the presence of oil. Also, continuous injection of other foaming agents increased their effectiveness, when oil was present. The effect of foam on permeability of porous media to gas was studied as a function of foaming agent concentration and injection rate, absolute permeability, total pressure, pressure gadient, length of porous system, brine concentration and time. INTRODUCTION The use of surface active agents in flood water to increase the recovery of oil has been studied in the laboratory and in the field for decades, with rather limited success. In recent years a new approach to the problem was proposed. Instead of using an aqueous solution of surfactant as an oil recovery agent, Bond and Holbrook2 proposed that the oil recovery agent be a mixture of surfactant solution and gas. In their method, a water-soluble surface active agent with foam-producing characteristics is injected into an underground formation as an aqueous slug. This slug is followed by gas to produce a foam within the rock. Foams are defined as "agglomerations of gas bubbles separated from each other by thin liquid films'! A foam is fundamentally an unstable system. The foam process for oil recovery has since been studied by other investigators. Fried 1 has shown that foam can displace from porous structures oil that normally is unrecoverable by conventional water or gas drives. This superior oil displacing action is believed to be the result of several factors: (1) foam introduces into the reservoir many resilient interfaces of various sizes and curvatures, which increase the probability that a proper combination of forces for oil displacement will be created; (2) foam has appreciable viscosity which improves mobility ratio and contact efficiency; (3) foam accentuates the trapped gas effect because high gas saturations are possible without producing high gas/oil ratios. Deming4 studied the effect of various foam properties on the displacement of liquid. He found that (1) high foaming ability favors high displacement efficiency; (2) high foam stability is not necessary for high displacement efficiency; (3) displacement efficiency decreases with increase in plasticity of foam and (4) displacement efficiency is unaffected by surface tension of foaming agent solution. One of the important aspects of this oil recovery process is the effect of foam on gas permeability. The simultaneous flow of gas and liquid in porous media has been studied by numerous investigators and a large amount of literature exists on the subject. In this previous work, gas and liquid have generally been considered as essentially independent phases, whose flow characteristics are related through the saturation parameter. Foam, however, is a material with properties that are considerably different from those of its components; for example, the viscosity of a foam is greater than either of its components. Gas flow in a porous medium in the presence of foam should be considerably different

Jan 1, 1965

By D. Turnbull, J. H. Hollomon

THERE is a large body of evidence'" indicating that solidification during the liquid-solid transition is usually induced by heterogeneities present in the liquid. By dispersing liquid metals into small droplets, the impurities responsible for catalyzing solidification are isolated within a small number of these droplets. The effect of the foreign body therefore is restricted to a single drop by this technique. Thus upon cooling below the melting temperature, solidification is initiated by homogeneous nucleation in the majority of the droplets that do not contain impurities. In the case of solidification of liquid metals, the activation energy for nucleation is so great that its rate changes by orders of magnitude for a change in temperature of only several degrees centigrade.' Effectively homogeneous nucleation occurs at a critical temperature upon continuous cooling. Thus by microscopic observation of single particles during cooling, a temperature at which the rate of homogeneous nucleation becomes sensible can be determined.3 since at the temperatures at which nucleation occurs in the absence of impurities the rate of crystal growth is extremely rapid, the temperature at which the entire particle solidifies is very nearly the temperature at which the nucleation of the solidification occurs. Thus for liquids that freeze at high temperatures the onset of nucleation can be established by simply observing the temperature at which the marked heat evolution and increase in brightness of the particle occur. For liquids that freeze at lower temperatures the onset of nucleation can be determined by a rumpling and change in shape of the particle resulting from its solidification. The microscopic technique for observing the solidification of small particles has already been described." In earlier papers the nucleation of solidification of pure metals 5,6 and of alloy systems7 showing complete liquid and solid solubility have been described. In the present paper, the observations are extended to a simple eutectic system (Pb-Sn) where the possibility of the formation of two solid phases exists. Metals for the investigation were obtained from the American Smelting and Refining Co. in the form of pure lead and pure tin, 99.8 and 99.9 pct purity, respectively. An ingot of each of the pure metals was made into shot by heating the metals at a temperature about 50 °C in excess of the melting point and pouring the liquid slowly into a container of water at 15°C. Samples of the shotted pure metals were weighed out to make alloys containing 5, 10, 15, 20, 25, 30, 40, 50, 60, 70, 80, and 90 atomic pct Pb. Samples of each alloy were then melted in separate beakers. Each melt was poured through a pyrex funnel into a cylindrical mold (% in. ID). The casting solidified in 10 to 20 sec. The inside of the mold as well as the funnel through which the metal was poured were coated with graphite to eliminate adherence of the metal. Analyses were performed on some of the compositions and are given in Table I. The compositions also were checked for these samples and for those that were not analyzed by determining the spread between the liquidus and the solidus upon melting the small metal particles. These measurements agreed as well with the nominal compositions as the analyses listed above. Results The results of the supercooling experiments for the several alloys are summarized in Table II and plotted on the constitution diagram in Fig. 1. Data for the pure lead and pure tin were taken from earlier investigations. The values for the maximum supercooling of the several alloys are the average of several determinations on a number of drops of each alloy. The maximum value in any determination was within about 2 pct of the average. For the alloys containing from 20 to 60 atomic pct Sn, inclusive, two marked changes of the surface structure were observed upon cooling. At the higher temperature, after the first appearance of the solid phase it continued to grow slowly at a constant temperature and then stopped. At the lower temperature the alteration of surface structure was abrupt. For the alloys containing from 70 to 95 atomic pct Sn, inclusive, an abrupt change in surface structure was observed at a single critical temperature.

Jan 1, 1952

By D. W. Mitchell

INE operators have a choice of several classi- fications of mechanical loaders. Within each classification there are many types and makes available. Table I lists loaders on which manufacturing data as to operating characteristics are available. This paper discusses the conditions met in a mine as they affect these characteristics. It is assumed that management will provide satisfactory engineering, supervision, power, maintenance, loader service within a concentration of workings, and a balanced working cycle served by balanced production equipment. These are factors which affect the optimum operational efficiency of a loader. The conditions which determine loader choice are: Height of Vein—The main limitation to the use of a loading machine is the height to which the vein is mined; i.e. a loader cannot be higher than the place in which it is to work unless rock is taken. Since there are several low vein loaders being developed and successfully applied, this does not appear to be a requisite of an efficient mining operation. The maximum useable height of a loader should be equal to the working seam thickness less a working clearance for travel and operation. A—Working seam thickness = B—Artificial roof support thickness = C—Safe headroom below support = (generally about 6 in.) D—Height of roadway = E—Total of B + C f D =_______________________ A—E = maximum loader height F—Distance from top of roadway to bottom of roof support = G—-Height of loader's coal or ore line (see Table I) = H—Difference between F and G = Size of largest broken particle + a safety factor of 2 to 3 in. H is a loadability factor and is important because the clearance over the top of the conveyor chain to the roof or roof support must be greater than the largest broken particle or else the particle and/or the conveyor chain may be broken. From this standpoint it might be desirable to use a lower height machine even though it may have a smaller capacity, though this is warranted only when increased lump realization offsets lower man-day and machine pro- duction rates. Ivan Given has stated, "Loading should not be handicapped by securing lump only to grind it in the breaker." Width of Working Place—The width of a working place is the greatest width a place may be safely driven. The working place includes not only the face but the roads the loader must tram when mucking out more than one face. The width is limited by the system of placing props with sufficient room between them for the machine runner (about 2 ft). Maximum width of place in which the loader will operate at maximum efficiency is determined by the type of mounting. With track-mounted loaders, maximum width of place is determined by maximum angular swing of the loading head and proximity of track to the face. The use of double track leads to added expense and operational complexities. Several mines that have used double-track systems have found that a substantial saving is made by the use of machines that load out wider places. Trackless loaders may work in rooms of any maximum width. Minimum width of place in which a loader will operate is determined by width of the loader plus a safe movement area for the operator. Often a barodynamic study of the mine will show that either an increase in room width and/or a change in the system of propping may be made by using roof bolting, full or part-width room timbers, removable aluminum I-beams at the face, etc. Increasing the width of a working place will, in general, increase loader operating efficiency by providing more material per fall and by decreasing the preparation and moving time per ton. A change in the system of propping that would increase the minimum width might permit the use of a higher capacity loader with safer working conditions. Proper face tirnbering is necessary to insure safety from roof falls and because the speed of preparation and loading generally increases since the men work with greater assurance and there is less chance of kicking out posts. Maximum Room Length—With the exception of the scraper and the duckbill, the limit to room

Jan 1, 1952

By N. K. Chen, R. Maddin

In the extension of molybdenum single crystals at room temperature, the slip planes were found to be of the type (1101; the slip direction <111>. Theories of plasticity of body-centered cubic metals have been examined, and an explanation based upon planes of highest atomic density seems plausible to explain the plastic behavior of molybdenum single crystals. IN body-centered cubic metals, slip has been reported to occur on several planes; these are of the type {110), {112), and (123). Andrade has correlated&apos; the operative slip planes in body-centered cubic metals with the testing temperature relative to the melting point. In this correlation, if T is the absolute temperature at which slip takes place and Tm the absolute melting point, then the acting slip planes in body-centered cubic metals may be arranged as shown in Table I. However, deviations from this correlation have been reported in iron and iron-silicon alloys2 and also in molybdenum deformed at a temperature around 2400°C." In the case of iron and other body-centered cubic metals or alloys in which all three slip planes have been reported to be active at any one temperature, the crystallographic mechanism of slip is not well understood. Numerous investigators in this field have assumed that the resolved shear stress is a deciding factor. Such considerations were given by Gough in his experiments with repeated torsion of iron single crystals4 and recently by Opinsky and Smoluchowski in their study of iron-silicon alloys," and will be dealt with later in this report. A third possibility is that slip lines in body-centered cubic metals may be formed by alternate slip on nonparallel (110) planes and not by slip on any plane of higher indices. This was advanced by Elam in the case of ß brass." Since (1101 planes are planes of highest atomic density in the body-centered cubic structure, this hypothesis would be in accordance with the plastic behavior of metals in other systems, namely, face-centered cubic and hexagonal close-packed. Experimental evidence in support of this hypothesis is lacking. Nevertheless the work of Barrett, Ansel, and Meh12 has definitely demonstrated that the slip resistance on {110} planes in iron is very much smaller compared with that on (112) and (123) planes. In the present investigation, molybdenum single crystals were carefully documented as to the operative slip planes and lattice reorientations after plastic extension at room temperature. In three crystals studied, (110) planes were found to be active invariably rather than the (112) planes, which were previously reported for molybdenum at this temperature&apos; and predicted by Andrade&apos;s theory.&apos; In two other cases (112) and (123) planes seemed to operate together with (110) planes as active slip planes. However, it is believed, after careful analysis of crystallite and lattice rotations, that slip on (112) and (123) planes may be spurious. Particular reference will be made to the formation of asterism, lattice rotation, and crystallite rotation in an attempt to show that slip apparently observed on {1121} and (123) planes is actually slip on nonparallel {110} planes. Materials and Treatment Sintered molybdenum rods ? in. in diam, obtained from the Fansteel Metallurgical Co., were reported to have a purity of 99.9 pct.* One specimen, Mo-13, ¼ in. in diam, was supplied by Westinghouse Electric Corp. Single crystals were prepared, using the technique devised by Chen, Maddin, and Pond." Mo-13 was ¼ in. in diam x 7 in. long with a reduced gage section of 0.200 in. in diam x 3 in. long. The center of

Jan 1, 1952

By James Boyd

Scientists and engineers must concern themselves not only with technical problems, but with the socio-economic difficulties of our scciety. The author states that raw materials are basic to the economic process and that mineral raw materials occur naturally in nearly limitless quantities. He feels that the economic pocess will provide sufficient raw materials for man&apos;s needs, and discusses in some detail the world economic environment. As our society grows in complexity, it becomes more urgently incumbent upon scientists and engineers to bring their experiences to bear on the solution, not only of technical problems, but also on socio-economic difficulties. It is to this field that I have directed a large part of my energies. RAW MATERIALS BASIC TO THE ECONOMIC PROCESS There are certain premises, frequently overlooked, which bear emphasis. As economics concerns the production, distribution, and consumption of goods, so our whole society is based on raw materials. Without the basic extractive industries of agriculture and mining, there would be no economic problems with which to deal. This principle has been expressed as "All productivity is based on three factors: 1) natural resources, whose form, place, and condition are changed by the expenditure of 2) human energy (both muscular and mental), with the aid of 3) tools.77* It seems strange that such an obvious statement needs to be made. It is forgotten by all of us, however, at one time or another when we get involved in the complicated theories of economics dealing with the financial and fiscal policies of the various governments, in the financing of enterprises, in marketing, and in labor relations. Unless decisions in all of these fields are made with this, and the rest of the "Ten Pillars of Economic Wisdom," consciously in mind, the resultant policies are doomed to eventual failure, whether these are policies of individuals, companies, or governments. The economic process is basic to society. But economics and the social aspects of humanity are inevitably intertwined. If human needs are not provided for within the basic economic structure, conflicts arise to disrupt the most carefully laid social plans. Similarly, it is the failure of society to cope with basic economic prerequisites that leads to discord within the body politic and thus to eventual economic disaster. We who are engaged in the various aspects of the mineral industry, therefore, have a large part to play in society&apos;s future development. MINERAL RAW MATERIALS OCCUR NATURALLY IN NEARLY LIMITLESS QUANTITIES Throughout my career in and out of government, I have formed my decisions on two principles: 1) Fundamentally, all mineral raw materials exist within the earth&apos;s crust in quantities greatly exceeding man&apos;s needs; 2) Any problems of supply of these materials are primarily economic in nature. With respect to my first assumption, analyses by geochemists enable them to estimate the quantities in which each of the known elements exist in the earth&apos;s crust. One of the most cautious and famous suggests that the average copper content of the lithosphere to a depth of ten miles is about 55 ppm. If this is valid, then the lithosphere contains about 1.4 quadrillion (1.4 x 10 ") tons of copper metal — an unimaginable quantity. This is 8,500,000-fold that which has been consumed by man in his existence. To illustrate further, consider that the deepest copper mine in history went to about 9000 ft below the surface; the present copper mines of the world now average less than 1500 ft in depth. We can assume that in most continental land areas of the world it is technically feasible to mine to a depth of at least one mile. The land areas of the world to an average depth of one mile, then, contain 343 billion tons (343 x 10&apos;) of copper metal, or 2000 times that which has been extracted to date. I don&apos;t believe man will ever expend his energies to extract copper from rocks which contain only a few parts per million, but he knows that each element

Jan 1, 1968

By P. Bardzil, J. Gurland

An experimental study of the variation of transverse-rupture strength with composition Anexperimentaland grain studysize has shown that the strength reaches a maximum for values of the mean free path between carbide particles of 0.3 to 0.6 microns. The fracture oforiginates in and proceeds through the carbide grains mainly. Impact strength and hardness also were recorded. MOST of the physical properties of sintered carbides vary linearly with composition. The transverse-rupture strength, however, shows a unique behavior. As the amount of binder metal is varied from 6 to 25 pct by weight, the strength at first increases; then, between 15 and 20 pct Co, it reaches a maximum of nearly 400,000 psi, and finally decreases with further additions of binder metal. This behavior of the transverse-rupture strength has been reported, among others, by Englel and Sandford and Trent.&apos; The significance of these observations has not been discussed in the literature. That it may be of more than specific importance is indicated by the very similar variation of strength with composition encountered in other systems sintered in the presence of a liquid phase, such as Tic-Ni3 and Fe-Cu.&apos; Experimental Details All compacts were prepared and sintered according to normal industrial practice. The average diameter of WC grains and the mean free path between grains were measured on metallographically prepared samples by a method of linear and planar analysis sing the relations where d is the average diameter of dispersed grains; Nl is the number of noncontiguous grains intersected on a metallographic plane by a line of unit length; N, is the number of noncontiguous grains per unit area; P is the mean free path between grains of dispersed phase; and f is the volume fraction of dispersed phase. Approximately 1000 grains were counted on each sample. For each composition d2 was plotted against P, the resulting straight lines serving as a check on the measurements. The distribution curves of the WC powders of different average diameters were homologous, and no attempt was made to influence the grain size by blending powders, adjusting the sintering conditions, or otherwise altering the particle size distribution. Densities were measured by differential weighings in air and water. The degree of densification did not vary consistently with either composition or grain size. The density is influenced by slight amounts of impurities, specifically by 0.1 to 0.2 pct Fe which enters the powders during ball milling. As an illus- -tration of the experimental variations, a number of measured densities are listed in Table I. They are expressed in percentage of theoretical density, as calculated from the published X-ray densities of WC and Co.&apos; For the purpose of determining the transverse-rupture strength, rectangular test specimens (3/16x 3/8x3/4 in.) were broken by loading at the center of a 9/16 in. span. The average strength of five or more samples is reported for each composition and grain size. The compacts were ground on two parallel surfaces only. The load was applied at an average rate of 6,800 psi per sec. Since the elongation after fracture of the alloys is very small, it was assumed that the compacts deform elastically to failure and the fracture stress was calculated by the conventional beam formula. The data for one alloy are presented in Table II as an example of the results and scattering ranges encountered. The precision of the test, as measured by the average difference between duplicates, is of the order of 15,000 psi. The results are strictly comparable only to compacts prepared and tested in the manner described and of similar chemical composition and grain size characteristics. Unnotched Charpy specimens were used for impact testing. Each point represents the average of 3 to 20 samples, the larger number being used in an attempt to determine the influence of grain size. Considerable scatter was encountered, the range from lowest to highest value often amounting to 30 pct of the impact strength. The hardness is reported as a Ra reading, using a 60 kg load with diamond brale indenter. Compositions are given in weight percent.

Jan 1, 1956

By John Chipman, Minu N. Dastur

This paper presents equilibrium data on the reaction of water vapor with vanadium dissolved in liquid iron at 1600°C. The thermo-dynamic behavior of vanadium and oxygen when present together in the melt is discussed. A deoxidation diagram is presented which shows the concentrations and activities of vanadium and oxygen in equilibrium with V209 or FeV2O4. STUDIES of the chemical behavior of oxygen dissolved in pure liquid iron1-3 have served to determine with a fair degree of accuracy the thermody-namic properties of this binary solution. The practical problems of steelmaking, however, involve not the simple binary but ternary and more complex solutions. Only a beginning has been made toward understanding the behavior of such systems. The silicon-manganese-oxygen relationship was studied long ago by Korber and Oelsen4 and more recently by Hilty and Crafts." The carbon-oxygen reaction was investigated by Vacher and Hamilton6 and by Marshall and Chipman.7 A number of deoxidizing reactions have been studied empirica1lys&apos;10 with the object of determining the appropriate "deoxidation constants." The work of Chen and Chipman" afforded a clear-cut view of the effect of the alloy element, chromium, on the thermodynamic activity of oxygen in liquid ternary solutions. These investigators determined the oxygen content of experimental melts which had been brought into equilibrium with a controlled atmosphere of hydrogen and water vapor and were able to show that the presence of chromium decreases the activity coefficient of oxygen. They determined also the conditions under which the two deoxidation products, Cr2O3 and FeCr2O4, were formed and showed that the activity of residual oxygen is considerably less than its percentage. It was the object of this investigation to apply a similar method to the study of molten alloys of iron, vanadium, and oxygen. Vanadium was once considered a moderately potent deoxidizer, but this is now known to be erroneous, in the light of its behavior in steelmaking practice. Its reaction with oxygen retains a certain amount of practical interest in that a high percentage of one element places a limit on the amount of the other that can be retained. As a deoxidizer it will be shown that vanadium lies between chromium and silicon. Experimental Method The apparatus was that used by the authors3 in their study of the equilibrium in the reaction: H2(g) +O = H2O(g);K,= [1] PII., ao Crucibles of Norton alundum or of pure alumina were used. The latter were made in this laboratory and were of high strength and low porosity. Under conditions of use they imparted no significant amount of aluminum (less than 0.01 pct) to the bath. Temperature measurements were made with the optical equipment and calibration chart of Dastur and Gokcen.= The charge was made up of calculated amounts of ferrovanadium (20 pct V) and clean electrolytic iron totaling approximately 70 g. The first few heats were made in alumina crucibles with an insufficient amount of vanadium so that no oxide of vanadium would be precipitated under the particular gas composition. All the heats were made at 1600 °C under a high preheat and with four parts of argon to one part of hydrogen in the gas mixture to prevent thermal diffusion. The rate of gas flow was maintained constant at 250 to 300 ml per min of hydrogen. The time for each heat was three quarters of an hour after the melt had melted and attained the required temperature (1600°C). The water-vapor content of the entrant gas mixture was gradually raised in succeeding heats, keeping the vanadium content of the melt constant. This was controlled by manipulation of saturator temperature. A point was reached when for a given H2O:H2 ratio some of the dissolved vanadium was oxidized and appeared as a thin, bright oxide film on top of the melt. By raising the temperature of the melt it was possible to dissolve the oxide film which reappeared as soon as it was cooled down to 1600°C. The temperature readings taken on the oxide film were consistently higher by 80" to 85 °C as observed by the optical pyrometer. The heat was allowed to come to equilibrium under a partial covering of this oxide film. At the end of the run the power and preheater were shut off and the crucible containing the melt was lowered down into the cooler region in the furnace. This method of quenching proved quite

Jan 1, 1952