Search Documents

By Evangelo Agelopas

Steelmaking operators are familiar with the costs involved when ingot molds must be scrapped prematurely because of the failure of a stripping or turning lug. Some mold sizes can be expected to produce one hundred or more ingots per mold before normal wear causes the mold to become unserviceable. Therefore, the failure of lugs at less than the average life for that mold size represents a sharp increase in terms of mold cost per ingot ton produced. To combat these wasteful and costly occurrences, it was determined that an efficient method of replacing lugs should be developed to extend the life of molds which are otherwise in good condition. The purpose of this paper is to describe a lug welding method which has proved effective and economical. This method is known as the Oxygen and Mapp Process.

Jan 1, 1972

By H. T. Byck

THE plastering properties of six representative California drilling muds were studied over a temperature range of 70° to 175° F. at several mud weights, using a high-pressure circulating filter press with full size consolidated cores. In all tests, with untreated as well as with chemically treated muds, the filtration rates at elevated temperature were higher than at low temperatures and in nearly every case this increased filtration rate was notably larger than could be attributed alone to the decreased viscosity of water-the flowing medium-at elevated temperatures. It is concluded that no existing method will permit even an approxi-mate determination of the filtration rate at high temperature from data at room temperature. It is necessary to measure filtration at the tem-perature actually anticipated in the well, or to make a sufficient number of tests at various lower temperatures so that a small extrapolation of these data to the anticipated well temperature may be applied. Such tests should be carried out on the mud as actually used in the well. The viscosity of each of the muds was determined over the same temperature range. While no relationship was observed between mud viscosity and plastering properties, it was found that chemical treatment of the muds for viscosity reduction shifted the temperature of minimum viscosity to appreciably higher values than for untreated muds.

Jan 1, 1939

By Dennis V. D’Andrea, Robert C. Steckley, William C. Larson, Richard A. Dick

A fragmentation experiment was performed in cooperation with Duval Corporation in a porphyry copper molybdenum deposit near the Sierrita pit south of Tucson, Ariz. A 10-hole test blast was detonated to establish relationships between blasthole spacing and the resulting fragmentation. Blastholes were 9 in. in diameter and 110 ft deep. The 10 blastholes contained a total of 17,400 lb of aluminized slurry blasting agent in 50-ft columns with 60 ft of stemming. Blasthole spacings of 25, 20, and 15 ft were tested. Diamond drill core examination was the primary method used to determine the condition of the rock before and after blasting. Topographic surveys were used to measure the rock swell produced by the blast and a fragment size distribution was obtained for the rubblized material on the surface. The rubble zone at the surface was ideal for in situ leaching. Fragmentation to depths of 110 ft was excellent from the 15- to 20-ft blasthole spacing patterns. Good breakage was also produced by the 25-ft pattern although the effects of the blast were not as obvious. In situ leaching tests were not conducted. However, based on size consideration only, all three blasting patterns produced adequate breakage for successful leaching.

Jan 1, 1974

By Franklin Moeller

Discussion of the paper of FRANKLIN MOELLER, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 343 to 354. K. A. PAULY, Schenectady, N. Y.-I read with interest Mr. Moeller's paper descriptive of the mechanical parts of the new electric hoist at the Granite Shaft of the North Butte Mining Co. and as the paper treats largely of the mechanical equipment I have little discussion to offer. There is, however, one question which I would like to ask and that is, why the discrepancy in hoisting cycles between the curves given in the paper read by Mr. Sykes for the American Institue of Electrical Engineers at San Francisco and those given in the paper under discussion? In Mr. Sykes' curves the acceleration period is shown to be 16 sec. for all depths from 2,000 to 4,000 ft. inclusive, while Mr. Moeller in Fig. 2 shows 25 sec. throughout the range and in Fig. 4 shows 35 sec. Mr. Moeller's curves also show the following reductions in the peak load during acceleration: Level, Feet Mr. Sykes, Horsepower Mr. Moeller, Horsepower 2,060 3,500 3,130 3,000 3,800 3,480 Fig. 2 4,000 4,100 3,800 2,250 1,595 Fig. 4 As the purchaser's specifications called for 15 or 16 sec. I would like to know whether or not any modifications have been made in the requirements since the equipment has been installed.

Jan 5, 1916

By Garth M. Crosby, F. McIntosh Galbraith, Bronson Stringham

THE Hercules mine is located in the northeastern section of the Coeur d'Alene district, approximately 1 1/2 miles north of the town of Burke, Idaho. Surface indications of the ore deposit were first discovered in 1886, but regular mine production was not started until 1902 and was continuous until April 1925, when the known ore had been extracted. Incomplete records show that from 1912 until operations were suspended the mine produced 2 1/2 million tons of ore containing 9.4 pct lead and 7.7 oz of silver per ton, together with an estimated 2 pct zinc, 0.3 pct copper, and 20 pct iron. This operation was the first in a series of mining enterprises culminating in October 1947 with the consolidation of Day Mines, Inc. In the same year it was decided to unwater the levels below the collar of the Hercules shaft in the hope of finding some indication of a recurrence of ore. The unwatering operation has been described in a previous paper.1 The initial exploration, following recapture of the workings, showed sufficient promise to warrant a detailed study of the mineralogy with modern techniques.

Jan 12, 1953

By William C. Cooley

INTRODUCTION Considerable research has been conducted on the use of steady and pulsed jets of water at high pressures to produce slots or holes in rock, and to fracture rock. The primary objectives of prior research have generally been to determine the feasibility of excavating or drilling rock or minerals and to determine the optimum jet parameters for this purpose. The present study was undertaken in order to identify the pertinent dimensionless parameters involving jet and rock properties which characterize the liquid jet penetration process and to develop empirical correlations of the existing test data which would permit engineering prediction by means of scaling relationships. The present paper is in the nature of a progress report, because not all the existing test data have been processed. Also effort has been concentrated on correlation of data on the specific energy (jet kinetic energy per unit volume of rock removed or broken), rather than correlation of jet penetration depth, hole diameter, kerf depth or kerf width. However, it is clear that this method of correlating data on specific energy in terms of dimensionless parameters shows great promise and provides insight into the nature of the physical processes of jet erosion and fracture. It therefore can help to avoid drawing incorrect conclusions from limited experimental data. DIMENSIONAL ANALYSIS The method of dimensional analysis is particularly valuable where the mathematical relationships controlling a physical process are unknown or complex. The grouping

Jan 1, 1971

By H. L. James

THIS paper presents the results and analysis of field trials of various magnetic instruments over anomalies ranging from 20 to 5000 gammas of vertical intensity. The following instruments were used: Askania vertical magnetometer, Wolfson vertical magnetometer (model M-I), Hotchkiss Superdips (used both parallel to and normal to the magnetic meridian, with several settings of the "sigma" angle), Lake Superior dip needle, and the dipping circle for measurements of inclination. The change in inclination over the measured anomalies ranged up to 4°; this caused pronounced changes in sensitivity of the Hotchkiss Superdip oriented parallel to the magnetic meridian. The variable sensitivity not only gives apparent displacement of crests of anomalies, particularly at high sensitivities, but also makes the data difficult or impossible to use in preparation of iso-anomaly maps. This weakness in field performance of the Superdip is shown to be eliminated by orienting the instrument normal to the magnetic meridian and measuring vertical intensity only, which in the latitude of upper Michigan is equal to 97 pct of the total intensity. The dip needle is seen to be relatively ineffectual for location of anomalies of less than 400 gammas.

Jan 1, 1947

By G. R. St. Pierre, L. M. Adelsberg, R. Speiser

OXIDE platelets have been observed'-3 in oxidized tantalum adjacent to the metal-oxide interface, Fig. 1. The origin and identity of the platelets are important with respect to the proposal of an acceptable mechanism of tantalum oxidation. At reaction temperatures below 750°C, it has been established that the platelets

Jan 1, 1967

By W. Scott Dunbar

INTRODUCTION Methods of linking boundary integral (BI) solutions with finite element (FE) solutions have been well described theoretically in other publications (e.g., Zienkiewicz, et al., 1977). The purpose of this paper is to point out some practical aspects of implementing these linkage algorithms for rock mechanics applications and to describe an alternative linkage algorithm. A not so obvious motivation for using FE-BI linkages is illustrated in Figure 1. The cost of modeling the excavation of the crusher station by the BI method can equal or exceed the cost of an equivalent FE model. This is due to the large surface area which must be modeled by the BI method. In such cases, a more economical approach might be to model the region immediately adjacent to the crusher station by finite elements and link the solution at the periphery of the FE model with a solution for the exterior region. Further economies can be realized if some flexibility in the type of exterior solution is possible. For example, it would be desirable to use a coarse discretization of the FE-BI interface for a BI solution, which would be less demanding of computer storage and time, or to use an analytical solution for the exterior region. The alternative linkage algorithm to be discussed allows such flexibility. BOUNDARY INTEGRAL METHODS There are basically two formulations of BI methods: the direct and the indirect. FE-BI linkage algorithms depend on which formulation is used. The purpose of this section is to briefly describe each method.

Jan 1, 1982

By Mark R. Lamb

The various methods of treating pulp in air-agitation tanks offer problems for experiment and study which are fascinating as well as practical. The usual method heretofore has been to fill each tank in turn, agitate the mixture the required period and then discharge the treated pulp into a storage-tank, from which it is drawn to the filter as required. A later method is to run the pulp from the tube-mill, classifier, thickener, or settler into the first of a set of tanks, and thence continuously or in series through the remaining tanks, finally drawing off the pulp to a continuous filter, or to a pulp-storage tank if the filter is of the intermittent type. It is this method which I propose to discuss here in a preliminary way, with the idea of going exhaustively into the examination of the results of a series of experiments in a later paper. It may be of interest to note that the design of a cyanide-plant has recently been completed in which the estimated cost of the agitation-tanks, storage-tanks, and pumps was 30 per cent. higher for the charge-agitation arrangement than for the series plan. The first question in studying the series method is, " What is the actual period of treatment undergone by the pulp ?" One first supposes that by chance some of the pulp may get through with little or no treatment, while other portions may stay in the tanks a needlessly long period. The former is not probable or even possible, and the latter is, practically, true

Jan 1, 1910

By H. Hance James

SOME of the outstanding features of petroleum production in Illinois during 1923 were: (1) Sustained production from the older wells, due to cleaning and deepening; (2) good results from new drilling in a few localities; (3) large percentage of dry holes, many of which were ill advised tests, with a resulting high cost of the new production; (4) decrease in the number of productive wells in the state; (5) low average price of crude petroleum, a serious factor over the entire country. FIG. 1.-ANNUAL TOTALS OF ILLINOIS PRODUCTION. The total production of Illinois for 1923 was 8,710,000 bbl.,1 a decrease of 7.2 per cent. from that of 1922. Of this amount, it is estimated that about 8,500,000 bbl. were produced by old wells, many of which had been cleaned and deepened somewhat, and approximately 210,000 bbl. were obtained from the new wells drilled during the year. About 95 per cent. of the oil comes from the southeastern field in Clark, Crawford, and Lawrence Counties, where production is almost entirely from Pennsylvanian and Mississippian rocks. Extensions of the productive area were made in Clark, Wabash, Marion, and Jackson Counties. Some important gas development has been accomplished near Jacksonville, in Morgan County, and at Gillespie, in Macoupin County.

Jan 3, 1924

By E. J. Quinn, M. F. Fogler

In a recent paper, Rawdon and Mutchlerl gave some exceptionally interesting results on the Brinell and scratch hardness of severely cold-worked metals. In their work, they found that, on continued cold rolling, the metal hardened up to a particular point and then reversed and became softer; this was true for both Brinell and scratch hardness values. The generally reported behavior2 of metals, with respect to Brinell tests on cold-worked material, is that the metals harden up to a certain point and then, on further cold rolling, no change in Brinell hardness occurs. Jeffries and Archer3 state that there is little difference between the scratch hardness of annealed and cold-worked metals; the work of Faust and Tammann4 also indicated no difference between the hardness of annealed and cold-worked copper. Rawdon and Mutchler found, when they plotted the reduction ratio (initial thickness divided by thickness after rolling) against the hardness value for the cold-rolled material, that the hardness number increased up to a reduction ratio of about 3 and then decreased and became even smaller than that for the annealed metal. This behavior was reported for both scratch and Brinell hardness; Figs. 1 and 2 show their results for Brinell hardness on the metals for which they published data. This is an exceptionally interesting phenomenon, if it occurs under all conditions of rolling, and would have an important bearing on the practice of cold

Jan 1, 1925

By Vernon Read

Among the technical problems in AEC's Project Plowshare is the necessity of determining the precise effects of nuclear blasts in all kinds of ground formations. This calls for extensive in-situ sampling with full core recovery. In the exploration drilling that often precedes a new test detonation, the AEC and its contractors have applied both novel and established sampling techniques in many new ways, giving improved core recovery and reduced costs in all subsurface sampling and testing. Unique among these new techniques is one that achieved full recovery and virtually undisturbed samples from near-surface layers of unconsolidated boulder-strewn alluvium. This approach involves a combination of oilfield and mining core drilling equipment. Oilfield heavy drill collars, rotary stabilizers and thick, vibration-reducing oil emulsion drilling mud were used in combination with the precise hydraulic feed control, fast (over 300 rpm) bit rotation, light drilling weight, hard rock core barrels and multi-step diamond bits that are common in mining industry diamond drilling.

Jan 8, 1963

By R. J. Batterham, P. W. Roller

Granulated sinter mixes of three iron ore types were prepared with a range of water contents in a laboratory investigation. The mean diameter of the granulated mixes and the void fraction of beds of the mixes were determined experimentally. Pressure drop measurements over a range of flow rates were made in a laboratory permeameter with pressure tappings at several depths in the bed. The Ergun equation was applied to the results to determine the shape factor of the granulated mixes. Pressure readings down the bed were used to estimate the local void fraction in the bed using the Ergun equation and the calculated granule shape factors. It was found that there was a decrease in void fraction with depth in the bed. The significance of this and the variation of shape factor values with the amount of water used for granulation is examined in relation to the strength of granules of the sinter mixes. The experimental and mathematical techniques presented may be useful in interpreting the behavior of the permeability of sinter beds after ignition.

Jan 1, 1986

By Theodore Nagel

Fuel-oil, natural gas and coke oven gas, producing the higher temperatures of open-hearth current practice, have been gradually displacing producer gas the lowest cost fuel for open hearth operations. The lower temperatures of combustion products from producer gas is caused by nitrogen dilution. Practical Application of Combustion Thermochemistry One pound of carbon burned to CO produces 3,960 B.T.U. and one pound of carbon burned to C02 produces 14,140 B.T.U. The second unit of oxygen uniting-with gasified car-bon (-CO) produces (14,140 - 3,960) 10,180 B.T.U. which is;(10,180 - 3,960) 6,220 B.T.U. more heat than produced by the first, unit of oxygen forming CO by uniting with solid carbon. A review of the relative combustion heating values of commercial gaseous fuels reveals CO requires a minimum of air for combustion, and because of minimum nitrogen dilution and the high thermal release from CO higher temperature combustion products are produced from CO than from natural gas or from coke-oven gas under similar combustion conditions. Inert nitrogen diluent lowers the calorific value of fuel gas and its diluting effect is cumulative in lowering the temperature of the products of total, combustion. It is not only logical but, practical in partial combustion, converting bituminous coal to gas, to generate the gas, with reduced nitrogen dilution.

Jan 1, 1936

By Carl S. Westerberg

1,. C. McCABE*-—An increased derliand for coal in the west is to be expected because of the growth in population and industry during the past ten years. The author calls attention to the increased mechanical cleaning of Utah coal between 1938, when no cleaning was being done, and 194.7, when more than 24 pct of the production was cleaned. This is essentially the Period of most rapid growth of the Pacific Coast. area altliough the growth and, no doubt, the general trends in coal production and cleaning continued at a less accelerated rate during 1948. The Pacific southwest increased 37 pct in population between 1940 and 191.7 while the United States showed only a 7 pct increase in the same period. it has been estimated that there will be an additional 15 pct increase in population between 1947 and 1950. The conclusion that more coal and more mechanicak cleaning capacity will be required appears to be well founded. Mr. Westerberg discusses the cco- nomic advantages of coal cleaning reflected in freight savings, in lower cost per million Btu, and lowered ash and sulphur content. In view of the limited occurrence of coking coals in the west it would be interesting to know whether significant beneficiation in coking strength can be expected from mechanical cleaning of Utah coals. This has been demonstrated for some eastern and midwestern coals. One can readily agree to the desirability of recovering the fine coal that has heretofore been lost in washery slurry. The very cheapness of coal has Iridered

Jan 1, 1950

By Nobuhiro Takahashi

PROLOGUE The Yaguki mine, which is located near the southern end of the Tohoku region, Japan, near the coast of the Pacific Ocean, had had a long history as a copper mine, but had not been operated since 1925. About 30 years later it was reopened by Nittetsu Mining Company, and in 1958 a small flotation and magnetic separation plant, a so-called test plant, started production. The ball mill the author first met, a 8x4x4x7 ft tricone mill, called No.1 mill, had started running at that time. With his experience in initial, running of this mill he realized that the ball mill was not simply a preparatory process to flotation, but a determinant factor for flotation performance, an energy-consuming and costly process, and that its operation control was an important task in the plant (1). The working part of an operating ball mill is the ball load inside, whose properties govern the grinding performance. Its size distribution affects the efficiency greatly and the capacity is nearly proportional to its weight. When a ball mill operates for a long period of time with a constant and consistent addition of renewal balls, wear and renewal of balls are balanced, and an equilibrium ball load is formed. A stable equilibrium load is the primary requirement for a stable ball mill operation. However, renewal ball size would be the most influential factor affecting efficiency and capacity of operating ball mills. To improve efficiency, to increase capacity, or to get finer product, attempts to find out the optimum size assortment of renewal balls should be made. When re-

Jan 1, 1976

By R. Neilson Clark

The discovery of a thin pay streak, yielding carbonates of copper; native silver, and perhaps chloride of silver, was made on the 9th of April, 1874, within the trachytic belt which forms part of the Sierra Mojada. The discoverer named it the Humboldt Mine. On the 2d of May, 1874, another discovery was made, in a northwest direction from the Humboldt, at about five hundred feet distant, this was named the Pocahontas Mine. After some exploration these two discoveries were proven to be on the same vein. To the southeast of the Humboldt a claim had already been taken up, called the Virginia; and to the northwest of the Pocahontas, one called the Southeast Leviathan. On these' last two this same vein has been found and worked. This paper will therefore treat of the Humboldt-Pocahontas vein, as worked on these four claims, to wit: beginning at the northwest, the Southeast Leviathan, the Pocahontas, the Humboldt, and the Virginia claims. Since the spring of 1874, there has been sunk on this vein a total of twenty-seven hundred and fourteen feet of

Jan 1, 1879

By R. V. Whetsel, V. R. Gargias, J. W. Ristori

WoRld consumption of petroleum and its substitutes in 1941, the amount of which obviously is largely conjectural, is estimated at 2,066,653,000 bbl. This is 48,689,000 bbl. more than the previous year and is an all-time high. Except for the United States, this figure does not include consumption for military purposes. Consumption in the United States also reached an all-time high during 1941, totaling 1,492,000,000 bbl., or 158,230,000 bbl. more than the previous peak year of 1940. On the other hand, it is estimated that civil consumption in countries outside of the United States decreased 109,541,ooo bbl. as compared with the previous year. Demand for military purposes and/or additions to stocks in countries outside of the United States is estimated at 304,507,000 bbl. during 1941, compared with 209,635,000 bbl. in 1940. This increase was due largely to blitzkrieg warfare on several fronts. especially Russia; entailing large expenditures of petroleum by both sides because of the immense area covered by the fighting forces, the long supply lines necessary and the intensity of the fighting. It is interesting to note in this connection that Axis-controlled countries, excluding Japan, had an estimated production of approximately 89,000,000 bbl. of petroleum and its substitutes in 1941. The peacetime consumption of these countries in 1938, for example, was about 183,000,000 bbl. It is believed that the minimum to which civil consumption could possibly be re-duced in wartime is 20 per cent of that of peacetime, which would call for a minimum consumption of 37,000,000 bbl. in these countries in 1941 for civil purposes. This

Jan 1, 1942

By Gilbert H. Cady

HE application of geology to problems arising A in coal mining engineering and coal preparation has, in general, been somewhat remote, or the geological problems have involved such simple forms of geological knowledge that the attention of specialists in this field has not been commonly thought necessary. Furthermore, the geology of coal beds and coal mining has received but scant attention in our educational system, even in mining education; so that coal mining engineers have become somewhat conditioned against geological thinking. Geologists, on the other hand, have commonly failed to realize that there are geological aspects to coal mining and coal preparation problems. A further reason why geology receives so little consideration in coal mining undertakings in this country lies in the fact that our coal supplies are, or have been thought to be, almost unlimited, have been easily accessible, and very cheaply mined. Conditions have been changing within recent years. Failures can be less easily endured. Great inroads have been made on our bonanza deposits of easily mined coal and the increasing cost of coal and the increasing difficulty of finding it in easily accessible and large quantities places greater and greater importance on accurate information and good technique in exploration. It seems probable, therefore, that the opinions and aid of geologists will be more commonly sought than in the past in the exploration for coal and in the development and operation of coal mines, and analyses of mining conditions, preparation, and utilization.

Jan 1, 1951