Search Documents

By Peter Haasen

INDIUM antimonide has the zincblende structure. A possible defect that does not disturb the indium tetrahedron surrounding any antimony atom in this lattice (or vice versa) is obtained when neighboring

Jan 1, 1958

By J. B. Newsom

IN the Indiana limestone district, some 50 or 60 per, cent of the merchantable stone in a quarry opening is waste, and only about 40 or 50 per cent of the stone from the opening is finally sold. So long as the present system of quarrying is used, the wastes measured and reported in this paper will continue. Comprehensive development of an entirely different method of quarrying, using wire saws for cutting, promises great improvement. Some of the savings to be expected are pointed out in the following pages. No attempt has been made to measure losses due to variations and natural flaws in the stone, since these vary greatly in different quarries, and accurate measurement would be difficult. The wastes that have been measured account for about 30 per cent of the total ledge, which leaves 20 or 30 per cent chargeable to unmeasured sources of loss.

Jan 1, 1932

By O. W. Walvoord

ONE particular plant has been chosen to illustrate the various factors in mill design. The problems are general in nature and with various modifications are met in the design of most milling plants. Literature on modern mill design is not extensive and certainly has not kept pace with the rapid advancement in the art of ore beneficiation. Much remains to be investigated, and continued vigilance is required to give the operator and the metallurgist the best layout to meet the industry's changing requirements. The Humboldt project, a joint venture of the Cleveland-Cliffs Iron Co. and the Ford Motor Co., involves an iron ore flotation plant near the town of Humboldt, on the Marquette range of the Michigan Upper Peninsula. A crushing plant, designed for an ultimate capacity of 720 long tons per hr, is followed by a first mill unit of 70 long tons per hr. Future mill units are planned to bring the total mill capacity to 5000 long tons per 24 hr.

Jan 1, 1954

Papers in Classes A-Metal Mining, B-Milling and Concentration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Papers in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. Papers in Class G-Petroleum Division are distributed in PETROLEUM TECHNOLOGY, which is issued every other month. TECHNICAL PUBLICATIONS in Classes F-Coal Division, J--Mineral Industry Education Division, K¬-Mining Administration, and 1-Geophysics, are issued as separate pamphlets. Contributions are papers that when printed or mimeographed are available but only on request.

Jan 1, 1944

By D. R. Maneval

The Surface Mining Act of 1977 required a study by the National Academy of Sciences regarding the special mine reclamation requirements of Alaska. The status of mines operating and planned in Alaska will be presented. New mines opening in Alaska must establish a baseline inventory of plants and animals in the mine site area as well as determine pre-mining air and water quality. Current work in these areas will be summarized. Reclamation practices in Alaska and other Arctic countries as practiced currently will be described. A summary of current research in Alaska dealing with revegetation on surface mined lanais, re-establishment of animal populations, and water treatment processes necessary in this pristine environment will be discussed. Included will be future predictions of the direction of mine reclamation in Alaska as more mines enter the industry.

Jan 1, 1984

By J. de la Vergne, L. O. Cooper

The hydrostatic steel mine shaft liner (HSL) Provides a permanent wall lining for drilled shafts. It is watertight and suitable for bad ground conditions. After a shaft has been drilled to its full depth, the HSL is lowered into it and secured in place with cement grout. The liner consists of a cylindrical steel shell usually reinforced with exterior stiffening rings. The shell is basically designed for compressive strength and the rings are provided to give the shell added resistance to buckling. There are no published standards for the correct procedures to design an HSL. This paper gives a method that appears logical. A design solution can be complex with increased opportunity for error. This paper presents simple formulas to produce sufficient accuracy for construction design. Two new concepts are presented, referred to as transition pressure and critical pressure. An example demonstrates use of the formulas and concepts presented. To facilitate comprehension and use of the formulas, Greek letters are avoided and most of the English alphabet symbols used refer by association to their definitions. An appendix shows derivation of the formulas.

Jan 1, 1984

The war story of the engineer corps at home and in France is told officially for the first time in the advance sheets of the War Department's brief history of American war efforts. Many of these accomplishments have been published before as isolated incidents, but they gave no idea of the extraordinary duties modern warfare has laid upon engineering troops. In the engineering units that reached the other side, there were seven regiments and two battalions of railway construction engineers; five battalions for maintenance of way; two battalions for maintenance of railway equipment; four regiments and one battalion to operate the main American railways in France; three regiments to operate light railways and their repair shops; two regiments to operate the regular railway repair shops; two regiments and six separate battalions on general construction work; two regiments for storing and transporting engineer supplies; a forestry regiment; a light-railway construction regiment; a roadbuilding regiment; a water-supply regiment; a mining regiment; a quarrying regiment; a technical regiment for surveying and sound ranging; three survey and printing battalions; two railway transportation battalions; an electrical and mechanical regiment; several separate companies to operate cranes; a camouflage service; five inland waterway companies, to operate canal boats and the like; five pontoon trains and a pontoon

Jan 6, 1919

By W. C. Winegard, C. J. Simpson, C. J. Beingessner

VARIOUS organic compounds, such as borneol, carbon tetr a bromide, and hexachloroethane, solidify as transparent plastics with a fcc structure. Each of these substances undergoes a solid-state transformation from the plastic phase to a brittle phase at temperatures slightly above 20°C. Since it was known that these plastic crystals solidified like metals,1 it was decided to investigate the possibility that solid-state grain growth would occur in the same way as it does in metals. Two-dimensional grain growth in thin films of plastic organic compounds has been studied with the aid of cinemicrophotography. Samples varying in thickness between 250 and 1000 @ were prepared by subliming a thin layer of the compound onto a microscope slide plate which was then covered with a second slide plate.

Jan 1, 1968

By D. G. Peterson, W. J. Guay

The extraction of gold from refractory ores containing activated carbon and various types of carbon compounds is being done commercially for the first time at Carlin, Nev., by Carlin Gold Mining Co. Oxidation of the carbonaceous materials to CO and CO,- is accomplished by the introduction of chlorine into an aqueous pulp. The chlorine reacts with the limestone in the ore to form calcium hypochlorite which in turn reacts with the carbonaceous matter to form calcium chloride, CO, and CO.. Following the oxidation treatment the ore is cyanided in the conventional manner. For the first six months of operation the plant averaged 83% extraction at a feed rate of 500 tpd and a consumption of 28.4 lb chlorine per ton of ore which showed only 33.5% extraction by conventional cyanidation without the oxidation pretreatment.

Jan 1, 1974

By Gail Moulton

THE oilfields in Illinois are located principally along the LaSalle anti-cline in the southeastern part of the state. The oil produced comes most largely from beds of Pennsylvanian and Mississippian age, but there is an increasing important production from deeper horizons, as will be noted under new development. The oil is largely of paraffine base, and has an average specific gravity of about 35° Baume. The rank of Illinois as an oil producer has dropped from third since 1913, when its production was exceeded only by that of California and Oklahoma, to eighth in 1923. This has been the result of failure to find new pools of considerable size to offset the declining production of the old wells and of the greatly increased production of some of the other states. The noteworthy features of petroleum production in Illinois during 1924 are: the low rate of decline for the state as a whole; the smaller percentage of dry holes; and the larger average initial yield of the new wells.

Jan 3, 1925

By F. D. DeVaney

IT is of great interest that the various organizations engaged in the search for a cheap and efficient agglomeration process for fine magnetite concentrates-essential if the taconites are to be utilized-have ended up with processes that are basically different. This paper describes the development and the present status of the shaft-type furnace as now utilized by the Erie Mining Co., which is managed by Pickands Mather & Co. The shaft furnace has always had an appeal to metallurgists because of the simplicity of the design and the possible low fuel consumption. Work done on pelletizing at the University of Minnesota Mines Experiment Station by E. W. Davis and his associates determined that it was possible to roll up fine magnetite concentrates in a balling drum, and that, if such balls were fired at a sufficiently high temperature, a hard, indurated pellet, well adapted for use in a blast furnace, could be made. Early furnaces had no heat recuperation and the heat consumption was in the order of 2 million BTU's per long ton.

Jan 3, 1958

By Raphael D. Schilz, Michael F. Dunn, Edward D. Thimons, Francis S. Kendorski

During a mine fire or other emergency, it may be desirable to reverse the air flow in order to provide an escapeway or to control a fire. Also, in colder areas, the air flow may be reversed to prevent ice build-ups. When reversing main mine fans, the operator usually does not know what operating characteristics of flow and pressure to expect. Laboratory testing of vane axial main mine fans has been completed in order to establish forward and reverse performance characteristics under controlled conditions, with the results presented here. Preliminary tests under field conditions have also been conducted. The data obtained suggest that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. There is also evidence that reverse performance can he predicted for a family of blade angles in a given hub to tip ratio. In general, the air quantity delivered by the fan is 30% to 60% less in reverse than when operating in the normal forward mode.

Jan 1, 1982

By Richard E. McElvain

The mining and other industries have grown and changed with- respect to their requirements for slurry pumps capable of handling high percentages of abrasive materials. Greater solids concentration, higher heads and pressures, and increased flow arc not possible. Today's equipment delivers up to three times the flow-tonnage and 1.3 times the head per stage as compared with pumps of ten years ago. This results in four times the requirement in size and energy. The new centrifugal pumps are capable of handling these requirements at pressures up to 4826 kPa (700 psi), with 6895 kPa (1000 psi) or more being considered for future systems. The latest pumps, functioning at four times the operating requirement on flow-head, weight eight times more than the previous equipment. Efficiency is increased slightly, to about 75 % to 85%. A testing program on equivalent units has confirmed that the added strength and specific design of heavy-duty pumps can meet demanding engineering objectives. Operating life on difficult-to-pump materials is increased from 500 to over 5000 hours of continuous operation; the ten-fold increase in pump operating time is a major design objective.

Jan 12, 1976

Later this month (June 24-27) in San Francisco, the Society of Mining Engineers of AIME, together with the American Society of Civil Engineers, the Canadian Institute of Mining & Metallurgy and the Engineering Institute of Canada, is sponsoring the second biannual Rapid Excavation and Tunneling Conference. The dominant theme of the Conference is the practical application of techniques and research relating to underground rapid excavation and tunneling. In the following pages, ME gives highlights of many of the 24 technical sessions and some of the papers being presented. The full proceedings of the Conference will be published by SME-AIME later this year.

Jan 6, 1974

By D. O. Rausch

The economic relationship between steepening slopes and decreasing waste removal requirements ahead of ore mining is one of the most important factors in the design of open-pit mines. The steepness and stability of the pit slopes often spells the difference between ore and waste profit or loss in low cost open-pit operations. Unfortunately, the technology necessary for designing stable rock slopes is still in the early stages of development. Past and current pit-design methods have been, and still are, empirical, with rock slopes frequently made too steep or too shallow. As such, large expenditures are often made for correcting slopes after failures occur, or for unnecessarily removing more waste material than required.

Jan 6, 1965

By John Batchelder, David W. Blake, Ted. G. Theodore

The Copper Canyon CIL-Au-Ag deposits include two geologically distinct hypogene ore bodies developed primarily in late Paleozoic rocks adjacent to a 38-m.y.old potassic-altered granodiorite, whose emplacement seems to have been controlled largely by the Virgin fault, a north-striking normal fault. Widespread but subeconomic concentrations of sulfides as fracture and cavity fillings in skarn apparently preceded the final intrusion of the granodiorite. In the west ore body, metals reached ore-grade concentrations through the massive replacement of andradite by chalcopyrite, pyrrhotite, and pyrite mineral assemblages. The east ore body probably formed after the granodiorite reached its present level. Data suggest that fluids associated with potassic alteration here were most likely composed of magmatic water mixed with some meteoric water.

Jan 1, 1977

By A. Kenneth Schellinger

IF the ball mill is considered only from an energy standpoint, it can be thought of as a converter of kinetic energy into heat energy and surface energy. The law of the conservation of energy must apply to the ball mill as it does to any machine or process in nature. The heat energy output of the ball mill is apparent to any casual observer of the operating mill since the outflow pulp will be appreciably warmer than the inflow water and rock. The rock in the ball mill is crushed by shearing of its ionic bonding caused by some impact-induced stresses beyond the elastic limit. As the bonds holding the mineral crystal lattices together are ruptured, new surface area is created on each unit of which a definite number of unsaturated bonds exist. Such unsaturated energy of bonding may be termed the "surface energy," and is a potential energy figure. This created energy was withdrawn from the ball mill system and represents an absorption, or disappearance of heat. To reduce the size of the rock, surface area must be created and with it the at-

Jan 6, 1951

By Ralph Sherman

IN these days of intense competition for the domestic fuel market much is heard of the low efficiencies with which solid fuels, and most particularly bituminous coal, are burned in domestic heating equipment. In contrast to the every-day operating efficiencies of 85 and 90 per cent in large, central, electric-generating stations, efficiencies of 50 per cent and lower are cited for the hand-fired home furnace. Just as the miles per gallon of gasoline is only one of the factors that determine the cost of operation of an automobile, so the thermal efficiency is only one factor in the cost of domestic or other heating. The purpose of this paper is to analyze the total costs of domestic heating by various fuels and types of equipment, to determine the relative importance of efficiency and other factors, and to discuss what this signifies relative to the future of the use of fuels in the home.

Jan 1, 1933

By Yoshinao Nakada

In many experiments involving electropolishing such as electropolishing during deformation and electrothinning of deformed metals for electron microscopy, it is usually assumed that the specimen temperature is the same as the temperature of the polishing bath. In order to test this assumption, the interior temperature of aluminum single and polycrystals was measured while they were being electropolished. Specimens were 1/4 by 1/4 by 6 in. and were of 99.99 pct purity. A small hole 1 in. deep was drilled axially at one end of the specimen so that a copper-constantan thermocouple could be inserted. The electropolishing solution was 4 parts methanol (reagent grade) and 1 part perchloric acid (70 pct). The electropolishing was performed using an apparatus shown in Fig. 1. The electropolishing solution was stirred by a motor-driven stirrer and was cooled to —5°C with a mixture of methanol and dry ice. Electrolyte temperature was measured and remained at -5°C during the electropolishing. Current density of 0.3 amp per sq. cm was used. When the current was turned on, after about a 5-sec delay, the temperature began to rise rapidly until it reached 65°C. In order to determine whether the temperature measured was localized, the thermal expansion of the specimen was meas-

Jan 1, 1965

By E. V. Manlapig, David J. Spottiswood

In recent years great advances in the automatic control of flotation plants have been made, mainly due to the development of reliable sensing instruments to monitor process performance and the development of an adequate understanding of system responses to process disturbances. Some of the control strategies used in flotation plants which apply computer control are presented here. These schemes, which involve the control of collector; depressant, frother, and air and pulp level, are analyzed with respect to their control objectives, control variables, and the instrumentation involved. The knowledge gained in understanding these strategies may be applied in the dew and implementation of control system in other concentrators.

Jan 1, 1981