Search Documents

By Sydney H. Loram

TEIS paper, which is merely an arrangement of data collected during several hurried journeys, is offered to serve as a record, until such time as a better substitute be compiled. My observations were confined, as far as possible, over the entire distance, to the actual river valley; because near the Central Cordillera the country is so mountainous as to be im; passable in any direction but that of the dominant valleys. The river is not navigable anywhere, and for the first part of its course is a mountain torrent that runs down the bottom of narrow, almost vertical-sided valleys, through which the only road requires repeated fording, and often following up the bed of the stream ; but the rock-walls, standing clean and free from debris on either side, present the different formations with remarkable distinctness. A topographical map and a cross-seetion of the Rio Huasco is given in Fig. 1. The Rio Huasco practically rises from Laguna Grande, a lake about 17 km. from the Argentine boundary, and 3,135 m. above se-level, which is fed by direct snow-water, and by a few streams varying from a considerable volume, when supplied by the melting snow, in late spring, to little or nothing during the rest of the year. It is a somewhat pear-shaped body of water, about 1.5 miles in length and half a mile in average width, with a reported maximum depth of 45 meters. It was formed by the choking up of a narrow continuation of the same valley with blocks of an agglomerate mentioned later. The present level is some 5 m. below high-water mark (to which point, according to local accounts, it has not been filled for 35 years). In the intervening margin is a calcareous deposit about 4 m. thick, formed by the rapid evaporation of the water in the exceedingly dry air, and aided by the capillary action of an aquatic plant, growing in thick masses around the edge of the lake. These masses, dying and banking up, form

Jan 1, 1905

By R. F. Domagala

SOME of the results of a program designed to study the kinetics of transformation and related mechanical properties of prototype Zr-X binary alloys systematically are presented here. The object of this program was to provide a sound basis for a scientific approach to the realization of optimum properties in binary zirconium alloys. Alloys of Zr-Mo (eutectoid), Zr-Sn (peritectoid), and Zr-Ti (a and ß isomorphous) were prepared and studied. The data herein are confined to a presentation of the results of studying the eutectoid prototype alloys. The Zr-Mo phase diagram has been determined.&apos; A definitive metallographic study of isothermaily annealed samples prepared from high purity elements served to position a sluggish eutectoid reaction, ß?a + ZrMo2, at 780°C. The compositions of the phases involved in this reaction are: ß, 7.5 ±1 pct Mo; a, <0.18 pct Mo; and ZrMo2, 67.8 pct Mo. Inasmuch as a lower purity sponge zirconium was used in this work boundary placements were rein-vestigated with the less pure alloys. Materials and Procedures Hafnium-free sponge zirconium was used to prepare all ingots. The arc melted hardness of a small button of this zirconium was found to be Vpn 168. Chemical analyses conducted at Armour Research Foucdation are shown in Table I, High purity molybdenum sheet was used as the alloy addition. A typical analysis is shown in Table I. Several 200-g Zr-50 pct Mo alloys were made by arc melting. Crushed granules of this material were used to ensure inqot homogeneity Ailoy ingots were prepared by double melting techniques. First, three 5-lb ingots of each alloy composition were are melted in 2 nonconsumable electrode arc furnace. After melting. the ingots were ground to remove surface defects. A subse-

Jan 1, 1958

By L. M. Barker

THE New Cornelia Branch of the Phelps Dodge Corporation is at Ajo, Pima County, Ariz. It is at the southern terminus of the Tucson, Cornelia and Gila Bend Railroad, which connects with the Southern Pacific Railroad at Gila Bend, Ariz., approximately 43 miles to the north. HISTORY Early history of the Ajo district has been related by A. W. Allen1 and by T. A. Rickard.2 Briefly, steps looking to the large-scale development of the ore body were instituted as early as 1912. This work culminated in the equipment of the property for open-pit mining by steam shovels. Ores initially mined carried economic amounts of copper carbonates as the principal copper-bearing mineral. Treatment methods developed for the extraction of the copper content involved leaching and a 5000-ton leaching plant was constructed and placed in operation in early 1917. Description of methods and equipment employed in this plant has been given by A. A. Tobelmann and James A. Potter.3 As exhaustion of the carbonate ore body neared, and mining operations exposed an adequate tonnage of sulphide ores, a 5000-ton concentrator was constructed for their treatment. That plant has been described by H. Kenyon Burch.4 Construction was completed and the plant was placed in operation in early 1924. Changes made in the original plant to improve practices and increase production will be the subject of subsequent paragraphs of this paper.

Jan 1, 1939

By H. S. Rankin, F. A. W. Davis, R. A. Laurence, L. L. McMurray, E. C. Houston

This paper is coodensed from several reports by members of the staff of the Minerals Testing Laboratory of the Tennessee Valley Authority, on a series of experimental tests in the beneficiation of barite of the Valley area. These experiments were conducted upon a large number of samples taken from several mines in three different districts. The area contains numerous producing deposits, nearly all of which are hampered by the high iron and silica content of the ores. Because of the small difference in specific gravity between the iron oxide and the barite, a gravity separation is generally poor. The removal of the iron thus offers a special problem. Some of the operators have turned to magnetic separation to meet the shipping requirements for less than one per cent iron. The present experiments were conducted to determine the application of decrepitation or flotation in simplifying the concentration of the barite by removing the iron oxide and silica in one operation. Practically all the barite marketed in the area has been as "off-color" crude. The bleaching studies were made to determine the bleach-ability of the ores to alleviate this inferior grading, placing them on the market as bleached barite. Geology Barite has been produced at many places in the Tennessee Valley area, and prospects and minor deposits are known at many other places, but practically all the production of barite in the Valley has been from the Sweetwater district of East Tennessee. Other leading areas of former production are the Tazewell-Russell counties areas of southwest Virginia, the Del Rio-Stackhouse district of East Tennessee and western North Carolina, and the Fall Branch district of upper East Tennessee. The areas described in this paper are those from which samples used in the concentration tests were obtained.

Jan 1, 1942

In 1803 the purchase of the immense territory called the province of Louisiana wm arranged between Thomas Jefferson, President of the United States, and Napoleon Bonaparte, First Consul of France. This central portion of what is now the United States was claimed in 1682 by the explorer Robert de La Salle for France, who continued to hold her title to the vast domain until 1762, when it passed by treaty to Spain, only to be retroceded to France in 1802, in consequence of Napoleon&apos;s military domination of Spain. Jefferson did not care to see New Orleans and its extensive hinterland pass into the hands of France. Spain did not matter so much; she was quiet and feeble, whereas France was restless and aggressive under Napoleon, who had dreams of founding a French colonial empire on the American continent. The expression of American feeling that Jefferson elicited came as a surprise to Napoleon, who concluded that a contest was not worth while, for his navy had been shattered by the English, and it was evident that only maritime supremacy could enable him to retain this trans-Atlantic possession; so he resolved to put it out of the grasp of England and at the same time replenish his military chest by selling Louisiana to the United States. The price was 60 million francs. By the terms of the Louisiana purchase a magnificent territory was added to the national domain; it covered more than a million square miles, or more than the total area of the United States at that time. Louisiana included the present States of Louisiana, Arkansas, Missouri, Kansas, Iowa, Nebraska, South Dakota, North Dakota, Wyoming, Montana, Oklahoma, with parts of Colorado, Idaho, and Minnesota; but

Jan 1, 1932

By Charles R. Fettke

The permeability of an oil or gas sand is its capacity for transmitting fluids, either liquids or gases, under pressure. The permeability of a sand depends upon the size and shape of the openings in it and the extent to which these communicate with one another, as well as upon the ratio of their volume to the total volume of the sand. The apparatus employed and the method of procedure used by the authors in conducting the permeability tests have been described in a previous pub1ication.l For the tests described here 1/2-in. cubes were used. They were set in the lower end of a 1-in. union, inserted in a square hole cut in a hard rubber stopper which fitted into the lower end of the union. In the tests with air, volumes were measured with a wet American gas meter of 100 cu. ft. capacity. In those with water, distilled water at room temperature was employed, unless otherwise noted. DescRiption of Sands Tested The tests described in this paper were performed upon 18 samples representing typical oil and gas sands from 7 localities in northwestern Pennsylvania. For purposes of identification, the cores from which the samples came have been designated by capital letters, the sequence of the samples in the cores by numerals, and the individual cubes by small letters. All cubes from the same samples came from adjacent portions parallel to the bedding. Core A of the Bradford sand came from the north central part of the Bradford field, from an area where water-flooding operations have proved highly successful. Core B of the same sand was obtained from the southern part of the field. This core contained a so-called "loose streak," 7.5 ft. thick, in the middle portion of which B2 is a representative sample. The "loose streak" has given trouble in water-flooding but responded favorably to an air-drive, using a pressure of 300 lb. The natural production was increased approximately five times over a period of three years in which the air-drive was in operation. Core C, also of the Brad-

Jan 1, 1931

By H. W. Morse

MANY of our largest copper deposits contain both sulfide and oxidized copper minerals. The large porphyry mines, with a total copper content of from 1.3 to 2.0 per cent., send to their mills ore with an oxide content of from 0.2 to 0.4 per cent. While the recoveries of the sulfide minerals are considered satisfactory, using modern flotation practice, the recovery of the oxi- dized portion of the copper is small; better recoveries of oxidized copper were made before flotation methods were adopted. Beside the ores containing copper mainly as sulfide, with a small amount of oxidized copper,, many of the large porphyry mines have oxide orebodies, in which the propor-tion of non-sulfide minerals is so high that 2 present methods of treatment are ineffi-cient. In some of the well-known ore-bodies in the Miami-Inspiration district the copper occurs about equally in sulfide and oxidized forms; and the mixing of minerals is complete throughout the ore-body. There is no possibility of mining the sulfides and the oxides selectively. At the New Cornelia mine, however, the oxide, and sulfide ores are sharply separated, per-haps by an ancient water level, so that the oxide ore may be mined and treated in a plant built for that purpose, and the under-lying sulfide ore may be left for treatment in another plant. If copper is to be made from an ore having a total content of 1.5 per cent., it must be concentrated or removed from the ore by some. hydrometallurgical method. Flotation is generally successful for the sulfide minerals and flotation after filming with sulfide seems to work in many cases on the pure carbonate minerals. Callow has given an extensive report on the results of "sulfidizing" flotation on the ores of the. Magma mine.1 Where such ?a &apos;method can be applied, it ?may be, the best

Jan 9, 1922

By D. M. Dunbar

LONG before Columbus discovered America the original inhabitants toiled in the copper workings of the Andean Cordillera. Their best diggings appear to have been at Chuquicamata, site of the huge present-day open pit owned by the Chile Exploration Co., subsidiary of Anaconda Copper Mining Co. Located in Antofagasta Province of northern Chile, Chuquicamata is in the Atacama desert, high on the western slope of the Andes at 9500-ft elevation. In the Chuquicamata area the Atacama desert merges into the Cordillera. The climate is extremely arid and precipitation, either in the form of rain or snow, is very infrequent. The temperature varies from 50° to 85°F during the day, and drops to 20° to 40° at night. The Antofagasta and Bolivia Railroad, which connects the Chilean Port of Antofagasta with La Paz, Bolivia, passes within approximately 6 miles of the plant. A branch from the main line to Chuquicamata serves the property for outgoing copper and incoming freight. The distance to Antofagasta by rail is 163 miles. Previous to the Inca conquest, this region was inhabited by the Chuco Indians, a small tribe, descendants of the Aymaras and Quechuas. The Incas, whose capital was located in Cuzco, Peru, gradually extended their empire to the south, reaching at one time to what is now central Chile. It is believed that they built crude primitive furnaces on the banks of the Rio Salado where on a small scale they smelted copper ore from Chuquicamata. At the time of the subsequent Spanish conquest, legend has it that Diego de Almagro, on his return to Cuzco in 1536 after his invasion of Chile, obtained from these furnaces metallic copper for horseshoes. During the period from 1560 to 1879 the high grade veins of the Chuquicamata deposit were worked superficially by the Spaniards and Bolivians. The treaty signed after the war of 1879 recognized the sovereignty of Chile over this territory and Chile, realizing the importance of the district, started to develop it in an orderly manner, although only high grade veins were worked. New Process Is Key Reports on the deposit were brought to the attention of Albert C. Burrage, a Boston lawyer and financier, in 1910. Chuquicamata was described as a huge deposit of ore that was not amenable to the usual treatment by concentrating and smelting since much of the copper occurred as oxides. He had been working on a process for the recovery of copper from sulphide ore which involved a sulphating roast, leaching of the roasted product, and pre-

Jan 1, 1952

By James P. Kimball

THE object of the present memoir is to put on record some practical experiments by the writer in smelting a silicious native magnetite with no other flux than the silicates of its own gangue: This work was undertaken in the spring of 1878 for Messrs. Naylor & Co., of Boston, to whom I am indebted for the privilege of here communicating its results, these having hitherto only been simply announced.* So far as I am aware these are the first instances of the kind in this country that non-calcareous; or rather non-carbonated, magnetites have successfully been used strictly alone as self-fluxing ores in the blast furnace; that is, without the addition of calcareous flux in the form either of limestone, quicklime, calcareous ore, or basic (calcareous). slag. Previous to the spring of 1878, when the Chateaugay magnetic ore was first brought to my notice, its use had been limited to Catalan forges, after "separation" at the ore bed. The blooms and billets made from it in the several forges of Messrs. Weed & Williams, and of Mr. Williams, were well known in the trade as among the best in the market. The Chateaugay ore beds proving of great magnitude, and the ore exceptionally low in phosphoric acid, it commended itself for blast-furnace purposes to Messrs. Naylor & Co., who employed nee to blow-in the charcoal furnace at Pittsford, Vt., on this ore in the spring of 1878., a previous trial of this ore in the same furnace in the fall of 1877 having proved abortive. This was therefore the first time that Chateaugay ore was successfully smelted in a blast furnace, although since well known as a blast-furnace ore possessing superior and exceptional qualities. The Pittsford furnace, although rebuilt in 1844, and subsequently improved by the former owner, the late J. Prichard, is one of the few furnaces of the old type with open breast (Sumpfofen) still active in this country. Its improvements on furnaces of the period, * Bulletin American Iron and Steel Association, XII, 1878, 132, 156.

Jan 1, 1881

By D. Harrington

Efficient ventilation of metal mines consists in having such complete control of air currents that there is always supplied at placcs where men work sufficient moving air to allow working at maximum capacity without injury to health; and in case of underground fire or of surface fire in the vicinity of mine openings, underground air currents may be quickly reversed if desired, or air may be sent into or excluded from any region and fire fumes confined to only part of the mine workings, instead of penetrating practically the entire mine. Health and safety of workers in mines as well as proper safeguarding and operating efficiency of mining properties are so intimately associated with proper ventilation of mines (both coal and metal) that they are inseparable, yet ventilation is only too frequently neglected, especial1y in metal mines. The metalliferous operator, generally not confronted with inflammable gas or explosive dust which so frequently force ventilation of coal mines, usually disregards air supply altogether except such as may be obtained from compressed air; and generally, even when attention is given to metal-mine ventilation, the air currents rarely are found where they are needed, namely, the working places, especially the working faces. After several years&apos; study of miners&apos; consumption, the writer is convinced that long continued breathing of air impregnated with large quantities of any kind of finely divided dust, such as is found in a large number of the working places of our mines, will ultimately produce some respiratory disease, whether it be asthma, bronchitis, or phthisis; and the progress of these diseases is hastened if there are also present high temperatures, high humidities, or harmful gases or if there is present (and allowed to remain to be breathed) large quantities of the finely divided dust when air temperatures are low, hence favorable to maximum performance of work with accompanied maximum breathing into the respiratory passages of the harmful material. It is generally accepted

Jan 1, 1923

By Charles Macdonald

It may seem to be almost unnecessary to occupy the time of the Institute in further consideration of a question which has been so comprehensively treated in papers already on file in our own Transactions and in those of the American Society of Civil Engineers. Unfortunately, however, the results of these concerted efforts have not been materially to increase our stock of Knowledge in the direction sought for; and as the necessity for this information is becoming.more and more apparent as the demand for structural materials increases, it is believed that by continuing the agitation by means of discussions in this and kindred societies, whose members are vitally interested in obtaining reliable data as to the properties of the materials they are called upon to work with, public opinion may be educated up to the importance of exerting such an influence upon the law-makers of the country as will result in the formation of a competent board, with adequate means at its disposal, to carry out this great work in a manner alike acceptable to the makers and users of the materials in question. It may be proper in the first place to glance briefly at what has been attempted thus hr, then to indicate some of the more important lines of needed investigation, and finally to consider reasons why government aid may with propriety be sought for in carrying on the work. At a convention of the Society of Civil Engineers held at Chicago June 5th, 1872, it was, on motion of General William Sooy Smith, resolved, that, " Whereas, American engineers are now mainly dependent upon formula for the calculation of strength of the different form of iron and steel, not based on experiments upon American materials and manufacture; and " Whereas, There differ greatly in many of their ch~racteristics front thoae of foreign production, both in their nature and forma: therefore,

Jan 1, 1882

By Lawrence Veiller, D. Eppelsheimer

D. Eppelsheimer, * Middletown, Ohio.—The housing of employees has so many and so varied aspects that in order to reach even an approximately correct solution it is necessary to have in mind a few fundamental principles; but it is not possible as yet to write these housing principles in the clear and correct form that is possible with many of our natural laws. Manifestly, the problem depends first on the kind of people it is necessary to house. What is suitable for the Southern unattached negro is not suitable for the married skilled American. The influx of colored labor has affected quite a number of what were satisfactorily housed communities. The second important factor is the relative proportion of the number of employees to the total employable population of the community in which the industry is located. The employer of a hundred men in a large city has little responsibility in the matter of housing his employees. If he employs 75 per cent. of the employable population in a community of 27,000, as is the case of the company with which the writer is connected, it means a large responsibility. In the establishment of an entirely new plant in a more or less isolated place, the responsibility becomes greater. As engineers, we design and write the specifications for the machinery to accomplish a definite purpose, and proceed to house it, provide the necessary buildings with their accessories in the way of cranes, or heating systems, or sprinkling systems, as the case may be. There is no reason why the operating force should not be built up in very much the same way: design the organization, write its specifications so that the employment department can secure the proper men, and then house that organization with just as much thought and care as is given the plant. In the plant, the various machines will work along certain definite lines and accomplish certain results; but even if we start with the proper organization it takes considerable time to get that organization working together. One of the most important elements to this end is the proper housing of the organization. A man usually spends more time at home than at work. Proper surroundings and a comfortable, convenient house of good appearance exercise an influence that cannot be denied, and an employee situated in such surroundings is far more inclined to follow the policies of his employer and take an active part in furthering them than one dissatisfied with his home and surroundings, which feeling

Jan 1, 1919

By A. Q. Tool

THE necessity of accurate temperature measurements in the glass-making industries is today being much more widely appreciated than in the past. The introduction of the modern simplified and perfected pyrometric methods in connection with exact regulation of furnace temperatures has caused a marked improvement in the glass product with a quickened rate of production. An example of the processes in which much improvement has been and still can be made is that of annealing or heat-treating the glass. This is one of the most delicate processes in glass manufacture and one that requires a most careful furnace control. The heat treatment is undertaken to decrease the possibility of breakage and, in glass for fine optical instruments, to prevent serious warping of accurately ground and polished surfaces and to make the glass more uniform throughout to the passage of light waves. These objects are accomplished by removing all the harmful stresses that exist in a piece of glass when it has been cooled too quickly or unevenly. Such stresses exist, for example, after it has been pressed, cast, or otherwise worked. Thus the process of annealing consists of heating the glass evenly to the temperature at which it softens just enough to relieve these stresses in a reasonable time and then cooling slowly and uniformly until the glass hardens again. Accordingly, the things that must be investigated and determined in order to anneal glass without loss of time are, the annealing temperature, the time that the glass should be held at this temperature while the stresses relax, and the quickest cooling procedure that will give satisfactory results. After these characteristics of the glass are known the problem is one of pyrometry and temperature control entirely. In cases when it is known that a glass article will be required to withstand some definite type of heat or mechanical shock it is often possible, by a proper heat treatment, to produce such a distribution of the stresses in the glass that it will be enabled to resist these shocks more effectively.

Jan 9, 1919

By Dorsey Hager

DORSEY HAGER, Tulsa, Okla.-I have been asked why the Dexter region is dry. I would like to know myself. I drilled two dry wells on that same anticline which has production to, the east and west and south and north. That same anticline has seven domes that have been drilled and only three have proven productive out of the seven. In other words, you have one well-defined anticline with seven domes along its length, all mappable, all checked carefully, and only three of those seven have produced. Now why the others did not produce, I do not know. L. L. HUTCHISON, Tulsa, Okla.-There is no appreciable difference in the character or structure of the sands? DORSEY HAGER.-NO, I have never .been able to see any appreciable difference in the sands where we got production and Where we did not get it. I will say that the deepest wells we drilled, in the vicinity of Dexter, had no sands at the point where they got the production farther north. I. N. -KNAPP, Ardmore, Pa.-I first went to the Kansas-Oklahoma field in 1895 and occasionally thereafter until 1899, when I began drilling; for oil. I started close to wells that were producing gas and which, when drilling, lead made good oil showings in a sand above the gas. I thought these showings were good enough evidence of an oil pool for me without looking for any anticline and I made a paying development in what&apos; I was afterward told by geologists was probably a synclinal trough. If I remember correctly Dr. Orton&apos;s report on the lola gas pool (about 1898) he distinctly said that he found no evidence of anticlinal structure and concluded from the records of a large number of wells that there, was a terraced structure of the productive gas sands, of which there were no surface indications.

Jan 4, 1917

By Irving Cadoff, Jack Medoff

THE linear thermal expansions of oriented single crystals of zinc were measured in the range from 20" to 416°C using a Leitz HTV optical lever differential dilatometer. The single crystals, supplied by Dr. J. J. Gilman, General Electric Research Laboratory, Schenectady, N.Y., were prepared from 99.999 pct-purity zinc, and were in the form of rods approximately 2 in. long by 0.15 in. in diameter having the following orientations: x = 1.5, 12, 20, 30, 37.5, 49, 60, 73, and 82 deg where x is the angle between the specimen axis and the (0001) plane of the crystal. From the family of expansion vs temperature curves, the instantaneous expansion coefficients were calculated at 100°C intervals, and Fig. 1 shows a plot of these derived coefficients for each orientation. Coefficients were obtained from the raw data using the chord-slope method. The curves in Fig. 1 indicate a positive temperature coefficient for low x, a negative temperature coefficient for high X, and an expansion coefficient invariant with temperature, amounting to about 43 x 106, for a crystal orientation of approximately 52 deg. From the available data, it is possible to arrive at the values for the axial thermal-expansion coef- ficients a, and a, by extrapolating the curve of the expansion coefficient vs orientation to zero and 90 deg orientations. More precise values for a, and a, are obtained if the instantaneous coefficients are plotted against the square of the cosine of the orientation angle, as shown in Fig. 2. The extrapolated terminal points of the best straight line through the data points of such a plot define the axial coefficients at that temperature. The theoretical justification for the linearity of this curve comes from inspection of a rearranged form of the general anisotropic equation for expansion: ax=a, + (a, -a,)cosZx [1I in which a, is the expansion coefficient in the "c" or [0001] direction and a, the expansion coefficient in the "a" or [ll50] direction. From Fig. 2, the axial coefficients at 100°C, for example, were found to be a, = 13.9 x 10&apos;6 and a, = 62.4 x 10"6 per "C. In the same way, the coefficients were determined for 20", 200°, 300°, and 400°C. This data is summarized in Fig. 3. It is of interest to observe the common intersection of the curves in Fig. 3, which seems to bear out the earlier observation, from Fig. 1, of a

Jan 1, 1964

By J. A. Fulton, A. B. Foote

Gold was discovered in the Sierra Nevada by J. W. Marshall on Jan. 2, 1848. The town of Grass Valley soon sprang up and contained several stores in 1849; but the population of the town has always reflected the fluctuations in quartz mining. Gold-bearing quartz was found on Gold Hill in September 1850, and in the next two years most of the quartz-bearing veins in the vicinity were located. At first, the quartz was crushed in mortars with spring poles; the IIuff Co. took out $20,000 in this manner during the winter and spring of 1851. The first mill was put up in January, 1851. In 1866, there were in Grass Valley 248 stamps, crushing 71,420 tons of ore with an average yield of $30 to $35; in Nevada City, there were 142 stamps, crushing 14,200 tons, with an average value of $25. Rut in 1918, only two properties in this region, the Empire and the Korth Star, were producing Since then, there has been a revival of mining in the district and the following properties are being opened up: The Golden Center. Grass Valley Gold Mines Co.. Idaho-Maryland Mines Co., while the Su1tana is kept unmatered and work is going on in a half dozen mall propertics Mining Claims At the first meeting of miners in Grass Valley, Jan. 13. 1851, a plot :30 by 40 ft. was allowed for a claim, the boundaries in all cases being perpendicular. In 1852, the quartz miners in Nevada County deeided that "each prospector shall hereafter be entitled to 100 ft. on a quartz ledge or vein and the discoverer shall be allowed 100 ft. additional. Fach claim shall include all the dips, angles, and variations of the vcin." This rule was in force until replaced by the Federal mining laws of 1872; these allowed quartz claims to be 1500 ft along the vein, with all the dips, spurs, and angles, and to have a width of 600 ft. The holdings of the principal companies consist of these early patented mining claims; standard claims, as authorized by the Act of 1872, both patented and unpatented; agricultural tracts, both patented and

Jan 1, 1927

By F. Hass, N. W. Lord

This paper gives the results of experiments conducted in the metallurgical laboratory of the Ohio State University with the objects of determining: First, the calorific powers of a number of coals in general use in Ohio; and second, how far ordinary analytical methods could be used as a basis for computing these values. Incidentally a test of the performance of the calorimeter was involved. The chemical work has been carried on in the department for some time, so that the whole investigation has extended over three or four years. The Mahler calorimeter was purchased from L. Golaz in Paris, and is practically identical with the one described and figured by Mahler in his monograph "Contribution a l&apos;Etude des Combustibles," from the Bulletin de la Société d&apos; Encouragement pour l&apos;lndustrie Nationale. A figure and description is also given by William Kent in The Mineral Industry for 1892, page 97. There were furnished with the instrument three thermometers covering a range of from 7°.5 C. to 31° C. Thermometer "A" (17°.5 to 31°) was carefully calibrated by reading the ends of a thread of mercury in sixteen positions covering the whole scale, supplementing this by readings of longer threads and deducing the errors of scale by the method published by Prof. Holman in the Technology Quarterly of September, 1887. The maximum error of a single reading was found to be 0°.0042 C. Thermometer "B" (13° to 25°) was compared directly with " A " over the scale common to both, and a variation was found of 0°.0145 C. for 7°.5 (or 0°.002 for l°) of the scale. Thermometer " C" (&apos;7°.5 to 19°.0) was omitted from the cornparison, as it was rarely used, being only required where measurements were made at low temperatures. From the

Jan 1, 1898

By V. F. Hollister, M. Bernstein

The Copaquire porphyry copper deposit lies in an island of pre-Upper Tertiary rocks surrounded by Quaternary and Upper Tertiary formations. The pre-Upper Tertiary appears to be a horst block in a typical basin-range setting. Major right lateral faults have been mapped within the range from Chuquicamata north to Copaquire. All of the major porphyry copper deposits known in the block (e.g., Quebrada Blanca, El Abra, Chuquicamata, and Copaquire) are on or are very close to one of these major right lateral shears. In the Copaquire district, an epizonal igneous complex with diorite, quartz diorite, quartz monzonite, and intrusive dacite (in that intrusive order) invade folded Jurassic shale. Mineralization appears spatially and temporally associated with the quartz monzonite porphyry and dacite. Alteration zoning shows two separate core phyllic (quartz-sericite-pyrite) zones within one large argillic (clay-pyrite) zone. A propylitic (chlorite) zone is peripheral to the argillic zone. No potassic zone has been recognized yet at the surface. The intrusive petrology together with the phyllic, argilic, and propylitic alteration zoning as well as the chalcopyrite-molybdenite ore mineralogy characterize this deposit as being typical of the Lowell and Guilbert model. Copper and molybdenum minerals appear to be most strongly developed in the phyllic zone, in either a breccia or a zone of veinlets and stockwork which trend dominantly northeast, conjugate to the district&apos;s largest fault, the Sulfato fault. The setting is basically similar to that found in some other porphyry copper deposits in this block, in that the ore body is a zone of veinlets which appear to be genetically related to movement on a major north-south trending right lateral fault. The presence of the major fault in each deposit, and the speculative hypothesis that paleo-subduction zone operated at the time of mineralization, suggest the possibility that mineralization took place when a major fault permitted escape to the surface of cal-calkalic magma generated in a subduction zone as proposed by Ericksen. A hypothesis such as that proposed by Ericksen explains the near linearity of porphyry copper deposits in Chile, since the source of calc-alkalic magma would exist at about the same distance from a paleo-trench throughout the length of the paleo-subduction zone.

Jan 1, 1976

By John Furness Park

The mining district is located in the northeasterly part of Nevada, between the Jarbidge River on the west and the East Fork of the Jarbidge on the east. The northern boundary of the district is but a few miles south of the Idaho state line—the gold-bearing area extending from this point south, for 5 or 6 miles. • The Jarbidge Mountains, in which the ore deposits occur, range from 5000 to 11,000 ft. in elevation, the most important mines being situated about 7000 ft. or higher. The town of Jarbidge lies along the Jarbidge River and is reached by stage from Rogerson, Ida., the nearest railroad point. During the summer months, the camp may be entered from the south by way of Deeth, Nev., but no regular transportation facilities are available over this route. History The mineral deposits were not discovered until 1909, when D. A. Bourne, panning along the river bank, found gold in. the gravel at the mouth of a small stream flowing into the Jarbidge. He prospected in the vicinity of this stream, later known as Bourne Gulch, and shortly after located the North Star claims. During the following spring and summer (1910), the camp of Jarbidge grew from nothing to a town of 2000 people and the hills surrounding it were practically all taken up by mining claims. Most of the work done during the first year or two consisted of trenching and open-cut prospecting. Tunneling was started on a number of claims and many veins were uncovered. Mills were built and operated on a few properties, notably the Pavlak and the North Star. These ran only a few months, however, when they were closed down because of extraction and financial difficulties. A period of development followed in which the majority of the present producing mines were opened. The Elkoro Mines Co. acquired a number of claims in 1915 and started work on the present mill in 1917. Since that time other properties have been taken over until this company is by far the largest operator in the district. Only one other company is now actively engaged in mining, the Bluster Mining & Milling Co., which has

Jan 1, 1925

By R. D. Reiswig

An increasing amount of high-temperature metall~?~gical research is carried out in resistively heated tube furnaces in which a bare specimen is suspended by a fine wire at the midpoint of the tube. It is shown that the assumption of near-blackbody conditions on the surface of the sample may give rise to errors in optical pyrometry of 50°C or more. A number of papers published in the metallurgical literature in recent years have described the use of high-temperature tube furnaces for heat treatments, melting-point determinations, and other work. Typically, the tube is of a refractory metal with open ends, is heated by the passage of an electric current, and has concentric cylindrical radiation shields outside it. In at least one of these,&apos; the specimen is contained within a crucible having a small hole in its lid through which optical-pyrometer measurements are made under essentially blackbody conditions. In another design,* the specimen is inside a muffle which is concentric with the heater tube and which contains a number of washerlike longitudinal radi- ation shields to reduce axial temperature gradients and to give conditions near the specimen closer to those of a black cavity. Yet another design3 employs a wire specimen coaxial with the heater tube. Blackbody conditions are simulated by passing current from a separate supply through the wire until it "disappears" against the background (the inside of the heater tube) as seen through a radial spy hole in the tube. Good agreement with known melting points is achieved when an optical pyrometer is used under such disappearance conditions as the melting point is approached. That this latter method works so well is due, evidently, to considerations such as those mentioned by Dike4 and others.5-8 A more common method than the above, however, has been the suspension of an uncovered specimen by a fine wire in a resistively heated tube with open ends. A radial spy hole about midway between the ends of the tube permits optical-pyrometer observations on the specimen, the inside of the tube, or both. So observed, the specimen typically appears to differ but little in brightness temperature from the inside of the tube. According to De vos9 the radiation from such a spy hole in an empty tube of reasonable 1ength:diameter ratio (e.g., 10 or greater) should be essentially blackbody radiation. For these reasons, apparently, descriptions of work carried out in such furnaces usually include a statement to the effect that conditions surrounding

Jan 1, 1964