Search Documents

By G. J. Wilson

Review of difficulties experienced in drilling directional wells in the offshore Grand Isle Block 43 field showed most failures of drill pipe, drill collars and casing to have been associated with excessive dog-legs. Alleviation of difficulties was approached by synthesizing theoretical and practical concepts in a planned dog-leg control program. Preventive measures necessary to control dog-leg severity and corrective measures used to reduce unacceptable doglegs are discussed. When other measures fail, deliberative measures as outlined can be employed after the probable cumulative fatigue damage to be sustained by the drill pipe has been determined. Results of a program successful in virtually eliminating problems stemming from excessive dog-legs indicate that control of dog-leg severity in directional wells is feasible and will cause no decrease in the over-all drilling rate. INTRODUCTION Prompted by an increasing frequency of drill pipe, drill collar and casing failures, a study of 50 directional wells representing 592,000 ft of hole, including 444,000 ft of deviated hole, drilled in the offshore Grand Isle Block 43 field was conducted in early 1965. A number of drill pipe washouts and six keyseating problems were recorded and a detailed review was made of 16 failures which had required fishing effort in 10 of the 50 directional wells drilled prior to June, 1965. These problem wells are exemplified by Wells G and F for which pertinent data are shown in Figs. 1 and 2. Data pertaining to all of the 16 failures are summarized in Table 1. Inspection of these data shows most of the problems to have been associated with dog-legs in excess of theoretical limits suggested by Lubinski' and excessive dog-legging is indicated to have been concomitant with whipstocking in several of the problem wells. Results of the investigation agreed with those reported by Schenck2 who had concluded that problems could be expected when dog-leg severity exceeded limits proposed by Lubinski. Since Schenck had demonstrated the desirability and feasibility of drilling directional wells without excessive dog-legging, a dog-leg control program was established in June, 1965 for wells drilled in the Grand Isle Block 43 field. This paper reviews the methods by which theoretical and practical concepts were synthesized to develop a program of preventive, corrective and deliberative measures which virtually eliminated problems stemming from excessive dog-legs in directional wells. Dog-legs of a magnitude causing no damage are referred to as permissible +1CONTINENTAL OIL CO. HARVEY, LA.

By William S. McAleer

Two major trends in the coal industry today focus attention on the need for heat-drying equipment of a simpler, more flexible and less expensive type than has been considered standard equipment for drying coal. These trends are: I. The tremendous growth in the use of mechanical equipment to load coal both in underground mining and strip mining, which necessitates efficient mechanical cleaning of the fine as well as the coarse coal and thus means a growing tonnage of washed fine coal? with its attendant moisture problems. 2. The growing consumer demand for the smaller sizes for use as domestic stoker coal, with increasingly rigid specifications covering size, ash, and moisture analyses. ACCEPTED PRACTICE In the past, when, for example, 4 in. too coal has been washed, there was little trouble in producing a washed product 4 to o with a satisfactory resultant moisture. The 4 to 3/8-in. could be taken from dewatering screens at a surface moisture ranging from 2.5 to 3.5 per cent, depending upon the size consist. The 3/8-in. to o coal was generally dewatered satisfactorily with centrifugal driers, to final surface moistures from 5.5 to 8 per cent, again depending upon size consist. The centrifugal type of drier has definitely proved itself to be the most economical type of machine to handle coal approximately 3/8 in. to o as recovered by dewatering screens or drainage elevators with 15 to 25 per cent surface moisture and turn out a product with moistures as stated above. Sometimes such moistures (5.5 to 8.0 per cent) in the product are satisfactory. If not, an ultimate moisture, lower than 3 per cent, is seldom required and the centrifugal drier removes 70 to 85 per cent of the total moisture to be removed. In certain districts there has been a growing tendency to circumvent the use of centrifugals or other types of driers, by dewatering over screens of the wedge wire type and wasting all the finer sizes. Sometimes all the minus 28-mesh has been wasted and often the size wasted has been as large as 1/8-in. By wasting these finer sizes, a lower moisture can be obtained in the finished product, but taking into account the cost of the tonnage so lost, plus the added cost of ultimately disposing of this wasted tonnage, often the cost will be greater than the cost of heat-drying in a modern plant, which makes possible the recovery of all the tonnage. Moreover, with the moisture standards for domestic stoker equipment even these wasteful approaches to its solution do not solve the problem and there remains only the alternative of heat-drying. HEAT-DRYING Until about four years ago, heat-drying of coal at the preparation plants was confined chiefly to drying the fine sizes (approximately 3/8 in. to 0). Occasional

Jan 1, 1941

By R. M. Raymond

RECENTLY one of the Welsh coal companies, which has an excellent plant of up-to-date ma-chinery both on the surface and underground, operated under modern methods, sent one of its engi-neers to the United States to study actual operations in the mines. He visited several of the most important and best conducted collieries, went back, and reported that the greatest difference between operations in England and in the United States was. the closer con-tact between management and workmen. By manage-ment he meant management all the way through; close cooperation between office management, superintend-ents, foremen, shift-bosses, etc., and the workmen. A visit to some of the coal mines in that country by the writer made this fact rather impressive. The feel-ing on this side of the water that the methods in use in the coal mines in England are not up-to-date was found in many cases to be quite erroneous. Many mines, particularly those with very thin beds, in which profitable operations are doubtful under the best con-ditions, have necessarily had to adhere to old methods instead of making mechanical improvements. The Powell-Duffryn mines, in the center of the South Wales district, are certainly operating successfully, and have planned their business excellently. Sufficient areas of contiguous land have been leased for extended opera-tions. Mine plants are laid out in the valley, for work-ings on both sides, on a reasonable tonnage of 1500 to 3000 tons to each operation. The beds are from 30 to 48 in. thickness, and a 3-ft. seam is considered an ex-cellent thickness of coal; in fact, the miners prefer to work on the thinner beds rather than the thick ones, where they consider it more difficult to control the backs. This company is making use of its fine coal for produc-ing electric power, which is distributed to its own operations, and for use in the communities adjoining. For this purpose methods of cleaning the fine coal are being put into use. Compressed air is generated at the central power plant and is transmitted over long dis-tances to various mines in each valley. A byproduct coke plant uses more of the fine coal and gives further returns from non-commercial coal. The long-wall system applied in sections of limited size is popular in working the small seams, and me-chanical cutting is used, also handling either by shaking chutes or belt conveyors, or a combination of both. In some mines mechanical cutting is not necessary. The backs are so handled that in the softer or somewhat crushed seams hand cutting can be carried on effec-tively.

Jan 10, 1927

By Paul Billingsley

The Asientos-Tepezala district is in the north of the State of Aguasca-lientes, about 30 miles north of the city of Aguascalientes, the capital. The district is reached by a standard-gage railway on the west side through the junction, Rincon de Romos, which is on the main line of the National Railways of Mexico from El Paso to Aguscalientes. The terminal is Tepezala. On the east side a narrow gage connects Asientos with the junction, San Gil, on the main line, Asientos to San Luis Potosi. Tepezala on the west side of the Asientos hills is about 2 miles from Asientos on the east side. The area between the two mining centers is separated by a low subdued divide which forms the central part of the hills. The district is in a group of isolated hills surrounded by characteristic bolsón plains. The hills rise above the surrounding plains about 6500 to 10,000 ft.; the highest peak is Alta Mira. The two mining districts lie somewhat upon the flanks of the hills at about the same elevation, 7200 ft. The district is an old one and has been known since early in the 17th Century when the mines were worked by the Franciscan Monks. Their mining operations, which were limited to the oxidized ore above the water level, consisted chiefly in extracting silver from the Santa Francisca vein. To judge from the old workings and the remains of surface plant, the operations were on a large scale. By modern mining operations since about 1900, the various mines of the district have been one of the principal sourees of ore for the smelter located at Aguascalientes. Topography The topographic features of the Asientos hills are largely controlled by the character of the underlying rocks. During the Tertiary period, the entire group of hills was probably covered by extrusive volcanic material in the form of cones and lava flows. The central part of these have since been carried away by erosion, so that remnants have been left along the borders of the hills. These remnants form rather conspicuous peaks,

Jan 1, 1927

By William Loblowitz

A simplified system of flotation testing has been developed recently at the Bureau of Mineral Research of Rutgers University. The technique involves the known principle of skin flotation and can be used with minute quantities of sample and reagents in a beaker. A vessel containing the conditioned sample with added water and flotation reagents is held inclined and rotated slowly. Water-repellent particles come in contact with air and float on the surface of the liquid, while wettable particles are submerged. The float is poured off and filtered whereas the nonfloat remains in the beaker. The filtrate may be returned to repeat the process. This procedure can be made quantitative. Separations are obtained and are remarkably complete and repeatable. The effect of different reagents, optimum quantities, pH and other variables can be determined in a fraction of the time required for conventional testing. However, the method gives no information on the effect of frothers and the quality of froth to be expected in a cell, and it is not practical for particles finer than 200-mesh. Unlike other preliminary tests, separate float and nonfloat products are obtained, and their contents can be determined quantitatively by chemical analysis or grain counts. After the optimum reagent combination has been determined, the effect of fines and frothing may be verified in the conventional flotation cell. On the other hand, agglomeration-tabling can be directly duplicated from beaker tests. Procedure: Five to ten grams of sample are weighed into a 100-ml beaker. Flotation reagents and a small initial quantity of water are stirred together; additional water is then added to produce the proper water-solids ratio. The beaker is then tilted to 45" and rotated slowly. After three to five rotations, liquid and float are poured off and filtered; the filtrate may be recycled until the separation is completed. One test generally requires less than 10 min. Reagent concentration and pH remain quite constant because of the recycling of the filtrate. Two to four tests may be made simultaneously, and the effect of varied conditions may be observed by comparison. Considerable time is saved in preparation and handling since small quantities of sample suffice for a series of systematic tests. Repeatability One test was repeated four times under constant conditions. The sample used was a quartz sand containing approximately 24 pct feldspar and some clay aggregates. The +28-mesh grains had been screened out, and most of those finer than 100-mesh had been removed by hydraulic classification. The results are presented in Table I. For comparison, 500 g of the sample were separated by agglomeration-tabling using the same reagent combination and quantities as given in Table I. The weight percent float was 18.3 pct, composed almost entirely of feldspar and with only traces of quartz. Most of the remaining feldspar was recovered in a middling product with 2.2 pct by weight.

Jan 1, 1952

By Ernest Kirkendall

The amount of research done in the last fen years on the subject of diffusion in solid metals is significant of the importance of this problem. To review the literature dealing with diffusion is unnecessary here. Deschl in 1912 reviewed the work that had been done on diffusion in solids and gave a bibliography of the literature published before that time. Mehl's paper in 19362 is an excellent review of diffusion in metals and contains a large bibliography. Of importance also for it? review and bibliography is an article by 14. I. Krynitsky.~ While considerable material lias appeared in the literature on diffusion in brass, the amount of information is not great compared to that pertaining to some of the other alloys. Most of the information published is of a qualitative nature; that which is quantitative varies considerably. Thus the quantitative determination of the rates of diffusion of copper and zinc in alpha brass by a new method appeared worth while. In the present investigation the rate of diffusion of zinc in approximately the same composition alpha brass has been determined :it three temperatures. Procedure The method used consisted of plating copper on a beta brass, heating it, to allow diffusion to take place, and measuring the concentration of copper by determining the lattice constant of the alloy. This method is unique in that it uses a beta brass of such a composition that at the tem perature at which diffusion takes place the beta brass is saturated wit11 copper. Thus, while the beta brass supplies thc zinc, no diffusion takes

Jan 1, 1939

By John E. Conley, John A. Ruppert

LIGHTWEIGHT aggregates have been in use for many years in the United States but are now receiving more and more attention by manufacturers and users of concrete shapes. These shapes comprise building blocks, special forms, such as door sills, lintels, floor slabs, and beams. Lightweight aggregate also is adapted for monolithic construction. The increased building activity since termination of the war, together with the widespread shortage of cinders resulting from a general trend toward the use of oil and pulverized-coal fuels, has aggravated the situation. In some localities? new producers of lightweight aggregates have been stimulated to increased efforts to supply the demand. In addition, various estab- lishments of the United States Government have recently given attention to this problem. The National Bureau of Standards, in the Commerce Department, and the Bureau of Reclamation, in the Interior Department, have completed a series of tests on concretes made from some of the available commercial aggregates in order to evaluate their qualities. The tests have been made to focus attention on the desirable properties of good aggregates. This work was done at the request of the Technical Office of the National Housing Agency and Housing and Home Finance Agency. Some time previously, the former office had conducted a survey of the locations where lightweight aggregates are produced.' A study of this information discloses that the producing centers are widespread and that certain areas, notably the region east of the Mississippi River and especially the southeastern states in the sections along the Atlantic Coast, have only a limited number of such plants. The situation has been alleviated to some extent with new plants having been erected near Richmond, Va., and Lansford, Pa. Experiment Stations of the Federal Bureau of Mines at Tuscaloosa, Ala., Norris, Tenn., and College Park, Md., have investigated types and sources of potential raw materials such as clays, shales, and slates, as well as methods and procedures for utilizing these materials for their conversion into aggregates, and have published the data as a Bureau of Mines report.' Structural Uses of Lightweight Aggregates: Production of masonry blocks in the United States has averaged close to a billion units a year for the past three years, and of these it is estimated that more than 40 pct consisted of the lightweight type. It is anticipated that the future will witness an increase in this percentage in view of the superior insulating properties, decrease in dead weight, and ease of handling, transporting, and laying units of this type. Lightweight aggregates are used extensively in multistoried buildings in which the weight of the walls and floors is carried by a structural steel framework. The substitution of a lightweight concrete for normal concrete in a building of this type has brought about in many instances some or all of the following advantages:

Jan 1, 1951

By Ernest N. Patty, Sherwin F. Kelly

The present case history deals with the examination of an almost forgotten nickel prospect, near Winesap, Chelan County, Washington. Although the final results yielded no ore body of commercial importance, the integration of surface and underground exploration, geophysical survey and diamond drilling endow the story with interest. The program is significant because it is illustrative of how the most disappointing expenditures in mining exploration, the "not-finding" costs, could have been reduced had geophysical methods been applied at an appropriate stage in the prospecting work. The Chelan nickel deposit was discovered about 1900, on a sage-brush-covered hillside with a southerly slope, adjacent to Winesap Canyon; the paved highway now extending from Wenatchee northward, up the Columbia River and into Okanogan Valley, is only a mile away. After the deposit was found, three short prospect tunnels were driven into it, and the prospect then remained dormant for 40 years. No. x tunnel was 80 ft. long, running north into the hillside. For the first 35 ft. this adit exposed a typical, iron-stained gossan with streaks and stains of malachite, and small seams of water-soluble nickel sulphate. Beyond this, it encountered a relatively fresh peridotite, well mineralized with blebs of pentlandite. Systematic sampling yielded an average assay of 1.5 per cent nickel and 0.3 per cent copper. Down the hillside to the south and 35 ft. lower in elevation, No. 2 tunnel was driven under No. I and in the same direction, traversing 50 ft. of gneiss before it reached the peridotite. At this point the latter formation showed only scattered blebs of sulphides, not of commercial grade. To the west, on the same contour line as No. I tunnel, and 800 ft. around the hillside from it, No. 3 tunnel was driven 50 ft. into the hill to explore a strong gossan outcrop that assayed 0.5 per cent nickel (Fig. I). From the geological exposures on the hillside and in the tunnels, it appears that the main mass of the hill is formed of an ancient and altered gneiss complex. Into this, a sill-like injection of amphibolite (altered peridotite) was intruded, which, at least in some places, contains commercial quantities of nickel sulphide. Its structure is obscure, but it appears to dip into the hill at an angle of about 15°. In the vicinity of No. 3 tunnel a large dike of quartz diorite cuts the peridotite or amphibolite; about 140 ft. north of the portal of the tunnel, a dike of andesite 00 ft. wide cuts boldly up the hillside to break the continuity of the peridotite in that direction. The geological evidence available was not adequate to decide whether the peridotite forms a continuous sill, or occurs as isolated bodies in the gneiss. Not all of this peridotite carries commercial amounts of pentlandite, but if the mineral-

Jan 1, 1946

By Arthur Notman

(San Francisco Meeting, September, 1915) SACRAMENTO HILL is a mass of granite porphyry intruded along a fault between Paleozoic sediments and pre-Cambrian schists in the Bisbee district, Cochise County, Arizona. The intrusion invaded both walls of the fault to a large extent, and the accompanying extensive mineralization of the Paleozoic limestones is the locus of the great high-grade copper orebodies of the Bisbee mines. Prior to 1909, although the presence of ore in the mass of the hill itself had long been suspected, systematic exploration had not been attempted. A few shallow pits on the surface here and there had disclosed some chalcocite with associated carbonates as stringers in a mass of strongly brecciated, silicified, and iron-stained porphyry. The workings in the surrounding limestones had penetrated the porphyry in a dozen or so places for some distance from the contact but had disclosed no ore. However, the rock had been largely altered to quartz and sericite and very thoroughly impregnated with pyrite and traces of the copper sulphides. A close geological study of the conditions, both surface and underground, strengthened these suspicions, and plans for prospecting the hill were made in 1909. Reference to the accompanying illustrations, Figs. 1 and 2, will give an idea of the general appearance of the surface. The mineralization is more intense in two main zones, one at the west end and the other at the east end of the hill. The outcrop of the hill is elliptical and approximately 3,000 ft. long by 1,400 ft. wide. The Sacramento shaft, which is the main hoisting shaft of the mine and situated at the east end of the hill, as shown by the accompanying map (Fig. 3), offered a convenient base for prospecting that end of the hill, while the workings from the Holbrook shaft offered a similar opportunity at the west end. The choice of level for the first work was determined by analogy with the most favorable depth for enrichment below surface observed in the other disseminated deposits of the Southwest.

Jan 8, 1915

By C. E. Violet, R. J. Borg, E. M. Howard

The miscibility gap in the Au-Ni system has been determined by Mossbauer spectroscopy, with used as a probe. The phase boundaries were determined from the compositional dependence of both the isomer shift and Curie temperature. X-ray diffraction measurements were also used to confirm the Mossbauer results. 1 HE purpose of this research is to demonstrate the application of Mbssbauer spectroscopy to the determination of phase boundaries and to redetermine the miscibility gap by an independent and novel technique. The techniques evolved in this study are readily applicable to other polyphase systems and are generally as quick and accurate as the more conventional methods, e.g., metallography, X-ray diffraction, thermal analysis, and so forth. To be sure, not all polyphase systems will lend themselves favorably to Mijssbauer investigations, but this is a problem met in the use of conventional methods as well. The Mbssbauer spectrum responds to a different set of physical parameters, and consequently provides an entirely independent method of analysis. It is especially useful if the system has either a ferromagnetic or an antiferromagnetic transition. The Au-Ni system was selected because alloys containing more than -60 at. pct Ni become magnetically ordered at low temperatures; also the miscibility gap is quite well established (see Ref. 7 for a compilation of pertinent references, also Fig. 11, and thus provides a reliable test of this novel procedure. As Fe is the most commonly used Mijssbauer isotope, there exists a wealth of information concerning its behavior in iron-containing alloys and compounds. However, as yet there have been relatively few experiments using it as a probe to investigate nonferrous systems. By choosing a nonferrous alloy system, we are able to demonstrate that its use is not restricted to systems containing iron as one of the major constituents. Wertheim and ~ernick' have used the same method to investigate Cu-Ni, and demonstrated that one can obtain a systematic variation in the isomer shift and magnetic hyperfine field. However, we believe this to be the first time these techniques have been used to establish phase boundaries. Two hyperfine interactions were measured and used to determine the phase boundaries, viz., the magnetic hyperfine splitting and the isomer shift which in this alloy system are both strong functions of composition. Calibration curves were established based upon single-phase solid solutions obtained by quenching from temperatures well above the maximum of the miscibility gap, see Fig. 1. Solid solutions containing 25, 50, 65, 75, 85, 92, and 96 pct Ni as well as pure nickel were used in the calibration procedure. Fig. 2 shows the Curie temperature, TC, and the isomer shift, v,, as determined from the Mbssbauer spectra, and variation in lattice parameter as determined by X-ray diffraction, as functions of composition. The compositions of the two-phase systems quenched from temperatures within the miscibility gap are obtained by comparing their respective values of TC and v0 with the calibration data. I) EXPERIMENTAL Mbssbauer sources were made by fusing the component metals in a tungsten arc melter, which has a water-cooled copper hearth. Both nickel and gold were 99.999 pct pure, and the melting was done in an atmosphere of purified argon. The alloys were rolled, diced,

Jan 1, 1969

By G. Sachs, Jr. Brown W. F., Ebert L. J.

It is a generally recognized fact that a steel quenched from the austenitic range and tempered to yield a structure composed of tempered martensite becomes increasingly more ductile with increasing tempering temperature. However, the conventional tensile test fails to yield any value that is sensitive to differences in behavior on tempering among the various low-alloy steels or among different heats of a particular steel. The notched impact bending test, on the other hand, has been recognized for a considerable length of time as capable of revealing differences in impact properties among various steels tempered to 'the same strength level (i.e., the same tensile strength in a conventional tensile test). However, this test is very complex and its significance has not been clarified up to the present time. Of its three characteristic features—the high speed, the notch, and the bending—the notch has been found by Davidenkov2 to be the most potent embrittling factor. Recent investigations on low-alloy steels have shown static notch-bar tensile tests to be more lucid and to evaluate the metal properties in much the same manner as impact tests. In an attempt to analyze the fundamental nature of this test, it was found possible to separate the effects of the two basic characteristics of the stress pattern introduced by the presence of a circumferential notch, the stress state and the high initial stress concentration at the notch bottom. The major conclusions drawn from these previous investigations were as follows: I. The magnitude of the triaxiality at fracture depends primarily on the initial notch depth. Its effect is a great reduction in the average ductility (contraction in area at fracture in the notched section) as compared with that observed in uniaxial tension. This triaxial stress state occurs at a point in the interior of the notch specimen. It determines the notch ductility if the notch is mild and/or the metal possesses a considerable ductility. On the contrary, brittle specimens probably fracture on the metal surface (at the notch bottom) at which point biaxial stress state is present. This biaxiality also considerably reduces the ductility of the metal. For small notch ductilities the notch strength and the notch ductility become very sensitive to embrittling factors. This is contrary to the behavior. of the ductility values derived from a conventional tensile test, which are comparatively insensitive.

Jan 1, 1947

By E. N. Cameron, H. M. Bannerman

During the years 1942-1934, about 125 New England deposits were mined for sheet and punch mica, and many others were briefly prospected. During this period the Geological Survey, United States Department of the Interior, carried on detailcd studies of the deposits and the pegmatite bodies that contain them. The primary purpose of the studies was to provide geological information that would contribute toward efficient mine development and operation. The studies were aimed directly at practical production problems. Detailed maps showing the structure of the deposits were prepared, and geological findings were closely correlated with data on specific yields and costs of mining and processing. The result is information that permits a reasonably accurate appraisal of the mica deposits of New England and the mining industry that they support. At a time when the future of the industry is in doubt, it seems desirable to submit this appraisal for consideration. Domestic mica deposits supply only a small fraction of the country's needs in normal times? for only the richest domestic deposits can compete with the low-cost mines of India and Brazil. However, the possibility that this country may be cut off from its supplies in time of war gives domestic deposits an importance much greater than their peacetime production would imply. New England supplied about 22 per cent of domestic output in 1943 and 1944, the peak years of wartime production. Its actual contribution to the war effort was greater, for the proportion of sheet mica of high quality in the New England product is higher than the average for domestic mica. The data analyzed below were collected for the Geological Survey by D. M. Larra-bee, A. H. McNair, J. J. Page, V. E. Shai-nin, G. W. Stewart, and the co-authors of this paper. The cooperation of officials of Colonial Mica Corporation and of mine operators and owners in furnishing information is gratefully acknowledged. D. M. Larrabee, A. H. McNair, and V. E. Shainin have made various suggestions based on critical reading of the manuscript. Analysis oF Warrtime Operations In considering the data presented in this report, it must be remembered that the scale of mica operations is very small compared with that of many other mining industries. The typical New England mica mine of 1943 and 1944 was worked by a crew of five or six men. Equipment was varied but on the whole extremely simple. The first stage of operation at a deposit was normally opencut mining. Drilling was done mostly with jackhammers powered by portable compressors driven by gasoline engines. Muck was shoveled by hand into buckets with a capacity of 45 to 35 ton and commonly hoisted by derrick to a dump adjacent to the cut. As operations were carried to greater depth, and the tram sition to underground mining was made, these methods were modified to a degree depending largely on the attitude of the deposit mined. At steeply dipping deposits,

Jan 1, 1948

By W. T. Bishop, G. A. Crowe

While the literature in the United States on general polarographic technique is extensive, very little appears to be directly applicable to the analysis of flotation tailings. For this reason, it seemed worth while to present a few polarographic methods of ore analysis that have been in constant use in the laboratories of the Hercules Experiment Station for the past few years. At the time of our initial investigation of the polarographic method, there was little or no mention of its specific application to flotation tailings. It was therefore necessary for us to establish suitable conditions for the analysis of our flotation tailings and to consider possible interfering constituents. The polarograph, or dropping mercury electrode, method was discovered in 1925 by J. Heyrovsky and M. Shikata,1 of the Charles University, Prague. This method has since received extensive development and the literature contains many articles on the use of the polarograph for the quantitative determination of metals as well as anions, oxygen in solution, and reducible organic compounds. Kolthoff and Lingane,² by the publication of their book, "Polarography," in 1941 did much to advance the knowledge and use of the polarograph. In chapter 25 of that book, methods for the polarographic analysis of brass, steel and iron products, alloys, and zinc ore are given. Aluminum,³ cadmium,³,4 cobalt,4 cop-per,³-9 gold,10 iron,3,11 lead,³,l2,l³ molybdenum,14 nickel,4,8,9 tin," and zinc³,4,5,7 in ores have been analyzed by the polarograph. However, most of the work on tailing samples has been published in Russian journals and translations are not yet readily available. In this paper we will describe the method that was developed and used in our laboratory for the determination of copper, zinc, and lead in flotation tailings. Principle OF the Method The polarograph is an instrument for applying a potential to a mercury pool and a dropping mercury electrode separated by a solution, and for measuring the resultant electrical current. The procedure is essentially a small-scale electrolysis, in which the voltage required to reduce or oxidize the material identifies it qualitatively and the current measures the concentration quantitatively. Different constituents in a sample may often be determined simultaneously provided they reduce at sufficiently different voltages. An example is the determination of copper and zinc in the same solution. The reduction potentials are quite far apart, as shown in Fig. I. The polarographic method is particularly useful in the range of concentration between those normally determined by spectographic and chemical methods. In

Jan 1, 1947

By Georges Caraghiaur

INTRODUCTION A small, independent mining enterprise (SIME) is an independently owned and operated business concern engaged primarily in mineral development, from the exploration to the production stage. A SIME may or may not be listed on stock exchanges. By definition, a SIME is not dominant in its field and has no long-term financial backing. As such, it is not a major producer of minerals, nor is it a petroleum company, a government organization or a subsidiary of such organizations. The survival and growth of a SIME is most often controlled by an independently minded entrepreneur, who not only conceives and carries out new projects, but is materially affected by the success or failure of these projects. Usually, a SIME does not have a large or constant cash flow. Such a lack of long-term financial backing forces the SIME to meet the challenge of finding capital for its activities on a step-by-step basis. Its survival strategy is thus based on finding funds at the right time, of the right type and in the right quantities. The purpose of this paper is to show that the type of venture in which a SIME is involved affects the difficulty of raising new capital and the choice of possible sources of funds. The Small, Independent Mining Enterprise The SIME, also called small miner, junior mining company, speculative mining company, and pennystock mining company, is not a figment of the imagination of financial speculators. In Canada, there are more than 1,800 small mineral enterprises which spend on the average less than $1,000,000 per year on activity which is directed at bringing forth new mineral supply. In the United States, 64 percent of the non-fuel mining operations are conducted by nine or fewer men, and the coal industry is characterized by several thousand smaller independent producers, still predominantly family-owned or controlled. In Chile, 80 percent of the mines can be classified as small mines. In the Philipines, approximately 60 percent of metal mining operations are classified as small mines. The SIME is actively engaged in mining all over the world, and very much so in the Pacific Rim. The Mineral Supply Process The whole process of bringing forth new mineral supply involves a dynamic sequence of activities, ranging from the initial exploration for a mineral occurrence to the production of a marketable product. A typical sequence is outlined in Figure 1. At the grass-roots exploration stage, a series of geological, geophysical and geochemical tests is aimed at locating a mineral occurrence. Especially in the early phases of such activities, the uncertainty (risk) surrounding a venture is high, since only general geological information exists on which to base a judgement of the economic viability of the venture. Such risk is attractive to few investors.

Jan 1, 1982

By J. O. Scott

Transient pressure behavior of wells intersected by a single vertical fracture has been examined by means of a heat pow analogy. Results are correlated in terms of dimensionless pressure change and dimensionless transient time. The resulting curves are found to lie between the dimensionless curves for a cylindrical well and a line source when effective well radius is expressed as one-fourth of the total fracture length. Results are also shown for various degrees of afterflow. Use of the curves provides a means of determining reservoir permeability, wellbore radius, and thereby fracture length, even when the final slope of the transient curve is not obtained. Superposition of curves may be used to confirm existence of vertical fractures in the reservoir adjacent to the well or to indicate a damaged zone on the fracture face. INTRODUCTION Hydraulic fracturing has become a standard well completion practice for the purpose of increasing flow. Results are normally gauged in terms of some sort of "stabilized" flow rate established before and after the treatment. This procedure may be misleading because pressures in or around the well do not become "stabilized" during the test period. Transient pressure tests on fractured wells can overcome the objections to stabilized flow tests by indicating when a stable pressure gradient is reached. In addition, the transient pressure tests can be used to determine formation flow capacity and effective wellbore radius. The effective wellbore radius may be used as a measure of the success of the fracturing operation. The slope and position of the transient pressure-log time curve may be used to determine the flow capacity and wellbore size after sufficient lapse of time so that the pressure gradient in the vicinity of the fractures becomes constant. However, in tight reservoirs or in short tests this condition may not be reached. Presence of the fractures in tight reservoirs may cause a constantly increasing slope to the transient pressure curve. If this slope is picked too soon, formation flow capacity will appear high and the fracture size will appear too small. This paper is intended to clarify the early transient behavior of vertically fractured wells. It shows how formation flow capacity and wellbore size can be determined even though the maximum slope of the transient pressure curve is not obtained during the test. Development of the techniques of transient pressure analysis for wells has been summarized by Perrine.' He reviews the various definitions of wellbore effects such as skin effect, productivity ratio, damage factor and condition ratio. In the present paper, use of these terms is avoided by defining an effective wellbore size. For the fractured well this effective wellbore size is larger than the actual wellbore. Assumptions made are constant flow rate at the well, constant fluid compressibility, constant fluid mobility and uniform porosity and formation thickness. From the basic differential equations of flow, two different solutions may be obtained. The first, the line source solution, is commonly used in transient pressure analysis.' It expresses the change in pressure at any radius due to withdrawal or injection of fluid at the line source from an infinite reservoir at uniform initial pressure. This equation, in oil field units: is

By Ernest Kirkendall

The amount of research done in the last fen years on the subject of diffusion in solid metals is significant of the importance of this problem. To review the literature dealing with diffusion is unnecessary here. Deschl in 1912 reviewed the work that had been done on diffusion in solids and gave a bibliography of the literature published before that time. Mehl's paper in 19362 is an excellent review of diffusion in metals and contains a large bibliography. Of importance also for it? review and bibliography is an article by 14. I. Krynitsky.~ While considerable material lias appeared in the literature on diffusion in brass, the amount of information is not great compared to that pertaining to some of the other alloys. Most of the information published is of a qualitative nature; that which is quantitative varies considerably. Thus the quantitative determination of the rates of diffusion of copper and zinc in alpha brass by a new method appeared worth while. In the present investigation the rate of diffusion of zinc in approximately the same composition alpha brass has been determined :it three temperatures. Procedure The method used consisted of plating copper on a beta brass, heating it, to allow diffusion to take place, and measuring the concentration of copper by determining the lattice constant of the alloy. This method is unique in that it uses a beta brass of such a composition that at the tem perature at which diffusion takes place the beta brass is saturated wit11 copper. Thus, while the beta brass supplies thc zinc, no diffusion takes

Jan 1, 1939

By Ebert L. J., G. Sachs, Jr. Brown W. F.

It is a generally recognized fact that a steel quenched from the austenitic range and tempered to yield a structure composed of tempered martensite becomes increasingly more ductile with increasing tempering temperature. However, the conventional tensile test fails to yield any value that is sensitive to differences in behavior on tempering among the various low-alloy steels or among different heats of a particular steel. The notched impact bending test, on the other hand, has been recognized for a considerable length of time as capable of revealing differences in impact properties among various steels tempered to 'the same strength level (i.e., the same tensile strength in a conventional tensile test). However, this test is very complex and its significance has not been clarified up to the present time. Of its three characteristic features—the high speed, the notch, and the bending—the notch has been found by Davidenkov2 to be the most potent embrittling factor. Recent investigations on low-alloy steels have shown static notch-bar tensile tests to be more lucid and to evaluate the metal properties in much the same manner as impact tests. In an attempt to analyze the fundamental nature of this test, it was found possible to separate the effects of the two basic characteristics of the stress pattern introduced by the presence of a circumferential notch, the stress state and the high initial stress concentration at the notch bottom. The major conclusions drawn from these previous investigations were as follows: I. The magnitude of the triaxiality at fracture depends primarily on the initial notch depth. Its effect is a great reduction in the average ductility (contraction in area at fracture in the notched section) as compared with that observed in uniaxial tension. This triaxial stress state occurs at a point in the interior of the notch specimen. It determines the notch ductility if the notch is mild and/or the metal possesses a considerable ductility. On the contrary, brittle specimens probably fracture on the metal surface (at the notch bottom) at which point biaxial stress state is present. This biaxiality also considerably reduces the ductility of the metal. For small notch ductilities the notch strength and the notch ductility become very sensitive to embrittling factors. This is contrary to the behavior. of the ductility values derived from a conventional tensile test, which are comparatively insensitive.

Jan 1, 1947

By Alfred Brooks

THE only oil produced in Alaska in 1923 was obtained from a dozen small wells, one of which was drilled during the year on the single patented tract of petroleum land in Alaska, in the Katalla field. These wells are owned by the Chilkat Oil Co., which finds a ready local market for its product in the form of gasoline produced in its own refinery. The search for oil has been continued, but except in the Cold Bay field there has been no drilling in new fields during the year. Drilling was in progress during 1923 at Pearl Dome, 18 miles from the coast. Here the Associated Oil Co. sank two wells, about 500 and 950 ft. deep, but suspended drilling in June. The Standard Oil Co., drilling on the same structure, reached a depth of 300 ft. by August and is reported to have reached about 700 ft. by November. The company began the, installation of a second drill in August. George C. Martin, who hastily examined the Chignik region, south of the Cold Bay field, reports that what is known of the geology near Chignik is not favorable to the presence of petroleum. Kirtley Mather, who made a geologic survey of the northern part of the Alaska Peninsula, reports that some of the structures and the formations are favorable to the presence of oil. A small seepage has long been known in the region near the mouth of Douglas River, which flows into Cook Inlet. Sidney Paige last summer made an examination .of the oil seepages which have long been known near Cape Simpson, 50 miles southeast of Point Barrow, the northernmost point of Alaska. He reports that there are two very large seepages emanating from small ridges about a mile apart and several miles from the coast. These are marked by flowing petroleum, and cover many acres. There is a very large accumulation of petroleum residue at these seepages. The surface exposures consist of clay shales with hard thin partings of calcareous shale which lie nearly horizontal, and are probably, of Jurassic age. Mr. Paige and his two sub-parties explored a large area inland from the Arctic coast between Cape Beaufort on the south and Point Barrow and Cape Simpson on the north. He himself ascended the Meade River for 150 miles. These surveys indicate a wide distribution of what is believed to be the formation from which the Cape Simpson seepages emerge, which is probably of Jurassic age. These rocks near the north Arctic coast are little disturbed, but are increasingly folded to the south, toward the mountains. No other seepages have been found, but what is known of the geology is not unfavorable to an oil field. This entire region lies in Naval Petroleum Reserve No. 4, and it was examined by the Geological Survey at the request and expense of the Department of the Navy.

Jan 3, 1924

By Charles Jones

Discussion of the paper of CHARLES COLCOCK JONES, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 105, September, 1915, pp. 1887 to 1898. D. A. LYON, Salt Lake City, Utah.-For some years I have been interested in the iron-ore deposits of the Pacific Coast, and I feel very much indebted to Mr. Jones for the information he has given us on this subject. I think that we are also very much indebted to him for having presented this paper, as he has given us reliable data in shape of facts and figures, which is just what we need in considering whether or not it would be commercially feasible to attempt to establish an iron and steel industry on the Pacific Coast. Personally, due to lack of market, I do not think it is a commercially feasible proposition at the present time. Mr. Jones states that pig iron can be produced on this coast as cheaply as it can be produced in Pittsburgh. Even. so, what can be done, with it after it is produced? To begin with, iron produced on the. Pacific Coast has to compete with iron produced in China. Last year I had occasion to investigate the subject of the market for iron and, steel on the Pacific slope, and found that it was possible for the producers of Chinese iron to sell it for much less than the price for which iron can be produced in the West, and also for less than eastern pig iron is now sold for, even when shipped through the Panama Canal. I was informed that the agents for Chinese iron had instructions to sell it for $1 or $2 less per ton than that asked for other irons on the market. Of course, I realize that the competition of Chinese iron may not be important, but even if it is not, and even though pig iron ,can be produced at the cost given by Mr. Jones in his paper, I do not see any immediate chance of its being so produced, due to lack of market. C. C. JONES, Los Angeles, Cal.-Mr. Lyon is right. It is a fact that Chinese pig is being sold in San Francisco on some large contracts at $18.50 a ton, while $19 is the usual price. We ought to produce iron. on this coast at $14. Personally I do not think Chinese iron is ever going to be an important factor. It is a bugbear out here now. You are not going to have much Chinese pig iron in .this country. Our little friend Japan is going to absorb everything it can. The price of Chinese pig iron at $18 is about as low as it will ever get. If we can show you that we can produce this iron here at the same price as at Pittsburgh, I. think you will have a good opportunity to compete with anything China or India can ever do. Costs there are very low now. They are going to come up by leaps and bounds in the next few years. The labor cost over there may be very low now, but I. have seen some men from there quite recently

Jan 12, 1915

By T. W. Healy, P. Somasundaran, D. W. Fuerstenau

The flotation behavior of quartz in the presence of alkyl ammonium acetates as a function of alkyl chain length has been interpreted in terms of hemi-micelle formation at the solid-liquid interface. The van der Waals cohesive free energy that is responsible for hemi-micelle formation has been found from these results to be 1.0 kT per CH2 group. This is in excellent agreement with literature values obtained from research on the properties of micelles in bulk systems. Collectors of the type CH3(CH2)n-2CH2-P, where P is a polar group and n is the number of carbon atoms in the straight alkyl chain, will induce flotation of an appropriate mineral at lower concentrations as n increases. This reduction in collector concentration with increasing n has been reported for such systems as xanthates on sulfides1,2 and amines on quartz.' The effect of chain length of alkyl surfactants on such solution properties as conductivity,' surface tension,' and solubility6 and such interfacial properties of solids as contact angle7 and electrokinetic potential8 have received considerable attention, but only limited quantitative descriptions of the effects have been given. The electrokinetic studies of alkyl amine salts on quartz indicated that the solution concentration of collector at which the marked change in electrokinetic potential of quartz occurs decreases systematically as the length of the alkyl chain increases. The aim of the present work was to obtain a quantitative description in terms of current theories of flotation of the effect of the hydrocarbon chain of alkyl ammonium acetates on the flotation behavior of quartz. BASIC PRINCIPLES The marked changes in electrokinetic potentials of quartz in dodecylammonium acetate (DAA) solutions were postulated to result from the association of adsorbed collector ions into two-dimensional aggregates, called hemi-micelles.9 Subsequently, the rapid increase in flotation rate of quartz was shown to coincide with hemi-micelle formation." We would like to discuss briefly the concept of hemi-micelles in terms of recent interpretations of micelles in bulk solution. Micelle hypothesis: In dilute solutions, alkyl ammonium and related salts behave as ordinary strong electrolytes, but at a certain concentration there is a marked change in physical properties of the solutions, e.g., in equivalent conductance, transport number, freezing point lowering and viscosity. To account for these phenomena, McBainl1 introduced the concept of micelles, which are aggregates of long-chain ions. It is believed that the ionic heads of the constituent ions of the micelle are in contact with water, whereas the nonpolar groups turn away from it and are in contact with each other. Work must be done to bring these charged polar groups together, but energy is gained (i.e., so called van der Waals cohesive energy) when hydrocarbon chains are expelled from the water and allowed to associate. For a given polar group, the tendency to form micelles will therefore strongly depend on the hydrocarbon chain length. Theoretical treatments of micelle formation by Shinoda12 and Phillips13 and others lead to the following expression for the concentration at which micelles form (the critical micelle concentration or cmc) in aqueous solutions of long- chain electrolytes

Jan 1, 1964