Search Documents

The failure of finely-divided sulfide particles to respond to flotation has resulted in a significant loss of our natural resources. As mentioned by Professor Arbiter, the overall recovery of copper from porphyry copper ores is generally between 80 and 85 percent. The recovery of copper sulfides from these ores is about 90 percent, the difference in these recoveries being due to failure of oxide copper minerals to respond to flotation. The 10-percent loss of sulfide copper has not been studied. Losses are known to be in the fractions finer than 74 microns, but the sizes that are not responding to flotation have not been established. In the case of molybdenite, however, it is known that particles finer than about five microns are not recovered. Work in other systems, notably the hematite-quartz system, has shown that good flotation of very fine particles from natural ores is possible (1, 2). The size distribution of one ore that was researched is given in Table 1, and as shown, approximately 50 percent of the ore was finer than 10 microns. Flotation experiments were conducted with this ore, which contained 45 percent iron, utilizing octyl hydroxamate as collector and without any desliming (1). The results of these experiments are presented in Table 2. From the standpoint of mechanisms of collector adsorption, similarities exist between those occurring in the hydroxamate-hematite system and many xanthate-sulfide systems. .This is, multilayers of ferric hydroxamate are present on hematite under flotation conditions (1,3).

Jan 1, 1979

By Eugene Guccione

One of the world's most respected scientists, Dr. Hans A. Bethe (see box) has concluded that if anything can solve the energy crisis, it will be coal and uranium. "It is an illusion to think that we can solve our problem by energy conservation alone. For the next few years, conservation must play a very important role, but at the same time, we must see and develop all our alternative energy sources," he said. In his series of five lectures on the energy crisis, given at the University of Utah while he was visiting professor there during February 1974, Dr. Bethe examined all the existing and newly proposed energy sources. He very quickly ruled out solar power, wind power, and tidal power. Solar power, he said, would be 3% to 4 times more expensive than nuclear energy and would only make sense in tropical areas; wind power, which could at best produce one-tenth as much energy as solar, is "for the birds;" and tidal power, which can be exploited in only a very few coastal locations, is "for the fish."

Jan 5, 1975

By William Kelly

An extensive swamp covers a large part of the town-site of Norway and adjacent laud. Through this swamp run two parallel oreformations. In the north one is the Aragon mine. The south one passes into the swamp on the Harrison property. On the edge of the swamp, about 1000 feet from the Aragon mine, a diamond drill, in the fall of 1889, located the ore-bearing formation and a probable ore-body. To explore further and develop this ore, the Penn Iron Mining Company proposed, in the spring of 1890, to sink a shaft. The drill had shown the depth of the glacial drift to be more than 60 feet. A test-pit near the location of the proposed shaft had struck, at a depth of 20 feet, an amount of water which a 200gallon pump was unable to lower. At the Aragon, a few years before, a shaft had been sunk to hard pan with great difficulty and many delays by the usual method of driving laths. Under the conditions it was decided to sink a caisson- or dropshaft. Two 40-horse-power boilers, a Lidgerwood engine with 4foot drum, and a good derrick were set up; and two No. 10 Kuowles

Jan 1, 1892

By Francis M. Walters, Irvin R. Kramer

THE substitution of cobalt for part of the nickel in Invar was found by P. H. Brace1 to lower the coefficient of expansion. Scott1 extended the use of cobalt to alloys of higher inflection temperatures. Such alloys have a larger temperature range of low expansion than those without cobalt, and [ ] their use up to 400° or 500°C. offers decided advantages in certain applications. However, it has been found that the iron-nickel-cobalt alloys are not stable in this temperature range. EXPERIMENTAL METHODS Two methods were used in studying the stability of the low-expansion iron-nickel-cobalt alloys. Dilatometer specimens were held at 480°C, for 9 months and the change in expansion characteristics was determined. Filings were held for about 2 months at various temperatures and the change in structure was determined by X-ray diffraction. As shown by Table I, the alloys studied covered a wide range in nickel plus cobalt content (which determines the inflection [ ] temperature) as well as some variation in the ratio of nickel to iron (which controls the temperature of the gamma to alpha transformation). Included also are alloys containing carbon and vanadium, carbon and titanium and three with various amounts of copper. The alloys were melted in a high-frequency induction furnace with a magnesia crucible, using ingot iron, electrolytic nickel and commercial cobalt. Fifteen-pound heats were cast into iron molds after deoxidizing with silicon, or

Jan 1, 1941

By William Reynolds

THIS paper deals with the results of a study of the application and development of mining machines for cutting out and removing dirt bands in bituminous coal beds. FACE PREPARATION When one or more dirt bands1 occur in a seam of coal, the problem of elimination of impurities becomes manifest. The degree of complete-ness to which these impurities are removed at the face has an important bearing upon labor costs, haulage costs and outside cleaning costs, and often the ash content of the product is markedly affected. Yet, because the present-day miner is paid for the number of tons he loads he often lacks interest in the quality of the coal. To insure a clean product, a system of penalties for dirty coal is enforced, but control of extraneous impurity content in the loaded coal is often inadequate and ineffectual when coal and banded impurity are shot as one. It seems only logical that to reduce the amount of impurities by proper face preparation before the men are permitted to load the coal is the most efficient method of preparation.

Jan 1, 1936

By M. Karfakis, K. Kim, R. V. de la Cruz

The in situ deformability of a closely jointed basalt rock mass was determined by two different methods: the NX-borehole jack method where displacements of opposing curved platens were related to applied hydraulic pressures, and the modified Goodman jack method where tangential strains on the borehole walls were related to induced tangential stresses. The modulus obtained by the modified Goodman jack method were much higher than those obtained by the NX-borehole jack method. To explain the discrepancy, the influence of fractures and test variables, such as depth, orientation, hole location, and applied pressure on the calculated modulus of the rock mass, were analyzed by factorial analysis. It was found that the orientations and measurement depths have statistically significant effects. The in situ deformability values obtained by nonlinear regression analysis were also found comparable with other measurements and empirically predicted values for the basalt rock mass.

Jan 1, 1984

By R. S. Dean

The careful work of Gross and Zimmerleyl has established the fact that the energy actually used in grinding is proportional to the new surface produced. This confirmation of Rittinger's law was made by crushing quartz in a frictionless drop-weight machine and determining the surface of the quartz by its rate of solution in hydrofluoric acid. The details of this procedure have been described adequately elsewhere and need not be repeated here. The resultant data furnish the only available basis for comparing accurately the efficiency of grinding machines. This method is so cumbersome experimentally that it has been little used. As an alternative all sorts of approximations have been proposed. The best of these is complete size analysis by sieving and elutria-tion. Such procedure is very lengthy and difficult to carry out accurately. Furthermore, any sizing method becomes very inaccurate for determining surface with very fine sizes where the ratio of surface to volume becomes very large. To avoid the lengthy and difficult technique of elutriation it has been proposed to estimate the size distribution below 200 mesh from various probability formulas. Such a procedure is at best an engineering approximation; at worst it is a mere guess. Some time ago Dr. V. H. Gottschalk2 found that the coercive forces of magnetite powders were directly proportional to the surface area, regardless of size distribution. It was at once apparent that this furnished a method for determining grinding efficiency quickly and accurately. The only requirement was a single determination of the relation between the work input of the Gross-Zimmerley drop-weight machine and the coercive force of the resultant crushed magnetite. For this purpose Ural Mountain magnetite in definite octahedra was

Jan 1, 1939

By A. Lee Barrett

The Maintenance Committee of the Coal Division of the American Institute of Mining and Metallurgical Engineers is presenting with this report the first of a series of cost comparisons which it plans to present the Institute. The plan is to assemble maintenance cost on all equipment connected with mechanical operations at the face of coal mines, to arrange these costs by districts, to make comparisons between districts, and within districts. This particular report covers data with respect to mobile loading machines, including both "on-track" and "off-track" equipment. It is anticipated—in fact, considerable data have already been accumulated—that next year complete maintenance costs by districts can he presented for complete loading units, including the various classes and combinations of on-track and off-track equipment. Data have also been collected with respect to some phases of maintenance methods and certain recommendations of the committee are included dealing with maintenance problems. In the assembly of these data more than 120 questionnaires were sent to operating companies throughout the United States. At the time the report was written 33 questionnaires had been returned with completed information and an additional group of companies had written that the information requested was not at present available but that they hoped to have such information available in the not far distant future. The replies as

Jan 1, 1947

By K. N. Han, H. Lee, M. C. Fuerstenau

An investigation of the recovery of finely-divided cassiterite and silica particles less than 1 µm (1200 mesh) in size has been carried out using packed and fluidized beds. The bed particles used included cassiterite and silica particles ranging from 44 to 210 µm (325 to 70 mesh). Effects of various system parameters on the recovery and selectivity of cassiterite fines were investigated. System parameters included pH of the slurry solution, superficial velocity, slurry concentration, and bed particle sizes. High recoveries of cassiterite fines were obtained at pH 4.0 and slow slurry flow rates. In a packed bed system, recovery of cassiterite fines was greater than 95%, while that of silica fines under the same conditions was about 35%. Although the total recovery per pass is not as good as the packed bed, the fluidized bed system exhibits good recovery in general and an excellent selectivity of cassiterite fines. There is an optimum superficial velocity, vo, for the rate of fine particle uptake and the apparent rate constant has the form of Kvo1/2- K'vo, where K and K' are system constants.

Jan 1, 1985

By H. S. Drinker

I. The Mines THE first discovery of zinc on the property now worked by this company was made by the celebrated mineralogist, Prof. William Theodore Röpper, in 1845. Different claimants kept the property in continual litigation till 1861, when everything was satisfactorily settled by the purchase of the land by the company, who have worked it ever since. The mines are situated in a valley, four miles south of Bethlehem, Pa., in Lehigh County. The valley is from two to three miles broad, and is bounded on the north and south by syenitic hills. Syenite underlies the valley, and upon this is deposited the Potsdam sandstone, then a layer of slate, and, finally, a dolomitic limestone, belonging to the Chazy or Black River formation, in which the zinc deposits are inclosed. The rocks occur in folds, and have evidently been subjected to tremendous pressure from below, the zinc deposit being found in an anticlinal axis, in nearly vertical veins. It is supposed that the zinc was originally disseminated through the

Jan 1, 1873

By Carle Hayward

THE effect of copper on steel has been studied by numerous investigators. Before modern testing methods had been developed, blacksmiths noted red shortness in iron, the cause for which was ascribed to the presence of copper. Numerous papers have been published on the corrosion of steels containing various amounts of copper, and a few writers have discussed the effect of copper on the mechanical properties of steel. The purpose of the investigation described in the following paper was to obtain additional data on the mechanical properties of medium-carbon steel containing small quantities of copper. Among those who have published results of mechanical tests on copper steels are Ball,1 who states that copper increases the tensile strength and 'hardness but lowers the elongation. Stead2 states that copper steels closely resemble nickel steels containing equivalent percentages of nickel,, as regards tensile strength, resistance to shock, corrosion and hardness. Wigham 5 found that copper in small amounts had no injurious effect on steel. Breuil4 found that with 1 per cent. carbon, copper lessened the brittleness of steel and in low-carbon steel it increased the tensile strength and lowered the ductility slightly. H. H. Campbell 5 states that copper up to 0.25 per cent. slightly raises the elastic limit, elongation and reduction of area.

Jan 1, 1918

By R. S. Dean

The careful work of Gross and Zimmerleyl has established the fact that the energy actually used in grinding is proportional to the new surface produced. This confirmation of Rittinger's law was made by crushing quartz in a frictionless drop-weight machine and determining the surface of the quartz by its rate of solution in hydrofluoric acid. The details of this procedure have been described adequately elsewhere and need not be repeated here. The resultant data furnish the only available basis for comparing accurately the efficiency of grinding machines. This method is so cumbersome experimentally that it has been little used. As an alternative all sorts of approximations have been proposed. The best of these is complete size analysis by sieving and elutria-tion. Such procedure is very lengthy and difficult to carry out accurately. Furthermore, any sizing method becomes very inaccurate for determining surface with very fine sizes where the ratio of surface to volume becomes very large. To avoid the lengthy and difficult technique of elutriation it has been proposed to estimate the size distribution below 200 mesh from various probability formulas. Such a procedure is at best an engineering approximation; at worst it is a mere guess. Some time ago Dr. V. H. Gottschalk2 found that the coercive forces of magnetite powders were directly proportional to the surface area, regardless of size distribution. It was at once apparent that this furnished a method for determining grinding efficiency quickly and accurately. The only requirement was a single determination of the relation between the work input of the Gross-Zimmerley drop-weight machine and the coercive force of the resultant crushed magnetite. For this purpose Ural Mountain magnetite in definite octahedra was

Jan 1, 1939

By W. A. Oates, J. S. Blakemore, E. O. Hall

AS part of an investigation into the effect of hydrogen on the serrated yielding of Ni-Cu alloys,' it was necessary to determine the solubility of hydrogen in the alloys of interest. With the exception of the work by Fukusima and Mitui2 who investigated the solubility of hydrogen in solid Ni-Cu alloys at 20 wt pct intervals at 1050°, 700°, and 350°C, the information in the literature is limited.3-10 Alloys were prepared from deoxidized Analar Copper and Mond Nickel pellets.' Wire samples were hydrogenated at 7.8 atm in an autoclave consisting of 5 ft of thick-walled Inconel 600 tube with a resistance furnace around the middle portion. The top end, at room temperature, was fitted with a safety valve, a calibrated pressure gage, and a sample inlet, while the bottom end, again at room temperature, was filled with water. After reaching equilibrium samples were quenched by dropping from the high-temperature region of the autoclave into water. They were then quickly transferred to liquid nitrogen where they were stored until analyzed for hydrogen using an Exhalograph.11 The results, which are shown in Fig. 1, represent the mean of two separate determinations on each sample. Because of the lower level of hydrogen at the high copper end of the series, the results here are of poor precision using this method. Fortunately, the results of Himmler9 using the Sieverts technique are available for these copper-rich alloys (>80 at. pct Cu)

Jan 1, 1969

By David J. Mack, Chin Bea Kim

The decomposition of the Ni-Zn eutectoid at 56 wt pct Zn was studied by isothermal transformation. Its progress was followed by metallographic, hardness, and X-ray diffraction methods. Three transformation products were found: lamellar pearlite at high temperatures; an intermediate temperature structure; and martensite at the lower temperaCures. No transition structu,ves were found. THE decomposition of the Ni-Zn eutectoid at 56 wt pct Zn was stuadied as part of a long-range program of study on the eutectoid transformation in alloy systems which do not have one or more components which exhibit allotropy. Available information on the Ni-Zn eutectoid transformation is limited to that presented in connection with the determination of the phase dilagram. No systematic studies of the eutectoid were found in the literature, alkhough the microstructures of the Ni-Zn eutectoid were reported by Tamuru.3 X-ray diffraction data exist for the ß, ß1, y , and y1 phases.' EXPERIMENTAL PROCEDURE The eutectoid alloy was prepared from "A" nickel shot and Bunker Hill super-purity zinc (99.998 pct).

Jan 1, 1962

By A. Lee Barrett

The Maintenance Committee of the Coal Division of the American Institute of Mining and Metallurgical Engineers is presenting with this report the first of a series of cost comparisons which it plans to present the Institute. The plan is to assemble maintenance cost on all equipment connected with mechanical operations at the face of coal mines, to arrange these costs by districts, to make comparisons between districts, and within districts. This particular report covers data with respect to mobile loading machines, including both "on-track" and "off-track" equipment. It is anticipated—in fact, considerable data have already been accumulated—that next year complete maintenance costs by districts can he presented for complete loading units, including the various classes and combinations of on-track and off-track equipment. Data have also been collected with respect to some phases of maintenance methods and certain recommendations of the committee are included dealing with maintenance problems. In the assembly of these data more than 120 questionnaires were sent to operating companies throughout the United States. At the time the report was written 33 questionnaires had been returned with completed information and an additional group of companies had written that the information requested was not at present available but that they hoped to have such information available in the not far distant future. The replies as

Jan 1, 1947

By J. Kostuik, M. J. de Bastiani

Located in the Elliot Lake mining district of Canada, the Denison mine lies between Sudbury to the east and Sault Ste. Marie to the west. This area is overlain by Huronian sediments filling a basin in the Keewatin basement complex. Subsequent folding of these sediments developed a synclinal structure, known locally as the Quirke Lake Trough, which forms the northern portion of the now famous big Z structure, the geological trademark of this region. Plunging to the west and extending nine miles from the granite outcropping in the north to the Keewatin lava contact to the south, the syncline has dips of 10° to 45° on the north limb and 10° to 20° on the south limb.

Jan 12, 1960

By E. Nelson Fell

As this plant is the first ever erected in British Columbia for the treatment of tailings by the cyanide process, and as the ores of this, mine are of a character not unusual among gold-ores of this Province, it is probable that a description of the principal features of the plant, and of the methods employcd in its operation, may be interesting. These works were designed after a careful study of the process, in a small experimental plant, for a period of six months. During this period ten percolation-tests on charges of tailings of 1100 lbs. each, eight percolation-tests on similar charges of concentrates, and twenty-six tests 011 concentrates in a revolving barrel, were made, besides laboratory-experiments. The ore consists of a quartz gangue, containing a little lime and variable quantities of the sulphidcs of iron, lead and zinc. The following figures, giving the analyses of the ore before milling, and of the tailings after milling, which constituted the material to be cyanided, are based on the daily samples taken during February and March, 1901.

Jan 1, 1902

By Thomas MacFarlane

During the last fifteen years the progress made in the science of lithology has been of a very marked character. From being a miscellaneous collection of facts and observations regarding certain mineral aggregates seemingly incapable of systematic arrangement, it has become a most interesting and orderly department of science. The investigators who have brought about this great change have recorded the results of their labors, and placed at our service an extensive and varied literature on the subject. To this I have paid some attention, and partly from studying it,, partly from my own observations, I have wrought out a classification of original or crystalline rocks, which I venture to bring under the notice of the members of this Institute. The practical importance of the subject will be acknowledged when it is considered that rock species are not without their influence on the contents of the mineral veins which intersect them. Besides, the Institute has been doing good service in defining terms in metallurgy, and no doubt in mining and geology we might

Jan 1, 1880

By J. W. White, J. M. Richardson

Mass balance calculations on industrial grinding circuits are routinely performed during circuit design as well as during post-installation evaluation of operating circuits. Though such routine mass balances are straight- forward, a systematic approach can yield substantial long-term benefits. This chapter presents and evaluates several approaches useful for achieving various circuit design objectives and also considers several methods for reconciliation of data collected around an operating circuit. Numerical examples illustrate the basic concepts and techniques.

Jan 1, 1982

By Henry Souther

It is generally admitted that a god, practical and commercial set of specifications for the use of the many purchasers of cast-iron does not exist. A few good sets are in the hands of large buyers, but even these are very different, contradictory, and not intended to cover a wide range of product. Furthermore, most of them have been prepared to cover but one branch of the industry. It is strange that purchasers of cast-iron have not looked into this question long ago and demanded good, uniform cast-irou. Probably cast-iron has been discarded from many uses because of its failure in a few instances, even though the failure was due to ignorance of the quality of the iron, or perhaps to abnormally bad iron. Some foundrymen seem to consider all gray iron from a given foundry as uniform, especially if they know that it has been made from certain well-known brands of pig. It is likely that with standard specifications and the increase of knowledge necessary for their intelligent employ-

Jan 1, 1905