Search Documents

By Casimir Constable

DURING the years 1875 to 1879 I had charge of the Rockwood furnaces and mines, situated forty miles from the nearest railway communication at that time, and one hundred miles north of Chap tanooga, Tenn., by the Tennessee River. The small furnace with old-fashioned stoves, then in blast, was built under great difficulties by General Wilder. The early conditions were somewhat as follows: The ore was fossil ore of the Clinton group ; very fine and generally wet, without other admixture. The coke had a large amount of ash, and the fur" nace appeared to be badly scaffolded at times. On many days only a few tons of iron could be obtained. The founder generally id creased the revolutions of the engine when signs of chilling appeared,. The cinder at such times was black, very scoriatious, often closely resembling mill cinder. When the pressure was increased (the joints being the old-fashioned rust joints), leaks in the blast-pipe occurred It was noted that when the blast was stopped, and the leak bolt imperfectly remedied, the furnace improved a little. This set me thinking on the right track; and I took the responsibility of be coming my own founder for a time. A scaffolded condition had existed, and the situation was a trying one. Strange to say the negroes proved excellent furnace-men. Conceiving the hearth of the furnace to be similar to the grate area of a steam-boiler, capable of disposing of but so much fuel per hour, and requiring only a corresponding amount of air, it follows that an excess of air will burn the fuel not yet arrived at the hearth!, and raise the melting-point far above the tuyeres. This might pro duce scaffolding or at any rate choke the boshes, and leave less fuel to be consumed in the hearth. Thus for the time being less ail;. would be needed, as the continued burning of fuel in and above the boshes, would only aggravate the trouble. This condition of affairs accounted for the black cinder; the heat above having melted ore not yet perfectly reduced. This view decided me to reduce the revolutions of the engine; thefurnace finally became gray, as might have been expected. Any attempt to increase the speed produced black cinder and hard iron ;

Jan 1, 1883

By R. A. Feemster, C. M. Rader

Because of the necessity for taking regularly occurring open-flow tests in prorated high-pressure oil fields, much gas is turned to atmosphere by way of vertical vent lines leading away from the oil and gas separator. In the past, measurement of such gas has been accomplished by several methods, usually by use of the open-flow Pitot tube. The use of the closed-flow Pitot tube has been avoided apparently chiefly because the ordinary vent-line hook-up makes it necessary to apply the instrument closer to a bend, valve, or obstruction in the pipe than is recommended by rules of good practice. The many advantages that would result from the application of the closed-flow Pitot tube prompted investigation of the actual effect upon quantity rate of flow measurements computed from data obtained with the tube in a normal working position, which is closer to the tee at the base of the vent riser than is usually considered as giving highly accurate results. An effort Was first made to compare the results thus obtained to those under ideal conditions and at high velocities To make this comparison, knowledge of the characteristics of gas flowing at very high velocities is essential. Research for such information indicated that little or no work had been done that would give data necessary for such a comparison, therefore the problem was changed to a test designed to determine the relationship between quantity rates of flow as measured by an orifice meter and a Pitot tube placed at the center of a pipe eight diameters from a tee or ell at the base of a vent riser, through which gas is flowing under low pressures at very high velocities. To determine this relationship, a series of tests was run on a number of 8-in. iron-pipe vent riser., in which the Pitot tube data were taken at the position as stated above. Gas from a wet-gas gathering system was passed through an orifice meter setting and thence to atmosphere by way of the vents. Data were taken simultaneously from the orifice meter and Pitot tube from which computations for comparisons were made. The actual method of comparison is discussed later in this paper. Since Pitot-tube information is usually given in general terms, and not readily usable, it will be the purpose of this paper to discuss the applica-

Jan 1, 1934

By W. M. Peirce, E. A. Anderson

A FEW metals have been known since the dawn of history. Many have been prepared in quantity only within the present century. Zinc falls into an intermediate category, although there is some evidence of its existence in elemental form in Greece as early as the third or fourth century B.C. Nevertheless, the first important use of zinc antedates the earliest records of civilization. This first use was in the alloy, brass, which is roughly one third zinc. This continues to the present time as one of the major uses of the metal. The first production of brass, in light of present knowledge, was perhaps one of the 'most romantic and fortuitous of technical discoveries. Copper, the major constituent of brass, had been given to man by Nature in the native state; that is, as lumps of fairly pure copper. The art of melting and working it had been learned. But zinc does not occur as the metal in Nature and even if some early metallurgist happened to heat zinc ore with a reducing agent, the reduced metallic zinc passed off as vapor and was lost. Doubtless some early coppersmith, melting copper in accidental contact with zinc ore, reduced the zinc, and the vapor was absorbed by the molten copper. Its color, hardness, and other properties were thus wonder- fully changed. And so the earliest metallic form of zinc, as nearly as we can deduce, existed in the alloy brass. Probably knowledge of the kind of rock with which to heat copper to change it to brass, the best

Jan 1, 1953

By W. O. Hotchkiss

DURING the summer of 1927, the Department of Terrestrial Magnetism of the Carnegie Institution of Washington joined with the Michigan College of Mining and Technology in conducting a series of earth-resistivity measurements in the Michigan copper country. The geological structure in this section is quite varied and fairly well known. The purpose of the investigation was to discover the correlation between the variations in electrical resistivity of large masses of soil and rock in place and the geological structure below the surface. The work done may be roughly divided into two parts: (1) Measurement and study of the variations in resistivity with depth, or with volume, to establish such general relations as exist between the two: and (2) the determination of the specific resistivity of various formations in order to make available more fundamental data which may aid in the interpretation of the results of the former type of measurement. A report by Mr. Rooney, which gives in detail the measurements made and the results obtained, forms the basis for this article. MEASUREMENT AND STUDY OF VARIATIONS IN RESISTIVITY The possibility of applying data from measurements of the physical properties of earth material to the 'study of the geological structure has long been recognized, and a number of methods for determining the position and character of concealed rock strata by means of seismic, gravitation, magnetic and electrical measurements made on the surface are being used with varying degrees of success. One physical property which varies widely for different materials, and hence affords an opportunity for distinguishing between them, is their electrical resistance. Locations were selected where the geological structures were well known and where the depths to the water level and bed rock had been determined by drilling. The problem was to determine the value of measurements of resistivity and its variations as indications of the geological structure below the surface.

Jan 1, 1928

By Alfred H. Bell

The year 1936 in Illinois was marked by considerably increased activity in drilling, both wildcat and proved territory, in leasing, and in seismic and geologic exploration. Of the 92 oil and gas wells completed during 1936 in Illinois, 49 were oil wells, 3 were gas wells and 40 were dry holes. This compares with but 34 completions in 1935. The total of the daily initial productions of the new oil wells was 1755 bbl., or an average of 36 bbl. per well. One new field was discovered, the Bartelso field in Clinton County. The leasing of some large blocks of acreage in Clay, Marion, and other counties by the Carter Oil Co. in the late fall of 1935 was followed in 1936 by extensive leasing in southern Illinois by 10 major companies and many smaller companies and individuals. It is estimated that 2½ million acres were under lease by the end of 1936. Seismograph surveying has been carried on by about seven companies, and the number of seismograph parties operating in Illinois has varied from six to eight throughout most of 1936. It is estimated that approximately two million dollars has been spent in the state in seismic and geologic exploration and in leasing during the last quarter of 1935 and all of 1936. Production of crude oil in Illinois in 1936, according to the Bureau of Mines, was as follows: Barrels Barrels January...................... 325,000 July........................ 402,000 February..................... 294,000 August..................... 380,000 March....................... 396,000 September.................. 386,000 April......................... 347,000 October.................... 393,000 May......................... 389,000 November.................. 363,000 June......................... 383,000 December................... 387,000 4,445,000 This 4,445,000 bbl. was an increase of 3 per cent over 1935. Although this increase was due largely to the fact that production was not artificially curtailed, it also reflects some new production and some increases in production from repressuring and water-flooding, which offset the

Jan 1, 1937

By W. J. Reagan

A survey of the literature on bottom-cast practice gives but Scant information as to some of the real facts concerning this most int'eresting method of steel manufacture, and some of the information available is very misleading. An exceptionally good description of this met,hod of pouring or teeming is to be found in an English publication2 on the heterogeneity of steel ingots. Quoting from this paper: (a) With bottom teeming, the metal rises steadily and progressively in the mold with the minimum possible agitation, the main force of the stream coming from the ladle being broken down or retarded by the down gate or runner. Further, the stream of metal from the ladle, under these conditions of casting, is invariably maintained at a much more continuous rate and is steadier than with top teeming. (b) In view of the facts referred to in (a) it follows that with bottom teeming the metal is not exposed to atmospheric oxidation to anything like the same degree as with top teeming. In this paper it is intended to detail briefly some of the advantages of bottom-cast practice and to discuss the possibilities of iron-oxide control in the basic open-hearth furnace. A description of the type of charge, ingot rnold set-up, etc., is found in detail in an earlier paper.3 Design of Ingot Molds In any kind of steel manufacture, ingot-mold design is important. L. H. Nelson4 lists in the order of their probable importance the following factors as influencing most the solidification of the ingot:

Jan 1, 1934

By H. E. Nold

THE raw materials of the ceramic industry are mostly clays. This raw material is ground, water is added and the mixture pugged into a moist, plastic, rather stiff mass. From this mass the desired units of manufacture are made (bricks, hollow building tile, sewer pipe, etc.). These units are dried; then placed in kilns and heated until the desired degree of vitrification is obtained.1 For firing ceramic ware, two distinct types of kilns are used; namely, periodic and continuous tunnel. PERIODIC KILNS Periodic kilns are those ordinarily seen in a brick plant. They are either round or rectangular. The raw, dried, formed ware is piled or set in the kilns to depths frequently exceeding 10 ft. The kiln is heated until the ware is matured, then gradually cooled sufficiently to allow men to remove the ware; then the cycle is repeated. The time duration of the cycle may be more than two weeks. In order that heat can be distributed uniformly throughout the pile or setting, the units are placed so as to leave open spaces or flues through-out the pile for the passage of the hot gases. Each kiln is provided with a number of fireboxes (usually 10 or 12) spaced equally in the outside wall. The fireboxes may be equipped with flat or inclined grate bars or they may have no grates at all (dead bottom). Down-draft kilns are most used. In these the hot gaseous products of combustion from the fireboxes are deflected upward by bag walls just inside the fire zone. From the top of the kiln the gases are drawn down through the setting, off through holes in the kiln bottom, and conducted to a stack or stacks. In up-draft kilns the fireboxes are usually set somewhat lower. The hot gases are drawn inward and upward through the ware and pass off from the top. Up-draft kilns find their greatest use in the firing of common brick. In either case the problem is to maintain, as nearly as possible,

Jan 1, 1933

By Joseph Hartshorne

The attention which this process has attracted, especially in Europe, has led me to believe that members of the Institute would be interested in a report of the progress which has been made in the year and a half that has elapsed since my paper on the subject was read at the Colorado Meeting of this Institute. As already described in that paper (Duns., xxvi., 380), this process is a modificatioii of the open-hearth steel manufacture, whether acid or basic, collsistillg essentially in the division of the charge between two furnaces, one of which is charged about two hours earlier than the other, and tapped into the other after the charge in the latter has become fluid, the slag of the first bath being removed from it during the transfer. This description still remains true as far as it goes, but further experience has demonstrated that circumstances will very materially modify the relation of the two furnaces to each other, and the character of the work done in each of them. The function of the primary furnace has become more clearly and entirely that of doing the rough work of desiliconiziug and dephosphorizing, while that of the second or finishing-furnace has become almost entirely that of decarburizing and finighing the heat. To indicate these developments and their results is the object of this paper. In order to avoid needless repetition, I shall try to accomplish part of this object by giving a short resume' of what has been published elsewhere on this subject since my former paper was read. This will at least enable those interested to study the matter for themselves from original sources. Since that time the following papers have been read and published: " The Bertrand-Thiel Process of Making Steel," by Percy C. Gilchrist (Cleveland Institution of Engineers, Session of 1896-

Jan 1, 1899

By Charles Albert Ashburner

THE stratigraphical geology of the vicinity of Buffalo has always been of great interest on account of its bearing on the origin and history of the Niagara-river gorge, between the Falls and Lake Ontario. Recently, however, the character and thickness of the strata which underlie Buffalo have acquired more practical and economic importance on account of their relation to the possible occurrence of natural gas in commercial quantity near the Niagara river. In a paper presented at the Duluth meeting (l887), on " Petroleum and Natural Gas in New york State" (Trans., xvi., 906), I gave a brief description of the four wells which had been drilled by the Buffalo Cement Company between 1883 and that time. One of these wells is 1305 fret deep; and, at the time that my paper was finally revised for the Transactions (June, 1888), it was still an open question whether the drill in this well had reached the Niagara limestone, or had penetrated the Medina sandstones and shales, which latter are boldly exposed in a number of localities in the district, hut more particularly along the Niagara river in the vicinity of Lewiston and Qneenstown. The difficulty in this geological question at Buffalo has lain in the fact that no reliable determination could be made of the thickness of the strata included between the Corniferous limestone, immediately below which the drilling of the Buffalo gas-wells was commenced, and the Niagara limestone. On the other hand, the strata included between the latter limestone and the middle portion of the Medina sandstones and shales, have been minutely measured and studied in the Niagara gorge below the Falls by many American and European geologists. The first reliable section of these strata was constructed by Professor Eaton, and published in 1824 in his report on the Geological and Agricultural Survey of the District adjoining the Erie Canal. This section, extending from Lake Erie to Lewiston, is complete, with the exception that no thickness is given to the Salina or Onoudaga salt group,

Jan 1, 1889

By Philip W. Moen

It is with sincere regret that the members of the Institute will have heard of the death, on March 17th last, at Terre Haute, Ind., of Professor Charles 0. Thompson, A.M., Ph.D., President of the Rose Polytechnic Institute of that city, and for many years pre viously the head of the Worcester County (Mass.) Free Institute of Industrial Science, and in 1881 and 1882 one of the managers of this society. To us he was chiefly known by the excellent character of the work which he had performed, as a recognized leader among the technical educators of the country. He was a constant, and interested atten dant at our meetings, seeking to acquaint himself not less with all that was noteworthy in the practical attainments and developments of the branches of industry represented by our membership, than with such such facts as would be of service to him in shaping or guiding a wise course of instruction in the institutions of which he had charge. We shall not soon forget him, or the genial courtesy of his manner, or his ready words and thoughtful comments. Charles Oliver Thompson was born September 25th, 1836, at East Windsor Hill, Conn., where his father, Rev. William Thomp son, D.D., was professor in the Connecticut Theological Seminary, since removed to Hartford. The son was fitted for college under the late Paul A. Chadbourne, and entered Dartmouth College in 1854. He was graduated in 1858 with honors. In all the studies of his course he had maintained a high rank, but showed marked proficiency in chemistry and mechanical philosophy. In 1861 he received the degree of A.M., followed by that of Ph.D. from his own college in 1879, and from Williams in 1880. In September, 1858, the year of his graduation, he became principal of the Peacham Academy, Vt., remaining in that position until November of 1864, though during that period he devoted several months to practical work as a surveyor and civil engineer. Thus his experiences were developing the qualities which, later on, fitted him to carry out so successfully the plans of the thoughtful projectors of a new system of technical education, along a path before untrodden, but which the test of time and the indisputable proof of success have shown to be both wise and fruitful.

Jan 1, 1886

By J. J. Reed

The mines of southeast Missouri's Lead Belt have been in operation since 1864, almost 100 years. During this period about 10 pct of the total ore available has been left in place as pillars, and this now represents the best ore reserve left to the older mines. St. Joseph Lead Co. has been investigating various plans of pillar recovery for several years. The example to be described is only one possible approach under a specific set of conditions. Conditions vary greatly in the different areas within the Lead Belt, and the same approach would be entirely inadequate in certain other areas, but there are important sections where this system is clearly applicable. Horizon mining is practiced in the Lead Belt, and stopes may vary from 10 ft to well over 100 ft high. Fig. 1 is a plan view of 6100 stope, the area to be discussed. For these mines this is a small stope, only 10 to 12 ft high. Before any plans were drawn up for pillar recovery, three independent estimates of the pillar grades were made by the mine superintendent, the mine captain, and the mine geologist. After these results were averaged, pillars indicated to be of economic grade were marked for removal as shown. At this stage several alternatives were considered: 1) retreat with caving, 2) concrete replacement pillars, and 3) systematic bolting and retreat. A retreating system with caving was not chosen because the roof was known to be too bad even to permit loading a blasted pillar before caving would begin. Concrete replacement pillars would have been too costly and would have required a large crew, bulky materials, and unwieldy equipment. Systematic bolting was chosen as being most acceptable for the following reasons: 1) Limited area and spans were involved. 2) Only minor modifications to the jumbo would be required for bolting. 3) Only a two-man bolting crew would be needed. 4) Only compact bolting materials would be required. 5) The bolting plan could be modified to allow

Jan 1, 1960

By Stuart E. Buckley

The application of hydrocarbon equilibrium data to various problems encountered in refining and in natural gasoline recovery is an old and well established practice. Both generalized data and data on specific hydrocarbon systems have been made available by a number of investigators. More recently such data have been applied to the relations governing the separation of oil and gas both in the reservoir and at the surface. Most of the applications to production problems, however, have been based upon examinations of surface samples of oil and gas. This paper describes a technique that has been used satisfactorily in a number of cases to calculate directly from the hydrocarbon analysis of and auxiliary laboratory data on a subsurface sample of the reservoir fluid the behavior of the oil and gas during the various stages of separation at the surface incident to production. Types of Information Calculated The system of calculations is not designed to supplant field data, but rather to correlate with them laboratory data obtained under controlled conditions in order to obtain a more complete and exact picture than usually is possible through the use of field data alone. The chief advantage of the calculations is the possibility of their use at a minimum of both time and expense to determine completely the effect of any possible operating technique upon each of the following: (1) The gas-oil ratio resulting from liberation of the dissolved gas; (2) the composition and gasoline content of the liberated gas; (3) the composition and gravity of the residual oil; (4) the amount and composition of the gas liberated upon flashing the oil from the separator to the stock tank; (5) the shrinkage of the oil in passing from the reservoir to the stock tank. This information is frequently essential to the correct determination of the advisability of installing a natural gasoline plant, to design such a plant to take care of seasonal production, and to determine the optimum separator pressures to carry in various parts of a field.

Jan 1, 1938

By Norman D. Fitzgerald

The purpose of this paper is to analyze the behavior of oil securities during the six-year period January 1932 through December 1937. This period was selected because of its varied character. It includes the depths of the depression, the broad and spasmodic recovery, and the recession collapse. The first part of the analysis is devoted to the correlation of a number of economic factors with an index of 13 oil stocks. The second part is a comparison of the different,ial behavior of 6 oil stocks. The relationships developed here are only a few of many that might be considered in a complete analysis. The stock market is regarded as a barometer of business confidence and as such exerts an important influence upon corporate policies, particularly upon industrial expansion. The complex and continuously changing nature of its price structure, the ebb and flow of influences and the effects of impacts require dynamic rather than static analysis. When treated in this way, many of the important fluctuations in market prices and changes in the relationships between securities appear quite logical. The market for oil securities has varied widely in recent years. The Standard Statistics index of 13 oil stocks made a bull market peak of 166.7 in September 1929. The collapse of the boom and the ensuing bear market finally carried the index down to a low of 36.4 in June 1932. From this point oil stocks made an irregular recovery; they reached a top at 139.7 in March 1937, and after maintaining this approximate level through August, declined precipitously to 93.3 in December 1937. The prices of these 13 oil stocks have gone up and down under the influence of numberless variables. These variables are of two kinds, those external to the industry, and those that are solely due to its internal condition. The external factors are political, social, and economic, both domestic and foreign. These are the influences that induce the ebb and flow of all prices in general and security prices in particular. Among the internal factors are the regulation of industry, the development of new reserves and processes, and the disequilibrium due to lack of balance between supply and demand. Some of the simpler relationships are examined in this paper.

Jan 1, 1938

By Reginald S. Dean

THE widespread occurrence of manganese in low grade oxide and carbonate ores not amenable to mechanical concentration has led to extensive investigations of hydrometallurgical methods for producing a pure manganese compound suitable for further treatment. Manganese carbonate is the preferable compound. This product when fully crystalline and of not too fine crystal size is easily filtrable and stable in air. It can be converted to other compounds such as the oxides by heating in air or can be reacted with acids for producing salts. A useful hydrometallurgical process must produce relatively concentrated solutions that can be purified easily, reagents must be cyclically used, and heat requirements must be small. Neither the ammonium sulphate nor sulphur dioxide leaching processes that have been tested extensively fulfill these 'requirements. Other hereto-fore proposed processes have obvious limitations and have not been tried on a large scale. The present process is based on the discovery by the writer of a new group of aqueous manganese-ammonia complex solutions highly concentrated in ammonia, which permit rapid solution of manganous oxide to concentrations of 80 to 100 g Mn per liter and from which a fully crystalline, easily filterable manganese carbonate is precipitated by the addition of carbon dioxide and partial ammonia removal. Although the process may be carried out with many ammonium salts, commercial advantages dictate the use of ammonium carbamate, which is obtained when CO2 is passed into concentrated aqueous solutions of ammonia. If the carbamate is used, the only reagents, ammonia and C02, are volatile and may therefore be recovered from solutions and residues by heating, thus eliminating washing and extensive evaporation. Impurities are controlled easily as most metal oxides are either insoluble in the lixiviant or fail to precipitate with the manganese carbonate. Others are controlled by sulphide addition. The process has been tested extensively on a small scale on a wide variety of ores; including Three Kids, Artillery Peak, Cuyuna, and Chamberlain; as repre-

Jan 1, 1952

By Richard Moldenke

One of the gravest problems of the iron foundry today is the accumulation of sulfur in commercial scrap and its effect on the castings made therewith. The ordinary jobbing castings today show a sulfur content of 0.18 per cent;, and occasionally as high as 0.22 per cent. The product of the foundry during the war is undoubtedly to blame for this rapid increase and conditions will become worse as the millions of tons of gray-iron castings of the war period return to the foundry in the form of commercial scrap. In the ordinary cupola remelting of pig and scrap, at least 0.02 per cent. sulfur is taken up; often double that amount. The high cost and difficulty of obtaining pig iron during the war period compelled the use of considerable scrap in the mixtures; frequently charges containing 90 per cent. of bought scrap were melted. Naturally the sulfur content of the castings increased. Until the advent of the basic-hearth electric furnace, the only method of holding the sulfur within reasonable limits was to use high percentages of pig in the foundry mixtures. Pig iron seldom contains over 0.05 per cent. sulfur, if well made. With pig iron forming 60 per cent. of the charge and the gates, runners, rejections, and bought scrap the other 40 per cent., the sulfur content of the castings can easily be held down to 0.10 per cent. Pig iron, however, costs more than scrap even when melting loss differences are considered, hence as small a percentage as possible will be used. The recent advance in knowledge of rational melting and the consequent reduction in losses directly due to oxidation of the metal and cold iron, has permitted the acceptance of castings with a much higher sulfur content than formerly. The steel industry also is seeking to determine how high sulfur may go with safety. In the iron foundry, however, there is the danger of a low cupola bed or an unduly retarded air-furnace heat, with the consequent raising of the freezing point of the metal and segregation effects resulting from high sulfur with insufficient manganese. The iron foundryman must, therefore, have a means of correcting his

Jan 1, 1922

By R. G. Knickerbocker

The copper smelter and refinery of The Messina (Transvaal) Development Co. Ltd., at Messina, South Africa, was erected in 1920 and 1921, but initial operations were deferred until late in 1922 on account of the collapse of the copper market in the interim. Because the anticipated production was to be only 20 tons of copper per day from a high-grade matte containing 60 per cent copper, and because the ore did not contain gold or silver in quantities sufficient to pay for separation from the copper bullion, it was decided to design the plant along lines quite different from the modern smelteries treating large quantities of sulfide ores carrying appreciable amounts of gold and silver. The plant was built, therefore, for the production of copper by the Nicholls-James process. By this method two-thirds of the copper matte produced was roasted in a Merton calciner and charged into a bath of the remaining one-third portion of unroasted matte in a reaction furnace. The original design was not only novel in providing for the Nicholls-James process, but also in comparison with new plants built elsewhere, because of factors inherent in the locality. Sources of supply for machinery were very remote; it takes three months after the placing of an order to accomplish delivery of machinery into Messina from the United States. Native labor was available at 30 to 40¢ per 8-hr. shift. These factors permitted plant design which provided no overhead cranes, no matte ladles, no slag pots or other usual mechanical means of transportation between departments. The design resulted in a compact simple plant with furnaces arranged close together and terraced so as to provide for gravity transfer of molten material from one furnace to another and for manual disposal of products. Fig. 1 shows the relative location of furnaces. The three furnaces are parallel on successively decreasing elevations. A superimposed feed floor was provided above the furnaces. All three furnaces were provided with coal-dust burners served from a Bonnot system of coal-dust transportation, and the waste gases were discharged into waste-heat boilers. A short trial of the Nicholls-James process developed several facts which brought about a decision to abandon the process. Owing to the

Jan 1, 1934

By H. K. Shearer

Oil production in north Louisiana in 1937 was 28,668,070 bbl., an increase of 1,896,925 bbl., or 7.1 per cent over 1936, as against an increase of 178 per cent from 1935 to 1936. Gas production of 301,148 million cu. ft. from gas wells and 17,330 million cu. ft. of casinghead gas, a total of 318,483 million, was an increase of 33,483 million cu. ft., or 11.7 per cent over 1936. Well completions numbered 716, with 411 oil wells, 175 gas wells and 130 dry holes; compared with 346, 109 and 78, respectively, in 1936. There were 58 wildcat dry holes. In addition to the wildcat producers described and tabulated with the fields, there were two small, shallow gas wells in Sabine and Tensas Parishes, which did not open fields of any present importance. At the close of 1937 there were only five wildcat tests actually drilling, with nine others shut down or temporarily abandoned. Chief interest during 1937 was in development rather than discoveries. The only real discoveries were two deep gas and distillate fields, Bear Creek and Ruston. There were also three completions of gas-distillate producers from deeper formations in old fields, of which the most important was at Cotton Valley, one discovery of oil in a previously known gas sand and five or six extensions of some importance. Geological Section The columnar section in south Arkansas (Fig. 1, p. 317) also applies in north Louisiana, with a few changes noted below. The oldest known formation in north Louisiana is a bed of rock salt. Except on salt domes, only one well at Rodessa has been drilled into this salt, but it has been penetrated by a number of wells in south Arkansas. Salt domes have been discovered near Vicksburg and Hattiesburg, Miss., and a deep well in Limestone County, Texas, has drilled into rock salt. In Louisiana the distance between the "interior salt-dome basin" and a salt dome of the "Gulf Coast salt basin" is hardly 60 miles. In short, evidence is accumulating to indicate that all of Louisiana, with the possible

Jan 1, 1938

By George A. Johnson, Leon H. Banks

The Missouri-Kansas Zinc Corpn., operating in the Waco district, 15 miles northwest of .Joplin, Mo., owns large tailing piles made during milling operations of the years 1918-28 by the Butte-Kansas, Acme, and Barnsdall mining companies, whose holdings have been purchased and consolidated under the ownership of the Missouri-Kansas Zinc Corpn. These tailings had been considered too low in value to be worth retreating by the ordinary methods. C. Erb Wuensch, consulting engineer of the Missouri-Kansas Zinc Corpn., noted the difference in the type of tailing from upper-level and lower-level ore. The latter contained hard lime chats. He also found that mill losses had been due to particles of blende on the corners or sides of the chats and to the existence of soft, porous, cellular, lime chats containing varying amounts of blende. He conceived the idea that a quick grind in rolls or hall rnills might change the type of the rnaterial so that jigging could rnake a clean tailing for discard and a partly concentrated product sufficient in blende content to justify the expense of fine grinding in hall mills to free the mineral entirely. A laboratory was equipped with the necessary machines and the writers were assigned the problem of developing a method of retreating the tailings. Laboratory Testing From preliminary drill sampling of each pile was obtained the blende content, the soluble sulfate content, and the general characteristics of the material to he treated. The tailings were a mixture of lime and flint with some shale. Visual examination showed most of the blende to be in the dolomite and very little in the flint, although there were some flint particles with blende on the cleavages. The blende was found as particles on the corners or cleavage faces in one type of chat and in another disseminated in a soft, porous, cellular lime. Because of the porosity of the latter type of chat, the apparent specific gravity, under hindered-settling conditions, is less than that of a solid piece of lime or flint. That it,

Jan 1, 1930

By Richard Moldenke

One of the gravest problems of the iron foundry today is the accumulation of sulfur in commercial scrap and its effect on the castings made therewith. The ordinary jobbing castings today show a sulfur content of 0.18 per cent;, and occasionally as high as 0.22 per cent. The product of the foundry during the war is undoubtedly to blame for this rapid increase and conditions will become worse as the millions of tons of gray-iron castings of the war period return to the foundry in the form of commercial scrap. In the ordinary cupola remelting of pig and scrap, at least 0.02 per cent. sulfur is taken up; often double that amount. The high cost and difficulty of obtaining pig iron during the war period compelled the use of considerable scrap in the mixtures; frequently charges containing 90 per cent. of bought scrap were melted. Naturally the sulfur content of the castings increased. Until the advent of the basic-hearth electric furnace, the only method of holding the sulfur within reasonable limits was to use high percentages of pig in the foundry mixtures. Pig iron seldom contains over 0.05 per cent. sulfur, if well made. With pig iron forming 60 per cent. of the charge and the gates, runners, rejections, and bought scrap the other 40 per cent., the sulfur content of the castings can easily be held down to 0.10 per cent. Pig iron, however, costs more than scrap even when melting loss differences are considered, hence as small a percentage as possible will be used. The recent advance in knowledge of rational melting and the consequent reduction in losses directly due to oxidation of the metal and cold iron, has permitted the acceptance of castings with a much higher sulfur content than formerly. The steel industry also is seeking to determine how high sulfur may go with safety. In the iron foundry, however, there is the danger of a low cupola bed or an unduly retarded air-furnace heat, with the consequent raising of the freezing point of the metal and segregation effects resulting from high sulfur with insufficient manganese. The iron foundryman must, therefore, have a means of correcting his

Jan 1, 1922

By Arthur Dwight

WE NOT have to go so very far back, when measured in actual years, to what may be considered the beginning of the industrial era of the great West, the discovery of gold in California in 1848, just 74 years ago. By a strange coincidence, this event occurred within a few days of the signing of the treaty with Mexico which ceded California to the United States. Needless to describe the mighty wave of humanity that hurled itself toward the setting sun in response to that call. The single thought in every one's mind was gold. The gold as they found it in placers or ledges could be so easily worked, and the product was so readily transportable, and available immediately as money, that practically no attention was paid to deposits of the base metals, in the treatment of which cheap transportation was a paramount con-sideration; consequently little progress was made in anything but gold mining until after the Civil War. The next great step was accomplished when East and West were united by the successful construction of the Union Pacific Railroad from Omaha across the great plains and through the Rockies to meet the rails of the Central Pacific coming eastward across the Sierras. The industrial history of our great West really dates from the day when those two hands of steel were joined, on the shores of the Great Salt Lake at Prom-ontory Point,. May 10, 1869. That seems a long time ago when we think of the enormous changes that have been wrought since that day, and when we regard the rich empire that has sprung up in that western land. Into the new empire thus made accessible, by this first thread of steam transportation, flocked a new brood of adventurous spirits from the older communities of the East. This way walked Fate; and as she, went, flung far the line of destiny, That bound an untracked continent to brotherhood from sea to sea; That long gray trail of dream and hope, marked mile by mile with graves that keep On every barren hill and slope some stout heart lost in dreamless sleep. Patience and faith and fortitude were willed to it and justified; Stern, homely virtues, plain and rude, eternal as the sky and wide. Nor ever sea-king dared the sea in sterner mood than these who went Strong armed to wrest from Mystery their birthright, half a continent.

Jan 4, 1922