Search Documents

By H. S. Gipson

A process that has come to be known locally as "multistage stabilization" has been developed in the Haft Kel field of the Anglo-Iranian Oil Co. in southwest Iran, for the recovery of casinghead gasoline. It consists in releasing the dissolved gases from the crude by stages, a practice common in many fields, but which, so far as is known, has nowhere been carried to the extent to which it is employed in Iran. It has been in use there for nearly nine years, during which time some 200 million barrels of crude have been handled by the process. This process of gasoline retention consists in preventing the greater part of the casinghead gasoline hydrocarbons (the butanes and pentanes) from ever leaving the crude, instead of allowing them to be vaporized and then recovered from the lighter gases by the usual compression or absorption processes. Its efficiency is fully equal to that obtained by the absorption process; its disadvantage is that it increases the quantities of ethane and propane in the crude sent to the refinery, but with the growing demand for propane this drawback is vanishing. When casinghead gasoline is recovered as a separate liquid in the Iranian fields, it is blended with the crude, as the only outlet is through the refinery, and the crude-oil pipe line offers the cheapest means of transportation. It is under these conditions that the retention of the butanes and pentanes in the crude by multistage stabilization is a most attractive process, possessing as it does the following advantages: (1) extreme simplicity, (2) low first cost, (3) easy installation! (4) practically 100 per cent operating-time efficiency, (5) no operators required, (6) no water or other services required, (7) negligible maintenance, (8) once established, very little routine testing is necessary. The one essential for reasonably efficient multistage stabilization is that the flowing pressures of the wells should be relatively high; i.e., they should not be less than about one-third the saturation pressure of the crude in the reservoir. This is a very general statement, of course, and much depends on the type of crude and its temperature.

Jan 1, 1940

Andes Copper has an old camp and a new camp, both isolated until recent road improvements. The old camp is at Potrerillos and the new one at El Salvador, 25 road ,miles away. The company was incorporated in 1916 and the first mine, concentrator, leaching plant, smelter and town were built in the succeeding twelve years. The first blister copper was poured on January 24, 1927. Economic conditions determined the long development period but the end result was the design and construction of a mining complex that was all of a piece, unlike the piecemeal additions to El Teniente and Chuqui. The mining episode at Potrerillos came to an end in 1960 when the ore at La Mina became exhausted and the new mine, El Salvador was brought in. Both of these ore deposits come within four hpundred feet of the surface and had they been developed within the last five years might reasonably have been brought in as open pit mines. However, that is conjecture, and as it stands the operation at La Mina was so ideal for the mining method selected, blockcaving, it became a classic for the textbooks. On the other hand, El Salvador has turned out to be a blockcaving mine to test an engineer's skill. In mining the copper deposit at Indio Muerto mountain, there are ground conditions of every conceivable type. Tunneling in one section, the back can cave like sized pea gravel and only spiling can hold it; in another heading only the lifters are shot but often the rest of the round will sit down in one piece; elsewhere the bottom squeezes up and closes the drifts; and contrary to all other locations, there are sections where the block can be undercut without support. Today the scope of operations at Andes extends from mining to electrolytic copper. Ore is mined at El Salvador and the concentrator is also situated there. Concentrates pipelined 14 miles to Llanth, the water decanted, and then it is hauled by rail 40 miles and 5500 ft higher to the Potrerillos smelter and refinery. Potrerillos and El Salvador are respectively 90 and 70 miles from the port of

Jan 11, 1969

By Aaron J. Miles, Eugene A. Stepenson

The pressure distribution in a producing oil or gas reservoir has been obtained mathematically in a limited number of special cases where the boundary of the reservoirs are simple geometric figures with the wells conveniently located within them. Using some of the previous work as a basis, it can be proved that a number of additional problems of pressure distribution can be solved by use of soap film. This method is particularly applicable to a reservoir drained by a number of wells, or to a reservoir of irregular shape, or to both. Since this method obtains the pressure distribution, it also establishes the drainage boundaries of the wells. This paper derives the analogy between the equation representing the pressure distribution in a reservoir and the equation of the deflected membrane. It also describes the apparatus and the method of operation. The experimental method is employed to solve a problem whose mathematical solution is known and the results compared. These are found to be in good agreement. The method is applicable to any homogeneous liquid, compressible or incompressible, or to a gas, flowing in a reservoir of uniform thickness, permeability and porosity. The flow state may be either the steady state or the transient state wherein the density or pressure of the fluid in the reservoir declines at a constant rate. PRESSURE-DISTEIBUTION PBOBLEM Fluids encountered in the oil reservoir are compressible and expand and move toward the drilled hole where the Dressure is lowest. The loss of fluid from the reservoir lowers the pressure in the more distant parts of the reservoir, permitting the fluids in these parts to expand and move toward the well. The area around the well affected by drainage is increasing continuously, and the density, pressure, and velocity of flow

Jan 1, 1938

By E. S. Burnett, R. V. Higgins, H. C. Miller

Information obtained from subsurface pressure and ,temperature measurements in oil wells now is recognized as invaluable to geologists, engineers, and operators of oil properties. Available only during the past few years, data resulting from subsurface-pressure surveys in oil wells already have found widespread application in the estimation of reserves and in the planning of comprehensive oil-field development programs. Subsurface pressure and temperature data, together with measurements of fluid volumes produced by individual wells and specific gravities of the fluids, also are included in the fundamental information essential in studying the movement of oil, gas and water through reservoir sands to wells. Heretofore, laboratory findings were relied upon almost entirely for information pertaining to the mechanics of flow of fluids through porous media, because there was no way to check laboratory results with actual performance in underground formations until subsurface pressure and temperature instruments were developed. Laboratory and field experiments now lend themselves to closer correlation—a fact that will accelerate the interpretation of many phenomena that occur when oil and gas flow through reservoir rocks, thousands of feet below the surface of the earth. This paper summarizes the results obtained thus far in a Bureau of Mines study of certain data pertaining to subsurface pressures and production of wells producing oil and gas (and water). For wells that have been studied, flowing naturally under volumetric or hydraulic control, a simple relation has been found between the mass rate of fluid (oil, gas and water) production and the corresponding drop in pressure in the reservoir sand. The equated relation embodies a productivity factor or "index" expressed in terms of mass rate of fluid production per pound drop in pressure through the sands. The equation as developed is an expression of the ability of a well to produce, which permits comparison on a uniform basis of the productivities of different wells. The study shows also that over the range of observed data a productivity factor

Jan 1, 1937

By T. A. Richard

We rejoice that the world-war is ended. We are proud of the part played by the English-speaking peoples—all doing equal honor to the traditions they share in common. One of the compensations for the calamity of the past four years is the fact that the Briton and the American, striving together in the cause of human liberty, have learned to understand and to respect each other. The mother country entered the fight resolutely at the beginning, while yet unready to meet the carefully prepared onslaught of the enemy; then the sons from the overseas dominions rallied to the old battle-cry eagerly and effectively; and last, but not least, the stepsons came from across the Atlantic, speaking the same speech, playing the same game, and fighting in the same clean way. It was a great foregathering of those that use the language of Shakespeare and idealize the principles of liberty for which the friends and associates of Shakespeare stood sponsor three centuries ago.' At a time like this it is pleasant to dwell upon the fact that the liberal Englishmen who organized the Virginia company were the pioneers of self-government on the American continent. The Virginia Assembly, convoked in 1619, was the first example of a domestic parliament to regulate internal affairs on this side of the Atlantic.2 The Governor of Virginia, Sir Edwin Sandys, had been a pupil of Richard Hooker at Oxford and from that political teacher he and his friends had imbibed the idea of combining civil liberty with constitutional order. To this group of large-minded Englishmen, the American colonists owed their liberal charters and their successive triumphs over the royal prerogative. Let it be noted that the American colonists had to deal with James II and George 111, the two smallest minds in the list of British kings. Another historical note, more pleasant to record, is the connection between the two principal groups of American settlers. In 1608, when the Pilgrim fathers, William Brewster and John Robinson, led their Separatist congregation to Holland and there prepared the expedition to America, they were assisted by Sandys and the Virginia Council, who were willing to share their privileges with them. When the Pilgrims set sail in 1620 they had the promise, obtained by Sandys from King James, that they should have freedom of worship,

Jan 1, 1920

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth, W. L. Finlay

Titanium with up to 7.5 pct Al forms single-phase a alloys that are work hardening, not heat treatable, and ductile as welded. The high aluminum Y phase alloys are not usefully ductile, despite their low hardness, but they have excellent oxidation resistance and hot hardness. LITTLE has been published on the effect of aluminum on the mechanical properties of titanium, despite the fact that two of the first four commercial alloys released by titanium alloy producers contained aluminum as an important alloying ingredient. These were both a-ß type alloys, one containing 4 pct A1 and 4 pct Mn and the other containing 3 pct A1 and 5 pct Cr. However, neither of these alloys reflects the true alloying nature of aluminum, since each contains important amounts of the ß-stabilizing addition, manganese or chromium. In a previous publication on the constitution of Ti-A1 alloys,' the authors showed that aluminum had a high solubility in a titanium and was strongly a stabilizing in nature. About 25 wt pct A1 is soluble in a titanium at room temperature. With as little as 5 pct added aluminum, the a transus temperature is increased from 882" to 970°C, and the correspond- ing ß transus to 995°C. The first intermediate phase in the Ti-A1 system is the ordered face-centered tetragonal TiAl phase, which extends from 34 to 46 wt pct Al. The present paper presents hardness data over the entire titanium-rich region of the system, through the TiAl phase, and mechanical property data on the alloy range capable of being fabricated. Methods of Investigation The materials used and general preparation of alloys, as well as experimental techniques used in the investigation of Ti-A1 alloys, have been adequately described.' Briefly, the preparation consisted of arc-melting the desired amount of high purity aluminum (99.99 pct purity) and iodide titanium (maximum hardness 100 Vickers, as deposited) together on a water-cooled copper hearth under a partial pressure of argon. The resulting button ingot was of such form that it could be fabricated without further treatment. All work was done using ingots weighing 10 to 15 g, which were hot-rolled to strip form whenever possible. Tensile samples were 3.25 in. long, 0.5 in. wide, and 0.040 in. thick, with a reduced section 1.25 in. long by 0.250 in. wide. The gage length used was 1 in. Electrical strain gages mounted on the

Jan 1, 1954

CHUQUICAMATA, as the Chile Copper Company's mine is known, has the largest developed deposit of copper ore in the world. Indeed, it is improbable that its equal will ever be found. The Union Miniére du Haut Katanga, operating in the Belgian Congo, may some day surpass Chuquicamata in the total amount of copper produced; or one of the companies developing the rich copper region of Northern Rhodesia may ultimately outdo it. But in each instance, the ore will come from a group of mines separated by 80 miles or more; whereas the deposit at Chuquicamata is one vast integral mass containing as a minimum probably 1,000,000,000 tons of ore, averaging better than 8.5 per cent copper, and as a maximum-well, most any reasonable figure might err on the low side. Utah Copper approaches Chuquicamata more nearly than any other in tonnage of exploitable ore; but Utah's ore is less than half as rich. The figure for the aggregate copper content of the reasonably assured ore at Chuquicamata is breath-taking at 50,000,000,000 pounds. Other distinctions has Chuquicamata: It was the first of the Porphyry Coppers to use leaching as the method of treating the ore; its plant cost for producing is lower than that of any of the others, only Braden and Utah being close rivals; and it was worked for its copper long before any of the others. According to an authentic article published in Ingeniería Internacional (May, v 1982) the Incas smelted copper ores from Chuquicamata prior to 1536. Diego de ALnagro, to whom Charles V, King of Spain, generously allotted a one-fourth portion of South America lying south of Cuzco, the Inca metropolis, made an expedition into Chile in 1534. Better known to history, perhaps, is Pizarro, who was awarded the area immediately north, and who proceeded

Jan 1, 1933

By Bernard York, John J. Reed

Mine opening stability was investigated by loading model openings to failure. Eight-inch plaster blocks were cast with small uniform section openings passing through the centers. After curing, the models were jacketed and loaded hydrostatically in a closed vessel. Opening size, shape, and orientation were varied to determine how these factors influence opening stability. THE investigation described in this paper is a continuation of a project begun in 1946 by Bernard York and W. E. Bush. .The experimental method used in the investigation involves the hydrostatic loading of a model mine opening to failure. Most investigators agree that this loading closely approaches actual conditions in very deep mines. The conditions are further idealized by using an essentially isotropic model material. The experiments consist of casting 8-in. plaster cubes, or 8-in. diam cylinders 8-in. long, having a relatively small uniform section hole passing through their centers. After thorough drying, the models are jacketed in a flexible plastic bag and loaded hydrostatically with water in a closed vessel. At about 300 to 500 lb per sq in. pressure the central opening fails. The fracture pattern resulting from opening failure is studied in a plane normal to the longitudinal axis of the opening. The model block is sawed through its center after loading to expose this plane and to eliminate the possibility of end effect. By changing

Jan 1, 1954

By H. Cecil Spicer

THE results described in this article are based on field work conducted during the periods April-May, 1939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation was completed under a cooperative arrangement made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. EARLIER STUDIES Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friedel1 and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly3described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger5 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 8oo ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining Co.

Jan 1, 1941

By M. R. Hatfield, F. J. Vosburgh

In a recent article, it was shown that in the blast furnaces in Germany that are lined with carbon blocks no cooling plates are used, and that shower cooling is employed on the hearth and bosh sections. While one of the authors was in Germany he was told that one furnace was being operated without even the shower cooling on the bosh section, though the hearth section was shower-cooled. In discussion of this interesting situation with a number of blast-furnace operators in this country, it was made clearly and promptly evident that shower cooling was very unpopular, probably because of its messiness and its ineffectiveness. Both of the causes for the dislike of shower coolings are reasonable ones. Shower cooling can be and frequently is messy, but the present cooling of blast furnaces leaves much to be desired on that score. Shower cooling is ineffective as compared with plate cooling, so far as its usefulness in keeping the bricks cool enough not to melt or fall to pieces is concerned. However, the introduction of carbon linings changes the situation. No one is concerned with keeping a carbon lining cool, for no temperature in the blast furnace has any effect on carbon, which is just as stable at 3000°F. as it is at 70°F. The only concern is for the shell—to keep it cool enough for safety and comfort— and for that shower cooling is sufficient. Of course, with only the shell to cool, instead of the shell plus all the refractory material, much less water would be required, and the necessity for constant attention to the flow would be lessened, as the hundreds of inlets and outlets would be eliminated. Probably half of the water used in cooling a blast furnace is used for cooling the shaft and tuyeres and the remainder for the bosh and hearth sections. However, in view of the dislike of shower cooling in the United States, and particularly because at least one German blast furnace is operated with no cooling of the bosh section, thought was given to the possibility that a carbon-lined blast furnace might be operated without any cooling of the entire carbon-lined portion. For that reason a series of experiments was performed to determine what might be the temperature of the shell of a blast furnace protected by a carbon lining and operated under varying conditions up to a maximum inside temperature of 3000°F. Experimental Procedure A schematic diagram of the experimental setup is shown in Fig. I and a photograph of the entire assembly in Fig. 2. The heating element was a a tubc nominally 25/8 in. 0.d. by 2 in. i.d. by 30 in., used as a resistor. Power was furnished by a I5-kva. transformer operating

Jan 1, 1942

By J. H. Henderson, J. Naar

The displacement of a wetting fluid from a porous medium by a non-wetting fluid (drainage) is now reasonably well understood. A complete explanation has yet to be found for the analogous case of a wetting fluid being spontaneously imbibed and the non-wetting phase displaced (imbibition). During the displacement of oil or gas by water in a water-wet sand, the porous medium ordinarily imbibes water. The amount of oil recovered, the cost of recovery and the production history seem then to be controlled mainly by pore geometry. The influence of pore geometry is reflected in drainage and imbibition capillary-pressure curves and relative permeability curves. Relative permeability curves for a particular consolidated sand show that at any given saturation the permeability to oil during imbibition is smaller than during drainage. ' Low imbibition permeabilities suggest that the non-wetting phase, oil or gas, is gradually trapped by the advancing water. This paper describes a mathematical image (model) of consolidated porous rock based on the concept of the trapping of the non-wetting phase during the imbibition process. The following items have been derived from the model. 1. A direct relation between the relative permeability characteristics during imbibition and those observed during drainage. 2. A theoretical limit for the fractional amount of oil or gas recoverable by imbibition. 3. An expression for the resistivity index which can be used in connection with the formula for wetting-phase relative permeability to check the consistency of the model. 4. The Iimits of flow performance for a given rock dictated by complete wetting by either oil or water. 5. The factors controlling oil recovery by imbibition in the presence of free gas. The complexity of a porous medium is such that drastic simplifications must be introduced to obtain a model amenable to mathematical treatment. Many parameters have been introduced by others in Iprogressing" from the parallel-capillary model to the randomly interconnected capillary models independently proposed by Wyllie and Gardner3 and Marshall4. To these a further complication must be added since an imbibition model must trap part of the non-wetting phase during imbibition of the wetting phase. Like so many of the previously introduced complications, this fluid-block was introduced to make the model performance fit the observed imbibition flow behavior. THE IMBIBITION MODEL ASSUMPTIONS The following assumptions are common to many two-phase models previously described. 1. The wetting characteristics of the medium are clearly defined. 2. When two fluids co-exist in the medium, the wetting phase will fill the smaller pores and the non-wetting fluid the bigger ones. 3. The pores have a circular cross section. 4. Apparent pore radii are related to the capillary pressure (drainage) by

By M. R. Hatfield, F. J. Vosburgh

In a recent article, it was shown that in the blast furnaces in Germany that are lined with carbon blocks no cooling plates are used, and that shower cooling is employed on the hearth and bosh sections. While one of the authors was in Germany he was told that one furnace was being operated without even the shower cooling on the bosh section, though the hearth section was shower-cooled. In discussion of this interesting situation with a number of blast-furnace operators in this country, it was made clearly and promptly evident that shower cooling was very unpopular, probably because of its messiness and its ineffectiveness. Both of the causes for the dislike of shower coolings are reasonable ones. Shower cooling can be and frequently is messy, but the present cooling of blast furnaces leaves much to be desired on that score. Shower cooling is ineffective as compared with plate cooling, so far as its usefulness in keeping the bricks cool enough not to melt or fall to pieces is concerned. However, the introduction of carbon linings changes the situation. No one is concerned with keeping a carbon lining cool, for no temperature in the blast furnace has any effect on carbon, which is just as stable at 3000°F. as it is at 70°F. The only concern is for the shell—to keep it cool enough for safety and comfort— and for that shower cooling is sufficient. Of course, with only the shell to cool, instead of the shell plus all the refractory material, much less water would be required, and the necessity for constant attention to the flow would be lessened, as the hundreds of inlets and outlets would be eliminated. Probably half of the water used in cooling a blast furnace is used for cooling the shaft and tuyeres and the remainder for the bosh and hearth sections. However, in view of the dislike of shower cooling in the United States, and particularly because at least one German blast furnace is operated with no cooling of the bosh section, thought was given to the possibility that a carbon-lined blast furnace might be operated without any cooling of the entire carbon-lined portion. For that reason a series of experiments was performed to determine what might be the temperature of the shell of a blast furnace protected by a carbon lining and operated under varying conditions up to a maximum inside temperature of 3000°F. Experimental Procedure A schematic diagram of the experimental setup is shown in Fig. I and a photograph of the entire assembly in Fig. 2. The heating element was a a tubc nominally 25/8 in. 0.d. by 2 in. i.d. by 30 in., used as a resistor. Power was furnished by a I5-kva. transformer operating

Jan 1, 1942

By Bailey Willis

It is proposed to present some of the results of observation of the geologists of the Appalachian division during the past seven years, and of experimental study during the past three years, on the subject of structural geology in the Appalachian Province. The article must be brief, even at the risk of obscurity; but a more complete and fully illustrated paper will appear in the Thirteenth Annual Report of the United States Geological Survey. Certain Facts. The following facts are first to be taken account of: From the Cambrian age to the Carboniferous there existed a conti nent stretching southeast from the present range of the Blue Ridge, covering what is now eastern Pennsylvania, New Jersey, eastern Vir ginia, North and South Carolina and eastern Georgia, with some un known part of the present Atlantic ocean-bed. Northwest from this continent lay a sea, reaching to the west and north of the Mississippi. Sedimentary deposits derived from the land accumulated with or ganic remains, in the sea; the greater part fell in a narrow zone along the shore, the remainder spread in a comparatively thin sheet over the bottom of the Mediterranean of North America. The resulting strata measure, near Mauch Chunk, Pa., 30,000 feet; over much of Pennsylvania, 20,000 to 25,000 feet; over eastern Tennessee, Georgia and Alabama, but 10,000 to 15,000 feet. The stratified mass, considered with reference to its broad physical char acters, consists of three members: A base of shale and sandstone ; a middle of limestone, 2500 to 6000 feet thick—a stratum probably not equalled in the world for uniformity of character and massive ness; and a top of shale and sandstone, 5000 to 23,000 feet thick. This mass has been folded. In a zone 900 miles long and 50 to 125 miles wide, the strata exhibit such attitudes and relations as could result only from a force of compression acting from north west or from southeast, or from both directions. Our problem is :

Jan 1, 1893

By Jack A. Kanz, Samuel R. Shortes, E. C. Wurst

Zinc diffusion into GaAs from the vapor phase through reactively sputtered SiO, films Izas been inrestigated for various zinc pressures at 1000"C. Diffusions were carried out in evacuated quartz ampules with elemental zinc and with various Zn-Ga alloys. Sputtered films have proved effective in lowering surface concentrations and preventing surface deterioration during diffusion. Approxin.ate complenzentary error-function impurity distributions were found when surface concentrations were reduced to approximately 3 -—4 x 10" atoms cm'3 or less with dilute zinc sources or by diffusion through SiO, films. Zinc difhsions in GaAs tlzrough SiO, films produced more planar diffusion fronts than were observed with uncoated zuafers under identical conditions. A) Surface Deterioration During Diffusion. Device technolorn-- in compound semiconductors has been hampered by several difficult problems not normally encountered with silicon and germanium. 111-V and 11-VI compound semiconductors generally have volatile constituents at temperatures used for diffusion. To achieve specific junction depths in reasonable lengths of time, or to obtain particular impurity distributions and doping levels, it is often necessary to use temperatures which cause surface deterioration and erosion of the wafer. The resultant surfaces are generally unsuitable for devices. The type and extent of surface damage depends to varying degrees on the particular environment of diffusion and on the particular impurity in question. The most common type of deterioration results from simple dissociation of the gallium and the arsenic during diffusin.' The deterioration process is significantly enhanced by thermal gradients in the diffusion zone, usually resulting in vapor transport and condensation at the cooler portion of the system. The resulting damage sometimes appears as a general haziness over the surface or an array of pyramidal etch pits characteristic of the particular orientation. Occasionally, erosion of the surface occurs uniformly over the wafer so that surface loss is not readily apparent. Workers in GaAs usually resort to the sealed-ampule type of diffusion system3"5 rather than the more conventional open system used for silicon and germanium. Another type of deterioration results from direct interaction of the impurity with the surface. The form of deterioration may vary from surface alloying, as in the case of zinc, to direct chemical attack and vapor transport of the reaction products, as in the case of sulfur. Surface alloying with zinc occurs at higher temperatures and source vapor pressures.4 The process is largely controlled by the amount of free gallium on the surface of the wafer in equilibrium with the arsenic lost to the system. The group-VI elements, sulfur, selenium, and tellurium, are commonly used donor impurities for gallium arsenide. These elements are characterized by high vapor pressures and high chemical

Jan 1, 1964

By A. G. H. Anderson, Eric R. Jette

During the period from 1910 to 1920, there was a lively interest in the subject of grain growth and many papers were published, followed by interesting discussions. Questions dealing with the fundamentals of grain growth—why and how it occurs—were treated in papers by Howe,' .Jeffries,² Sauveur,² Chappell,4 Beilby,5 Mathewson and Phillips,6 Mc Adam,7 Carpenter and Elam,8 Stead and Carpenter,9 Ruder,l0 as well as others. Since that decade, much indeed has been done regarding the practical control of grain size, and it is now possible to order material having a size sperified in the American Society for Testing Materials classification. Also, one hears the term "spliced boundaries" used in connection with certain tungsten lamp filamentsl1 wherein it is important to prevent "sagging" between consecutive turns of the helix.12 This practical use of a certain knowledge as to the things that influence or even control grain growth should not be taken as an indication that the subject has been thoroughly explored and that nothing more can be learned from fundamental studies. It is with this thought in mind that a report of some observations and experiments on abnormal grain growth is believed justified. Abnormal grain growth is met with in heat-treating high-carbon steels in the austenitic range,'? in the hardening treatments of high-speed steels,14'15 and in the low-temperature annealing of strained low-carbon steels as in sheet and wire material. Entirely aside from these instances of exaggerated grain growth, which some might consider as freakish, it is thought that abnormal growth is simply a case where the growth forces and the forces tending to prevent growth are almost, but not quite, evenly balanced. Information relative to grain-growth characteristics in general may be obtained from a study of abnormal growth conditions, which may be looked upon as vantage points. Reflection will show at once that if growth forces are great in comparison to inertia or resistance to growth, many crystals start to grow and, for that reason, none becomes very large, whereas if inertia is

Jan 1, 1938

By Mohamed Mortada

A practical analytical method is developed in this paper which provides the practicing reservoir engineer with a handy method for analyzing oilfield interference problems. The procedure employed entails the principle of superposition of individual eflects. A set of charts has been developed and can be used to evaluate the individual effects. The charts represent non-steady state pressure distribution in an extensive aquifer due to a constant rate of production from an oilfield which can be approximated by circular geometry; they are constructed from solutions to the diffusivity equation considering a circular sink as distinguished from a point sink. The solutions are obtained partially from mathenlatical considerations and partially from analog and digital computations. By virtue of the method of images, the charts can be used also to treat the case of production near a fault. In addition, provisions are made for treating oil fields, which are produced by partial water-drive. Treating an actual field case is deferred to a subyequent writing; however, illustrative example is presented to demonstrate the method of application. The pressure distribution in linear and limited radial aquifers is currently under study. INTRODUCTION With the increasing difficulty of discovering new oil reserves, attention is necessarily focused on the efficient development and production of existing reservoirs. Efficient production depends on the availability of reliable means for predicting the pressure-production behavior of oil fields. The prediction is usually performed by analytical methods or computers. Analytical methods are often limited to systems which can be approximated by simple geometry. However, analytical methods have the distinct advantage of being readily performed without special equipment. Analog and digital computers lend themselves to a variety of problems, but are not always locally available and consequently their use is limited. One particular situation in which analytical techniques are needed involves studies of multiple, water-drive oil fields sharing a common aquifer. Such oil fields are in hydrodynamic communication. Therefore, production from any of the oil fields is accompanied by a pressure decline which is transmitted through the aquifer to the other oil fields and manifested as pressure interference. The rate of propagation of the pressure decline is such that the pressure may be significantly reduced many miles away from a producing pool. An example of pressure interference is found in the Woodbine formation in East Texas. There. a dozen or more pools, including several of major size, draw on the Woodbine formation for water drive. The pressure in the water-bearing portion of the formation has been significantly reduced over an area of several thousand square miles. This reduction of pressure has been such that when the Hawkins pool was discovered in 1940, the pressure in it had already been reduced 280 psi below the initial value in the aquifer. This resulted from prior production from other Woodbine sand pools, including, in particular, the East Texas field some 20 miles to the east of Hawkins.' The above example indicates that the interference effect can be significant and should be taken into con-

Jan 1, 1956

By J. R. Long, T. R. Graham, R. G. Feustel, R. S. Dean

THE comprehensive study of the copper-manganese-zinc alloy system in the Bureau of Mines Laboratories has so far been principally concerned with alloys that lie within the alpha solid solution field of the system. Two regions, one centering about 65 per cent copper, 10 manganese and 25 zinc, and the other centering about 70 per cent copper, 20 manganese, 10 zinc, have been carefully examined.1,2 These have indicated that when the alloys are made with electrolytic manganese considerable amounts may be readily introduced and that the strength and hardness are increased without excessive losses in ductility. In the course of the work of establishing the limits of the alpha solid solution range,3 enough of certain of the alloys was prepared to permit determination of their physical properties at a future date. The 60 per cent copper alloys concerned here are part of that series. They cross through the alpha field and into the adjacent alpha plus beta and alpha plus X fields, and are of interest because they offer some information on the effects of manganese on alloys lying in these fields. COMPOSITION AND FABRICATION OF ALLOYS The chemical composition of the alloys involved is given in Table I. They were intended to contain 60 per cent copper with manganese increasing from 5 to 25 per cent in 5 per cent steps and zinc decreasing [ ] from 35 to 15 per cent. The analyses are so close to the intended composition that the alloys will be referred to hereafter by their nominal compositions. They were finished into sheet by cold-rolling and intermediate annealing procedures calculated to produce sheet 1/16 in. thick, cold-reduced by 20, 40, 60, and 80 per cent in thickness. Physical properties were determined on standard flat tensile specimens with 4-in. gauge length, although the test gauge section used was 2 in. The properties were obtained on cold-worked material and on material annealed at temperatures ranging from l00° to 1500°F. after 60 per cent cold reduction. Since an annealing temperature of 1200°F.

Jan 1, 1946

By W. L. Phillips

The plastic properties of lithium fluoride and magnesium oxide under compression were investigated in the temperature range 25° to 1000°C. At the higher test temperatures, the critical resolved shear stress and the rate of work-hardening of both materials decreased. At the same time, the number of stress lines decreased and the individual stress lines became wider. The density of dislocations decreased for a given strain the higher the test temperature for lithium fluoride. The decrease in the critical resolved shear stress as a function of temperature could be fitted by the equation 7 = Toe-KT. THE influence of temperature on the stress-strain curves of a variety of metal single crystals has been studied for a wide range of temperature.1"5 In general, it has been found that both the critical resolved shear stress and the rate of work-hardening decrease rapidly with increasing temperature and fall to a value of essentially zero well before the melting point is reached. AS the test temperature is increased, the density of slip lines has been found to decrease, while the width of the individual lines increases. Recently, Gallagher,' Graf et al.,7 and Pate1 and Alexander8 have found that single crystals of germanium and silicon, which have a covalent bond, can be plastically deformed at elevated temperatures. In compressing germanium it has been found that the strain-hardening coefficient decreased very rapidly as the temperature was increased. The coefficient did not tend to zero, however, as the melting point was approached. The plastic properties of ionic crystals at elevated temperatures have not been extensively investigated. In the only work previously reported Tamman and salge9 and Theile10 have shown that the yield point of sodium chloride single crystals tested in tension and compression decreased slowly with increasing temperature, falling to zero at the melting point. As the temperature was increased, they found a substantial increase in the amount of plastic deformation that could be sustained before fracture; and at temperatures above 400°C in tension tests there was an obvious necking which produced local extensions of up to 3000 pct. The purpose of the present work is to extend the knowledge of high-temperature deformation to the ionic crystals, lithium fluoride and magnesium oxide. The following were investigated: 1) The gross shape of the stress-strain curve at several temperatures. 2) The change in the critical resolved shear stress as a function of temperature. 3) The appearance of slip bands and the density of dislocations as a function of strain and temperature. EXPERIMENTAL TECHNIQUES The lithium fluoride and magnesium oxide used in this investigation were purchased from the Harshaw

Jan 1, 1961

By A. H. Daane, B. J. Beaudry

The Sc-Ti system was studied by thermal, metal-lographic, and X-ray methods. Scandium was found to transform at 1334 °C from a (hexagonal) to ß which was concluded to be bee since a continuous series of solid solutions is formed between ß scandium and ß titanium at elevated temperatures. There is a minimum in the solidus at 51 wt pet Ti and 1300°C, a monotectoid at 1050°C and 49 wt pet Ti, and a eutectoid at 875°C and 91.5 wt pet Ti. The maximum solubility of titanium in a scandium is 13.5 wt pet at the monotectoid temperature, while the maximum solubility of scandium in a titanium is 6.5 wt pet at 875°C. SCANDIUM, a member of Group 111 A of the periodic table, and now called a rare-earth metal,' has become of interest recently due to its low density (2.99 g per cc) and relatively high melting point (1539°C).Spedding,' et al. have described a method of preparation of pure scandium metal and have made a study of its basic properties. Since scandium is approximately 10 to 12 pet smaller in at. diam than the other rare earths while its electronegativity and valence are the same, a knowledge of its alloying behavior in contrast to these elements should be very helpful to fundamental alloy theory. Since scandium is quite scarce and difficult to prepare in pure form, its use as a structural material by itself seems quite unlikely. However, its use in special cases as an alloying addi- tive to other low-density materials is a possible application; the Sc-Ti system was chosen for this reason and for others of fundamental interest. Scandium was suspected of having a high temperature bee form as do some of the other rare-earth metals.3'4 Since titanium has a high-temperature bee form, a continuous series of solid solutions at elevated temperatures between ß scandium and ß titanium would prove the existence and structure of the high-temperature form of scandium. The existence of a continuous series of hexagonal solid solutions at room temperature was predicted by Burkhanov and Savitskiy,5 but Hias shown to be incorrect in early X-ray studies. EXPERIMENTAL METHODS Materials. The metals employed in this investigation were crystal bar titanium and distilled scandium prepared by the method described by Spedding,2 et al. The major impurities are listed in Table I in PPm. Alloy Preparation. All the alloys examined were initially formed in a nonconsumable electrode are-melting furnace under an atmosphere of purified helium or argon. A curve based on the observed weight loss of 0.6 pet* when titanium was melted

Jan 1, 1962

By Eric R. Jette, A. G. H. Anderson

During the period from 1910 to 1920, there was a lively interest in the subject of grain growth and many papers were published, followed by interesting discussions. Questions dealing with the fundamentals of grain growth—why and how it occurs—were treated in papers by Howe,' .Jeffries,² Sauveur,² Chappell,4 Beilby,5 Mathewson and Phillips,6 Mc Adam,7 Carpenter and Elam,8 Stead and Carpenter,9 Ruder,l0 as well as others. Since that decade, much indeed has been done regarding the practical control of grain size, and it is now possible to order material having a size sperified in the American Society for Testing Materials classification. Also, one hears the term "spliced boundaries" used in connection with certain tungsten lamp filamentsl1 wherein it is important to prevent "sagging" between consecutive turns of the helix.12 This practical use of a certain knowledge as to the things that influence or even control grain growth should not be taken as an indication that the subject has been thoroughly explored and that nothing more can be learned from fundamental studies. It is with this thought in mind that a report of some observations and experiments on abnormal grain growth is believed justified. Abnormal grain growth is met with in heat-treating high-carbon steels in the austenitic range,'? in the hardening treatments of high-speed steels,14'15 and in the low-temperature annealing of strained low-carbon steels as in sheet and wire material. Entirely aside from these instances of exaggerated grain growth, which some might consider as freakish, it is thought that abnormal growth is simply a case where the growth forces and the forces tending to prevent growth are almost, but not quite, evenly balanced. Information relative to grain-growth characteristics in general may be obtained from a study of abnormal growth conditions, which may be looked upon as vantage points. Reflection will show at once that if growth forces are great in comparison to inertia or resistance to growth, many crystals start to grow and, for that reason, none becomes very large, whereas if inertia is

Jan 1, 1938