Search Documents

By M. E. Wadsworth, C. H. Pitt

Nickel corrosion in sulfuric acid solutions at elevated temperatures and oxygen wer-pressures was imestigated. Weight loss was 1inear with time and varied directly with oxygen concentration. Independent variation of the possible active species in solution indicated that the undissociated sulfuric acid molecule plays an important part in the corrosion mechanism. The rate determining step was considered to be the adsorption of oxygen on a site containing adsorbed H2SO4. THE tendency for a metal to go into solution depends on a number of factors some of which are: 1) the position of the metal in the electrochemical series; 2) the type and concentration of corroding species in solution; 3) the concentration of oxygen in solution; 4) the type of film formed at the liquid-metal interface; and 5) the physical state of the metal. The corrosion of a metal in an aqueous solution may be considered to be a heterogeneous reaction that occurs at the liquid-metal interface. The reaction is generally considered to occur as a result of electrochemical potential differences within the system. Little work has been published in the literature concerning the corrosion of pure nickel. A great deal has been publistled dealing with the experimental and theoretical aspects of the over-all corrosion process. Evans,1 Uhlig,' and recently Todt 3 and Tomashoff,4 have published books which review the results of experiments which have been conducted on corrosion, and have developed some of the basic ideas of the more widely accepted theories of corrosion. Friend5 states that. nickel does not readily discharge hydrogen from any of the common nonoxidiz-ing acids and that a supply of some oxidizing agent is necessary for appreciable rates of corrosion. He further notes that at temperatures between atmospheric and close to boiling, corrosion rates tend to vary with concentration, temperature, and aeration in acid concentrations up to 25 pct. Whitman and Russel6 studied the effect of dissolved oxygen on a number of metals in acid solutions and found that oxygen accelerates the rate of corrosion of nickel in sulfuric acid. Flowers and Kelley7 in studying the action of dissolved CO, on electroplated nickel postulated that nickel dissolves as NiHCO3 in the presence of CO, and air. It was found that oxygen was necessary for corrosion to take place and that the rate increased with increasing amounts of oxygen in solution. Flowers and Kelley attributed the oxygen effect to cathodic depolarization. MacGillavry, Rosenbaum, and wensson' determined metal solution potentials of nickel in various electrolytes. They found that nickel has no tendency to corrode in alkaline solutions in the presence or absence of air. In acid solutions in the presence of air, metal solution potential increases in the order of 1/2 v were observed. This increase was attributed to probable chemisorption of oxygen on the nickel surface and the corrosion mechanism suggested was the interaction of H+ ions with the nickel oxide formed at the surface. Delahay9 observed the reduction of oxygen on various metals. A polarograph was used to measure the course of the reaction. With some metals hydrogen peroxide was produced as an intermediate compound. However, nickel was not considered to be a hdrogen peroxide producer. Van Rysselberghe 10,11 and associates attributed the accelerating effect of carbon dioxide on the corrosion process to the presence of percarbonic acid produced in solution reacting with the hydrogen peroxide. The percarbonic acid can be reduced at less negative potentials than hydrogen peroxide and as a result accelerates the reaction. EXPERIMENTAL Since a complete description of the apparatus used can be obtained elsewhere,12'13 no attempt will be made here to describe the equipment other than to note that it consisted essentially of an autoclave unit from which samples could be withdrawn periodically without disturbing the interior state of the autoclave. A titanium autoclave liner was used to protect the autoclave from the solution.

Jan 1, 1961

By G. R. Speich

A cellular precipitation reaction in which cells consisting of an Ni3Ti (DO24) phase and austenite are formed has been studied in an austenitic Fe-30 Ni-6 Ti alloy. The variation of the growth rate and interlamellar spacing of the Ni3Ti cells with temperature has been determined m the range 400" to 975°C; the interlamellar spacing is proportional to the degree of undercooling; the growth rate can be expressed by an equation of the form G = K?T)2 exp(-Q/RT). The habit of the Ni3Ti lamellae is (001)Ni3Ti (111)y;[010]Ni3T2 [010]y. An almost perfectly coherent interface is formed between Ni3Ti lamellae with this orientation rela -tionship and the intervening austenite. This first Ni3Ti cellular product is subsequently consumed by a second cellular reaction of much coarser spacing. CELLULAR precipitation reactions have been studied in copper-base,1,2 Au-Ni,3 pb-sn,4 and iron-base ferritic5,6 solid solutions, and this mode of precipitation has been treated theoretically by smith," Turnbull,8,9 cahn,10 and more recently by bohm.11 In the case of substitutional austenitic iron-base alloys little or no data are available, Cellular precipitation reactions are well known in austenitic nickel-base alloys12,13 but usually these reactions do not proceed to completion because of general precipitation occurring in the matrix, and they have not been studied in detail. Precipitation from an austenitic Fe-30 Ni-6 Ti alloy was studied as part of a larger investigation of the mechanisms of precipitation from substitutional iron-base alloys. This alloy, austenitic at high temperatures, decomposes at lower temperatures by a double cellular precipitation reaction. The first decomposition product consists of alternate lamellae of an Ni3Ti(DO24) phase and austenite. The reaction proceeds to completion, consuming all of the original austenite. This first cellular product is subsequently consumed by a second cellular reaction of much coarser spacing. The first cellular reaction was studied in detail by light and electron microscopy, hardness measurements, and by X-ray and electron diffraction. Interlamellar spacings and growth rates were measured during isothermal aging in the range 400" to 975°C. The orientation relationship between the Ni3Ti and austenite lamellae was determined and indicates that an almost perfectly coherent interface exists between the two phases. This first Ni3Ti cellular reaction is of particular interest because it occurs over such a wide temperature interval. This allows cellular growth rates and interlamellar spacing data to be obtained for much larger degrees of undercooling than reported hitherto. MATERIALS AND EXPERIMENTAL PROCEDURE The Fe-30 Ni-6 Ti alloy was prepared from electrolytic iron, Mond nickel shot, and sponge-purity titanium* by vacuum melting in a zirconia crucible

Jan 1, 1963

By R. J. Weege, A. W. Schillinger

Conventional underground mapping methods and diamond drilling are being applied in a study to determine the nature of the copper ore occurrences near the footwall of the Osceola lava flow top, commonly referred to as the Osceola Amygdaloid. The work to date suggests that structures formed by relatively impermeable barriers, created by flowage and injection of still-molten lava from the interior of the flow into the solidified, brecciated crust, acted as the ore receptacles. Ascending hydrothermal fluids traveling near the footwall contact were trapped and confined in these barriers which retarded the direct upward movement of the ore fluids and caused deposition of copper. Oreshoots located near the footwall appear to have been formed spatially independently from the hanging-wall oreshoots by fluids traveling simultaneously, but along different channelways. The barrier concept, as advanced by earlier writers to explain the concentration of the ore-bearing fluids into broad shoots constituting entire ore bodies, is found to be equally as applicable for the localization of smaller oreshoots within the Osceola ore body. Recently, the Calumet Division of Calumet and Hecla, Inc. completed the unwatering of the old mine workings on the Osceola amygdaloid. Two shafts were subsequently reactivated and mining commenced on the Osceola lode after an idle period of over 20 years. Early in 1961, the Calumet and Hecla Geological Dept. was assigned the task of locating additional reserves. Accordingly, an intensive mapping and underground diamond drilling program was initiated. Except for a very few years following the first mining on the amygdaloid, the Osceola lode had never been a high grade producer. It was, therefore, recognized from the onset that a concentrated effort would have to be made by the mining, milling, and geological departments to insure success of the project. Company reports contained many references to ore that had been located near the footwall of the Osceola amygdaloid. Information concerning the grade of this ore was meager, but it was known that at least some was very rich. In contrast to ore that occurred near the hanging-wall, however, the footwall copper did not appear to have a systematic distribution and a large amount of poor rock had to be removed in developing this ore. This, of course, resulted in high development costs and discouraged any extensive mining of footwall ore. The possibility of more continuity than had previously been suspected was recognized by other workers, in particular Dr. T. M. Broderick, formerly Chief Geologist of Calumet and Hecla, who suggested attempts be made on a trial basis to follow the footwall contact with the main development drift. As most mining was done on the Osceola lode before a geological department had been established by the company, and almost all of these openings are now caved, very little information concerning the geology of footwall ore was available. It was, therefore, decided that the first step in the exploration program would be to become familiar with footwall ore occurrences by mapping the geology as the openings were driven. It was possible that a mapping program would reveal the features that controlled the localization of the ore. Furthermore, if it could be shown that footwall ore was more continuous, or if its distribution was more systematic than generally believed, it would be possible to produce a high grade ore that could be blended with the lower grade hanging-wall ore. In connection with the geological program, the Michigan College of Mining and Technology Geophysical Dept. under the direction of Professor Lloyal Bacon, is making a geophysical study of the problems of locating footwall ore by electrical methods. GENERAL GEOLOGY OF MICHIGAN NATIVE COPPER DEPOSITS The native copper deposits of Michigan are located in Keweenaw, Houghton, and Ontonagon Counties. The host rocks are Keweenawan in age and are comprised of interbedded sediments and lava flows which form a belt two to four miles wide and over one hundred miles long. These rocks form part of the south limb

Jan 1, 1962

By C. N. Reid

Slip-line studies on deformed chromium single cvystals showed the usual bcc behavior. At room temperatuve, cross slip was prevalent—slip was not confined to a given plane, but the slip direction was (111). At -10O0K, slip occuvred on (110) planes, twins on(112) planes, and cleavage on (1001 planes. A single-crystal tensile specimen with an axis close to [011] showed a pronounced yield drop and high strain rate sensitivity which zclere used to derive relevant parame tevs in a dislocation dynamics treatment. Transmission electron microscope studies confirmed the existence of (110) slip planes and showed ecidence of loops punched out by precipitates and of grown-in dislocations promoting tangling. OF recent years experimental studies have been made of the deformation characteristics of single-crystal molybdenum and tungsten, but very little has been published on the behavior of single-crystal chromium. During a study of the mechanical properties of chromium, single-crystal studies were made which have already been partially described.&apos; However, additional information was generated which was not directly relevant to the main theme of Ref. 1, and, therefore, was not reported. In view of the need for complete documentation of deformation modes, the experimental observations made on the deformation of single-crystal chromium are summarized here, together with an electron-microscope study of the associated dislocation structures. It was found that, in terms of the deformation modes, chromium is a conventional bcc metal, showing a very pronounced yield-point phenomenon. Further, it was found that the flow strength of these crystals is very sensitive to the strain rate. Finally, the crystals were observed to contain many unidentified precipitates, which often were associated with prismatic dislocation loops. EXPERIMENTAL METHODS Single crystals were grown from rods of wrought chromium by the method of zone annealing. Rods of "1/4in.-diam were supported vertically in an argon atmosphere while an induction coil was moved up the rod at 1 in. per hr. The power was adjusted to just below that required for melting, and the process produced single crystals in about 30 pct of the rods used. The orientations of the crystals, in general, lay near [011] and are summarized in Fig. 1. Before this treatment, the wrought material contained 35 pprn C, 68 ppm O, and 12 ppm N.* An analyzed single crystal *Usual metallic impurities found in iodide chromium are: Al, 5 ppm; Ca, A ppm; Cu, 2 ppm; Fe, 75 ppm; Yg, 0.5 ppm; Yn, < 3 ppm; Mo, < 3 ppm; Ni, 4 ppm; Si, < 20 ppm; Ti, < 1 ppm; V, 4 ppm; Zr, < 3 ppm. contained 10 pprn C, 79 ppm O, and 50 pprn N. Tension and compression specimens were shaped from the crystals by mechanical grinding, followed by the electrolytic removal of about 0.010 in. from the surface in a perchloric/acetic acid bath. All specimens had a gage length of 0.75 in., and tension specimens had a diameter of 0.100 in., while that of the compression samples was 0.200 in. Mechanical tests were carried out at a rate of 1.3 pct per min, and temperatures below 0°C were attained by means of a nitrogen cryostat similar to that of Wessel.2 EXPERIMENTAL RESULTS Modes of Deformation. In addition to the tensile properties of these crystals, which are described in Ref. 1, deformation markings on the surface were studied. Crystals A and F, Fig. 1, were deformed in tension at 300°K to 10 and 16 pct strain, respectively. The surfaces contained visible slip lines, about 1 C( apart, composed of both straight and wavy segments. They did not define a single plane, and so determination of the slip plane was not possible. However, the slip direction was deduced by comparing the axial orientations of the crystals before and after deformation. Fig. 2 is representative, and shows that the axis ro-

Jan 1, 1968

By G. Wakefield, A. H. Daane, D. H. Dennison, F. H. Spedding

Preparation of pure scandium metal was accomplished by calcium reduction of the fluoride by two methods; a low-temperatzdre alloy process and direct reduction with subsequent distillation of the product. The following properties were determined: melting point: 1181OK; boiling point (calculated): 3000°K; lattice constants at 298°K (hexagonal lattice): a = 3.308 * 0.001 A, c = 5.267 * 0.003A; calculated density at 298°K, g per cm3: 2,990 + 0.007; electrical resistivity, ohm-cm: 299°K, 66.6 ± 0.2 x 10 -6; 373oK, 77.4 * 0.2 x 10 -6; thermal coefficient at 299°K, ohm-cm per deg: 5.4 X x; heat of sublimation at 298°K, kcal pel- mole: 80.79. The vapor pressure was determined as a function of temperature between 1505o and 1748°K, with the data fitted to a straight line shielding the equation: Log Pmm = -1.718 X 104/ToK + 8.298. SCANDIUM, element number 21, was first discovered by Nilson in 1879 and was recognized as the Ekaboron as predicted by Mendeleff. As it is in group III of the periodic table, the general properties are a little like aluminum and also resemble quite closely the properties of yttrium and the rare-earth metals, in both the metallic and ionic form. Although the earth&apos;s crust contains approximately 5 ppm of scandium (the element is as abundant as arsenic and twice as abundant as boron) it generally occurs so widely distributed that it has earned the reputation of being very rare. The one exception to this is the mineral thortveitite, which has been found in Madagascar (20 pct Sc2O3) and in Norway (35 pct Sc2O3). Scandium also occurs in small but distinct amounts in uranium and rare-earth ores; the recent larger scale processing of these materials has made some scandium available from these sources. As with other naturally-occurring monoisotopic elements (except Be), scandium contains an odd number of protons and an even number of neutrons. Scandium metal was first prepared by Fischer and coworkers1 in 1937 by electrolysis of scandium chloride in a molten eutectic mixture of lithium and potassium chlorides, using molten zinc as a cathode and collector of the scandium metal produced. The zinc was removed from the Zn-2 pct Sc alloy by vacuum distillation, leaving a product reported to be 94 to 98 pct Sc, with the main impurities being iron and silicon. They reported a melting point of 1400° C for this material. Scandium has also been prepared by the reduction of scandium chloride with potassium metal in a glass apparatus by Bommer and Hohmann in 1941,&apos; resulting in a mixture of metal and potassium chloride; these workers did not isolate the metal proper, but the X-ray diffraction of the slag-metal mixture showed it to be hexagonal with a = 3.30A, c = 5.45A. petru3, 4 and coworkers have recently reported the preparation of the metal in a compact form by the reduction of either ScF3 or ScC13 with calcium metal and subsequent distillation of the product. This process probably yielded a metal of high purity, but they list no chemical analysis nor do they list any of the properties of their product. Previous related work in this Laboratory has been concerned with the production of yttrium and the rare-earth metals and the determination of their physical properties. Because of its similarity to these metals, scandium is being included in this study. PREPARATION OF SCANDIUM METAL The preparation of yttrium and the rare-earth metals may be accomplished by reduction of their fluorides with calcium metal in tantalum crucibles.5 This process leads to the introduction of tantalum (up to 0.5 pct) as an impurity in the higher melting rare earths, but since the tantalum occurs as dendrites, uncombined with the rare-earth metals, its presence is not objectionable in some cases. The preparation of scandium metal in this manner, however, was found to yield a product containing 2 to 5 pct Ta. To obtain a purer product, the following two methods were developed for the reduction of scandium fluoride with calcium metal: i) a low-temperature process utilizing zinc to form a low

Jan 1, 1961

By E. J. Roberts

Prior to 1916, thickening was an art, and any accurate decision as to what size of machine to install to handle a given tonnage of a specific ore must have been one of those intuitive conclusions, based on both intimate and extensive acquaintance with thick-ners and ore pulps. Then in 1916 "knowledge of acquaintance," became "knowledge about" with the publication of the Coe and Clevenger paper.&apos; The unit operation of thickening had graduated to the status of an engineering science. The fundamental similitude relationships for the two major phases of the operation were defined so clearly that batch tests on models as small as liter cylinders could serve to specify protypes as large as 325 ft in diameter. It is quite apparent from reading the literature that Coe and Clevenger&apos;s contribution is not generally appreciated. In so far as the basic engineering relationships are concerned, the only real advance which has occurred in the 30 odd years which have elapsed since the Coe and Clevenger paper is the recognition of the effect of the rakes on the thickening process. Bull and Darby2 noted this in 1926, and the extensive use of the "gluten type" thickener, in which the effect is magni-fied, bears witness to its importance. Comings3 further verified this effect of the rakes. As a matter of fact, a number of papers show an apparent regression from the Coe paper in that the area determinations are made on the basis of a single test from One concentration of solids. Coe and Clevenger amply demonstrated that this is unsafe, since the controlling zone may be one other than that of the feed dilution. Comings3 neatly demonstrated this without apparently realizing it. Of course there have been significant advances in the application of the operation to industry. Open tray thickeners were introduced to save area; balanced tray thickeners, washing thickeners, and multifeed clarifiers were developed with all of their special hydraulic and mechanical problems. Combinations of all kinds have been introduced, such as combination agitators and thickeners, combination flocculators and clarifiers, combination thickeners and filters. With the establishment of the operation on a firm engineering foundation, installation was facilitated and expansion proceeded. There are still problems, of course, functional as well as mechanical. Sometimes the moisture in the underflow obtained in practice is not as low as is expected on the basis of the test data. Sometimes the underflow is so "thick " that its discharge and subsequent handling requires special attention. Island formation plagues some operators. The use of the thickener as a surge basin and blending tank in the cement industry poses unusual problems. Design of rakes and the drive mechanism must be continually im-proved. Corrosion problems must he overcome. Power requirements for raking the settled solids occasionally is the controlling factor as it was in the case of the all American Canal desilting installation. Other similitude relationships and design problems come into the picture when we enter the field of clarification or nonline settlement. We have an energy dissipation problem in introducing the feed and any models must satisfy the Froude model relationships. Autoflocculation requires detention which involves the same similitude laws that we encounter in the compression zone. Approach to an Exact Science The next step beyond having control of the similitude relationships is to understand the why of these relationships right back up the line to first principles. The ultimate might be that, if given the mineralogical composition of the solids and their size distribution together with an analysis of the suspending liquid, we could calculate the entire thickening behavior of the system. Then we could say we had reduced the operation to an exact science. True it might be more trouble getting this basic analytical data than to make our empirical determinations for area and volume, and we would need an ENIAC to calculate the results, but that does not detract from the desirability of such understanding. Considerable work has been done by the chemical engineers with this end in view. Comings,3 Egolf,4 Work,5 Kam-mermeyer,6 Steinour,7 and others have studied the problem. The writer has no final answer to the thickening story but would like to propose a picture of the mechanics of the two phases of thickening which has been found useful in understanding the subject and which leads to some convenient relationship in treating the compression step and arriving at the compression depth.

Jan 1, 1950

By Leo Horvitz

Microanalysis of near-surface soils for hydrocarbons is the basis of a method for locating gas and oil deposits. To substantiate this technique, evidence of vertical migration of hydrocarbons from petroleum accumulations is presented. Tabulated data relevant to hydrocarbon surveys conducted in several petroleum provinces are included. PEROLEUM and natural gas are composed principally of the saturated hydrocarbons ranging from methane, the lightest, to nonvolatile liquids and solids containing approximately thirty-five carbon atoms. A technique for locating buried accumulations of these hydrocarbons before drilling obviously requires that some of the hydrocarbons leave the deposit and migrate toward the surface of the earth where they may be detected in their original form. Earliest attempts to link near surface hydrocarbons to petroleum at depth were apparently made by Laubmeyer&apos; in Germany and by Sokolov in Russia. These investigators collected samples of soil air from boreholes one to two meters deep and analyzed them for traces of hydrocarbons. They found that soil air over producing areas is richer in these constituents than is soil air over barren areas. Since 1936 work on petroleum exploration techniques of this type has been going on in this country. However, instead of determining hydrocarbon content of soil air collected in the field, investigators analyze samples of the soil itself for adsorbed and occluded hydrocarbons, which are released by suitable treatment and found in larger amounts than are the quantities reported for soil air. Difficulties often encountered in collecting gas samples in the field, moreover, are eliminated when soil is used as the sampling medium. Field Procedure: Sample locations are first surveyed over the area to be investigated. Care is taken to locate the stations at considerable distances from roads, pipelines, drilling wells, and other sources of contamination. The borehole pay be dug with a bucket-type hand auger or with mechanical drilling equipment. Lubricants are avoided in either case. When the desired depth is reached, a sample is brought to the surface, placed in a pint glass jar or can, and securely sealed. Sample containers are carefully labeled and delivered to the analytical laboratory. Generally a satisfactory sampling depth range is 8 to 12 ft. In some regions, however, satisfactory data are obtained from samples collected at much shallower depths. Such is the case, for example, in areas of west Texas where the limestone and caliche near the surface occlude hydrocarbons and prevent their rapid escape to the atmosphere. In carrying out broad reconnaissance surveys in search of large features, considerable time is saved by first taking samples one-fourth to one-half mile apart along profiles about one mile apart. If the analytical data indicate a hydrocarbon anomaly of interest, additional samples are taken to produce a more dense and uniform sampling pattern within the interesting area. This sampling program is particularly adaptable to areas that are sectionized. In areas covered with a network of roads, sampling along these roads facilitates the reconnaissance survey. Actual sampling density used depends upon areal extent of features expected. When flanks of piercement-type domes where accumulations may be only several hundred feet wide are sampled, stations are often no more than 200 ft apart. Analytical Technique: Of the hydrocarbons composing petroleum, only the more volatile would be expected to reach the surface of the earth. The analytical technique, therefore, was developed to determine only those constituents that exert a vapor pressure at room temperature. Actually, in near-surface soils, only a very small part of the hydrocarbons are heavier than pentane. Details of the analytical technique have previously been reported. Only a brief description of the methods will be presented here. A weighed portion of the sample, about 100 g, is first treated with an aqueous solution of copper sulphate and then with phosphoric acid in a partial vacuum. The copper sulphate prevents the reaction of the acid with carbides that may be present because the sample has been contaminated by auger particles. Such a reaction may produce spurious methane. The role of the acid is to decompose any carbonates present, thereby helping to release the hydrocarbons. The carbon dioxide is removed with potassium hydroxide and the flask containing the

Jan 1, 1955

By C. G. Dunn, P. K. Koh

THE primary recrystallization texture in cold-rolled silicon iron, which is the matrix texture for developing the Goss texture or the cube-on-edge texture by secondary recrystallization at temperatures near 900°C,1-5,21 has not been adequately described. Thus from the present available information, it is not possible to explain satisfactorily both the grain-growth selectivity of the matrix and the often observed magnetic torque curve, which itself provides some information on the texture. Also lacking is information on the special annealing texture that develops in this material when the annealing temperature is 1200°C or higher and the rate of rise to temperature is extremely rapid. From the work of May and Turnbull5 and from unpublished work, it was known that isothermal annealing near 1200°C tends to reduce the extent of secondary recrystallization and that a much weaker cube-on-edge texture results if appreciable normal grain growth replaces secondary recrystallization. Koh and Dunn6,7 have obtained additional information on complex primary recrystallization textures from further studies made after normal grain growth. In these instances the initial textures were retained during normal grain growth. A similar result reasonably could be expected in the present study except for the presence of a grain growth ihibitor1-5,8,9.21 and its tendency to allow only a few grains to grow. However, any information on the orientations of grains in the special annealing texture, even if far from representative of the initial matrix texture, would provide useful information on the nature of the matrix texture. In the present texture study the method of Newkirk and Bruce,10 which is based on the methods of Geisler" and Schwartz, 12 is used to obtain a complete (110) pole figure of the primary recrystallization texture. The high-temperature annealing texture is determined simply from the orientations of a large number of selected grains. The kinetic nature of the process that produces the annealing texture is treated elsewhere13 and it is shown that a form of secondary recrystallization with a very high rate of nucleation occurs during rapid annealing at high temperatures. EXPERIMENTAL PROCEDURE Commercial 0.014-in. cold-rolled silicon iron strip (3.16 wt pct Si), prepared by two stages of cold rolling with an intermediate short anneal, was given a decarburizing 3-min anneal at 800°C. Me-tallographic studies indicated complete recrystallization. Short-time anneals at 900° C and at higher temperatures proved that secondary recrystallization had not begun at 800°C, in fact, the short additional anneals were still in the induction period of secondary recrystallization. A rapid rise to an annealing temperature of 1260°C (2300°F) was obtained in a BaC12and NaCl fused salt bath. The structures that resulted from anneals in the range 12- to 1000-sec duration were relatively finegrained, even though the growth was a form of exaggerated grain growth13 or secondary recrystallization with a high nucleation frequency.= Many of the grains were large enough for an X-ray study using a 5-mil X-ray beam. A transmission Laue Camera and an optical-mechanical stage for moving the grains into the X-ray beam were used. A total of 325 grains were X-rayed in this manner and the grain orientations determined. Complete (110) pole figures were obtained for the primary recrystallization texture using CoKa radiation at 30 kv in the back-reflection range, such as (220) for (110) poles, as described recently by Newkirk and Bruce.10 The low voltage serves to reduce the spurious white radiation to a minimum. A filter of 0.001-inch iron foil was located in front of the detector slit for transmission and in front of the beam slit for back reflection. A new and improved specimen holder extended the useful tilting angle range for transmission to 70 deg instead of 60 deg as previously reported.&apos; A torque magnetometer was used to obtain the magnetic torque curves for a number of l-in. diam disk specimens. RESULTS The (110) pole figure of the material after recrystallization at 800°C is shown in Fig. 1. The positions of the pole concentrations are found to be

Jan 1, 1961

By M. T. Simnad, R. F. Mehl, L. Yang

Techniques for studying marker movement in K-Rb interdiffusion have been worked out. The results indicate that Rb diffuses faster than K and that the ring mechanism of diffusion cannot be the dominant one operating in this case or probably in cases involving other alkali metals, despite their low ion core repulsive energies. SEVERAL theoretical attempts have been made in the past decade to elucidate the mechanism of diffusion in body-centered-cubic metals. No general agreement, however, has been reached by different authors. Zener,1 and later LeClaire,2 on the basis of a correlation between the entropy of activation for self-diffusion and the temperature dependence of the elastic constants, predicted that a ring mechanism should operate in the diffusion of body-cen-tered-cubic metals. Paneth3 calculated the activation energies of various ring, vacancy, and interstitial mechanisms for the self-diffusion in alkali metals and concluded that the most likely one was based on the linear motion of "crowdions," which is in fact a different form of interstitial diffusion. Fumi,1 however, showed that the experimental values of the activation energies for self-diffusion in the alkali metals could be better accounted for if the diffusion process in these metals was assumed to follow a vacancy mechanism. The same conclusion was reached by Kojima5 for the self-diffusion in lithium. Experimental evidences published during the past few years seem to exclude the ring mechanism as the predominating one in the diffusion of body-centered-cubic metals. For instance, maker movement has been observed in ß-brass, first in this laboratory" and later by Resnick and Baluffi.5 Shewmon and Bechtoldh also found marker movement in the body-centered-cubic system Ti-Mo and showed that the argument which led Zener and LeClair to favor a ring mechanism was not incompatible with a vacancy mechanism. In spite of this, it seemed to the authors that further experimental tests should be made by studying the Kirkendall effect in body-centered-cubic systems that characteristically have small ion core repulsion, such as the alkali-metal systems. Since the ion core repulsion term constitutes the main part of the activation energy needed for the rotation of a ring, such a test should be the most critical of all. The system K-Rb was chosen for experimental study because these metals form a continuous series of solid solutions. Experimental Investigation Owing to the extremely active nature of these two metals, a brass dry box (18 x 11 x 10 in.) was built for making the diffusion couple. It had a big lucite window on top, two side ports through which neo-prene-rubber gloves were inserted, and another side port covered with an optically flat-glass window for microscopic examination of the sample. Inside the box there were a circulating fan driven with a rotating horse-shoe magnet located outside the box, a heater used to generate potassium vapor for getter-ing the box, and a cold trap for keeping the inside of the box cool. Chemically pure grade K and Rb were triple distilled before they were transferred in vacuum into cylindrical steel molds kept in pyrex-glass ampules, Fig. 1. The latter together with the tools needed for making the diffusion couple were put into the dry box. After the box was flushed with purified argon and gettered with potassium vapor, generated from a heated steel crucible inside the box, the glass ampules were broken and the mound on the top of the alkali-metal ingot was cut off with a razor blade to yield a flat surface. To make the diffusion couple, one K ingot and one Rb ingot were pushed out of the molds together with their steel supports by screwing a metal plunger into the bottom of each mold. They were then laid on a brass cradle inside the assembling carriage (shown separately in Fig. 2) with the flat faces opposite to each

Jan 1, 1959

By G. R. Green, R. C. McDonald

The International Nickel Co., Ontario Div. mines, faced with rising production requirements, short labor supply, and ever increasing labor costs turned to mechanized mining for a solution to its problems. The degree of mechanization of ore removal has increased from 1966 with the purchase of the first diesel-powered load-haul-dump (LHD) machine to the present, with over 53% of all underground production handled by these units. Keeping pace with mechanized ore removal, there has been a parallel development of drilling equipment to complement the mucking units. This paper deals with the applications and economic advantages of mechanized drilling at the underground mines of Inco, Ontario Div. It covers the use of various types of mechanized drills in such mining methods as cut-and-fill, induced block caving, and sublevel caving. The economics of raise boring are also discussed.

Jan 1, 1974

By Charles Jones

(San Francisco Meeting, September, 1915) IN any discussion of this very large subject we are confronted at the outset with so many obstacles that at best only a fragmentary and rather disconnected presentation can be made of it, and my hope is that building from the few facts I have to offer a more complete knowledge may be secured. In the whole intermountain and Pacific. Coast region, west of Pueblo, Col., and from Canada to Mexico, there is no production of pig iron, and steel production is confined to the manufacture of a small amount of open-hearth steel from scrap. When we consider the area, the resources, and the several centers of population, this condition seems anomalous, even in. the face of every counter argument as to cheap water transportation, or other means of transport from the Atlantic Seaboard or from the iron and steel centers of the Middle West. This comatose condition, if such a term may be applied, is certainly riot due to a lack of all the essential materials and factors for success in iron and steel smelting, but is rather, I think, due largely to the general fact that it is only within a comparatively few years that the centers of population on the Pacific Coast have attained a size that would entitle them to the position of distributing or freight centers, or that the "back country" has been enough built up to make it sufficiently interesting to the railroads to foster trade from the local centers to the interior points rather than seek to supply such local centers and the interior by a transcontinental haul.

Jan 9, 1915

By E. H. Crabtree, V. W. Winters, T. G. Chapman

IN 1939 one of the authors* described advances in carbon-cyanidation for the period 1932 to 1939 • T. G. Chapman: A Cyanide Process Based on the Simultaneous Dissolution and Adsorption of Gold. Trans. AIME (1939) 134, 207. and included: (1) the dissolution of gold in an ore pulp by cyanide and its simultaneous adsorption by carbon, (2) the stage addition of adsorptive carbon and its movement countercurrent to the flow of the ore pulp, and (3) the recycling of adsorptive carbon. Considerable additional experimental and pilot plant work have been done by the authors since 1939 and the results of such work E. H. CRABTREE, JR., Member AIME, is Director of Milling, Eagle-Picher Mining and Smelting Co., Miami, Okla., V. W. WINTERS is Superintendent, Sahuarita Concentrator, Eagle-Picher Mining and Smelting Co., Tucson, Ariz., and T. G. CHAPMAN, Member AIME, is Dean, College of Mines, University of Arizona, Tucson. AIME Sun Francisco Meeting, February 1949. TP 2744 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received March 3, 1949. have been sufficiently encouraging to justify a second paper. Developments from 1939 to 1948: In 1941, Verne W. Winters did the first experimental work in eliminating agitation during dissolution and adsorption and thereby demonstrated that the dissolution of gold by cyanide and its simultaneous adsorption by carbon take place essentially to completion in a stagnant pulp. Shortly thereafter, and as a result of the stagnant pulp experimental work, Winters and Chapman demonstrated that soluble gold, in a cyanide ore pulp, would migrate from the ore pulp through a perforated container and be adsorbed by carbon within the container. During the same year, the Eagle-Picher Mining and Smelting Co. erected a 25-ton capacity pilot plant at the Harquahala mine about 9 miles from Salome, Ariz. Experimental work at this plant comprised chiefly the stagnant pulp modification of carbon-cyanidation although considerable work was done in the grinding and activation of carbon, and testing various methods of extracting adsorbed gold from carbon. Soon after the completion of the Harquahala

Jan 1, 1951

By E. H. Crabtree, T. G. Chapman, V. W. Winters

IN 1939 one of the authors* described advances in carbon-cyanidation for the period 1932 to 1939 • T. G. Chapman: A Cyanide Process Based on the Simultaneous Dissolution and Adsorption of Gold. Trans. AIME (1939) 134, 207. and included: (1) the dissolution of gold in an ore pulp by cyanide and its simultaneous adsorption by carbon, (2) the stage addition of adsorptive carbon and its movement countercurrent to the flow of the ore pulp, and (3) the recycling of adsorptive carbon. Considerable additional experimental and pilot plant work have been done by the authors since 1939 and the results of such work E. H. CRABTREE, JR., Member AIME, is Director of Milling, Eagle-Picher Mining and Smelting Co., Miami, Okla., V. W. WINTERS is Superintendent, Sahuarita Concentrator, Eagle-Picher Mining and Smelting Co., Tucson, Ariz., and T. G. CHAPMAN, Member AIME, is Dean, College of Mines, University of Arizona, Tucson. AIME Sun Francisco Meeting, February 1949. TP 2744 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received March 3, 1949. have been sufficiently encouraging to justify a second paper. Developments from 1939 to 1948: In 1941, Verne W. Winters did the first experimental work in eliminating agitation during dissolution and adsorption and thereby demonstrated that the dissolution of gold by cyanide and its simultaneous adsorption by carbon take place essentially to completion in a stagnant pulp. Shortly thereafter, and as a result of the stagnant pulp experimental work, Winters and Chapman demonstrated that soluble gold, in a cyanide ore pulp, would migrate from the ore pulp through a perforated container and be adsorbed by carbon within the container. During the same year, the Eagle-Picher Mining and Smelting Co. erected a 25-ton capacity pilot plant at the Harquahala mine about 9 miles from Salome, Ariz. Experimental work at this plant comprised chiefly the stagnant pulp modification of carbon-cyanidation although considerable work was done in the grinding and activation of carbon, and testing various methods of extracting adsorbed gold from carbon. Soon after the completion of the Harquahala

Jan 1, 1951

By V. D. Perry

Mineralized breccia pipes, because of their wide-spread occurrence and close structural relations to some of the world&apos;s great ore bodies, are objects of unusual interest for mining engineers and geologists. The literature contains many references to them, but it is questionable whether their genetic significance and economic importance have been sufficiently emphasized. The purpose here is to stress these features, relating them to the field facts, for the particular benefit of younger generations of geologists who, confronted with and sometimes confused by the growing flood of geochemical, geophysical, and other specialized research approaches, may be reassured that mappable field relations remain a foremost guide to a better understanding of ore deposits. A mineralized breccia pipe is a pre-mineral, breccia structure which has controlled the circulation and deposition of subsequently introduced mineralization. It is composed of relatively rotated angular or rounded rock fragments, set in a mineralized matrix. A pipe in plan outline may be circular, oval or approach polygonal form, with a steep to vertical axis proportionately much greater than its horizontal dimensions. The pipe is a steeply plunging, chimney-like mass of brecciated rock cemented with later minerals.

Jan 4, 1961

By Hsun Hu

The microstructural changes during rolling and at various stages of recrystallization in (111)[112] oriented single crystals of Si-Fe have been studied by transmission electron microscopy. At very low deformation, the dislocation structure consists of jogged dislocation lines, edge dislocation dipoles, and numerous dislocation loops, which may be interpreted by the jog-formation mechanism in moving screw dislocations. Up to 70 pct rolling reduction, no sharply defined cells are formed. Subgrain forma- tion takes place somewhat earlier in the annealing process than in a similarly processed (110)[001] crystal. This may be partly responsible for the reported difference in the rate of recrystallization between (111)[112] and (110)[001] crystals. Evidence indicates that the formation of recrystallization nuclei occurs largely by the coalescence of sub -grains. This is consistent with previous observations on other Si-Fe crystals. AVAILABLE data in the literature indicate that the main features of rolling and annealing textures in (111)[112] and (110)[001] crystals are essentially similar. A (111)[112] or (111)[112] crystal can be rolled 70 pct without changing its initial orienta-

Jan 1, 1964

By Orville R. Lyons

This paper presents a method whereby the amount of misplaced material and the difficulty of the separation can be used to compare coal cleaning equipment of all types, from effectiveness and capacity standpoints. The correlations presented do not include all types of equipment currently available, but the method can be used to evaluate any make or type of coal cleaning equipment, both old and new. THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,&apos; but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."&apos; Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."&apos; It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913," by the United States Bureau of Mines in 1938,&apos; by Hancock in 1947," and by the national French research agency Cerchar in recent years.&apos; In 1950 Andersone proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or k0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1953

By F. D. Rosi, F. C. Perkins, L. L. Seigle

An investigation was made of the mechanism of plastic flow in coarse grained specimens of both sponge and iodide titanium at low (-196°C) and high (500° and 800°C) temperatures. Deformation by slip occurs predominantly on a {1011} plane and in a <1120> direction over this entire temperature range, and secondary slip on {101-1} planes becomes more prevalent with overthisentireincreasing temperature.range, The crystallographic habit of the predominant twin planes becomes more prevalent with type is temperature-dependent, and deformation by twinning increases as the temperature of testing is lowered. Kink bands were not observed at -196OC and rarely at the high temperatures. A LTHOUGH the deform a tional mechanisms in . -titanium at atmospheric temperature have been extensively investigated," there is little information regarding the influence of testing temperature on these mechanisms. The only available data come from the recent work by McHargue and Hammond, who extended single crystals of iodide titanium at a temperature of 815°C. No significant changes in the types of slip and twinning planes were observed, but increased activity on the type I, order 1 pyramidal slip planes and on the type 11, order 2 twinning planes was reported. These planes contribute very little to the deformation process at room temperature.&apos;&apos; &apos; Since there is interest in titanium as a material for use at both low and high temperatures, the present investigation was undertaken to examine the slip and twinning behavior in coarse grained specimens of titanium at -—196", 500°, and 800°C in order to determine the general effect of temperature on the mechanism of plastic deformation. Experimental Material Used and Specimen Preparation—Both sponge and iodide titanium were used in the present investigation; chemical analyses appear in Table I. These materials were arc-melted under argon into 25 g slugs, which were then cold-rolled approximately 90 pct to a sheet thickness of 0.05 in. Since the strain-anneal technique was used for obtaining coarse grains, the cold-rolled sheets were made into tensile specimens which were then annealed to produce a relatively coarse uniform grain structure prior to critical straining. The details of the strain-anneal treatment. size of grains, and the method for preparing the specimen surface for optical microscopy have been described in a previous report.&apos; In order to obtain a wider spread in crystal orientation for the present work, it was necessary to vary the rolling schedule to reduce the degree of preferred orientation in the annealed sheets prior to critical straining. Methods for Tensile Testing—The apparatus for experiments at the temperature of liquid nitrogen (—196°C) consisted of two concentric stainless steel

Jan 1, 1957

By D. Silverman, A. R. Brown

EquipmENT and methods for locating the points of entry of salt water into oil wells are described. These techniques make it possible to delineate accurately the top and bottom boundaries of water zones whether bottom water or intermediate zones of production, Data are given on tests by this survey method on a number of producing wells, Complete results were obtained on wells shelving water percentages ranging from high values to as Little as 10 pct salt water. A number of the wells tested were plugged back and the results are reported in detail. While not all the work-overs were successful, evidence, including the results of reruns by this survey method, points to failure of the plugback operations. The data provided in the tests discussed show, contrary to general opinion, that a large percentage approaching 50 pct of the wells showed intermediate water instead of bottom water. Furthermore, approximately a third of the wells tested showed multiple zones of water production. The equipment comprises a long pipelike assembly carrying 10 pairs of electrodes spaced apart a distance of 4 ft. A surface-controlled solenoid-operated switch is provided to connect each of the individual pairs of electrodes in turn to a single-conductor steel-armored cable by means of which the conductivity of the fluid in the vicinity of each of the electrode pairs can be continuously recorded at the surface. Any number of electrode pairs and any spacing can be used. This assembly is lowered on tubing and placed in position opposite the section of the well to be studied. A conventional rod pump is used to produce the well for the survey. The pump inlet is placed below the lowest electrode pair. The well is conditioned by pumping Out the salt water normally standing in the well and introducing fresh water into the annulus at the surface. When the resistivity of the water standing in the well has been increased to a sufficiently high value, the inflowing fresh water is stopped and the drawdown operation of the survey is started. As the fluid head is lowered by pumping, fluids flow into the well and the entry Of salt water is indicated by the change in resistivity of the fresh water opposite the &apos;Ones Of water entry, The process can be repeated as Often as necessary with little effort and without moving any well equipment to be sure that the fluids produced from each zone are representative Of the true reservoir content. Introduction The oil industry has been concerned from its inception with the control of fluids entering its wells. In order to effect the greatest economy of operation and to get the greatest total production of petroleum liquids out of the ground, the flow of gas and water must be controlled and often extensive workovers are planned and carried Out for this purpose. This has become even more important in recent Years because of the need for the conservation of natural resources. Whereas producing operations concerned with the original completion of a well are assisted to a great extent by a wide variety of instruments developed and perfected for that purpose, workover operations on oil wells have been greatly hindered by a lack of suitable instrumentation. The industry has searched for many years for a satisfactory instrument and process that

Jan 1, 1948

By P. Ramachandrarao, T. R. Anantharaman

EVER since the technique of quenching metals and alloys from the melt (splat cooling) was perfected a decade ago, it has been recognized that the grain size of products solidified by this technique may be extremely small.&apos; The further observation that fcc metals quenched from the liquid state contain very few dislocations has led to the inference2 that metals are subjected to negligible or no stresses during the rapid solidification characteristic of the "gun" or "piston-and-anvil" technique. Evidence for the incidence of appreciable densities of stacking faults has, however, been obtained in case of some splat-cooled fcc and hcp alloys,3 although not for pure metals. In the light of these earlier observations it was considered desirable to study X-ray line-broadening effects, if any, in fcc metals rapidly cooled from the melt. In the present work pure silver (>99.99 pct), aluminum (>99.99 pct) and lead (>99.9 pct) were quenched from the liquid state from temperatures about 50°C above the melting point by the "gun technique" and the resulting foils were subjected to X-ray examination in a Philips Diffractometer. The quenched foils (up to -10 u thick) did not generally stick to the substrate surface and could be easily transferred to the Diffractometer without introducing any plastic deformation. The profiles of the first five reflections from the foils were recorded in each case with Cu Ka, radiation at the slowest available scanning speed of 1/8 deg per min. To correct for instrumental broadening, profiles were also recorded from the metals annealed in vacuo at suitable temperatures. The integral breadths of the X-ray reflections were arrived at by a procedure described earlier.&apos; There was a distinct suggestion of preferred orientation in the recorded intensities of reflections from aluminum and lead foils. Such an effect was not observed in case of silver. In addition, the integral breadths of X-ray reflections from splat-cooled aluminum and lead were not significantly different from those recorded for the annealed metals. The analysis was therefore continued only for silver where the X-ray line broadening was appreciable. The pure diffraction broadening, B, was evaluated for each X-ray reflection (hkl) from silver from the observed, B, and instrumental, b, breadths with the aid of each of the three equations due to Scherrer,5 Anantharaman and Christian,6 and Warren and Biscoe,7 respectively: Bs= B-b BAC=B- b2/B Table I gives the values of particle size, 71, the lattice strain, E, arrived at by the use of the following well-known relations and on the assumption that all observed diffraction broadening could be attributed to lattice strain or particle size, respectively: E = 1/4 cos ? n= B cos ? where A is the wavelength of X-radiation and 0 is the Bragg angle. As no significant peak shifts or asymmetry could be detected in the profiles from the foils, the possibility of any significant contribution due to twins or stacking faults was ruled out. The absence of faults is by no means surprising since pure silver is known to develop stacking faults only on severe deformation and the stacking fault densities recorded so far for even silver filings have been extremely low.&apos; The very low values for percentage mean deviation from the mean value for the particle size in Table I strongly suggest that all observed broadening in splat-cooled silver can be attributed only to small particle size. This conclusion receives further support from the lowest mean deviation recorded for data computed from the Scherrer equation based on Cauchy profiles that are considered characteristic of particle size broadening. Further analysis for separation of particle size and lattice strain effects was considered unnecessary in view of the very large mean deviations obtained for strain values and also the earlier results suggesting absence of even detectable strain in metals and alloys quenched from the melt. It is to be stressed in this connection that the particles are actually grains and not cells formed by walls of high dislocation density usually encountered in deformed samples. As such, the absence of strains is not surprising. The present results are probably the first to record X-ray line broadening due only to small particle

Jan 1, 1970

By C. L. Meyers, A. V. Levy, G. Y. Onoda, R. J. Kotfila

This paper presents the hypothesis that solid-solution hardening of regions in the order of tens of angstroms thick along grain boundaries is the most important mechanism controlling the ductile -brittle transition behavior of poly crystalline bcc refractory metals. Further, a physical model is developed and a general equation is derived to describe the dependence of the solute concentration at grain boundaries on temperature, nominal impurity concentration, thermal treatments, vain size, and prior plastic deformation. Analytical curves of the solute concentration at grain boundaries us temperature, calculated by means of the derived equation, are found to have the same general form as curves of ductility us temperature plotted from experimental data. Senziquantitative relationships between the transition temperature and metallurgical variables can he determined by using the physical model. The room-temperature brittleness of the poly-crystalline refractory metals (tungsten, molybdenum, and chromium) is a result of their high ductile-brittle transition temperatures. Recently studies on single crystals have revealed that, when sufficiently pure, these crystals have much lower transition temperatures than polycrystalline specimens of similar purity.&apos;-3 For example, the transition temperature (measured by reduction in area in tensile tests) for very high-purity tungsten crystals has been reported to be as low as -50°F whereas polycrystalline specimens of similar purity had a transition temperature near 400" ~.&apos; These results suggest that the ductile-brittle transition behavior of these polycrystalline metals can be attributed principally to the influence of grain boundaries on plastic flow and fracture. This paper contains a discussion of the manner in which grain boundaries influence the ductility of the poly-.crystalline bcc refractory metals and proposes that the segregation of impurities to grain boundaries is the most important mechanism for controlling the ductile-brittle transition behavior of these metals. Further, this paper contains an analysis of the effect of the compositional and structural variables on the grain boundary-ductility relationship, and introduces a semiquantitative model that can provide a foundation for more theoretical treatment to describe the influence of these variables on ductile-brittle transition behavior. PHYSICAL MODEL FOR PREDICTING DUCTILE-BRITTLE TRANSITION BEHAVIOR Grain Boundary Segregation of Impurities. Based on their own observations and on theoretical grounds, numerous investigators have suggested that impurities segregate to the grain boundaries. Such segregation would be expected because regions exist where both large and small foreign atoms fit with less strain than within the undistorted crystal structure. Therefore, the concentration of impurities should be higher at boundaries than within the grain body. TO estimate the degree (i.e., the ratio of grain boundary to nominal bulk concentration) to which an interstitial solute tends to segregate at boundaries within a solvent metal, the solubility rather than the size misfit could be used as a guide because solubility expresses the joint effect of both elastic and electronic factors.5 The solubilities of interstitial elements such as carbon, hydrogen, nitrogen, and oxygen are low in the group V-A metals and very low in the group VI-A metals.6 These low solubilities suggest that segregation to grain boundaries should occur for each of these solutes in both refractory metal groups. The difference between the ductility of single-crystal and polycrystalline bcc refractory metals can be described in terms of two distinct effects.4 The first of these is the general observation that grain boundaries hinder slip within grains and slip transfer between grains, and the second is that deformation is more complex in each grain of a polycrystalline specimen than it is in a single crystal. Mc Lean has pointed out, furthermore, that strong slip-hindrance effects at grain boundaries should occur in metals having strong segregation of impurities to grain boundaries. Therefore, the effect of grain boundaries on the hindrance of slip is expected to be the dominating influence on the ductile-brittle transition behavior of these polycrystalline refractory metals. cahn5 has suggested that temperature and solute mobility should influence solute equilibrium segregation at grain boundaries, and Fig. 1 illustrates

Jan 1, 1965