Search Documents

By F. W. Jessen, N. Mungan

The plastic flow characteristics of clay water suspensions were first recognized by Binghaml in 1916 and further studied by Ambrose and Loomis' in 1931-1932. Many physical and chemical properties of clay suspensions are deeply influenced by particle size distribution as well as by the exchange cation. Separation of a number of fractions is particularly helpful in making a detailed study of a suspension. A limited amount of work has been conducted on the effects of particle size on specific properties of mud drilling fluids. A knowledge of particle size distribution is essential for a better understanding of fundamental properties of clay suspensions, particularly viscosity and gel strength. The purpose of this investigation was to study the effect of particle size on the viscosity and gel properties of clay suspensions and to determine any changes in mineral composition accompanying variation in size. EXPERIMENTAL PROCEDURE Numerous methods may be used to fractionate a poly-dispersed clay suspension into nearly mono-dispersed systems. Particles larger than 44 micron (325-mesh) may be obtained by wet screening. For sizes from 44 to 1 micron, the fractionation may be accomplished by sedimentation, elutriation plus microscopy,' or turbidimetry.6 When dealing with systems which contain a major portion of particles below l-mi-cron size, slit ultramicroscopy,7 centrifuge methods of Svedberg,5 eams,9 and McBain,l0 and X-ray methods" may be employed. The Sharples super centrifuge has been proved suitable for the economical separation of suspended particles of submicron range.12,13,14 Three-hundred and forty-five gal of 1 per cent by weight Aquagel suspension was mixed in a high-speed 5-gallon mud mixer and the suspension was allowed to stand in 5-gal glass bottles for 30 days to assure full hydration. All particles larger than 44 microns were removed by wet screening. Five fractions in the range of 44 to 1 micron were obtained by sedimentation. The Sharples super centrifuge method described by Hauser and Reed.13 Norton and Speil,14 Ha user and Lynn,15 and Hauser and Schachman,10 as employed to yield five fractions of submicron size. A super centrifuge operation chart prepared by Fancher, Oliphant, and Houssierre12 was used to determine operating conditions for the desired particle ranges. The clay suspension, after removal of all material above 1-micron size, was centrifuged. During rotation of the bowl, the particles were deposited on a thin plastic liner which fit closely inside the bowl. After passing 5 gal of suspension through the centrifuge, the liner was removed and the particles on the liner were scraped off, remixed and recentrifuged. This was repeated five times. Thus, Fractions H, I, K, and L were obtained. The finest fraction, M, remained in an approximately 0.4 per cent suspension. Water was evaporated under reduced pressure from this suspension to yield the finest particles. Results of the fractionation are included in Table 1. In order to achieve proper orientation and humidity conditions for X-ray diffraction analysis, the following procedure was employed. The dilute suspensions were placed on glass slides and allowed to dry at room temperature. This was repeated several times. Previous to measurement each sample first was placed in a water desiccator for half an hour and then allowed to stand for 15 minutes at room temperature. thus yielding an equilibrium condition of about 52 per cent relative humidity. The relative humidity of the room in which the X-ray diffraction was carried out was maintained at approximately 50 per cent so that there was no change in the spacings during the X-ray examination. Samples

By W. C. Hauber

Techniques previously published to predict the production performance of a water flood when the mobility ratio is not unity have been primarily restricted to a five-spot well pattern. When other types of well patterns are considered, the prediction of performance has required either a model study or a complex numerical solution of a multiple-fluid system with a high-speed digital computer. Simple methods are developed in this report for predicting the areal sweep efficiency and injectivity history of a water flood for arbitrary well patterns and mobility ratios. The effect of an initial gas saturation can be incorporated into this method of prediction. With the layer superposition concepts published by Prats, et al.,1 these methods can be used to predict the production performance of a water flood in a reservoir having a wide range in permeability. A reasonably good agreement is shown by comparisons of the results calculated by this method with those obtained either by model studies or by complex numerical solution of multiple-fluid systems. Therefore, it has been concluded that a reasonably accurate method has been developed for predicting the production performance of a water flood employing an arbitrary type of well pattern for any given mobility ratio. A medium-speed digital computer can be used in applying this method. INTRODUCTION Production performance of multi-fluid five-spot water floods can be predicted by the techniques published by Prats, et al.1 This technique takes into account the effects of initial gas saturation, mobility ratio and vertical variations in horizontal permeability. A basic assumption in applying this technique is that unit displacement efficiency does not vary with time after the passage of the flood front. Prats, et al. demonstrated that this assumption is valid for normal waterflood applications with small mobility ratios. To extend Prats' technique to other types of well patterns has required either an experimental model study or a numerical solution of a multiple-fluid system to describe the performance of an individual homogeneous layer. Sheldon and Dougherty2 presented an exact numerical solution employing any arbitrary well pattern. This technique is complex to apply, requiring (1) numerical solution of the single-fluid system, (2) conformal mapping of the streamlines and iso-potential lines to form a new grid network, and (3) a numerical solution of the multi-fluid system on the new grid network. A method was developed in this paper to approximate areal sweep efficiency and injectivity as functions of time for an individual homogeneous layer for arbitrary well patterns and mobility ratios. Analytic expressions were derived to directly apply this method to five-spot and direct line drive well patterns. For other types of well patterns, this method is similar to the approach of Higgids and Leighton,6 in that it utilizes the stream tubes and iso-potential lines obtained by the solution of differential equations when the mobility ratio is unity. However, this method is easier to apply than the Higgins-Leighton method since it does not require knowledge of the variation between oil and water relative permeabilities and saturation. Using the relationship between areal sweep efficiency, injectivity and the volume of water injected into an individual homogeneous layer as obtained by the method presented in this paper, and Prats' technique for the superposition of individual layers, one can predict the production performance of any water flood. ASSUMPTIONS GENERAL Basic assumptions made in this report are that fluids are incompressible and the layers are horizontal, homogeneous and uniformly thick. It is assumed that as water is injected into the layer, three distinct regions are formed —a water bank, an oil bank, and an unflooded region. Each region is assumed to displace other regions in a pis-tonlike manner, with only one fluid flowing in each region, so that there is no change in unit displacement efficiency with time after the flood front has passed in the reservoir. Therefore, the residual oil saturation in the water bank and the oil saturations in the unflooded region are constant throughout the layer. The ratio (F) of the bulk volume of a layer occupied by the oil and water banks at any time before oil breakthrough, to the corresponding bulk volume of a layer occupied by the water bank, is given' by the equation BREAKTHROUGH AREAL SWEEP EFFICIENCY To predict the behavior of any type of waterflood pattern, one must know the breakthrough areal sweep efficiency Eb(Mc,o, F) for the pattern for any water:oil mo-

Jan 1, 1965

By D. E. Peacock, B. Harris

The mechanical behavior of a niobium (columbium)TUNG alloy containing 20 wt pet Ta. 15 wt pet W, and 5 wt pct Mo has been studied in the temperature range 77° to 423°K. All specitrzens tested, apart from those into which oxygen was introduced deliberately, were fully recrystallized at 1500°C, had an average grain diameter of approximately 0.03 mm, and a combined carbon, ox-vgen. nitrogen, and hydrogen content of not not more than 250 ppm The meckatnical behavior of this alloy was found to be similar in seine respects to that of unalloyed bcc transilion metals. Both yield and flow stresses were sensililae to changes in deformation rate and both increased rapidly as the temperature was lowered below 150°C. A detailed examination revealed, however, that most of the temperature dependencc of the yield stress could be accounted for by the temperature dependence of the elaslic, modulus, whish is not true of the unualloyed metals. In lension at moderate strain rates, the trunsition fvom ducfile to hvittle behavior occurred just belour room teunperature bur incveasing the oxygen content from 190 to 200 pptn raised the transition temperature to about 4000K. TUNGSTEN and molybdenum have been found to be very effective high-temperature solid-solution strengtheners of niobium, but the amounts of these elements that can be added are limited if the alloy is to retain useful room-temperature ductility. It has been shown, however, that partial replacement of niobium with tantalum lowers the ductile-to-brittle transition temperature of such alloys and allows larger additions of molybdenum and tungsten to be made. Some of the high-temperature properties of niobium alloys containing these elements have been reported by Bartlett et al.,' and the work presented here describes the low-temperature behavior of one of these, a solid-solution alloy containing, by weight, 20 pct Ta, 15 pct W, and 5 pct Mo. The elastic modulus, the temperature and strain-rate dependence of the yield and ultimate tensile stresses, and strain-hardening effects are discussed and compared with those of unalloyed niobium. EXPERIMENTAL MATERIAL AND PROCEDURE The material used in this investigation was produced from a 6-in.-diameter, double arc-melted ingot. This was can-extruded at about 1150°C to a 3-in.-diameter billet, and after annealing for 1 hr at 1345°C the billet was heated to 1315OC and part rolled and part forged to 0.5-in.-thick plate. The resulting material exhibited a cold-worked structure

Jan 1, 1965

By O. D. Sherby

In 1938, Kanter' revealed that the steady-state creep rate of low-carbon iron alloys could be correlated by an activation energy expression, where the activation energy for creep, Qc, was found equal to about 90.0 kcal per mole for most of the alloys investigated. He suggested that creep at high temperatures might be controlled by some sort of solid self-diffusion process since the value of Qc was about equal to the known value for self-diffusion, Qd. Correlations were not further attempted along these lines until many years later, when new evidence2-8 was presented suggesting that Qc = Qd for many metals. This equality now appears to be established for ten metals (Al, Pb, Ni, Mg, Cd, In, a Fe, y Fe, Cu, and Au). This experimental fact prompted several investigators to postulate various mechanisms of dislocation motion which would yield an activation energy for creep equal to that for self-diffusion.7-9 Possibly the most accepted theory is that based on dislocation climb7 where a dislocation is envisioned to surmount a barrier by an atom-vacancy exchange process, thereby "climbing" from one slip plane to another. Such a model would suggest that the steady-state creep rate, i, should be directly proportional to the rate of self-diffusion, D, for a given creep stress. In order to more clearly reveal the relationship between creep and diffusion, and to eventually determine the correct model, it would be desirable to obtain data showing correlations between i and D, rather than with a comparison of the temperature coefficients, Q. It has been known for some time that the self-diffusivity of iron atoms is greatly decreased when body-centered-cubic (a) iron transforms to face-centered-cubic (y) iron. This has been ascribed to the more close-packed structure of y iron. The diffusivity ratio at the transition temperature is Da/Dy =350. Correlations of creep data for a and y iron5 reveal that the creep rates under a given stress at the transition temperature differ by about the same ratio (ea/ey 2 200). It would be difficult to reconcile these results on any other basis than that the diffusivity of atoms probably controls creep of iron in some very direct way. No other published data on other allotropic metals appear currently available for further checking such a possible correlation between i and D. Thallium transforms from a hexagonal close-packed (a) structure to a body-centered-cubic (ß) structure at 230°C (503°K) and the self-diffusivities of the two structures have been determined by shirn.10 His results are plotted in Fig. 1 where it will be noted that Dß/Da = 25 at the transition temperature. It would appear desirable, therefore, to determine the creep rates of polycrystalline a and ß thallium at the transition temperature, as well as determine

Jan 1, 1959

By L. Kaufman

An equation is derived relating AF a", the difference in free energy between austenite and martensite, to temperature and composition in the iron-chrmnium and iron-chromium -nickel systems. This equation is used to calculate at M,for low-carbon stainless steels. A method for utilizing the energetic equations to calculate M, in stainless steels is suggested. In addition, an explanation is given for the anomalous effect of chromium in forming a y loop concurrent with the lowering of M, in iron-base alloys. It has been demonstrated that the effect of alloying elements on the Ms temperature is strongly dependent upon the influence of the alloying element on the thermodynamic properties of the y and a phases. Notwithstanding the fact that alloying elements affect the Ms temperature by changing the lattice parameters, elastic constants, and inter-facial energies of the a and y phases, their primary role is a thermodynamic one. Thermodynamic analyses have been presented for the iron-carbon'-4 and iron-nickele systems in which equations are derived for Fa and FY, the free energies of the b.c.c. (or b.c.t.) and f.c.c. phases. These equations, which can be obtained with the aid of the equilibrium diagrams, can be used to help predict the Ms vs composition curves. This paper deals with a calculation of the thermodynamic properties necessary to compute AFffLY for iron-chromium alloys. In view of the lack of direct information concerning the activity of chromium in the a and y phases of iron, the regular solution approximationa,g was utilized to bridge the gap. After the necessary equations were derived for the iron-chromium system they were used to calculate AFff— Y for stainless steels by combining them with the previous results obtained for iron-nickel alloys. The results of these calculations offer a means of rationalizing the anomalous behavior of chromium in iron-base alloys. The latter depends on the regular solution approximation in contrast to the explanation offered by zener , which is based upon the "magnetic specific heat effect." THERMODYNAMICS OF THE IRON-CHROMIUM SYSTEM If y represents the atomic fraction of chromium in an iron-chromium alloy, then the free energy of the b.c.c. phase Fa, the f.c.c. phase FY, and the difference in free energy between the f.c.c. and b.c.c. phases of the same composition are given through [3] and Fmy represent the free energies of mixing of the a and y phases; while @era -' and uFea 4Y represent the difference in free energy between f.c.c. and b.c.c. chromium and iron respectively. The values of AEFe0ff4Y in the temperature range between 0" and 900K ( .

Jan 1, 1960

By Victor deWolfe

INTRODUCTION The Henderson Mine, located near Empire, Colorado, utilizes a continuous panel caving system to extract ore as one of the world's major producers of molybdenum. Any mine using a caving-by-gravity technique of mining must rely on closely controlled draw of the caved ore. This control is essential to insure proper caving action, to avoid damaging load concentrations of weight and to minimize the dilution of ore with waste material. Henderson is no exception. Draw control is a major factor in all production planning, from long- range plans to short-range and day-to-day ore scheduling. Draw control is reviewed constantly and administered daily in an effort to optimize production efficiency, ore recovery, and cave management. MINING METHOD The cave at Henderson is massive, moving slowly through large panels that are 244 m (800 ft.) wide by 610 m (2,000 ft.) long. Generally two cave areas are drawn at one time. The areas under active draw vary in size but can be as large as 244 m (800 ft.) by 244 m (800 ft. ) containing 400 draw points. Each draw point contains 45,360 mt (50,000 st) on the average and takes about two and one half years to exhaust. A complete panel is worked for seven to ten years. No pillar exists between panels, but rather a buffer zone of broken ore, or "static face," is left in each panel to be drawn with the adjacent, yet-to-be-caved panel in efforts of minimizing dilution of a working area from an exhausted one. (Figure 1) Production drifts are driven on 24.4 m (80 ft.) centers through the ore body. Between the production drifts are funnel-shaped draw bells on 12.2 m (40 ft.) x 24.4 m (80 ft.) centers to receive ore from the cave. Each bell is accessed by two draw points, one from the production drift on either side, thus forming a 12.2 m (40 ft.) x 12.2 m (40 ft.) draw pattern. Extraction of the ore is by rubber-tired, 3.8 m3 (5 yd3) load-haul-dump equipment. The LHDs then tram the ore a maximum of 49 m (160 ft.) to ore passes. Cave initiation and bell development are done from the undercut drifts which are parallel to and 17 m (55 ft.) directly above the production drifts. Longhole rings are drilled and blasted from the undercut drifts to define the bells and establish the undercut for caving. (Figure 2) DRAW CONTROL Since the cave line at Henderson is constantly advancing, it is necessary to be continually initiating new cave at one end while exhausting it at the opposite end. There must exist, therefore, an angle on the ore-waste contact in the broken rock from initiation to exhaustion. The basic concept of draw control is to keep this angle as smooth and even as possible, particularly at the time of exhaustion. If this is achieved, draw points are exhausted more or less in a line, avoiding pockets of remaining ore surrounded by exhausted areas. These pockets would cause spotty ore extraction at the time of exhaustion, increasing the amount of dilution occurring while introducing the potential for significant weight problems in the production area. To arrive at the desired angle on the ore- waste contact, maximum tonnage percentages are assigned to each row of draw points increasing at 10% or 15% increments (depending on cave size and velocity of draw) working away from the cave line. The available tonnage indicated by these percentages is the maximum allowable tonnage to be extracted from each draw point until the available tonnage percent- age is increased. As the cave moves, these percentages increase for each draw point regularly. However, in general the tonnage drawn from each draw point is kept at about 50% of this allowable maximum in order to maintain adequate available tonnage in the cave to sustain production for seven months if cave initiation were to cease. This available tonnage cushion is a safeguard built into the draw control program at Henderson to accommodate fluctuations in the rate of cave advance. When draw points move past the row of 100% tonnage availability, they are drawn past the desired 50% at the same increments per row until exhausted. (Figure 3) To achieve proper draw control, the number of LHD buckets to be taken from each draw point is assigned daily. The actual buckets taken, which may at times deviate from the

Jan 1, 1981

By T. V. Philip, R. E. Lenhart

When commercial silicon iron sheets of varying magnetic quality are isothermally annealed at high temperatures, extremely large grains develop in the material having good magnetic properties. These grains are of the (110) [001] orientation and are formed by secondary recrystallization. The primary driving force for this secondary recrystallization is grain boundary free energy. For the secondary grains, activation energies of 103 kcal per mole for nucleation, and of 75.5 kcal per mole for growth, were obtained. The activation energy for nucleation of the secondary grains is consistent with a model involving redistribution of a precipitate acting as the primary grain growth inhibitor. SINGLY oriented silicon iron sheet was first produced in 1935.1 The material as commercially produced today has a very highly developed preferred orientation or texture; up to 95 pct of the grains are crystallographically oriented with their (110) planes in the plane of the sheet and their [loo] directions parallel to the rolling direction. This texture, usually written as (110) [00l], is referred to as the "GOSS" or the "cube-on-edge" texture. Because the magnetic properties of this material are superior to those of the nonoriented sheets in the direction of rolling, the oriented silicon iron has acquired tremendous industrial importance especially in the manufacture of transformer cores and other electrical equipment. The commercially produced material is essentially an iron-silicon alloy containing about 3 1/4 pct Si with minor impurities totaling less than 0.15 pct. The silicon steel heat is melted in the open hearth or electric furnace. The ingots are hot rolled, with or without being slabbed, to strips of 0.100 to 0.080 in. thickness. They are then cold reduced to an intermediate thickness, recrystallized, cold reduced to final thickness, decarburized, and finally annealed at a high temperature. During this high-temperature anneal, extremely large grains with the cube-on-edge texture are produced in the sheet. Several papers have appeared in the literature2-10 relating to the production of the Goss-textured material. Most of these describe the textures produced on cold rolling and on subsequent annealing of single crystal or polycrystalline silicon iron. May and Turnbull11,12 have recently shown the necessity of a second-phase dispersed impurity in the material for the production of the Goss texture. However, none of these papers describes in detail the nucleation and growth kinetics of the (110) [001] grains during the final high-temperature anneal.* The present work, therefore, is an attempt to understand the nucleation and growth kinetics of the cube-on-edge grains in the silicon iron sheet during the final high-temperature anneal.

Jan 1, 1962

ARTICLE I Name and Object Sec. 1. This Division shall be known as the Institute of Metals Division of the American Institute of Mining and Metallurgical Engineers. Sec. 2. The object of the Division shall be to furnish a medium of cooperation between those interested in the field of physical metallurgy; that is, the nature, structure, alloying, fabrication, heat treatment, properties and uses of metals; to represent the AIME insofar as physical metallurgy is concerned, within the rights given in AIME Bylaw, Article XI, Sec. 2, and not inconsistent with the Constitution and Bylaws of the AIME; to hold meetings for the discussion of physical metallurgy; to stimulate the writing, publication, presentation and discussion of papers of high quality on physical metallurgy; to accept or reject papers for presentation before meetings of the Division. ARTICLE II Members Sec. 1. Any member of the AIME of any class and in good standing may become a member of this Division upon registering in writing a desire to do so, but without additional dues. Sec. 2. Any member not in good standing in the AIME shall forfeit his privileges in the Division. ARTICLE III Funds Sec. 1. The expenditure of the funds received by the Division shall be authorized by the Executive Committee of the Division. ARTICLE IV Meetings Sec. 1. The Division shall meet at the same time and place as the annual meeting of the AIME, and at such other times and places as may be determined by the Executive Committee subject to the approval of the Board of Directors of the AIME. Sec. 2. The annual business meeting shall be held within a few days before or after the annual business meeting of the AIME. Sec. 3. At a meeting of the Division, for which notice has been sent to the members of the Division through the regular mail or by publication in the Journal of Metals at least one month in advance, a business meeting may be convened by order of the Executive Committee and any routine business transacted not inconsistent with these Bylaws or with the Constitution or Bylaws of the AIME. Sec. 4. For the transaction of business, the presence of a quorum of not less than 25 members of the Division shall be necessary. ARTICLE V Officers and Government Sec. 1. The officers of the Division shall consist of a Chairman, a Senior Vice-Chairman, a Vice-Chair -man, a Secretary and a Treasurer. The office of Secretary and Treasurer may be combined in one person, if desired by the Executive Committee. Sec. 2. The government of the affairs of the Division shall rest in an Executive Committee, insofar as is consistent with the Bylaws of the Division and the Constitution and Bylaws of the AIME. Sec. 3. The Executive Committee shall consist of the Chairman, Senior Vice-Chairman, Vice-Chairman, past Chairman, Secretary, and nine members, all of whom shall be nominated and elected as provided hereafter in Article VII. Sec. 4. The Chairman, Senior Vice-Chairman and Vice-Chairman shall serve for one year each, or until their successors are elected. Each member of the Executive Committee shall serve three years. The Chairman shall remain a voting member of the Executive Committee for one year after his term as Chairman. Sec. 5. The Treasurer of the Division shall be invited to meet with the Executive Committee, but without ex-officio right to vote. He shall be appointed annually by the Executive Committee, from the membership of the Executive Committee or otherwise. Sec. 6. The annual term of office for officers of the Division shall start at the close of the Annual Meeting of the Institute and shall terminate at the close of the next Annual Meeting. ARTICLE VI Committees Sec. 1. There shall be standing committees as follows: Programs Committee. Finance Committee, Membership Committee, Annual Lecture Committee, Technical Publications Committee, Mathewson Gold Medal Committee, Nominating Committee, Education Committee and such other Committees as the Executive Committee may authorize. Sec. 2. It shall be the duty of the Programs Committee to secure the presentation of papers of appropriate character at meetings of the Division. Sec. 3. It shall be the duty of the Finance Committee to inquire into and examine the financial condition of the Division and to consider proper means of increasing its revenue and limiting its expenses. The Finance Committee shall audit the accounts of the Division and report to the Executive Committee prior to the Annual Meeting of the Division. It shall render a budget to the Executive Committee estimating receipts and expenses for the ensuing year so that action can be taken on same at the first meeting following the Annual Meeting.

Jan 1, 1953

By D. H. Forbes, I. B. Cadoff, H. M. Manasevit

Single-crystal silicon films have been obtained on several natural crystal faces of BeO using the thermal decomposition of silane and the hydrogen reduction of silicon tetrachloride. From an analysis of X-ray diffraction data it was determined that the following film-substrate orientation relationships exist: (111) Si 11(0001) BeO, (111) Si 11(1011) BeO, (100) Si 11f1010) BeO. and (110) Si 11(1010) BeO. An analysis of the crystallographic relationships between the film and substrate indicates that a match occurs between the silicon atoms in the film and the berylliuni ion sites in the substrate. This correspondence is in agreement with previous work on the deposition of silicon on sapphire.1-3 silicon on spinel: and tungsten on sapphire. The high resistivity, thermal conductivity, and radiation resistance of beryllium oxide make it an important substrate material for the deposition of thin films of silicon or other semiconductors. The importance of semiconductor-insulator composites to the field of integrated microelectronics has been well-documented in the case of silicon on sapphire.'-' The successful growth of large-area single-crystal silicon on an insulator, sapphire, was first reported in 1963.1,2 Since that time studies have been made of the crystallographic relationships between the deposited film and the sapphire substrate. On the basis of the observed relationships, a model has been proposed relative to the crystallographic requirements for epitaxy between the semiconductor film and the metal oxide substrate.3 It is proposed in this model that epitaxy is the result of a match between atoms of the deposited film and the metal ion sites of the substrate plane. This match is not limited to a 1 to 1 correspondence between sites in the two lattices. Sub- sequent studies of the deposition of silicon on spinel4 and tungsten on sapphire5 have yielded data which support this model. On the basis of this previous work it was felt that silicon on BeO should also fit this model. In the present study, the choice of substrate orientation was limited to the natural faces of synthetic BeO crystals. Of the faces available, the (0001) plane seemed the most favorable for epitaxial growth. EXPERIMENTAL PROCEDURE Silicon films were deposited from silane and silicon tetrachloride in the apparatus shown in Fig. 1. The hydrogen ambient gas was purified by passage either through a DEOXO unit, molecular sieves, and a liquid nitrogen cold trap, or through a heated Pd-Ag thimble. The gas was then mixed with the silicon source materiai and passed over the substrate which lies on a spacer above an inductively heated silicon pedestal. The following deposition conditions were used: a hydrogen flow rate of 3 liters per min with silane and silicon tetrachloride concentrations of 0.2 mole pct and a pedestal temperature of 1175" * 5°C as observed with an optical pyrometer assuming an emissivity of 1.0. Deposition was preceded by a 15- to 30-min hydrogen-etch period conducted at a temperature of 1275°C (obs). Adherent silicon films from 2 to 10 u were grown on the various BeO faces. The substrates were synthetically grown beryllium oxide single crystals ranging from 5 to 10 mm in

Jan 1, 1967

By F. W. Jessen, John C. Miller

In many areas where carbonate rocks form important parts of the stratigraphic sequence, stratigraphers have experienced varying degrees of difficulty in differentiating and correlating limestone and dolomite units in both surface and subsurface work. With early Paleozoic rocks of the Mid-Continent, insoluble residues yield a remarkable amount of strati-graphic data and relatively good correlations may be carried over broad distances.' Unfortunately, neither such information nor electric logs and radioactive logs have been particularly helpful in interpreting the limestone sections of the Permian Basin of West Texas. This is because: (1) the variations in the sections may be very slight; (2) no completely satisfactory method of interpretation has been developed; and (3) the measurements themselves are not sensitive enough for small variations. Also, such logs are influenced by the fluid content. Paleontology and micro-paleontology remain the ultimate arbiters. As a routine tool, however, paleontol-ogical examination is slow and tedious. Chemical analysis may be used, but this, too, is extremely slow. Although rocks are not classified according to chemical composition, there is considerable variation with rock types. Correlation by chemical composition has two advantages, first, the characteristics determined are subject to minimum human error and interpretation, and secondly, the lithologic changes are not masked by fluid content as in the case of electric and radioactive logs. Some fossils concentrate certain elements which tentatively might be used to date rock units.' Rapid chemical analysis by spec-trographic means could be used as an adjunct to other means employed in correlation work, or might, in itself, present a suitable method. PURPOSE OF THIS INVESTIGATION Sloss and Cooke' have published data concerning spectrographic analysis of limestone rocks specifically for purposes of direct correlation of a single formation. These authors found satisfactory evidence that differences in percentage of four elements (Mg, Fe, Al, and Sr) in the Mississippian limestones of northern Montana were useful in carrying out correlation of this formation over a distance of approximately 50 miles. It was concluded from the preliminary work that the spectrochemical method offered possibilities of solution of some problems of correlation heretofore not possible. Since the work of Sloss and Cooke' was confined to one particular limestone zone, extension of the use of the method to examine two or more geologic formations would aid materially in the over-all problem of correlation of such rocks. Equipment is now available commercially with which very rapid spectrographic analyses may be made, and hence the problem was to determine whether the variations existing in the minor constituents of limestones were sufficient for use in possible correlation. Qualitative and semi-quantitative investigations were made to determine whether significant changes in the chemical condition occurred. It was a further purpose to investigate the geologic time-boundaries to see whether significant chemical variation could be found corresponding to the paleontological breaks. It was desirable to attempt correlation of a thick section of limestone or dolomite rock and to have as much information as possible on the section. Furthermore, it was felt that examination of formations more difficult to correlate by other means would enhance the value of the method should definite points of correlation be found. Samples were chosen from the Chapman-McFarlin Cogdell No. 25 well in the Cogdell field, Kent County, Tex., and from the General Crude Oil Co., Coleman No. 193-2 well in the Salt Creek field, Kent County, Tex. These fields belong to the famous series of "Canyon" reef fields of West Texas. Cores from the above wells were available from the United States Geological Survey, Austin, Tex. THE SPECTROGRAPHIC METHOD The choice of procedure to be followed in this investigation was based on the anticipated requirements peculiar to the problem. Since the problem was primarily to investigate the possibilities of applying the spec-trograph to problems of correlation in thick carbonate sections, a precise quantitative analysis did not appear necessary. A qualitative analysis to show the possible absence of presence of any element, or a semi-quantitative analysis of the elements present to show the relative changes in magnitude of selected elements was required. Both types of analysis were employed. The two most widely applied methods of semi-quantitative estimates are those of Harvey and of Slavin4,5 though various other procedures have been described.6 while the Harvey method has been modified by Addink,7 this refinement did not seem necessary to the present problem. Essentially, the procedure employed is a variation of the total energy method of Slavin with two exceptions: (1) stressing matrix effect, and (2) using densitometer measurements. As measured by a densito-

Jan 1, 1956

By T. F. Mueller, P. A. Witherspoon

For the case of an infinite radial system operating at constant terminal rate, the reservoir engineer often uses the "point source" solution of the diffiusivity equation to study pressure interference effects. At early times and at short distances from the inner boundary these solutions are invalid. The amount of error is often not precisely defined because of mathematical difficulties. Work presented here shows that, if dimensionless time is defined appropriately, previous solutions of the pressure equation can be displayed .as a family of curves on one chart. These solutions include the point source solution (referred to in the field of hydrology as the Theis solution) and other solutions obtained with digital computer methods. With these curves, an exact evaluation of the pressure drop within a reservoir or an aquifer can be made by the engineer. Examples of field problem solutions are presented. In most reservoirs the error involved when the Theis solution is employed is often negligible; whereas, in the calculation of interference effects in an aquifer, a substantial error can occur through such an approach. INTRODUCTION Flow equations are used in petroleum engineering to study the behavior of individual wells and reservoirs. In the case of wells, the pressure response at the wellbore face is the major point of interest; whereas, in the case of reservoirs, the pressure response at the interface of the aquifer boundary is sought. To aid in such studies, the flow equations have been solved in terms of the behavior at these two inner boundaries. Only limited work has been published in regard to the pressure conditions away from these points, i.e., within the reservoir or aquifer. Theis and Mortada are among the few who have reported on this problem. The Theis approach employs the exponential integral and is valid for pressure conditions that occur some distance away from the flow disturbance. It is derived from the concept of a point source, as opposed to a flow across some finite area. The Mortada results, on the other hand, are valid at all points within the reservoir or aquifer. They are presented in terms of dimension less ratios of the radius where the pressure is desired to the radius where the flow rate is measured. Their main use, in the past, has been in aquifer studies. The published results are presented in the form of graphs that are limited to a maximum radius ratio of 64. These graphical results are cumbersome to interpolate at non-integral radius ratios, so that one may be forced to utilize a rather involved analytical expression presented by Mortada. BASIC EQUATIONS The solutions of Mortada and Theis are both based on the diffusivity equation as applied to the case of an infinite radial system subject to a constant terminal rate. The equation is obtained by combining the material balance equation with Darcy's flow equation. The assumptions implicit in the use of this equation are as follows: (1) a single fluid is present that occupies the entire pore volume; (2) the reservoir is horizontal, homogeneous, uniform in thickness, and of infinite radial extent; (3) compressibility and viscosity of the fluid remain constant at all pressures; and (4) fluid density obeys the equation Using the diffusivity equation in situations where the above conditions do not hold will result in errors. These errors (not discussed here) but only the errors which arise in the solution of the equation itself. The diffusivity equation for the homogeneous reservoir conditions cited above can be written in cylindrical coordinates, as To obtain a dimensionless equation, so a single solution can be used for applications of different porosity, permeability and fluid properties, the following transformations are usually made: After these transformations are made, Eq. 3 .can be written in dimensionless form, as MORTADA SOLUTION One solution of Eq. 6 has been given by Mortada.

Jan 1, 1966

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram for the gadolinium-cobalt system has been determined. Seven intermetallic compounds have been found at compositions corresponding to the follwing gadolinium-cobalt ratios: 3:1, 1:1, 2:3, 1:2, 1:3, 1:4, 1:5. The GdCor compound has a congruent melting point above 1600°C. whereas the remaining compounds melt incongruently. Eutectics exist at 16 wt pct Co and 84 wt pct Co, with melting points of 620° and 1260°C, respectively. PREVIOUS papers'" have recorded constitutional data for systems of gadolinium with iron and nickel. This paper presents data obtained on alloys of gadolinium with the remaining 3d transition element-cobalt. voge13 found that cerium forms, with cobalt, the intermetallic compounds; Ce3Co, CeCo, CeCo2, CeCo3, CeCo4, and CeCo5 Other workers4-' found the 1:2 compound in this series to exist in a C-15 (face-centered cubic) structure and the 1:5 compound to exist in a hexagonal crystal system. Comparison of earlier data with that now reported will be made subsequently. EXPERIMENTAL Methods of alloy preparation, annealing procedures, and experimental techniques have been previously reported.' The cobalt content of alloy specimens was determined volumetrically. RESULTS Microstructure—The alloy containing 10.5 wt pct Co corresponds closely to the composition of the first intermetallic compound Gd3CO. In Fig. 1 the microstructure is essentially single phase composed of Gd3Co which formed peritectically. The globular areas are remnants of the peritectic reaction which did not quite go to completion. A eutectic occurs between Gd3Co and the next higher compound GdCO, which is followed by a series of peritectic compounds. Fig. 2, an arc-cast alloy containing 20.2 wt pct Co, shows large primary crystals of GdCo etching either white or black (depending on crystallographic orientation), embedded in the eutectic. Similarly, in Fig. 3 at 31.2 wt pct Co, a compound, probably GdCo3, has separated from the melt. Subsequent peritectic reactions were almost completely by-passed as the alloy cooled, the residual liquid freezing as a fine eutectic. In the 47.5 wt pct Co alloy, Fig. 4, the high melting point compound, GdCO4, has solidified as massive, white-etching grains, which reacted with the liquid to form GdCo3 as the second phase. The microstructure of an arc-melted alloy containing 60.5 pct Co is complex, Fig. 5, and presents some difficulty in interpretation. The grey etching matrix is probably primary GdCO4. The dappled phase represents grains of GdCO5 which have separated from the melt on cooling. The discrete spots in this phase are eutectic liquid. Small light etching crystallites are probably GdCO5 formed by the incomplete high-temperature peritectic reaction. GdCO4 is retained in arc-melted specimens containing 70.5 wt pct Co, Fig. 6. White areas of this compound are held in a matrix of GdCO5 the appearance of which is mottled slightly by inclusions of the second eutectic in this system. The development of the spheroidized eutectic at high cobalt contents is depicted in Fig. 7 (80.3 wt pct Co) in which the white massive crystals are GdCO5 compound. Further development of this eutectic is seen in Fig. 8, the primary white phase here being pure cobalt. Thermal Studies—Differential thermal analyses and melting point determinations have yielded the data shown in Fig. 10. The high gadolinium eutectic, indicated by microscopy, was confirmed at about 16 wt pct Co, melting at 620°C . A eutectic also occurs at about 84 wt pct Co melting at about 1260°C. The thermal arrests at 8803 960°, 1060; and 1210°C,

Jan 1, 1962

By R. Taggart, D. H. Polonis, W. C. Gallaugher

In the Ti-Cu system, the a' phase can be produced over a wide range of alloy composition witJwut the retention of measurable amounts of the ß or ? phases. This paper reports on the decomposition of this hexagonal martensite phase front the standpoint of solute corzcentratiorz, tempering temperature, and coherency strain condition. The mechanism of precipitation during tempering comprises localized precipitation which is followed by discontinuous precipitation if sufficient coherency strains are present. The localized precipitation process in hypoeutectoid alloys is described by the generalized Johnson-hiehl equation and an activation energy of 46,000 cal per mole. In hypereutectoid alloys the corresponcEing activation energy is 51,000 cal per mole. The rate-controlling process has been proposed as the difision of copper along a' platelet interfnces. SEVERAL investigations have been reported concerning the kinetics of decomposition of the mar-tensitic a' phase in titanium binary alloys.' In the Ti-Mo system,' two modes of a' decomposition have been observed in the presence of /3 phase; one of these involves the precipitation of fine a from a', and the other involves diffusion across the a'-ß interface. In studies of the Ti-Cr system, Rostoker2 did not detect the formation of TiCr2 during tempering. In Ti-Ni alloys,3 the intermediate phase Ti2Ni has been found to precipitate directly from a' along the interfaces between plates. With the exception of the study of Ti-Ni alloys the previous investigations of tempering phenomena in substitutional martensites are mainly qualitative and do not present a detailed description of the precipitation processes. The following limitations restrict the correlation of the microstruc-tural processes and reaction kinetics during tempering in most binary-alloy systems. 1) A mixture of at least two phases characterizes the constitution of quenched alloys. 2) Difficulties have been encountered in obtaining uniform structures throughout quenched samples. 3) The reaction products, and in particular their morphology. have not been clearly resolved. 4) The martensitic a' phase forms over only a limited composition range for most titanium-base binary alloys. Gomez and polonis4 showed that the Ti-Cu system provides an excellent basis for investigating the tempering of a' over a range of composition without the complication of retained P or the transition w phase. In the present work the effects of solute concentration, tempering temperature, and coherency strain conditions are considered with reference to the over-all precipitation process in quenched alloys of the Ti-Cu system. Both microstructural observations and kinetic data are correlated to define the rate-controlling processes which govern the observed localized and discontinuous precipitation reactions. An earlier paper5 was devoted to a discussion of the modes of heterogeneous nucleation of Ti2Cu from the martensitic a' structure. The present paper will therefore emphasize the progress of the tempering reaction beyond the initial stages. EXPERIMENTAL METHODS The Ti-Cu alloys for this study were prepared by conventional arc-melting procedures. Chemical analysis revealed that the alloy buttons contained approximately 0.02 wt pct 0, 0.04 wt pct N, and within 0.1 wt pct of the intended copper concentration. The progress of the tempering reaction was followed by means of electrical-resistance measurements utilizing a Kelvin double bridge, microhard-ness readings with a 400-g load, and X-ray dif-fractometry patterns to reveal line-broadening effects. Metallographic specimens examined at magnifications greater than X1000 were shadowed with germanium to reveal fine structural details. Direct carbon replicas were prepared for the electron-microscopy studies. EXPERIMENTAL RESULTS Property Changes. The changes of microhardness that accompany the precipitation of Ti2Cu from a' are shown in Figs. 1 and 2. As the solute concentration increases the peak hardness, for a given tempering temperature, increases. In alloys of given composition the time to reach the peak hardness agreed with the time to attain maximum X-ray diffraction peak breadth, as shown in Fig. 3. The maximum hardness and the maximum line breadth increased with lower tempering temperatures, and the time to reach the maximum also increased. The a' peaks broadened during the initial stages of tem-

Jan 1, 1965

By T. M. Geffen, J. L. Sanderlin, F. F. Craig, D. W. Moore

Scaled reservoir models have been used to study the effect of gravity on oil recovery performance in frontal-drive operations; namely, water, gas, or solvent flooding. The difference in density between the reservoir oil and the injected fluid causes their segregation, resulting in a non-uniform advance of the fluid front. In the laboratory flow tests, which simulated both five-spot and linear injection operations in flat reservoirs, the viscous, capillary, and gravity forces present in these operations were scaled. Dyed fluids were used so that the gross movement of the injected fluid could be observed. The studies covered a range of injection rates, formation thicknesses, and rock and fluid properties normally encountered in field operations. The results of the model tests indicate that the volume of the reservoir contacted by the injected fluid at its breakthrough into the producing well is less than that expected based on information which neglects gravity effects. This difference can often be as much as 80 per cent by gas or water injection in uniform sand bodies. Preliminary flow tests on a non-uniform sand body indicate that the uniformity of the flood fronts may in some situations be influenced to a much greater degree by permeability variations within the rock body than by gravity effects. The magnitude of fluid segregation due to gravity is controlled by the average injection rate, rather than day to day or week to week variations. INTRODUCTION One of the important factors controlling the oil recovery from a frontal-drive operation, such as water, gas, or solvent injection, is the volumetric sweep efficiency. This factor is a measure of the gross portion of the reservoir that is contacted by the displacing fluid. The volumetric sweep efficiency is influenced by gravity effects, well arrangements, and variations in rock permeability within the reservoir. The gravity effects are due to the displacing fluid being of different density than the reservoir oil. This causes the displacing fluid to move preferentially toward either the top or bottom of the formation. Non-uniform advance of the flood front can be caused by the relative positions of the injection and production wells. Variations in rock permeability also result in an uneven advance of the displacing fluid. Gas zones, representing paths of low resistance, may result in non-uniform movement of the injected fluid. The more uneven the advance of the displacing fluid, the lower is the volumetric sweep efficiency and thus the lower the oil recovery efficiency. The effects of well arrangement and permeability variations, upon the gross movement of the injected fluid have been the subjects of extensive investiga-ti0ns.1,2,3,4,5,6 Gravity effects have been recognized as being present in frontal-drive operations'.' but there has been little quantitative measure of their magnitude. Very likely the reason gravity effects have not been studied is that this problem does not lend itself to simple experimental or mathematical analysis. The development of reservoir modeling techniques has made possible a quantitative determination of the effect of gravity on fluid segregation and thus upon the oil recovery performance of frontal-drive operations. This paper presents a progress report on a laboratory investigation of gravity effects in fully liquid-saturated, horizontal, uniform as well as non-uniform systems. These results were obtained from scaled experiments on both linear and five-spot systems within the range of conditions normally encountered in secondary recovery operations. This study is concerned with the gross movement of the injected fluid to the time it first reaches the production wellbore. Therefore, it should be emphasized that the results of this paper can not be used to determine the effect of gravity segregation on oil recovery efficiency at abandonment conditions. MODEL SCALING The science of scaling models is relatively new as applied as petroleum production problems, Many of the scaling techniques have been adaptions of those used in basic studies of heat and fluid flow. There are

Jan 1, 1958

By R. H. Edsal, G. Horvay

The transient one-dimensional heat-conduction equation is solved for two semi-infinite media, at different initial temperatures, brought into (poor) thermal contact. It is shown that the two interface temperatures gradually approach the well-known, instantaneously assumed, common interface temperature of the case of zero contact resistance. The present analysis, with slight modifications, may be used in fair approximation also for the class of problems involving a change of phase. One particular application of the boundary value problem solved in this paper concerns the determination of the temerature distribution in metal castings and molds.P This problem has been treated extensively by analytical methods (see e.g., the literature listed in Refs. 1 to 4) by electrical analogs (see e.g., Refs. 11 to 14) and also by experimental methods (see the literature listed in Refs. 4, 5), but prior to the work of Pellini and Ruddle the experimental results were rather unreliable. Immediate motivation for the work described in this paper was to better understand the results of Pellini,' which are typified by the curves of Fig. 1. Pellini cast 20-in. high, 7-in. sq steel ingots into cast-iron molds of various thicknesses. He measured the temperatures at mid-height, at a number of stations in the casting and the mold, and obtained the cooling curves shown in Fig. 1. The most conspicuous thing about Fig. 1 is the large temperature discontinuity at the interface between casting and mold, due presumably to the shrinking away of the casting from the wall and the attendant creation of an airgap, as the casting cools. Such a contact resistance slows down the anticipated freezing rate; an analytical prediction of this is of much interest in foundry practice. The determination of the effect of contact resistance in the presence of a change of phase will be dealt with, by an approximate method, in a separate paper.' In the present paper the much simpler problem is considered in which there is contact resistance but no change of phase. This problem frequently arises in the analysis of aircraft structures.+ It can initial temperature, and may be regarded as semi-infinite. We suppose the thermal properties in the two media to be time, temperature, and space independent; there are no sources or sinks within the media. In Fig. 2(a) we illustrate, schematically, the case of no contact resistance. The semi-infinite media "0" and "2:' initially at temperatures 8 (- m) and 8(+ -), respectively, are brought into contact at time t =0. A common interface temperature 8,i = is instantaneously established, and thereafter remains constant. Temperature curves are drawn for three instants of time. When there is contact resistance between the two media, the temperature equalization occurs as sketched in Fig. 2(b). Fig. 2(c) illustrates a temperature curve, using the dimension-less notation Barber-Weiner-Boley6 have stated the equations [23a, b] given below, which govern the heat transfer in the two media, and solved them for a rather complicated special case. In their example both media "O" and "2" are finite, are insulated at their far ends, and there is steady heat input into medium 2. In Eq. [27] we give the general solution of the most important special case, where the two media are semi-infinite and there are no sources or sinks. In this case the results may be stated in simple closed form. In Fig. 3, to be discussed in the next section, we illustrate the variation of the interface temperature when steel at 2760" is brought into contact with iron at 100". This example, if we disregard the effect of the heat of fusion, is comparable to Pellini's experimental results, Fig. 1. (Unfortunately, however, experimental determination of the interface temperatures was difficult to carry out, and hence Fig. 1 is not very accurate near the interface.) In Figs. 4 and 5 of the following section, we similarly compare Pellini's sandcasting tests with analytical results for the case where steel at 2760" is brought into contact with sand at 100". It will be pointed out that, insofar as the interface temperatures are concerned, heat of fusion has a minor effect, and so the present approximation, with small modifications, may be

Jan 1, 1961

By B. B. Rath, Hsun Hu

In wedge-shaped bicrystals of zone-refined aluminum it is observed that (111) pure tilt boundaries migrate under the driving force of their own inter-facial free energy. The boundary velocity is a power function of the driving force. The driving force exponent decreases with decreasing angle of misorien-tation. For example, at 64O°C, the exponent decreased from 4.0 for a 40 deg to 3.2 for a 16 deg tilt boundary. An evaluation of the driving force acting on the boundaries during their motion indicates that for low driv-forces, up to about 2 x l03 ergs per cu cm, the velocity is relatively independent of misorientation, whereas at higher driving forces a 40 deg tilt boundary exhibits the highest velocity. The measured activation energy for boundary migration approaches that for bulk self-diffusion at low driving forces, decreasing from 33 to 27 kcal per mole as the driving force is increased from 1 x l0 to 5 x l03 ergs per cu cm. These results are compared with current theories of grain-boundary migration. In previous experimental studies of grain boundary migration the driving force has been limited to a difference in stored energy across the boundary. This stored energy has been introduced into the crystal either by prior deformation1-3 or by grown-in lineage structure. A part of the energy stored in the deformed crystal is released by recovery either prior to or concurrently with grain boundary migration, thus introducing an uncertainty as to the magnitude of the driving force responsible for grain boundary migration. The grown-in lineage structure, though thermally stable during annealing, neither provides conditions under which different levels of energy may be stored in the imperfect crystal nor provides a control of orientation difference across the migrating boundary of a growing grain. Furthermore, because of variation in the lineage structure, it is difficult to determine accurately the energy stored in the imperfect crystal. Several investigations of grain boundary migration during normal grain growth have also suffered from difficulties in estimating the driving force because of uncertainties in the principal radii of curvature.~ In the present investigation the velocity of pure tilt boundaries in zone-refined aluminum bicrystals of selected orientation (40, 30, and 16 deg around the [Ill] tilt axis) has been measured in the absence of a dislocation density difference across the moving boundary, thus eliminating the previous experimental difficulties. The driving force for boundary migration is derived from a gradient of the total interfacial free energy of the migrating boundary in wedge-shaped bicrystals. A similar method was attempted by Bron and Machlin in a study of grain boundary migration in silver. However, they found that one of the crystals was deformed and consequently the motion of the boundary was partly due to a difference of stored energy across the boundary. The observed behavior of boundary velocities as affected by the driving force is examined in the light of the predictions of the current theories of grain boundary migration.7"10 The effect of boundary misorientation on velocity is compared with the theory of " which is based on a dislocation core model for high-angle boundaries. EXPERIMENTAL METHOD Seed-oriented bicrystals of zone-refined aluminum, 2.5 cm wide, 0.5 cm thick, and 12 cm long, containing tilt boundaries with a common (111) axis, were grown from the melt in the direction of this axis. Spectro-graphic analysis, reported earlier,'' indicated the purity of the crystals to be 99.999+pct. Three such bicrystals containing 16, 30, and 40 deg tilt boundaries were used. Wedge-shaped specimens were prepared from these bicrystals by spark cutting followed by electrolytic polishing. The angle of the wedge was usually 40 deg and the specimens were usually 0.25 cm thick. The intercrystalline boundary was located within 0.2 to 0.5 cm from the tip of the wedge. Fig. 1 shows a section of an oriented bicrystal containing an outline of a wedge-shaped specimen. The crystallographic directions shown in Fig. 1 represent the orientation of one of the crystals (the larger section of the bicrys-tal); the orientation of the other crystal differs only by rotation around the common [lil] axis. The parallel faces of the wedge always corresponded to the common (171) planes in both crystals, whereas the orientation of the side faces varied, depending on the misorientation angle. The bicrystal orientations were determined

Jan 1, 1970

By G. H. F. Gardner

The velocity and attenuation of elastic waves in sandstones were measured as a function of both pressure and fluid saturation. A large change occurs in these quantities if water is added and the rock is not compressed, but the change is small if the rock is subjected to a large overburden pressure. Measurements were made by vibrating cylindrical samples in both the extensional and torsional modes at frequencies up to 30,000 cycles/sec. Formulas were derived which enable the attenuation of dilatational waves in dry rocks to be deduced from the data. Similar experimental methods were used to investigate the properties of unconsolidated sands. Velocities were found to vary with the 1/4 power of the overburden pressure and attenuations to decrease with the 1/6 power. The effects of grain size, amplitude and fluid saturation were studied. Formulas by which the effects produced by a jacket around the sample may be calculated were derived. The practical application of these results to formation valuation is discussed. INTRODUCTION The attenuation of elastic waves in the earth has been of interest to the seismologist and geophysicist for many years, but only recently to the petroleum engineer. Engineering interest has been brought about by the success of velocity logging devices, for it is possible by modification of these instruments to measure the attenuation of sound waves in addition to their velocity and, hence, deduce the mobility of formation fluids as well as the porosities of the rocks which contain them. The main problem is to decide whether field measurements can be made with sufficient accuracy to be of practical use. This problem can only be solved after we know the magnitude of the attenuations which are typical of the earth at various depths. The logarithmic decrement of a fluid-saturated rock is the sum of a "sloshing" decrement and a "jostling" decrement, the former caused by the mobility of the fluid contained within the rock and the latter by the granular framework of the rock. Sloshing decrements can be calculated' using Biot's theory, but the jostling losses are less well understood. The present paper reports an experimental investigation of jostling losses in consolidated and uncon- solidated sands, particularly with respect to the effect of overburden pressure and fluid saturation. Born' showed that the decrement of a sandstone may increase dramatically when only a few per cent by weight of distilled water is added, and that the additional loss is proportional to the frequency of vibration. His measurements were made with no compressive stress on the framework of the rock. M. Gondouin3 investigated similar phenomena for fluid-saturated plasters but also did not compress the samples. In the present paper it is shown that compression of the framework reduces this effect, so that at depth the jostling decrement of a sandstone may be expected to be almost independent of fluid saturation and frequency. Decrements for many sedimentary rocks have been given by Volarovich,4 but all for the state of zero overburden pressure. Anomalously low velocities have been logged in shallow unconsolidated gas sands. Results of the present investigation confirm that these velocities are not caused by correspondingly high attenuations, because the jostling decrement in a packing of sand grains is small and much less than in a consolidated sandstone at the same depth. Velocities in sands have been measured by Tsareva5 and by Hardin6 as a function of pressure, but the corresponding decrements do not appear to have been measured previously. The widely used "resonant bar method" of measuring velocities and decrements was employed. Comments on variations of this technique have recently been published by McSkimmin.7 The main novelty of the present technique was the application of pressure to the samples. It was found possible to do this by placing the apparatus inside a pressure vessel, provided the conditions leading to large additional losses were avoided. These conditions are discussed below. EXPERIMENTAL TECHNIQUE Cylindrical samples were caused to vibrate in both the extensional and torsional mode of vibration and the amplitude of vibration was measured as a function of frequency in the neighborhood of a resonant frequency. The resonant frequency, fr, is related to the corresponding elastic modulus by the formulas where E and N are Young's modulus and the modulus of rigidity, p is the density of the sample, and A the wavelength of the vibration.

Jan 1, 1965

By Charles E. Lundin

Pressure-temperature-composition data were obtainedfor the Er-H system. Measurements werecar-ried out in the temperature range of 473° to 1223°K, the composition range of erbium to ErH,, and the pressure range of 10-5 to 760 Torr. Solubility relationships were established from these data throughout the system. Three solid-solution phases were delineated: metal solid solution, dihydride phase, and trihydride phase. The trihydride Phase decomposes at about 656°K and 1 atm pressure. The dihydride phase is stable to about 1023°K, but becomes more deficient in hydrogen above this temperature. The equilibrium decomposition pressure-temperature relationships in the two-phase regions, erbium solid solution plus dihydride and dihydride plus trihydride, were deter- The differential heats of reaction in these two regions are AH = - 52.6 * 0.3 and - 19.8 i 0.2 kcal per mole of Hz, respectively. The differential entropies of reaction are AS = - 35.2 * 0.3 and - 30.1 * 0.4 cal per mole HZ.deg, respectively. Relative partial molal and integral thermodynamic quuntities were calculated in the system to the dihydride phase. RARE earth metal-hydrogen systems have been the subject of general survey,1"4 and all have been found to form hydride phases. The heavy rare earths, of which erbium is a member, form dihydride and trihydride phases with different crystal structures, whereas the light rare earths form only a single-phase dihydride which expands without structure change, as hydrogen is added, to the trihydride composition. These materials are of interest primarily because of their theoretical properties, such as bonding, defect structure, and thermodynamic and electronic characteristics. Erbium has been studied in several previous investigations.5, 6 It was deemed desirable to more thoroughly and accurately define the system, both for the phase equilibria and the thermodynamic properties. I) EXPERIMENTAL PROCEDURE A Sieverts&apos; apparatus was employed to conduct the experimental measurements. Briefly, it consisted of a source of pure hydrogen, a precision gas-measuring buret, a heated reaction chamber, a mercury manometer, and two McLeod gages (a CVC, GM 100A and CVC, GM 110). Pure hydrogen was obtained by passing hydrogen through a heated Pd-Ag thimble. The hydrogen was analyzed and found to have only a trace of oxygen and nitrogen. A 100-ml precision gas buret graduated to 0.1-ml divisions was used to measure and admit hydrogen to the reaction chamber. The reaction unit consisted of a quartz tube surrounded by a nichrome-wound furnace. The furnace temperature was controlled by a recorder-controller to ±1°K. An independent measurement of the sample temperature in the quartz tube was made by means of a chromel-alumel thermocouple situated outside, but adjacent to, the quartz tube near the specimen. Pressure in the manometer range was measured to ±0.5 Torr and in the McLeod range (10-4 to 10 Torr) to ±3 pct. The hydrogen compositions in erbium were calculated in terms of hydrogen-to-erbium atomic ratio. These compositions were estimated to be ±0.01 H/Er. The erbium metal was obtained from the Lunex Co. in the form of sponge. The metal was nuclear grade with a purity of 99.9 pct +. The oxygen content was reported to be 340 ppm and the nitrogen not detectable. Metallographically the structure was almost free of second phase (<1 vol pct). A quantity of sponge was arc-melted for use as charge material. The solid material was compared with the sponge in the pressure-temperature-composition relationships. They were found to be identical. Therefore, sponge material was used henceforth, so that equilibrium could be attained more rapidly. The specimen size was about 0.2 grain for each loading of the reaction chamber. The procedure employed to obtain the pressure-temperature-composition data was to develop experimentally a family of isothermal curves of composition vs pressure. First, a specimen of erbium was wrapped in a tungsten foil capsule to prevent contact with the quartz tube. After loading the specimen, the system was evacuated to less than l0-6 Torr, flushed several times with high-purity hydrogen, and evacuated again ready for the start of the experiment. The furnace was then brought to the desired temperature. A measured amount of hydrogen was admitted into the chamber. Equilibrium was allowed to be attained, the pressure read, and the process then repeated many times until 1 atm of gas pressure was finally reached. Other isotherms were then developed in the same manner. The partial pressure plateaus were determined by another manner. In the solid solution-dihydride region a composition of approximately 1.0 H/Er was selected on the plateau. The temperature was varied throughout the range of interest. At each temperature level, equilibrium was achieved, the pressure read, and the next temperature attained. The temperature was cycled both up and down. In the dihydride-trihy-dride region, the plateaus were determined in the 473" to 651°K range only by heating to the desired temperature and not by both heating and cooling. The data were much more reproducible in this manner. Equilibrium required long periods of time. Specimens were initially hydrided to 2.8 H/Er, so that at the higher

Jan 1, 1969

By E. J. Rapperport, J. P. Pemsler

The thermodynamic activities of zinc in six solid solution Cu-Zn alloys ranging from 5 to 35 at. pct Zn were determined experimentally in the temperature range 400° to 600°C. This low temperature investigation was canducted in order to evaluate techniques developed to utilize the inherently high sensitivity of atomic absorption flocesses in the measurement of thermodynamic activities. Analytical expressions ,for the activity and actizlity coeflcient are given for the six alloys in the temperature ranges investigated. RELATIVELY few experimental methods are available for investigation of thermodynamic activities of alloys, especially in the solid state. The techniques most frequently used have been the electrochemical potential and the effusion methods, both of which have severe limitations in many instances. It is therefore desirable to expand the ability to perform such measurements in order to obtain new information as well as to provide an additional independent verification capability. In this work, we present a significant improvement in the spectrophotometric method for sensing small vapor pressures in static absorption cells. Similar techniques have been used previously;1"5 however, applications had been limited to relatively high pressures, often greater than 1 torr. Prior investigators have, for the most part, used broad spectral sources such as xenon or mercury lamps, and high intensity arcs. Hollow cathode sources were first suggested in 1956 6 and were used soon afterwards.4&apos;5 These sources offer significant improvements in sensitivity and freedom from interfering spectral lines.&apos;-&apos; EXPERIMENTAL High purity zinc was obtained from Cominco Products, Inc., and copper from American Smelting and Refining Co. Both elements were of 99.999 pct purity. Copper-zinc alloys were vacuum melted in a high fired carbon crucible with each alloy pulled from the melt as a 4 -in. diam bar. The bars were swaged to -1/4 in. rods and vacuum annealed for 160 hr at 800° + 1°C. Samples for gross chemical analysis were taken at intervals along the length of the rods to ascertain the axial zinc gradient. Electron microprobe analysis of homogenized specimens indicated that the alloys had uniform compositions over their cross sections on a macro (200 p) and micro (1 u) scale to better than *1 pct (20) of the gross composition. This tolerance was determined by counting statistics, rather than assured composition fluctuations. All SiO 2 windows were high-ultraviolet-transmission grade to minimize intensity losses. Silica absorption cells were scrupulously cleaned consecutively in organic solvents, dilute HF, and distilled water before use. The empty cells were then flamed while under a dynamic vacuum, cooled, and removed to an argon-filled glove bag. Alloy pieces were cut and filed in the glove bag to produce fresh surfaces, and then loaded into the cells. The loaded cells were temporarily sealed, removed from the glove bag, reevacuated to 10-5 torr or better, and permanently sealed. The instrument used is schematically shown in Fig. 1. The spectral emission from a commercially made hollow cathode lamp (A) of a selected element is focused through an absorption cell (B) inside a well-controlled furnace (C). The intensity of the transmitted beam is measured using the spectrometer* (D) &apos;Techtron model AA4 atomic absorption spectrometer. which contains a grating (E) that disperses the light prior to impingement on the photomultiplier (F). The monochromator grating is adjusted so that only the wavelength of interest is measured. The power supply delivered an interrupted voltage to the lamp, causing a chopped radiation output to be transmitted. The detector read only the intermittent component of radiation incident upon it, so that all continuous noise signals (furnace radiation, and so forth) were eliminated. Three recording thermocouples contained in the muffle furnace were positioned along the length of the absorption cell: one at each end and one at the center. An effort was made to keep the ends of the cell several degrees hotter than the center to avoid window condensate. Appropriate thermal corrections were then necessary to relate cell pressure to radiation attenuation. Water-cooled heat shields, as shown in Fig. 1, were found to aid signal stability by protecting the hollow cathode and the photomultiplier from furnace radiation. The furnace had a 2-in. diam muffle, Kan-thal wound, with SiO 2 windows at its ends to minimize convective effects. The hollow cathode radiation was masked and focused to form a conic beam that was a maximum of { in. diam within the furnace. Thus, the 1.5 in. diam absorption cell easily contained the entire beam. The furnace was mounted on ball-bearing slides with positive positioning detents. This arrangement allowed the removal of the entire furnace assembly from the radiation path, position [I], Fig. 1, so that frequent sampling of the unattenuated beam intensity could be obtained. In all cases the beam intensity was kept constant to 0.1 pct as judged by readings taken immediately before and immediately after data collection. Only data for absorptions of less than 80 pct were utilized, as systematic deviations from linearity were found for greater absorptions.

Jan 1, 1970

By P. H. Lindon, J. C. Billington

Fe-O melts containing 0.045 pct 0 were deoxidized with Mn-Si-A1 alloys. Product compositions were reluted to the melt and alloy compositions and were found to be most sensitive to the aluminum content of the alloy. Low residual oxygen contents could be obtained when aluminum oxide was present in the Products because of the reduction of silica and manganese oxide activities. Flotation of the Products from a quiescent melt was followed both by analysis of the oxygen content and metallographic measurement of inclusion concentration. MnO-SiO2-A12O3 products were found to float most rapidly when their composition was such that their viscosity may be expected to be low. Changes in the particle size distribution indicates that particle coalescence occurred and differences in the degree of coalescence are thought to be responsible for the different flotation rates observed between products 0f differing composition. Measured flotation rates were slower than those Predicted from a model based on Stoke&apos;s Law, although alumina flotation might be reasonably accounted for by this model. Interfacial effects between oxide particles and the melt are believed to be responsible for the discrepancy. It has been recognized that deoxidation products constitute a large proportion of the nonmetallic inclusions present in killed steel. The amount of oxide inclusions which originate as deoxidation products depends largely upon three factors. These may be summarized, according to P16ckinger1 as: 1) Amount of primary products remaining in the steel prior to cooling. 2) Residual dissolved oxygen content of the steel after deoxidation. 3) Amount of secondary products, formed during cooling and solidification, which remain entrapped in the solid steel. In a well-deoxidized steel containing residual aluminum and/or silicon, the equilibrium dissolved oxygen content is usually very low and so the maximum amount of oxide which may be produced as secondary deoxidation products is small in comparison with the amount of primary products. It may be seen, therefore, that the amount of indigenous nonmetallic inclusions may be minimized if a low dissolved oxygen content is achieved by deoxidation and if the primary deoxidation products are efficiently removed. Oxides which originate by reaction of the metal stream with the atmosphere during teeming are not considered in the present study. It is known that two or more deoxidizers may result in a lower equilibrium oxygen content when used in conjunction with one another than when any of the individual deoxidizers are used alone. Equilibrium studies by Hilty and crafts2 and by Bell3 have shown that manganese increases the effectiveness of silicon as a deoxidizer, and Walsh and Ramachandran4 relate this to a reduction in the activity of silica in the products as the manganese :silicon ratio in the steel increases. It was also shown by Herty&apos;s work on deoxidation of steel by silico manganese alloys,5 that there existed an optimum ratio of manganese to silicon which gave a minimum inclusion content. This ratio was in the range 4:l to 7:l and the (FeO-MnO-SiO2) products formed by such deoxidation practice were found to lie in a composition range having very low liquidus temperatures (1170 to 1250°C approx). The optimum manganese:silicon ratio was then explained by postulating that these fluid products were able to coalesce and that the larger particles formed floated out of the steel very quickly as predicted by Stoke&apos;s Law. The present work examines the effectiveness of various Mn-Si-A1 alloys as deoxidizers and their effects on the composition and removal of primary deoxidation products from a quiescent melt. EXPERIMENTAL TECHNIQUE Approximately 250 g of prepared Fe-O alloy, containing 0.045 to 0.055 pct O, were melted in an alumina crucible and deoxidized at 1550°C by plunging a thin steel cartridge containing the deoxidizer below the melt surface. A high frequency induction furnace supplying current at 8.5 kHz was used to heat a graphite susceptor, the interior of which had been machined to give a wall thickness of 0.85 in. to form a receptacle for the alumina crucible. The iron melt was essentially quiescent as the induced current was concentrated at the external surface of the graphite susceptor by the skin effect. A nonoxidizing atmosphere was maintained over the melt by passing a continuous stream of argon through the lid of the susceptor. The melt temperature was measured before deoxidation, and again at the end of an experiment by means

Jan 1, 1970