Search Documents

By Raymond D. Daniels, Frank E. Rizzo, James D. Gerber

ThIS discussion describes a method for the addition of small amounts of oxygen to columbium (niobium) in an accurate and reproducible manner. The method is based on the complete reduction by columbium of a carefully weighed amount of another metal oxide. The equilibrium Pq associated with Cb-CbO mixtures is extremely low, e.g., 10"25 atm at 100O°C, and the pressures over Cb-0 solutions are even lower. The equilibrium Pq associated with a given metal-metal oxide mixture can be easily obtained, with the aid of a Richardson-Jeffes chart.' Although columbium should effectively reduce almost any metal-metal oxide combination, the proper choice of a metal-metal oxide system is complicated by the low rate of oxygen transport in the gas phase at low oxygen pressures and the difficulty in reducing any columbium suboxide formed during the reduction of the oxygen source material. Thermodynamically, oxide formation on columbium will be avoided so long as the oxygen partial pressure over the columbium is below the equilibrium pressure associated with the mixture Cb-CbO. The logical choice of a source for oxygen would appear to be a mixture of Cb-CbO, since oxide formation would be precluded by nucleation difficulty. But calculations using the kinetic theory of gasses indicate that, for a temperature of 900°C, the reaction would proceed too JAMES D. GERBER, formerly Research Assistant, University of Oklahoma, Norman, Okla., is Research Metallurgist, Air Force Weapons Test Laboratory, Kirtland Air Force Base, N. Mex. FRANK E. RIZZO, Junior Member AIME, formerly Assistant Professor of Metallurgy, University of Oklahoma, is Associate Professor of Metallurgy, University of Texas at El Paso, El Paso, Tex. RAYMOND D. DANIELS, Member AIME, Professor of Metallurgical Engineering, University of Oklahoma, is an NSF Fellow, Institute de MBtallurgie Structurale, Universite de euch:tel, Neuchitel, Switzerland. Manuscript submitted October 28, 1968. IMD

Jan 1, 1970

By W. T. Hicks

Visual observation of the oxidation of columbium shows that the protective behavior noted previously in gravimetric work in the early stages of the reaction below 600°C and throughout the reaction at 640°C is associated with an adherent oxide. The fact that the oxide is seen to move outward from the metal at temperatures from 550° to 935°C implies that the reaction takes place at the oxide-metal interface throughout this temperature range. THE work described in this paper further clarifies the complex oxidation kinetics of Cb revealed, for example, by the continuous gravimetric studies of T. L. Kolski.1 Time-lapse motion picture studies reveal details of the reaction not provided by a study of the combustion products. EXPERIMENTAL PROCEDURE Cb specimens were prepared from material with the following typical analysis: 0, 0.03 pct; N, 0.002 pct; C, 0.006 pct; Ta, 0.04 pct; Fe, 0.01 pct; Ni <0.003 pct; and Cr <0.003 pct. Arc-cast ingots were swaged and cold rolled into slabs. These slabs were machined into blocks 7/16 by 7/16 by 7/16 in; 1/16-in. holes were drilled through the large face of the blocks for suspension. The samples were then de-greased and annealed 1 hr at 1200°C in vacuum. The sample was suspended by a platinum and Pt 10 pct Rh thermocouple inside a 1-in. quartz tube in a Kanthal wound furnace (2 in. OD by 4 in. long) equipped with windows 1/2 in. sq. A Cine-Kodak Special II 16 mm motion picture camera was trained on the sample through a Spencer microscope adjusted so that a magnification of X1.5 resulted on the film. Super Anscochrome film was used to record the events in color. Argon was flushed through the furnace while the sample came to temperature. The argon was then replaced by a stream of dry oxygen at 1 atm. Pictures were taken at the rate of eight per second for about 20 sec during the change of atmosphere. Then by use of a Stevens time-lapse device pictures were taken at the rate of four per minute starting within 1 min of the initial oxygen flow. In this manner continuous visual records of the oxidation of pure Cb

Jan 1, 1962

By R. Dawson Hall

The stresses in the simplest structures are often those we find most difficult to analyze. The most complex condition in mine stresses is found in simple tunnels where the roof, the sides, and the floor are a monolith. The functions of the parts are like the parts themselves not distinct and spccialized, and the problems to be solved are like those in a metal structure with riveted joints or a redundancy of bars. This difficulty explains perhaps why the condition has not been treated. But just because it cannot be discussed in its entirety is no reason why it should be treated as an action of parts with spccialized functions as a roof beam with supports and a foundation. The problern cannot be ignored on the ground that it is not of sufficient importance to warrant careful consideration, because conditions of complete monolithism, of which the tunnel is the type, are found materially unchanged in room-and-pillar and in longwall work. This unity between roof, sides, and floor, which to the coal miner is a difficult conception, really deserves a scientific appellation, and perhaps holoid (from holos, whole, and eidos, form) will serve the purpose as well as any other. In a simple tunnel the roof, the sides, and the floor form integral parts of one and the same structure, and the distortion of one cannot be conceived without a consequent strain in the others. Thus when the roof of the tunnel droops by reason of its weight, the upper parts of the sides are drawn in becausc they are integrally connected with the roof and must approach each other whenever, by the sagging of the roof, the distance between any two points in it is diminished. (See Fig. 1.) Thc sides in their turn operate on the floor of the holoid structure, producing a tensile stress. The writer has always been impressed with the value of soap as a means of illustrating the action of mine stresses. With that idea in mind&apos; a cake of naphtha soap measuring 43/8 by 2¼ by 19i in. was taken and a tunnel was made through it 13/4 in. long, 21/2 in. wide and 1¼ in. high. (See Fig. 2.) A load was then placed at the mid-span of the tunnel. Eventually, the upper bar, or "roof," broke at the

Jan 1, 1916

By James C. Bayles

The ideal pressure-tube is obviously the one which combines the greatest strength with the least weight of material consistent with the uses for which it is designed or employed. The inside of the pipe is the first concern of the engineer. It should be cylindrical, smooth, and of the requisite capacity for the purpose in view. It should be in lengths as great as can be oonveniently handled, so that the couplings may be as few as possible. With the walls of the tube the engineer has no further occasion to concern himself than to make sure they are adequate to carry the internal and external pressures to which they will be subjected. It is as true of a pipe as of a truss, that when it is strong enough to give the requisite factor of safety, nothing is gained by having it stronger. Anything more than this means dead weight, which has to be paid for many times, first as material, and again and again in the costs of transportation and handling, until it reaches its place in the trench or on supports. In use it must be and remain tight against all leakage, and must sustain whatever is placed over or upon it, or suspended from it, without deformation or injury. Finally, in addition to meeting all the immediate requirements of service, it must possess qualities of durability which warrant a reasonable expectation of a long life of usefulness. The wise engineer no longer regards it as reasonable to depend upon mere bulk of its own material for the protection of a metal as readily impaired or destroyed by oxidation as iron or steel. The metal must have a coating which will be and remain impervious and indestructible. When all these conditions are met, we have as near an approach to the ideal tube as can be attained with the materials now available for their manufacture. Steel wed constructively, to the best advantage, meets these requirements most perfectly. Gold alone would do it better. If we search through the whole list of metals and alloys we find nothing available which so perfectly meets the requirements as a pipe material as steel. Mr. Hamilton Smith, Jr., in a paper on the expedients adopted on

Jan 1, 1891

By P. de Vitry, Oliver Bowles

THE conventional wire saw, introduced in the slate district of Pennsylvania by the Bureau of Mines in 1927, and used thereafter with remarkable success, consists of a three-strand steel cable having a diameter of 3/1 6 or 1/4 in. The equipment, methods used, and accomplishments have been described in previous reports.1-7 Similar wire saws have been used extensively in Europe, in quarries and in shaping blocks and slabs. During the period 1932-1937, competition in European marble quarries was keen, prices were declining, and orders were not abundant. When orders were received, there was generally an urgent call for speedy delivery. Because of the diversification of demands, it was impossible. to maintain in stock marbles of the color, size, and thickness called for,, therefore the material generally had to be fabricated after the order was received. The wire saw enabled stone mills to fill. such, orders promptly. With skillful handling, 7/8-in. slabs could be cut accurately and rapidly with this equipment. It was found, however, that, as the three-strand wire became worn, the cutting speed dropped rapidly and the cut became less accurate. To overcome these difficulties the junior author of this paper, after much experimentation, developed a new type of wire consisting of a single ribbon-shaped strand, twisted as shown in Fig. I. To ensure straight sawing, the twist of the ribbon is reversed from right to left and vice versa every 25 ft. The reversal of the [ ] twist is shown in Fig. 2. This is not a new feature; it has been used to advantage with the three-strand wire both in Europe and America for several years. However, some difficulties arise in splicing the three-strand reverse-twist wire, and the claim is made that cutting is less accurate as the wire becomes worn. To make an endless belt, the ends of the single-strand wire are brazed together with

Jan 1, 1941

By J. L. Rodda, M. L. Fuller

In connection with an investigation in this laboratory on the high-zinc side of the copper-zinc system, it was observed that well developed segregate structures of the Widmansttten type were formed when a secondary phase precipitated from the solid solution of copper in zinc. This paper presents an analysis of the crystallographic relationship between the segregate and the solid solution matrix. The data to be presented are an interesting addition to the literature on segregate structures in that the plane of segregation is one of the less densely populated planes. In agreement with the generalization of C. H. Mathewson and D. W. Smith&apos; the plane of segregation in the matrix contains the direction of closest atomic packing of the lattice. Furthermore, the matrix and the segregate are both hexagonal close-packed, which has not been reported hitherto in the 1iternture.l The increasing commercial importance of zinc alloys containing copper makes this fundamental study of value to the metallography of zinc alloys. Zinoeich Copper-zinc Alloys Copper enters into solid solution with zinc to at least 1.8 per cent at 400" C., according to W. M. Peirce.3 The solubility is less at lower temperatures. Thus a solid solution of copper in zinc, saturated at an elevated temperature, will precipitate the excess copper in a separate phase at a lower temperature, conditions of concentration, time, and temperature being suitable. The nature of these two phases has been established by the X-ray method of crystal analysis. Westgren and Phmgmén4 and also Owen and Preston5 have shown that the solid solution eta (7) is of the substitu-tional type with copper atoms replacing zinc atoms on the hexagonal

Jan 1, 1933

ONE of the interesting-though not unnatural-features of the whole Porphyry Copper development is the way in which the history of each property dovetails with that of one or more of the others. The same names keep cropping up as one digs into the accounts of events from 1900 to 1915. J. Parke Channing made examinations of Nevada, Ray, and Inspiration, as well as of Miami. Henry Krumb did important work in the early stages of the exploitation of Utah, Nevada, Ray, Braden, and Inspiration. Pope Yeatman was favorably impressed with the Braden property before he had ever visited it, when he saw a batch of Braden ore sent to the United States for testing. It reminded him immediately of Nevada Consolidated ore: indeed, he was unwilling at first to believe that it came from South America. And it was while working on the examination at Utah Copper that Philip Wiseman became enthused with the possibilities of the Ray mines. In 1905, Mr. Krumb, under the general direction of A. Chester Beatty, was strenuously engaged at Bingham, Utah, in arriving at an answer to this question: Should or should not the Guggenheim interests back Jackling to the tune of several million dollars to build the big concentrators at Gafield? Seeley W. Mudd was the Guggenheim engineer on the Pacific coast and in that capacity was indirectly responsible for the work at Bingham. At his suggestion Wiseman came up from Los Angeles as one of Krumb&apos;s assistants-at $5 per day, incidentally. A little later Mr. Mudd, in Utah on one of his visits, went down to Bingham. That evening in the old Hills Hotel in Markham Gulch he was going over reports with Mr. Krumb. Wiseman and some of the other engineers on Krumb&apos;s staff were present. During a breathing spell, Mudd expressed

Jan 1, 1933

By Edward G. Norton

The salt deposits of the Mississippi Embayment region present a problem of origin so genetically related to the larger problem of the stratigraphy and structure of the region that a discussion of the one necessarily involves or assumes an understanding of the other. For this reason, I shall summarize briefly our knowledge of this region, emphasizing the facts related to the subject of this paper. In so doing I shall make liberal use of the reports of the National and State surveys. Geographically that section of the United States known as the Mississippi Embayment region represents a great V-shaped area, extending from near Cairo, Ill., to the Gulf of Mexico, and including Louisiana, eastern Texas, all that part of Arkansas bordering the Oua-chita and Ozark mountains, western Tennessee, Mississippi, and a part of Alabama. This great section Professor Harris has described as structurally a pitching trough, its medial line being well represented by the Mississippi River. Outcropping along the border of this area are the Cretaceous and Tertiary formations, unconformably laid down on the hard Paleozoic rock sheets that show more or less plication, deformation, and faulting, depending upon their proximity to the nearby major uplifts. East and west of the Mississippi River the Cretaceous and Tertiary beds dip river- and coastward at angles greater than the slope of the land. "Waters entering along the outcropping edges of the Tertiaries and Cretaceous and following bedding planes southward are soon thousands of feet beneath the surface." As the sedimentation of the region progressed, faulting and slips occurred along planes of pre-Cretaceous weakness. Whether these movements were genetically related to the loading of this V-shaped area, as Professor Harris seems to think, is a question still to be settled. The accompanying map, Fig. 1, was taken from Bulletin No. 7 of the Louisiana- Geological Survey. It shows the regional distribution of the salines, as well as an alignment of the domes, which has been assumed to indicate faulting.

Jan 1, 1915

By W. H. Craigue

THE scope of this article covers only the mathematical principles involved in discounting to present worth future expected profits and it is believed answers definitely two questions, which were raised at a recent meeting of the Committee on Methods of Valuing Coal Properties, as follows: 1. The accumulative effect of carrying charges on the value of coal mines showing definitely the number of years beyond which the coal may not be mined at a profit and subsequent to which the possession of any unmined coal will be a liability rather than an asset. 2. The effect on the valuation of coal mines, in the presence of the carrying charges described in question 1, of an increase in plant capacity and production. In general, in considering these questions, it may be stated that the consideration of an increase in plant capacity and production follows as a matter of course after a determination has been made of the year beyond which no profits are to be realized (giving the carrying. charges accumulative effect, or in other words capitalizing the carrying charges, as shown hereinafter). For example, if it is determined that any coal that is unmined after 45 years will have no value or less than no value, the question immediately arises as to whether or not a plant should be constructed that would result in a yearly production great enough to extract the entire tonnage in a time less than 45 years, and if so the number &apos;of years less than 45 years that would, from a financial stand-point, be the most desirable, all under the assumption that the market for the product or the transportation facilities are such that the yearly production can be increased to the desired amount.

Jan 1, 1933

By W. S. Gresley

The traces of fossils herein described were discovered in or upon piles or heaps of iron-ores upon the docks at Erie, Pa. The author has worked among these ore-piles since 1890, when his attention was first directed to what looked like organic remains upon certain specimens collected. All the specimens described and figured herein were found by him, and, as no ironore is used at Erie, and no other iron-ores, save those of the Lake Superior region, find their way to the stock-piles at this place, there can be no question but that the specimens in question are genuine ore transported from that region over the great lakes, and cannot have been brought in from other ironore regions. The author has reason to think that no fossil remains have been reported hitherto as occurring in the iron-ores of the Lake Superior region, and he believes that these specimens, however imperfect, rank among the oldest forms of which man has any knowledge. The illustrations are engraved from photographs of drawings. The specimens themselves have not been photographed, because their condition would have prevented bringing out, by that process of reproduction, all the markings as clearly as is necessary, and would have rendered the specimens otherwise less distinct by reason of the blotchy character of their colors, the presence of cracks, or of marks more or less in contact with those of the organisms. In drawing these remains, therefore, I left out everything upon the specimens of ore that did not seem to belong in any way or contribute to their value as illustrations of the fossils. According to information obtained from the dock superintendent at Erie, Pa., the majority of these specimens came from the Chapin mine, Iron Mountain, Menominee range, Mich. As to the rest of them, I stupidly failed

Jan 1, 1897

By D. A. Schemnitz, O. W. Ellis

Certain alloys1 that, as a result of quenching, are retained in the form of homoaeneous solid solution are known to increase in hardness and strength on standing at room temperature or on heating at slightly elevated temperatures. Other alloys2 that, on rapid cooling, are held in the form of homogeneous solid solution, as, for example, certain steels, behave in like manner on heating to somewhat higher temperatures. The observed increase in the hardness and strength of these alloys, referred to as " aging"&apos; or as "secondary hardness," is widely accepted as being occasioned, either in whole or in part, by the precipitation in submicroscopic form of such constituents as were held in supersaturated solid solution as a result of cooling in excess of a certain critical rate. In earlier discussions of the cause of age hardening or secondary hardness, the question of the hardness of the precipitated particles does not appear to have been raised. At present, however, the general opinion appears to be that age hardening and secondary hardness are occasioned by the precipitation of hard particles within the supersaturated solid substance.3 The authors may be wrong in their belief that the last is a prevailing opinion. Nevertheless, it is thought that the following experiments,

Jan 1, 1925

By Eugene A. Stephenson, Leon J. Pepperberg

The natural gas industry is essentially a byproduct of the oil industry. When first discovered the gas was usually regarded as a nuisance, and even when found immediately associated with oil, or suspected to be so, it was customary to blow it freely into the air, in the hope that gas would shortly be replaced by a flow of oil. The early methods of production,&apos; transportation, and utilization were neither economical nor efficient; the chief value of gas was based on its use as a fuel, with no regard to (1) its effect. upon the oil with which it was associated, (2) its importance as a lifting agent, or (3) to its possibilities for the manufacture of byproducts. The spread of scientific research among major gas and oil companies, manufacturers, and academic groups, has gradually brought recognition of the fact that many of the technical problems bearing on production, transportation and utilization are common to both the gas and the oil industry. A few of the problems that have received serious study, and from which highly gratifying results have been obtained, are: (1) gas measurement, (2) oil well and gas well capacity tests, (3) elimination of field waste, (4) design of pipe lines and compressor stations, (5) extraction of constituents which might interfere with the normal flow of gas through the line, (6) control of reservoir pressure, (7) estimation of reserves of both oil and gas, (8) control of water encroachment, (9) measurement of factors which influence fluid movement through sands, (10) solubility of gases in oils, (11) effect of dissolved gases upon the properties of the solution. These investigations have demonstrated that almost every problem relating to oil production also involves some phase of natural gas engineering. During the past 15 years the use of experimental methods for the discovery and measurement of obscure, influencing factors, which cannot be determined purely by hydrodynamic or thermodynamic analyses, have contributed much towards the progress made in solving the problems of the oil and gas industries. Most of the experimental work on

Jan 1, 1934

By Miguel Bustamente

In 1890 I mas manager of a mining enterprise in the State of Michoacan. The ores were composed principally of iron pyrites (much decomposed), in a quartz matrix, with native gold in very irregular grains. Some portions, however, carried their metallic value in a matrix of calcite arid siderite. The mill in which the ores were treated consisted of two 800-lb. stamps, two amalgamating-plates, four pans, two automatic washers, two Frue vanners, and the necessary accessories for assaying, retorting and refining gold. The plant, originally erected with American capital, and directed by competent Americans, passed in 1890 into the hands of Mexican owners. On taking charge of the business I found on hand a large amount of ore assaying 35 grammes of gold per metric ton (about 1 oz. Troy per ton of 2000 lbs.); but the company was losing money, and was about to abandon the business. Obviously, the difficulty lay in the treatment of the ore. The extraction of gold scarcely reached one-tenth of the assayvalue ; the loss of mercury was considerable; and high freight; charges excluded the alternative of exporting the ores. This situation naturally suggested that amalgamation was not applicable to these ores, and that a more appropriate method must be adopted. The cyanide- and chlorination-methods had been tried already, without practically satisfactory results. For the first few months I employed a combined system, extracting a part of the gold by direct amalgamation, and cyaniding the concentrates. This saved 32 per cent. of the assay-value, but the cost of milling still exceeded the proceeds. Meanwhile I observed

Jan 1, 1902

By Morgan Walker

ONE of the most serious problems in the produc- tion of natural gas is the removal of water from the wells. As a gas well approaches its period of exhaustion, the removal of water by properly de-signed devices becomes increasingly important. Sev-eral methods are used for dewatering gas wells. If the .gas velocity and pressure are high enough, the water in the well will be carried out by the gas on opening the well to atmospheric pressure and allowing the gas to flow unrestricted except for the resistance of the casing. This method of dewatering a gas well is detri-mental to the producing sand, and very wasteful if used frequently. When the well has declined in production a string of tubing is often run in the well, with a packer set at the top or bottom of the well. If the top of the tubing is opened to atmospheric pressure and the gas is allowed to flow unrestricted as in the above method, the water can be discharged at the top of the well, provided the velocity of the gas is high enough. However, if the water has accumulated in the well until the water pres-sure is equal to or greater than the gas pressure, the ,water cannot be brought to the surface. In dewatering :a gas well by this method the operator sometimes finds -that if the packer is set near the top of the well and -the casing is tight, the water can be blown out when .it is impossible to blow it out with the packer set at the top of the sand. This is largely due to some gas leaking into the tubing through the collars. This method of dewatering gas wells is also wasteful. Water can be pumped out of a gas well with virtually the same equipment, as used for pumping oil, but the method involves installing a separate pump for each well, and difficulties are encountered in attempting to pump water under high gas pressure.

Jan 3, 1927

By H. W. Kropholler, L. A. Cramer, E. T. Woodburn, J. C. A. Greene

A generalized mathematical structure is proposed whereby internal species mass flows within a flotation network are defined uniquely by a matrix of enhancement factors. An element of the enhancement factor matrix is defined as the ratio of the mass flow of that species leaving a given cell in the concentrate to the species mass flow leaving the same cell in the tailings. To predict the enhancement factors, knowledge of flotation kinetics effects is required. Recently experimental data has become available relating to the performance of industrial flotation circuits which indicate that the discrete or discrete-distributed kinetic schemes are capable of reasonably effective simulations. These simulations show the importance of including froth effects. The prediction of performance of networks from small-scale batch tests on flotation streams shows that the model for the froth phase used in the simulations does not scale-up well and that aeration effects are also difficult to predict. The network analysis should be useful in differential flotation of complex ores and it is disappointing-in this context that little information on the kinetics of activation and depression is available.

Jan 1, 1976

To the American Institute of Mining Engineers: The committee appointed at the February meeting upon Railway Resistances would respectfully report: That one person has been constantly employed in calculating the results of the data taken prior to March 1st, 1876. Also to complete the data taken upon the Lake Shore and Michigan Southern Railway, a diagram was taken upon a through freight train from Cleveland to Chicago, and one from Chicago to Cleveland. So that now we have diagrams from Buffalo to Chicago and return, which, when fully worked up, will give results of the utmost importance in determining the cost of transportation of freight. These data will be of much importance in determining the proper methods of equating grades and curves, which is so essential in the location of new lines. The calculations show that instead of our attempting to formulate results from data obtained on one road, it will be best for the interests of transportation to enlarge the scope of our inquiries, and to extend the experiments so as to include all of the more probable causes which affect the cost of transportation. Were the details of railway equipment constructed alike, much work, which is now necessary, would be saved. It is not uncommon to find upon the same road 10 to 30 different patterns of something in construction to subserve the same purpose, which more or less modifies the friction of the cars. Take the majority of our trunk lines, with this diversity of construction, together with the varying conditions of track and manner of operating, and it will be at once seen that the labor and time to do the work and arrive at correct conclusions will occupy from two to three years. The results already attained in the short time in which they have been carried on, wholly by private enterprise, simply show what may be expected when the aid necessary is given to render them of the highest value to the great industries of the country. That the information may be general and of the greatest importance to our railway interests, the committee deem it advisable to secure, so

By Basil Prescott

In the science of evolution of the species, there is a law which, simply stated, avers that the history of the individual repeats the history of the race. Similarly, if unassisted by the experience of others, each SUCcessful engineer would perfect and develop his methods and technique from the rough grab sample up to the carefully taken, recorded and studied samples and observations which now determine and decide the expenditure of the large sums required for modern mining. Hence real progress results from the interchange of experience, as in that way the entire experience of the profession can be made available to every engineer. The literature of this subject is already voluminous, but some progress has been made in the gathering of data and in their compilation or presentation. More Romance than Developed Ore in Limestone Deposits In certain types of deposits, methods little known 25 yews ago have been developed, perfected and standardized to a degree that lifts sampling from the field of manual labor to the plane of an applied science; for instance, the modern methods of estimating the so-called porphyry coppers. With some types of orebodies, we have become familiar, and sometimes on too easy speaking terms, with millions of tons of ore in reserve and tens of millions of dollars; while with others even these once marvelous figures sink into insignificance before the array of ciphers that are presented. .In such company, the average limestone replacement orebody is entirely out of place, for its reserves seldom reach a figure to arrest the attention of the modern engineer, and more often are insignificant. It is only when the records of the production of some of the older camps are studied, which show them to have continuously produced over very extended periods, that a realization is borne home that occasionally this type is worthy of consideration even in these days of gigantic tonnage.

Jan 1, 1925

By F. W. Sperr

The byproduct coke oven is the most important artificial source of fuels for metals melting. Its products are solid, liquid, and gaseous in form. The amount of coke and primary byproducts obtained per ton of coal varies with the nature of the coal. The following represents the results obtained in many plants: Metallurgical coke (over 3/4 in.).............................. 69 per cent. of coal Domestic coke (1/2 to 3/4 in.)................................ 2 per cent. of coal Breeze (under 1/2 in.)...................................... 4 per cent. of coal Surplus gas, cubic feet per net ton........................... 6600 Gas for heating ovens, cubic feet per net tor i................. 4400 Tar, gallons per net ton.................................... 9 Ammonium sulfate, pounds per net ton....................... 25 Benzols, gallolls per net ton................................. 4 All of these products, except ammonium sulfate, have important fuel value. Part or all of the metallurgical coke may be crushed or screened to furnish additional domestic coke. If producer gas is used, there will be a surplus of 11,000 cu. ft. of coke-oven gas per net ton of coal. The use of coke in the metallurgical industries has been retarded by the mental attitude of writers who disregard the dependence of coke quality on the conditions of its manufacture. Terms like "byproduct coke," (&apos;beehive coke," "48-hour coke," and "72-hour coke" are only generally descriptive and tell nothing of the coke quality. For example, one writeri stated that in brass-foundry practice, Connellsville coke is considered rnuch superior to byproduct coke on account of the high sulfur content of the latter. Another2 says, "At equal prices for hard Connellsville coke and for byproduct coke at the foundry door, the hard coke is unquestionably cheaper. It will melt more metal per ton than the byproduct coke and requires less labor, as the byproduct coke is less dense and burns faster, thus requiring more frequent firing." A little study of the conditions under which coke is manufactured will show the error in making general statements like these. The percentage of sulfur in coke depends largely on that in the original coal, and byproduct coke from a

Jan 1, 1921

By C. A. Eligwe, F. W. DeVries, A. E. Torma

This study is an investigation on using hydrogen peroxide for tank-leaching of uranium with sulfuric acid. The optimum sulfuric acid concentration was found to be 0.03 mole 11 -&apos;for a 25% pulp density suspension. The order of reaction with respect to sulfuric acid concentration was found to be ns0.75. The best results vith hydrogen peroxide were obtained at a 4.64 molar ratio of 6202 to U in the ore. The order of reaction was found to be zero with respect to hydrogen peroxide concentration. The theoretical maximum rate effect of Hz02 on uranium extraction was derived as Vm = 8.15 x mole &-&apos;min-&apos;. The highest rate experimentally attained was 8.09 x mole kL&apos;min-&apos;. It was found that the uranium extrac- tion was not affected by the pulp density up to the 50% used in this study. However, the final yieldswere significantly higher (over 90%) for leaches carried out in the presence of Hz02 than (less than 90%) for leaches carried out in the absence of H202. The reaction was found to follow a first order course with respect to substrate concentration (pulp density) regardless of the presence of H202. The effect of temperature was more explicit at moderate tempetatures (30 to 55 C) than at lower (10 C) or at higher (70 C) temperatures. At this latter temperature an almost complete extraction was realized even without H202. The apparent activation energies were found to be AEa = 2.68 kJ mole-&apos; in the absence of H202, 0.5 kJ mole-&apos;with Hz02 at 40 C to 70 C. and 4.72 kJ mole-&apos; with Hz02 at 10 C to 40 C. All these activation energy values suggested that the uranium extraction process is diffusion controlled regardless of the presence of H202. Further, the change in activation energy in the presence of Hz02 indicates the possibility of change in the reaction mechanisms at lower and higher temperatures.

Jan 1, 1980

By Howard S. Bryant

The state of Kansas in 1931 continued to hold fourth place on the list of oil-producing states, despite the fact that low prices for crude oil curtailed drilling to just one-half the amount done in 1930, which itself was the lowest in the preceding 10 years. The estimated crude oil production for 1931, according to sources available to the writer, will approximate 37,037,000 bbl., the lowest since 1925. Thus Kansas produced one-eighth less oil this year than it did last year when it produced 42,729,085 barrels. This year&apos;s development was characterized by a very small amount of wildcat drilling; however, large new areas were semiproven for oil production, and several thousands of acres were added to the actually proved areas in western Kansas, so that the state now has larger proven areas of oil reserves than at any time in its history since the heyday of the famous El Dorado pool. The general prospects for oil production in the near future are indeed promising for central western Kansas, where drilling costs are moderate and depths are relatively shallow compared to the remaining unexplored parts of the northern Mid-Continent area. Probably the greatest singular achievement in the state for 1931 was the development of its natural gas reserves. This development took place principally in two spots, McPherson County in central Kansas, and Stevens and Morton counties in southwestern Kansas, and it is a matter of record that more than one and one-half billion cubic feet of open-flow capacity per day were added to reserves, nearly twice the amount developed in 1930, previously the largest amount in the history of gas development in Kansas. Gas pipe lines already built and now building are in position to deliver natural gas by one system to Chicago, Ill., by another to Indianapolis, Ind., from whence lines already lead practically to the Atlantic seaboard, and to other cities large and small located west, northwest, north and northeast of Kansas. Table 2 shows all well completions for 1931 in a form to compare with the results of previous years.

Jan 1, 1932