Search Documents

By M. T. Simnad, C. E. Birchenall, M. H. Davis

The transport mechanisms previously proposed in wustite and hematite have been confirmed by movement of inert markers during the growth of these phases. By similar measurements the mechanism for magnetite has been determined. The rates of growth of multilayer scales on iron, magnetite and hematite on wustite, and hematite on magnetite have been measured. All rates are found to be diffusion controlled under the conditions of the experiments. MANY studies have been made of the rate of oxidation of iron in both the low temperature, film-forming region and the high temperature scaling range. The interpretation of the results has been greatly complicated by the formation of multi-layered scales containing the various phases of iron oxides. In most cases no attempt has been made to determine the composition of the scale and its dependence on time of oxidation in a quantitative manner. However, several recent studies'" have taken this variable into account. It is generally agreed that the growth of thick scales on iron follows a parabolic rate law for the increase of total thickness. In the thin film region agreement has been claimed with parabolic equations of various forms and with logarithmic equations. The discussion here will be concerned only with the formation of scales of considerable thickness, greater than several microns, although some of the conclusions may be applicable to thin films. A brief survey will be given of the solid phases of the iron-oxygen system, the stability of wiistite in bulk and in thin films, the relative densities of iron in the metal and oxides, and the kinetics of forma- tion of oxide scales on iron. New experimental results will be introduced at several points during the discussion, and an attempt will be made to formulate a mechanistic picture consistent with these observations. The experimental techniques are described in an appendix. Iron-Oxygen System Fig. la shows the iron-oxygen phase diagram. Wüstite ("FeO"): The lowest of the oxides has a NaCl type cubic lattice formed by close-packing of the relatively large oxide ions with the smaller iron ions arranged in the interstices. The ionic radius for 0' is about 1.3 A, while Fe++ has a radius of about 0.8A and Fe"' about 0.7A. Its range of existence on the phase diagram is very wide for an ionic material of this type and does not seem to include the stoi-chiometric composition FeO. These deviations appear to be well established as vacancies on iron lattice sites by the comparison of lattice parameters and densities for a series of compositions by Jette and Foote.4 The limits of the field are disputed, but the work which seems most reliable" indicates vacancies in from 5 pct to more than 12 pct of the iron sites. In order for the crystal to be electrically neutral, there must be electron holes which correspond to the formation of trivalent iron ions equal to twice the number of vacancies. Magnetite ("Fe³O4"): Considerable disagreement also exists in the literature about the stable range of the Fe³O4 field. Some diagrams show the Fe³O4 composition to be lower in oxygen than the formula indicates, but Schenck6 gives a diagram from the

Jan 1, 1952

By Jasper L. Stuckey

It is not known when kaolin mining was first begun in North carolina, Evidence, in the form of excavations and primitive tools, indicates that some of the deposits were worked in prehistoric times. It has been suggested that the prehistoric mining was for mica, but the workings were all in altered or partly altered pegmatite material and the dumps do not represent the amount of material removed. some of the early openings may have been made in search of kaolin or semi-kaolinized feldspar which was sold to English1 traders along the coast and used in some Of the early English porcelains. In 1744,2 an application was made for an English patent to produce porcelain from an earthy mixture obtained from the Cherokee Nation in North America. It is well established, however, that the occurrence of kaolin in western North Carolina was known in England by 1767. In that year, Josiah Wedgewood sent T. Griffiths3,4 to what is now Macon County, North Carolina, to secure a supply Of kaolin for use in England. Griffiths diary, now in Etruria Museum, Stokes-on-Trent, contains a most interesting account of his experience. Kaolin was discovered at St. Austell, England, shortly after the voyage Of Griffiths, which probably accounts for the lack of further interest in American kaolin. Between 1767 and 1888, there are no records of kaolin mining in North Carolina. In the latter year, however, mining was begun near Webster, Jackson County, and, in the intervening period, has become an important industry. 'Or some 20 years, kaolin mining was carried On chiefly in Jackson, Macon, and Swain Counties. About 1904, it was begun in the Spruce Pine district and for the past 20 Yea's most of the kaolin mined in the State has come from Avery, Mitchell, and Yancey Counties. Distribution The kaolins of North Carolina are limited in occurrence to the Piedmont Plateau and Appalachian Mountain area of the State. While kaolins are widespread in the Piedmont Plateau, having been prospected for in Rutherford, Cleveland, Gaston, Granville, Lincoln, Catawba, Ire-dell, Richmond, Moore, Randolph, and Montgomery Counties, the production from that area has never been important. The known deposits of commercial importance are limited entirely to the mountain area of the State. While kaolins occur widely distributed throughout the mountain area and have been prospected for in many counties of that area, commercial production has come chiefly from two districts. One of these includes Jackson, Macon, Swain, and Haywood Counties. The other includes Avery, Mitchell, and Yancey Counties. Geology With few exceptions, all the known kaolin deposits in North Carolina contain

Jan 1, 1948

By E. V. Potter, H. C. Lukens

The volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.² Both sets of data show a minimum solubility between 500' and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. Therefore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. Apparatus and Method The apparatus and method were essentially the same as those described in the previous work,' as shown in Fig. I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transi- . tion points determined under such conditions were less accurate. Absolute Solubility Procedure ad Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1947

By T. A. Rickard

The province of Otago consists, roughly speaking, of the southern half of the South Island* of New Zealand. On three sides it is washed by the Pacific Ocean and on the north it abuts against Westland and Canterbury. It covers an area of over 20,000 square miles, and for the most part has an extremely broken surface; the narrow plains of the sea-board are bounded by the rounded foothills which in turn are overlooked by range after range of the snowy summits whose varied beauty has made the island known as the Switzerland of the southern hemisphere. The gold-fields are confined to the quartzose schists which, in a broad band, 70 to 75 miles wide, cross the district, extending in a northwesterly direction from the shore of the western ocean into the northern provinces. These quartzose schists are the characteristic rocks of Otago, and to their curious structure are due the interesting differences exhibited by the mining districts in the modes of occurrence of the gold. These rocks, which are almost unbroken over their full extent, have been divided by the Provincial Geologist, F. W. Hutton, into two series of beds, named respectively the Wanaka and Kakanui formations. The only reason given for this division is the desire " to divide such an enormous thickness of rocks in order that the map might display somewhat of the geological structure of the district." As Hutton and others have pointed out, there is in fact no dividing line. The changes noticeable in the ascending series of schists are very gradual, and are due to the slowly decreasing effects of metamorphism. Hutton estimates the thickness of the Wanaka series at as much as 50,000 feet, and the

Jan 1, 1893

By C. C. McDermond

In reviewing petroleum development in Venezuela during the year 1936, it is well to bear in mind certain factors that affected progress, although not directly connected with the oil industry itself. At the start of the year, when the present Federal Administration took over the reins of government, reaction against the former regime resulted in some popular uprisings. Although these were entirely political in character, they were not without their effect on the oil industry itself. Such popular agitation really ended with a short general strike in Caracas, Maracaibo and other cities during June, these strikes being based on demands for certain changes in government policies. The strikes were duly investigated and their motives taken into consideration by the executive power or by Congress, and during the year many of the civil, political and administrative laws have been revised. In June and December, however, it was necessary to suspend activities in drilling and production work, particularly in the Lake Maracaibo Basin area. In June a strike caused a five-day shutdown in the main producing fields and on Dec. 14 labor difficulties resulted in a shutdown that continued to the end of the year, which necessitated suspension of all drilling and production in the Lake Basin area and curtailment of shipments to deep-water terminals. Actually, the strike lasted for a period of 42 days, until Federal intervention brought the dispute to a close with minor wage increases to workers hut with no loss of initiative or independence on the part of the oil companies. Operations in eastern Venezuela were not affected by the labor disturbances, production and exports having been reduced in December only in the Lake Basin fields. Well Completions On Jan. 1, 1937, a total of 3384 wells had been completed throughout Venezuelan fields, as compared with 3094 on Jan. 1,1936. Of these wells, 2005 were producers. The 290 completions effected during 1936 were by the following operating companies: Lago Petroleum Corporation, 123 completions; Dutch Shell group, 104; Standard Oil Company of Venezuela, 46; Mene Grande Oil Co., 15; British Controlled Oilfields, Ltd., 2.

Jan 1, 1937

By B. D. Thomas

GRAVITY concentration is a general term designating processes for separating and sorting granular material by means of forces that depend on the density, size and shape of the particles. When these forces are applied to the particles the latter are caused to move, those of a given density along one path and those of a different density along another, until ultimately they are sufficiently separated to be removed from the operation of the process. The forces producing this separation are in general complex and, unfortunately, no completely rigorous analysis of them has as yet been devised. The science of the hydrodynamics of viscous fluids deals with the little that is known about the problem. Every observer of nature is familiar with the fact that an object moving in a fluid encounters a force of resistance. We have only to walk against a brisk wind or stir a cup of coffee, or observe the slow fall of a grain of sand in water, to experience directly the fact that such forces exist. The exchange of force between an object and a fluid in which it is moving operates on the fluid as well as on the object. Thus a sailboat may be set in motion by the force exerted by the wind on the sail; but the sail also deflects the wind-furthermore, the water in which the boat floats is set in motion by the force exerted by the boat as it cleaves through the water. The wind is thus enabled to do work on the water through the intermediary of the boat. In general, an object moving through a fluid encounters a force that opposes the motion and also acts to change the motion of the fluid. In gravity concentration we are dealing with this force of resistance acting - on the granular particles that are to be separated. Furthermore, the motion induced in the fluid by a particle will in turn affect the motion of a neighboring particle. This effect will be reciprocated and in consequence there will be an exchange of forces between all the particles in the material. These effects are complex and the most that can be expected is that we may be able to determine in a qualitative way how they operate. In gravity concentration, then, the following types of forces may be distinguished as acting on the particles: 1. The force of gravity, which acts on every particle in the system in proportion to its mass. 2. Buoyant forces, which arise from the force of gravity acting on the fluid.

Jan 1, 1950

By H. H. Stoek

Mine models have three distinct uses: 1. As exhibits in expositions and museums. 2. As exhibits in law suits. 3. As illustrations in teaching mining engineering. All three uses are in a sense educational. The third, or distinctively teaching function, has not been extensively developed in America as it has been abroad, chiefly because of the cost of the models and the scarcity of model makers. In connection with expositions, such as the Columbian, the Louisiana Purchase, and the Panama-Pacific, a number of very good mine and metallurgical models were prepared with funds furnished by State commissions, by mining organizations or mining companies. At the close of these expositions, some of these models have been deposited in National or State museums or in educational institutions, but too many of them haw been lost, or have been stored away in some mining company's office or in the basement of some State building, where they have been lost sight of and have gradually fallen to pieces. A visitor to a German mining school is impressed by two facts: 1. The mining laboratories are in general inferior to those in America. 2. The mining museums are infinitely superior to ours, particularly in models exhibited. One may reply to this comparison by saying that a museum is necessarily a work of time. From the historical standpoint this is, of course, true, but it is not necessarily true in connection with a working museum intended to illustrate current practice. For instance, the oldest mining school in Germany, that at Freiberg, has much excellent historical material, but very little on modern practice, while Berlin, one of the youngest German mining schools, has a most extensive and valuable collection of modern appliances and models. This is true in spite of the fact that one of the best-known model shops is at Freiberg, from which many of the models to be seen in America have come. Because many of the models in American mining schools have come from

Jan 1, 1918

By Bruce F. Grant, Stefan F. Szasz

During 1947, a Sinclair research team was assigned to investigate thermal methods of oil recovery. The assignment was recommended by a survey of possible research approaches to increase the amount of oil that ultimately can be recovered from oil producing reservoirs. The use of heat to stimulate oil production rates by the melting of paraffin deposited in well bores can be traced back to within one or two decades of the drilling of the Drake well. The application of heat on a larger scale has been discussed by generations of oil producers. Shortly after the turn of the century, one intrepid operator is reported to have injected steam into a Pennsylvania property. After a few weeks, he apparently became discouraged and terminated his experiment. Subsequently, the literature contains references to several well-developed techniques for supplying heat to a producing well bore to melt paraffin or to reduce the viscosity of oil contained in the formation immediately around the well bore.1.?.3.4 Some early references discuss procedures to furnish heat to the reservoir,5,6 with the injection well as the heat source, thus obligating the process to maintain the entire rock mass at a temperature above that at which the desired improvement in oil recovery would occur. Another approach to reservoir heating was reported by a group of Russian technologists in 1935.7,8,9 They definitely demonstrated that combustion can occur within the porous structure of an oil-bearing sandstone. Their field experiments, however, relied less on combustion within the rock than on heat furnished by combustion of oil supplied to the injection well bore. Ignition of the air-oil mixtures in the well bore was found very difficult, and the field tests were carried on for only short periods of time. Publication of the Russian work spurred at least one independent operator in this country to try firing an air-gas injection well, on for only short periods of time. Publication of the Russian work spurred at least one independent operator in this country to try firing an air-gas injection well. The Brundred Oil Corp. reportedly obtained combustion in the sand immediately around the injection well bore, but the experiment was abandoned because of interference with normal production schedules. Injection capacity of the experimental well was greatly reduced by firing. The well was reshot and pieces of sand showing partial fusing of the quartz matrix were recovered. To the authors' knowledge no other field experiments utilizing combustion techniques for formation heating were undertaken prior to 1948, although the patent literature evidences continued interest in formation heating."'," CONCEPT OF COMBUSTION-SUPPORTED HEAT WAVE The references cited were in agreement that heat applied to a reservoir would increase recovery, but there

Jan 1, 1955

By J. E. Hilliard

It is proposed that shape anisotropy in the internal structure of materials be defined by distribution functions which specify what fraction of the total line length or boundary area lies in a given direction. Methods are descriibed for determinirg these distribution functions from measurements on sections through an opaque material. New derivations, that have certain advanifages over those given previously, are Provided for well-known expressions used in estinzating the total density of lineal or areal features. INCREASING attention is being given to the quantitative description of imicrostructures in metals and other materials. This interest stems from the recognition that the structure often provides a convenient half-way point between the properties on the one hand and the processing variables on the other. Such cross correlations become increasingly desirable as materials become more complex and the demands on them more stringent. One of the principal aims in structure analysis is therefore to find parameters that are readily measurable and specific enough to be correlated with other properties of the material. Certain properties, such as magnetic and mechani cal behavior, are strongly influenced by structural anisotropies; in order to relate such properties to the structure it is obviously necessary to have means of specifying and measuring the type and degree of anisotropy. For the determination of preferred orientations in crystal structure, X-ray diffraction methods are available and are widely used, but scant attention has been given to the estimation of anisotropy in the shape of grains and particles. It is the latter problem that will be considered in this paper. It is evident that shape anisotropy can be describe in terms of preferred orientations of lineal and area elements of the structure. It will be shown that these preferred orientations can, in turn, be specified by distribution functions that define what fraction of the total line length or boundary area lies in a given direction. Methods will be given for determining the distribution functions from measurements on sections through the structure. Even when the orientation distributions are of no interest per se, they still have an important bearing on the measurement of the total line length or boundary area by means of an intercept analysis. The treatment in terms of orientation distribution functions leads to new derivations, that have certain advantages of those given previously, for the well-known expressions used in estimating the total density of lineal or areal features. The treatment is divided into two main sections. The first deals with the orientation distribution of a two-dimensional array of lineal features such as occurs in the projected image of dislocations in electron transmission microscopy. The other section treats the estimation of the distribution of lineal and areal features dispersed in three dimensions.

Jan 1, 1962

P. E. McKinney,* Washington, D. C.-Observation made after examination of a number of defective gun forgings, together with a history of their manufacture, has strongly suggested that so-called "flakes" and woody or fibrous fractures are not necessarily analogous and are often caused by entirely different conditions. While some flaked bars may show fibrous areas in the fracture, it does not necessarily follow that the conditions causing these areas are the same as cause the fibrous, or so-called laminated, structures so commonly met in gun forgings subject to transverse tensile test; the fibrous structure formed in some flaky bars are merely incidental to the conditions causing the flakes. It is believed that the so-called flakes, or bright silvery spots, are mainly due to inherent physical defects in the steel, which existed at the very origin of the steel, rather than metallographic defects caused by subsequent irregularities in mechanical or thermal treatment. While great care in forging and treatment may, in a measure, tend to overcome the evil effect of the defects, with many heats of ingots, no such precautionary measures are needed to produce perfect forgings- and with such heats of steel it would be impossible, no matter how carelessly handled, to produce intentionally a forging containing the defects commonly known as flakes. It has been found possible, on several occasions, to actually predict flaky forgings from an inspection f the ingot after it had solidified, and in such cases no amount of careful forging or heat treatment would prevent the occurrence of such defects in the forging. The inspection of the physical condition of the ingot, and especially the character of the shrinkage on. the top of the ingot, has been given too little thought and study in this connection.

Jan 5, 1919

By David B. Burrows, Rlkl Kobayashi, Norman L. Carr

The viscosity of hydrocarbon mixtures, whether in the gas or liquid phase, is a function of pressure, temperature, and phase composition. This paper presents methods for the prediction of the viscosity of the gas or less dense fluid phase over the practical range of pressure, temperature, and phase compositions encountered in surface and subsurface petroleum production operations. The correlation necessary to predict the effect of pressure on viscosities is presented in Part I. Serious discrepancies in high pressure gas viscosity data in the literature are discussed. The application of the correlation to predict absolute viscosities is discussed in Part 11. Auxiliary correlations are presented to enable calculations of viscosities from a knowledge of the pressure, temperature, and gravity of the gas phase. INTRODUCTION A knowledge of the viscosity of hydrocarbon fluids is needed to study the dynamical or flow behavior of these mixtures through pipes, porous media, or more generally wherever transport of momentum occurs in fluid motion. Since flow is predominantly in the laminar region in petroleum reservoirs, the influence of fluid viscosity on this flow is especially important. As early as 1894, Onnes1 and Onnes and de Haas' noted that the viscosities of homologs under corresponding states could be correlated. The theorem of corresponding states has been further developed and applied to the viscosity of pure, nonpolar gases under pressure by Comings, Mayland, and Egly.3 It was demonstrated that the viscosity ratio could be expressed rather closely as a function of reduced pressures and temperatures, 1.e.: µ/µ1 = f( TR2 PR) ........(1) temperature, absolute units where: TR =------------------------------ ------ critical temperature. absolute units _pressure, absolute units critical pressure, absolute units µ = viscosity of gas at reduced temperature TR and reduced pressure PR µ1 =. viscosity of gas at atmospheric pressure and at temperature TR Serious discrepancies in the viscosity of pure hydrocarbon gases at high pressures have been called to Our attention by Comings, and and Egly. They made a careful analysis of the following methods commonly used to measure gas viscosities: 1. Oscillating disc viscometer4,5 2. Rolling ball viscometer6,7 3. Capillary tube viscometer12 On the basis of their analysis of the problem and their experimental data on the viscosities of methane, ethylene, carbon dioxide, and propane, they preferentially selected data obtained by the capillary tube viscometer to develop their viscosity correlation. Since then a need has existed to verify the experimental technique of Comings, Mayland, and Egly for the determination of viscosities at high pressure; to extend the data to mixtures of hydrocarbons; and to extend the range of their correlation to include higher pressures. Using the correlation procedure of Comings, May-land, and Egly, the prediction of gas viscosities is resolved into the correlation of the effect of pressure, temperature, and composition on the viscosity of hydrocarbons and their mixtures and the prediction of viscosities of mixtures of hydrocarbons and other natural gas components at one atmosphere pressure.

Jan 1, 1955

By J. S. Crump, C. R. Hocott, A. E. Hoffman

Planning of the efficient operation of a gas-condensate reservoir requires a knowledge not only of the gross phase behavior of the system but also of the equilibrium distribution of the various components between the gas and condensate phases. This equilibrium distribution can be calculated with appropriate equilibrium constants. In this paper are presented equilibrium constants determined experimentally for the oil and gas phases initially present in the same reservoir and for the gas and condensate phases of the gas cap material at a series of pressures below the original reservoir pressure. Also presented is a method for the correlation of the experimentally determined equilibrium constants. The utility of the correlation is demonstrated further by an example of its use in adjusting the equilibrium data to permit their application to another gas-condensate system of similar composition. INTRODUCTION Planning of the efficient operation of a gas-condensate reservoir requires a thorouugh knowledge not only of the gross phase behavior of the particular hydrocarbon system but also of the equilibrium distribution of the various components between the gas and condensate phases. At the initial conditions of reservoir temperature and pressure, the original hydrocarbon materials in a gas-condensate reservoir or in the gas-cap of an associated reservoir exist in a single, homogeneous vapor phase. However, some condensation of hydrocarbons to a liquid phase usually occurs in the reservoir as pressure declines incident to production. Because of this condensation. the produced gas changes composition continuously. The composition of the produced gas, as well as that of the condensed liquid, can be calculated from the composition of the original reservoir material through the application of appropriate equilibrium constants or "K"-values provided these values are known. Equilibrium constants have been used for many years in problems of surface separation of gas and oil and natural gasoline recovery. However, no satisfactory equilibrium data at reservoir conditions have been available for the higher boiling hydrocarbons which acquire abnormal volatility at high pressure and are therefore present in the gas phase in condensate reservoirs. Early work in this field indicated that the behavior of the higher boiling hydrocarbons largely determines the behavior of gas-condensate systems at high pressure.' Consequently, a portable test unit was designed to permit determination of the distribution of the heavier hydrocarbons between the gas and liquid phases of a gas-condensate system. This paper describes the test equipment and presents the results of an investigation of the reservoir fluids from an associated oil and gas reservoir in the Frio formation in Southwest Texas. Also presented is a method for correlation of the experimentally determined equilibrium constants, together with an example of the use of the method in adjusting these data for application to another gas-condensate system of similar composition. FIELD TESTING AND SAMPLING In order to determine the compositions of the reservoir fluids, field samples were secured from two different wells, one completed in the oil zone, and one completed in the gas cap. The oil well was completed through perforations in 51/2-in. casing at a depth of 6,822-6,828 ft subsea. Pressure and temperature traverses made in the well indicated the pressure and temperature to be 3,831 psig and 201 °F, respectively, at a depth of 6.828 ft subsea. Subsurface samples were taken from this well after a four-hour shut-in period.

Jan 1, 1953

By Charles R. Austin, Carl H. Samans

In an earlier serics of studies on 18-8 stainless steel at 600º, 700º, and 800ºC.l one pretreatment was used throughout; viz., 15 min. in hydrogen at 950°C., followed by an air quench. Several manufacturers of this alloy since have expressed doubt as to the suitability of the temperature employed, recommending instead the more customary Strauss treatment as promising superior results. In this subsequent investigation on the effects of the temperature of pretreatment several interesting points have arisen, which are described in this paper. Previous work on our equipment had shown a marked difference between alloys of "similar chemical composition" that had been manufactured by different companies. Accordingly, one mill-bar length was selected from which to prepare all specimens. It could then be assumed that any marked differences in creep characteristics would be due to effects resulting from variations in the pretreatment of the alloy. The material was furnished by the Allegheny-Ludlum Steel Co. in the form of 5/16-in. dia. rod, finished by air cooling from a mill anneal at 1950°F. (1066°C.). It was analyzed only for the elements shown: carbon, 0.07 per cent; chromium, 18.73; nickel, 9.46; manganese, 0.40. Three pretreating temperatures were chosen, the specimens being held for 15 min. in hydrogen at either: (1) 1150°C., to conform to the recommended Strauss treatment; (2) 950°C., to compare with the results of previous tests; or (3) 75Q°C., to initiate precipitation of carbides in the material before testing. As the test cross sections were only 1/8-in. dia., air cooling followed the annealing treatment. These treatments permitted two direct comparisons: (1) between the 1150" and 950°C. treatments to indicate the effect of grain size when all carbides were probably in solution at the start of the test; and (2) between the 950" and 750°C. treatments to indicate the effect of carbide "nucleation" for similar grain sizes.

Jan 1, 1940

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938

By A. M. Kivari

Operations at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hy-droseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the mallufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. † About 3I30 tons of limestone, 620 tons of clay and I00 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. up to the present time, the ccrporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modihed-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Red- ding, Calif., the total demand being 5,800,000 bbl. of cement. Following are some of the cement require ments of the Shasta Dam specifications: Per Cent Chemical composition: Loss in ignition.......... 2.25 Insoluble residue......... 0.75 SO3.................... 2.25 MgO................... 5.'' Uncombined lime in clinker (CaO)......... I.25 Percentage of iron oxide to alumina ratio....... I.5 Compound composition: Tricalcium silicate (3CaO.SiO2)........... Not more than 35 Dicalcium silicate (zCaO.SiO2)........... Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O3).......... Not more than 7 Tetracalcium aluminofcr- rite (4CaO.Al²O³.Fe²O³) Not more than 20 Fineness: The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1942

By E. C. Wright

The bessemer process is nearly one hundred years old. William Kelly, the American inventor, was able to demonstrate that he had accomplished the pneumatic purification of molten pig iron as early as 1847; Henry Bessemer's English patent was granted in 1855. The application of this steelmaking process since then and the present position of bessemer steel are concisely discussed on pages 355 and 356 of the fifth edition of "The Making, Shaping and Treating of Steel." The great expansion of the automotive, machine-tool, chemical and oil industries after I9I0 opened up a large market for special steels, whereas the output of steel before that time was mainly for structural purposes. The need for building more blastfurnace capacity complementary to bessemer operations, combined with the availability of the' necessary amounts of steel scrap, both contributed to the extension of open-hearth plants at the -exense of besskmer capacity. The ability of the open-hearth furnaces to consume virtually all types of raw materials as far as phosphorus content is concerned, and the need for selecting low-phosphorus ores of rapidly decreasing sources for the bessemer, also played a part in the reduction of bessemer steelmaking operations and the increase in basic open-hearth plants. As a consequence, the proportion of bessemer steel made, in this country decreased from 65.7 per cent of the total in 1900 to 37.1 per cent in 1910, and only 6.8 per cent of the total in 1937. The metallurgical concepts existent between 1910 and 1920 caused the writing of many specifications of very low phosphorus and sulphur content, which definitely barred bessemer steel from many commodities. Now sulphur is being added to many open-hearth and bessemer steels in amounts far exceeding the maximum sulphur content of good bessemer steel. Re-phosphorizing is also widely practiced for several specific applications. Even today, the chemical-analysis limits of many important steel specifications have an arbitrary and archaic tinge. The old standard "0.30 to 0.60 per cent manganese" might be mentioned in this connection as similar to the rigid requirements for maximum sulphur and phosphorus that were established at least 25 years ago. The literature is full of vague and complee discussions of the effects of nitrogen and oxygen where these elements existed in steel in amounts less than 0.02 per cent. Many failures have been attributed to these elements without reasonable proof on which to base the conclusion. Methods of determining oxygen in steel require such complicated equipment that only a few research laboratories have the required apparatus. Even so, the accuracy of oxygen determinations in steel has been only recently reproducible. Up to the present time, no one has succeeded in obtaining a sample of molten steel that accurately indicates the full oxygen content of the metal in the furnace or ladle because the molten sample

Jan 1, 1944

By Nicholas J. Grant, John Chipman

A full understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization;the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag—i.e., equilibrium conditions—and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck:20 V radio = % CaO/%SiO, Körber and Oelsen's _ % CaO'. 100/% CaO + % SiO2 where (%CaO') = % CaO- 1.18% P2O5. Herty's B ratio = % CaO - (0.93 . % SO2) - (1.18% P205) Among others there appear the following: 20 References are at the end of the paper.

Jan 1, 1947

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938

By Carl H. Samans, Charles R. Austin

In an earlier serics of studies on 18-8 stainless steel at 600º, 700º, and 800ºC.l one pretreatment was used throughout; viz., 15 min. in hydrogen at 950°C., followed by an air quench. Several manufacturers of this alloy since have expressed doubt as to the suitability of the temperature employed, recommending instead the more customary Strauss treatment as promising superior results. In this subsequent investigation on the effects of the temperature of pretreatment several interesting points have arisen, which are described in this paper. Previous work on our equipment had shown a marked difference between alloys of "similar chemical composition" that had been manufactured by different companies. Accordingly, one mill-bar length was selected from which to prepare all specimens. It could then be assumed that any marked differences in creep characteristics would be due to effects resulting from variations in the pretreatment of the alloy. The material was furnished by the Allegheny-Ludlum Steel Co. in the form of 5/16-in. dia. rod, finished by air cooling from a mill anneal at 1950°F. (1066°C.). It was analyzed only for the elements shown: carbon, 0.07 per cent; chromium, 18.73; nickel, 9.46; manganese, 0.40. Three pretreating temperatures were chosen, the specimens being held for 15 min. in hydrogen at either: (1) 1150°C., to conform to the recommended Strauss treatment; (2) 950°C., to compare with the results of previous tests; or (3) 75Q°C., to initiate precipitation of carbides in the material before testing. As the test cross sections were only 1/8-in. dia., air cooling followed the annealing treatment. These treatments permitted two direct comparisons: (1) between the 1150" and 950°C. treatments to indicate the effect of grain size when all carbides were probably in solution at the start of the test; and (2) between the 950" and 750°C. treatments to indicate the effect of carbide "nucleation" for similar grain sizes.

Jan 1, 1940

By E. C. Wright

The bessemer process is nearly one hundred years old. William Kelly, the American inventor, was able to demonstrate that he had accomplished the pneumatic purification of molten pig iron as early as 1847; Henry Bessemer's English patent was granted in 1855. The application of this steelmaking process since then and the present position of bessemer steel are concisely discussed on pages 355 and 356 of the fifth edition of "The Making, Shaping and Treating of Steel." The great expansion of the automotive, machine-tool, chemical and oil industries after I9I0 opened up a large market for special steels, whereas the output of steel before that time was mainly for structural purposes. The need for building more blastfurnace capacity complementary to bessemer operations, combined with the availability of the' necessary amounts of steel scrap, both contributed to the extension of open-hearth plants at the -exense of besskmer capacity. The ability of the open-hearth furnaces to consume virtually all types of raw materials as far as phosphorus content is concerned, and the need for selecting low-phosphorus ores of rapidly decreasing sources for the bessemer, also played a part in the reduction of bessemer steelmaking operations and the increase in basic open-hearth plants. As a consequence, the proportion of bessemer steel made, in this country decreased from 65.7 per cent of the total in 1900 to 37.1 per cent in 1910, and only 6.8 per cent of the total in 1937. The metallurgical concepts existent between 1910 and 1920 caused the writing of many specifications of very low phosphorus and sulphur content, which definitely barred bessemer steel from many commodities. Now sulphur is being added to many open-hearth and bessemer steels in amounts far exceeding the maximum sulphur content of good bessemer steel. Re-phosphorizing is also widely practiced for several specific applications. Even today, the chemical-analysis limits of many important steel specifications have an arbitrary and archaic tinge. The old standard "0.30 to 0.60 per cent manganese" might be mentioned in this connection as similar to the rigid requirements for maximum sulphur and phosphorus that were established at least 25 years ago. The literature is full of vague and complee discussions of the effects of nitrogen and oxygen where these elements existed in steel in amounts less than 0.02 per cent. Many failures have been attributed to these elements without reasonable proof on which to base the conclusion. Methods of determining oxygen in steel require such complicated equipment that only a few research laboratories have the required apparatus. Even so, the accuracy of oxygen determinations in steel has been only recently reproducible. Up to the present time, no one has succeeded in obtaining a sample of molten steel that accurately indicates the full oxygen content of the metal in the furnace or ladle because the molten sample

Jan 1, 1944