Search Documents

By L. Valentik

Many attempts have been made during the last 40 years to evaluate the performance of gravity separation equipement, that is, the effectiveness with which light and heavy particles are separated. The most comprehensive treatment of the subject was made by Cerchar at the 1st International Conference on Coal Preparation held in Paris in 1950. The methods suggested by the Conference were accepted and very widely used in the last two decades. This paper discusses an improved method of evaluation in the light of the now-accepted standard presentation. The float-and-sink analysis of the product is presented on a Gaussian distribution curve, resulting in an easier visualization of the inherent difficulties of separation. The ogives of the distribution curve me then plotted, giving a quantitative measure of the deviation from perfect separation as an error distance instead of an error area. Illustrations of the new method are given both for gravel and for coal preparation, but the content is valid and applicable to other types of minerals which are separated by gravity methods. Many attempts had been made during the last forty years to evaluate the performance of heavy-media separation (HMS) equipment, that is, the effectiveness with which floats and sinks are separated.'-' The most comprehensive treatment of the subject was made by Cerchar at the 1st International Conference on Coal Preparation held in Paris. 6 The primary aim was the thorough understanding of the mechanism of separation and the unified presentation of data on gravity separation so that the evaluation and comparison of washery performance could be made from all over the world. No strict overall standardization has been achieved, but after the conference a more or less uniform presentation of performance was accepted, which, during the last two decades, has been very widely used. In this paper, illustration of the old methods and an improved method of evaluation will be given. HEAVY-MEDIA SEPARATION (HMS) PERFORMANCE CRITERIA In the ideal HMS process, all material lower in density than the specific gravity of separation (SGS) would be recovered as floats and all material of higher density would appear as sinks. In order to evaluate the misplaced material, the washery products are tested at the density at which the washing unit is operated. The original type of plot1,7, 8 is shown in Fig 1; this was developed primarily for coal cleaning units. The curve for raw coal represents the cumulative percentages of sink material. The refuse curve is also plotted as a cumulative sink, the percentages being expressed in terms of raw coal. This diagrammatic representation of the results of washing units has the merit of easy visual observance of the degree of separation obtained. The error areas (cross-hatched) are a measure of the amount of misplaced material and therefore they can be used to characterize the quality of separation. The ideal and actual separating performance between floats and sinks can be best seen from the partition curve developed by Tromp,2 where the ordinate is the percentage recovery of the sinks, and the abscissa is the specific gravity (Fig. 2). It can be seen from the shape of the curve that as the SGS is approached, the proportion of material reporting to the improper product increases rapidly. In fact, the SGS can be defined as the density of the material in the feed that is distributed equally between float-and-sink products. When the upper half of the curve is inverted, a shape similar to that of a Gaussian error distribution curve is obtained and therefore the analysis of gravity separation may be carried out by using the law of probability. The shape of the curve in Fig. 2 is determined partly by the density composition of the feed, and partly by the sharpness with which the unit separates floats from the sinks.9, l0

Jan 1, 1970

By W. F. Kieschnick, C. C. Miller, E. R. Brownscombe

The possibility has been mentioned that large pressure gradients in a solution gas driven field caused by high production rates might lead to a reduction in the ultimate recovery obtainable compared to that which would be obtained by a very slow rate of production. In the present study the reservoir conditions accompanying a high rate of production and the corresponding ultimate recovery were compared with those obtained if the reservoir were produced at some marginal rate throughout its entire life. The method of calculation involved the application of fluid flow - material balance analysis to a series of successive steady state conditions in the reservoir. In the case studied very little difference in recovery was obtained at the abandonment pressure. An analysis of the basic factors involved indicates that the sane results would hold for considerable variation in properties of reservoir fluids, permeability of the formation or well spacing. Even if the reservoir has a water drive it appears that no harm will be done by- open flow production if the rate is cut back before any appreciable free gas is produced. However, any condition which leads to disproportionate withdrawal rates and which causes large pressure differences over large areas might result in substantial loss in ultimate recovery. INTRODUCTION When the pressure declines in a reservoir, gas is evolved from solution causing a shrinkage in the reservoir oil so that a stock tank barrel of oil with its residual dissolved gas occupies a smaller volume than originally. For a given reservoir oil saturation, therefore. stock tank oil content will be higher at the lower pressure. At the same time the evolved gas which remains in the reservoir reduces the reservoir oil saturation, and this would be expected perhaps to cause a reduction in stock tank oil content. However, around the well the shrinkage occurs so rapidly that stock tank oil may actually accumulate in this region in spite of the simultaneous reduction in reservoir oil saturation. If this accumulation should continue, spreading into a larger zone, the loss might be appreciable and because larger pressure gradients accompany higher rates the accumulation might possibly be large if wells are produced at too high a rate. It is the purpose of this paper to determine the effect of rate of flow on ultimate recovery by solution gas drive. The problem under consideration involves the unsteady state flow of oil in a closed radial system from which oil is produced by the evolution of gas as a finite drawdown is estalllished and the reservoir pressure declines. A somewhat similar unsteady state production problem dealing, however, with a linear system has been considered by Muskat and Meres, but these authors do not discuss the effects which rate may have on recovery. Other methods have been reported for estimaling recovery as a function of pressure decline when producing at an infinitesimal rate, and Muskat and Taylor' have shown the effect of fluid and reservoir characteristics on recovery under these conditions. Assuming steady state to exist, Babson has given a procedure for computing the decline in well productivity as the field is depleted, and Moyer has combined these methods to estimate abandonment conditions and the resulting ultimate recovery. These latter approaches to the problem either do not consider the effect of rate or assume steady state can be established. In detail this paper presents the behavior of the reservoir producing under unsteady state conditions and considers the effect of production rate during this unsteady state flow on the recovery attained. The analysis also shows that there will exist at abandonment a type of steady state, and on this basis a method has been clevelopetl for rapid calculation of abandonment conditions.

Jan 1, 1949

By T&apos Ke, ing-sui

NUMEROUS investigators have observed that internal friction accompanies cold-working of metals and the effect of annealing is to reduce this internal friction.1,2 However, - most of the experiments were made at high stress amplitudes and the principal purpose was to study the increase of internal friction as a result of the applied cyclic stress during measurement. In order to study the internal friction introduced by cold-working applied prior to the measurement, the stress level applied during the measurement of internal friction must be sufficiently small. The results of measurement are significant and can be used for a base of comparison only when the applied cyclic stress is so small that the internal friction is independent of stress amplitude. Internal friction of cold-worked metals under small stress level has been studied by a number of workers8 -" he internal friction was measured around room temperature with a frequency of vibration of the order of kilocycles per second. The purpose of this paper is to report a study of the change of internal friction when severely cold-worked aluminum was annealed at successively higher temperatures until it was completely recrys-tallized. The measurements of internal friction were made over a range of temperature extending from room temperature up to the temperature of prior anneal. The frequency of vibrations used was about one cycle per second. The apparatus used for the internal friction measurements to be reported in this paper was a torsion pendulum with the specimen in wire form as the suspension fiber. The description of this apparatus and the method of measurement have been previously given.7,8 The applied stress was sufficiently small SO that the magnitude of internal friction is independent of stress level at each temperature range concerned. Corresponding to this stress the maximum shearing strain on the surface of the specimen is of the order of l0-5 and lower. The in- ternal friction (Q-1) is reported as 1/p times the logarithmic decrement. Internal Friction Versus Temperature of Anneal: Fig. 1 shows the internal friction measurements performed upon 99.991 pct aluminum subjected to 95 pct reduction in area. The final diameter of the wire is 0.033 in. This figure gives a general survey of the effect of temperature of anneal and of temperature of measurement. The internal friction of the cold-worked specimen was first measured at room temperature. It was then annealed at 50°C for one hour and the internal friction measured at 50°C and at room temperature. The same wire was successively annealed at higher temperatures for one hour and measurements were taken at the annealing temperatures and lower temperatures as before. Such a procedure was followed in order to stabilize the internal friction at the temperature of measurement so that during the measurement which generally takes about half a minute, there is no detectable change in internal friction. This series of measurements .was made up to 450°C. After each annealing a short test piece of the specimen, which had received the same past thermal and mechanical treatments, was taken out for metallographic examination. It is seen from fig. 1 that up to the annealing temperature of 250°C we have the following observations: for any given temperature of measurement, the internal friction is lower the higher the temperature of prior anneal. When the annealing temperature is 290°C or higher, the internal friction at the annealing temperature drops abruptly to a value which is much smaller than that for the previous curve. Metallographic examinations showed that the recrystallization of the specimen was completed after the annealing at 290°C. Fig. 1 shows that, as far as internal friction is concerned, there is no abrupt transition between the processes of recovery and recrystallization. Averbach has also reached the conclusion that recovery may be a process analogous to recrystallization on the basis of X ray extinction measurements in brass." The effect of annealing temperature upon the internal friction at room temperature is shown by curve I of fig. 2. In this figure the internal friction at room temperature was plotted as a function of annealing temperature. It is seen that the internal friction decreases rapidly at first with an increase

Jan 1, 1951

By A. E. Bibb, J. R. Fascia

Single-crystal wafers of zirconium have been exposed to 680°F neutral water. The single crystals were of known orientation and weight-gain data as a function of crystal orientation were obtained. These data show that all the crystal faces studied obeyed a cubic rate law out to the time of transition whereupon the crystals corroded at an approximately linear rate. The time to transition varied from 114 days for (1074) crystals to about 325 days for the (2130) faces. The epitaxial relationship be-tween metal and monoclinic oxide was found to be (0001) H (111) and [1120] 11 [101]. A black tight adherent oxide layer was formed on the crystals in the pretransition range. This black oxide was found to be monocrystalline. The white corrosion product produced after transition was found to be polycrys-talline but highly oriented. X-ray line-broadening studies found that the black oxide was a highly strained structure whereas the white oxide was relatively strain-free. These results indicate a strain-induced re crystallization or fragmentation accompanies the change from protective black oxide to nonprotective white oxide. ZIRCONIUM alloys have been used quite extensively in high-temperature aqueous environments. Alloy additions can be made to commercial sponge zirconium which enhance the corrosion resistance of the zirconium in both water and steam media, which raise the tolerance limit for certain impurities detrimental to corrosion resistance, and which reduce the amount of free hydrogen pickup during corrosion. The development of the corrosion-resistant zirconium alloys has been a long and tedious job involving trial and error methods. This technique has been necessary because of a lack of fundamental data and hence understanding of the corrosion mechanisms. The objective of the work described herein was to provide some fundamental data with respect to the aqueous corrosion of zirconium crystals as a function of the orientation of the exposed surfaces. Hg. The zirconium chunk was then cooled to below the transformation temperature (862°C) and reheated to 1200°C for 8 hr. The ultimate size of the zirconium grains increased with the number of cycles. Rapid or even furnace cooling through the transformation temperature produces a considerable amount of substructure which was intolerable in corrosion experiments as it would be in the study of any crystallographically dependent property. It was found that a high-temperature a-phase anneal for approximately 4 days reduced the substructure below the limits detectable by visual or X-ray means. Crystals so produced were carefully cut from the massive zirconium chunk and oriented by standard back-reflection Laue techniques. The crystals were then mounted in a goniometer head and, by using the three degrees of freedom available, slices on the order of 0.015 to 0.020 in. were cut parallel to any desired crystal plane. These slices were then carefully polished on both sides to produce smooth flat faces, pickled to remove about 0.002 in. per face, annealed for 1/2 hr at '750°C in a vacuum of approximately 10"5 mm Hg, flash pickled, and checked for orientation. The pickling solution was 45-45-10 vol pct HN0,-H20-HF and continuous agitation was provided to eliminate pitting of the slices. Any slice that was not within 2 deg of the desired orientation was discarded, and any evidence of substructure as indicated by the Laue spots was also grounds for discarding the sample. Thin slices were used for the corrosion tests because weight gain per area data could be obtained with only a minimum area exposed to the corrosive media that was not of the desired orientation. The thin single-crystal slices were of irregular shape and as a result the areas were determined by placing a crystal inside an inscribed square of known area, enlarging a picture of this assembly about X5, and tracing both the enlarged square and crystal with a planimeter. The zirconium used to produce these single crystals was crystal-bar grade, a typical analysis of which is given in Table I. An oxygen analysis on prepared crystals gave a concentration of 205 ppm. The hydrogen concentrations are believed to be less than 15 ppm due to the dynamic vacuum anneal given each crystal. Typical nitrogen values for zirconium treated in this manner are about 10 to 20 ppm. RESULTS AND DISCUSSION Single-crystal wafers have been exposed to de-oxygenated, deionized water in static autoclaves.

Jan 1, 1964

By B. E. Cornish

Most technical and statistical data published on pyrophyllite relating to production figures, uses, markets and sales, have in the past traditionally linked the mineral with talc and soapstone. This is due to several common superficial physical properties resulting in substitute uses and applications. However, these minerals are not similar in chemical composition and do not generally occur in a similar geological environment. Pyrophyllite now stands on its own in the marketplace-particularly in ceramic applications-due to the combination of excellent heat shock and creep resistance properties of the mineral. The increase in pyrophyllite use in the field of ceramics indicates the continuing realization of these marked unique properties. Several new fields of ceramic applications, previously the preserve of high-alumina materials, have been developed on the intrinsic properties of pyrophyllite. Pyrophyllite is an aluminum silicate with the molecular formula of AI2O34SiO2H2O. It would be more appropriate to group pyrophyllite with such materials as kyanite, diaspore, andalusite, and certain high-alumina clays in relation to its general applications (Stuckey, 1928). These materials all have good beat shock resistance properties at high temperatures and are widely used for the manufacture of refractories. For those reasons they are interchangeable in some applications. Pyrophyllite also has many uses in nonceramic applications, the most important to date being as a substitute for talc in fillers. The major pyrophyllite mining operations are located in the US, Japan, Korea, Canada, and Australia, where the mineral is widely used as a raw material for general ceramic, mineral filler, and dilutant applications. Commercial Applications Pyrophyllite was first used in the last century for lining stoves and fireplaces, and also in the carving and polishing of ornamental objects. The rise in industrial demand for new products and applications resulted in the introduction of pyrophyllite as an alternative, mainly for talc and soapstone. Industrial filler applications followed for paint, paper, cosmetics, rubber, pesticides, crayons and pencils, and bleaching soap. The first use of pyrophyllite in ceramic applications was prior to World War II, in the manufacture of ceramic cladding tiles in the US. This was followed by the production of kiln furniture refractories and whiteware when pyrophyllite was offered by suppliers in North Carolina as an alternative to some local clays. The largest tonnages of pyrophyllite used today are in refractory linings in steel ladles in Japan, as seen in Table 1. The consumption of pyrophyllite in Japan is second only to clay and chamotte among refractory raw materials used. Recently this technology has been adopted in Australia. Japanese and Australian practice has resulted in appreciable technical and economic benefits, particularly when pyrophyllite is used in combination with zircon. The potential growth for this application is substantial if US and European steelmakers follow. Investigation and research into the properties of pyrophyllite determined the following main advantages of pyrophyllite-based ceramics: high corrosion resistance for molten iron, steel, and slags; good heat shock resistance; good indices of deformation under load and hot creep resistance (refractories); and increase in mechanical strength of whiteware products promoted by a better distribution of mullite in finished products (also obtained at lower firing temperatures than normally required in production of triaxial ceramics). White cement

Jan 1, 1983

By R. C. Buehl, M. B. Royer

High manganese slags of low phosphorus and iron content are produced by air oxidation of high phosphorus spiegeleisen in a basic-lined converter. Control of phosphorus and iron within specification limits for ferromanganese ore feed is obtained by a unique cyclic operating procedure. Various types of slags, or synthetic manganese ore, can be made. AN affiliated paper' describes the production of high phosphorus spiegeleisen containing 14 to 23 pct Mn and up to 4 pct P in an experimental blast furnace from open-hearth slag or manganiferous iron ore. This phosphorus content is too high for use of the spiegel in normal steel-production operations. Consequently, a preferential separation must be effected whereby the manganese is concentrated in a product that is usable in industrial operations. The preferential separation methods being investigated for this phase of the work are confined to pyrometal-lurgical processes for ready incorporation into steel-plant operations. It is fortunate that manganese is more actively oxidizable than iron or phosphorus, and therein lies a preferential separation method for isolating manganese from these two elements. Silicon is more strongly oxidizable than manganese, and its oxidation precedes, or occurs simultaneously, with manganese. Therefore, manganese and silicon are separable into a high manganese oxide slag phase while the phosphorus and iron remain in the molten metallic state. Complete separation of these elements represents an ideal condition which is not generally attainable in actual operations. This pyro-metallurgical method for separating manganese from phosphorus and iron by preferential oxidation was investigated by blowing 500 lb of metal in a basic-lined vessel to obtain preliminary information on the effectiveness of the procedure. Certain conditions of attainment in the separation process are desirable in any method for removing manganese from high phosphorus spiegeleisen, such as: 1—High recovery of manganese in the oxidation product; 2—the product to be of equal or better quality than ferromanganese-grade ore—48 pct Mn minimum, less than 10 pct SiO2, and Mn-P ratio of 300:1; and 3—attainment of the enumerated objectives in a product amenable to industrial handling, such as a slag of high manganese content that will flow from the processing vessel and of sufficient fluidity for ready separation of metallic granules that may have become mixed with the manganese slag phase. Previous Work Recovery of manganese from low grade ores and industrial byproduct slags by smelting to spiegeleisen, with subsequent oxidation to synthetic ferro-manganese-feed ores, has been a subject for periodic investigation during the past four or five decades in the United States and Germany. Joseph' and associates of the Bureau of Mines North Central Experiment Station, Minneapolis, Minn., smelted manganiferous iron ores of the Cuyuna range, Minn., to spiegeleisen and subsequently tried air and ore oxidation procedures for concentrating the manganese into synthetic ferrograde manganese ore. Joseph's results on the operation of a side-blown basic-lined converter for air oxidation of manganese from molten spiegeleisen were so discouraging that the procedure was abandoned after 11 blowing tests. Much slag was thrown from the converter vessel; phosphorus content was four to five times the maximum allowable for ferro ore; and a manganese-iron ratio of only 2 or 3:1 was obtained in the slag instead of the required 8:1. Oxidation of manganese from spiegeleisen with about 0.5 pct P, by adding iron ore to molten spiegel in an experimental open-hearth furnace, proved moderately successful in Joseph's experiments. The main drawback to the operation was the necessity for over-oreing for effective oxidation of the manganese with consequent too high iron oxide residual in the slag. Furthermore, the phosphorus content was proportional to the iron concentration and therefore much too high, so that several hours of reduction by a carbonaceous material were required to adjust the iron and phosphorus to the desired content of high grade ferro feed. A troublesome feature of the slag product of the spiegel oxidation process was its lack of fluidity if the silica content was less than 10 pct, the concentration considered desirable for the synthetic ore. Approximately twice the desired concentration of silica was required to impart enough fluidity for transfer from the vessel by pouring. The acute shortage of manganese in Germany

Jan 1, 1953

By C. C. Miller, W. F. Kieschnick, E. R. Brownscombe

The possibility has been mentioned that large pressure gradients in a solution gas driven field caused by high production rates might lead to a reduction in the ultimate recovery obtainable compared to that which would be obtained by a very slow rate of production. In the present study the reservoir conditions accompanying a high rate of production and the corresponding ultimate recovery were compared with those obtained if the reservoir were produced at some marginal rate throughout its entire life. The method of calculation involved the application of fluid flow - material balance analysis to a series of successive steady state conditions in the reservoir. In the case studied very little difference in recovery was obtained at the abandonment pressure. An analysis of the basic factors involved indicates that the sane results would hold for considerable variation in properties of reservoir fluids, permeability of the formation or well spacing. Even if the reservoir has a water drive it appears that no harm will be done by- open flow production if the rate is cut back before any appreciable free gas is produced. However, any condition which leads to disproportionate withdrawal rates and which causes large pressure differences over large areas might result in substantial loss in ultimate recovery. INTRODUCTION When the pressure declines in a reservoir, gas is evolved from solution causing a shrinkage in the reservoir oil so that a stock tank barrel of oil with its residual dissolved gas occupies a smaller volume than originally. For a given reservoir oil saturation, therefore. stock tank oil content will be higher at the lower pressure. At the same time the evolved gas which remains in the reservoir reduces the reservoir oil saturation, and this would be expected perhaps to cause a reduction in stock tank oil content. However, around the well the shrinkage occurs so rapidly that stock tank oil may actually accumulate in this region in spite of the simultaneous reduction in reservoir oil saturation. If this accumulation should continue, spreading into a larger zone, the loss might be appreciable and because larger pressure gradients accompany higher rates the accumulation might possibly be large if wells are produced at too high a rate. It is the purpose of this paper to determine the effect of rate of flow on ultimate recovery by solution gas drive. The problem under consideration involves the unsteady state flow of oil in a closed radial system from which oil is produced by the evolution of gas as a finite drawdown is estalllished and the reservoir pressure declines. A somewhat similar unsteady state production problem dealing, however, with a linear system has been considered by Muskat and Meres, but these authors do not discuss the effects which rate may have on recovery. Other methods have been reported for estimaling recovery as a function of pressure decline when producing at an infinitesimal rate, and Muskat and Taylor' have shown the effect of fluid and reservoir characteristics on recovery under these conditions. Assuming steady state to exist, Babson has given a procedure for computing the decline in well productivity as the field is depleted, and Moyer has combined these methods to estimate abandonment conditions and the resulting ultimate recovery. These latter approaches to the problem either do not consider the effect of rate or assume steady state can be established. In detail this paper presents the behavior of the reservoir producing under unsteady state conditions and considers the effect of production rate during this unsteady state flow on the recovery attained. The analysis also shows that there will exist at abandonment a type of steady state, and on this basis a method has been clevelopetl for rapid calculation of abandonment conditions.

Jan 1, 1949

By Arthur B. Yates

DIAMOND drilling has advanced and expanded during the past few years. Along with this increase there has been a marked trend to rely more and more upon drilling for the outlining of ore for reserve purposes. This is especially true underground, where men have not been available for opening up ore by crosscuts, drifts and raises. During the recent heavy call upon known ore reserves, more drilling has been done for exploration and it has become expedient to drill longer lateral holes from underground and deeper holes both from surface and from exploration headings in the mines. Furthermore, these deeper holes have to be drilled closely enough to warrant calculation of "probable" if not "proven" ore, from the results obtained therefrom. Interpretation of diamond-drill results has become more precise and reliable with the growing knowledge and understanding of the geologic structures that control the geometry of ore distribution, and this has broadened the field of usefulness of the drill. All of this has created a necessity and a demand for more accurate control of the hole as to direction, a more precise and reliable method of surveying for position, and a need for better and more complete core recovery, as well as larger cores, to provide an adequate sample. At depth the control becomes more difficult and, at the same time, more important. CONTROL A close study of drilling in various parts of the world for a period of more than 20 years has brought to light one definite rule, practically invariable; namely, that diamond-drill holes tend to deviate into a position normal to any structure existing in the rocks, such as bedding, schistosity, gneissosity, or even parting or jointing-even if the hole is started at almost any angle other than parallel with the structure. It also appears that the better developed the structure is, the more quickly will the hole get into a position perpendicular to it. It has often been said that there is a tendency for holes to "drift" in the direction of rotation. This is obviously untrue, for in a vertical hole the measure of deviation would depend upon the azimuth chosen as zero, and there is an infinite number of choices. It has been proved, however, that in homogeneous rocks there is a tendency for the hole to corkscrew, and that the direction of the spiral is the same as the direction of rotation. This may account for the belief that holes drift in that direction. Some tests have been made using right-hand and left-hand rods, and these show that no matter what the direction of rotation the hole will swing into a position perpendicular to the structure. Methods of Control The foregoing empirical rule may be used as an indirect method of control. If the prevailing structure is known, it may be advantageous to start the hole as nearly normal to it as possible, for the nearer the direction of the hole is to this ideal, the straighter it will remain. This, of course, is not always practical and in some cases is impossible. Usually such a

Jan 1, 1946

By R. W. Snyder, H. J. Ramey

This paper presents the results of applying the Buckley-Leverett' displacement theory to petroleum reservoirs consisting of a finite number of layers. The layers are assumed to communicate only in the wellbores, and the reservoir may be represented as a linear system. Most previous investigations of this nature were limited by assumptions and by inconsistent calculation techniques. This study improves on previous work by applying the Buckley-Lev-erett displacement theory to a noncommunicating layered system where permeability, porosity, initial saturation, residual saturation and relative permeability vary from layer to layer in a logical and consistent manner. Gravity and capillary-pressure effects are neglected. A modification of the Higgins-Leighton calculation method was used in this study. Waterflood predictions were made with all properties varying, and then with only permeability varying using several inability ratios. These results were compared with the Stiles and Dykstra-Parsons predictions. It is shown that the latter methods generally give poor values for the breakthrough recovery and pessimistic predictions for the performance after breakthrough. Similar results were obtained for a gas-displacement case. lNTRODUCTION Field experience with immiscible displacement usually shows constant producing conditions until breakthrough of the displacing fluid. Then oil production continues at increasing displacing-to-displaced fluid ratios until the economic limit is reached. Three different ideal mechanisms are known that will produce this behavior: (1) relative permeability effects as described by Buckley-Leverett frontal advance theory,' (2) vertical stratification as considered by Stiles,2 Dykstra and Parsons5 and others and (3) different path lengths involved in areal (two-dimensional) flow between wells as described by Dyes et al.4 Without question, a combination of these factors modified by formation heterogeneity and other known and unknown factors actually does control the behavior of real systems. This paper presents results of an investigation of certain factors that should affect performance but which have received little attention to date. In 1944, Law5 demonstrated that porosity and perme- ability are often found to have normal and logarithmic-normal distributions, respectively. throughout cored intervals in natural formations. This led to the concept of the noncommunicating, multilayered reservoir model for immiscible displacement. This model assumes that the reservoir is composed of a number of layers that communicate only at the wellbores. Each layer is individually homogeneous, but may be different from every other layer. Stiles' presented one of the earliest applications of this model to waterflood performance. In addition, Stiles assumed that the initial saturations and relative permeabilities were the same for each layer, porosity was the same. displacement was piston-like, fluids were incompressible and injection into each layer was proportional to that layer's permeability capacity (permeability-thickness product). The last assumption would be true if the mobility ratio for the displacement were unity.21 Dykstra and Parsons" used the same model as Stiles, but rigorously included mobility ratios other than unity for piston-like displacement. Dykstra and Parsons used their general result to produce charts for log-normal permeability distributions between layers. Similarly, Muskat6 Pub1ished analytical solutions for linear and exponential permeability distributions. In 1959, Roberts' described a scheme for calculating water-drive performance for the noncommunicating, layered reservoir model which considered two-phase flow in the displaced region. Roberts used the same model and assumed that the injection rate into a layer was proportional to that layer's permeability capacity, but that flood front locations could be evaluated from the Dykstra-Parsons results. These assumptions are inconsistent, and a material balance cannot be maintained except for a mobility ratio of unity. At the same time, Kufus and Lynch8 coupled Buckley-Leverett displacement theory with the layered model to provide an improvement of the Dykstra-Parsons method that was consistent. In 1960, Higgins and Leighton9 resented a numerical method for calculating waterflood performance also considering two-phase flow in the displaced region. The result was used to investigate variation in absolute permeability and oil viscosity. An excellent, detailed history of using the noncomrnunicating, layered reservoir model was presented by Nielsen.'" The preceding techniques (and many related ones) were similar in that differences in initial saturations, residual saturations and relative permeabilities from layer to layer were neglected. It is well known that the irreducible water saturation is an important function of absolute permeability. Calhoun11 showed that the irreducible water saturation

By T. E. Schmieman, J. E. Miller, M. L. Rizzone

Both centrifugal and reciprocating-type pumps have been widely used in the transport of slurries. Although with some limitations, centrifugal pumps may be used, especially for short-haul systems, however, for the long pipelines the reciprocating pumps are better suited. A state-of-the-art review is presented in which a discussion of applications is made and some of the problems associated with meeting the proper design conditions for satisfactory service are discussed. Several developments underway give considerable promise of better pumps in the future, although the current level of development provides for an economical means to move slurries. The movement of liquids in pipelines necessarily occasions the use of pumps. The petroleum industry is familiar with the transport of solids through mud pumps and cementing and fracturing pumps where the movement of slurries is an everyday matter. In the drilling of an oil well, the circulating fluid utilized to remove drill cuttings is called drilling mud. This substance is usually a fairly sophisticated material designed to develop certain characteristics desirable in the drilling process. The cuttings are suspended in a moving column of this fluid and brought to the surface. The separation of the cuttings from the drilling fluids is accomplished by the use of shaker screens and settling pits; however, it is impractical to remove the cuttings completely and as a result they are pumped through the mud pumps back into the circulating stream. Over the years, mud pumps have been improved so that rather long life can be obtained from liquid end parts subject to the attritional effects of the abrasive-laden fluid. It is from this background that reciprocating-type slurry pumps have been developed. Centrifugal Pumps Centrifugal pumps have also been used to transport solids, where low heads are required, typically up to 200 ft or so, and for short hauls. The centrifugal pump is a hydrokinetic device wherein the increase in velocity of a fluid stream is converted to head, and to achieve high heads a large change in velocity is necessary. Abrasive laden fluids cause wear on impellers and casings as a result of erosion by the fluid and the suspended particles. Centrifugal pumps, therefore, can only be used where the internal velocity of flow is rela- tively low. The advantage of centrifugal pumps is their high capacity at relatively low capital cost and usually relatively small space requirement. One of the disadvantages of the centrifugal pump when used in slurry pipelining can be seen in its typical pressure-volume performance relationship, which tends to work against the application (see Fig. I). If an increase in pressure (head) is occasioned by flow restrictions in the pipeline, say by the dropping out of solids, a desirable characteristic of a slurry pump would be that it develop increased pressure to overcome the restriction. The centrifugal pump provides the increased pressure only at the expense of considerably reduced volume which then results in a lower flow velocity. With the reduced flow rate, adequate velocity to hold the material in suspension and keep it flowing in the line might not be achieved. If centrifugal pumps are considerd for the movement of solids in a long line, a series of pumps must be staged in order to provide the necessary motivating force. A large number of pumps in the line would be required, since each of the pumps could provide only a small pressure increment. An equal number of standby pumps

Jan 1, 1971

By D. D. Pollock, D. I. Finch

PREVIOUS work' on a four-component system (Cu-Mn-Ni-Fe) resulted in the development of consistent relationships between the chemical composition and the electrical properties of these manganin-type alloys. The present study was undertaken to develop alloys with temperature coefficients of resistivity and thermoelectric properties more desirable than those of the manganin type, and to determine whether the relationships which had been found for the Cu-Mn-Ni-Fe alloys could be extended to five-and six-component alloy systems. PREPARATION OF ALLOYS The five- and six-component alloys were made from OFHC copper rod, ARMCO iron, electrolytic nickel, manganese cathode chip, and special high-purity aluminum and indium. A Cu-Mg master was used for deoxidation. The compositions of these materials are given in Table I. The alloys were melted and cast as indicated previously,' except that no cover was used and the melts were teemed. EXPERIMENTAL PROCEDURE The finished wire size of 0.0808 in. diam was again selected for the reason that the test specimens would be self-supporting, thus eliminating any extraneous effects which might have been introduced by winding smaller diameter wire on spools or forms. The following tests were performed on the finished wires: A) Chemical Analyses—All of the components of these alloys were determined by premium gravimetric methods. The principle residual impurity contained in these alloys is 0.008 pct Mg (by weight), maximum. Tables II and 111 present the mean analyses computed from at least four determinations of each constituent. B) Electrical Characteristics—The test procedures forthe determination of the thermal emf vs copper, resistivity, and the resistance-temperature relationship are given in detail in Ref. 1. It was also shown that the resistance-temperature relationship is of the form Pt = P,n + At -B/2, [1] where P, is the resistance at t C expressed in percent of a given standard resistance, P, is this per- 0 centage at 0°C, and A and B are constants for a given, properly treated, composition. The results of the electrical tests are also given in Tables II and 111. INTERPRETATION OF DATA The modified Linde2 formula, known to be valid for dilute binary solid solutions, was applied to the complex Cu-Mn-Ni-Fe type alloys. This relationship is of the form where Ap is the increase in resistivity. Zb the valence of the solute, Zn the valence of the solvent, and K and K are designations assigned by Robinson and Dorn3 to the constants for the periodic group to which solute element belongs. The units of K, are -cm per valence difference squared per at. pct; those of K2 are pa-cm per at. pct. For the sake of brevity, these units are not repeated in the following discussion. Calculations were made to determine if this formula was accurate for five-component systems. No experimental studies were made of the Cu-In and Cu-A1 binary systems. The effects of indium additions upon the resistivity of copper are given by Linde. These data, along with those of the effects of Mn and Fe, permitted the calculation of the effects of Al.

Jan 1, 1959

By J. M. Uys, T. B. King

The solubility of water in silicate melts of various compositions was measured. The basicity of the silicate did not appreciably affect the water solu-bulity at low-base content (acid compositions). Near the orthosilicate composition the solubility increased with basicity for silicates in which the cation displayed a weak ion-oxygen attraction and apparently decreased for those in which the cation showed a strong ion-oxygen attraction; metasilicates of the former class dissolved more water than those of the latter. Temperature had little effect on water solubility. The experimental results are interpreted on the basis of two modes of solution, the contribution of one decreasing, and that of the other increas -ing, with increased melt basicity. In the former, solution occurs through interaction with doubly-bonded oxygen atoms and in the latter, through interaction with singly-bonded oxygen atoms, or, in very basic melts, through reaction with free oxygen ions. THE hydrogen content of a steel melt is in a large measure determined by water dissolved in the slag. In some glasses water may be a major cause of "seeds". Water vapor in the furnace atmosphere is the primary source in both instances. A knowledge of the mechanism of water solution in silicate melts should help in assessment of practical methods for its control in steelmaking and glass refining. Walsh et a1.l measured the water content, expressed as hydrogen, of 40 pct lime-20 pct alumina-40 pct silica and 62 pct manganese oxide-38 pct silica melts as a function of the steam partial pressure, in equilibrium with the melt. Tomlinson 2 and, also, Russell3 investigated this relationship for a molten 30 pct soda-70 pct silica glass. In all three investigations, the solubility of water was found to be proportional to the square root of the partial pressure of steam. Moulson and Roberts 4 confirmed this relationship for a silica glass. On the basis of the square root relationship, Tomlinson2 and Russell3 interpreted the solution reaction as "network-breaking", similar to that expected on the addition of metal oxides to silica. Walsh et al.' postulated two possible modes of solution, one the mechanism suggested by Tomlinson and Russell and the other the reaction of the water molecule with an oxygen ion to form hydroxyl ions. These two modes of solution suggest opposite effects of melt basicity on water solubility. However, little appears to be known about the effect of melt basicity on water solubility. Walsh et a1.l found, in the lime-silica system, that the water content increased slightly with increased basicity. As these authors pointed out, this does not appear to be in accord with their further observation that slags containing little or no silica dissolve very little water. Kurkjian and Russell5 measured the effect of basicity on water solubility in alkali silicates in the composition range 15 to 45 mole pct alkali oxide. They found a minimum in the water content at about 25 mole pct alkali. This was interpreted on the basis of two concurrent solution reacZions; one in which solubility was proportional to the activity of doubly-bonded oxygen and, in the other, proportional to the activity of singly-bonded oxygen. The present work was aimed at establishing the effect of basicity on water solubility in silicate melts over as wide a range of compositions as practical. APPARATUS AND EXPERIMENTAL PROCEDURE The silicate melt was equilibrated with a "carrier-gas" of accurately known water content, quenched, and analyzed for water by a vacuum fusion technique. Some pertinent details of the equilibration procedure, analysis technique, preparation, and handling of the silicates are given below. Gas-Silicate Equilibration. The apparatus used to equilibrate the melt with the gas mixture was similar to that used by Walsh et al.' but with some important modifications.6 Purification trains were provided for nitrogen and hydrogen; whenever air or oxygen was used as carrier gas the nitrogen purifiCation train was used with the copper furnace at room temperature. Gas flow rates were measured with capillary flow meters; bleeders filled with a mixture of dibromo and tribromo ethyl benzene (density about 2 g per cc) were used for convenience in controlling flow rates.

Jan 1, 1963

By Glenn S. Wyman

CHUQUICAMATA, located in northern Chile in the Province of Antofagasta, is on the western slope of the Andes at an elevation of 9500 ft. Because of its position on the eastern edge of the Atacama Desert, the climate is extremely arid with practically no precipitation, either rain or snow. All primary blasting in the open-pit mine at Chuquicamata is done by the churn drill, blasthole method. Since 1915; when the first tonnages of importance were removed from the open pit, there have been many changes in the blasting practice, but no clear-cut rules of method and procedure have been devised for application to the mine as a whole. One general fact stands out: both the ore and waste rock at Chuquicamata are difficult to break satisfactorily for the most efficient operation of power shovels. Numerous experiments have been made in an effort to improve the breakage and thereby increase the shovel efficiency. Holes of different diameter have been drilled, the length of toe and spacing of holes have been varied, and several types of explosives have been used. Early blasting was done by the tunnel method. The banks were high, generally 30 m, requiring the use of large charges of black powder, detonated by electric blasting caps: Large tonnages were broken at comparatively low cost, but the method left such a large proportion of oversize material for secondary blasting that satisfactory shovel operation was practically impossible: Railroad-type steam and electric shovels then in service proved unequal to the task of efficiently handling the large proportion of oversize material produced. The clean-up of high banks proved to be dangerous and expensive as large quantities of explosive were consumed in dressing these banks, and from time to time the shovels were damaged by rock slides. As early as 1923 the high benches were divided, and a standard height of 12 m was selected for the development of new benches. The recently acquired Bucyrus-Erie 550-B shovel, with its greater radius of operation compared to the Bucyrus-Erie 320-B formerly used for bench development, allowed the bench height to be increased to 16 m. Churn drill, blasthole shooting proved to be successful, and tunnel blasts were limited to certain locations where development existed or natural ground conditions made the method more attractive than the use of churn-drill holes. Liquid oxygen explosive and black powder were used along with dynamite of various grades in blasthole loading up to early 1937. Liquid oxygen and black powder were discontinued because they were more difficult to handle due to their sensitivity to fire or sparks in the extremely dry climate. At present ammonium nitrate dynamite is favored because of its superior handling qualities and its adaptability to the dry condition found in 90 pct of the mine. In wet holes, which are found only in the lowest bench of the pit and account for the remaining 10 pct of the ground to be broken, Nitramon in 8x24-in. cans, or ammonium nitrate dynamite packed in 8x24-in. paper cartridges, is being used. This latter explosive, which is protected by a special antiwetting agent that makes the cartridges resistant to water for about 24 hr, currently is considered the best available for the work and is preferred over Nitramon. Early churn drill hole shots detonated' by electric blasting caps, one in each hole, gave trouble because of misfires caused by the improper balance of resistance in the electrical circuits. Primarily, it was of vital importance to effect an absolute balance of resistance in these circuits, the undertaking and completion of which invariably caused delays in the shooting schedule. Misfires resulting from the improper balance of electrical circuits, or from any other cause, were extremely hazardous, since holes had to be unloaded or fired by the insertion of another detonator. The advent of cordeau, later followed by primacord, corrected this particular difficulty and therefore reduced the possibility of missed holes. After much experimentation, the blasting practice evolved into single row, multihole shots, with the holes spaced 4.5 to 5 m center to center in a row 7.5 to 8 m back from the toe. Such shots were fired from either end .by electric blasting caps attached to the main trunk lines of cordeau or primacord. The detonating speed of cordeau or primacord gave the practical effect of firing all holes instantaneously. Double row and multirow blasts, fired instantaneously with cordeau or primacord, proved to be unsatisfactory in the type of rock found at Chuquica-

Jan 1, 1952

By David B. Brooks

Identified potential resources of lead and zinc are lower, relative to reserves, than the same ratio for other metals, Either there is little material below present grades or, if it exists, there are no data on it. The author examines both these factors in detail, and also introduces a third possibility. In their 1961 monograph, The Future Supply of the Major Metals, Bruce Netschert and Hans Landsberg noted that identified potential resources (that is, known but submarginal resources) of lead and zinc were much lower relative to reserves (that is, known and supermarginal resources) than was the same ratio for other metals.' Put another way, it seemed that for such metals as iron, manganese, copper, and aluminum, slightly more favorable economic conditions or modest advances in technology would greatly increase reserves by permitting the exploitation of vast quantities of leaner or deeper or otherwise less valuable mineral deposits. But for lead and zinc, Netschert and Landsberg concluded that either: "(1) there is relatively little material below present cutoff grades; [or] (2) such material exists, but for some reason there are no data.'12 This situation, which they called "the lead-zinc anomaly'' has been subsequently discussed by other authors. The purpose of this paper is to carry the discussion further by examining the evidence in favor of (1) and (2) and by advancing a third alternative. There are at least two reasons for devoting time to the lead-zinc anomaly. First, while it is unlikely that we shall have to turn to alternative lead or zinc resources in the near or middle-term future, the longer run resource picture for the two metals is not so certain.3 Both within the United States and for the world as a whole, new discoveries will have to come at a fair pace to keep up with growing rates of consumption. Thus, it is important to see whether there exist lower grade or nonconventional potential sources of two such useful metals that we could turn to at some time in the future. The second reason for studying the lead-zinc anomaly is also related to resource adequacy, but is of more general significance. Depending upon whether the anomaly is technologic, geochemical, spatial, or temporal in origin, we shall be able to draw some conclusions about the resource picture for other metals. Can we expect the apparent pattern of lead-zinc resources to be repeated? If so, will technologic advances in either exploration methods or mineral processing be able to alter the pattern? Or is the pattern unalterably set by geochemical distribution? Most important, are metals characterized by what seems to be an anomaly, different in any way from metals for which low-grade or nonconventional sources already have come to be exploited, as the porphyry deposits have for copper. In sum, investigation of the lead-zinc anomaly represents a case study combining both physical and economic aspects that may open up a neglected area in evaluating mineral resource adequacy. WHAT IS THE LEALLZINC ANOMALY? There are two dimensions to evaluations of the potential of any mineral resource? The first involves the degree of certainty that we ascribe to the estimate: how much do we know about the size of the resource as a result of geological mapping, exploration, and mine development? This dimension is expressed by the terms measured, indicated, and inferred reserves (and, if you wish, 'undiscovered reserves'), all of which terms carry with them the implication of exploitability under current cost-price conditions. The other dimension to evaluations of a mineral resource involves the economic limits of the estimate: how will the size of the resource vary with different (usually more favorable) cost-price conditions? (This economic dimension should be understood broadly to include all factors bearing on the cost-price relationship. In this sense it subsumes technology because any resource is exploitable at some cost; the role of technology is to bring cost down.) The latter dimension is expressed in the terms potential or sub-marginal 'ore,' and is logically quite independent of the former. For example, we have relatively good measurements of the tonnage of manganese in low-grade deposits in this country, though they are too lean to be considered reserves; on the other hand, we are much less certain of our measurements of new lead and zinc deposits in Missouri, though there is no question but that there is a sizable reserve. Thus, it may be uncommon but is not a contradiction to talk of measured submarginal ore or inferred potential ore.

Jan 1, 1968

By D. R. Uhlmann, T. P. Seward, O. Chalmers

A magnetic field has been used to damp out liquid convection during the solidification of castings. Ingots of Al-2 pct Cu were poured from various sperheats (10" to 65°C) into a room-temperature graphite mold located between the poles of an electromagnet. The effect on ingot structure of varying the strength and time of application of the magnetic field was investigated, and the results are interpreted in light 01- current theories of ingot structure. In the solidification of alloy systems, thermal gradients in the melt and differences in density of the constituents are expected to produce convective motion in the liquid. The thermal convection caused by temperature gradients should be present during the freezing of both alloys and pure materials, while the solute convection caused by density differences should be of concern only for alloys. The possible influence of this natural convection on the structure of castings has been discussed by Ruddle,' Chalmers, and Tiller. More recently, an experimental investigation of such effects was carried out by Cole and Bolling. These workers took stationary molds containing lead- and tin-based alloys and. using a brine solution. quenched them from various superheats above their respective liquidus temperatures. When grids were placed across the mold diameter to suppress convection, the grid region was later observed to contain a larger percentage of columnar grains than other parts of the casting or than similar castings poured without the grids present. From thermocouple measurements, they found the temperature in the grid region to be higher than that in the region outside the grids throughout the freezing process, and concluded that convection should be an important mode of heat transfer in normal castings. In addition to such convection arising from thermal gradients or differences in density of the constituents, a further source of convective motion, which we shall call "momentum convection", may be particularly important in small (laboratory-size) castings. By this term we refer to the convective motion produced in the initial pouring process, a motion which is damped out as the linear momentum and angular momentum of the liquid are dissipated. Besides these sources of convection, which are present to some extent in all castings. external influences may also be effective in producing convective motion. Examples of such "forced" convection which have been discussed in the literature include stirring the melt, shaking the mold, rotating the mold, and so forth The purpose of the present study was to examine the effect of convection on the structure of castings poured into a cold mold. In this work, a magnetic field was employed to damp out the convective motions within the liquid, and hence control the extent of con- The effect of a magnetic field on convective currents in a conducting liquid is to induce eddy currents which oppose and damp out the convective motion. vection. The technique of magnetic damping was previously used by Utech and F1emings" in their study of convective effects on impurity banding and other substructure in alloy crystals grown unidirectionally from the melt. In their investigation, fields as small as 200 gauss were found to be effective in damping the convection currents which influence the banding. I) EXPERIMENTAL TECHNIQUE In the present study, alloys of A1-2 wt pct Cu were poured into a room-temperature graphite mold. The mold, in the shape of a circular cylinder, 2 in. ID, 2-3/4 in. OD, 5 in. inside height, and 5-1/2 in. outside

Jan 1, 1967

By R. E. Zinkham, R. J. Goodwin

A mathematical study has been made of the amount of support a cement sheath could provide to casing cemented into the earth. Several assumptions were required to make the analysis, but only two of them are limiting: (I) the pipe must be completely surrounded with cement, and (2) any mud filter cake between the cement and formation has the same physical properties as either the cement or formation. The calculations showed that little support would be provided to the pipe before an unsupported cement sheath failed in tension; however, when the cement is confined between the pipe and wellbore and is loaded in compression, the pipe could receive a considerable amount of support. In fact, the theoretical results indicate the lower grades and larger sizes of pipe could have their working pressures doubled when reasonable compressive loads were applied to a surrounding cement sheath. These data are shown in six charts. Other down-hole conditions such as setting the cement under pressure, increased temperature and cement confinement all tend to increase the potential usefulness of the sheath. Because of size limitations, a laboratory program to verify the most important results of this mathematical study would be very difficult. However, small-scale field tests would be practicable. This paper shows that, if a solid cement sheath can be obtained in the field by either primary cementing or by repair after detection of flaws by surveys such as the new cement-bond logs, the use of this approach to reducing pipe costs merits further consideration. INTRODUCTION A modification in casing design practices is proposed which may either reduce the amount and grade of steel required to contain a specified internal pressure or permit the working pressure to be increased for a specified weight and grade of pipe. One of the more important considerations in casing design is its resistance to collapse; however, Bowers' and, more recently, O'Brien and Goins' have shown many casing programs are unnecessarily conservative in this respect, and they have indicated how savings can be made by designing for more realistic down-hole conditions. Earlier, Saye and Richardson howed that pipe costs could be reduced by considering the cement sheath as a part of the casing string when collapse resistance was being calculated. More recently, Rogers4 has raised the question as to whether a cement sheath might be considered in the design for burst resistance of the cemented casing. Calculations have been made for the increased burst resistance a cement sheath would provide for casing in a wellbore, and the results show that a sizable amount of support could be obtained in some instances. These data are presented in addition to a discussion of several other factors that are considered to affect the burst strength of pipe supported by cement. Two types of support are treated: Case I for tensile loading of the unconfined cement sheath, and Case for compressive loading of the confined cement sheath. ANALYTICAL TREATMENT AND RESULTS CASE I—TENSILE STRESSES IN AN UNCONFINED CEMENT SHEATH Conditions like this would most likely occur in a greatly enlarged portion of the hole where the cement was not in immediate contact with either the formation or a thin and hard mud cake. The mathematical analysis for this condition, as shown in the Appendix, rests on the following concepts. Pressure inside a unit length of pipe causes: (1) a tensile or tangential stress to be exerted over the longitudinal cross-sectional areas of the pipe and cement; and (2) an equal amount of strain in both the pipe and cement that is uniformly distributed over the wall thickness of each. This analysis was then used to make several calculations for a cement sheath around 51/2-in. OD pipe. The results are illustrated in Fig. 1, which shows that a tensile stress of 500 psi is imposed on a 5-in. thick sheath when the casing contains a pressure of only 1,450 psi. It also shows that a 10-in. thick sheath would be stressed to 500 psi in tension when the pipe contained a pressure of only 2,350 psi. Alternatively, if the stress analysis is made by means of the Lame thick-wall cylinder theory, the inner fibers of the 10-in. thick sheath will be stressed to 500 psi in tension when the pressure in the pipe is only 990 psi. This, of course, reveals that an unconfined sheath is of little support to the pipe in burst; however, an entirely different result is obtained when the cement is confined between the pipe and formation.

By R. I. Lahring, C. G. Inks

A surfactant waterflood, using a block copolymer of ethylene and propylene oxide (PLURONIC L64*), wa., started in 1956 in Kansas to determine the commercial feasibility of such a process. The production formation was the Bartlesville sand at a depth of 1,400 ft. Leares in the test area had attained both primary and secondary production peaks, and were on a normal decline when the tests were initiated. The injection wells were taking water at a reasonable pressure and none of the operating conditions were particularly unusual. The leases were selected primarily because of normal operating conditions, and not because of any serious problems demanding remedie>,. Oil production and water injection data were recorded during the 10-year test period, and their compilation indicates that the surfactant resulted in an increase of about 9 percent in secondary oil production. Other benefits derived from the surfactant injection were lower injection pressure that resulted in reduced power consumption and reduced erosion of the pumps; and lower calcium scale buildup. These fringe benefits more than offset the cost of the surfactant used. Introduction During the past several decades, considerable research has been carried out on secondary recovery of crude oil that remains in the producing formation despite the most efficient, current primary production practices. Methods are constantly sought of increasing recovery of oil, while at the same time improving the economic efficiency of operations. One method that has received intensive study over the years is the use of a surfactant as a waterflood additive. Laboratory tests show conclusively that dilute solutions of surfactants remove considerably more oil from uncon-solidated sand cores than does water alone.'- The loss of surfactant by adsorption at solid-liquid interfaces has caused serious doubt that surfactants can be used economically as waterflooding additives. This is especially true with anionic and cationic surfactants, and to a lesser extent with nonionic surfactants. This work was undertaken to determine the effectiveness in increasing oil production by injecting water containing small quantities of a nonionic surfactant. The surfactant selected was PLURONIC L64*, a block copolymer based on ethylene and propylene oxide, having the following structure The selection of the test site, a typical shoe-string sandstone type of field located at Batesville pool, Toronto District of Woodson County, Kans., was made because of its normal primary and secondary recovery operating conditions, and not because of any serious operating problems. When the tests were begun, the field was experiencing the customary post-peak production decline of a waterflood. Using for the tests a field that was on a normal production decline, while maintaining constant all variables other than the addition of the surfactant. was of varamount importance if success or failure was to be attributed to a particular cause. It was reasoned that if a surfactant was added to the injection waters and nothing else was done to influence the oil production or injection of water, the effects of the surfactant on the flood could be determined precisely. Production History The first well in the tested field was drilled in 1935. Gas repressurization began immediately, but it was not until Aug., 1938, that the major portion of the field was developed. During the period of repressurization, 1,700 MMcf of gas was injected. As can be seen from the curves of Fig. 1, the production peak from gas injection was attained in 1937 and a normal production decline followed. Early in 1942, water injection wells were drilled and injection of water Was initiated. The amount of water injected increased as more injection wells were drilled until a peak injection rate of 2,700 BID was reached in

Jan 1, 1969

By J. A. Coll, R. W. Cahn, A. Lawley

WHILE the creep properties of pure face-centered-cubic and close-packed-hexagonal metals have been thoroughly investigated and are well established, body-centered-cubic metals have been studied less extensively. Moreover, very few fundamental studies on the creep of solid solutions, irrespective of crystal structure, have been reported. The present study is concerned with the creep of a series of body-centered-cubic solid solutions. The present position concerning creep of pure metals is, briefly, as follows.1"3 Creep at first takes place at a steadily decreasing rate; this is the stage termed primary or transient creep. Except at the lowest temperatures this is succeeded by a stage of secondary or steady-state creep. At high temperatures and stresses, this may be succeeded by an accelerating stage, termed tertiary creep, with which we shall not here be concerned. There is no well-defined physical model at present for the transient stage; in general terms, transient creep is best regarded simply as a manifestation of work-harden ing. Steady-stage creep can certainly take place by several different mechanisms: the choice of dominant mechanism depends primarily on temperature. We shall here be concerned only with high-temperature steady-state creep, a term usually reserved for creep at absolute temperatures higher than 0.5 Tm, where T, is the melting point. In this range, the activation energy for creep is, for many metals, equal to the activation energy for self-diffusion, and this is generally interpreted in terms of a "climb mechanism.1-4 The creep rate is determined by the speed at which dislocations, impeded by obstacles the nature of which is disputed but which are probably established during transient creep, can climb by means of a diffusion process, until they are able to by-pass the obstacle. In solid solutions, the intrinsic resistance to the slip motion of dislocations may be much larger than in the solvent, to the extent that the motion of dislocations in the glide plane, rather than their escape by climb out of this plane, may become the rate-controlling factor. weertman5 has considered this possibility from a theoretical point of view, and concluded that some form of "viscous slip" is likely to be rate-controlling at comparatively low stresses. The resistance to slip may arise from "atmospheres" of impurities forming around dislocations; a high Peierls force in materials of high cohesion; or some structural peculiarity such as clustering or ordering of solute atoms.= We shall be concerned here with the case of ordering. The only published investigations concerned explicitly with the effect of order on creep refer to creep in ß-brass by Herman and Brown,7 and in Ni-Fe alloys, by Kornilov and panasyuk8 and by Suzuki and Yamamoto.9 Recently, Herman and Brown's paper has been supplemented by a determination of the tensile yield point of ß-brass as a function of temperature.10 Both studies showed a sharp drop in resistance to deformation of ß-brass over a range of a few degrees just above the critical temperature Tc at which order finally disappears. These observations are especially noteworthy, because in ß brass the degree of order diminishes steadzly to zero as the temperature approaches Tc. It is, therefore, the disappearance of the last traces of long-range order which has the largest effect on the resistance of the alloy to plastic deformation. In the Ni/Fe alloys of various compositions, resistance to creep at a given temperature and stress is maximum at the stoichiometric composition, both below Tc, (long-range order), and above T,. (short-range order).' Near Tc, the creep resistance of an ordered alloy is much higher than that of the same alloy in the disordered condition.9 The aim of the present investigation was to study the creep behavior in the neighborhood of Tc, of another system of ordering alloys. The iron-aluminum alloys were considered the most suitable. because: i) The order again diminishes steadily to zero as the temperature approaches Tc; there is no sudden drop in order at Tc, and it therefore is

Jan 1, 1961

By W. C. Hellyer, R. A. Campbell

In single-stage autogenous grinding, the buildup of a critical size fraction in the media can be corrected by removing this material through pebble ports, crushing it below the critical size range, and recycling the crusher product back to the mill. The rate at which the critical sire fraction is crushed affects the size distribution of the grinding media and this in turn affects the sire distribution of the grate discharge. This provides a means for controlling the grind produced by a single-stage autogenous grinding unit. The pilot-plant investigations on a very hard copper ore were carried out at the facilities of the Institute of Mineral Research, Michigan Technological University. In an autogenous grinding circuit in which feed at approximately 9 in. top size is reduced to a size suitable for subsequent processing, the build-up of a "critical size" fraction in the media causes problems. A "critical size" fraction has been defined as, "media too small to effect reduction by impact grinding of ore coarser than a quarter of an inch and too large to be broken by the largest size of media in the charge."' The buildup of a critical size fraction reduces the capacity of the mill, increases the grinding power requirements per ton of finished product, and generally produces a finer grind than is desired. It is general practice to overcome this problem by the addition of large-diameter steel balls to the grinding charge. This has certain disadvantages, such as 1) an increase in mill liner wear, 2) wear on the steel balls, and 3) some loss in flexibility in grinding circuit opera-tions resulting from difficulties in removing the steel balls by means other than by grinding out. A number of investigators' have suggested the use of a small crusher as an alternative to the use of large steel balls for control of a critical size fraction. With this technique the critical size fraction is removed from the mill continuously through suitable-sized pebble ports, crushed below the critical size range, and returned to the mill. An external crusher would cause no increase in mill liner wear, the wear on the crusher would be less expensive than the wear on the steel balls, and the flexibility of the grinding circuit operations would be enhanced since the crusher can be cut into and out of the circuit at will. This paper describes an autogenous grinding pilot plant investigation on a very hard copper ore, which led to the selection of an autogenous grinding flowsheet incorporating a crusher in the circuit as the preferred method for grinding this ore. Further development of the technique demonstrated that the crusher could be employed to control the product produced by an autogenous grinding unit. Description of Pilot Plant These investigations were carried out at the pilot-plant facilities of the Institute of Mineral Research, Michigan Technological University, Houghton, Mich. The autogenous grinding unit was a 6-ft-diam by 2-ft-long Hardinge Cascade mill with %-in. slotted steel grates. Pebble ports cut into the grates allowed passage of pebbles having a top size of approximately 21/2 in. The grate and pebble-port discharge material passed over a 3/16-in, trommel screen with the trommel under -size being pumped to the classification device. DSM screens were employed for classification in the early investigations, but were replaced later by a small Dorr rake classifier. The trommel oversize material returned to the mill via scissor conveyors. When the crusher was incorporated into the circuit, the trommel oversize material passed to a double-deck vibrating screen fitted with 2-in. and 3/4-in. square mesh screen cloths. The $ 2-in. and the —2 +3/4-in. size fractions were combined and crushed to a nominal 1 in. in a 4 x 6-in. jaw crusher. The crusher discharge and the —3/4-in. screen undersize returned to the mill. In the final investigation, a flap gate fitted to the top deck of the screen directed the — 21/2 +2-in. size fraction to the crusher or back to the grinding mill. The flap gate operated manually on a 15-min cycle, with this material being crushed for so many minutes out of each cycle. This was found to be a more reliable method of controlling the amount of — 21/2 +2-in. material crushed than attempting to make a split of a small weight of material on a continuous basis. Operational Techniques: Each sample was sized into three fractions and the Cascade mill feed was reconstituted from these size fractions in the proportions existing in the original sample. Sufficient feed for 15 min operation was weighed out and fed by hand over a 15-min period. The gross mill power draft was recorded every 15 min, corrected for tare power and drive efficiency, and reported as net kilowatt-hours per ton. A recording kilo-watt-hour meter provided a continuous visual record of the power drawn by the mill. Pulp densities of the trommel undersize and the classifier overflow (or DSM undersize) were taken every 15 min. The classifier overflow was sampled automatically. Timed samples of the classifier sands were taken every 15 or 30 min, weighed, and returned to the circuit. After correcting for moisture content, the weights were converted into percent circulating load. Timed samples of the +2 in., the —2 + 3/4-in., —3/4-in. screen fractions, and the crusher discharge, were

Jan 1, 1971

By C. M. Myrick

(Cleveland Meeting, October, 1912) THE following notes are submitted in the belief that they may interest some of the many owners of small water-power plants, so generally used in mining-work throughout the West. A small and somewhat primitive quartz-mill was taken over by a leasing company, and a 10-stamp battery was installed. Originally, power had been furnished by a Pelton wheel ; but, since the supply of water depended on the rate at which snow was melting on the mountains, a steam-plant had been added to help out during cold spells. This auxiliary plant was antiquated and expensive to operate, and, soon after starting up the remodeled mill, it broke down completely; so that it became necessary to get all the power possible out of the Pelton wheel,. with its ever-varying water-supply. The pipe-line, about a quarter of a mile long, was made up. of assorted sizes, from 7 to 11 in. in diameter; and, since it was buried deep under snow, there were no data from which to calculate the theoretical size of the nozzle. The stream being at this time at a low stage, it was important to make the most efficient use of the available water. This was done by using a nozzle large enough to pass the whole supply-taking care, however, to limit the size so as not to lower the water-level in the tank at the head of the pipe-line. As the weather became warmer, the nozzles were gradually enlarged to meet the increasing volume of water; but a point was finally reached where further enlargement only gave decreased power. Evidently the loss from friction had more than balanced the gain from the increased flow through the pipe. However, the area of nozzle that developed the, maximum power from the pipe-line had been found. This was used; and the surplus water was allowed to run to waste at the head of the line.

Oct 1, 1912