Search Documents

By M. A. Torcaso, P. Raimondi

To study mass transport in systems simulating oil recovery processes, different porous media were saturated with a mobile (carrier phase) and a stationary phase. Slugs of carrier phase containing a small amount of solute were displaced with pure carrier phase. By analogy to the chromato-graphic processes, the velocity of the solute can be predicted from a knowledge of the partition coefficient and the saturation provided that equilibrium between the two phases exists. Equilibrium was found to exist for different porous media, solutes and rates. The conditions were varied over the range normally encountered in the laboratory and in the field. The longitudinal dispersion of a solute undergoing interphase mass transfer was also investigated. INTRODUCTION The production of hydrocarbons by gas cycling, enriched gas drive and C02 or alcohol displacement involves, among other factors, relative motion between two phases and compounds, hereafter called solute, which are soluble in both phases. The solute is carried forward by the faster flowing phase at a lower velocity than the average velocity of that phase. Retardation of the solute is caused by chromatographic absorption and desorption in the slower flowing phase and by the degree of departure from equilibrium. At equilibrium the concentration of solute in the two phases can be related by the equation* CSw = K Cso ,............(1) where C, and C are the concentration of solute in the aqueous and oleic phases respectively and K is the equilibrium ratio, or partition coefficient. Displacement theories must contain an explicit assumption with regard to equilibrium, i.e., whether the compositions can be related by Eq. 1. The existance of equilibrium depends, in general, on the relative velocity between the phases. Unfortunately, other factors such as gravity segregation and viscous fingering, also depend on velocity. For this reason, whenever effects of rate on displacement were observed,2-4 it was practically impossible to discern what caused them — lack of equilibrium or the factors mentioned above. Equilibrium between phases has been the subject of extensive studies in fields such as extraction or chroma to graphy. It has received only small attention in flow through the type of porous media encountered in oil production.5 For this reason a method was developed which makes it possible to study the movement of a solute as it is affected by rate, type of porous media, partition coefficient and carrier phase, but in the absence of segregation or fingering. The information obtained enables one to determine when the assumption of equilibrium can be made. Briefly, the method consists of (1) saturating the core with a mobile and an immobile phase, (2) injecting a slug made up of the same fluid as the mobile phase and a small concentration of mutually soluble solute, (3) measuring the lag and the peak height of the slug at arrival and (4) correlating these variables with fluid properties such as partition coefficient and mixing constants of the medium. PROPOSED MECHANISM The principles of chromatography are combined with the equation of longitudinal mixing to predict the velocity of a solute slug compared to the bulk velocity and the peak height of a slug.6-9 The equation so obtained is valid under equilibrium conditions only. Therefore, a comparison between experimental and predicted results will give a measure of departure from equilibrium. This work was done with either the oleic or the aqueous phase being immobile. For simplicity, the following development is based on the case where the oleic phase is immobile. However, the treatment is the same in either case.

Jan 1, 1966

By W. O. Philbrook, H. W. Hosking, N. B. Melcher

A simple and inexpensive mercury-tracer method has been develohed to study rates and Patterns of gas flow in blast furnaces. A Pulse of mercury is injected into the hot blast, and its arrival at the sampling Point is recorded by an electronic circuit that measures resonant absorbtion of ultraviolet light by mercury vapor in the gas aspirated .through the detecting. cell. A rapidly developing interest in blast-furnace technology in recent years has created a strong demand for precise knowledge of the rates and patterns of gas movement through the stock column. Classical fluid-flow theory cannot supply the desired information because the complexity of the blast-furnace situation precludes the accurate determination of many of the parameters required for solution of the equations. In fact some of the terms employed in fluid-flow treatments become almost meaningless under blast-furnace conditions. The void fraction of the stock column, for example, varies widely from place to place and is affected by the segregation of charge materials, attrition of lumps during descent, and channeling. Gas density varies with changes in local pressure, temperature, and composition, while viscosity varies with temperature and composition. Even if mean values for these functions were acceptable, they would be either impossible or extremely difficult to determine with a high degree of accuracy since the value of the mean for all gas properties would depend upon the flow distribution itself. Attempts to study gas movement by the pitot-tube determination of kinetic pressures have met with little acceptance. Reproducibility of results is extremely difficult to achieve in a situation where alignment of the tube orifice with respect to the flow direction in tortuous channels cannot be guaranteed. Because of these difficulties it would appear that progress can be achieved only with a direct method of measuring gas velocities and determining the shape of flow paths through the stock. The establishment of such a method is described in this paper. SELECTION OF METHOD Direct measurement suggests the use of a tracer by means of which the progress of a "parcel" of gas can be followed through the furnace. Several requirements must be met before any selected material can be considered a suitable tracer. First of all, it must be a substance not normally present in blastfurnace gas or dust; otherwise its presence in a gas sample will have little significance. It should be volatile at temperatures normally existing within the furnace, to ensure that it will travel with the gas, as a gas. It should possess special properties enabling its presence in the gas to be detected readily, and it should not undergo exchange reactions with any material normally present within the furnace, including refractories and coke as well as all components of the metal and slag. Radioactive materials naturally are considered because their radioactivity renders them susceptible to detection. However, of the many radioactive materials available, almost all are eliminated from final consideration by their unsuitability in terms of other properties. Radioactive silicon, carbon, calcium, phosphorus, and many others have been considered and discarded, either because they are not volatile over the whole range of significant temperatures, or because they could be expected to undergo exchange reactions with burden or refractory materials. Others which might be suitable in terms of these properties are eliminated because of a low activity, short half life, or the necessity for fragile counting apparatus. Of the many elements available in radioactive form, perhaps radon is the only one suitable for blast-furnace gas-flow studies. This has been used in several investigations1-4 with considerable success. The use of radiotracers has certain inherent disadvantages. One is the cost. An appreciable sum must be allowed for materials each time a test is made. Also, special methods of handling must be employed, and very often the progress of an investigation must be governed by the availability of isotopes and the delivery arrangements that can be made for them. An advantage is immediately gained if the tracer material can be a substance which can

Jan 1, 1960

By M. I. Jacobson, A. S. Yue, A. E. Vidoz, F. W. Crossman

An equation governing the concept of constitutional supercooling under the combined effect of concentration and temperature gradients was used to produce platelike Al-CuAl2 eutectic composites for mechanical properties studies. Compression specimens were prepared from a single-colony Al-CuA12 eutectic composite ingot, 2 in. in diam and 12 in. long. The specirrzens were cut such that the platelets were oriented parallel, 45 deg, and perpendicular to the compression direction. Since the ingot was of eutectic composition, The aluminum-rich matrix could dissolve 5. 7 wt pct Cu in solid solution, and therefore could be strengthened by precipitation hardening. Specimens were tested at room temperature and elevated temperatures in the unidirectionally solidified, solution-treated, and solution-treated plus aged conditions. The results were compared with those for the conventionally cast and extruded specimens. For the controlled material, the highest strengths were obtained with platelets oriented parallel to the compression axis. In the unidirectionally solidified condition, 0.2 pct offset yield strength was 32,000 psi; however, this was increased to 59,000 psi by solution treatment, and further increased to 90,500 psi by solution treatment and aging. The attainment of high compressive strengths in the Al-CuAl2 eutectic composites was interpreted in terms of the buckling of elastic CuAl2 platelets in the plastically deformed a aluminum matrix. SINCE the discovery of high-strength whiskers,' scientists and engineers have made significant progress toward incorporating these whiskers into metallic matrices, forming composites for basic studies and structural application. The general procedure is to produce the whiskers first and then to bind them together with a ductile matrix. The production of whisker-reinforced composites requires tedious handling techniques,, particularly when it is desired to align the whiskers unidirectionally. Furthermore, the interfacial bond between the whisker and the matrix is frequently poor3 so that the resulting composite has strengths lower than expected. These disadvantages are generally true for any metallic composite produced by physically mixing the components. It is possible to eliminate these shortcomings by growing whiskers directly in the matrix material by eutectic solidification.4-8 In eutectic solidification, the matrix phase and a whisker phase are grown approximately simultaneously from a liquid of the same overall composition at the eutectic temperature. If the solidification process is controlled by varying the freezing rate, the temperature gradient, and the impurity content, platelike or filamentlike whiskers are produced parallel to the growth direction. The morphology of the grown-in reinforcement, i.e.. plates or rods, generally depends on the volume fraction9 of the dispersed phase present in the eutectic mixture. Since the unidirectional eutectic solidification is a one-step process, i.e., the liquid-solid transformation process, an excellent interfacial bond between the matrix and whisker is obtained. An additional advantage is that no special handling technique for whiskers is needed. In recent years, many investigators10-13 have studied the effects of growth variables on the micromorpholo-gies of binary eutectic alloys produced by controlled solidification. The study of their mechanical properties was initiated by Kraft and coworkers14-16 who found that the strength of cast A1-CuA12 eutectic alloy can be increased threefold by unidirectional solidification. In the A1-AL3Ni system, a strength of 50,000 lb per sq in, was reported for the unidirectionally solidified eutectic alloy, a value five times higher than for conventionally cast material. Thus, the unidirectionally solidified eutectics can be used as fiber-reinforced composite materials. In this paper, we shall first use an equation17 as a guide for the production of eutectic composites in general and the Al-33 wt pct Cu eutectic in particular. Experimental data supporting the theoretical prediction are given. Second, the compressive properties of the grown A1-33 wt pct Cu eutectic were thoroughly investigated in terms of platelet orientations, thermo-mechanical treatment, and temperature. The experimental data are interpreted in terms of a buckling model of fibers in elastic fiber-plastic matrix metallic composites. EXPERIMENTAL PROCEDURE Crystal Growth. The following experimental procedure was adopted for the production of controlled microstructures in the A1-33 wt pct Cu eutectic alloy. The controlled solidification was accomplished with a movable resistance-wound radiation furnace. Fig. 1 is a schematic drawing of the solidification apparatus. A water-cooled chiller was placed into a degassed high-purity graphite crucible containing the charge. Rubber stoppers wrapped with aluminum foil were used to seal both ends of the quartz tube through which a dried argon atmosphere was passed under a slight positive pressure. At both ends of the quartz tube, radiation shields were used to minimize heat loss. The quartz tube was held in place by two steel clamps and the furnace was drawn vertically by means of a steel cable against the steel truss which permits the furnace to move without touching the tube. The drive mechanism consisted of two pulleys, a counter weight.

Jan 1, 1969

By H. F. Silliman, Daniel R. Hull, John R. Freeman

IN the normal operation of a brass-rolling mill, sheet and strip has, for the most part, been finished in comparatively thin gauges, involving a substantial amount of coldwork and a considerable number of anneals. This condition has been disturbed by the prep0nderance of cartridge brass, which is not rolled to thin gauges, and particularly by brass for artillery cartridge cases, on which the mill may finish its work at a thickness between 0.400 and 0.900 in. Obviously, the amount of rolling and the number of anneals to which such a product can be subjected are small compared with strip that is carried to a thickness of a few hundredths of an inch. As a result, critical examination into the internal condition of metal has been made on an extensive scale at a stage of manufacture that would not, in normal times, have been chosen for complete inspection. Under these conditions, a type of defect has been recognized that is not seen at thinner gauges. It might be more accurate to call it the appearance of a defect, since it refers to an apparently laminated, discontinuous structure, which, in fact, does not exist as such, and disappears after suitable treatment. For this reason it has been called a phantom lamination, which the authors consider an appropriate term. It is the purpose of this paper to describe the phenomenon and the conditions of its occurrence and, at least tentatively, to discuss its nature and cause. Great numbers of phantoms may be found in 2: 1 brass, either hot-rolled or cold-rolled. They are also found in 70-30 brass, sometimes when hot-rolled and generally when cold-rolled. It is not believed that phantoms are confined to these alloys but this paper is limited to them for the purpose of description. HOT-ROLLED 2:I BRASS For illustration, therefore, a typical cake of hot-rolled 2: 1 brass has been chosen. This was rolled to a slab 7/8 in. thick, from a casting 5 in. thick by 24 in. wide by 18 in. high, which was believed to have been sound. After hot-rolling and cooling, the slab was sheared and a portion of such a shear cut is shown in Fig. 1. It would be difficult to convince anyone viewing this specimen that the metal was not unsound. The impression would be confirmed by the appearance of a tensile break, as shown in Fig. 2. This is an ordinary tensile-test piece from metal just described. Although there was nothing in its tensile strength or elongation that suggested unsoundness, it appeared run through with pipes and laminations. To question the reality of such a condition would imply questioning the obvious. But, considering the history of the metal, it w0uld be difficult to believe that it could be so bad as it appeared. It seemed reasonable, though, that if the defects were what they appeared to be, they could be traced back from the sheared or broken face.

Jan 1, 1945

By R. J. Tailleur, M. Rosenberg

Oil well drilling muds prepared with lubricating aids such as oil, graphite or mica will not produce a sufficiently strong protective lubricant film for the bit bearing surfaces under high load conditions encountered in drilling operations. Consequently, the damage to the bearing surfaces resulting from the absence of such a film frequently results in a shortening of the drill bit life. Several different types of extreme pressure lubricating additives for use in muds have been developed. These arlrlitives are capable of providing a protective lubricating film for bearing surfaces subjected to high load pressures. A modified version of the Timken lubricant tester, an instrument commonly used for testing the extreme pressure lubricating properties of oils, is used for measuring and controlling the lubricating qualities of the mud. Comparison tests made in the laboratory with 55/8-in. tricone bits drilling on steel plates immersed in extreme pressure lubricating muds and conventional muds showed that the bearing life of those bits tested in the lrrbricating mud was three to four times greater than obtained with conventional muds. Drilling tests made with extreme pressure lubricating muds in West Texas increased over-all bit life three to fourfold, reduced drilling torque and wear on drill pipe and drill collars. INTRODUCTION Roller bit cones contain roller, ball and journal-type bearings that are subjected to very heavy loading during drilling operations in which the only lubricant available for these bearings is either water or drilling mud. These bearings must be able to operate satisfac- torily in order for the cutting structures on the surface of the cones to be fully utilized. Frequently, the bearings wear to the point that the cones freeze and the bit must be pulled before the cutting structures on the cones become worn. In some instances the bearings continue to turn with severe wear but the cones, which are held on the bit by the bearings, drop off; and this causes an expensive fishing job. In other instances the bearings wear to the point that the cones pinch in causing an undergauge hole and delays to ream the hole. The advantage of increasing bit bearing life is self-evident. Because of inability to control the internal wear of bits while drilling, it was felt that improvement of the lubricating qualities of the circulating mud would be helpful. However, the often-discussed lubricating property attributed to muds has been a rather vague and intangible one. The literature has implied that the oil-emulsion muds are more effective lubricants than non-emulsion muds. Actually, there has been no direct method of measuring the lubricating property of muds which would indicate that one mud was better than another; there has been no way to determine whether the lubricating property of any mud was adequate. Furthermore, in comparing lubricating properties of muds, two qualities should be considered—the coefficient of friction and the extreme pressure lubricating qualities. For example, graphite can reduce the coefficient of friction, but does not provide a strong enough lubricating film to protect bit bearings subjected to high loads. The primary object of the investigation reported herein was to find a method for prolonging the bearing life of drill bits; and considering the heavy loads used in drilling, it was felt necessary to find both a method of measuring lubricating properties under high load conditions and methods of establishing effective lubrication under these conditions. Extreme pressure lubrication deals with that realm of lubrication where metal surfaces are in rubbing contact with each other under very high pressures. These pressures may be quite high, as for example,

By E. C. Reed

Drilling activity in Nebraska during 1945 continued to decline slightly over that of the previous year. Eight tests for oil and gas were completed during the year, of which seven were wildcats and resulted in dry holes. The eighth test, an inside location in the Dawson field of Richardson County, yielded an initial production of about 3o bbl. per day with 86 per cent water from the Hunton formation. Five wells were drilling at the end of the year, two of which were wildcats. Two of the drilling wells were deepening operations in the Dawson and Falls City fields and the third was an inside location in the Falls City field, which appears likely to result in a producer. Most of the operations were in Richardson County but two wells were drilled in Dawes and Gage Counties and one each was drilling in Holt and Washington Counties at the end of the year. There were no new discoveries of oil or gas.

Jan 1, 1946

By Walton J. Greer, System By John E. Owen

The guard electrode system measures the resistivity of formations by employing a thin disk of current which is caused to flow perpendicular to the bore hole. The control of this current disk is obtained in a brute force manner through the use of relatively long equipotential electrodes above and below the measuring electrode. The log obtained from the system is free of "lag," "plateau," "shadow," "reflection" and other distortions evident on conventional logs. The proportionate contributions of the hole size and invaded zone resistivity to the apparent resistivity reading are reduced when the mud and filtrate resistivities are lower. Thus, the guard system favors the use of conductive muds. The mathematical development of the theory is given in an appendix. Equations are derived to evaluate the effects of mud resistivity, hole size, invaded zone resistivity and depth, and the true formation resistivity. Sample logs from several provinces are reproduced and compared with conventional electric logs to illsutrate the much greater detailed lithology that can be presented by the guard electrode system. INTRODUCTION With increased ability of those in the petroleum industry to analyze formation characteristics from electrical resistivity data, there has become apparent the need for more precise measures of that parameter. The measurement of the resistivity of a homogeneous and isotropic material can be made simply when the body of the material is infinite in all dimensions and the measuring electrodes can be placed within the body. In such a case, the current leaving an electrode follows a spherical distribution and the mathematical expression for the potential level at any distance from that electrode can readily be derived.'.' If it is considered that the active electrodes are within a bore hole filled with mud of a resistivity different from that of the formation. the current does not flow in a spherical pattern near the current source or sink, and the calculations of potential levels become more difficult. The additional consideration of a section of formation invaded by mud filtrates, and thus having resistivity different from either that of the mud, the adjacent formations or of the undisturbed formation, makes the mathematical problem extremely complex. Should the vertical dimensions of the formations be considered as finite. the problem becomes so complex as to preclude reasonable solution. Yet, even these considerations have not described adequately the conditions encountered in a large proportion of the wells to be studied. In efforts to evaluate the effects of the various conditions. combinations of twn, three. and four electrode logging con- figurations of the conventional types have been used. The resulting logs have left much to be desired in some provinces. It has become apparent that the use of such configurations will not result in adequate measurements being made, particularly in cases where the formation is composed of thin sections. If all the current of a resistivity measuring circuit is made to flow through the formation opposite the exploring electrode, many of the shortcomings of the conventional measuring system are eliminated. In the guard electrode method of electrical well logging to be discussed in this paper, the current is so controlled by causing it to flow in a thin disk normal to the axis of the logging tool. EARLY HISTORY The guard electrode method of electrical well logging in its early years was a joint development by the Geophysical Research Corp. and the Amerada Petroleum Corp. The method was first experimentally investigated by means of model studies. The results of these studies indicated that current focusing systems properly applied to electrical well logging

Jan 1, 1951

By L. A. Panek

Research on roof bolting has developed significant information with respect to the functions that can be performed by properly installed bolts and the methods that can be used to ensure that effective installation has been achieved. The present paper brings together results that are pertinent to the design of a bolting system for reinforcing horizontally stratified mine roof with vertical bolts. The design approach is based on the use of bolts to decrease the maximum bending stress within an arbitrary sequence of roof strata (see Fig. 2) in which the only loads are the weights of the individual beds. The use of rock bolts to achieve other objectives, such as to stabilize a fractured rock mass on the periphery of a mine opening,3 is excluded from consideration herein. Reinforcing effect of bolts consists of a friction effect and a suspension effect in combination. "Friction effect" refers to reduction of bending in a stratified roof due to clamping action of tensioned bolts, which compress the strata, thereby creating frictional resistance to displacement along planes of stratification. (The flexure of a sequence of strata is necessarily accompanied by horizontal displacement of each bed with respect to its neighbor, along mutual surfaces of contact.) Although the sliding of the beds tends to exert a shearing effect on the bolts, tests show that this has negligible influence on the bending stresses, probably because the bolts are so far apart. "Suspension effect" refers to the transfer of part of the weight of the weaker or thinner strata to one or more thick strata, which occurs when strata with differing tendencies to deflect are constrained to have equal deflection. The term "suspension" is used irrespective of whether the thin strata are above or below the thick strata, because tests show that the supporting effect of the flexurally more rigid roof strata is for practical purposes independent of their position in a bolted sequence of strata. An earlier paper4 dealt with a bolted unit in which all strata had equal flexural rigidity; bolting could develop a friction effect but no suspension effect. The present paper deals primarily with a bolted unit in which all strata do not have equal flexural rigidity, so that bolting can develop both a friction effect and a suspension effect. The reinforcing effect of the bolts was determined by a combination of experimental and theoretical stress analysis.4'6'7 The experimental method consisted of loading a model by rotating it in a centrifuge to simulate the gravity forces exerted about an underground excavation. Models were made from two different limestones, although the results are independent of the material because the elastic constants were taken into account in the data analysis. Electric resistance strain gages were bonded to the highest and lowest members of the bolted unit to determine the outer-fiber bending strains at the center and at the supports. The quantitative results presented herein are based on tests of 56 different models, which included a range of values for the structural parameters. Each model was tested several times, with different combinations of spacing and tension of the bolts. DESIGN EQUATIONS The effects of friction and suspension on the flexure of a bolted stratified roof can be expressed by the following equations, which give the maximum bending stress, the deflection, the friction effect, the suspension effect and the transferred load for any (the i-th) member of the bolted unit in terms of the structural parameters:

Jan 1, 1964

By F. C. Blickensderfer

During 1914 and 1915, extensive experiments were conducted at the concentrator of The Detroit Copper Mining Co. of Arizona, at Morenci, Ariz., in order to test the relative grinding efficiencies of the Marathon, the Chilean and the Hardinge Mills. The Marathon mill used in the experiments was the first one ever built by the manufacturers; and since this was the first time that it was given a thorough tryout, with such remarkable results, the data have been assembled in the following paper and submitted in the interests of the milling profession. Description of the Flow Sheet The concentrator flow sheet, as it existed at the time of these tests, is shown in Fig. 1. The total mill feed, as delivered from the crushing plant, had as its maximum size 1-in. material. This material was screened dry on Cole Zig-Zag screens fitted with 4-mesh openings; the oversize going to one pair of coarse rolls, the undersize to five Wilfley tables fitted with Butchart National riffles. The coarse-roll product was elevated and screened wet on Zig-Zag screens fitted with 4-mesh openings, the undersize going to the five tables mentioned above and the oversize to one pair of fine rolls. The fine-roll product was elevated and screened together with the coarse-roll product; so that, before any concentrating operations took place, the total mill feed was reduced to pass a 4-mesh screen. After concentration on Butchart-riffled tables, the tailings from these tables passed to de-sliming hoppers, where two products were formed, viz., an overflow and a discharge. The discharge constituted the feed for the Chilean mills. It contained 16 per cent. slime (—200 mesh) and 3 parts of water to 1 of solids. The concentrator was equipped regularly with four Chilean mills (Monadnock type) to the unit; but, in order to

Jan 1, 1917

By Harvey T. Kennedy, Charles R. Olson

In many investigations of the performance of petroleum reservoirs the assumption is made that the liquid, if below its bubble-point pressure, is at all times in equilibrium with gas. On the other hand, observations by numerous investigators have indicated that gas-liquid systems including hydrocarbon systems, may exhibit supersaturation to the extent of many hundred psi in the laboratory. Up to the present, there has been no reliable data on which ti judge the actual extent of supersaturation under conditions approaching those existing in petroleum reservoirs. The work reported here deals with observations and measurements on mixtures of methane and kerosene in the presence of silica and calcite crystals. Bubbles were observed to form on crystal-hydrocarbon surfaces in preference to the glass-hydrocarbon interface or to the body of the liquid. Statistically, it was found that the number of bubbles formed per second per square centimeter of crystal surface was a function of the supersaturation only. and the function was evaluated graphically. Supersaturations were observed up to 770 psi, under which condition bubbles formed quickly and with considerable violence. With decreasing degrees of supersaturation, the frequency of bubble formation became less, until at 30 psi supersaturation and lower, no bubbles were observed to form, even though the observation at 30 psi was continued for 138 hours. It was found that silica and calcite crystals had identical effects, within experimental error, in accelerating the formation of bubbles, and that small amounts of water and crude oil had no effect on the results. It is shown that the maximum supersaturation that can exist in a reservoir may be calculated from the data presented and from the area of the rock surface. It is also shown that the number of bubbles formed in the reservoir, in order of magni- tude, may be calculated for any rate of pressure decline imposed on the reservoir by production. The bearing of the number and distribution of bubbles on reservoir performance is discussed. INTRODUCTION A liquid system is supersaturated with gas when the amount of gas dissolved exceeds that corresponding to equilibrium at the existing pressure and temperature. The degree of super-saturation may be conveniently expressed as the difference between the bubble-point of the mixture and the prevailing pressure. Thus, if a mixture having a bubble-point of 1,000 psi at a given temperature exists in single liquid phase at 700 psi at the same temperature. it is supersaturated to the extent of 300 psi. There are many examples of high supersaturations, mostly in aqueous solutions, reported in the literature. Thus, Kenrick, Wismer and Wyatt1 showed that water may be saturated with oxygen, nitrogen or carbon dioxide at 100 atmospheres, and the pressure reduced to one atmosphere without producing bubbles immediately. When liquids are in a state of tension, they may be considered as supersaturated at least to the extent of the tension. The tensile strength of water has been reported as 30 atmospheres by Meyer,1 60 atmospheres bv Budgett. 30 to 50 atmospheres by Temperley and Chambers,4,5 200 atmospheres by Dixon6. and 223 atmospheres by Briggs.7 Vincent8,9 determined the tensile strength of a mineral oil as 45 psi. Gardescu1 maintained pressures for short times in a model reservoir at 115 psi below the bubble-point. It should be noted that the high supersaturations observed were obtained on systems carefully purified to remove particles or surfaces which might promote the formation of bubble; These "nuclei" were considered as contaminants which interfered with the determination of a property of the liquid. In

Jan 1, 1952

By P. M. Blair, D. W. Peaceman

The shape and position of the gas-oil transition zone during downdip displacement of oil by gas has been calculated using flow equations which include the effects of gravity, relative permeability, capillary pressure and compressibility of the fluids. The calculations treat the problem in two space dimensions, and results are compared with data from a laboratory model tilted at 30° and 60° from the horizontal on displacements near and above the maximum rate at which gravity segregation prevents channeling of the gas along the top of the stratum. The good agreement between calculated and experimental results demonstrates the validity of the tecbnique as well as that of the flow equations. INTRODUCTION Knowledge of the fluid distribution and movement in an oil reservoir is important in producing operations and estimation of reserves. The history of the oil industry has included steady progress in improving the accuracy of calculations which provide the required knowledge. The earliest method of calculating reservoir performance consisted of material-balance equations based on the assumption that all properties were uniform throughout a reservoir.l For many reservoirs such a simple formulation is still the most useful. However, when large pressure and saturation gradients exist in a reservoir, the assumption of uniform values throughout may lead to significant error. To reduce these errors, Buckley and Leverett2 introduced a displacement eqation which considers pressure and saturation gradients. Methods available at that time permitted solutions to the Buckley-Leverett equation in one space dimension; these solutions have been very useful in solving many problems related to the production of oil. However, the one-dimensional methods are not adequate for systems in which saturations vary in directions other than the direction of flow. An example of such a system is the case of gas displacing oil down a dipping stratum in which the gas-oil contact becomes significantly tilted. Of course, the Buckley-Leverett displacement method cannot predict the tilt of the gas-oil contact. Recent improvements3,4 of the one-dimensional Buckley-Leverett method achieve some success in predicting the tilt of the gas-oil contact at sufficiently low flow rates. However, at rates high enough that the viscous pressye gradient nearly equals or exceeds the gravity gradient, even these improved one-dimen,sional methods incorrectly predict the shape and velocity of the contact. Further progress in estimating such fluid movements in a reservoir appears to require consideration of the problem in more than one space dimension. The recent two-dimensional method of Douglas, Peaceman and Rachford5 appears adaptable to calculate changes with time of the saturation distribution in a vertical cross-section of a reservoir. The movement of saturation contours should represent the moving fluid contacts and include the effects of crossflow due to gravity, as well as variations in the rock and fluid properties. The nonlinear nature of the equations used in the method has prevented proof of the validity of the solutions. Douglas, Peaceman and Rachford made some comparisons with experiment but did not include cases in which gravity was important nor cases involving displacement by the nonwetting phase.For these reasons, a test of the two-dimensional method for a case in which these factors are included would be very desirable. The test selected was a comparison of calculated results with those from a carefully controlled laboratory experiment on a model with measured physical properties. The model selected was one in which gas displaced oil down a tilted, rectangular sand pack. The model can be thought of as representing a vertical cross-section taken parallel to the dip of a reservoir. The displacement thus simulates gas displacing oil downdip that might result from gas-cap expansion or gas injection. This report outlines the calculation method used

By W. R. Purcell, C. S. Brooks

The internal surfaces of rocks which are in contact with interstitial fluids are known to influence in some degree the recovery of hydrocarbons from pay zones. Despite the admitted importance of the influence of solid surfaces on hydrocarbon recovery, little information is available concerning the extent of surface of reservoir rocks. In this paper a description is given of the apparatus and procedure employed in the determination of the surface areas of sedimentary rocks, and values are reported for a variety of sandstone and limestone cores. In addition, consideration is given to the Kozeny equation, which relates surface area to porosity and permeability. A colliparison is made between the surface areas as calculated from this equation and the geometrical areas of a series of packs of spherical glass beads. Also, for a group of sandstone cores. Kozeny areas are compared with surface areas as determined by the gas adsorption method employed in this investigation. INTRODUCTION It has long been recognized that many processes which are of importance to hydrocarbon production are controlled in some degree by the extent of the surface of the reservoir rock through which the hydrocarbons move. For example, the recovery efficiency that is obtained in a given reservoir is certainly determined in part by the action of interfacial forces between the reservoir fluids and rock, and this action is influenced in turn by the extent of solid surface. Despite the admitted importance of surface effects to problems of petroleum recovery, little information is available concerning the extent of surface of reservoir rocks." It is the purpose of this paper to describe an apparatus which has been employed for the measurement of the surface areas of rock samples and to present the values which have been obtained for a variety of sandstone and limestone cores. In addition, the relationship of surface area to permeability and porosity, as given by the Kozeny equation, will be discussed. METHOD OF MEASURING SURFACE AREA The method of determining surface areas as employed in this work has previously found wide use in studies of porous solids such as catalysts. The method involves the measurement of the amount of physical adsorption of an inert gas, such as nitrogen or argon, on the bare surface of the solid at reduced pressure and constant temperature near the normal liquefaction temperature of the gas. With the aid of the theory of isothermal adsorption as developed by Brunauer, Emmett, and Teller,' it is possible to ascertain the amount of gas (and hence the number of molecules) which is required to cover the solid surface with a single layer of molecules. From a knowledge of the covering area per molecule the total surface ares of the solid can be computed. Since the Brunauer. Emmett, Teller (BET) theory has been adequately discussed elsewhere: it will suffice here merely to present their final equation as ordinarily employed for surface-area calculations. This equation relates the volume of gas, V, which is adsorbed at pressure, P, to the liquefaction pressure, Po, of the gas, and to the volume of gas, V.,, that is required to form a monomolecular layer: In this equation C is a quantity which is related to the heats of adsorption and liquefaction of the gas; for a particular solid-gas system at Constant temperature, C is considered to have a constant value. The basic adsorption data can be presented in the form of Equation (1) by plotting the quantity P/V(Po- P) as a func-

Jan 1, 1952

By G. C. Kuczynski

Two particles in mutual contact form a system which is not in thermo-dynamical equilibrium, because its total surface free energy is not a minimum. If such a system is left for a certain period of time, the bonding of the two particles will take place in order to decrease the total surface area, even though the temperature is lower than the melting point. This phenomenon of bonding of two or more particles with the application of heat only and at temperatures below melting point of any component of the system will be called sintering, although the powder metallurgists use this term in a broader sense, including the presence of molten phase and pressure. It is the objective of this paper to study this process and the mechanisms involved in it. This problem is of utmost importance to powder metallurgy and powder ceramics, and its technological aspects have been studied for a good many years. However, the powder metallurgical operations are too complex and include too many superimposing mechanisms, and too many variables for a direct study. It was therefore advisable for the purposes of this study to reduce the variables to a minimum. In this work the radius of the interface formed during bonding in a simple system composed of a spherical particle and a large block of the same metal was studied as a function of time and temperature. It is believed that the mechanism involved in this simple process is fundamental to any sintering operations. Previous Work J. Frenkell was the first to make a serious attempt to develop a theory of sintering. He assumed that the process consists of a slow deformation of crystalline particles under the influence of surface tension which reduces to a viscous flow where the coefficient of viscosity n is related to the self-diffusion coefficient D by the following equation 1 _ D D6kT [1] where 6 is interatomic distance, k the Boltzman constant, and T the absolute temperature. This type of viscous flow of a crystalline substance is essentially different from the ordinary plastic flow. The latter is a specific propcrty of crystals and cannot take place in amorphous bodies. According to Frenkel this viscous type of flow is due to the diffusion of the holes or vacancies arising in the lattice. He was able to derive an equation relating the growth of the interface between two spherical crystalline particles or between a particle and a semi-infinite crystal (Fig 1) to time t at constant temperature. This relationship can be written as follows: x²— 3/2 a/nt [2] where x is the radius of the interface assumed to be circular, a the original radius of the sphere and a surface tension of the material. The other assump- x tions are that x is less than 0.3 and that during the period 1 the original radius, a, of the metallic particle did not change appreciably. A. J. Shaler and J. Wulff2 followed closely the ideas of Frenkel in their theory of sintering of a mass of metallic powder. Neither Frenkel nor Shaler has validated his theoretical speculations with conclusive experimental data. Two measurements reported by

Jan 1, 1950

By K. H. Adams, T. Vreeland

The basal stress-strain behavior, dislocation density, and strain vale sensitivity of the flow stress uqere measured at room temperature on single crystals oj-zone-refined zinc , 99.999 pct Zn, and zinc containing 0.0025 and 0.02 wt pct Al. No significant change in the stvain rate sensitivity of the flow stress occurs with the addition of aluminum. Changes in dislocation substructure and nonbasal dislocation density were obserrled with the addition of aluminum. The effect of aluminum on the basal slress-strain behavior is explained in terms of changes in nonbasal dislocation density which determines the separation distance of junctions between basal and nonbasal dislocations. The onset of basal slip is associated with the breaking of attractive junctions. The chunge in basal dislocation density was found to be proportional to the one-third power of the plastic shear strain, indepedent of purity. THE effect of impurities in solid solution on the stress-strain behavior of single crystals has been the subject of many theoretical studies. These studies have generally concentrated on the interactions between impurities and dislocations to explain the hardening effeet of impurity additions. The theories that have been proposed include those of yott and Nabarro,&apos;l&apos; Cott-re11; Suzuki; and Fisher. In practice, it is generally difficult to predict the relative importance of the vari- ous effects due to impurities. In addition, secondary effects of impurity additions such as induced changes in dislocation density and substructure in the as-grown crystals have received little attention. Many experimental investigations have been conducted on the effect of impurities on the stress-strain behavior of fcc crystals. Hcp crystals have not received much attention except for the extensive work of Levine et a1.= on magnesium alloy crystals. Stuwe~&apos;&apos; has studied the effect of copper impurity on the critical shear stress of zinc crystals and has interpreted the results in terms of the impurity atmosphere model of Cottrell and Jaswon. This report presents the results of an experimental study of the effect of aluminum additions to zinc on the basal stress-strain curve and the strain rate sensitivity of the flow stress. Etch pit techniques were used to measure and characterize the dislocation density and substructure in the zinc alloy crystals. EXPERIMENTAL PROCEDURE Specimen Preparation. Compression test specimens of four different purities of zinc were prepared from CP grade zinc of 99.999 pct purity obtained from the New Jersey Zinc Co. An analysis of this material furnished by the supplier indicated the following impurities in wt ~ct: Pb = 0.0002; Fe = 0.0002; Cd = 0.00005; other <0.60011. A quantity of material of this grade was further purified by zone refining. Zone refining was carried out under a helium atmosphere by passing a double &apos;One furnace Over a 6-ft-10ng charge at the rate of 2 in. Per hr. * total of ten double zone passes were made before the charge was removed from the furnace. The first one third of each charge was used to grow single crystals. Quantities of two

Jan 1, 1969

By System By John E. Owen, Walton J. Greer

The guard electrode system measures the resistivity of formations by employing a thin disk of current which is caused to flow perpendicular to the bore hole. The control of this current disk is obtained in a brute force manner through the use of relatively long equipotential electrodes above and below the measuring electrode. The log obtained from the system is free of "lag," "plateau," "shadow," "reflection" and other distortions evident on conventional logs. The proportionate contributions of the hole size and invaded zone resistivity to the apparent resistivity reading are reduced when the mud and filtrate resistivities are lower. Thus, the guard system favors the use of conductive muds. The mathematical development of the theory is given in an appendix. Equations are derived to evaluate the effects of mud resistivity, hole size, invaded zone resistivity and depth, and the true formation resistivity. Sample logs from several provinces are reproduced and compared with conventional electric logs to illsutrate the much greater detailed lithology that can be presented by the guard electrode system. INTRODUCTION With increased ability of those in the petroleum industry to analyze formation characteristics from electrical resistivity data, there has become apparent the need for more precise measures of that parameter. The measurement of the resistivity of a homogeneous and isotropic material can be made simply when the body of the material is infinite in all dimensions and the measuring electrodes can be placed within the body. In such a case, the current leaving an electrode follows a spherical distribution and the mathematical expression for the potential level at any distance from that electrode can readily be derived.&apos;.&apos; If it is considered that the active electrodes are within a bore hole filled with mud of a resistivity different from that of the formation. the current does not flow in a spherical pattern near the current source or sink, and the calculations of potential levels become more difficult. The additional consideration of a section of formation invaded by mud filtrates, and thus having resistivity different from either that of the mud, the adjacent formations or of the undisturbed formation, makes the mathematical problem extremely complex. Should the vertical dimensions of the formations be considered as finite. the problem becomes so complex as to preclude reasonable solution. Yet, even these considerations have not described adequately the conditions encountered in a large proportion of the wells to be studied. In efforts to evaluate the effects of the various conditions. combinations of twn, three. and four electrode logging con- figurations of the conventional types have been used. The resulting logs have left much to be desired in some provinces. It has become apparent that the use of such configurations will not result in adequate measurements being made, particularly in cases where the formation is composed of thin sections. If all the current of a resistivity measuring circuit is made to flow through the formation opposite the exploring electrode, many of the shortcomings of the conventional measuring system are eliminated. In the guard electrode method of electrical well logging to be discussed in this paper, the current is so controlled by causing it to flow in a thin disk normal to the axis of the logging tool. EARLY HISTORY The guard electrode method of electrical well logging in its early years was a joint development by the Geophysical Research Corp. and the Amerada Petroleum Corp. The method was first experimentally investigated by means of model studies. The results of these studies indicated that current focusing systems properly applied to electrical well logging

Jan 1, 1951

By Fred D. Rosi

Introduction There is probably no field in which materials research has played a greater role than that of electronics. However, to trace present and future patterns of materials research in electronics is not an easy assignment, since this industry has a high degree of dynamism in its growth, and is busily engaged today in the scientific improbabilities of only recent yesterdays. On the other hand, this task seems especially appropriate since electronics is a truly frontier industry - one whose place in American industries has advanced from 50th prior to World War II to 6th in 1967, with sales of more than $22 billion. And this growth has been associated with the equally rapid progress of science and technology over the period - in particular with the emergence of materials science as a vital force in underscoring this progress. For several reasons this parallel growth is not too surprising. First, by its very definition electronics is a science that essentially deals with the nature, behavior, detection, generation, control and utilization of electrons in solids or at their surfaces. Second, in the electronics industry, systems are made of an integration of components, and these components with their interconnections are made of materials. Thus, the basic building blocks of systems are materials; and it has been largely the advances in materials research and technology that have led to new and improved devices and systems. It follows, therefore, that the broadening of the frontiers in electronics through the exploration of new territories is tantamount to scientific discovery and materials innovation to a degree found in no other major industrial activity. But to put this in the proper perspective of present and future materials trends, it would be appropriate first to survey historically the progress in electronics by pointing out major scientific discoveries and associated materials research patterns that have led directly to its tremendous growth. Then from this base we can consider recent trends in materials research that could form the basis for future progress in the electronics industry. In my review I shall examine the areas most familiar to me, so I must acknowledge at the outset that this survey is not all-inclusive.

Jan 1, 1971

By S. R. Maloof, W. R. Mitchell, J. A. Mullendore

Preliminary experimental evidence is presented to show that the metallic impurities aluminum, iron, and silicon, and beryllium oxide as found in commercially pure hot-pressed beryllium powder can be reduced to lower Concentrations by Zone -Purification techniques. The reduction in the concentration of aluminum to extremely low levels (10 PPm) is noteworthy, since earlier work demonstrated that aluminum is a major factor contributing to the hot-tearing of beryllium during fusion welding. On the basis of present findings, a method is suggested for producing beryllium metal of improved weldability. EXPERIMENTAL research now being conducted on the purification of beryllium indicates that several of the metallic impurities and beryllium oxide can be reduced to lower concentrations by employing standard horizontal zone-refining techniques. For the preliminary work, commercially-pure hot-pressed beryllium having a purity of 97.84 pct was used. The chemical composition is given in Table I. The hot-pressed beryllium was machined into bars 5/8 by 5/8 by 4 to 6 in. in length. Beryllium-oxide boats which had been conditioned by prior heating in a vacuum of 10"5 mm of Hg at 1100°C for 3 hr were used to hold the beryllium while it was zone melted. The boat with its charge, along with a smaller beryllium-oxide boat containing scrap beryllium to be used for gettering purposes, was loaded into a quartz tube and evacuated to 10-6 mm of Hg. Alter alternately evacuating and flushing three times with purified argon, the furnace tube was backfilled to a pressure of 1/6 atm of A and sealed off by means of a vacuum-tight stopcock. It was then removed from the pumping equipment and mounted on the traveling carriage of the zone-refining apparatus. Heating was accomplished with a 10 kw 450 kc induc- tion heating unit using an induction coil consisting of two turns of 3/16-in. diam copper tubing. Before starting to zone melt, the atmosphere in the furnace tube was gettered by heating the scrap beryllium in the smaller boat to above its melting point and holding at temperature for several minutes. The carriage was then shifted so as to locate one end of the beryllium ingot in the large boat within the induction coil. A molten zone approximately 3/4 to 1 in. was established by loading directly into the ingot. The molten zone was moved very slowly along the length of the ingot. Before each pass was made the procedure for evacuating, flushing, and backfilling, and so forth was repeatedI&apos; Speeds of 1 1/2 and 3 in- per hr were used with up to twelve zone passes. The appearance of a typical zone-refined ingot is shown in Fig. 1. After zone refining, the grains in the ingot appear to be elongated in the direction of zone travel, whilst before, they are essentially equi-axed. A microexamination revealed the presence of a network in the beryllium grains as seen in Fig. 2. Laue spots in back reflection pictures taken of the sample were not sharp, indicating the presence of subgrains in the structure. As can be seen, however, many of the network boundaries cross beryllium grain boundaries. It has been shown by Martin and Moore1 that beryllium solidifies as a bcc structure which then transforms to the hexagonal structure at about 1250oC.It is believed that the observed network is merely the outline of the bcc structure which formed from the melt and are not subgrain boundaries. In order to eliminate surface contaminants, approximately 1/16 of an inch of material was removed from the outer skin of each ingot after zone refining.

Jan 1, 1962

By Samuel S. Wyer

The art of natural-gas compressing is now over 25 years old, and has grown at practically the same rate as the increase in domestic natural-gas consumers. There are now over 200 natural-gas compressing stations in North America, aggregating more than 320,000 hp. of compressor capacity and representing a property value of more than $22,000,000, and compressing more than 85 per cent. of all the gas used. The age and magnitude of the art make it evident that the use of gas compressors is a recognized integral part and universal custom of the natural-gas business. The public also is not without its rights and vital interests in this problem. Approximately 1,700,000 domestic natural-gas consumers in North America are dependent upon gas compressors for their natural-gas service. That is, if the use of compressors were to be prohibited, the majority of these consumers would be unable to secure adequate natural-gas service. Each consumer represents between four and five persons, and it therefore follows that the comfort and well-being—as far as natural-gas service is concerned—of at least 8,000,000 persons would be affected if the use of natural-gas compressors should be prohibited. These 1,700,000 consumers have invested, in services, house piping, fixtures, and appliances, an average of about $90 each, or an aggregate of $153,000,000, which is much more than the companies&apos; investment in gas compressors. Furthermore, in all cases where the rate paid by the consumers is fair to the gas company—considering the value of the service rendered by the gas company—the consumers are entitled to continued service and protection of the investment they have made on the faith that the gas service would be continued in the future. Since "Customs adopted and acquiesced in, if not in conflict with federal or State legislation, have the force of positive law,"l and (&apos;Courts will take notice of whatever ought to be generally known withxn the limits of their jurisdiction,"2 there ought to be no question as to the un-

Jan 1, 1916

Jan 1, 1977

By A. U. Seybol

Eight binary iron alloys were examined after ion nitriding experiments to determine the behavior of the following elements: Al, Mo, Mn, Si, Ti, V,Cr, and C. Only Al, Cr, Ti, and V additions caused hardening in binary iron alloys. A few steels were examined to see the effect of Cr, Cr + Al, Cr + Ti, and Cr + V. It is suggested that a useful new class of ni-triding grade steels might be those containing about I pct V. The nitriding of steel, first described by Fry1 about 45 years ago, rapidly attained commercial application with very little knowledge of the fundamentals involved. While Fry,&apos; in describing the status of nitriding in 1932, apparently correctly postulated hardening by precipitated nitrides, the details of the nitriding process were not understood, nor has the situation changed much since that time. It is also interesting to note that the compositions of some typical nitriding steels given by Fry at that time have changed little in the intervening years. Currently used nitriding steels owe their surface hardening to either chromium (as in 4340 steel) or aluminum plus chromium as in the Nitralloy grades, where both CrN and AlN appear to contribute to harden ing. Titanium additions have been studied experimentally, but thus far titanium steels have not won wide commercial acceptance. This subject will be expanded later. The orthodox ammonia nitriding process has been reviewed very adequately many times as in Jenkins3 and Case and VanHorn,4 and their is no need to outline the process here. Ion nitriding is not as well-known, although there have been several descriptions5-9 of the process given, sometimes with comparisons with the ammonia process. Most of these papers are primarily concerned with a description of the equipment, or of the physics or electrical engineering aspects of ion nitriding, but Noren and Kindbom9 gave the results of a metallurgical investigation using both processes. In brief, ion nitriding is carried out in a vacuum chamber from which the air is exhausted and replaced by a N2-H2 mixture, typically containing 10 to 20 pct N2, at about 5 to 10 torr pressure. While ammonia gas has also been used in ion nitriding, there is no evidence that ammonia makes any improvement in the ion nitriding process. A few hundred volts dc is applied between the grounded container wall (positive) and an insulated center post supporting the work (negative) to be nitrided. A glow discharge is created in the ionized gas, accelerating positive nitrogen ions to the work. These ions contain enough energy to form the normally unstable Fe4N "white layer", thus establish- ing surface nitrogen solubility characteristic of the a Fe/Fe4N equilibrium. This creates a substantial concentration gradient, driving dissolved nitrogen into the steel. The temperature employed is in the same range (around 500" to 550°C) as in ammonia nitriding, but because of factors which are not understood at present the nitriding time is ordinarily considerably reduced in ion nitriding. Other advantages have been cited,9 but it is not the purpose of the present work to contrast the two processes. The present objective was to examine the behavior of binary iron alloys during ion nitriding with respect to the microstructure, hardness level, and depth, and to examine some of these factors in steels as well. In this way it was hoped to be able to find out something about the individual role of these elements in steels. While all the work was done by ion nitriding, there seems to be no reason why any conclusions reached would not equally apply to ammonia nitriding, excepting only the kinetic aspects of the process. Another objective was an exploration of the critical-ity of the ion nitriding variables: gas composition, pressure, temperature, and time. EQUIPMENT AND MATERIALS The equipment used was substantially as described by Jones and Martin.8 The vacuum tank was about 12 in. in diam by about 18 in. high, and consisted of water-cooled stainless steel, with a single small window at the top for viewing inside. This sat on a heavy mild steel base equipped with the main pumping port, pressure control port, and vacuum gaging. A series of variable resistances was interposed between the glow discharge and a large-capacity -40 amp variable primary transformer feeding a 1000-v transformer, but 600 v were about the maximum ordinarily used. With the small l-in.-round, 4-in.-thick discs used for nitriding, the electrical load was usually about 500 v at 0.8 amp. The specimen temperature was controlled by a stainless-steel sheathed chromel-alumel couple, whose junction was in the steel stool upon which the flat discs were placed. These were ground through 400 Sic paper. Cycling of the temperature controller caused -0.2 amp variation in ion current, providing an ample control band. The binary iron alloys were made from vacuum-melted hydrogen-deoxidized electrolytic iron and alloys of 99.9 pct purity. Cast ll-lb-square tapered ingots were forged and hot-rolled to about 11/4-in.-diam rounds. Discs of 1/4 in. thickness by about 1 in. diam were machined from the rods for nitriding specimens. The following alloys were prepared: 1 pct each of Mn, Mo, Cr, Ti, Al, V, Si, and an Fe-0.8 pct C alloy. EXPERIMENTAL VARIABLES Of the variables total gas pressure, nitrogen partial pressure, temperature, and time, only nitrogen partial pressure was found to be critical to the operation. A critical nitrogen partial pressure was found corre-

Jan 1, 1970