Search Documents

By W. B. Lewis, M. C. Leverett

The dynamic behavior of a multiple fluid system is completely describable in terms of driving forces and resistances to flow. The latter are proportional to the viscosity of the fluid under consideration and inversely proportional to a property of the system termed the " effective permeability " to that fluid, a property therefore defined by this relation. Since three phases are usually present in oil reservoirs, it is essential to know the effective permeabilities to the several fluid phases, and the relationship between the composition of the fluid in the pore space and that of the flowing stream, in order to handle satisfactorily certain problems of oil production. In this regard, there are many unknown factors and parameters, and many that can be evaluated only indirectly. However, it is expected that work along lines similar to this present undertaking will help materially in solving these problems. .. . . Previous workers in this field have investigated the two-phase systems, water-gas,' water-oil2 in unconsolidated sands, and water-gasg in consolidated sands. The extension of the study of the flow of heterogeneous fluid systems from two to three phases involved only slight changes in technique. The apparatus used in the present work, except for slight changes to be described, was that used by Leverett in his water-oil experiments.~ Correlation and interpretation of data were made by methods analogous to those used in two- phase work. The relative permeability to a phase—the effective permeability divided by the permeability of the system to a homogeneous fluid—was employed throughout in correlating the rate of flow of that phase with the composition of the pore space. Quantitative measurements of two independent physical properties of the system were required to determine the composition of the pore space. As in the two-phase work, the fraction of water was determined electrically, The gas fraction was determined by measuring changes in volume accompanying measured pressure changes. Suitable account was taken of the solubility of the gas in the liquid phases, and of the vapor pressure of the water phase. Since this work was exploratory in nature, no attempt was made to obtain highly accurate numerical results. Reasonable precision and reproducibility were sought. Experimental Procedure variables Considered.—Of the properties of the fluids, the oil viscosity is most likely in practice to vary widely. Variations in oil viscosity were therefore included in this work, but variations in other properties of the fluids are as yet unexplored. It appears unlikely that the normally encountered variations will produce significant changes. ~h~ observations were made at fairly high pressure gradients, no attempt being made to detect a variation of the relative permeabilities with pressure gradient. It should be pointed out also that since most of the data were taken on one sand size only, it call Only be assumed at present that changes in

Jan 1, 1941

By B. W. Prof. Frazier

(Read at the Wilkes-Barre Meeting, May, 1877.) THIS interesting application of the laws of thermodynamics to metallurgical practice has not been discussed by any writer, within my reading, except the late Prof. Gallon of Paris. In his Cours de Machines,* Prof. Callon has given a short but lucid discussion of this subject in the admirably clear style for which he was remarkable. Although the interest attached to the subject is rather theoretical than practical, I have thought that an attempt to explain the mechanical action exerted in the hot-blast oven might not be entirely devoid of utility, especially in the suggestions which it involves. The statement, that the mechanical work performed in heating the blast is, when high temperatures are produced, considerably greater than the work performed by the blowing-engine, may seem incredible to many who are practically acquainted with the subject, appearing, as it does, to conflict with the results of their experience. It is, nevertheless, literally true, and I shall attempt in this paper to prove it, and to explain why it has not rendered itself palpably manifest in practice. Before proceeding to the mathematical demonstration, it will be well to recall to mind the definitions of some terms employed by writers in mechanics and thermodynamics. The actual energy of a moving body, as defined by Rankine, is the work which it is capable of performing against a retarding resistance before being brought to rest, and is equal to the energy which must be exerted on the body to bring it from a state of rest to its actual velocity. The value of that quantity is the product of the weight of the body into the height from which it must fall to acquire its actual velocity. * Vol. I, chap. x, [§ ] 4, p. 312.

Jan 1, 1878

By B. W. Frazier

This interesting application of the laws of thermodynamics to metallurgical practice has not been discussed by any writer, within my reading, except the late Prof. Callon of Paris. In his Cours de Machines," Prof. Callon has given a short but lucid discussion of this subject in the admirably clear style for which he was remarkable. Although the interest attached. to the subject is rather theoretical than practical, I have thought that an attempt to explain the mechanical action exerted in the hot-blast oven might not be entirely devoid of utility, especially in the suggestions which it involves. The statement, that the mechanical work performed in heating the blast is, when high temperatures are produced, considerably greater than the work performed by the blowing-engine, may seem incredible to many who are practically acquainted with the subject, appearing, as it does, to conflict with the results of their experience. It is, nevertheless, literally true, and I shall attempt in this paper to prove it, and to explain why it has not rendered itself palpably manifest in practice. Before proceeding to the mathematical demonstration, it will be well to recall to mind the definitions of some terms employed by writers in mechanics and thermodynamics. The actual energy of a moving body, as defined by Rankine, is the work which it is capable of performing against a retarding resistance before being brought to rest, and is equal to the energy which must be exerted on the body to bring it from a state of rest to its actual velocity. The value of that quantity is the product of the weight of the body into the height from which it must fall to acquire its actual velocity.

Jan 1, 1879

By H. G. Dwyer

CONSIDERATION for future expansion influenced the design of the new smelter at Chuquicamata. The section of the smelter now going into operation, while large, represents only little more than half of the ultimate plant. Equipment for the direct smelting of raw concentrates has been arranged in the conventional manner although needless details have been eliminated wherever possible while mechanical and electrical features not usually found in copper smelters have been incorporated. Access is afforded to all equipment but platforms and walkways have been held to a minimum. The poling and other platforms in the converter aisle, normally subjected to battering by ladles and other heavy equipment in transit, are of concrete construction with steel grid armor embedded in the exposed surfaces. Noticeably absent are the many platforms formerly required for the handling of converter flux since this material is charged to the converters through the side walls of the converter uptake hoods. Clear space with ample headroom is provided under each converter and converter puncher's platform to permit clean-up by small bulldozers. Remote controls have been introduced at many points. Electrical control rooms and control centers have been conveniently located. An electrical tunnel with cross tunnels and escapeways is situated under the entire length of the converter aisle for power feed lines. Skull breaking facilities are in a separate building near the smelter. A silica-slurry building with brick storage area is adjacent to the smelter building so that elevator service is available to both buildings. A smelter office, a change house and lunchroom are provided in convenient locations. Units of the smelter as presently constructed are shown in the plan and table on page 1194. The ultimate smelter will house 7 reverberatory furnaces, 14 waste-heat boilers, 9 Peirce Smith converters, 4 casting furnaces serving 2 casting wheels, and one holding furnace serving a straightline casting machine. Additional crane requirements in the converter aisle will necessitate the installation of special hoisting equipment in space already provided in a raised section of the roof over the casting end of the aisle. Thus a complete crane may be lifted high enough above the crane rails to permit the passing of another crane underneath thereby giving all cranes full use of repair facilities already installed. For the collection of gases, 2 dust chambers, each with separate stacks, will collect converter gases and 2 balloon flues with separate stacks will collect reverberatory furnace gases. Extensions necessary to complete the ultimate plant will be possible with little interruption to normal operations since the future converters and reverberatory furnaces will be added at the east end while additional casting facilities will be added at the west end of the present plant. The future units may be added singly or all at one time depending on requirements.

Jan 1, 1952

By Morris Cohen

Within the past two years, a number of publications have called attention to the double peaks, or stages, that appear in the hardness and strength curves of certain aging alloys. The author has shown the existence of double hardness peaks during the aging of a high-purity silver-copper alloy;' and on the basis of electrical resistance, microscopic, dilation and lattice-parameter measurements, hc concluded that the initial hardness peak occurs prior to precipitation while the secondary hardening is due to precipitation. It was suggested that the general mechanism of age-hardening involves two consecutive processes, the first consisting of nucleus or knot2 formation, and the second consisting of actual precipitation and particle growth. It was further held that the two stages are interdependent, but because of nonuniform precipitation they may overlap each other to an extent that increases as the aging temperature is raised. At high aging temperatures, the effect of the first stage cannot be detected because of the rapid occurrernce of precipitation. The general theory of age-hardening recently presented by Dr. M. L. V. Gayler3 is in close agreement with the picture outlined above. With reference to work done on duralumin, copper-beryllium and copper-silver alloys, Dr. Gayler also concluded that age-hardening takes place in two consecutive steps: first, diffusion (in which the solute atoms migrate to certain crystallographic planes), and then precipitation. However, W. L. Fink and D. W. Smith4 have shown that the double aging peaks that appear in the strength curves of high-purity aluminum-copper alloys may be explained without recourse to pre-precipitation phenomena. By means of very careful metallographic technique, Fink and Smith demonstrated that during aging the precipitation takes place at an accelerated rate along the grain boundaries and slip planes as a result of the plastic deformation caused by the drastic quench from the solution heat-treatment temperature. The general precipitation occurs at a

Jan 1, 1939

By Tracy L. Atherton

The mapping of slant-hole oil fields is complicated by the fact that relationships between wells are subject to variations in three dimensions and are not readily adaptable to representation on a plane surface. Formalized perspectives usually expand into an undecipherable maze of lines and peg models with the necessary supporting dividers serve only to awe the beholder with their perplexity. The usual compromise arrived at is a plotting of the projection of the courses of all of the wells in the field onto a horizontal plane (Fig. I). These complicated plots, when used in conjunction with the individual vertical projections of the wells, heretofore have been the most practical foundation for the study of general field problems. This method has many shortcomings, however, which arc not found in the recently developed straight-hole equivalent projec-tion method. The new method supplies a series of maps similar to the type now in common use in straight-hole fields. It is remarkably simple to use and supplies a ready check on clearances between wells. Perhaps the method can best be understood if the steps that led to its development are described. Common practice of oil-well surveyors is to supply the owner with a tabling of the survey and a plan view plotted against the true meridian. If a vertical projection is plotted, it is usually plotted separately and shows vertical depths against the projection of the stations along a section line joining the top and bottom of the hole on the plan view. A more practical method would be to plot the section line of the plan parallel to the abscissa of the vertical projection (Fig. 2). If this is done, any line parallel to the "base line1' will pass through the points on each projection that represent a single point in the hole. Another very useful graph, which the well surveyor could provide, would be plotting of vertical depths against measured depths. Fig. 3 illustrates the next step facilitated by this form of plotting. The lines designated "well A" represent the proposed course of a hole to be drilled. Superimposed on the drawing, in its proper relative position, is the plan view and a portion of the vertical projection of a present producer, well B." From an inspection of the plan view we arrive at the correct conclusion that the only indicated possibility of collision is at the point of crossing of the wells on the plan view. Referring to the vertical projection, note that the vertical depths of stations on B, in the vicinity of the crossing, are plotted on the same plane of projection as A. The clearance is the indicated distance between the two vertical sections measured along the parallel to the "base line," which passes through the point of intersection of the plan view. Repeat this process for the other wells crossing the proposed course of A on the plan view and you have a preliminary check of clearance for the proposed course. A similar comparison of crossings on the vertical projections of all >

Jan 1, 1941

By J. H. Hensley

The mine of the Miami Copper Co. is in the Miami district, Gila County, Ariz., approximately 7 miles west of Globe. In 1906, the General Development Co. secured the ground now owned by the Miami Copper Co., and about a year later discovered ore in a prospect shaft at a depth of 220 ft. The Miami Copper Co. was organized in 1907, the claims held by the General Development Co. were transferred to it, and an active development campaign was inaugurated. The railroad was extended from Globe to Miami in 1909, a concentrating plant was constructed, and the company began producing early in 1911. The unit size of mineral tract in the district is the standard lode claim 600 ft. in width by 1500 ft. in length. Ownerships of land are held in fee. The geology of the district has been described by F. L. Ransome.' The formations of local importance are: The pre-Cambrian Pinal schist, which consists mainly of metamorphosed sedimentary rocks and is commonly of a thinly laminated sericitic variety; the diabase, which is thought to have been intruded in late Paleozoic or early Mesozoic times; the Schultze granite and granite porphyry, considered early Tertiary; the dacite of late Tertiary time; and the Gila conglomerate of early Quaternary. General Items Influencing Mining Methods The bodies of disseminated ore in the district are flat lying masses of irregular outline and variable thickness. As a rule, these masses lack definite boundaries; the orebody follows a curve along one of the main ridges, approximately 5500 ft. in length with a maximum width of 1600 ft. The minerals occur as finely divided and uniformly disseminated chal-cocite in the Pinal schist and Schultze granite. The typical overburden or capping is a barren rusty brown, very friable, highly siliceous, leached schist, or granite-porphyry. The topography of the district is fairly rugged and irregular; the altitude ranges from 3400 ft. above sea level, at the town of Miami, to 3900 ft. on the hills above the Miami orebody. The climate is mild; the mean annual temperature is 63.°F.

Jan 1, 1925

By B. D. Crawford, S. A. Falconer

ONE of the outstanding achievements in connection with this country's war efforts has been the ability of our mining industry to supply from domestic sources many of the minerals of strategic importance that formerly were obtained principally from abroad. In order to meet the war-born demands for these scarce minerals, it has frequently been necessary to develop special methods for treating ores and waste products hitherto considered too low-grade to be workable; and to improve the efficiency of older beneficiation processes. Important in this respect have been the recent technological advances in the field of froth flotation of nonsulphide minerals. Because of the refractory nature of many of these domestic ores, and, in many cases, the limited available technical data regarding their treatment, much research work has been necessary. The following examples describe the procedures and reagents used, and the results obtained, in certain laboratory flotation investigations conducted by American Cyanamid Company's engineers at the Cyanamid Ore Dressing Laboratory on ores containing such minerals as scheelite, manganese oxides and carbonate, ilmenite, brookite, kyanite, garnet, spodumene, mica, feldspar, celestite, fluorite, chromite, corundum, and cassiterite. In presenting these data, we wish to point out that many of the minerals listed have previously been tested, and their amenability to flotation reported, by other investigators-notably those of the United States Bureau of Mines. In some instances the procedures and reagents used in the treatment of some of the following described ores follow rather well-established lines, and with one or two exceptions, the reagents used were well known. However, many of the ores tested did not respond well to simple conventional procedures and it was necessary to adopt special methods of conditioning and desliming, reversal of the usual order of floatability of some of the minerals, multiple cleaning, etc., in order to secure separations. Except where otherwise noted, all numbered and trade-marked reagents mentioned in this paper are marketed by the American Cyanamid Co. or the American Cyanamid and Chemical Corporation. TUNGSTEN ORES Tungsten minerals, vitally important in the war industries of the United States, rank high in the list of those we formerly had to import in order to supply our needs. Most of our domestic ores of tungsten contain scheelite as the valuable mineral. Today there are in the neighborhood of twelve tungsten operations in this country where flotation is used as the main or accessory form of benefication. It has, of course, been known for some time that scheelite and other tungsten minerals respond to treatment by flotation.

Jan 1, 1944

By C. R. Hocott, Stuart E. Buckley

The viscosity of the oil in the reservoir is one of the properties that influence its movement through the sand to producing wells. Measurements of viscosity, therefore, are pertinent to problems associated with well behavior and with the estimation of recoveries, and afford an indirect means for partial evaluation of various methods of controlling reservoir behavior. The effect of dissolved gases on the viscosity of crude oil has been determined,ls2 but no data have been published on the viscosity of representative samples of reservoir oils. This paper describes a simple instrument that has been used to determine the viscosities of a number of subsurface oil samples at the temperatures and pressures existing in the reservoirs, and presents the results of the determinations for typical fields. Construction oF the Apparatus The principal requirements of any instrument used for the examination of subsurface samples are that it be strong and simple both in design and in method of operation. Accuracy beyond that of the degree of reproducibility of subsurface Sam-~les from various wells in a reservoir or exceeding that of the common measure-merits of reservoir temperatures and Pressures is not required. Because of the expense of procuring subsurface samples, it is necessary also that the instrument operate on a relatively small fraction of a sample, leaving the remainder for other tests, and that there be few or no failures of the equipment to cause undue delay or loss of a sample. After preliminary experiments with a falling bullet, the results of which were not satisfactory, a simple viscosimeter was built of the rolling ball type first proposed by Flowers3 and later used by several investiga-tor. 5.8 The apparatus consists essentially of a removable, accurately bored cylindrical barrel of 1/4-in. nominal internal diameter, 8 in. long, in which a closely fitting steel ball rolls through the oil with the barrel inclined at a definite angle. The ball makes contact at one end of the barrel with ail insulated electrode, closing an electrical circuit, which actuates a buzzer. The meas-urements consist essentially in determining the time required for the ball to travel the length of the barrel. The details of the construction are shown in Fig. I. The barrel in which the ball rolls was made from a section of 25-caliber blank rifle barrel, specially bored to an exact uniform diameter and polished. The barrel slides snugly into a hole bored in a solid stainless-steel cylinder, an upper external shoulder of the barrel compressing a small spring, and is held in place by a hollow nut. The spring prevents the barrel from seating against the bottom of the bored hole in the cylinder, while narrow external longitudinal slots in the barrel permit fluid to flow around it and through the bottom. The upper part of the recess in the steel cylinder is enlarged to form a tapered chamber, which acts as a reservoir for the oil and affords space for agitation to ensure

Jan 1, 1941

By A. W. Ambrose

The underground losses of oil exceed by hundreds of thousands of barrels all the oil that has been lost in storage, transportation, or refining. The quantity lost is, of course, indeterminate; but when it is considered that the contents of an entire oil field have been excluded from recovery by invading waters, some idea of the amount wasted may be gained. Similarly, enormous quantities of gas have been lost underground. Conservation of the oil, therefore, should start before it is brought to the surface rather than after it is placed in storage tanks. Water is one of the most important causes for underground losses and the operator should give as serious consideration to an underground flood of water as he would to a destructive surface flood. The best insurance, of course, is to have the wells drilled in such a manner that water has no access to the productive oil and gas horizons, and on abandonment the wells should be properly plugged. The encroachment of edge water and the occurrence of waterin;the base of an oil sand present a very serious problem to an oil company sooner or later these waters are bound to cause considerable damage, if they do not entirely destroy the possibilities of further production. Too often, however, a field has been considered to be in a hopeless condition, whereas wells in as bad a condition in other areas have been repaired and the life of the field appreciably lengthened. The corrections are very often suggested by technical study. Very successful results have been accomplished by detailed underground work in the California oil fields, in Cushing, Oklahoma, and in other areas. The purpose of this paper is to outline briefly1 general methods of analyzing oil-field water problems in a producing or in a producing and developing oil field, with a view to suggesting repair work on offending wells. Reference is continually made to producing oil wells; the same general method of procedure, however, should be adopted in a gas field.

Jan 1, 1921

By E. H. Rose

The present symposium on flotation machines provides a unique opportunity for group reappraisal of standard or habitual viewpoints. A symposium is by definition a trading post- for observations that might prove complementary when put together, thus leading to useful thoughts that might not have been evident from the original observations individually. The present paper, pertaining to power consumption in flotation, is deliberately an experiment of that kind. Data were solicited from the operating superintendents of several of the major flotation plants on this continent. The information received, covering a total of 14 separate operations in seven plants, has been collated in terms of power intensity; that is, the total power input per cubic foot of cell volume. This departs somewhat from the conventional expression of power per ton of ore treated, though the latter figure is also given for the plants concerned. Because of wartime restrictions, particularly in Canada, identifying names of plants and machines are withheld. Not as a firm conclusion, but as a tender for symposium discussion, the following points are made: 1. That flotation is a power operation in much the same sense as ball milling. 2. That contact time is the complement of power intensity and may be decreased as the latter is increased. 3. That a decrease in flotation power per ton of ore can result from an increase in power intensity. Analogy with Grinding In grinding, it has become axiomatic that the more the power put into a given operation, the greater the work performance. The analogous view is now proposed that the effectiveness of any flotation operation will be related to the mechanical energy usefully applied to that operation. Under this view, each increment of properly directed input energy should give either an increase in unit tonnage or an improvement in the metallurgical separation (concentrate grade or tailing grade), until either the theoretical limit imposed by mineral constitution or surface condition is reached, or until further increments of power become uneconomic under the law of diminishing returns. Thus, as in grinding, there are two forms of output that greater power input or improved utilization of power can produce. As for the law of diminishing returns, lower unit cost of power through improved generating efficiency in the past decade has pushed the limit back. Over and above this, however, there is strong indication in the operationg data herein presented that higher power intensity results in an actual economy of over-all power consumption. Like crushing and grinding, flotation accomplishes a rupture of the forces of molecular attraction, by taking particles from the common environment and placing them in the two separate environments of

Jan 1, 1947

By Robert E. Tally

Underground fires have been common in the mines of the United Verde Copper Co. for the past 22 years. The first fire started in the 300 Hampton stope in the fall of 1894, following a cave in that orebody. The soft and highly pyritic nature of the ores is responsible for most of these fires. Since ore characteristics, methods of mining and ventilation, have an important influence on mine fires, they will be described in this paper. Orebodies The ores are mostly chalcopyrite except on the upper levels where considerable chalcocite, black oxides and other secondary minerals occur. The orebodies are in the form of lenses and vary in size. Some are small, while others are several hundred feet in length by a hundred or more feet in width. These orebodies extend, in some cases, from the surface to the lowest levels of the mine and usually at a steep angle of inclination. There are three different classes of ores, classified in accordance with the gangue rock. The copper in all cases, except as above specified, is in the form of chalcopyrite. The largest and most important of these reserves are in a pyrite gangue. Next in order of importance are the schist ores and lastly the quartz porphyries. The pyrite, locally termed iron ores, average from 30 to 42 per cent. sulphur. The schist and quartz porphyries vary from 3 to 25 per cent. sulphur. Mining Methods All the orebodies were worked by the overhand square-set method of mining prior to 1908; since then the cut-and-fill, shrinkage and mill-hole systems have been largely employed. But 15 per cent. of the total tonnage now extracted is from timbered stopes. Most of this is from the upper levels where the ore is soft, heavy and more or less broken to the surface. Large reserves of these ores are being conserved for more efficient methods of mining.

Jan 1, 1917

By A. W. Cochardt

THERE are a number of effects that can cause material damping or internal friction. Some of these are frequency dependent, such as the thermo-elastic effect' and the stress-induced ordering.' Others depend on the amplitude of vibration, i.e., the damping related to the motion of dislocations3 and that due to magneto-mechanical hysteresis.' While many of these effects have been studied, only the magneto-mechanical effect has found extensive practical application. It is the principal source of damping in the current blade material in steam turbines.A magneto-mechanical hysteresis loop is seen in Fig. 1. If an unmagnetized, polycrystalline wire of a material exhibiting magneto-mechanical hysteresis, such as an Fe-14 pct A1 alloy, is twisted in torsion, a relation between shear stress and shear strain y is observed as indicated. The stress-strain curve does not follow Hooke's law -dashed line. Instead, the strain y increases nonlinearly and partly irreversibly, due to the motion of ferromagnetic domain walls,* until a critical stress is reached, which in this case is about 3,500 psi. If the applied stress is raised further, the strain appears to increase linearly and reversibly in accordance with Hooke's law, since all domains are now aligned in easy directions of magnetization nearest to the direction of the applied stress, and plastic flow has not yet started noticeably. On removing the applied stress, a remanent shear strain y, is observed, which is related to the irreversible magnetostriction of the material.' The energy dissipated in the material during a stress-strain cycle is proportional to the critical stress t, and the remanent magnetostrictive shear strain 7,. The purpose of this investigation was to make a survey of the magneto-mechanical damping of ferro-

Jan 1, 1957

By I. Havenaar

Various methods have been proposed in the literature to calculate the pressure losses in drill-pipe and bit-nozzles, i.e., those parts of the mud-circuit where the largest pressure-losses occur. Very few data, however, are available to check the validity of these proposals. Presented in this paper are the results of pumping experiments with clay-water drilling fluids of different specific gravities and different laminar flow-properties (differential viscosity and Bingham yield value), using pipes of different diameters. In addition, a series of measurements on bit-nozzles is discussed. Two main conclusions may be drawn from this work for the flow through pipes. 1. In the laminar flow region pressure losses can be calculated from the differential viscosity and Bingham yield value of the mud. 2. In the turbulent flow region pressure losses can be calculated with good approximation from a viscosity term which is determined by the volume fraction of the dispersed phase. Calculations making use of laminar flow properties may lead to erroneous results. The effect of temperature on the pressure losses in the case of turbulent flow can be calculated from the change in viscosity of the dispersing medium, i.e., water. The main conclusions determined for the flow through bit-nozzles are that for flow conditions prevailing in the field, the pressure-drops in bit-nozzles are independent of the laminar flow properties of the mud. They are solely determined by the density of the mud and the geometry of the nozzle. INTRODUCTION The last decades have witnessed a steady increase in the depth of oil wells. This is illustrated by the increase in the drilling depth record in the USA from 8,046 ft in 1927 to 21,482 ft in 1953. This increasing depth, together with the experience that high rates of mud circulation and high fluid velocities in the bit-nozzles enhance the rate of drilling, has emphasized the importance of selecting suitable mud-pumps when starting the drilling of a deep borehole. For such a selection it is necessary to be able to calculate the pumping pressures necessary to obtain the required circulation rates. The main part of the pressure-losses in the mud circuit occur in the drill pipe and the bit-nozzles. Various methods have been proposed in the literature to calculate the pressure-losses in the drill pipe1,2,3,4. These methods do not all lead to the same results, and at the time this investigation was started insufficient basic data were available to check their validity. Moreover, to our knowledge, no data are available at all on the effect, if any, of the flow-properties of the mud on the pressure-losses in bit-nozzles.

Jan 1, 1955

By A. H. Geisler

INTRODUCTION THE correlation of property changes during precipitation with structure has progressed, sometimes rapidly but other times more slowly, since the fundamental discovery of Merica, Waltenberg and Scott.1 The predominent factor that hampered the progress has been limitations imposed by the various detection methods. Refinements in X ray diffraction techniques and in metallographic methods, which have been extended by the electron microscope, have contributed new information within the last few years. These permit an extension of the theory as proposed by Mehl and fetter in 1940.2 Now that a suffcient number of alloys has been investigated to establish a general mechanism of the precipitation process, a correlation of the facts into a generally applicable theory of age-hardening is both warranted and desirable. 'I he purpose of the paper is to provide an orderly correlation of the phenomenological facts of precipitation hardening. Speculation on mechanism of hardening will be confined to that consistent with existing theories of hardening. Age-hardening accompanies the formation of a new structure, the precipitate, as provided by an alloy system in which solid solubility decreases with decreasing temperature. Upon this premise alone all such systems would be expected to include age-hardenable alloys. Alas, this is not always the case. Few attempts have been made to explain the variable degree of age-hardening among different alloys or to explain the influence of small alloying additions upon the hardening. Dispersion hardening as originally postulated3 is not adequate.* Coherency hardening-the term that will be used to distinguish the properties of a two-phase mixture in the unique and unstable transition state at which the phases are strained into precise atomic registry (continuity or coherency) in planes

Jan 1, 1948

By A. M. Gaudin

A GREAT number of hypotheses has been advanced to explain the complex phenomena that are encountered in flotation. In the days of bulk-oil flotation, when a large quantity of oil was employed, it was observed that the oil-mineral aggregate floated above the ore-pulp because of its lesser density. With the advent of froth-flotation this phase of the theory had to be modified to take into-account the presence of air bubbles.. The reason why the mineral-bearing froth of today rises to the top of flotation cells is, of course, because the air-mineral aggregate, with whatever reagent may be associated with it, is lighter than the pulp. In an attempt to explain froth-flotation the fact has been emphasized that certain minerals are wetted and therefore remain in water; while others are not wetted and therefore become associated in preference with air. Such an "explanation" does not explain facts, it merely states them; for instance, it does not explain why minerals are wetted under some circumstances and not wetted under others. Going somewhat further, the wetting or nonwetting of minerals by water has been ascribed' to differences in the angles of contact between oil droplets and mineral surface at the surface of the minerals. This explanation, however, was abandoned when soluble flotation reagents came to replace the so-called "insoluble" reagents. Another theory, sponsored about 10 years ago by Ralston,2 involves the effects of electric charges at the surface of the mineral particles and air bubbles. This theory, unfortunately, was not developed as fully as it seems desirable. The belief that adsorption phenomena might play a preponderant role in flotation3 has been rather widespread for the last 10 years. Unfor-

Jan 1, 1928

By W. C. Ellis, M. E. Fine

In the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;' the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition2 which has a large effect on other properties. The thermal expansion data for the system have been reported only from room temperature to 100 C and for this temperature range a minimum in coefticient in the rcgion of 50 at. pct cobalt is well established.3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the tcrrelation. Experimental Procedure The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 5c pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 1/2 in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for I hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,? the differential expausion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outcr silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested On a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A nonoxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1949

By Nicholas J. Grant, Robert F. Wilde

TAYLOR and Floyd's"" work in establishing phase diagrams based on the elements Ni-Cr-Ti-A1 has led to an understanding of the precipitation hardening mechanism in alloys based on these elements. Nordheim and Grant4 concluded that in simple alloys, and where the aluminum to titanium atomic ratio was such that less than three out of five aluminum atoms were replaced by titanium, the precipitate on aging is the face-centered-cubic Ni 3A 1 phase, called They further found that increasing amounts of hexagonal ? phase, Ni3Ti, precipitated from these alloys when the titanium content exceeded the solid solubility of both matrix and Ni3A1. For alloys of Ni-Cr-Ti-Al, in which the titanium and aluminum contents each ranged from 0 to 4 wt pct, the titanium-rich was superior for strengthening to either pure ?' or 7. It was also noted that the combined titanium plus aluminum content (atomic pct) was a direct measure of the high temperature strength and overaging temperatures for these alloys.4 The present investigation was undertaken to extend existing data on precipitation hardening in the more complex commercial alloys containing higher titanium plus aluminum, and with significant quantities of cobalt, molybdenum, and carbon. Experimental Procedure Reforging of As-Received Bar Stock—The alloys were received as ground, forged bar stock. Chemical analyses and the as-received bar diameters are shown in Table I along with the ASTM grain size after the various treatments. All stock except the Waspaloy was reforged to % in. diam to gain material and to facilitate machining of stress-rupture specimens. Forging was carried out at 2100°F, and discontinued when the bar temperature fell to 1800°F. Heat Treatments—For experixental simplicity it was desirable to heat treat all of the alloys at, the

Jan 1, 1958

By George W. Hezzelwood

THE Balatoc mine, one of the Haussermann group,[t] is on the Island of Luzon, the largest of the Philippine group, about 260 km. north of Manila, and 12 km. from the city of Baguio. The Baguio district is the most important gold-mining area of the Philippines, with 14 producing mines in 1939, milling 2,3;8,894 tons of ore, yielding [P]40,881,048, approximately 55 per cent of the total Philippine production of [P]74,131,216. PRODUCTION HISTORY The Balatoc mine began production in January 1929 with a 150-ton cyanide mill. Increases in mill capacity have taken place as follows: March, 1932, to 350 tons June, 1933, to 470 tons December, 1933, to 515 tons July, 1934, to 700 tons December, 1934, to 1000 tons May, 1935, to 1200 tons October, 1938, to 1300 tons April, 1939, to 2000 tons January, 1941, to 2150 tons Production during the period of expansion has steadily increased in total value in spite of the fact that grade of ore milled has dropped-from $31.06 in 1929 to $5.78 in 1940. Annual reports give production as shown in Table 1, the average values being based on gold at the old price of $20.67 per ounce. [ ] GEOLOGY The ore occurs in quartz-calcite veins that vary in width from narrow stringers to mineralized zones 40 to 50 ft. wide. Wall rocks consist largely of diorites, with some andesite, and a fragmental breccia called locally the "Balatoc plug." Texture of the ore varies widely in the different veins-from a soft, highly altered, gouge material filled with quartz fragments through a soft, unaltered quartz-calcite to a hard, massive quartz ore. Three major vein systems have been extensively developed, and smaller amounts of work have been done on several others. These veins strike east-west to N. 60°, dipping south from 50° to 90°, and are essentially tension breaks between a series of faults or shears striking N. 30°E. to N. 50°E. and dipping southeast from 50°to 90°. The shear veins and tension veins probably formed more or less simultaneously,

Jan 1, 1942

By Thomas A. Read

THE internal friction of single crystals of metals is affected markedly by a variety of factors, which, according to the literature, are without influence on the internal friction of polycrystalline metals at strain amplitudes less than 10-5. For example, the internal friction of a suitably oriented zinc single crystal is multiplied by a factor of l00 when the vibration amplitude is slightly increased, and the internal friction of a copper crystal is markedly increased by the application of a stress of 30 lb. per sq. in. for one minute. In this paper it will be shown that these, together with the other phenomena associated with the damping of mechanical vibrations in metal single crystals, can be satisfactorily explained, at least qualitatively, in terms of an atomic mechanism that has been proposed for quite another purpose-that of accounting for slip in metals. The extraordinary agreement between the observed behavior of the metal single crystals and the behavior that could be predicted on the basis of this atomic mechanism leads to the belief that the latter is probably essentially correct. If this is so, it follows that valuable information about the slip process in metals may be gained from measurements of internal friction on single crystals. In this paper the results of the only study to date on the damping of mechanical vibrations in single crystals of metals will be presented. EXPERIMENTAL PROCEDURE The internal friction of a material is a measure of the rate at which the energy of mechanical vibrations is converted into heat. The measure of internal friction used in the present paper is the decrement A, which is defined as the fraction of the energy of vibration lost per half cycle. The measurements described here were .made for longitudinal oscillations at a frequency of 33.5 kc. for the copper crystals, and at a frequency of 39 kc. for the zinc crystals. The method used is that of the composite piezoelectric oscillator. The single-crystal specimens are in the form of circular cylinders ¼ in. in diameter and 1 ½ to 2 ½ in. long. The crystal rods are waxed in a V-block and sawed to the proper length with a fine jeweler's saw. The ends of the specimen are ground flat, and one end is cemented with a very thin film of beeswax and rosin to the end of an x-cut quartz rod which is ¼ in. in diameter and 3 in. long. The length of the specimen rod is determined by the condition that its natural frequency for longitudinal vibration be the same as that of the quartz rod, within 0.5 per cent. The lengths of the specimens are thus different for different orientations of the cylinder axis with respect to the crystallographic axes. When the specimen and quartz rods are thus matched in frequency the adhesive is at a node of stress, and it has been shown experimentally that under these circumstances

Jan 1, 1941