Search Documents

By S. Jana, C. M. Wayman

The reverse transformation of bcc martensite to the fcc phase was studied in an Fe-33.95 wl pct Ni alloy by nzeans oj dilatometry, melallography, and electron microscopy. Upon "slozc" heating (-1°C per min) length cJmnge us temperature plots showed u gradual contracLion over the temperature range 200" to 280"C ,followed by a more abrupt contraction beginning a1 -280°C. Howet,ev, zchen the heating rate was increased -4°C per tnin, no gradual contraction was observed and only the abrupt contraction starting at -2BO"C was found. Thus on slower heating- the AS "temperature" for the subject alloy, unlike the MS temperature, is better defined as a range of temperatures. Both optical and transmissiorl electron microscope observations showed that some of the martensite plates exizibited a partial loss of transformation twins during reversal. The midvib region of the martensite plates disappeaved relatively early duirng the reversal. Metallographic observations slowed that the earliest detectable stage of the rezlerse tvansforrvration begins (axd Moues inulardly) at The Martensens i te - parent interface. At higher temperatirres, the. formation of martensitically reversed jcc plates within the bcc martensite plales was observed. It is concluded that the reverse transformation consists of a diffusion less process (martensitic); but this is ps-obably aided by a prior or simultaneous dijjusiorz-comltvolled process, at leasl in the case of slower heat-ing' experiments. ALTHOUGH numerous investigations have dealt with the parent-to-martensite ("forward") transformation (fcc — bcc) in Fe-Ni alloys, comparatively little is reported on the ("reverse7') martensite-to-parent transformation.'-4 Even though such reverse transformations have been studied in detail in some nonferrous systems, one of the difficulties of studying the reverse transformation in most ferrous mar-tensites is that the martensite decomposes by tempering during heating. However, carbonless Fe-Ni alloys do not exhibit this difficulty since the transformation in these alloys is completely reversible. The present investigation represents an attempt to shed more light on the nature and mechanism of the martensite-to-parent transformation. 1) EXPERIMENTAL PROCEDURE 1.1) Alloy Prepatation. Fe-Ni alloys of compositions near 34 wt pct Ni were prepared from zone-refined iron (99.994 wt pct Fe) and high-purity nickel (99.999 wt pct Ni) by induction melting in recrystallized alumina crucibles in an argon atmosphere, with prior vacuum evacuation to 10"3 mm Hg. The alloys were homogenized by induction stirring in the molten state for 5 min. After solidification, the alloys were further homogenized in evacuated quartz capsules for 96 hr at 1230°C. 1.2) Dilatometry. Slices of the ingot were hot-forged (750°C in air) into approximate rod form and these specimens were then hot-swaged (750°C in air) into long cylindrical rods 0.55 mm diam. From the rods, specimens about 1 in. long were cut. These were then vacuum-annealed for 24 hr at 1200°C, cooled to room temperature, and subsequently transformed to martensite in liquid nitrogen (whereby about 40 pct transformation was obtained). Dilatation measurements were made by observing length changes in a vacuum dilatometer with an externally mounted LVDT sensing element. 1. 3) Preparation of Electron Microscope Specimens. Slices of the ingots were cold-rolled (with intermediate vacuum anneals) to -0.020 in. Out of these rolled sheets, specimens (about 1 by 1 in.) were cut. These were then vacuum-annealed, transformed to martensite by cooling in liquid nitrogen, and subsequently heated from room temperature to various temperatures to effect either partial or complete reverse transformation. These specimens were then chemically polished to 0.002 in. in l:l HsOz (30 pct) and &PO4 (85 pct) solution, and thinned to electron transparency in an electrolyte consisting of 150 g CraOs, 750 ml glacial acetic acid, and 30 ml ~~0.~ Observations were made with a 100-kv Hitachi HU-11 electron microscope equipped with an HK-2A tilting device. 1.4) Optical Microscopy. Metallographic observations were made with a Leitz MM5 metallograph on the same 0.020-in. sheet specimens as were used for electron microscopy and on bulk specimens which were 0.2 in. or more on a side. The chemical thinning solution when cooled below 20°C also served as an etchant for this alloy. Observations of surface relief were made with a Zeiss interference microscope employing a Thallium light source of wavelength 0.54 p. Specimens for interference studies were prepared by two-stage polishing on Buehler vibromet polishers using 0.3 and 0.05 p alumina abrasives. 2) EXPERIMENTAL RESULTS 2.1) Comparison of the MS,AS, and Af Tempera-tures wTth Previous Re sults. The AS aLd Af tempera -tures of several Fe-Ni alloys were determined dila-tometrically. The MS temperatures of the same alloys were determined by continuously lowering the temperature using a mixture of isopentane and liquid nitrogen and observing the highest temperature at which a prepolished specimen showed surface upheavals. For the present the As temperature is defined as the temperature at which an abrupt decrease in length occurs in the dilatation plot. The Ms,As7 and A determinations in the present investigation and those of Kaufman

Jan 1, 1968

By J. H. Waxweiler, L. C. Ikenberry, R. J. Bendure

Carbon which is present as insoluble carbides in austenitic stainless steels can be measured quantitatively by dissolving the steel in iodine-methanol and analyzing the residue for carbon. Severe sen-sitization was observed in Type 302 due to precipitation of only 0.003 pet carbon. Both cold work and the presence of delta ferrite caused a marked acceleration in rate of carbide precipitation. Carbide precipitation rates in 17-7 PH were stzulied for the austenite conditioning and also the aging heat treatment. CARBON and its compounds exercise a major influence on the properties of stainless steels and their response to thermal treatment. Sensitization in 18-8 type stainless steels has been the subject of numerous investigations throughout the years. Bain, Aborn, and utherford," and Binder, Brown, Frankss all studied the effects of heating austenitic stainless steels in the temperature range of 1000° to 1500°F. The primary purpose of most of these studies was the investigation of susceptibility to in-tergranular attack in acids due to these sensitizing heat treatments. Intergranular precipitation of carbides was always associated with intergranular attack but it was recognized2 that severe attack could occur with but minute quantities of precipitated carbide. Mahla and ielsen utilized the electron microscope to make a significant contribution in illustrating the appearance and method of growth of chromium carbides during sensitizing heat treatments. However, as they stated, their studies of residues could not be used to obtain a quantitative measurement of the amount of carbon which was actually precipitated. The aim of the present investigation was to devise a relatively fast, simple method for the quantitative measurement of carbides in stainless steel. EXPERIMENTAL WORK The initial investigations were made to determine the best means of separating carbides from the matrix. A number of dissolving media were tried using both chemical and electrolytic attack. Qualitative examination of the extracted residues by X-ray diffraction indicated that solution in iodine-methanol would furnish a good means of separation. Consequently, further work was pursued along this line. The method is quite simple. The sample in the form of millings or nibblings is dissolved in iodine-methanol solution at room temperature (6-g iodine, 25-ml methanol per g of sample). The insoluble residue containing the carbides is separated by suction filtration through an ultra-fine glass filter disc. This is a very fine filter medium that will retain particles as small as 0.1 to 0.2 p in diameter. After washing with methanol and drying, the filter disc and residue are placed in a conventional combustion carbon-tube furnace and the carbon determined gravimetrically. Using this technique it was found that reproducible insoluble carbon values were obtained. However, since such small amounts of insoluble carbon were obtained on Type 302 after sensitizatipn at 1250°F and 1500°F, the values were confirmed by a second method. In the second method the sample was dissolved with copper potassium chloride and filtered through a millipore paper. This treatment dissolves the matrix but leaves undissolved practically all of the carbon irrespective of how it is present in the steel. The amount of insoluble carbon present as chromium carbide is determined by calculation from the analysis of the residue for chromium and iron. The derivation of the formula used for this calculation is discussed later. The values obtained by the indirect copper-potassium-chloride method were in agreement with those obtained by the iodine-methano1 method. See Table I. It should be pointed out that the sensitivity of the direct combustion method is not too high when the amount of carbide present is small. This is due primarily to inherent blanks and to analytical errors such as weighing. For this reason it cannot be stated with any degree of certainty that there is a significant difference between values of 0.002 and 0.005 pct. Having confirmed that the iodine-methanol extraction gave a quantitative measurement of the precipitated carbides in Type 302, exploratory tests were conducted on Armco 17-7 PH stainless steel. Samples from commercial Heat 54807 were solution annealed at 2000°F, water quenched and heated at 1250" and 1500°F, and water quenched. The analysis of Heat 54808 is as follows:

Jan 1, 1962

By D. A. Elgillani, M. C. Fuerstenau

In this paper, oxidation potentials measured in the presence of various concentrations of cyanide, ferro-cyanide, and ferricyanide and ethyl xanthate at various values of pH are related to flotation response. Eh-pH diagrams are presented to show that the formation of surface ferric ferrocyanide is probably responsible for depression when cyanide is added. The influence of cyanide on the depression of pyrite with xanthates as collector has been the subject of a number of investigations,'-6 and several theories on the mechanism of depression have evolved from these studies. Wark and Cox7 and Gaudin8 have suggested that the depressing effect is due to a competition of cyanide ion with xanthate ion for the surface. Cook and his colleagues9-11 have explained this phenomenon in terms of competition between hydrocyanic acid and xanthic acid. Sutherland 12 has shown that although both of these theories accurately describe the relation between pH value and cyanide addition at constant collector addition, they fail to describe the relation between pH value and the amount of collector required to cause flotation. Taggart 13 suggested that depression in these systems is due to the formation of a reaction product between ferric ion at the pyrite surface and ferrocyanide ion derived from solution. Majumdar4,6 has attempted to prove this hypothesis by measuring the contact angles of pyrite in the presence of 25 mg per liter ethyl xanthate and different concentrations of potassium ferrocyanide and ferricyanide. In all cases the contact angles were quite high up to pH 10. These results indicate that pyrite should not be depressed by either potassium ferrocyanide or ferricyanide. In view of these facts, Majumdar has assumed that the compound Fe(CN)2 forms at the surface. Gründer and Bornl4 have stated that depression may be due to the formation of the compound K2Fe(II)Fe(CN)6 at the pyrite-solution interface. This compound is thought to be an interaction product between the K2Fe(CN)6-2 ion from solution and the Fe++ ion at the pyrite surface and, accordingly, K4Fe(CN)6 should depress pyrite at least as effectively as KCN. This was proven experimentally, but there was no simple relation between the depression of pyrite and the concentration of either KCN or K4Fe(CN)6 in solution. In view of the many mechanisms that have been proposed for pyrite depression by cyanide, it is apparent that a clear understanding of the phenomena occurring in these systems is lacking. One reason for this may be the fact that the species responsible for pyrite flotation in the presence of xanthate is not the xan-thate ion but rather dixanthogen.15 Since the oxidation of xanthate to dixanthogen is dependent on the oxidation potential of the solution, it would seem that knowledge of these potentials would be a requisite to understanding the pyrite-xanthate-cyanide system. It is the object of this paper to measure both the oxidation potential and pH of the pyrite systems in the presence of various concentrations of cyanide, ferrocyanide, and ferricyanide and xanthate and to relate these values to flotation response. EXPERIMENTAL MATERIALS AND 'TECHNIQUES In the experiments discussed here, pure potassium ethyl xanthate was used as collector, and reagent grade potassium cyanide, potassium ferrocyanide, and potassium ferricyanide were used as depressants. Reagent grade HC1 and KOH were added for pH adjustment. Conductivity water, made by passing distilled water through an ion exchange column, was used in all experimental work. Two natural samples of pyrite were used in the investigation. Sample preparation for flotation included dry grinding with a mortar and pestle and sizing the product to 100 x 200 mesh. Prior to flotation, a 0.75-gm sample of pyrite was added to a solution containing a known amount of depressant at the desired pH value, and the system was conditioned for 4 min. Following this, a known amount of collector was added and the system was conditioned for another 4 min. The pH — termed flotation pH - was measured; the pulp was transferred to a Hallimond cell, and flo-

Jan 1, 1969

By O. P. Arora, M. Metzger, G. R. Ramagopal

The rates of grain boundary and general corrosion were surveyed by an approximate method. Quantitative differences between their variations with the strength or cupric ion content of the acid yielded large variations in their ratio, highly selective intergranular attack being observed only under specific chemical conditions. The boundary corrosion rate increased with the copper content of the aluminum; this was attributed to an autocatalytic effect similar to the one shown for general corrosion. High- purity aluminum in hydrochloric acid exhibits striking intergranular corrosion and other structure-dependent corrosion phenomena of fundamental interest. The behavior is highly sensitive to the metallurgical and chemical conditions, the significance of many of which has not been established. The features of the intergranular-corrosion phenomenon, first described by Rohrman,l are summarized in the remainder of this paragraph. Strong attack normally occurs only at high-angle grain boundaries.' Usually 15 to 25 pctHCl is used to obtain a high rate, but this has also been obtained with weaker (7 to 15 pct) acid either by adding cupric or ferric ion to the acid3-5 or by passing an anodic current (-0.1 ma per sq cm).2,3,5,6 The two latter corrosion conditions produce strong attack of low-angle boundaries after certain heat treatments 2-4,5,7 The susceptibility of high-angle boundaries is influenced by the grain-boundary segregation of iron atoms; this increases the slow (µ per month) attack in 10 pct HCl8 but diminishes the rapid (mm per month) attack in 20 pct Hc14 (the present and most previous investigations deal with rapid attack). That segregation of elements other than iron affects intergranular corrosion has not been demonstrated, although analysis of data for iron alloys indicated that at least one other element must be considered.9 Intergranular attack occurs over a wide range of purity although it begins to become obscured above several hundred parts per million (ppm) total im- purities by the severe general corrosion which accompanies the higher iron contents and which is associated with the presence of a second phase or an inhomogeneous distribution of the dissolved iron.4,6,10 The variation of intergranular-corrosion rate with heat treatment1'3-6'"10 can be explained in some cases in terms of the distribution of the iron impurity but is not in general adequately understood. The present work dealt with two questions not previously considered in detail. The first proceeded from the view that the extent to which a special behavior is associated with the boundaries is indicated not by the intergranular corrosion rate alone but by the ratio of the intergranular to the general corrosion rate. A comparison of the two rates was therefore made for one lot of aluminum in acids of varying strength and metallic ion content. The second question was the effect of the copper content of the aluminum. For general corrosion, it has long been known that copper ions introduced into the acid by corrosion of the solid solution are reduced on the aluminum as patches of elemental copper which enhance the corrosion rate by providing cathodes of lower hydrogen overvoltage than were originally present.''-'3 Since the copper patches remain themselves unchanged, their action is "catalytic", and since they are products of corrosion, the effect is "autocatalytic." This phenomenon is significant at copper levels much lower than previously suspected, even at those typical of high-purity aluminum, as the authors have shown in a previous paper.l4 The present work shows that copper content affects intergranular corrosion. With polycrystalline specimens, truly quantitative rate measurernents are not readily made for intergranular corrosion or for general corrosion in the presence of rapid intergranular attack, and previous work in this field has tended to be qualitative. The present study made use of a simple procedure which provided fair approximations to the quantitative corrosion rates and fitted the purpose of surveying the behavior over % wide range of conditions and displaying certain large effects. The approximations involved in this work were usually outweighed by the experimental scatter, which tends to be substantial in a system as sensitive as this one. I) EXPERIMENTAL A. Material. The material procured, Table I, represented three low copper (1 to 3 ppm) lots, two of "normal" copper content (21 and 22 ppm), and two

Jan 1, 1962

By T. E. Kihlgren

SYSTEMATIC data are presented on the relation of composition of nickel silvers to color, tarnish resistance, hardness and liquidus temperatures, for alloys containing up to 30 per cent nickel and 50 per cent zinc, further modified at certain nickel and zinc contents by 0 to 8 per cent of tin and 0 to 10 per cent of lead. Attention has also been directed, using a still more limited range of alloys, toward a study of tensile properties and such casting properties and characteristics as fluidity, shrinkage and pressure tightness. In some of these, rather broad ranges of composition are dealt with; in others, it has been expedient to focus attention on the Federal Specification 20 per cent nickel silver casting alloy, WWP-541. INTRODUCTION The demand for an alloy essentially white in color, which could be cast and worked by simple methods and which possessed strength and corrosion-resisting properties superior to the usual brasses, led to the discovery and early use of cupronickel alloys containing zinc, and some-times tin, lead and other metals. This type of alloy was generally known as German silver until the war, when the term "Nickel Silver" became generally accepted. The element principally responsible for the white color of the alloy and for its strength and corrosion resistance is nickel, which may constitute from 8 to 30 per cent of the alloy. The functions of the other elements will be described later. The manifold uses of nickel silver are largely due to its color, corrosion resistance, ease of casting, fabrication, joining and rather moderate cost. In many instances the alloy is finished by grinding and polishing while in others it may be finished with a silver or nickel plus chromium plate. Electroplates

Jan 1, 1935

By H. Larson, J. Chipman

The ferrous and ferric oxide concentrations of slags, expressed as j = Fe+++/(Fe+++ + Fe++), have been established through gas-slag equilibrium at 1550°C in a range of oxygen pressure of 10-I to 10-9 equilibriumatm. The value of j is increased by basic additions (BaO, CaO, MgO, MnO) and decreased by acidic oxides (SiO2 and TiO2). Oxygen pressure is shown graphically as a function of composition for slags which are analogous to those at the slag-gas interface of the open hearth furnace. THE progress which has been made in recent years in understanding the chemistry of metallurgical slags has been based largely on studies of slag-metal and slag-gas equilibria. There is a considerable body of knowledge which is applicable to reactions occurring at the slag-metal interface in open hearth steelmaking. There is little information concerning reactions of the slag with the furnace atmosphere and hence little basis for an understanding of the transfer of oxygen, sulphur, or hydrogen between gas and slag. The oxygen pressure of the open hearth atmosphere is normally of the order of 10-1 to 10-3 atm which differs by several orders of magnitude from that of about 10" atm at the slag-metal interface. The chemical properties of the slag, for example, the ratio of ferric to ferrous iron and the ability of the slag to hold sulphur in solution, are greatly affected by changes in oxygen pressure. This investigation was undertaken to enlarge our knowledge of the effect of oxygen Pressure on steel-making slags. Using air or controlled mixtures of CO a CO2 a range of oxygen Pressures from 10.' to 10.' was covered. Review of the Literature There are only a few references in the literature which pertain directly to this investigation. The most important is that of Darken and Gurry1,2 on the system iron-oxygen. This work included the determination of the phase diagram of the system and also a study of the field of homogeneous melts and their oxygen pressures. Their apparatus and procedure were very similar to that used in this study. Iron oxide was melted in a platinum crucible under an atmosphere of CO2:CO, CO2:H2, H2O, CO2, air or O2 depending upon the partial pressure of oxygen desired. After equilibrium was reached, the sample was quenched and analyzed for ferrous and ferric oxide. By appropriate calculations these authors were able to determine the oxygen and iron activities in the various slags, heats of formation of the oxides of iron, and heats of solution of iron and oxygen in the liquid slags. In a subsequent paper' the same authors made a less thorough investigation of the effects of additions of lime and manganese oxide on the composition of iron oxide melts. Only a few experiments were made and those in a narrower range of temperature and oxygen pressure. Darken' has investigated the fusion temperature of iron oxide in contact with silica under various atmospheres. He found that the temperature changes from 1120° to 1447°C as the gas composition changes from CO2/CO equal to 20.8 to pure oxygen. A comprehensive paper by White" predates the work of Darken and Gurry. The decomposition of ferric oxide into oxygen and lower oxides of iron was studied from 1000° to 1650°C and under oxygen pressures from 2 to 76 cm of mercury. The effect of

Jan 1, 1954

By R. M. Brown, W. J. Murphy, B. M. Kapadia

An investigatiott was conducted to study the influence of nitrogen, titanium, and zirconium on the boron llardenabilzty effect in a low-carbon constructiona2 alloy steel. The experimental steels investigated exhibited a significant variation in hardenability, the variation being dependent on the interactions of boron, titanium, and zirconium with the nitrogen. Only the boron not combined with nitrogen was effective in increasing hardenability. Titanium, and with lesser effectiveness zirconium, combined with available nitrogen, thereby protecting the boron. The hardenabil-ity effect mas related to an empirical expression for the "effective" boron content, P, deduced from experimental evidence of these interactions. The hardenabzlity effect reached a maximum at about 0.001 wt pct 0, and decreased somewhat as P increased further. The physical understanding of this relationship is discussed. FOR many years boron has been added to steels to obtain high hardenability. Although a great deal of research has been conducted on boron-treated steels, certain aspects of the boron hardenability effect have not been fully understood. For instance, the magnitude of the hardenability effect has been observed to vary markedly, depending on the steelmaking technique, even when the amount of boron in the steel was essentially constant. Furthermore, the optimum amount of this element to be added has not been definitely established. A better understanding of the boron hardenability effect is essential because too small an addition of boron is likely to be ineffective, while an excessive amount can cause brittleness'' and hot shortness. The findings of earlier investigations have shown that the hardenability effect cannot be consistently related to the amount of boron added or retained in the steel. Grossmann observed that in a 0.60 pct C steel the hardenability increased to a maximum with mold additions up to about 0.0025 pct B and then decreased with larger additions. Other investigators5 likewise reported a maximum in the hardenability at about 0.003 pct B. Crafts and Lamont, however, found that in commercial open-hearth heats of medium-carbon steel the hardenability increased linearly with boron up to 0.001 pct and remained essentially unchanged with larger percentages up to 0.006 pct. Other investigators7,' also observed a rather constant hardenability effect in the range about 0.0005 to 0.0035 pct B. These observations and other evidence suggest that the effectiveness of boron in increasing hardenability probably depends, in addition to the amount, on the form of boron retained in the steel, this form being influenced by the presence of other elements. Both oxygen and nitrogen apparently exert the strongest influence on the hardenability behavior, since, at the temperature of liquid steel, boron readily combines with these elements, thereby losing its effectiveness as most experimental evidence seems to indicate. For consistent recovery of the boron effective in increasing hardenability, it is necessary that the oxygen and nitrogen in the steel be either reduced to extremely small amounts by the steelmaking practice or neutralized by combination with other elements before the addition of boron. The importance of achieving adequate deoxidation prior to the addition of boron in order to realize the full hardenability effect of boron has been sufficiently emphasized by earlier investigators. Digges and Reinhart' and others have investigated the role of nitrogen and have shown that nitrogen also interacts with boron and reduces or nullifies altogether its effect on hardenability. Moreover, their work also demonstrated that the addition of strong nitride formers such as titanium and zirconium reduce the deleterious effect of nitrogen on boron hardenability by combining with nitrogen to form stable nitrides. Another element which has a pronounced influence on the boron hardenability effect is carbon. It has been shown7'10 that the hardenability effect of boron diminishes with increasing carbon content, and becomes almost negligible at the eutectoid composition. This observation is useful in comparing the potential increase in hardenability from boron of steels with different carbon contents, but is not relevant to a study of the effects of normal steelmaking variables. The amounts of oxygen and nitrogen in steel vary with the steel composition and steelmaking practice employed. Most commercia1 low-alloy steels are fully deoxidized by the addition of silicon and aluminum, or other strong deoxidizers, which adequately protect the boron from oxidation. In addition, one or more of the elements such as titanium or zirconium are usually added, either separately or in combination with boron, in the form of complex ferroalloys, to protect boron from combination with nitrogen in the steel. However, the actual amount and type of addition employed for a given processing requirement are usually selected by trial and error, and have a rather limited range of applicability. As a result, substantial variations in the hardenability of boron-treated steels are often observed in practice, particularly when the nitrogen content of the steel is a significant processing variable. These variations might therefore be reasonably attributed to the interactions between boron, nitrogen, and titanium or zirconium present in the

Jan 1, 1969

By J. D. Alexander, W. L. Martin, J. N. Dew

This paper presents data obtained using a flood-pot technique to determine the fuel available and the corresponding theoretical air requirements for in situ combustion of crude oils. Since the technique is relatively quick and easy, it is a practical and convenient tool for evaluating reservoirs as fireflood prospects. It is also a research tool which facilitates systematic study of the variables affecting fuel availability and corresponding air requirements. The understanding of these variables is of prime importance to those concerned with the technical and economic development of in situ combustion as an oil-recovery process. The experimental results show conclusively that the fuel available for in situ combustion is not a constant but, rather, varies with crude-oil characteristics, porous-medium type, oil saturation, air flux and time-temperature relationships. Thus, the fuel availability for specified field applications should be determined using actual reservoir crude and core material and the process conditions expected during in situ combustion in the reservoir. INTRODUCTION In situ combustion is a thermal process for recovering crude oil from reservoirs. The thermal energy released during the combustion of a small amount of the oil in place aids in the displacement of the remaining oil. Numerous articles have been published describing the in situ combustion process giving detailed results of laboratory and field experiments.10 In order to engineer an in situ combustion project, a number of important factors must be considered and determined. These factors include: (1) the amount of fuel consumed per unit of reservoir volume swept by the combustion zone, (2) the composition of the fuel consumed, (3) the amount of air required to consume this fuel, (4) the portion of the reservoir swept by the combustion zone, (5) the appropriate air-injection rates and pressures, (6) the amount of oil that will be recovered, (7) the rate of oil production and (8) the operating costs. Nelson and McNiell1 recently have described a procedure which utilizes laboratory combustion-tube data as a basis for the calculation of some of these design factors. Various authors have attempted to describe the in situ combustion process mathematically, and considerable progress has been made. Analytical solutions to the problem of heat transfer from a moving combustion front have been obtained for linear and radial systems."-' All of the published results involve the assumptions that: (1) fuel concentration is constant throughout the reservoir, or that fuel concentration is inversely proportional to the velocity of the front for a given rate of oxygen consumption; and (2) the fuel reacts instantaneously with injected oxygen, while liberating a constant amount of heat per unit weight of fuel at all temperatures. It seems both desirable and reasonable to test the validity of these assumptions experimentally. This paper presents laboratory data which were obtained by means of a "fire flood-pot" method for determining fuel availability and composition, and the corresponding theoretical air requirements for in situ combustion of crude oils under variable conditions. The mechanics of the method are similar to a conventional tube-run experiment.' The important differences involve the size of the reservoir model used and the method for providing the experimental environment. The new method subjects conventionally-sized core samples or unconsolidated sands to a programmed environmental sequence similar to that experienced by a similar volume of rock during the approach and passage of a combustion front in a long tube or in an oil reservoir undergoing in situ combustion. Restored-state samples can also be used. The small samples and relatively simple techniques involved allow an experiment to be set up, run and calculated in about three 8-hour days. This is a considerable improvement over long-combustion-tube techniques which can require several days to run and several more work days to set up and calculate. All the runs presented were run at 40-psig injection pressure. Pressure was not considered as a variable for these experiments, since we previously had found that it had only a small effect on fuel availability up to 600 psig.APPARATUS AND MATERIALS APPARATUS The fire flood-pot apparatus consists of a consolidated

By R. F. Rolsten

The preparation of pure metals by the thermal decomposition of volatile halides was developed byde boer' and van Arkel.2 This has proved to be a useful technique for the refining of columbium,the mechanical and physical properties of which are seriously altered by such interstitial contaminants as oxygen, nitrogen, hydrogen, and carbon. The conventional deposition surface of a resis-tively heated metal filament was replaced, Fig. I, with an indirectly heated clear quartz surface. The impure columbium (feed) was contained in the annular space between the Vycor deposition bulb and the perforated molybdenum retaining cylinder. The head assembly was attached to the deposition bulb by fusing the Vycor at "A". This unit was then connected to a vacuum system composed of a three-turn glass coil to eliminate fracture due to vibration or expansion, a McLeod gage, a cold trap, a two-stage mercury diffusion pump, and a mechanical pump. The entire system was cold outgassed, and the 10 to 20 g of iodine in the auxiliary bulb (reservoir) was held in dry ice to prevent excessive loss of iodine. The columbium was hot outgassed at 800" to 825oC with the pressure maintained at l0-5 to 10-6 mm Hg for 48 hr and cooled under vacuum to 200° to 240oC. Iodine was sublimed from the reservoir and collected in the deposition bulb. The feed material temperature was adjusted to give the desired iodide vapor pressure and the finger temperature of 1000" C was independently attained and measured with a platinum-platinum 10 pct Rh thermocouple located in the center of the nichrome wire helical heating element, "F." The system was attended until temperature equilibrium was established, whence it operated without attention. This is a definite ad- vantage over the conventional "hot-wire" technique which required either constant attention or automatic control. In operation, the iodine vapor originally introduced into the vessel reacted with the crude metal to form a columbium iodide. This iodide vapor diffused to the hot deposition surface where it thermally decomposed, depositing columbium and releasing iodine. This liberated iodine then diffused back to the crude columbium where iodide was formed again. Thus, by repetition of this process, the iodine carried pure columbium from the crude material to the filament, where it deposited. The success of the "iodide" process in producing ductile metals depends on preventing the transfer of oxygen, nitrogen, hydrogen, and carbon from the feed material to the deposit. In many cases relatively minor quantities of these interstitial contaminants impair the ductility of metals. The material produced by the iodide process has such exceptional ductility that it is frequently and mistakenly assumed that iodide metal is always of very high purity. This assumption is not necessarily true since a number of metallic impurities can also be transferred. In the present investigation, the temperature of the feed material was adjusted to iodinate selectively and the deposition temperature adjusted to decompose the iodides selectively. By this technique, some metals present in the feed material were prevented from codepositing with the columbium. It is quite important to have the feed material symmetrically located around the deposition surface in order to obtain a uniform deposit at the maximum rate. For example, Runnalls and pidgeon3 observed that, when the base of a titanium filament was about 1 cm from the feed material, deposition was rapid on that section close to the feed, but that the rate decreased with distance from the feed so that a

Jan 1, 1960

By W. G. Bearden, P. P. Scott, G. C. Howard

This paper concerns the rupture or breakdown of rock formations as related to drilling, completing, and stimulating production of wells, and comprises data compiled from a study of literature and records of treatment of oil and gas wells. and from tests conducted in bores drilled into rock cores and outcrops of rock. Results of the investigation indicate that the internal pressure to rupture cylinders of rock and to breakdown rock formations surrounding a bore in the earth is dependent upon the extent of intrusion of fluids. the position of bedding planes. the ratio of internal to external diameter, the tensile strength of rock, and magnitude of confining pressure, and is independent of the size of bore, degree of fluid saturation. and temperature of rock within practical limits. It is concluded that the mathematical relationship of pressure in bores and stresses in the surrounding rock must not be limited by the simplifying assumptions of homogeneity. isotropy, and impermeability; that the incidence of lost circulation of drilling fluids to induced fractures may be reduced by preventing intrusion of fluids into the small intrinsic fractures along weak bedding planes; and that the magnitude of the breakdown pressure of wells to be treated may be lowered by removal of mud cake. INTRODUCTION The purpose of this paper is to present and discuss the results of tests which may serve to broaden the understanding of the phenomena of rupture or breakdown of rock and thus contribute to the improvement of the techniques for drilling and completing wells. including such operations as preventing lost circulation, stimulating production, and placing cement. Since the early recognition of the possibility of rupturing rock adjacent to a well by fluid pressure, the distribution and magnitude of stresses around a well and the internal pressure to cause failure have been expressed mathematically by application of the principles defining the elastic and inelastic behavior of thick-walled cylinders of a homogeneous. isotropic, impermeable material. In either the elastic or plastic state, if the conditions of homogeneity. isotropy, and impermeability were the normal characteristics of rock. there would be no reason to question the validity of the above principles when applied to rock. However. since most rock formations are characteristically permeable to some degree, contain bedding planes and small intrinsic fractures. and are heterogeneous, rendering invalid the assumptions of homogeneity, isotropy, and impermeability, the application of the thick-walled cylinder theories to the behavior of rock formations penetrated by a bore appears illogical. Also the failure to consider the effect of the properties of the drilling fluids, which certainly intrude in various degrees into most rock formations. is further cause for questioning the application of these principles. Even in the case of cylinders of hardened chrome-nickel steel, which would he considered relatively homogeneous isotropic. and impermeable, as compared to rock, it has been observed that the internal pressure capable of being withstood by the cylinders varied with the sizes of molecules comprising the rupturing fluid used. Because of these apparent weaknesses in the theories of the behavior of thick-walled cylinders when applied to bores in rock, and the importance of knowing the true behavior of rock under the influence of fluid pressure when planning drilling and completing procedures for wells, tests were undertaken to determine by observation the actual rupturing pressure of cylinders of rock and the effects of such variables as environmental conditions and characteristics of rock formations, fluid properties, and bore dimensions. It was intended that by these tests the validity of the thick-walled cylinder theories when applied to rock would be determined and, if found invalid, mathematical expressions would be derived for predicting stress and rupturing pressure of rock formations under various conditions. Since the derivation of mathematical expressions has been only partially completed, all of the results of the latter phase are not included in this paper. PROCEDURE The investigation was initialed with a study of the theories pertaining to the rupturing of thick-walled cylinders of homogeneous. isotropic, impermeable material and a study of the

Jan 1, 1953

By P. S. Kotva

Dislocation substructures in superalloy matrices of varyzng co)npositions have been studied. In general, it has been found that the alloys can be classified into ''high", ''medium", and "low" stacking fault energy classes based on the type of dislocation substructure observed in the matrix and that the substructure can be correlated to the stacking fault energy. The effect of different types of dislocation substructure and dislocation reactions on the intragranulur precipitation of carbide phases has been studied. In a Ni-Cv-Mo-Fe matrix, precipitation of MC carbides in association with stacking faults has been observed. In most superalloys, solid-solution strengthening and precipitation hardening are the chief mechanisms employed to achieve strength. The latter contribution to strength is usually achieved by the precipitation of / in certain wrought alloys. Insufficient attention has been given to the problem of obtaining strength in su-peralloys by controlling precipitation of carbides on imperfections within the matrix. The present work was undertaken to investigate the dislocation substructure in various superalloy matrices, to study the effect of such substructure on subsequent precipitation of carbides in the matrix, and to investigate whether certain modes of precipitation of carbide phases found in austenitic stainless steels2"4'6 would occur in nickel-base alloy matrices with dislocation substructures of the same type as those found in austenitic steels. 1) EXPERIMENTAL TECHNIQUES Five-pound heats of the various alloy compositions reported here were vacuum-cast. The ingots were given light deformation by rolling to break up the as-cast structure and then homogenized for 24 hr. HASTELLOY alloy X (nominal composition: Ni-2OCr-17Fe-8Mo-0.05C) was homogenized at 2150°F and In-cone1 625 (nominal composition: Ni-20Cr-5Fe-8Mo-3.5Cb-0.05C) was homogenized at 2280°F. Fabrication of 0.004-in. sheet was achieved by cold rolling with intermediate annealing treatments being carried out at the same temperature as those used for homogeniza-tion. Each solution anneal was followed by quenching. The aim of this procedure was to redissolve as much of the primary carbide phase as possible. Samples of the 0.004-in. sheet were cut and encapsulated in quartz capsules and then heat-treated in the tube furnaces. Thin foils were prepared using an ethanol-10 pct perchloric acid bath at 32°F and at a voltage of 22 v. A "window" technique was employed. Observations were made on a JEM-7 electron microscope operating at 100 kv. 2) EXPERIMENTAL RESULTS a) Types of Dislocation Substructure. Fig. 1 shows a schematic correlation between stacking fault energy, SFE, and the type of dislocation substructure observed in various matrices of nickel- and cobalt-base alloys. A precise quantitative determination of stacking fault energy is not implied in the figure but the correlation between stacking fault energy and the type of dislocation substructure obtained allows alloys to be divided into three classes in analogy with the classification employed by Swann and ~uttin~' for binary alloys of copper. Class I alloys are associated with a "high" SFE and show a cellular substructure of dislocations as typified by the micrograph of a thin foil of pure nickel deformed 4 pct at room temperature in Fig. 2. With decreasing SFE the tendency toward cell formation is lessened and dislocations tend to be arranged in coplanar groupings. Examples of this class of alloys with "medium" SFE are provided by the mi-crostructure of solution-heat-treated, quenched, and deformed thin foils of HASTELLOY alloy X, "Waspaloy" (prior to any aging), and Inconel 625. Fig. 3 shows a thin-foil micrograph of an alloy of Inconel 625 composition, solution-heat-treated, quenched, and deformed 5 pct at room temperatures. No evidence of any cell structure can be obtained in materials of "medium" stacking fault energy, Fig. 3, even after severe deformation. The stacking fault energy of the alloy shown in Fig. 3 is, however, not low enough to make the dissociation of dislocations visually obvious. As stacking fault energy decreases further, with successive addition of solute in the matrix, there is an increased tendency toward dissociation of dislocations and cross slip becomes progressively more difficult. Eventually, when the stacking fault energy is "low" enough, complete dissociation of dislocations is seen to occur as shown in Figs.

Jan 1, 1969

By H. S. Thomsen, W. C. Duesterhoeft, R. E. Hartline

The attenuation and phase shift which formations produce in the electromagnetic field of an induction-type electrical well-logging instrument are great enough to substantially affect the response of the tool to formation conductivity under normal logging conditions. The application of the general equations for the propagation of an electromagnetic field in a conductive medium to the transmitter-receiver coil pair of an induction-logging-tool coil system gives an expression for the response which properly takes the propagation effects into account. A comparison of a calculation of this type with the response computed from the commonly used geometric factor concept, which does not include the propagation effect, leads to a factor Go representing the ratio of the responses computed by the two methods. The value of Go decreases not only with increasing formation conductivity, but also with increasing transmitter-to-detector coil spacing. For a single coil pair with a 40-in. spacing, the value of Go is 0.972 in a 20-millimho/m formation. The value is reduced to 0.915 and 0.812 for conductivities of 200 and 1,000 millimhos/m. As a result, the basic signal generated by the induction-logging coil system is not linearly related to formation conductivity as expected from the geometric factor concept. A uniform conductivity scale can be obtained only by adding a suitable nonlinear element to the recording system. The addition of auxiliary coils, having spacings less than the main-coil span, to achieve focusing results in an even greater departure of the basic signal from linearity with conductivity. The solution of the field equations near the interface between two formations of different conductivity gives the curve shape on an induction logging tool in crossing the interface. The addition of auxiliary coils to achieve focusing can add anomalous character to the curve shape in crossing the interface, which might be mistaken for lithological detail. Preliminary calculations which include the propagation effects in the determination of the conductivity correction for thin beds lead to correction factors which are substantially smaller than those obtained from geometric factor considerations. It is apparent that thin-bed corrections derived from geometric factor calculations are of doubtful validity. INTRODUCTION Although the electromagnetic induction type of electrical well log has been used for a number of years and has gained general acceptance in quantitative well-log interpretation, no technically complete investigation of the mechanism and of its operation has been published. The studies which have been presented are based upon the premise that neither the shape nor the intensity of the induction field of the logging tool is in any way affected by the electrical characteristics of the formation. From the inception of induction logging it has been recognized that under some formation conditions the performance of the instrument could be expected to be substantially different from that predicted by the simplified analysis. This anomalous performance has been called "skin effect" since it is the result of the same phenomenon which causes high-frequency alternating currents to flow only near the surface of metallic conductors. In the range of conductivities encountered in the sediments, the formation actually does not exhibit the sharply defined conducting "skin" shown by metals. The gradual modification of the distribution of the currents in the formation, produced by the induction field of the logging tool, is the direct result of phenomena associated with the propagation of the electromagnetic field through the formation. Therefore, it can be much more appropriately described as the "propagation effect". One purpose of this paper is to review the results of a solution of the equations for the performance of a single transmitter-receiver coil pair induction-logging system which takes into account the propagation effect, showing the manner in which the tool performance established by this analysis differs from that derived from the less comprehensive analyses currently in use. PRINCIPLE OF OPERATION OF THE INDUCTION LOGGING INSTRUMENT The high-frequency alternating current which is maintained at a constant value in the transmitter coil

By G. D. Just

INTRODUCTION Large scale underground mining involves the bulk handling of fragmented material. The cost and efficiency of the mining systems is there- fore significantly influenced by material flow characteristics. Flow problems may occur in the form of ore pass blockages which interrupt the free flow at extraction openings. The costs of such delays can be readily assessed and compared to the costs incurred in reducing blockages by improved fragmentation or larger ore passes. In practice the problem is more complex than this statement suggests because it is generally un- economic to design for zero ore blockages. Another major flow problem occurs in the form of relative movement of ore and waste as the fragmented material is extracted. This produces waste dilution in the recovered ore and influences total ore recovery. This flow problem is much more complex than the ore block- age phenomena. Many questions concerning the precise flow characteristics remain unanswered because of the variability of size distributions, particle shapes, material properties and the total extraction layout and design. Model studies can provide a visual and quantitative illustration of probable flow characteristics but full scale data collection is necessary to evaluate the precision of such information. The methods and types of data obtained must be carefully selected to recover the maximum volume of useful information for operational control and future design. It is essential that honest precision levels are assigned to the data and any subsequent analyses. Grade control data may give misleading short term information on flow characteristics because of the difficulty in knowing the true grade of the mass of material before extraction commences. However, in the long term control of extraction grades is vital to the profitable operation of the mining system. The most efficient extraction design and operational schedule can only be determined after all of the facts and variables are known. This is usually only possible after the orebody has been completely extracted. However, if design and operational personnel have a full appreciation of the nature and variability of material flow under different conditions the best possible results should be achieved. The most significant features of material flow are out- lined in this paper in order to provide mine planning and mine management personnel with some of the necessary information relating to material flow. Available facts and reliable figures from selected publications are noted in association with unbiased and hopefully accurate opinions of the relevance of the data to mine design and mine system control. Possible future developments and profitable areas for research into material flow problems are also detailed. MATERIAL FLOW AND MINING METHODS The effects of material flow on the design and operation of an integrated underground ore handling system is one factor which is common to most mining methods. Analysis of the system as detailed by Just, 1980, permits the identification of unit process objectives. For example, a typical underground ore handling system as illustrated in Figure 1, involves the following unit operations:- (i) Gravity flow of ore in stope (ii) Ore extraction at base of stope (iii) Ore haulage on the production level (iv) Dumping of ore into ore pass system (v) Gravity flow of ore in the ore pass (vi) Underground crushing of ore (vii) Haulage of crushed ore to shaft (viii) Hoisting of ore to the surface. Average flow rates in each of these unit operations can be misleading due to variability in incremental capacity caused by flow blockages and machine delays. Thus to effectively analyse the probable performance of the system, it is necessary to have a measure of the flow loading and haulage rate variability. Mechanical equipment performance specifications can be used to provide such information for loading, haulage and crushing; however, in the case of the gravity flow of material field measurements are required to relate the probability of "hang-ups" to the degree of fragmentation. Factors affecting the frequency of flow stoppages are, size, distribution and cohesiveness of broken material and the geometry and size of the flow channel. Ore pass channel design is relatively simple since regular cross-sectional shapes are used

Jan 1, 1981

By W. F. Rogers, J. A. Stewart, P. J. Kalish, E. O. Bennett

Detailed descriptions are given of materials, apparatus and the experimental procedure used to study the effect of bacteria on sandstone permeability. The factors affecting permeability during injection of bacterial suspensions which have been investigated are: (I) concentration of bacteria; (2) core permeability and median pore size; (3) species of bacteria, mode of aggregation and relative size; (4) injection rate or pressure differential; (5) mean pressure; and (6) depth of penetration of bacteria. The investigation demonstrated that bacteria cannot reduce core pertneability to zero and that their effect on permeability is subject to definite limitations. Remedial or permeability restoration studies also were made. Acidization in combination with reverse flow war found to be an effective method for restoring permeability In cores partially plugged with bacteria. The relationship between the bacterial quantities in the laboratory tests and those found in field operations is discussed. The linear laboratory flow data have been translated into terms of field radial systems; these data indicate the most practical methods of maintaining injection rates in the presence of bacteria are to increase injection pressures or hydraulically fracture the formation. INTRODUCTION It has long been known that various bacteria flourish in the above-ground components of oil field water-injection systems. The presence of these bacteria has led to the suspicion that they might enter into the causes for reduction of injection well permeability, but only recently has an attempt been made to describe the effects quantitatively.1 Biocides are used in many cases without a firm knowledge as to whether the bacteria are killed, or if they are, whether the dead cells affect formation permeability. This project was undertaken as part of a study to determine the effect of bacteria, residual oil and precipitated solids such as iron sulfide or calcium carbonate on the permeability of sandstones and to learn whether any of these materials adversely affect brine injectivity in secondary recovery or disposal operations. This report deals with that portion relating to the effect of bacteria. MATERIALS CORES Three different permeability ranges of Berea sandstone cores were used in the study. The range of initial, absolute brine permeabilities kj were: high — 278 to 400 md: medium—130 to 162 md; and low—17.7 to 48.3 md. The permeability data for the cores used in the tests are included in Table 1. All cores were cut to a nominal 1 in. diameter. Following air permeability determinations, they were molded with an epoxy resin in 1.5 in. ID aluminum sleeves. The sleeves had drilled and tapped holes for intermediate pressure connections along the length of the cores. After molding, the high- and medium-permeability cores were trimmed to 4 in. in length and the low-permeability cores to 2 in. These lengths resulted in pore volumes of approximately 10.9, 10.4 and 4.4 ml, respectively, for the high-, medium- and low-permeability cores. Pressure-transmitting channels were drilled through the plastic into the core proper, using the sleeve holes as drill guides. Width and depth of channel penetration into the core proper were approximately 0.03 in. and 0.05 in., respectively. Three pressure taps were used with all cores; for the high- and medium-permeability cores the taps were spaced 1 in. apart; for the low-permeability cores the taps were spaced 0.4, 0.8 and 1.2 in. from the inlet end. Pore size distributions were calculated from restored-state capillary pressure curves for representative cores in each of the three permeability ranges. In each case the pore size range with the greatest percentage of the pore space included the very small pores up to 0.5 micron in radius. The median pore radii were in the 5.5 to 6 micron range for the high-permeability cores; in the 4.5 to 5 micron range for the medium-permeability cores; and in the 3.5 to 4 micron range for the low-permeability cores.

Jan 1, 1965

By W. F. Hosford, E. W. Kelley

Deformation studies have been conducted at room temperature on single crystals of magnesium and magnesium alloys with thorium and with lithium. Single crystals oriented to suppress shear on the easily activated basal slip systems were deformed by plane-strain compression. Compression along the C axis was accommodated by {1011} banding. Compression perpendicular to the unconstrained c axis activated {1012} twinning, and, after virtually complete twinning, deformation continued by {1011) banding in the twinned material. Compression perpendicular to the constrained c axis was accommodated by the simultaneous operation of (1012) twinning against the constraint and (1011 ) banding. Although this orientation was favorable for {1010)(1210) prism and {1011}(1~10) pyramidal slip, these modes were not observed in pure magnesium or in Mg-0.5 pct Th. However, {10i0)(1~10) prism slip was observed in crystals of Mg-4 pct Li during compression perpendicular to the constrained c axis. Fracture in all materials occurred parallel to (1124) or {l~il) depending on the orientation and composition of the specimen. THE mechanical behavior of the hcp metals is strongly anisotropic. Although several slip systems have been reported the slip is cpmmonly in the directions of closest packing, the (1210),' and this does not produce strains parallel to the c axis. Hence the inherent anisotropy. The deformation mode most easily activated in magnesium at room temperature is (0001)(1210)- basal slip. Also {1010}(1~10) prism slip and {1011)(1210) pyramidal slip have been reported, primarily at elevated temperatures.2"4 However, at room temperature the shear stresses to activate the prism and pyramidal modes are roughly a hundredfold greater than that required for basal slip.'j4 Thus prism and pyramidal slip may be expected only under special conditions of loading. Strains normal to the basal plane can be produced by twinning, however. Many twinning modes have been reported for magnesium,' with (1012) twinning the most common and relatively easy to activate. Magnesium can deform by (1012) twinning when stressed along the c axis jn tension, but not in compression. In contrast, (1011) twinning is activated by compression along the c axis and not by tension. In addition to primary twinning, secondary twinning or slip can occur within the reoriented material of primary twins.' In general at least five independent shear systems must be active to bring about an arbitrary shape change such as that in the individual grains of a deforming polycrystalline material.' Because basal slip can_ provide only two independent shear systems and (1012) twinning can only accommodate an extension of the c axis, other deformation modes must be active in magnesium for an arbitrary shape change to occur. The purpose of this investigation has therefore been to study the various deformation modes in magnesium at room temperature, with special emphasis on those modes that are less easily activated. The effect of the alloying elements, thorium and lithium, has also been investigated. In polycrystalline aggregates, unambiguous identification of deformation modes is extremely difficult and the direct evaluation of the resolved shear stresses to activate them is not feasible. On the other hand, uni-axial tension and compression experiments on single crystals may not activate some of the- deformation modes because basal slip and/or {1012) twinning cannot be suppressed in most orientations. However, it should be possible to activate all possible deformation modes using oriented single crystals and plane-strain compression. Identification of active deformation systems and evaluation of the resolved shear stresses required to activate them should be facilitated. Wonsiewicz and Backofen have recently completed an investigation of the plasticity of pure magnesium crystals at various temperatures utilizing plane-strain compression and selected crystal orientations. This technique has also been used in the present work. The seven orientations selected for study are indicated in Table I. Plane-strain compression along the c axis (orientations A and B) should activate some deformation mode _other than basal, prism, or pyramidal slip, or (1012) twinning. In orientations C and D, prism or pyramidal slip would be expected to take place. When the compressive load is applied perpendicular to an unconstrained c axis (orientations E and F) the three slip modes should be suppressed but not (10i2) twinning. In orientation G, basal slip should occur.

Jan 1, 1969

[TWEEDY, A. M., and VOGEL, FELIX A.: The Briquetting of Flue Dust in the United States by the Schumacher Process, XLVII, [viii], 338. TWEEDY, GEORGE A., and BEALS, ROGER L.: Cyanide-Plant and Practice at the Minas del Tajo, Rosan'o, Sinaha, Mez., XLI, [xl], 324. Twin Falls plant, Peninsular Power Co., LI, 298. Twins, deformation lies in manganese steel, LI, 882. 2,000-Ton Leaching Plant at Anaconda (LAIST and ALDRICH) (With Discussion), LV, [xxiii], 866.]

Jan 1, 1918

NEW MEMBERS The following list comprises the names of those persons who became members during the period Sept. 10 to Oct. 10, 1914: Members ALLEN, MILTON A., Min. Engr., Alaska Gastineau Mining Co., Juneau, Alaska. ALLPORT, ROBESON H., Gent Supt Colonial Coal & Coke Co., Dorchester, Va. ALSDORF, FREDERICK C.... Murray Apartments, 1026 Orange St., Los Angeles, Cal. ANDERSON, CARL A., Min. Engr 920 Wooward Ave., Portland, Ore. ARMS, CHARLES SEELYE, Asst. Met Willys-Overland Co., Toledo, Ohio. BAILEY, PHILIP P., Min. Engr McGill University, Montreal, Canada. BECK, CHARLES SMITH, Engr Detroit Copper Co., Morenci, Ariz. BEESON, ALEXANDER G., Chief Engr., Pittsburg-Buffalo Co. and Four States" Coal & Coke Co., Washington, Pa. BINGHAM, RAYMOND A Box 173, Bridgeport, W. Va. BJORGE, Guy N., Geol., Old Dominion Copper Mining & Smelting Co.,. Globe, Ariz.

Jan 11, 1914

By C. W. Vaupell

THE Huitzuco mines lie in north central Guerrero, Mexico; production has been about 90,000 flasks of quicksilver since 1873. Near-surface ores fill extinct mud geysers and the deep deposits are chambered veins, stock-works in brecciated blocks, and replacements in limestone. The epigenetic minerals livingstonite, stibnite and sulphur occur in limestone, gypsum and dolomite through a developed vertical range of 260 meters. The deepest workings expose an increased amount of stibnite, which probably indicates that the lower limit of mercury mineralization is being approached. A resur-gence of heat and water formed geysers over an extended area after the period of mercury mineralization. Mud geysers, which are situated, in the outcrops, contain the secondary mercury minerals, cinnabar and barcenite in the gravel and mud filling the vents. A 150-ton flotation plant is in operation concentrating stope fills that assay 3.0 kg. of mercury per ton. In one open stope, which is more than one hectare in area and 60 m. high, 150,000 tons are available.

Jan 1, 1937

By Samuel D. Warriner

The dealings between concentrated capital invested in the conduct of our various industries and the combinations of labor known as "trade union organizations," have produced not only in the United States, but abroad, many novel methods of negotiation between employers and wage-workers. The size and strength of these organizations have destroyed the personal elements formerly governing the dealings between employer and employee, and have produced various forms of trade-agreements now in more or less successful operation. The difficulty, however, has been to secure consent of both parties to an equitable agreement. For this purpose there have been devised various forms of arbitration, either compulsory under the shadow of governmental legislation, or voluntary by mutual agreement. But these have not been altogether successful from a technical stand-point, for the reason that a compromise has generally been necessary, and in an effort to reach an agreement, terms have been made which have been neither fair nor satisfactory to either of the contending parties. The Anthracite Board of Conciliation represents one of the few thoroughly successful courts for the settlement of trade-disputes, if not the only one which has yet been evolved. The prestige of this board rests upon its successful treatment of the labor-troubles of the anthracite region for a period of more than eight years, and upon the fact that it has been able

Jan 1, 1912

By Eugene W. Pearson

In a marked departure from conventional practice, the Power Plate process combines the two unit operations of leaching and electrowinning into a single continuous step for direct recovery of copper from sulfide concentrates, cement copper, copper scrap, and copper oxide slurries. Considering how environmental controls are pre- venting development of smelters for additional capacity or new construction, the Power Plate process provides a welcome pollution-free alternative to the smelting-electrorefining routes. And its low capital investment and low operating costs also recommend it to copper producers who are now using or investigating various hydrometallurgical methods.

Jan 12, 1974