Search Documents

By N. H. Fisher

GEOGRAPHICAL DISTRIBUTION THE most important known deposits in Australia of what are commonly referred to as the beach-sand minerals are along the most easterly part of the Australian coast, between Southport, 17 miles north of the Queensland-New South Wales border, and Ballina, 50 miles south of the border, and most of the production has come from this area (Fig 1). Smaller deposits are known to occur farther to the south at intervals for several hundred miles, and beaches have been worked at Yamba, 96 miles south and Woolgoolga, 150 miles south of the border and at Swansea, 60 miles north of Sydney. Important deposits have been shown to exist on north Stradbroke Island and others have been located farther to the north, as far as Tin Can Bay at the south end of Frazer Island. (Fig 2). Table I gives the list of operators with the location of their deposits and workings, their approximate maximum monthly capacity expressed in tons of heavy mineral produced by their concentrating plants before separation into individual mineral concentrates, their methods of mining and concentrating the minerals, and the products obtained. This table applies as of June 1948, but all the operators are remodeling or improving their plants and plant practices will be modified accordingly. In addition, active boring campaigns have been carried out by Alluvial Gold, Ltd., of Sydney, in the Cudgen-Cudgera area, and by Zinc Corporation. Ltd., of Melbourne, on Stradbroke Island, and in other places. PHYSIOGRAPHY Submergence of the order of 100 to 200 ft at the close of the Pleistocene period left the pre-existing hills as promontories and the valleys as deep inlets. Wave action has built bay-bars and sandspits in a northerly direction from the headlands, and lakes and marshes have formed between these bars and the initial post-submergence coast line. These lakes and swamps have been or are being filled in by river-borne sediments or wind-blown sand. Beasley1 has presented evidence that suggests a recent emergence of the coast line of about 10 ft. The evidence for this belief is the presence of a black sand seam 1/3 mile inland and 17 ft above sea level (Fig 3), and although it is not entirely certain that this seam is of beach formation and owes nothing to windblown concentration, other evidence supports the suggestion of recent emergence. Such emergence would undoubtedly aid the formation of bars and sandspits and the easterly progress of the beach front, leaving a series of parallel dunes (Fig 4). This belt of north-south coastal dunes ranges up to 1/2 mile in width and as many as 15 lines of dune have been counted (Fig 3). The foredune is generally the highest, up to 25 ft high, and there is in many places a flat platform in front of the dune known as the berm. The dunes behind the foredune are lower and less well defined

Jan 1, 1947

By J. M. McKenzie

p-n junctions to detect and measure the energy of single quanta of electromagnetic radiation are described. Useful energy range is from 1 kev to several Meu. Achieved energy resolution varies from 30 pct at 6 keu to 0.12 pct at 2 Mev. Parameters affecting the perfornzance of the present detectors and desired of a new material are discussed. DURING the last 6 years semiconductor detectors have been used extensively to detect and to measure the energy of charged particles. These detectors are made from reverse-biased p-n junctions. Electron-hole pairs are created in the depletion region of the junction, Fig. 1. The carriers are separated by the electric field and give rise to a pulse of current in the external circuit. This current pulse is proportional to the number of carriers and hence to the energy deposited in the depletion region by the ionizing event. More recently the discovery of the lithium drift process, first in silicon' and then in germanium,2 has extended the use of semiconductor detectors to the detection and the energy measurement of single quanta of electromagnetic radiation. These detectors now have a useful measurement range extending from the soft X-ray region, about 6 kev, to the hard y ray region of several Mev. Surface-contoured avalanche diodes can be used to extend this range down to 1 kev. There is however a desire for other materials suited to higher operating temperatures, and particularly for those materials with high y ray stopping power. The most important advantage of the semiconductor detector over gaseous and scintillation detectors is the average energy, E, required to form an electron-hole pair. Fig. 2 shows the quantum efficiency for germanium as a function of photon energy.3 At the band-gap energy, 0.7 ev, an electron-hole pair is generated by the absorption of the photon and the quantum efficiency is unity. The quantum efficiency remains constant at unity between 0.7 and 3 ev. It then increases as additional electron-hole pairs are formed by secondary ionization of the initial photoelectron. The rate of increase is about 1 electron-hole pair per 3 ev (actually 2.9 ev for germanium and 3.6 ev for silicon). This figure is constant irrespective of the particle type (electron, proton, a particle, heavy ion) and energy. In an ionizing event an incident particle of energy E will create N = E/e ion pairs. The statistical fluctuation in this number is proportional to &. The fractional energy resolution is therefore proportional

Jan 1, 1968

By W. B. Gogarty

With the use of polymer solutions in secondary recovery operations, the need has developed to understand the mobility control mechanism. This study investigated mobility control by considering both permeability and rheological effects. Experiments used a high molecular weight, partially hydrolyzed polyacrylamide polymer. Flow studies took place in reservoir and Berea cores having zero oil saturation. Effective size of the polymer flow unit was inferred from Nuclepore filter tests. Clay studies indicated the particle size capable of decreasing the core permeability. Flushed permeabilities measured the approximate core permeabilities with flowing polymer solutions. These permeabilities were considerably lower than original values. With mobility data and the flushed permeability, maximum effective viscosities were determined for polymer solution flow in a core. Effective viscosities showed that rheological properties play an important part in mobility control with polymer solutions. The study showed that permeabilities decrease and stabilize with polymer flow. At the lower permeabilities, high shear rates exist in the cores. Because of the pseudoplastic character of the polymer solution, the high shear rates caused low effective viscosities. This condition pointed to the inefficient use of the potentially high viscosity of the polymer solution at low shear rates. INTRODUCTION In the oil industry, a great deal of interest is being shown in the use of polymer solutions for secondary recovery and a number of polymer floods are being performed in the United States.1 Some of these floods have become commercial while others have been reported as failures. A number of floods are still in progress and remain to be evaluated. With the advent of polymer flooding, the need developed to understand the mobility control mechanism in porous media. Rheologically, the polymer solutions behave as pseudoplastic fluids. Investigators have studied the rheology for this type of non-Newtonian fluid in porous media?-6 Results have also been reported on the ability of polymer solutions to decrease mobility.7-10 Some investigators indicated that polymer solutions show a different rheological behavior in cores than on the viscometer.7,8 This study is representative of an initiatory investigation on mobility control with polymer solutions. Some effects are considered on a qualitative basis. Mobility control is considered from the standpoint of both permeability and rheology and, to the extent possible, permeability and rheological effects are considered separately. Results show that mobility control occurs from a reduced permeability caused by polymer retention and an effective viscosity determined by the average shear rate in the core. In this respect, rheological behavior is as important in mobility control as permeability. PROCEDURES A high molecular weight, partially hydrolyzed, polyacrylamide polymer was used in the investigation. Solutions of various concentrations were made with this polymer in different types of water. Some solutions used distilled water and others used tap water. The tap water contained approximately 500 ppm dissolved solids. As used in this paper, concentrations in ppm refer to parts by weight solute to one million parts by weight of solvent. In the tap water, calcium and magnesium accounted for from 60 to 80 ppm of the solids, the remainder being mostly sodium chloride. All solutions contained a bactericide, and anti-oxidants and antiprecipitants were added to the tap water. Capillary and concentric-cylinder* viscometers determined the rheological properties of solutions. The capillary viscometer is described elsewhere.6 Berea and reservoir sandstone were used as core materials for this investigation. Cores were 1 in. in diameter by approximately 2 to 3 in. long. Prior to mounting, the Berea cores were heat-treated for 3 hours at 850F. This treatment decreased the water-sensitivity of the clays in the cores. The reservoir cores were cleaned with solvent and

By T. M. Geffen, H. N. Hall

One-third to one-half of the original oil is left in most reservoirs even after thorough gas driving or waterflooding. In contrast, essentially all of the oil contacted con be recovered by flooding with a solvent (a fluid miscible with the reservoir oil). It is not economical to fill a reservoir with solvent since the value of the solvent would very likely exceed that of the oil. A practical method would be to inject a small bank of solvent to displace the oil. This solvent bank in turn could be driven through the rock by a less valuable scavenging fluid, such as natural gas which is also miscible with the solvent. Such a method of oil recovery was studied in the laboratory using long (up to 95 ft) core systems. It was found that, as the solvent moves through the reservoir, the front end of the solvent bank becomes mixed with the oil and forms a relatively short mixing zone between undiluted crude oil and pure solvent. An engineering correlation was obtained which can be used to predict the length of this zone. Displacement of the solvent by natural gas can be achieved with complete miscibility (above the critical pressure of the gas-solvent system at reservoir temperature) or with partial miscibility at lower pressures. Under conditions of complete miscibility, it was found that the length of the gas-solvent mixing zone could be predicted from the correlation developed for the solvent-oil mixing zone. With partial miscibility, two phases exist and the solvent is displaced by a modified gas drive in which vaporization and condensation occur. Equations are developed to predict the performance of this type of displacement. Two plans are suggested for application of miscible fluid displacement. one for miscible displacement of the solvent and the other applying to lower pressures where partial miscibility occurs during solvent displacement. Calculations based on the laboratory tests indicated that a bank of solvent with a volume of less than 10 per cent of the hydrocarbon volume under consideration will generally be adequate to obtain high oil recovery from the portion of the reservoir contacted in miscible fluid displacement. INTRODUCTION The conventional methods by which oil is displaced from reservoir rock—solution gas drive, conventional gas drive, and waterflooding—are all processes in which the oil is expelled from the rock by direct displacement with a fluid immiscible with the oil. Because of the immiscible type displacement, complete recovery of the reservoir oil is not achieved. In economically successful flooding operations, as much as 50 per cent of the original oil may be abandoned in the reservoir as unrecoverable. The use of a solvent (miscible with oil, such as LPG) as an injection fluid does not have the undesirable displacement features common to the use of gas or water (immiscible with oil). It can be readily appreciated, however, that it would not be economically feasible to displace the oil and entirely replace it with a solvent. A process was therefore devised for use in field operations in which only a small volume of solvent would be required to obtain essentially complete oil recovery in the portion of the reservoir contacted. In this process, the solvent acts as a buffer between the reservoir oil and injected gas, allowing the natural gas to displace indirectly the oil with much greater efficiency than if the gas displaced the oil directly. DESCRIPTION OF OIL RECOVERY PROCESS The solvent oil recovery process will be described in

Jan 1, 1958

By L. R. Mabson, F. M. Russell

INRODUCTION Roan Consolidated Mines Limited (RCM) operates five underground mines - Mufulira, Luanshya, Baluba, Chambeshi and Chibuluma (figure 1) . Associated metallurgical plants provide for the operations of milling, smelting two refineries for copper and a cobalt plant. Primarily a producer of high quality copper (242,000 tonnes during 1980) the Company is also the world's second largest producer of cobalt metal. RCM's remaining ore reserves at 31st March 1980 were 275 million tonnes at 2.84% copper. Monthly ore production is in excess of 1.2 million tonnes. Sublevel open stoping was the choice of mining method for the first underground operations on the Copperbelt for ore with dips steeper than 30 degrees. This was for use at the Roan Antelope mine, subsequently to be called Luanshya mine. The sublevel open stoping system was planned based on the methods used in many of the iron mines of Michigan and New York and in the copper mines of Tennessee. Peterson (Ref. 1) gave the following reasons for employing sublevel stoping, reasons which are still valid today: (1) the working place could always be barred and made safe, and the sublevel exit was always at hand; (2) the working conditions were similar day by day and drilling operations were repetitive; (3) pillar spacing can be varied as conditions demand; and (4) stoping operations could be shut down completely or opened up to full capacity at short notice, without affecting grade or causing wastage of reserves. Such was the success of the method that it was adopted as the basic mining method at all the RCM mines in their initial stages. Although cut and fill, block caving, and sub- level caving methods have been used, sublevel open stoping in its many variants still accounts for nearly 90% of total ore production in the Company. The following descriptions outline some of the applications of sublevel open stoping within RCM. LUANSHYA Geology There are two main ore deposits at Luanshya: the Roan (Luanshya Mining Area), in which mining began in 1930, and Baluba, in which mining production started in 1973 (figure 2). Both orebodies occur in synclinal and variably folded basins. These basins are underlain and completely surrounded by much older schists and granites. The ore formation, an argillite, lies near the base of the sediments and is underlain by conglomerates, quartzites and arkoses. Copper mineralisation is mainly found in two well defined zones, separated by a varying thickness of pyrite mineralisation. In the eastern part of the Roan deposit only the upper orebody is present, but west of 18 shaft and at Baluba the lower orebody predominates. Locally the subjacent quartzites of the footwall formation are also mineralised with copper. The copper mineralisation is found princi- pally as disseminated sulphides, mainly chalcocite, bornite and chalcopyrite. Near the surface the sulphides have been changed to oxides. At Baluba the cobalt mineral carrollite is found with the sulphides. Mining methods Sublevel open stoping is the basic mining method. In its standard form this method is best suited to steeply inclined orebodies, with simple structures and with a strong foot- wall and hangingwall. In recent years, as more complex folding and flatter dipping orebodies have been encountered, considerable variations have been introduced. Stope drilling is effected with drifters and extension steel.

Jan 1, 1981

By Jack White, Ralph B. Adair

THE Mufulira mine in Northern Rhodesia is 13° south of the Equator and at an altitude of 4100 ft above sea level. The concentrator was planned in 1930 to treat about 10,000 tons of ore per day, but before construction work had gone very far the size of the plant was reduced to 1500 tons daily capacity. Then just as the construction was finished in December 1931, the price of copper did not warrant the commencement of operations and it was not until October 1933 that the mine re-opened. Extensions have been made to the plant in 1034, 1935, 1936 1937, 1940 and finally in 1945. The capacity of the plant when the 1945 extension is completed will be 9500 short tons per day. The various extensions have been carried out with the minimum confusion and with great skill on the part of the designers and the erection engineers. In dealing with the plant in this paper it is proposed to give an outline of the present practice and only to refer to past practice when it is considered of particular interest. ORE TREATED The ore consists of fine grained highly siliceous, felspathic and argillaceous quartzites, the latter containing graphitic carbon and locally termed graywacke. These rocks are considerably altered near the surface and on the fringes of the ore body. Despite extensive efforts at mixing, both underground and in the crushing plant, many sudden changes of ore take place in the mill feed. The minerals are chalcocite, bornite and chalcopyrite with relatively unimportant amounts of malachite, native copper, azurite, covellite and chrysocolla. Gold is present at about 1 oz to a thousand tons, and silver at about 2 dwt. per ton. With increasing depth the nonsulphide content or, as commonly termed locally, the oxide content of the ore is decreasing and is now less than 0.25 pct against a high of 0.77 pct. CRUSHING OPERATIONS The first stage of crushing is done underground where the oversize from 12-in. grizzleys is fed to a 56 X 72-in. jaw crusher. At the Selkirk shaft two 10-ton skips deliver the run of mine ore at a rate of 450 tons per hour to the 400-ton capacity shaft bins. One 6 ft wide Ross chain feeder and one locally made air-operated finger feeder feed the two 30-in. McCully crushers. Ahead of each crusher is a 6 X 9-ft spring grizzley spaced at 5 in. on a 35° slope. Neither the Ross chain feeder nor the finger feeder is entirely satisfactory and for the wet, muddy and sticky ore that has to be handled it is planned to replace these with two 6-ft wide apron pan feeders. The McCully crushers deliver a minus 5-in. product, at a rate of over 500 tons per

Jan 1, 1947

By B. Zondek, W. T. Cardwell, J. W. Sheldon

The fundamental equations that are used to describe two-phase fluid flow in porous media are Darcy's law for each phase and an equation of continuity for each component. The special case of one-dimensional, incompressible, two-phase flow has received much attention in the petroleum engineering literature.1-10 The basic paper on the subject is that of Buckley and Leverett.2 Buckley and Leverett showed that one could eliminate the pressure and obtain a single partial differential equation for the saturation. They solved this equation for the case when gravity and capillary forces are negligible. A frequently encountered property of the solution of the basic partial differential equation is that, as time progresses, the saturation becomes a multiple-valued function of the distance coordinate, x. Buckley and Leverett interpreted the formation of multiple values as an indication that the saturation-distance curve had be-come discontinuous. They developed a method of determining the position of the discontinuity from a material balance. We solve the Buckley-Leverett partial differential equation using the method of characteristics and the concept of shocks. Our treatment is analogous to treatments used in the theory of supersonic compressible flow." Although the numerical results obtained are the same as those obtained by previous methods, we believe that this approach is more logical and has broader applicability. It can, for example, be generalized to treat the case when the fluids are compressible. It is not clear how one would go about doing this using the method of Buckley and Leverett. To illustrate the power of the method of characteristics with shocks, we solve a problem in gravity segregation which has not been treated previously in the literature. A special case of the general method developed here was used by Welge, to solve a particular fluid displacement problem. We consider two-phase incompressible flow along the vertical direction x in a porous medium. We assume that there is no flow transverse to .x. We measure positive in the upward direction. The fundamental equations are obtained from Darcy's law and the mass conservation law. Since the two phases are incompressible, mass conservation is equivalent to volume conservation.

By D. S. Eppelsheimer, D. N. Williams

The cold rolled textures of iodide titanium and of three samples of commercial titanium were examined using the Schulz-Decker Geiger counter technique. The iodide titanium and two of the three samples of commercial titanium showed a (0001) [1010] texture rotated 30' toward the transverse direction about an axis in the rolling direction. The third sample of commercial titanium showed a double texture. THE metals of the hexagonal system tend to deform similarly if the c/a ratios are similar. Thus titanium, zirconium, and beryllium, with c/a ratios of 1.601, 1.590, and 1.570, respectively,l should have similar cold rolled textures. The cold rolled texture of high purity iodide titanium has been described as (0001) [1010] rotated 30" toward the transverse direction about an axis in the rolling direction.' The texture of zirconium has also been reported as (0001) [1010] with a transverse rotation from the ideal position of approximately 30" about an axis in the rolling direction." This texture differs from that reported for titanium however since a continuous spread of (0001) poles toward the transverse direction was reported rather than distinct (0001) maxima 30" from the rolling plane normal. Beryllium has a texture similar to that of zirconium although the angle of transverse rotation of the (0001) poles is much less.' These three metals thus show a common type of cold rolled texture, as yet unexplained, which can be described as (0001) [1010] with various degrees of rotation toward the transverse direction about an axis in the rolling direction. Since titanium showed the greatest degree of rotation from the (0001) [1010] position, the cold rolled texture of titanium was re-examined using a semiquantitative Geiger counter X-ray technique to obtain more accurate experimental data from which a theoretical interpretation of this new type of hex- agonal rolling texture could be developed. The cold rolled textures of iodide titanium and of three samples of commercial titanium were determined. Table 1 gives the analyses of the titanium samples. Experimental Procedure Preparation of Samples: Prior to the final rolling operation each of the samples was given an initial reduction of approximately 50 pct and annealed to remove the gross effects of any previous treatments. Samples were annealed in vacuum, high purity helium, and air to determine whether annealing atmosphere had any effect on the cold rolled textures developed. All samples were annealed 1 hr at 800°C. Grain size determinations were made using the formula, 1.075 in which n is the number of grains counted in an area A (in sq mm) and M is the magnification of the area counted.' This formula gives the diameter between opposite flats assuming hexagonal grains. At least three areas containing more than sixty grains each were counted in each grain size determination. Rockwell B hardness readings were made on the annealed samples. The results of the measurements of

Jan 1, 1954

By R. F. Decker, J. R. Mihalisin

Phase transformations in a series of relatively pure nickel-titanium-aluminum binary and ternary alloys were studied. The purpose was to clarify age-hardening mechanisms, especially in predominantly titanium-hardened compositions. The micro-structures, as determined on a tirne-temperature-transformation basis by light and electron microscopy and X-ray diffraction, were correlated with room temperature and hot hardnesses. The stability of the ? phase under nonequilibrium conditions was shown to be important in this system. MANY of the alloys designed for service in the temperature range of 1200oF (649°C) to 1800°F (980°C) are austenitic iron-.nickel base alloys hardened by titanium and aluminum. The control of high-temperature properties of these alloys has been advanced by the knowledge of microstructures provided by the equilibrium diagrams of Taylor and Floyd1 and Taylor.2, 3 However, there have been notable instances in the predominantly titanium-hardened alloys where the correlation of properties with microstructure and the equilibrium diagrams has been unsuccessful. Mihalisin and carrol14 have noted in electron microscope studies of commercial alloys of this type that a fee phase precipitates and transforms to 71 (hep Ni3Ti) in stress-rupture tests. Bieber5 found that this fee phase remained in nickel-chromium-titanium alloys even when aluminum was excluded. Age hardening in iron-nickel base alloys has been attributed to 71 by Craver, Aggen, and Dyrkacz,6 ? (fee phase based on Ni3Al) by Beattie and Hagel7 and both phases by Lena,8 Yet, on the basis of the nickel-titanium-aluminum equilibrium diagram of Taylor and Floyd shown in Fig. 1, it has been difficult to understand the presence of ? in low aluminum alloys. Furthermore, the characteristic coarse dispersion of 71 has not been commensurate with the marked aging response. Also there have been anomalous grain boundary transformations in the iron-nickel base alloys which have markedly reduced notched stress rupture properties.9 These have been related to boron content and residual cold work. Recently, Golubtsova and Mashkovich,10 Buckle and Manene11 and Bogaryatskii and Tyapkin12 have noted a transition fee Ni3Ti in titanium-hardened nickel-base alloys. It was apparent from the latter studies that a transition phase was important in the nickel-titanium-aluminum system. The purpose of this study was to identify this phase, measure its transformation characteristics and kinetics, and attempt to correlate these findings with age hardening. It was believed that time-temperature-transformation studies, because of their adaptability to transition phases, would be of most value for this investigation. Accordingly, this method of study was undertaken on relatively pure nickel-titanium-aluminum alloys with controlled variations in boron content and residual cold work. EXPERIMENTAL PROCEDURES Compositions were selected from the nickel-titanium-aluminum isothermal section of Taylor and Floyd.' These compositions are plotted in Fig. 1 and were selected to obtain equal aging potential of approximately 15 pet by volume of the equilibrium precipitate. The materials were vacuum melted from

Jan 1, 1961

By M. J. Sinnott, J. C. Tobin

A technique for collecting and analyzing the small quantities of gases desorbed on heating metal powders has been developed. The gases collected from copper powders of various types of manufacture have been analyzed and found to contain H2O, CO2, and SO2. The quantities of gas evolved vary from 0.05 to 1.0 milliliter, under standard con-ditons of temperature and pressure, per gram of powder. The source of the gas has been traced to surface films on the powder. IN the powder-metal industry it is recognized that the presence of gases in the powders affects the processing and resulting properties of the sintered product. Several sources for these gases are possible; namely, chemical reactions with the sintering atmospheres, inclusion. of gases during compacting, dissolved gases in the metal powder, and sorbed gases on the metal-,powder surfaces.1, 2, 3 Since the quantities of the gases are relatively small, no direct attempt has been made to collect and analyze them nor to isolate their source. The work that has been done has been concerned with the dimensional stability of the product., its porosity, density, or mechanical and physical properties. Conclusions are drawn on the basis of studies of this type as to the probable effect of gases on these properties. 4, 5, 0 In the present investigation an attempt has been made to obtain quantitative data on the analysis and quantities of gases associated with copper powders manufactured in different ways. Apparatus was constructed to collect gases evolved from loosely packed powder samples on heating to various temperatures under a reduced pressure of helium. The powders were outgassed thoroughly in a vacuum prior to starting the collection operation in order to eliminate mechanically entrapped gases and to prevent the possible reaction of the powder with these gases. Experimental Procedures Materials—The major portion of the investigation was carried out on a single heat of water-atomized, oxygen-free, high-conductivity copper. A relatively coarse fraction of this powder, 20 to 100 mesh, was tested as a mixed powder and as various graded size fractions. The microstructure of this powder showed equiaxed grains and was clean and free from oxides and oxide eutectic. The particle size, as determined

Jan 1, 1959

By Louis P. Gignac

INTRODUCTION The selection of trackless equipment for underground mining can be a complex engineering problem due to the wide range of equipment sizes and operating modes. Computer simulation is particularly useful in estimating the performance of different systems for specific rock- handling problems. A hybrid simulator, incorporating some of the features of deterministic and stochastic simulation, was developed in order to handle not only queuing delays at loading and dumping points, but a1 so traffic interferences. Any number of vehicles can operate in any one of four basic modes (LHD, LAF, FEL, HFC) in parallel or in series. If the units use common roadways, loading and dumping points, certain operating delays will occur and be registered by the simulator and thus give a better evaluation of the marginal productivity of each additional unit. Based on a typical layout of drawpoints and ore passes for the sub-level stoping method, productivity and operating costs of different rock-handling systems will be examined. 1 . COMPUTER SIMULATION Numerous applications of computer simulations are reported in the 1iterature for various mining problems. Depending on the complexity of the system to be studied, simulation models were conceived with different degrees of sophistication. Three different types of simulators are generally recognized: stochastic, deterministic, and hybrid. Stochastic or Monte Carl o simulation randomly generates items, transactions, or events from some population defined by a frequency distribution and produces some expected future situations. Because this type of simulation is governed by the input of probability distributions, it requires a detailed knowledge of the system to be simulated; it implies expensive and time-consuming studies and reports to gene- rate this input information. A major short- coming of stochastic techniques is in new equipment evaluation, where the lack of data is unavoidable, and in new system design where the conditions are outside the range of the known historical behavior of the equipment. However, probabilistic simulation is almost essential for the study of cyclic queues and traffic problems. Deterministic simulation studies a system by generating performances on the basis of the mechanical capabilities of the vehicles and the physical limitations of the mining scheme. It is based on the engineering principle that the engine converts its energy into a rimpull at the wheels, which is in turn opposed by the rolling resistance and the grade of the ground; the machine is accelerated or decelerated until the tractive and resistive forces are in equilibrium, at which point it moves at constant speed. The information required by this technique, such as rimpull charts and equipment weight, is readily available from equipment suppliers. However, equipment performance at the mining site is also dictated by human and environmental conditions and changes with time and usage. For this reason, deterministic simulation generally overestimates the system capabilities; these must then be adjusted by efficiency factors based on observation and experience. Recently, hybrid simulation models, using both stochastic and deterministic techniques, have been built with some of the events generated stochasticly and others being deterministic. This compromising approach originated at the Pennsylvania State University. O'Nei1 (1966) designed a simulator for truck-and- shovel operations that allows for transportation from multiple faces to mu1tiple destinations. Each truck performs according to its mechanical capabilities while its loading and dumping time and its load fluctuate according to specific probability distributions. A major advance in the simulation of mining systems is due to Sanford's model (1969) of underground coal mining operations. The originality of the model is in the use of an Executive System Control which sets up the initial system, de- fines the operation conditions , and instructs continuously four sub-assemblies representing shuttle cars, trains, continuous miners , and conveyors, which in turn generate a feed-back of their movement to the Executive Control System for further instructions. The model has enough flexibility to simulate simultaneous and sequential jobs that characterize any dynamic system. Sanford's early work evolved slowly to what is known today as the Under- ground Materials Handling Simulator for coal mining (Manula, 1974).

Jan 1, 1981

By John Wulff, J. H. Hollomon

The opinion has been widely held that the corrosion of alpha brass occurs by the selective solution of zinc. As late as 1939, Fink1 and Evans2 suggested that in the initial stage of the corrosion the selective solution of zinc produces copper-rich areas, which subsequently act as cathodes that facilitate the deposition of copper. Previously Abrams3 had shown that most of the copper found on corroded brass was re-deposited and not residual, although he did not consider the nature of the initiation of the corrosion process. Enough data exist to indicate that any metal surface is sufficiently heterogeneous to provide the anodes and cathodes necessary for the initiation of corrosion.4,5 Thus, for alpha brass we need postulate not an initial selective solution of zinc, but only the existence of local differences in electrochemical potential. The heterogeneity responsible for potential differences may arise from oxide and other films as well as from alloy concentration gradients. Even though selective corrosion may be possible in some alloy systems, previous data on alpha brass as well as the experimental work reported in this paper do not require this supposition. Bengough and May16 in a discussion of Abrams' paper, first suggested the addition of small amounts of arsenic (0.03 per cent) to a1pha brass to prevent the redeposition of copper (dezincification). This suggestion was later substantiated by Nixon.7 In their studies of the inhibiting influence of arsenic, Evans and Fink were led to the selective-solution hypothesis in order to explain the initial corrosion of such alloys. They believed that an arsenic film covered anode areas and prevented the formation of copper-rich spots capable of acting as cathodes for the deposition of copper. They did not consider, however, the mechanism by which the arsenical film was formed. Bengough and May,a in another publication, suggested that the commonly found gray or black arsenical film may act to: (I) carry oxygen to the brass surface, (2) increase the discharge potential of copper on brass, (3) precipitate cuprous chloride from colloidal suspension in chloride solutions. Masing9 assumed that the film found upon arsenical brass was metallic arsenic. His measurements of hydrogen overvoltage of bulk arsenic led him to believe that the inhibition of dezincification occurs because the overvoltage of a brass surface is lowered by the arsenic film. He reasoned that this film would permit the more rapid reduction of hydrogen at the cathode, which would prevent the redeposition of copper. In a recent paper,10 we have pointed out that the film formed during the corrosion of arsenical brass and copper in stagnant solutions is essentially arsenious oxide (As2O3),

Jan 1, 1942

By H. S. Greismer

Alabama washes a larger percentage of its total coal output than any state in the Union. For producing coking coal, three-compartment jigs are favored; mines providing, steam and commercial coal use single-compartment jigs exclusively. Chemists are as necessary to washing plants as recording gages are to power plants. Experiments in Alabama indicate that the sludge released by coal-washing plants can be deposited in streams and on agricultural lands without disastrous results. CAMPBELL, 1 in 1896 said: "The Birmingham district in Alabama has certain great advantages for there are few places in the world where fuel and ore are so near together, although, unfortunately, both are of inferior quality; the ore being low in iron and high in phosphorus and the coal giving a weak and impure coke." This statement could not have been, questioned in 1894, but by 1896 several Robinson-Ramsay washers had been put into operation and weak and impure coke was a thing of the past. The Warrior coal field of Alabama contains six seams that yield coking coal of excellent quality. In descending- order, they are Brookwood, Milldale, Pratt, America, Mary Lee, and Black Creek. In each of these, however, bands of rock and bone coal of varying thickness are stratified with the coal; and while some of these impurities can be separated from the coal by the miner, much of it must be loaded out with the coal: Consequently, unless the coal is washed before being coked, it will yield a coke of varying ash and sulfur content quite unsatisfactory, for blast-furnace use. At present, the Gulf States Steel Co. is producing run-of-mine coal at its Virginia mine, from the America seam, that is uniformly low enough in ash to permit of coking without washing, but this is the only exception to the above statement. Alabama was the first state to experiment seriously with coal washers, was the first to install washers on a large scale and, up to the present, has maintained the lead. The Alabama State Mine Inspector reports that during 1923 20,919,303 tons of bituminous coal were mined in Alabama; 12,858,499 tons of which were delivered to coal washers for treatment.

Jan 9, 1924

By Marie L. V. Gayler

Without diffusion taking place in liquid metals and alloys, no castings could be made; it is therefore the most important factor affecting the structure of metals. Diffusion involves the interchange of atoms, a process which takes place during the life history of an ingot. In the liquid, atoms are in a state of high thermal agitation, but this thermal vibration is reduced in amplitude with falling temperature. When solidification sets in, the atoms arrange themselves on an ordered space lattice and the changes in structure which take place in the solid are due to the interchange of atoms on this space lattice. The rate of atomic interchange—e.g., of diffusion—is most rapid at temperatures close to the melting point and decelerates as the temperature is lowered. At room temperature, the rate of diffusion is practically negligible in most alloys, and any change in structure can only be brought about by using methods which will accelerate the rate of diffusion. The rate of diffusion depends on three factors (I) temperature; (2) concentration gradient and (3) activation energy. The growth of grains and particles in the solid alloy also depend on these factors and are therefore intimately associated with diffusion. The rate of homogenization in a cast alloy depends on several factors, such as: (I) rate of solidification, which involves grain and particle size which, in their turn, depend on diffusion: (2) the nature of the constituents; (3) the temperature interval between the melting point of the metal or alloy and the temperature at which it is being heat-treated. It is well known that coarse, cast structures are extremely difficult—if possible— to homogenize, and the finer the grain size and particle size, the more readily solid solution will take place. The rate of diffusion depends, also, largely on the nature of the constituents; for instance, copper and magnesium form solid solutions with aluminum quite readily but nickel and iron do not; neither do certain intermetallic compounds, such as alpha and beta FeSi. Furthermore, the actual formation of intermetallic compounds may be a very slow process, particularly when they are formed in the solid state as equilibrium products. For example, BFeSi is formed in the solid as the result of the reaction aFeSi + A1 —+ PFeSi. The particles of aFeSi become surrounded with a reaction ring of PFeSi. This layer is formed as the result of diffusion of atoms taking place between the aluminum matrix and aFeSi. As the amount of aFeSi surrounding the core of aFeSi increases the concentration gradient becomes low and so the rate of diffusion of atoms also decreases until it practically ceases. This occurs after a comparatively thin layer of ßFeSi has been formed. It follows that when intermetallic compounds of this type are formed in the solid, as the result of diffusion, it is generally impossible ever to attain equilibrium, since the forma-

Jan 1, 1944

By C. S. Barrett

It has been observed that deformation in iron takes place by slip on (110) + {112) + (123) planesl, 2, but in silicon ferrite with low deformation temperatures or high silicon contents (exceeding 4 per cent) the authors have found that slip is confined wholly to (110) planes, at least with small amounts of deformation. The purpose of the present investigation was to determine the effect of this alteration of slip mechanism on preferred orientations in cold-rolled and recrystallized strips. Incidental observations on the effect of the recrystallization temperature were also made. The numerous determinations of the texture of cold-rolled iron and steel have been in satisfactory agreement as to the principal features of the texture (with the exception of a few conclusions that apparently have been based on insufficient data). The texture is chiefly one in which 11101 directions of the grains lie along the direction of rolling, with a deviation of a few degrees, and in which the (100) planes lie in the plane of the rolled sheet, with a deviation from this position chiefly about the rolling direction as an axis. This deviation about the rolling direction as an axis has been measured by different observers and lies between about 45" and 50" or 60" for iron5, 6, 9 and is usually in the neighborhood of 50" for mild stee16, 7, 8. The range of this deviation is a function of the percentage of total reduction8, 10. Post8 reported that it decreases with increasing percentage reduction, but apparently he studied only the surface material, which Gensamer and Meh17 found to be somewhat differently oriented from the material in the inside of the sheet. McLachlan and Davey10 found that the deviation also decreases with increasing percentage of total reduction for the material in the interior of the sheet and is independent of the percentage of reduction per pass. The deviation about the cross direction as an axis (the direction in the

Jan 1, 1937

By Marie L. V. Gayler

Without diffusion taking place in liquid metals and alloys, no castings could be made; it is therefore the most important factor affecting the structure of metals. Diffusion involves the interchange of atoms, a process which takes place during the life history of an ingot. In the liquid, atoms are in a state of high thermal agitation, but this thermal vibration is reduced in amplitude with falling temperature. When solidification sets in, the atoms arrange themselves on an ordered space lattice and the changes in structure which take place in the solid are due to the interchange of atoms on this space lattice. The rate of atomic interchange—e.g., of diffusion—is most rapid at temperatures close to the melting point and decelerates as the temperature is lowered. At room temperature, the rate of diffusion is practically negligible in most alloys, and any change in structure can only be brought about by using methods which will accelerate the rate of diffusion. The rate of diffusion depends on three factors (I) temperature; (2) concentration gradient and (3) activation energy. The growth of grains and particles in the solid alloy also depend on these factors and are therefore intimately associated with diffusion. The rate of homogenization in a cast alloy depends on several factors, such as: (I) rate of solidification, which involves grain and particle size which, in their turn, depend on diffusion: (2) the nature of the constituents; (3) the temperature interval between the melting point of the metal or alloy and the temperature at which it is being heat-treated. It is well known that coarse, cast structures are extremely difficult—if possible— to homogenize, and the finer the grain size and particle size, the more readily solid solution will take place. The rate of diffusion depends, also, largely on the nature of the constituents; for instance, copper and magnesium form solid solutions with aluminum quite readily but nickel and iron do not; neither do certain intermetallic compounds, such as alpha and beta FeSi. Furthermore, the actual formation of intermetallic compounds may be a very slow process, particularly when they are formed in the solid state as equilibrium products. For example, BFeSi is formed in the solid as the result of the reaction aFeSi + A1 —+ PFeSi. The particles of aFeSi become surrounded with a reaction ring of PFeSi. This layer is formed as the result of diffusion of atoms taking place between the aluminum matrix and aFeSi. As the amount of aFeSi surrounding the core of aFeSi increases the concentration gradient becomes low and so the rate of diffusion of atoms also decreases until it practically ceases. This occurs after a comparatively thin layer of ßFeSi has been formed. It follows that when intermetallic compounds of this type are formed in the solid, as the result of diffusion, it is generally impossible ever to attain equilibrium, since the forma-

Jan 1, 1944

By J. W. Halley, G. L. Plimpton

Because of the two distinct stages in the solidification of rimmed steel, segregation in the rimmed ingot is more complex than that in the killed or semikilled ingot. In the earlier stage, chemical reactions, resulting in evolution of gas and vigorous stirring of the metal, effect a degree of negative segregation unique to rimmed steel. The composition of this zone constitutes the principal quality advantage of this type of steel. In the later stage of solidification, after the evolution of gas has ceased, the segregation follows the general pattern of a more completely deoxidized steel. However, the composition of the liquid remaining after the first solidification stage varies markedly from that of the original melt, some constituents having been partially removed as reaction products while the concentration of others has been intensified by rejection from the metal solidifying in the first zone. The aim, from the standpoint of segregation, in rimmed steel of high quality is to effect a maximum negative segregation in the rim zone without excessive concentration of undesirable elements at the center of the ingot. To achieve this aim, the composition of the melt may be varied and the furnace and pouring practice may be adjusted within certain limits. It is the purpose of this study to discuss segregation in rimmed steel from the standpoint of the mechanisms that produce it and to survey the phases of open-hearth practice that influence those mechanisms. Mechanisms Producing Segregation The mechanisms that determine the degree of segregation in the rimmed ingot are closely interrelated, making it difficult to select the primary factors and to determine a satisfactory order for presenting them. For instance, the question of sulphur segregation is relatively simple, since sulphur is not directly involved in chemical reactions in the ingot; but its concentration in the rim zone is dependent not only on its original analysis in the melt, its segregation coefficient, and the freezing rate, but also on the rate of its removal from the impure film on the solidifying surface. This washing action involves all the factors (such as freezing rate, the carbon-oxygen product, pressure, etc.) that determine the rate of gas evolution and hence the efficiency of film removal. Sulphur distribution between the rim and core is affected by the volumetric ratio between the two zones, and its segregation in the core is a function not only of the freezing rate of the core but also of all the foregoing factors that determine its concentration in the metal when solidification of the core starts. To simplify the presentation, it is proposed to treat the mechanisms affecting segregation independently in this section, reserving a discussion of their over-all effects for the section in which actual segregation data are given. The factors affecting segregation will be treated in the following order: (I) differential solidification, (2) removal of constituents as

Jan 1, 1945

By C. F. Floe, N. J. Grant, A. Joukainen

A CCORDING to Guertler,¹ Smith and Hamilton were the first to study the Cu-Ti alloy system, but because of the presence of large amounts of impurities their data are inconclusive. Hensel and Larsen² in 1930 and Kroll³ in 1931 determined the high copper end of the diagram. In 1939 Laves and Wallbaum,4 in a short summary of compound determinations in titanium binary alloys, mentioned the existence of a face-centered cubic compound, Ti2Cu, with 96 atoms per unit cell, and also a compound, TiCu3, which was said to have a deformed hexagonal close-packed structure in which ordering had been observed. The existence of a compound, TiCu, was also found but the crystal structure was not determined. Craighead, Simmons, and Eastwood determined the effect of copper on the allotropic transformation in titanium. The investigation was limited to alloys containing from 0 to 5 pct Cu, using titanium of fairly high impurity content. Experimental Procedure The methods used for determination of the diagram included metallographic examination and X-ray and thermal analyses. The system was first worked out using the higher purity "Process A" sponge titanium and oxygen-free copper. The high titanium region was next determined more accurately using iodide titanium and vacuum-melted, oxygen-free copper. Preparation of Alloys: The alloys were prepared by arc melting under prepurified helium atmos- pheres in water-cooled copper crucibles. The high purity iodide titanium alloys were prepared by melting three compositions along with a specimen of unalloyed titanium in a single charge. A multiple crucible was used which consisted of a copper plate with four cup-like depressions. The unalloyed titanium was melted first and acted as a getter for any oxygen and nitrogen in the melting chamber. Since these elements harden titanium, the hardness of the standard specimen was an index of the highest probable contamination of the alloy melts. The sponge titanium alloy melts weighed from 100 to 200 g each and the iodide titanium melts from 20 to 25 g. In order to insure greater homogeneity most of the alloys were melted, turned, and remelted twice. The larger buttons made from sponge titanium were sectioned or crushed before remelting. These alloys up to 30 pct Cu were further homogenized by forging at 925°C. They forged readily up to 20 pct Cu but numerous cracks were formed in the alloys containing from 20 to 30 pct. Above 30 pct Cu the sponge titanium alloys were homogenized by heating for 200 hr at 850°C under prepurified helium. Similarly, the iodide-grade titanium alloys containing up to 3 pct Cu were homogenized at 1000°C for 24 hr and all others at 880°C for 200 hr.

Jan 1, 1953

By C. H. Mathewson

ABOUT fifty pages of Henry M. Howe's profound treatise, "The Metallography of Steel and Cast Iron," are devoted to twinning with special reference to the origin, nature and general significance of the Neumann bands in ferrite. Howe believed with Osmond and Cartaud1 that the Neumanns are mechanical twins and his careful observations leave no doubt that these straight-sided narrow bands habitually occur parallel to trapezohedral planes of form {211}. Attempt's to develop the structure of the bands by various methods so that their identity could be established beyond question have not been conspicuously successful. Howe thought that they deflected slip bands. Some of the etching figures which have been developed within and adjacent to Neumann bands support the contention that they are twins. A good example of this effect in ferrite containing 0.6 per cent. of nickel and 1.3 per cent. of phosphorus, originally due to Harnecker and Rassow,2 was reproduced in. the 1928 lecture before the Institute of Metals Division on twinning in metals.3 In this case, the sides of the figures might represent the traces of cubic planes laid bare by etching a properly oriented grain of ferrite, twinned along a plane of form {211}. Our own observations in this direction may be represented by Fig. 1 which shows in a deeply etched cavity in the boundary region between a Neumann band and the original crystal two small crystal surfaces which resemble the faces meeting at a reentrant angle in the simple cube twinned along a bisecting plane of form {211} as sketched in Fig. 2.

Jan 1, 1928

By R. A. Morse, W. O. Keller

The properties of limestone reservoir rocks such as the distribution and degree of continuity of the pore systems, and the relative volumes and permeabilities of the systems making up the complex cause large variations between performance of individual limestone reservoirs and their susceptibility to secondary recovery methods. The effects of these factors on the mechanism of fluid flow cannot be adequately evaluated with presently developed concepts, laboratory data, and geological information. The observance and interpretation of the performance of individual limestone reservoirs provides, at present, the most adequate approach for evaluating the integrated effects upon performance of the many. now immeasurable variations in the properties of limestone reservoirs. INTRODUCTION The development and application of techniques for increasing the efficiency of oil recovery from natural reservoirs is a problem of primary importance to the industry. During the past several years, a great deal of effort has been expended by the technical personnel of the industry toward the improvement of present known methods of oil recovery. and evaluating the factors which control the susceptibility of particular reservoir types to economic application of secondary recovery methods. Providing adequate and accurate laboratory data on the properties of the reservoir rock and its contained fluids. together with good production statistics, are available, methods have been evolved for estimating with reasonable accuracy the performance of an oil reservoir under either continued natural depletion or conditions imposed by introducing additional displacing fluid into the reservoir from an extraneous source through the injection of gas and/or water. The susceptibility of limestone reservoirs to secondary recovery by gas injection is very much dependent upon gas-oil relative permeability relationships for the reservoir in question. In a rock formation in which the porosity is of the intergranular type such as is found in sand stones and some non-fractured dolomites, a representative sample of the pore structure can be obtained in a small core plug. In this type of reservoir, it has been shown that relative permeability data obtained from laboratory experiments can be Properly applied to evaluate the flow relationships actually observed during the depletion of a reservoir. In addition, a good idea of the fraction of the reservoir which will be swept by the injected gas may be obtained from the spacing pattern used and the permeability profile of cored wells. From these data, it has been demonstrated that reliable estimates of performance and recoveries under gas injection operations can be made for reservoirs in which the Porosity is of the intergranular type. Limestone reservoirs on the other hand often present much more complex problems. One reason that the performance of limestone reservoirs is so variable is that there may be, in reality. two or more pore systems, the integrated performance of which will depend upon the physical properties of each system and their inter-relationship. For instance, in a limestone reservoir, the main pore structure, as far as void spaces for storage of hydrocarbons is concerned, may be represented by the intergranular openings of the rock. Usually in limes and dolomites, the intergranular pore openings are very small and the matrix permeabilities extremely low. Often, as in the case of Many dolomite and oolitic lime reservoirs, this is the only pore system, and performance is observed to be very similar to that of a sand stone of similar permeability. However, in the great majority of' the limestone reservoirs, there is present, in addition to the intergranular pore system, a complementary system of openings caused by fracturing or solution.',' The openings in the latter system are usually many times more permeable than the intergranular pore system due to their much larger size, and may contribute almost all the fluid carrying capacity of the formation, even though their volume may be a very small part of the total pore space in the reservoir. Obviously, the performance of such a complex under either primary or secondary control will deend upon the distribution and degree of continuity of both systems, the relative volumes and permeabilities of the

Jan 1, 1949