Search Documents

The object of crushing and grinding for leaching is obviously to permit contact of the solvent and mineral and subsequent removal of pregnant solution in a reasonable time. Heap leaching is the leaching of ores that have been mined and transported to prepared, relatively impervious pads for leaching by sprinkling or ponding, and percolation of the lixiviate through the ore. Dump leaching is the leaching of dumps or low-grade ore or overburden without the use of prepared pads under them. Run-of-mine material, e. g., low -grade ore from open pit stripping operations, may be leached without crushing, and a fairly high recovery made by heap leaching. An alternate method for better grade gold/silver ores is to crush to 9 to 13 mm (318 to112 in. ) size for pad heap leaching, as used by Smoky Valley Mining Company at Round Mountain, Nevada, on gold ore, and to 38 rnrn (1 -1 12 in.), which will be done by Candelaria Partners, at Candelaria, Nevada, on silver ore. Heap leaching of copper probably began at Rio Tinto, Spain, about the year 1752. This was done by the leaching of weathering piles of ore in the open air followed by iron cementation of the liquor that drained off the heaps. Its application to the low -grade southwestern United States copper ores was overlooked for many years, and low- grade ores from Sacramento Hill at Bisbee, Arizona, were the first to be heap leached in 1923. Site preparation used a half century ago is the same today. "The need for some form of waterproofing of the pad was evident. Before leaching ore was piled, the site was cleared of cactus and brush. After clearing a gentle sloping area, it was then covered with a blanket of rolled and tamped clay or slime tailing. When heaps are built, a layer of coarse fragments may be put down first to assist drainage. A second method of leaching without grinding, usually for higher grade ores, is by vat or tank leaching of material crushed to 9 to 13 mm (318 to 112 in.) size. Such a plant is considerably more expensive than a heap leaching installation but much less costly than grinding for agitation leaching, and a recovery higher than that obtained by heap leaching is to be expected. Vat leaching has been widely used by the copper industry on higher grade copper ores but has been used in only a few small operations on that size gold or silver ores. However, such a plant should be considered for a modest tonnage of a few million tons, 3 to 7 g per mt (0.10 to 0.20 oz per st), of Carlin-type leachable ores crushed to 9 mm (318 in.).

Jan 1, 1981

By Charles Fulton

This paper describes experiments carried on at the Case School of Applied Science, together with their results. Their success led to the design of the larger furnace herein described, but which has not been built. A PREVIOUS article' by the authors contained a general description of the new roasting furnace herein described but it did not go into detail as to the metallurgical behavior or the results obtained. Believing that such information would be of great value, they have elaborated on the subject and have given many unpublished details. The furnace described applies the principle of roasting finely divided zinc-sulfide ores, now produced in large quantity by the flotation process, in gaseous suspension; that is, the ore particles are carried, in suspension, in a current of air and gaseous products of the roast. The relatively great fineness of flotation concentrate presents difficulties and problems of roasting in furnaces of the ordinary type; the fine ore is forwarded through the furnace in the form of a shallow bed and its very fineness leads to dense impervious bedding which prevents oxygen from reaching the interior of the bed, thus unduly lengthening the time of roasting and preventing the elimination of the last of the sulfur. The fineness of the concentrate, normally, should lead to a rapid and complete roast, for the speed of roasting is a function of the surface exposed to oxygen, which surface is greatest, per unit of weight, in very fine material. The difficulty in bed roasting is to get the oxygen to the particle. If the fine ore, during the roasting, could be freely suspended in oxidizing gases, full advantage could be taken of the great surface conferred by its fineness. This fundamental idea, of course, is not new, for the Stedtefelt furnace, familiar to the older metallurgists, is an example of it; but the manner in which this is accomplished may be new.

Jan 10, 1924

By M. Gangal, B. Paul

It may be seen from Maurer's survey (Maurer,l 1966) that most of the common methods used in rock drilling today depend upon mechanical loading of the rock. In order to predict the behavior of rock under an imposed system of stresses, it is necessary to have a valid criterion which delineates those combinations of stress which cause macroscopic rock failure from those which do not. Admittedly, the conditions under which brittle materials fracture depend very much upon statistically variable local effects such as inclusions, grain boundaries, minute imperfections, etc. However, it is extremely desirable to be able to predict fracture under complex states of stress by means of a stress-criterion of failure, where, for a given material, the effects of the other variables mentioned are incorporated into a small number of experimentally observable parameters. One of the most successful of these "macroscopic stress criteria" has been the Coulomb-Mohr theory 2,3 (also see Jaeger 4 and Terzaghi 5), modified by the addition of tension cutoffs (Paul 6). At first thought it might seem rather odd that a macroscopic theory is capable of predicting fractures which originate at highly localized random imperfections at an atomic level (or more likely at the level of individual mineral grains in rocks). However, Griffith7 showed that fractures originating near the tips of randomly oriented elliptical cracks lead to the macroscopic stress criterion of failure indicated in Fig. 1 (a). Fig. I (a) is to be interpreted in the following way: P and Q represent the maxi mum and minimum principal stresses (compression is considered positive) in a macroscopically isotropic body; fracture will not occur for any combination of principal stresses lying within the 'fracture curve' shown, but

Jan 1, 1967

By J. W. R. Rayner

THE conventional method of making water gas involves individual plants for the separate carbonization of coal to coke and the subsequent gasification of coke with steam. The process demands lump coke, preferably made from the best quality of coking coals. The ash in the coke should have a high melting point and the gasification process suffers a loss of efficiency when cokes with law ash-melting points are used. In Britain, these coals are generally the most expensive and they are readily available only in certain localities. The coals not suitable for making lump coke, or yielding only poor quality coke, are much more widely available and are generally cheaper. DEVELOPMENT OF ALTERNATIVE PROCESSES In Germany, processes have been developed and operated commercially for the production of water gas from very low-rank coals such as brown coal and lignites, but much less effort has been spent on processes to use coals of intermediate rank, which are widely available in Britain. The brown-coal processes use coal in the form of either dust or briquettes. The most successful of the dust-gasification methods is the Winkler process, which made a substantial contribution to German oil production during the war. It uses coal in the site range 0 to 8 mm and the fuel bed is blown with a mixture of oxygen and steam at a rate high enough to give it a characteristic boiling motion or, in present-day phraseology, at a rate more than sufficient to fluidize it (Fig. 1). Air cannot be used to provide the heat required for gasification, for various reasons. In the first place, to make the process continuous by mixing air and steam would involve the production of a lean gas-containing much nitrogen. If a separate blow were used, a large amount of potential heat would be lost because the blow gas in such a process would contain a very high percentage of carbon monoxide. Oxygen is necessary therefore and oxygen remains relatively expensive for use in gasification. In the Winkler generator, formation of clinker caused by local overheating does not occur, because of the mobility and high heat transfer of a fluidized bed. These properties of fluidized dusts have been used most successfully

Jan 1, 1953

By Frederic K. Bunton

The smelting plant of the British Columbia Copper Co. at Greenwood, B. C., now closed because of the decline in the price of copper due.to the European war, is of special interest to metallurgists for several reasons. It was successfully smelting in blast furnaces the lowest grade copper ore of all plants in America. In order to do so, it had to run at very hig~; efficiency, which necessarily required a large tonnage per square foot of hearth area, together with the minimum amount of labor and other costs. The furnaces smelted daily 2,250 tons of ore (6.62 tons per sq. ft. of hearth area), carrying 0.85 per cent. of copper, at a smelting cost of 81.18 per ton. The entire plant required 130 men to operate it and keep up repairs, showing a labor efficiency of about 17.5 Dons per man per day. In the present paper, the method of obtaining these results is shown. Most of the information contained in this description I obtained as Assistant Superintendent, during the two years preceding the present shutdown. Other sources of information to which I am indebted are: The British Columbia Copper Co., Ltd., by ALfred W. G. Wilson, in The Copper Smelting Industry of Canada; Greenwood Smelting Worlrs, by J. E. McAllister, Engineering and Mining Journal, vol. xci, pp. 1011 to 1015 (May 20, 1911); and Description of the Copper Smelter of The British Columbia Copper Co., by W. L. Bell, in Transactions of the Canadian Mining Institute, vol. xvi, pp. 151 to 154 (1913). II. Location and Connections The smelter of this company is about half a mile south of GreenGood, in the Boundary district of British Columbia, on the Columbia & Westerg branch of the Canadian Pacific Railway. It was originally built in 1900 by Paul Johnson, to handle 600 tons of ore a day in two small furnaces of 300 tons capacity; but in 1907 the old furnaces were torn out, the plant was remodeled, and three blast furnaces, 48 by 240 in. at) the tuyéres, were installed. In 1910, two of these were enlarged to 51 by

Jan 1, 1916

By Lancaster Jones

The gravity magnitudes obtained by means of observations with the Eötvös balance in the field are necessarily resultant or total effects due to all abnormalities of mass distribution, including even the effects due to the ellipticity and rotational motion of the whole earth. Since the object of the survey is to isolate the effects which arise solely from some particular subterranean feature, and to deduce therefrom the configuration and extent of this feature, the first step is to eliminate from the observed effects all those due to "disturbing" (i. e., unwanted) features, whether above or below the surface of the ground. The disturbing features have different characteristics, according to their situation relative to the center of the balance and to the horizontal plane through the foot of the balance, or station point; this diversity was recognized by Eotvos, who divided the total effects into so-called Normal, Terrain, Topographical, Cartographical and Subterranean effects. This classification has been adhered to by most subsequent investigators, but the writer prefers to employ the term "three-dimensional," which really indicates the essential character of the class of effect known as "Subterranean," at any rate from the standpoint of the computer of effects. Before disturbing effects can be eliminated, the features must be measured up or surveyed, whether by topographical, mining, or boring methods, and then the effects of each feature calculated and subtracted from the total observed effects. After this the problem of interpreting the residual effects will itself necessitate the computation of the assumed feature, or even a series of trial features. The task of computing gravity effects is therefore of great importance. In the early work, by Eötvös himself, the computation practically ceased when the terrain and topographical effects had been calculated, but later surveys have demanded an ever-increasing extension in the technique of computation. Certainly in surveys designed to locate minerals, particularly ores, the calculations have to be extended far beyond those of Eötvös, while his methods of computing both terrain

Jan 1, 1929

By Franz R. Dykstra, R. F. Tatnall

A ferroalloy is defined as: "An alloy of iron with some element other than carbon used as a vehicle for introducing such an element into the manufacture of steel. The element may alloy with the steel by solution or, as the carbide, -neutralize the harmful impurities, by combining with them and separating from the steel as flux or slag before solidification."a The most commonly used ferroalloys are: ferromanganese, ferrochrome, ferrosilicon, ferrovanadium, ferromolybdenum, ferronickel, ferrotungsten, ferrocolumbium, and ferrophosphorus. Concern here is with the sources and markets of the major metallic alloying elements. The discussion is further restricted to those - ferroalloy ores, the principal use of which is in the production of steel. Phosphorus, silicon, and tungsten, for example, are ferroalloys of some economic significance, but other uses dwarf their alloying applications. Thus, this discussion will deal with the ores of managanese, chromium, nickel, molybdenum, vanadium, and columbium. As shown in Table 14.1B.1 ferroalloys serve to- facilitate processing and impart to the finished steel such characteristics as tensile strength, ductility, low-temperature impact, hardenability, high-temperature strength, corrosion resistance, toughness, and abrasion resistance. In the steel-making process, ferroalloys may be added in the charge, in the molten bath near the end of the finishing period, in the ladle, or in the molds. Timing of the addition depends on the effect of the addition on the temperature of the molten metal, the formation and elimination of reaction products, and the protection of subsequent additions from oxidation. MANGANESE General Approximately 95% of the manganese ore sold is consumed by the steel industry, either as ferromanganese or as manganese metal. Manganese is the universal alloy, without which good steel cannot be made. It serves as a scavenger, removing phosphorus, sulfur and, to a degree, oxygen from the melt. As an alloying material it makes steel hard, tough, and resistant to wear. Approximately 6 kg of manganese is required for every ton of common steel produced by United States steelmaking practice. The remaining 5 % of the manganese ore consumed consists of special or so-called "chemical" ores, including high-grade pyrolusite ores, electrochemically reactive "battery ores," and a number of special varieties, as well as those otherwise regarded as "metallurgical ores."

Jan 1, 1976

By Boyd Dudley

The material presented in this paper is an abstract of a thesis submitted by the writer to the faculty of the Massachusetts Institute of Technology, as part requirement for the degree of Master of Science. The investigation was undertaken at the suggestion of Prof. H. 0. Hofman, and it was conducted, under his direction, in the laboratories of the Mining Department of the Institute. The purpose of the work was, first, to study some of the reactions that have been considered as a part of the mechanism of the chloridiz-ing roast, and second, to study the conditions under which nickel oxide and copper oxide may be chloridized. While the production of chlorine gas by various reactions during the chloridizing roast may not be primarily useful in the chloridation of metal oxides and compounds, it nevertheless serves a useful purpose in preventing the dissociation and decomposition of chlorides once they have been formed; for example, the dissociation of cupric chloride into cuprous chloride and chlorine. Therefore it was thought that a study of some chlorine-producing reactions would prove of interest, and the first series of experiments dealt with this phase of the subject. he object of the latter part of the work was to show the possibility of treating heavy sulphide ores, such as those of Sudbury, Ontario, containing much iron and small amounts of copper and nickel, by chloridizing and removing the copper, leaving an iron-nickel oxide product suitable for smelting in the blast furnace for nickel-bearing pig iron. The chloridizing of the copper would, of course, be preceded by a roast for the removal of sulphur, the sulphur oxides being available for the manufacture of sulphuric acid, if under the local conditions this product would be of commercial value. Reactions of the Chloridizing Roast Reaction of Sodium Chloride, Sulphur Trioxide, and Oxygen.—The first reaction studied was that involving the production of chlorine

Jan 1, 1915

By Paul M. Tyler

Fully a decade ago, demand for ground mica began to exceed supplies of scrap mica from manufacturing operations and of waste block from feldspar and sheet mica mining in the United States, with the result that in recent years the market has absorbed larger and larger quantities of mica recovered as a by-product from clay washing,1 as a joint product with kyanite12 and by grinding schists. So far, only schists that contain a large percentage of mica have been utilized for making ground mica, but already there has been a good deal of wishful thinking with regard to recovering mica as an aid to the prospective working of low-grade gold ores and ores of certain base metals. With wet-ground mica selling at $60 to $100 a ton and even dry-ground mica worth over $20 a ton, many ores that could not be considered as otherwise workable under present conditions will show commercial possibilities if they can be made to yield even a relatively small percentage of salable mica. An interesting paper might be written on the coming role of industrial minerals as joint products of metal mines. It is largely a matter of markets. Many years ago I watched the mess left behind the gold dredges in the mountains of Colorado and thought of the Denver sand and gravel operators who prided themselves upon their canniness in providing devices for catching gold merely as an incident to their regular business of selling what we miners classed as "tailings." Nowadays almost every milling or mining operation near settled communities finds use for at least part of its waste for road material or concrete aggregate and several eastern iron mines have gone into the crushed-stone business. Promoters now mention fertilizer "filler" as potentially salable at all the way from $1 to $10 a ton, or whatever is needed to cover costs of mining and treating the "ore" and leave the metal values as "clear profit." In emulating the pork packers in their efforts to utilize "everything but the squeal," mining engineers may go too far; on the other hand, they should not let

Jan 1, 1942

By J. S. Hardison

In the fall of 1912, the appearance of water in the oil of the Nevada Petroleum Co., Coalinga, Cal., made necessary the installation of a dehydrating plant to reduce the water below the 3 per cent. limit prescribed by the agency. Unlike the mining industry, technical literature of the oil industry is limited and extremely unsatisfactory. Until the recent efforts of the Petroleum and Gas Committee of the American Institute of Mining Engineers, no concerted movement has been instituted to secure publication of papers dealing with the problems of the oil business, and because of the additional fact that dehydrating of oil has not been practiced in California to any extent up to comparatively recent time, it was found necessary to experiment in order to determine the most satisfactory plan for this purpose. It is easy to write regarding successful enterprises, but, while not SO pleasant, it is equally desirable to write of failures so that others may be saved the loss incident to such investments. The water in this oil occurs both free and as an emulsion. Free water easily settles out, but the emulsion requires treatment. So far as can be determined, the emulsion consists of globules of water surrounded and enveloped by a film of oil. Starting with this hypothesis the theory has been evolved that in order to break up this emulsion the water must be heated at least to boiling point, when an explosion takes place destroying the globule. Unfortunately, this condition was not recognized in the installation of the first plant, which was planned on the following lines: A heater was arranged so that all the oil from the wells could be heated before reaching the shipping tanks, these being already fitted with coils for steam heating. Tanks were filled with about 4 ft. of water, live steam was turned into the coils and the water brought nearly to the boiling point, when the heated oil was run in. This for a time was partly successful, but the length of time necessary to apply this heat was too great for practical operating.

Jan 1, 1915

By Nelson Severinghaus

Consolidated Quarries Corp. must conduct operations for an average sales price of $1.25 per ton, about the same price at which stone was sold 25 years ago when the dollar was worth twice what it is now. To maintain success in a competitive business, the company must solve the usual production problems, which will be discussed here in the order they occur in the flowsheet. Most crushed stone quarries must first remove soil and decomposed rock. Although seasons of lower sales sometimes release regular quarry excavating and haulage equipment for this purpose, overburden is often too extensive for this method to be used. In such cases, special equipment must be assigned or the job may be contracted. As many earthmoving contractors have heavy duty specialized equipment well suited to overburden removal, they should be seriously considered before the job is undertaken. Pockets of clay beneath peaks of hard stone sometimes defy mechanized removal. Pick and shovel laborers at this point might be supplanted by more ingenious use of pumps and water or some other mechanical means. Where overburden is extremely heavy or difficult to remove, underground mining must be considered.

Mar 1, 1956

By R. E. Zimmerman

ALTHOUGH flotation of coal is considered relatively new in the United States by coal-preparation engineers, actually it has been practiced to some extent for the past 30 years, It is practiced much more widely in Europe than in the United States. Commercial plants are operating in nearly all major coal-producing countries of the world. A froth flotation plant has been operating since 1930 at the Champion No, 1 preparation plant of the Pittsburgh Coal Co. Unfortunately the term flotation is widely used in the United States by coal-preparation engineers to designate dense medium processes of coal cleaning. As used here, flotation means those processes for cleaning fine sizes of coal in which the coal is collected in a froth or matte at or near the surface of a pulp. The refuse particles remain in the pulp. Two distinct types of flotation are practiced: froth flotation and agglomeration. FORMS OF FLOTATION The theory of the principles of flotation and of the physicochemical foundations surrounding this process has become a complex and scientific field and coal-preparation engineers contemplating use of flotation processes would do well to study the works of Gaudin, 2, 5 Taggart, 3 Zimmerman, 4 Wark, 6 Ralston, 7 Petersen. 8 Bulk Oil Flotation.-In this process the separation of mineral from gangue is accomplished by virtue of the fact that minerals of metallic lustre, as sulphides, or hydrocarbons, as coal and graphite, are wetted preferentially by oil in the presence of water and consequently pass into the interface between oil and water; while gangue or rock is wetted by water and remains in the medium. Beginning in 1860 with Haynes and later between 1897 and 1907, at least 25 patents were granted for bulk oil flotation. Large quantities of oil are required, generally 3 to 25 per cent by weight of feed, and recovery of such oil is a major problem. The Elmore process 3 (1901 and 1902) is an example of a bulk oil process, The Trent process (1902-25) has been used for the cleaning of coal on a commercial scale, According to E. W, Davidson 9 there were five such plants operating in the United States by 1925. They have since been abandoned.

Jan 1, 1950

By L. W. Kesler

Kansas produced 41,966,773 bbl. of oil in the year 1927, thereby taking fourth place among the oil-producing states of the Union. The daily average production decreased from 121,609 bbl. in January to 110,244 bbl. in December. Due to excessive flush production and the resulting decline in the price of crude during the year, operations, both in proved and outlying districts, were reduced materially from those of 1926. There were 2338 completions in 1926, but only a total of 1333 in 1927. Regardless of this decrease in the total number of completions, Kansas made a slight gain in total production for the year, producing 620,262 bbl. more than in 1926. This is accounted for, in part, by the comparative long life of the settled production from the Bartlesville sand areas to the east of the Nemaha granite ridge, and by prolific production in eastern Summer County from horizons new in their importance in the state, productive here at two localities along the axis of the granite ridge (Table 1 and Figs. 1, 2 and 3.) For convenience in further consideration, the state is divided into Eastern and "Western" Kansas. Special emphasis will be placed on those areas in the state of which but little is generally known, and which have not been given detailed consideration in previous publications.

Jan 1, 1928

By T. A. Rickard

In a previous paper (ante, p. 411) some description was given of the occurrence of the auriferous alluvium, extensive deposits of which lie among the highlands of the province of Otago, New Zealand. The present paper will describe some of the methods by which that alluvium is exploited. The alluvial mining of New Zealand is not yet hindered by " debris legislation." The mines are for the most part situated in a country of little agricultural value, and large rivers with rapid currents act as tailings conveyors. In time, however, steps will have to be taken to restrict the discharge into the Clutha of the tailings which are slowly raising the river-bottom. The methods of California have been followed in Otago with such alterations as peculiar local conditions require. The distinctive feature of the alluvial mining of Otago is the prominence given to the hydraulic elevator. The all-important factor in this form of mining is the control of an abundant water-supply at a suitable height above the level where it is to be utilized; and in this respect the gold-fields of the south island of New Zealand are most favora-

Jan 1, 1893

By Henry S. Mackay

The interesting paper recently submitted by Messrs. Tobelmann and Potter1 shows that chemical problems have developed which are of great interest in this new and important branch of metallurgy. Those who realize what a process of this kind really involves will agree that it deserves a better name than '(leaching process." The word leaching conveys the idea that the copper is simply leached out of the ore with acid and then precipitated on iron; the chemistry of such a process would be of little interest. As, however, during the first year's operation of this plant 24,400,532 lb. (11,067,837 kg.) or about two-thirds of the produce, was electrolytic copper, while 7,992,033 lb., or about one-third, was cement copper, it would seem more appropriate to term the process electrochemical. It further appears, from the particulars given, that efforts have been made to have the entire production in the form of electrolytic copper. This could be done if the chemistry of the problem were kept in balance, so that it would not be necessary to discard any solutions that carried copper and acid of commercial value. A process, such as that under consideration, in which the copper is precipitated from solution by electrolysis, the solvent being at the same time regenerated, is one that requires special chemical and electrochemical knowledge and experience if all the copper in solution that has been extracted from the ore is to be successfully and economically produced as electrolytic copper. The object of this paper is to discuss, from the practical and theoretical standpoints, the chemical and electrochemical problems involved in the working of a process of this kind, and which must be solved to keep it in chemical and electrochemical equilibrium. In such a process, if the chemical balance is maintained, a solution can be used alternately as a solvent for the copper in the ore and as an electrolyte of high efficiency for the precipitation of the copper. To maintain the chemical equilibrium and so attain this result, the process must be so controlled that the solu-

Jan 1, 1921

By Richard H. Rein, John Chipman

The activity of SiO2, in the entire liquid system SiO2-CaO-Mg0-A12O3 at 1600°C is calculated from the distribution of silicon between these slags and Fe-Si-C alloys saturated with either graphite or silicon carbide, the activity coefficient of silicon in these alloys, and the requisite thermodynamic data. The activities of the other components in the ternary systems SiO2-CaO-A12O3, SiO2-MgO-CaO, SiO2-MgO -A12O3 are computed from these data by the IrON blast-furnace slags can be regarded as consisting of the four major oxide components, SO2, CaO, MgO, and A12O3 along with minor proportions of other oxides and of sulfur. The purpose of this study is to measure the activity of silica in the liquid solutions of these four oxides at iron-making Gibbs-Duhem equation with the aid of the known free energies of several of the interoxide compounds and the accepted phase diagrams. Based on these activities, new data are Presented for the free energy of formation of a number of the interoxide compounds. The free energy of mixing the liquid metasilicates of CaO and MgO shows slight positive deviations from the ideal. temperatures and to obtain activities of the other components by application of the Gibbs-Duhem equation and the properties of several interoxide compounds. Recent investigations on the activity of silica in the SiO2-CaO-A12O3 system1-3 and recogntion of a serious error in older data for the free energy of formation of SiO2 (Ref. 4) have succeeded in bringing a fair degree of concordance into the results of different investigators. In the present study, the activity of silica is obtained from the silicon-distribution experiments described in a previous paper,' the revised activity coefficient of silicon

Jan 1, 1965

By Donald Cummings

MEASURES appropriate for the control of the silicosis hazard in mining cannot be formulated precisely, but sufficient knowledge1-19 has accumu-lated during the past quarter century to permit the suggestion of useful, though partly empirical, rules for its alleviation. The industrial hygienist today recognizes that the peril incurred by the inhalation of harmful dust is a function of two variable factors-the degree of harmful exposure and the specific susceptibility of the exposed individual to pulmonary injury. Con-trol of the danger arising out of prolonged contact with pernicious air-borne particulate matter is consequently best exercised by influencing both of these recognized variables. Obviously the problem has two broad aspects-one, medical; the other within the province of the engineer.

Jan 1, 1938

By C. D. Hunter, I. B. Browning, N. W. Shiarella

During the year 1936 improvement in the oil industry in Kentucky continued at about the same rate as shown by that of the year 1935 over the year 1934. The development of several new pools in western Kentucky and the increase in the application of repressuring methods to the old fields of eastern and to a lesser extent of western Kentucky increased the total production to 5,481,227 bbl., as compared to 5,175,054 produced in 1935. The principle sources of this increased production are the Livermore field and the new Bates Knob field in McLean County, in western Kentucky, and the result of repressuring operations in the " Corniferous" pools of Lee, Powell, Wolfe, Morgan and Estill Counties and the "Weir" sand (of Mississippian age) fields of Magoffin, Lawrence and Johnson Counties in northeastern Kentucky. The last named fields have a producing sand especially adaptable to these methods. Drilling No new fields were opened in eastern Kentucky during the year. All new drilling was codned to pressure wells and new oil wells to complete patterns around the intake wells. Owing to the relatively low "initial" or flush production of the wells in this section—even though the ultimate recovery per acre is as large—higher prices for crude will have to prevail before extensive search for new fields is begun; as in northwestern Kentucky, where active exploratory work has been carried on as in the several preceding years, resulting in numerous new and prolific, although comparatively small fields. In this section approximately 500 new oil wells drilled in the Owensboro field, embracing several pools in Ohio, Hancock, Daviess, McLean, Henderson, Webster and Nuhlenberg Counties in the northwestern part of the state. The total oil production for this field during 1936 exceeded by many thousand barrels the 2,821,722 bbl. produced in 1935. In these fields the producing sands range from the middle Missis-

Jan 1, 1937

By J. D. Miller, M. Misra

The processing strategy for the effective separation of bitumen from low grade (<l0 weight percent bitumen) Utah tar sands by a hot water process differs significantly from that used for the processing of high grade (> 10 weight percent bitumen) Utah tar sands. Excellent separations (coefficient of separation = 0.9) can be achieved for high grade Utah tar sands by intense hot water digestion followed by a modified froth flotation step. Such a technique is ineffective for low grade tar sands. In order to change the characteristics of the low grade tar sand an attempt was made to enrich the bitumen content of the feed to greater than 10 weight percent by recycle of bitumen concentrate to the digestion stage. However, the quality of the separation was not improved under these circumstances. Similarly feed enrichment by heat treating the low grade feed with recycled concentrate prior to digestion did not improve the separation. More successful separations of low grade Utah tar sands were finally achieved by modification of the viscosity of the low grade bitumen with controlled addition of diluent. These results of the hot water separation tests and variations in the quality of separation are interpreted in terms of the physical properties of the bitumen and the surface bonding forces operative at the bitumen-sand interface.

Jan 1, 1981

By R. S. McCaffery, R. G. Stephenson

The statistical analysis of blast-furnace data was undertaken to determine some of the relations which exist between the variables involved in furnace operation, and particularly to show the effect of variation of slag composition on such economically important factors as coke consumption, daily tonnage of pig iron and sulfur elimination. It&apos; was desired to correlate the results obtained in commercial practice with those predicted from a study of the quaternary system lime-alumina-silica-magnesia. This paper presents the results of a preliminary study of blast-furnace daily operating reports, and is intended to indicate the suitability of our method of attack and something of the results that may be expected from an extended statistical examination of such data. It has been shown that blast-furnace slags are not composed of oxides, as reported by chemical analysis, but are actually composed of several compounds, each made up of two or more of the oxides present.&apos; These compounds persist in the liquid state, and the properties of a slag are the properties of a mixture of these compounds, and not of a mixture of the ultimate oxides. The oxides lime, alumina, silica and magnesia make up 94 to 96 per cent. of the usual blast-furnace slag, and assuming that we may neglect the remainder of the components, we may determine the minerals present, and their relative proportions, from a study of the quaternary system involving these four oxides. Operating reports from 15 furnaces were available for this investigation. Complete slag analyses for one slag per day were available, per-mittling the calculation of the mineral composition of the slags used. Basic, malleable and foundry irons, with silicon varying from 0.75 to 4.50 per cent. were included in the reports for this examination.

Jan 1, 1931