Search Documents

By Harold M. Mooney

RESISTIVITY measurements for determining depth to bedrock, water table, and other geologic discontinuities have had only limited success. Many of the difficulties can be attributed to complex geology and to basic limitations of the method; current flow through a continuous medium is a diffusion phenomenon, emphasizing irregularities near the source and smoothing out those at a distance. Some of the failures, however, are due to careless field work and incompetent interpretation. A forthcoming publication1 may help to reduce difficulties of this sort. The writer here attempts to bring order into the multiplicity of interpretation methods and, to a limited extent, to evaluate them. For all methods, the field data to be interpreted consist of apparent resistivity values plotted against electrode separation, Fig. 1. The interpretation should give depths to one or more geologic horizons. Direct currents and the Wenner four-electrode configuration will be assumed, since these are widely used, although the interpretation problems remain essentially the same for other electrode configurations. Alternating currents higher than, say, 20 cycles per second introduce complications beyond the scope of this paper. Three approaches to the interpretation problem have been used. These may be called empirical, theoretical curve matching, and direct. Many techniques have been proposed, but each can be reduced to one of these approaches and to a single geologic idealization. This idealization rests on the following assumption: the earth in the limited volume of interest can be approximated by a horizontal sequence of layers, each homogeneous and isotropic in its electrical properties. This seemingly restrictive assumption has proved to have practical value, although future work should aim at removing some

Jan 1, 1955

By Stephen Birch

THE Chitina mining district of Alaska is located at the headwaters of the Chitina and Copper Rivers. At present, the only producing min-ing properties are the mines of the Kennecott Copper Corpn. and the Mother Lode Coalition Co., which are situated 196 miles from Cordova the port of entry. The first claims, later acquired by the Kennecott Mines Co. and afterwards transferred to the Kennecott Copper Corpn., were discovered in 1900. The Copper River & Northwestern Ry., which connects the mines with tide water at Cordova, was completed in the spring of 1911. Contemporary with the construction of the railroad, aerial tram equipment was brought to the mines by pack train and a tramway, 3 miles, long, connecting Bonanza mine with the proposed railroad terminal, was finished, enabling shipments of high-grade ore to be made immediately on the completion of the railroad. A mill to treat the lower grade ore was begun the same year. The Kennecott company's holdings consist of 111 mineral claims. The Mother Lode Coalition Mines Co., which is controlled by the Kennecott Copper Corpn., owns 73 claims adjoining the Kennecott holdings. All data on operations and geology refer equally well to the Mother Lode property.

Jan 1, 1924

By Mark L. Requa

During the past two years California has developed a new and important oil-field: I refer to Midway. This field produced the famous Lake View gusher, which is credited with a total production in excess of 8,000,000 barrels. Fortunately for the oil industry of the State, this well is now a thing of the past, and nothing, save a great crater-like opening marks its location. The pipe is entirely worn away and gone; and it is a matter of serious doubt if there can be anything done that will cause the well to produce again. Fortunately, also, there have been no other wells in that field or elsewhere throughout the State that in any may compared with the Lake View. Midway is noted for large wells, of from 500 to 2,000 barrels production; but the decline is rapid, and a few months serve to bring the output down to a few hundred barrels. In the oil-territory heretofore blocked out as proved and probable, there have been, during the year, many changes. Some areas which were expected to be fairly productive have apparently failed; others, more strictly "wild-cat," have come in; while in some of the older fields there are properties which are beginning to shorn evident signs of exhaustion. The total area of proved territory will therefore probably suffer but small

Jan 1, 1912

I. THE ENERGY CRISIS STILL EXISTS A. ALTHOUGH IMMEDIATE SHORTAGE IS NOW ALLEVIATED BY: 1. Increased imports through lifting of Arabian embargo; a. Imports were 6.5 million bpd during the week ended January 17, or 1.3 million bpd higher than last year. b. 1.7 million bpd higher than March '74. 2. Decreased demand resulting from higher prices and conservation. a. January 1975 demand was 17.9 million bpd, 0.1 million bpd lower than January 1973 and … b. 2.0 million bpd, or 10% under originally projected demands for January 1975. c. Gasoline (excluding tax) went up 59% from 27d/gal in August 1973 to 43c/gal in September 1974. d. Gasoline demand for January 1975 was 6.3 million bpd, 0.1 million bpd higher than 1973 but 0.7 million bpd ( 10% ) under projected demand. 3. Increased crude and major product inventories. a. January 17, 1975 crude and major product inventory was 794 million bbl, 99 million bbl higher than the same date in 1973. b. 105 million bbl increase since April 12, compared to only 38 million bbl increase during the same period in 1973.

Jan 5, 1975

Uranium was the prima donna of 1978, and the exploration pace was fast and furious in traditional uranium producing areas such as the Powder River Basin, Grants mineral belt, San Juan Basin, and Uravan mineral belt. Adding fuel to the fire were several significant discoveries: The Date Creek Basin of western Arizona, the McDermitt caldera of northern Nevada, and Tallahassee Creek in Colorado's intermontane basin. Advances in solution mining haw resulted in deeper drilling on the Texas Coastal Plain, and the price of uranium has encouraged widespread exploration in frontier areas and non-sandstone environments.

Jan 5, 1979

By T. Egleston

FOR several years I have been engaged in studying the behavior of iron' and steel under varying conditions of tension and compression, as well as of shock and abrasion. Some of these observations have been communicated to the Institute at various times. Within the past year I have been looking at the various observations that I have made as a whole, and have been led to the conclusion that there is a regular law of fatigue and refreshment of metals, and that the change which produces either the fatigue or refreshment is a chemical one, which is, however, in almost all cases accompanied by physical and molecular changes at the same time. That metals under conditions that were more or less well understood became worthless, has been known for many years. It has been known to blacksmiths that iron and steel, when improperly treated in their fires, become "burned," as they call it, and could no longer be used, and some of them have had a scrap heap into which such material was thrown. A few of them knew that after a period more or less long the iron or steel recovered some of its original properties and could, with many precautions, again be used, but that these phenomena followed any law has not to my knowledge been announced. My attention was first attracted to the varying conditions under which iron and steel rails break in service. It was not long before I became convinced that there was a general law applicable to all metals which allowed of their being used with safety within certain limits, and caused their rupture when the use extended beyond these limits, and this law I have called the law of fatigue of metals. When we observe the causes of deterioration in iron and steel rails, we find that they are principally shocks, either slight and frequent, like those produced by the passing of a train over a road-bed in good order, which produces a vibration. sensible to the ear laid on the rail, for very long distances, but distinctly audible for only a short one; or from sudden and heavy blows, like the descent of the locomotive and each car successively from a high to a low rail. * Read at the Montreal Meeting, September, 1879.

Jan 1, 1880

By R. L. Templin

IN TREATING a cast metal by any working process such as rolling, drawing or forging, variations in the conditions present in the remelting, casting, chilling and preheating of the initial ingot will certainly have some effect on the physical properties of the final product. In considering the effects of cold working on the physical properties of metals, however, it will be assumed that these factors, being controlled according to best practice, will remain constant and therefore may be neglected. Starting with such a uniform metal ingot, the next operation in the production of wrought metal involves hot working by rolling, forging or extrusion so as to produce a slab, billet or bloom. This working must be sufficient to produce substantial grain refinement and minimize any defects occurring in the initial ingot. Even such a hot-worked product is not suitable as a starting material for determining the effects of cold working because it contains internal strains analogous to those resulting from cold working. It is necessary, therefore, to supplement the hot working with a considerable amount of cold working, followed by a proper annealing in order to obtain a material suitable for use in defining the effects of cold working on the physical properties of a metal. That is, if the effects of cold working are to be evaluated accurately it is necessary to have other effects at least constant if not absent. Such material, unfortunately, cannot always be obtained in commercial practice but the requirements just indicated certainly represent the desired goal; this goal has been attained in the treatment of some metals, one being aluminum.

Jan 1, 1929

By A. D. Hodges

The process to be described, whatever other merits (or demerits) it may have possessed, certainly proved a financial success under the conditions of the locality where it was introduced and where a refining process had been sought previously in vain. I have ventured to bring it to the notice of the Institute in the hope that it may prove of some interest as a solution of a practical problem, such as is often presented to the metallurgist in the remote mining regions of the West. The method was used first at the Lyon Mill at Dayton, Nevada, and has been adopted at other tailings-mills on the Cornstock. These mills treat two classes of tailings: "sand," or; material which has passed previously through the pans of the ore-mills; and " slimes," or the fine clayey material which, coming from the battery, is too light to settle in the tanks inside of the mills but is

Jan 1, 1886

By Edward L. Clark

The year 1954 witnessed great activity in the field of geology as applied to mining. The search for in nearly all districts is becoming more and more intensified as established reserves are being depleted. Much geologic work has been directed to finding extensions of known orebodies, but prospecting in new areas has constituted a large part of the program of many operators. The acute need for additional reserves has brought into the search all the tools known to the geologic profession. This is reflected directly by frequent references to geophysical and geochemical methods in the regional reviews that follow. The lone prospector of the early days of metal mining has been eliminated almost completely by modern scientific methods involving surface and subsurface geology, exploratory drilling, geophysics, and geochemistry. Nearly all new exploration is based on long-range programs coupled with studies of regional geology to determine the structural environment of areas of mineralization. The success of this approach has encouraged new operators in the field of exploration to adopt similar policies. Only in the search for uranium ores is the individual prospector still active, but the familiar picture of the burro heavily loaded with grubstake, gold pan, and pick and shovel has been replaced by the Geiger counter and the scintillometer carried by hand, by truck, or by airplane.

Jan 3, 1955

By P. Hadzeriga

There are two places in the world where potash, trade name for potassium chloride, is economically recovered from naturally occurring brines by solar evaporation. One is at the Dead Sea and the other at Wendover, Utah. American Potash and Chemical at Trona, Calif. recovers potash from natural brines, but uses fuel to accomplish evaporation. Solar evaporation is always desirable, because of low costs, however artificial evaporation may be economical if a group of very valuable salts are recovered. This is the case for the American Potash operations at Trona. Solar evaporation is limited by low working temperatures, which in most areas of the world is between 18 and 45°C. In many cases the average working temperature is about 25°C. However, solar evaporation will have to accommodate itself to the highs and lows of each 24 hour period, and to the different average temperatures during the months of the year. Therefore, solar evaporation, although more economical than artificial evaporation, has a tem- perature limit which greatly reduces the chances of its application. The feasibility of solar evaporation as a means of recovery of values from a particular brine, may be evaluated by the use of phase diagrams showing the several components present. This paper is restricted to the five component system: C1-, SO4=, Na+, K+, Mg++, and H2O, which correspond to brines found at Wendover, Utah, the Great Salt Lake, and sea water bitterns. THE BONNEVILLE OPERATION AT WENDOVER, UTAH For more than 25 years Bonneville, Ltd., now a division of Standard Magnesium and Chemical Co. (recently acquired by Kaiser Aluminum and Chemical Corp.), has been recovering potassium chloride from the brines found in the desert area just east of Wendover, Utah. Solar evaporation of the brines is possible as a consequence of relatively low precipitations (year average: 4.8 in.), and of dry and hot summer months. The brine, collected by a series of approximately 67 mi. of ditches crossing the desert, is fed into solar evaporation ponds. Evaporation which takes place from around the middle of May to about the end of September, permits the crystallization of approximately 90% of the originally present NaCl on what is called the "General Pond Area". Further evaporation,

Jan 1, 1964

By T. Egleston

For several years 1 have been engaged in studying the behavior of iron and steel under varying conditions of tension and compression, as well as of shock and abrasion. Some of these observations have been communicated to the Institute at various times. Within the past year I have been looking at the various observations that I have made as a whole, and have been led to the conclusion that there is a regular law of fatigue and refreshment of metals, and that the change which produces either the fatigue or refreshment, is a. chemical one, which is, however, in almost all cases accompanied by physical and molecular changes at the same time. That metals under conditions that were more or less well understood became worthless, has been known for many years. It has been known to blacksmiths that iron and steel, when improperly treated in their fires, become "burned," as they call it, and could no longer be used, and some of them have had a scrap heap into which such material was thrown. A few of them knew that after a period more or less long the iron or steel recovered some of its original properties and could, with many precautions, again be used, but that these phenomena followed any law has not to my knowledge been announced. My attention was first attracted to the varying conditions under which iron and steel rails break in service. It was not long before I became convinced that there was a general law applicable to all metals which allowed of their being used with safety within certain limits, and caused their rupture when the use extended beyond these limits, and this law I have called the law of fatigue- of metals. When me observe the causes of deterioration in iron and steel rails, we find that they are principally shocks, either slight and frequent, like those produced by the passing of a train over a road-bed in good order, which produces a vibration sensible to the ear laid on the rail, for very long distances, but distinctly audible for only a short one; or from sudden and heavy blows, like the descent of the locomotive and each car successively from a high to a low rail.

Jan 1, 1880

By V. F. Hollister

Although it is apparent that porphyry copper deposits may have formed in the Andean orogen from Permian time onward, commercial deposits thus far developed appear to have Cenozoic ages only. Following Chilean usage, the porphyry deposits are divided into either (1) a stockwork or (2) a tourmaline breccia model. As indicated by evidence cited in the paper, stockwork-type deposits tend to be related to major strike-slip structures which may be either transcurrent or transverse faults related to plate movements, while the tourmaline breccia type may more frequently form independently of regional faults. Stockwork types may be conjugate fractures that intersect and ramify as a network of veins and veinlets, cutting altered rock, and genetically related to a major regional fault, or in other cases they may reflect the intersection of two large fault structures. Circular fracture patterns may more rarely occur in stockwork deposits in response to a specific intrusion. Tourmaline breccia types are characterized by circular and radial fractures genetically connected in some way with touramline breccia pipe development or an intrusive piercement that preceded it. Each structural model contains mineralized intrusions which have a close time-space relationship to ore, and in each model mineral paragenesis is similar, regardless of age or location in the plate. Also, each model contains the same type of alteration halos (phyllic, argillic, propylitic) as are developed in intrusive centers in porphyry copper deposits found in North America. The potassic zone is exposed best in the older deposits. Examples of each type of deposit are illustrated, demonstrating the feature evolved.

Jan 1, 1975

By R. E. H. Pomeroy

THE statistical data given in this paper are taken from the actual performance of the No. 2 reverberatory furnace of the Nevada Consolidated Copper Co., Me Gill, Nev., for a period of four months, from April to July, 1914. The principal furnace dimensions are: Length, 132 ft. ½ in. at the skim-line level; average width, 18 ft., 10 in. at the skim-line level. The roof is 7 ft. above the skim-line level at the firing end. The average area in the uptake flue is 36 sq. ft., and the area above the skim line under the vulcatory arch is 24.3 sq. ft. Fig. 1 shows a diagrammatic plan and sectional elevation of this furnace. The furnace is equipped with two 400-b.h.p. Stirling waste-heat boilers set in parallel. California crude petroleum is used for fuel and has a specific gravity of 16.5° B., flashing in open test at 199° F. The oil is heated to about 200° F. in a steam heater before going to the burners, requiring about 9 b.h.p. per furnace day to heat it from the line temperature to the burning temperature. Measurement is made by oil meter, checked daily by reservoir readings. The oil is fed by gravity (34 lb. static pressure) to seven low-pressure blast burners of the Steptoe type (Fig. 2). The blast for these burners is supplied at about 40-oz. pressure by a motor-driven Connersville blower of 42 cu. ft. capacity per revolution. The air supplied by the blower through the burners for atomizing the oil amounts to about 10 per cent. of the theoretical air necessary for complete combustion of the oil. The remainder of the necessary air enters the furnace through the burner openings in the firing wall. No checker holes are provided, and the charge holes in the roof are equipped with slide gates and "dog houses? to minimize air leakages. The combustion of the fuel, as shown by gas analysis at the front of the furnace, is practically complete, the carbon monoxide in the gases being less than 0.5 per cent.

Jan 2, 1915

By V. Annamalai, J. B. Hiskey

Abstract-The kinetics of copper cementation on a rotating disc of pure aluminum were studied as a function of chloride ion concentration, rotational speed of the aluminum disc, hydrogen ion concentration, copper ion concentration, and temperature. The optimum experimental conditions for all the parameters were determined. Chloride ion was found to destroy the naturally existing aluminum oxide film, and enabled the cementation reaction to proceed. A two-step rate, observed in most of the experiments, was attributed to the attainment of a roughened surface. An Evans diagram for the copper-pure aluminum system was constructed and utilized in predicting the controlling mechanism of the system. At low temperatures (<33°C), the rate with an experimental activation energy of 20.36 kcal mol-1 was controlled by the presence of an oxide layer. While at higher temperatures presence of an oxide layer. While at higher temperatures (>33° mol-1 was controlled by ionic diffusion. The deposits obtained were pure copper and not a copper-aluminum alloy. The amount of aluminum dissolved was determined for each experiment, and the maximum excess consumption was found to be only 40%. The structural characteristics of the copper deposits were studied using a scanning electron microscope. These observations indicated that the deposits were either bulbous, massive crystalline, or dendrites of different degrees of fineness depending on the experimental variables. The reaction rates seemed to depend on the deposit structures in a predictable way when a particular experimental parameter was varied.

Jan 6, 1978

By R. T. Mishler

I WISH to express my keen appreciation of the article on the above subject by Coe and Clevenger.1 It has been doubly interesting to me, for the reason that the experience recorded and the principles evolved practically parallel the results of similar investigations made by myself and others at The Lucky Tiger Mine, El Tigre, Sonora, Mex. An outline of the work at El Tigre may aid in confirming the principles expressed by Coe and Clevenger. El Tigre has the unenviable distinction of possessing a slime with a much lower settling rate than any recorded in the article discussed. Under most favorable conditions the settling rate is about one-third that reported for the Liberty Bell mill, and one-tenth that reported for the Nipissing, Golden Cycle, and Presidio mills. This slow settling characteristic of Tigre ore has necessitated careful investigation of settling phenomena throughout the various evolutions of the plant. PREVIOUS SETTLING INVESTIGATION AT TIGRE During construction work at the mill, the Metallurgical Engineer in charge, D. L. H. Forbes, ran a series of experiments on settling. His tests proved that deep settling tanks were not ordinarily necessary. The use of tanks 2 or 3 ft. in depth was suggested.2 Later experiments demonstrated that the following principles of settling applied to Tigre pulp.3 1. In settling dilute pulp, settling rates are independent of pulp depth. 2. In settling thick pulp, settling rates are approximately proportional to pulp depth.4

Jan 3, 1917

By C Gunther

Ore deposits of commercial grade are local concentrations of great rarity when considered in relation to the area of unmineral¬ized land surfaces, and they must therefore be considered as the products of exceptional and complex conditions. The data collected from a great number of individual deposits are sufficient to permit certain broad generalizations in regard to the conditions favorable to ore deposition which even numerous exceptions do not invalidate. The broadest general relation of ore deposits is with intrusive rocks, and while there are notable exceptions, the great majority of ore deposits have a visible or closely inferred connection with intrusive rock masses. Conditions that permit the dissipation of the ore-bearing vehicles do not permit the concentration of metals in deposits; the prime factor to consider in this connection is that structural conditions must be such as tend to concentrate and not to dissi¬pate the ore-bearing solutions. The disadvantage of extrusive rocks is at once apparent; any metals the magma may have contained are dissipated at the surface and are lost; with the exception of tiny vugs and cracks in quickly cooled flows, no concentrations of metals are known in extrusive rocks, and the lack of confinement and quick cooling apparently do not permit extrusives to exert mineralizing effect upon the rocks with which they come in contact. The close mineralogical similarity between extrusives and intrusives, and the great difference in mineralizing power is a proof of the ease with which magmas part with their metallic content, and of the mobility of the ore-bearing vehicles in comparison with the parent magma.

Jan 1, 1932

By William Kelly, Frederick Laist

The slow, tedious and costly method of reducing copper matte to metallic copper in the reverberatory furnace, commonly known as the Welsh process, was displaced by the rapid and inexpensive converter process about fifty years ago. The art of refining copper was for many generations a carefully guarded secret among the Welsh furnacemen and was handed down among them from father to son. An attempt was made to apply it at Butte when the smelting of copper ore first started there but it proved too difficult and expensive under local conditions, and until the introduction of the converter process the entire output of copper was shipped to Swansea in the form of high-grade (60 per cent) matte. Before the construction of the Manhes converter, attempts had been made to reduce copper matte in the bessemer steel converter, but these failed, chiefly because the air was blown through the bottom of the vessel. The air holes became clogged with chilled copper as soon as the reduction started. Manhes partially overcame this difficulty by placing the tuyeres in the side of the vessel, some, distance above the bottom, thus allowing space beneath them for the copper to accumulate. Nevertheless the first attempts to operate such a converter at Butte were not successful, as no means had been provided for clearing away obstructions, which formed to some extent in front of the tuyeres. This difficulty was overcome by drilling holes in the outside wall of the air chamber directly opposite the holes in the shell and lining, so that these could be punched

Jan 1, 1934

By Charles Wright

AT most mines where large tonnages are handled, "bulldozing" or secondary blasting is an important and costly operation. To reduce the large blocks from primary blasting operations or stoping so that they will be small enough to pass through the chutes into the cars at the haulage level, and not too large for the crushing plant, requires blasting. Often this is done by placing a few sticks of dynamite on top of a block with or without a capping of mud, but to consume less dynamite and to promote safety, most secondary blasting is now done by blockholing, or the drilling of holes 6 to 12 in. long in the blocks, using only a part of a stick of dynamite per hole. Regardless of the method of blasting, however, the term "bulldozing chamber" is applied to the room where this work is done. Bulldozing chambers permit secondary blasting at all times in a safe place without disturbance to the other mining operations. The chambers are usually high above the haulage level and well below the stope level or open-pit floor. In most instances the material is passed through a grizzly in the bulldozing chamber, but sometimes no grizzlies are used. One to four raises extend from the chamber to the stope floor and one or two from the haulage level to the chamber floor. Occasionally large slabs of ore or rock choke the raises above the bull-dozing chamber, and these have to be blasted by attaching a bundle of dynamite sticks on the end of a long pole and placing them up in the raise between the pieces causing the choke. This is called "chute-blasting." To give a picture of the progressive developments in the use of the bulldozing chamber, a few typical mines that show the application of this method to both metal and limestone mines have been selected for description here. Limestone mines have been included because many metal miners do not realize to what extent the nonmetallic, or rock, miners are now applying metal-mining methods successfully in their operations. The bulldozing chamber is the "neck of the bottle" for some mines.

Jan 1, 1935

By V. Vahatalo, E. Hakapaa, H. Tanner

Recently modernized, the surface plant of the Outokumpu mine in Finland incorporates a number of ideas meriting close scrutiny from this side of the Atlantic. The mining methods make extensive use of concrete in some unusual ways. Design of the headframe and surface plant represents the latest thinking of European engineers and includes an integral Koepe hoist. The deposit is in eastern Finland, province of North Karelia, 30 miles west northwest of Joensuu and at 60&apos;44&apos; N, latitude. Pyrrhotite, pyrite, chalcopyrite, and sphalerite mineralization occurs in a shear zone in quartzite near a body of serpentinite. Two lenses have a total length over 12.000 ft, with remaining reserves of the 3 to 4 pct Cu ore estimated at about 15 million metric tons.

Jul 1, 1955

By Marvin P. Barnes

Definition The term mineral inventory is a relatively new designation, born of the computer age and grown to common usage with the development of computer techniques for extending drill-hole sample values to regularly gridded data blocks representing in situ mineral values. The term has been generally accepted by geologists and engineers because it has a precise meaning which avoids many of the ambiguities of ore reserve. A mineral inventory is an estimated inventory of mineral in place and is usually achieved by dividing the deposit into regularly spaced gridded blocks to which are assigned estimated values using various extension techniques. A mineral Inventory makes no presumptions about the minability of the blocks or their cutoff grade. A mineral inventory estimate may be good or poor according to how much is known about the deposit, how extensively it has been sampled, and what techniques have been employed to assign estimated grade to the blocks Such an inventory, however, does not change with time, economic conditions, or mining technology, but only with new and better data and methods. Thus, the mineral Inventory is an excellent designation for describing mineral value distributron within a deposit&apos;s geological setting

Jan 1, 1979