Search Documents

By L. W. Kemph

The thermal expansion characteristics of aluminum alloys have been examined by several investigators, among whom may be mentioned Shakespear,' Schulz,2 Hidnert13 Hidnert and Sweeney4 and McCullough.' Shakespear compared the expansion of a series of aluminum alloys containing 14 per cent copper, with separate additions of about 1 per cent each of manganese, tin and zinc with that of pure copper. Schulz examined the expansion of aluminum and zinc and some aluminum-zinc alloys. Hidnert determined with a high degree of precision the exp:tnsion characteristics of pure aluminum, some aluminum-copper, aluminum-zinc, aluminum-silicon and some commercial alloys.' Hidnert and Sweeney examined the expansion characteristics of aluminum-beryllium alloys. McCullough, by an interferometer method, determined the expansivity of some aluminum-copper, aluminum-magnesium, aluminum-iron, aluminum-nickel, aluminum-silicon and aluminum-manganese alloys. Incidental to an investigation carried out during the past six years and leading to the development and exploit,ation of an aluminum piston alloy of relatively low thermal expansivity, the expansion characteristics of a wide variety of alloys were examined. Some of the data which might be of general interest are gathered in this paper. Experimental Procedure The apparatus used was essentially similar to those developed by the Bureau of Standards6 and Howard Scott,? with a few minor changes for expediency. The specimen was approximately 4 in. long and the differential length changes between specimen and the quartz tube were

Jan 1, 1933

By R. Buehl

ALTHOUGH the main features of the transformations occurring in 18-8 have been published already,1-4 certain conclusions merit questioning and discussion. The questions may be summarized as follows: PERCENT REDUCTION BY COLD ROLLING FIG. 1.-VARIATION OF FERRITIC INDUCTION AND PERCENTAGE OF FERRITE WITH COLD REDUCTION. Composition of Alloy: C, 0.08; Mn, 0.40; Si, 0.24; P, 0.014; Cr, 18.13; Ni, 8.94. 1. If ferrite is formed by cold-working austenite, what happens to the carbon with which the ferrite and austenite are both pre-sumably supersaturated? 2. What is the nature of the alpha-ferrite formed at grain boundaries by chromium-carbide precipitation at these boundaries?

Jan 1, 1939

By Thomas Fraser

There are large coal reserves in Argentina, Brazil, Chile, Colombia, Peru and Venezuela, and growing productive industries in Brazil, Chile, Peru and Colombia. The paper describes current activities in these coal fields, and improvement programs that are in progress, or are planned. Special emphasis is placed on improvements in mining and preparation practice, and expansion of production that have been accomplished by American equipment and technical assistance.

Jan 4, 1951

Jan 1, 1885

By Francis L. Sperry

Up to within a few years, the consumption of nickel has been more directly dependent upon the available supply than that of any of the other useful metals. The Gap mine, in Lancaster county, Pennsylvania,* has been, for the last quarter of a century, the only property in this country furnishing nickel in paying quantities. Its yearly output was about 300,000 pounds of metallic nickel, or nearly half the amount used annually in the United States. Foreign nickel from mines on the New Caledonia islands, in the South Pacific, found entrance into our markets as the production of the Gap mine fell off. The price of nickel was constantly maintained, and no special effort was made to extend its use. Over-production was cautiously guarded against, and all surplus metal was held by the banking-houses of the Rothschilds, who assumed the bonded indebtedness of the Sociètè le Nickel. The opening of the Ontario nickel-mines has, however, brought about a radical change; and nickel from the Sudbury district can be delivered in New York within four days, and in European markets within two weeks, as against two months consumed in transporting South Pacific ores. Former prices have been irretrievably smashed, and European trade-journals comment favorably on the influence which Canadian nickel has had in making lower prices, and breaking the backbone of the " nickel trust." Production and Costs. The quantity of nickel produced and the prices which it commanded may be briefly summarized as follows: The total production of the world from 1840 to 1860 was about 100 to 250 tons yearly of metallic nickel; from 1860 to

Jan 1, 1896

By Guy Ruggles

IN this paper the authors aim to chronicle the experience and salient points brought out in changing flotation reagents at a concentrator which had probably been using a minimum amount of oil at a minimum cost per ton, to a more complicated system requiring a partial chemical control. The original oils were coal tar and pine oil. The new reagents are line, xanthate and pine oil. It was found that there were no insur-mountable difficulties and eventually the cost of the new reagents per ton of ore proved to be very little more than that of the old. LIME PLANT When the question of handling lime came up there were two propositions open: (1) to handle the lime dry; (2) to handle it wet in the form of an emulsion. Granting that a dry lime feeder would function properly, delivering lime uniformly, the chief objection was the dust that would be raised when these feeders were being charged or operated, as the only possible location was on a gallery beneath which men were working. With this objection the handling of lime as an emulsion seemed to he the better scheme. The lime plant which was first installed was for experimental work on one section. This was gradually changed and developed until it was of sufficient size to accommodate 20 sections. The various changes will not be discussed and the following description deals only with the fully developed plant. Crude as it is, and perhaps somewhat expensive to operate, the lime-handling plant has been quite successful. Much has been learned which will pave the way for a better installation in the future.

Jan 1, 1927

By G. D. Van Ardsdale, A. W. Hudson

Heap leaching, as practiced at Rio Tinto, Spain, while one of the oldest, and probably one of the cheapest, methods of extracting copper from its ores, has not had, until recently, other than experimental application in this country. This has been due partly to a mistaken idea that the Rio Tinto ores possess some obscure and mysterious quality that renders them alone suitable to the process, partly to the fact that tests properly made meant the expenditure of large sums of money and several years time, and partly to the fact that favorable commercial and other conditions are not often found. This paper gives some views on the chemistry and mechanism of the method, an account of the preliminary experiments, and the final plans adopted for a large-scale installation of the method by the Phelps Dodge Corpn. for treating low-grade ore from Sacramento Hill, Bisbee. If results comparable with those obtained from the test heap are to be had from the large plant, this plant will operate on the lowest-grade sulfide ore now being treated commercially in the country. The method has several advantages: The installation cost is low. Interest charges must, of course, be made both on the cost of the ore delivered to the plant and for the plant itself, but as these are low, there is considerable advantage in the ability to regulate output by more or less complete shutdowns in accordance with market and other conditions. The amount of labor needed is small, and the cement copper produced may be considered nearer a finished product than the sulfide concentrates from a mill, and certainly means less installation cost per ton to put into final form by present methods. At Bisbee, conditions were favorable for a trial of the method for, in the preparation of the Sacramento Hill orebody for steam shoveling,' a large amount of material below concentrating grade had to be moved to

Jan 1, 1923

By John T. Norton, Robert W. Lindsay

A number of detailed investigations of the physical changes accompanying age-hardening have raised the question as to the possibility of some phenomenon preceding the actual process of precipitation. There is considerable evidence to indicate that in the first stages of the aging process there is a pronounced distortion of the crystal lattice. This is particularly marked in duralumin. It would be of considerable theoretical interest to know the nature of this distortion as compared with that produced in other ways and to find out whether, in supersaturated alloys, it is a necessary antecedent to the formation of a second phase by precipitation. It was believed that a study of the age-hardening char-acteristics of a normally aged alloy compared with one that had been mechanically distorted might supply some useful information on these points. In addition, information would be obtained regarding the effect of a mechanical distortion on any subsequent stage in the aging process. Duralumin was chosen as the material for this investigation because the various aspects of its aging behavior can be shown in detail by suitable variations of the aging temperature. Also, probably more work has been done on this class of alloys than on any other. In spite of the many published results, it was felt that the experiments would be significant only if all of the work were done on samples from the same source and if they were examined under identical experimental conditions. Previous Work The many studies of the mechanism of aging in duralumin have been more or less crystallized by a series of papers by Fink and Smith1~2~3 and a recent paper by Cohen.~ The former authors believe that a simple precipitation theory is adequate to account for the various phenomena

Jan 1, 1939

By John Chipman, K. C. McCutcheon

To a very large extent the quality of a mild steel ingot is determined by the manner in which it is poured into the ingot mold and its behavior during the first few minutes after it has been poured. The formation of the solid rim of metal around the periphery of the mold, the effervescent action of the liquid steel within this solidified rim and the upward or downward movement of the metal level are indications of what is going on beneath the surface of the liquid metal, especially at the interface at which solidification occurs. Observation of this "rimming action" enables an experienced observer to predict the thickness of the sound skin of the ingot and the location and extent of cavities or "blowholes" caused by entrapment of gases. The control of rimming action at the hands of a skillful steel pourer is a vital part of the control of quality in mild steel sheet, and the behavior of the liquid steel during the rimming period is a useful criterion of the melting and refining practices employed in the open hearth. The behavior of rimming steel during solidification depends primarily upon the evolution of gases from the molten metal and it is therefore a problem of considerable interest to determine the nature and amount of the gases evolved. A number of attempts to determine either the amount or the analysis of the evolved gases have been reported. Klinger,1 in 1925, analyzed the gases extracted from rimming, semikilled and killed steel ingots and found that the chief constituent of the rimming gas was carbon monoxide. The relatively large amounts of nitrogen reported in his first few samples may have been due to incomplete removal of air from the gas-collecting mechanism. McKune2 reported similar studies of rimming ingots from which surprisingly large proportions of nitrogen and hydrogen were evolved. Ameen and Willners3 determined both the amount and composition of gases extracted from unkilled ingots with the aid of diminished pressure. . Their ingots weighed only 80 kg. (176 lb.) and apparently were solid within two or three minutes, so that their

Jan 1, 1938

By Rudolph Gahl

RUDOLF GAIL, Miami, Ariz.-Since I wrote the paper on flotation which is in your hands, important developments have taken place, and, for this reason, I will try in a few words to bring it nearer up to date as far as the Inspiration plant is concerned. You, may have noticed that in the Inspiration concentrator, flotation is not solely relied upon for the recovery of the coarser material, but that flotation tailings are split into a sand and a slime product on drag classifiers. The sand product is treated on tables which thus supplement the work of the flotation machines. Extensive tests have shown, us that, if we wanted to, we could leave out these tables and substitute additional flotation machines, as they will make fully as good, if not a better recovery than tables on the deslimed feed, but the treatment would be more expensive, especially in view of the fact that oils are required which cost more than those which we are now using in our main flotation plant. We have, however, decided to apply flotation treatment to our table middlings. I would also like to add a few words regarding the treatment of oxidized copper ores. Although our experience shows that the addition of hydrogen sulphide and other soluble sulphides effects a very good recovery of copper carbonates with certain ores, we have not been able to prove that we could use it advantageously for the ore mixture which we are treating in our concentrator, and for this reason, have looked toward leaching for extracting the carbonate and silicate copper that we are losing now. Experiments in this direction are going on and are giving very encouraging results. It may interest you to hear that we intend to use limestone for the precipitation of the copper which goes into solution, as electrolytic precipitation seems to be out of the question on account of the diluteness of the resulting solutions, and precipitation by iron was rightly objected to on account of the unavoidable contamination of the water supply. We feel very hopeful about the success of our limestone precipitation which, if it holds what it seems to promise, will develop into a novel feature of copper metallurgy.

Jan 10, 1916

By Charles R. Keyes

PAGE I. Introductory............ 140 II. Location and History...........140 III. Surface-Relief of the District....... 141 IV. General GeoloGic Features........ 142 1. Main Relationships and Map....... 142 2. Résumé of Geologic History..143 V. Geologic Formations Represented...144 1. Broader Considerations......... 144 2. Geologic Section.......... 145 3. Nomenclature.......... 146 4. El Pasan Limestones..146 5. Santa Rita Limestone.... 146 6. Silver Shales........... 147 7. Bella Shales........... 147 8. Berenda Limestone..147 9. Grande Limestone... 148 10. Lake Valley Limestone........ 148 11. Sierra Limestone.......... 149 VI. Unconformities........... 149 VII. Geologic Structure.......... 150 1. Main Characteristics......... 150 2. Folding........... 1.50 3. Faultings........... 150 4. Relations of the Eruptives...153 VIII. Geologic Relations OF the Ore-Bodies...... 154 1. Governing Factom......... 154 2. Position.......... 154 3. Relations to Foldings...155 4. Relations to Lines of Dislocation... 15.5 5. Relations to Present Surface.Relief..156 6. Relations to Eruptive Rocks...157 7. Relations to Lithologic Nature of the Rocks.... 158 IX. MINERALOGIC CHARACTER OF THE ORES...... 158 X. Origin of the Ore.Deposits..159 1. General Statement......... 159 2. Original Source of the 0re.Materials...160 3. Contact-Metamorphism of the Region... 161 4. Process of 0re.Concentration..162 5. Lowering of Ground-Water Level..162 6. Formation of Cerargyritic Ores...163 XI. Recapitulation........... 168

Jan 1, 1909

By C. A. Stetefeldt

The iron-ore deposits worked by this Company occur in lenses 200 to 1000 feet long and 5 to 80 feet wide, and stand at an angle of from 65' to 75, with a vertical height of 250 to 500 feet, other lenses occurring below. A number of the deposits were first worked as open pits, which in some cases were carried to the depth of 150 feet, when, owing to the weakness of the walls, underground mining was adopted. While the ore was being removed from the open pit, shafts mere in several instances sunk into the foot-wall, the intention being to mine the ore with breast-stopes of an approximate height of 20 feet, followed by underhand-stopes of the same height, leaving floors between of the necessary thickness to support the walls, or to effect the removal of the ore by means of what is known as the stall system. As the work progressed, however, it was found that the walls (which are of chlorite) were too weak to permit the working of breast-stopes 20 feet high, there being frequent heavy falls of ground from the hanging and, in some instances, from the foot. The plan of following breast-stopes with underhand-stopes was, therefore, abandoned. By working breast-stopes only, but little more than one-half of the ore could be removed, and that only at an excessive cost, the ore being so hard that power-drills with 3 1/8-inch pistons . and 6-inch stroke, working under 60 pounds of compressed air, are able to drill but 8 feet in ten hours as a yearly average, while from 6 inches to 2 feet is a common result of ten hours' drilling. It was plain that some other system of mining must be adopted, and it was proposed to sink by levels of 75 feet, carrying in the cross-cuts from the shafts and working out the ore each way from the shaft from foot to hanging, and from 15 to 20 feet in height. When this has been done, drift-sets consisting of caps and legs are set up the whole length of the opening and connected with the cross-cut; the necessary openings for ladder-ways and chutes or mills are timbered from

Jan 1, 1893

By Richard A. Busch, Roy L. Soderberg

Large, high, open stopes resulting from vertical crater retreat (VCR) and similar methods are usually filled with sand tailings to support the stope walls and make it possible to mine the pillars. The hydrostatic head resulting from these high stope fills demands extremely heavy bulkheads in the crosscuts to withstand the pres- sure. Occasionally, these bulkheads fail because there are no drains or the installed drains are inadequate. Costly flooding of the mine and loss of life result from these failures. With proper design of blanket drains and filters, the fill can be made failure-proof, requiring only a minimum bulkhead, designed specifically for zero water retention. The effectiveness of the blanket drains can be increased by laying perforated pipes on the bottom of the crosscut within the blanket drain. These drains can have a safety factor of 10 with minimal expense. When the water is properly drained, the hydrostatic pressure on the bulkhead is reduced to zero, leaving only the lateral pressure of the sand. This lateral pressure is partially dissipated by arching and shear against the crosscut walls and consolidation of the tailings as the water is drained. The bulkhead should be placed at least one cross-cut diameter back from the collar of the drawpoint.

Jan 1, 1983

By Charles R. Keyes

Prefatory,........323 Foundation of classificatory schemes in general..325 Past opinion on the classification of ore-bodies,.326 Nature of ore-deposits,....... 326 Definition........326 Fundamental law of origin.... 327 Significance of ore-bodies,.... 327 Date of origin........328 Original source of ores..... 328 Alteration of ore-bodies,....329 General methods of ore-formation.... 330 Ascension verm lateral secretion... 330 Replacement.......330 General factors in classification....332 Genesis in ore-classification....332 Literature of ore-deposits...... . 333 Criteria of ore-classification,..... 335 Primary grouping of ore-deposits..... 338 Hypotaxic deposits......341 Eutaxic deposits...... 341 Ataxic deposits....... 313 Secondary categories of ore-bodies....343 Ternary phases of ore-deposition.....344 Types of hypotaxic or surface deposits..... 344 Illustrations of eutaxic ore-bodies.... 347 Examples of ataxic ore-bodies.....352 Recapitulation.. .. .. .. 355 Prefatory. Much has been written on the genesis and classification of ore-deposits. Much remains yet to be written on the subject

Jan 1, 1901

By John C. Branner

Within a couple of years I have received many inquiries in regard to the manganese-mines of Brazil. These inquiries were doubtless directed to mc because I had lived and traveled in Brazil for more than eight years, and was therefore supposed to be pretty well acquainted with its geology and mineral resources. Somewhat to my chagrin, I not only knew nothing of manganese-mines in that country, but I had never before heard of the mineral having been found here in quantity, and I did not even know in what State the mines were located. The present summer found me in Brazil again, trying to finish up some of my early geological investigations along the northeast coast, and I have used the occasion to find out something about the manganese-deposits. Very little is known of these mines, even in Brazil. While at Pernambuco I was told that they were in the distant interior of the State of Bahia. In August I reached Bahia, and there I found out, concerning the mines and their geology, enough to be worth telling for the benefit of those interested in the mining or using of this mineral. Thus far, all the manganese-ore shipped from this State has come from two mines, the principal one of which is known as the Pedras Pretas mine. This was the first mine opened, is the best developed, and was the original discovery; the second one is on an adjoining tract, and the general geology and natural conditions are about the same in both. The Pedras Pretas mine is on the Nazareth-Amargosa railway, twenty-six kilometers west of the town of Nazareth, which is on tide-water, at the head of navigation, and is reached from the city of Bahia by a small side-wheel steamer that runs across the bay of Bahia and up the Rio Jaguaripe

Jan 1, 1900

By Plato Malozemoff, A. M. Gaudin

IN modern practice the major portion of an ore is reduced to flotation size by fine grinding. As the result of grinding fine enough to liberate most of the minerals, a substantial portion (generally 5 to 15 per cent) of the ore is inadvertently reduced to a size much finer than that necessary for liberation. This portion of most flotation pulps is very refractory to recovery by flotation. A reduction of one-quarter or more in recovery in this range of extremely fine particles can be observed. The loss in metals caused by overgrinding is appreciable. That this loss is characteristic of very fine particles has been suspected for some time;(l)† however, it was definitely quantified only recently.(2) Definite reduction in float-ability with reduction in particle size beyond a critical size of maximum floatability can be accepted now as an established fact. Formulating the Hypothesis In looking for the cause of the ill behavior of the finest particles it may be well to consider the essential differences between fine and coarse particles. A difference that immediately comes to mind is their intrinsic difference in size and consequently in relative extent of surface. If one agrees that attachment of mineral particles to bubbles must follow direct encounter of particles with bubbles one is forced to conclude(3) that the probability of encounter between a mineral particle and a bubble varies directly as the size of the particle, provided the particle is small compared to the bubble. In other words, the finer the particle the poorer its chance of being recovered in a given time of flotation. There is an effect, implicit in this theory, which should overcome the effect of excessive fineness of the particles; namely, flocculation of the particles. The floccules can be conceived as being simply larger particles and therefore capable of becoming attached to bubbles. And, indeed, in all the cases in which a sulfide mineral of near-colloidal size was successfully floated the mineral (but not necessarily the gangue) was flocculated. Moreover, it was shown experimentally(4) that galena previously flocculated by inorganic flocculators and then added to gangue

Jan 1, 1935

By David R. Mitchell, R. B. Hewes

MANY processes for cleaning coal that are in use depend primarily on physical properties of coal and refuse other than specific gravity and surface conditions relating to froth flotation. These properties are shape, coefficient of sliding friction, resilience, friability, magnetic susceptibility, and electrical conductivity. In many of these processes specific gravity does have some effect and many separators are designed to utilize more than one of the physical properties cited. Although the processes described herein do not have a widespread application, yet for specific coals and specific conditions, they are economically important. A problem confronting many coal-mining districts is the marketing of the slacks or screenings and dust passing the final sizing screens. Processes in commercial use installed primarily to increase the form value, and hence the market value, of these slacks and dusts include briquetting, packaging, and low-temperature carbonization. MECHANICAL PICKERS Machines utilizing shape, frictional resistance, and differences in resilience of coal and impurities are usually called mechanical pickers. They require a closely sized feed, therefore their use is confined to the pea, nut, and egg sizes. Various types of these devices are described by Berrisford, 1, 2 Taggart,3 and Peele.4 Shape In general, coal differs in shape from its accompanying dirt throughout the range of commercial sizes. Coal, breaking into roughly cubical particles, contains a greater number of axes that are approximately the same length than does the dirt. The latter, consisting of pieces of slate and shale and lenses of pyrite, is flatter in nature. Further, flat coal often has a dirty, slaty appearance, even though of high quality. Mechanical pickers known as flat pickers, or "flatters," are widely used in the Pennsylvania anthracite region to remove flat coal .from the final clean coal. This practice greatly improves the appearance of the final market product. Flat pickers for removing impurities or flat coal ("flats") are usually installed on shaker screens, shaking conveyors, and chutes. In Fig. 1 three

Jan 1, 1950

By J. A. Herbst, G. E. Agar

The effect of fluid viscosity on the classification of solids in a liquid-solid cyclone was investigated. The separation size was found to be proportional to Additionally, it was found that the prediction of flow rate through a cyclone is dependent on a Reynolds criterion. Above a critical value, the flow can be predicted by a simple equation, whereas, below this value a variable orifice coefficient must be introduced. INTRODUCTION The solid-liquid cyclone is widely used as a device for classification, thickening, and heavy media separations. The more important variables and how they affect the performance of a cyclone are known and have been the subject of several investigations.' In general, these studies have paid little attention to the viscosity and those which have, introduced it through Stokes settling considerations. Systems which contain appreciable amounts of swelling clays exhibit viscosities much greater than water, and in these systems the viscosity term becomes important in determining the separation size. The work described here was done to determine in a Newtonian system the dependence of separation size on viscosity. BACKGROUND The separation size for a cyclone classifier has been related to the parameters of the cyclone by an equation of the form: where a is probably between 1.3 and 1.5, ß is between 0.50 and 0.57, and 6 has a theoretical value of 0.5. where y has a value between 1.8 and 2.0. Although these relationships are empirical, equations that differ only in the exponents have been derived from theoretical considerations. Those interested in the origin of these equations are referred to some of the original work.6,7 MATERIALS AND PROCEDURE The laboratory apparatus used in this study is pictured diagramatically in Fig. 1. Feed slurry was pumped from an agitated 15-gallon plastic tank by a centrifugal pump driven by 3/4 hp motor. The static pressure of the feedstream and thus the pressure drop through the cyclone was measured on a gage located as close to inlet of the cyclone as possible. When samples were not being taken, overflow and

Jan 1, 1967

By J. H. Wernick

IN temperature-gradient zone-melting1 a molten zone is moved through a solid or across a solid surface by the establishment of a temperature gradient. This technique has both practical and fundamental aspects. One practical application is to make p-n junctions for semiconductive devices, particularly for devices in which the junctions are desired within the semiconductor. From a fundamental point of view, the technique is being investigated as a method for determining diffusivities in liquid alloys, and preliminary diffusivity results have been reported by the writer." In this paper, the effects of crystal orientation, temperature, and molten zone thickness in temperature-gradient zone-melting, and the bearing of these effects on diffusivity measurements and n-p-n junction formation are discussed. Experimental Procedure An effect of crystal orientation was noted in early experiments. To facilitate its study, movements of wire zones across a surface, rather than through the body of a single crystal, were observed for various surface planes and travel directions. The experirr-entai setup is illustrated in Fig. 1. The graphite end-section for the high temperature heater has an apron about 1/16 in. above the upper surface of the crystal. This apron insures that the surface temperature of the block is equal to or greater than the temperature within the block at every point, Thus, the zone does not penetrate the block and convection in the liquid is minimized. The experi-through a block is shown in Fig. 2,

Jan 1, 1958

By George R. Gardner, Kenneth B. Ray

THE application of wet cleaning processes for the beneficiation of bituminous coal has created in some localities a problem in the recovery and disposal of fine solids in the washery water. The maximum allowable concentration of these solids in the washery circuit that is consistent with satisfactory operation of the cleaning units remains a controversial point. It has, however, been generally recognized for a number of years that some degree of control should be exerted over the concentration of such material. Early methods of control involved intermittent or continuous discharge of a portion of the plant slurry into near-by streams or settling ponds, and this persisted even after the adoption of settling tanks or cones. The practice is not always economical, for two reasons: first, because of the waste of coal, and, second, because it is sometimes difficult and expensive to obtain an adequate supply of water. The latter condition often is aggravated by chemical treatment of the make-up water that is necessary to prevent excessive corrosion of plant equipment. The modern approach to this problem has been the adoption of continuous thickening devices. However, because such equipment occupies considerable plant space and is somewhat expensive to construct, the practice of loading these thickeners beyond their rated capacity is widespread, therefore often the performance of such units is not altogether satisfactory. In recent years, European washeries have increased the rate of settling of the fine coal from the slurry by the addition of specially prepared starch solutions. These reagents cause flocculation of the solid particles and thereby increase the rate of sedimentation. The first important work on the flocculation and clarification of coal slurry was done by Henry, who developed the Henry process and used it successfully in Belgian preparation plants. Soon after the initiation in Belgium, the process was introduced into England, where subsequent investigation developed similar processes, which were successfully used in

Jan 1, 1939