Search Documents

By David L. Sikarskie

The measurement of residual stress fields using X-ray diffraction techniques requires the removal of successive layers of material from the specimen. In the process of removing these layers, the underlying residual stress field is altered; hence, if the original stress field is desired, corrections must be made to the measured stresses. Although these corrections already exist for a number of cases, an alternate procedure is outlined herein whereby the corrections are presented in series form. This form is numerically more convenient within certain ranges of correction depths and in its simplicity gives additional insight into the factors affecting the corrections. It, further, readily permits determining the proper slice depth to remove and the effect on the correction of both specimen thickness and magnitude and form of the measured residual stress itself. ONE of the techniques currently being used to determine residual stress fields is X-ray diffraction. Since X-rays are diffracted essentially from the layers of atoms near the surface of the specimen, of the order of 0.0001 to 0.001 in. depending on conditions, the method can only determine stresses* in this very thin surface region. Therefore, if the residual stress field at some depth into the specimen is required it is necessary to remove successive layers of material taking measurements after each cut. In the process of removing a thin surface layer of stressed material, however, the over-all equilibrium of a cross section of the specimen is disturbed with the result that the internal residual stress which existed before the slice of material was removed is altered. This alteration of stress occurs after each slice and its effect is cumulative. Thus, if the original stress distribution is desired, corrections must be applied to the measured stresses. These corrections can be found by satisfying equilibrium on each new cross section. These corrections have been derived in detail for a number of cases, e.g., cylinders, bars, plates,' and also are given in Appendix VI of Ref. 2. In each of the above cases the correction terms require the evaluation of definite integrals of the measured residual stress distribution. In general, this is indeed the way one would proceed with the corrections. There are a number of instances, however, where the integrals can be replaced by a series form of correction which is considerably more convenient numerically and, also, gives added insight into the factors which influence the corrections. Such a form of the correction is particularly useful, for example, if one is interested in designing a test such that stress corrections will be small. Also, the question of what depth of slice to use in relation to both specimen thickness and residual stress distribution itself must invariably be answered. Questions of this type can be readily answered using a series form of correction. In addition, if the correct residual stress distribution is needed only for limited depths into the specimen the series correction provides numerical results which are equivalent to the integral correction. I) DERIVATION OF THE SERIES CORRECTION The problem to be considered here is that of a bar or plate,* i.e., either one or two dimensions of the specimen is large compared with the third. Also, the residual stress distributions considered depend only on z, see Fig. 1. In view of this it can be shown' that a stress correction, based on simple beam theory, satisfies all conditions of "elasticity theory" and hence is the correct (and only) solution. The integral form of the correction (this assumes that the measured residual stress is a piecewise continuous function) as given in Ref. 1 is:

Jan 1, 1968

By T. B. Counselman

PROBABLY the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of being high in phosphorus because of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetite area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake Superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mines, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion Range of Minnesota, were hard and lumpy, and opened up the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium, and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi, and it is these big open-pit deposits that constitute our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers, and tables, which later were replaced by classifiers. Ore particles finer than 100 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. Jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes. The latest and most important process that has been

Jan 1, 1943

By A. E. Outerbridge

I had the honor to present to the American Institute of Mining Engineers at the Pittsburg meeting, February, 1896, a paper having the foregoing title, in which I said : " It has generally been accepted as a fact that cast-iron, under the influence of repeated shocks, becomes brittle, and will finally break under a blow which otherwise it would have withstood. It will probably surprise metallurgists, therefore, to learn that experiment disproves the supposed fact, and establishes exactly its opposite. " The result of about a thousand tests of bars of cast-iron of all grades, from the softest foundry mixtures to the strongest car-wheel metal, enables me to assert with confidence that, within limits, cast-iron is materially strengthened by subjection to repeated shocks or blows." Three tables were appended showing increase of strength

Jan 1, 1905

By P. W. Ramsey, D. P. Kedzie

INCREASING demand for improved strength-weight ratios made on aircraft structures has resulted in a gradual increase in the tensile strength requirements for steels used in such applications. As the cyclic loads often are more critical than static loads, and the fatigue properties are generally the design criteria, the question arises as to whether an improvement in fatigue properties accompanies the increased tensile strength. The present investigation was undertaken to determine the relationship between fatigue and tensile properties for an aircraft quality steel in the 155 to 280 ksi (1000 psi) tensile strength range, using the Prot method of fatigue testing. Procedure and Results After preliminary work to establish proper heat treating procedures for this heat of aircraft quality electric furnace steel (a Ni-Cr-Mo-V steel," AMS- Prot Fatigue Testing Method—The determination of the endurance limit by the conventional Wohler method can be time-consuming and easily require 20 specimens when statistical variance is to be established. This is also true when endurance limit loads are determined on actual parts or subassem-blies, and the desirability of a reliable accelerated method has been evident for some time. The primary advantage of the Prot method of fatigue testing is in reducing the number of specimens and the time required for each test. Unlike the Wohler method, every Prot specimen tested con- tributes to the determination of the endurance limit, and the authors have been able to duplicate Wohler results obtained with 20 specimens with only half the specimens and a fourth of the total cycles. This new technique for defining the endurance limit was proposed in 1948' by Marcel Prot and consists of progressively increasing cyclic stress until fatigue failure occurs. By varying the load rate, a, a useful relationship is found to exist with failure stress, so that for steel the failure stress appears to

Jan 1, 1958

By Frank Wartman

RECENTLY Horace Freeman1 obtained a patent on a successful method of conducting a roasting procedure described as to general features by Carl Schnabel2 almost forty years ago. Essentially, the Freeman process of roasting consists in introducing the finely powdered sulfide mineral, suspended in air or any other suitable gaseous medium, into the upper portion of a heated chamber. The stream of suspended particles is directed vertically downward. A counter-current stream of gas introduced at the bottom of the chamber flows upward. The mineral particles are oxidized as they fall through the heated atmosphere of the chamber. All air required for the oxidation may be admitted either at the top or the bottom of the chamber, or may be divided between the top and bottom inlets in any desired proportion. Heat may be recovered by passing the gases leaving the furnace through a waste-heat boiler or other form of interchanger. In speaking of the results obtained in roasting pyrite, Freeman says:3 Steam yield from the boiler exceeds 1 pound of steam per pound of pyrite con-sumed, which pays the cost of operation of the burner. The oxide produced is in the form of fused particles or hollow shells of magnetite, containing about 65 per cent of iron. It contains the gangue material ordinarily produced in flotation concentrate, of course, but it is being found that most of this can be eliminated by magnetic separa-tion, and that the sulfur content, as consistently produced, is below 0.2 percent. This material is especially interesting as a high-grade iron ore, free from phosphorus and low in sulfur. It may be sintered or briquetted. It is even more interesting as a raw material for sponge-iron production, to be directly smelted in electric furnaces without the usual cooling of the iron powder and magnetic separation between the reducing kiln and the electric furnace.

Jan 1, 1933

By S. Arthur Krom

(Wilkes-Barre meeting, June, 1911.) RECENT experiments indicate that the usual type of concentrating-table is not only poorly adapted to produce the desired results, but also is based upon an incorrect principle, namely, the use of riffles to perform the work of stratifying the various minerals. We have heard a good deal about riffles for concentrating-tables; exhaustive experiments have been made to discover the proper form of riffle, or to prove the superiority this or that form; disputes and patent-litigation have arisen over the matter of riffles, and thus many have been led to believe that the riffle is the saving-device upon which the process of concentration depends. In the present paper it is proposed to show that the riffle is greatly overrated as to the part it performs in the concentration of minerals, and that, in the near future, it may possibly be eliminated entirely from that process. The experiments in question have shown that the troublesome riffle can be considered of secondary importance at the most, and should be so classed in the construction of a concentrating-table built upon the right lines. The action of any form of riffle on a concentrating-table is such as to upset and retard the process of settling and stratifying the various minerals on the table-deck. From the deck of a riffled table no concentrates can be delivered until the deck is "bedded," that is, until a sufficient amount of metallic values have been fed to the table to spread over a large portion of the deck, forming a substratum of the heavier minerals. This substratum must be maintained by the feed within quite narrow limits, and directly proportional to the rate of discharge from the table, in order that the bed shall not be lost. On the other hand, the riffles having a very lim-

Jul 1, 1911

INTRODUCTION The regional characteristics of porphyry copper deposits in South America southward from Pantanos and Pegadorcito, Columbia, will be summarized. The age of formation of deposits spans the period from the Permian to the present. Where possible, the general characteristics and the individual structural features of the deposits are integrated into the plate tectonic model. Individual deposits cited in this chapter, located in Fig. 1, are the best known and most fully described, and form the Andean copper belt (Peterson, 1958). Smaller porphyry copper deposits fall both east and west of the line of large, high grade deposits (e.g., Chuquicamata and Toquepala) that make up the spine of this belt. Most of those smaller deposits (e.g., Mi Vida [Koukharsky and Mirre, 19761) are omitted from Fig. 1 and Tables 1 and 2, however. Neither the Andean orogen nor the individual deposits within it are as well de- scribed in the literature as are their counter- parts in the Cordilleran orogen of North America. Therefore, generalizations relying on regional geologic mapping, geophysics, and isotopic geochemistry lack details pertinent to this type of deposit in the Cordilleran orogen. The South American porphyry copper province has been described by Hollister ( 1974) to include most of the Andean orogen excepting the tin province of Bolivia. Porphyry copper deposits have not been commonly found within the tin belt, although copper-tin (e.g., San Rafael, Peru) and copper-tungsten (e.g., Llamuco, Chile) de- posits are known. James (1971) shows the depth to the Moho to be appreciably greater where the tin belt exists, but disclaims any genetic significance from the coincident appearance of the tin-tungsten province and the inhibition of porphyry copper development where the sialic crust thickens. Dates on tin mineralization in this belt (Clark and Farrar, 1973) are similar to some dates for porphyry copper mineralization known else- where in the Andean orogen. It seems that some mechanism is needed to explain the geographic separation of porphyry copper- molybdenum and simultaneous tin-tungsten- molybdenum metallization within the same tectonic system and appearing at similar distances from the trench. The thickened crust of the tin belt is one of the few known differences. Tables 1 and 2 list some of the most important porphyry copper deposits explored to date, but do not include Antaminas, Peru. or a number of other large skarn deposits

Jan 1, 1978

By E. F. La Vigne

ON Aug. 10, 1884, the Retsof Mining Co. began the sinking of an 18 by 12-ft. shaft at Retsof, N. Y. Rock salt was reached in 1885, in September, at 1008 ft. below the surface. The first salt was shipped in the fall of 1885. A timber breaker was built in 1886. In July, 1895, there was a consolidation of the Retsof Mining Co., the Greigsville Salt & Mining Co., the Livonia Salt Co., and the Lehigh Salt & Mining Co. These consolidated salt companies are now known as the Retsof Mining Co., a subsidiary of the International Salt Co. Eventually all of the mines were closed except the mine of the Retsof Mining Co., at Retsof, Livingston County, New York. On July 6, 1921, about ½ mile south of the original shaft and plant of the Retsof Mining Co., a new 9 by 28-ft. concrete-lined shaft was started. The shaft is 1063 ft. deep from the top of the shaft collar to the bottom of the salt bed. At the same time a reinforced-concrete breaker and other buildings were erected. This new plant began opera-tions on Dec. 15, 1923. It was designed for a capacity of 3000 tons in 8 hours.

Jan 1, 1936

By Noah Fields Drake

This paper is devoted chiefly to the coal-fields of the western part of the province of Chili and the eastern part of the province of Shansi; but the outline of this belt will give some idea of the extension of the coal-fields over northeastern China. This part of China is topographically divided into: (1) the mountainous peninsula of eastern Shantung; (2) the coastal plains, extending W. and SW. from the gulf of Pechili; and (3) the mountains and table-lands N. and W. of the coastal plains. The plains extend N. and W. from the gulf to within from 10 to 25 miles of the Great Wall, while their SW. extension covers western Shantung and reaches W. along the Yellow river almost to the southern boundary of Shansi. A line joining the mapped coal-fields, shown in Fig. 1, almost gives the western boundary of the plains; since these areas lie on the border of the plains—except the Tsê Chou field, which is on the table-land, 20 to 25 miles from that border. The coal-fields which have been mapped and investigated by the author are shown in Fig. 1. The one at and around Tongshan is known as the K'ai-p'ing coal-field; the one W. of Peking has been called the Wang-p'ing coal-basin; the one SW. of Pao-ting and N. of Chêng-ting may be called the Lingshan coal-field; and the one at and around Tsê Chou is known as the Tsê Chou coal-field. I. The K'ai-p'ing Coal-Field. As is shown in Fig. 2, most of this field lies in the coastal plains, and is therefore covered by alluvium and loess, which have buried the older rock-beds, and the more gentle and older topographic outlines, to such an extent that most of the re-

Jan 1, 1902

By Milo W. Krejci

The plant and quarries of the Inland Portland Cement Co. are located at Metaline Palls, Wash., about 128 miles north of Spokane, on the Pend Oreille river, and within 10 miles of the Canadian border. The plant is one of a chain of cement plants controlled by the Lehigh Portland Cement Co., of Allentown, Pa. Work on this plant was commenced in June, 1910, and was completed in April, 1911, but on account of some delays in the construction of the power plant, the works were not put into operation until August, 1911. Since then it has been in continuous operation and has furnished the Inland Empire with a high grade of cement. Fig. 1 is a view and Fig. 2 is a plan of the works. Water Power Development.—The source of the water supply for the hydro-electric plant of the Inland Portland Cement Co. is Sullivan lake, a body of water approximately 5.5 miles long and' 0.5 mile wide, situated in the Kaniksu Forest Reserve. A wooden crib dam was installed so as to raise the elevation of the lake 25 ft., and the additional storage capacity was taken up by the diversion of Sullivan creek into the lake by means of a wooden flume, 0.25 mile long, 6 by 8 ft. in cross-section, and a ditch 1,200 ft. long. The water from the lake follows the natural water course to an intermediate storage reservoir, which was created by the construction of an earthen dam. This pond was used in connection with the saw mill which was installed at this point. Besides the earth dam, there was also built a crib, at the point shown in the sketch map, Fig. 3. This crib dam is 35 ft. high. From this point the excess water follows the natural course of Sullivan creek to the Pend Oreille river. The water is taken from this intermediage storage by means of a 6 by 8 ft. wooden flume approximately 13,000 ft. long. This flume is built up on the side hill, piling being driven most of the way on

Jan 1, 1914

By L. C. Snider

All important industries have certain basic principles in common which govern them and give them a family resemblance. In addition, each industry has a certain individuality due to some principle or principles which govern, or are accepted as governing, that industry and which is not effective in others. The customs and practices of an industry depend on these basic principles much as the corollaries follow a proposition in geometry. After the proposition is proved or is accepted as proved, the corollaries are seen to be true almost without additional evidence or proof. In many cases, the corollaries are more important in practical affairs than the proposition on which they depend. By continued application the corollaries may come to be accepted as law and the fact that their truth depends on the correctness of the fundamental proposition is forgotten or ignored. If it is discovered that an error was made in demonstrating the proposition and that the proposition is untrue, the corollaries are, in most cases at least, equally untrue. Considerable time may be required, however, to realize the fact that the corollaries have failed, particularly if they have been embodied in custom and law. For example, in the business of government the proposition that women are intellectually inferior to men was formerly considered, by most men at least, to be duly proved if not axiomatic. This propositiot was never embodied in law, but its corollaries—that the rights of the wife in property and even in her own children were inferior to the rights of the husband, and that women had no place in governmental affairs—were duly incorporated in law or so completely approved by custom that they had the effect of law. Developments of the past few decades have proved, to the satisfaction of the majority, that woman's intellectual inferiority to man had not been satisfactorily demonstrated, and that the proposition that she was inferior, although accepted for many generations, was untrue. It was not so great a shock to men to discover that this proposition was wrong as it was to find out that its corollaries were also untrue and that the laws embodying them were not good laws and were subject to repeal. The adjustments which give women equal rights with men

Jan 1, 1932

By DeVerle P. Harris

Risk for most mineral investments is greater than that of average business ventures, because the physical and economic characteristics of the mineral deposit are never known with certainty. Inasmuch as the merits of a potential mineral investment cannot be fully appraised without consideration of the impact to the investor of the possible unfavorable events associated with the adoption of the project, methods of risk analysis are important in project evaluation and investment selection. The conceptual framework for risk analysis and the means by which some of the recommended practices might be implemented are examined. In addition to the normal business risk due to market forces, the physical and economic characteristics of the mineral deposit are never known with certainty, for only partial or indirect information is available, such as data from drill cores or surface and underground workings. Consequently, risk for most mineral investments is greater than that of average business ventures. Inasmuch as the merits of a potential mineral investment cannot be fully appraised without consideration of the impact to the investor of the possible unfavorable events associated with adoption of the project, methods of risk analysis are important in project evaluation and investment selection. This paper examines the conceptual framework for risk analysis and means by which might be implemented some of the recommended procedures. Utility Theory A discourse on risk and its impact upon investment selection quite often leads the reader into the concept of utility theory, for utility theory is a device constructed by economists to measure the satisfaction an individuai receives from a good; in the case of investment analysis, that good is the outcome of an investment. It briefly is reviewed here to describe the reaction of the individual to risk and as a stepping stone to other techniques more suited to risk analysis at the level of the firm. Utility theory proposes that an investor possess a utility map (curve), such as indicated in Fig. 1, which indicates the value in utiles of potential monetary rewards to an individual with some specific endowment of resources. Points on this map are obtained from the following relationship:

Jan 1, 1971

By P. J. Soltis

Direct as well as indirect evidence of a-phase ordering was found in a "near-a" type titanium alloy, Ti-8Al-1Mo-1V. The annealed alloy showed an anomalous decrease in second-stage creep rate at 950°F (510°C) and 47,500 psi. Anomalous increases were noted in initial yield stress after 500 hr creep exposure and in tensile strength after 1100 hr creep exposure. Debye-Scherrer X-ray diffraction patterns obtained on fine-grained polycrystalline speci-ment showed much line broadening and development of superlattice lines after 500 hr at 510° C. Examination with the light and electron microscopes failed to reveal phase changes in thermally exposed material, but detailed metallography is presented illustrating the plastic and fracture characteristics of the alloy. Electron-metallographic evidence is presented, however, which shows the nature of the nucleation and growth of ordered regions from the disordered a in annealed material. In the original phase diagram of the binary Ti-Al system constructed by Ogden et al.1 aluminum was shown to be soluble in a titanium over a wide temperature range at concentrations up to about 30 pct. Subsequently, a number of papers2-7 have appeared which indicate the existence of either intermetallic compounds and/or ordered phases in the a field up to 25 pct Al. In the most recent of these, Goldak and Gordon paw7 have determined unequivocally the ordered hexagonal D019 structure for Ti3Al in a 25 pct Al alloy. No superlattice lines were observed above 1112°F (600°C). Previously, the embrittle-ment encountered by Crossley and Carew4 in low- temperature heat treatments of binary Ti-Al alloys low in aluminum had been attributed to the appearance of a new phase in light micrographs. In the present work, direct as well as indirect evidence is presented showing the existence of a-phase ordering in what is essentially the binary Ti-8A1 alloy containing small percentages of the ß stabilizers molybdenum and vanadium, i.e., the "near-a" Ti-8Al-1Mo-1V alloy. Although Bohanek and Kessler8 have shown that this alloy has good stability at temperatures up to 1100°F (593°C), the present work shows instability at 950°F (510°C) where long exposure times were used. Light and electron microscopy proved very useful in revealing the mechanical behavior of ordered a and led to the conviction that ordered "near-a" alloys may have remarkably good properties and useful engineering applications.

Jan 1, 1965

James W. Neill, Pasadena, Cal. (communication to the Secretary*):—Professor Hofnlan's paper brings the art up to date. As I was one of the pioneers in this business, I beg to give the following incomplete data regarding my efforts in this line. In the year 1883, while I was in charge of the smelting-operations at Mine La Motte, Mo., there mas at the concentrator an unusually large protluction of a middle product, locally called " iron," which carried considerable values in nickel and cobalt, and which it was desirable, for this reason, to treat by itself. The works could not spare a furnace for the purpose; and to handle this product I improvised a " roast-hearth " from an old " lead-hearth." This was a small cast-iron furnace of the uslial construction, about 2 by 4 ft. in dimensions, with a hollon- cast-iron back, through which the wind circulated before entering the tuyeres. I had a cast-iron grate made to fit this hearth, and placed it tlush with the lip, or apron, and above the tuybres. On this grate, which had round holes about 0.25 in. in diameter, and a total surface of about 20 by 40 in., I roasted the nickeliferous pyrite product; starting the fire with kindling, then adding charcoal, and then gradually feeding the sulphides with a shovel, so as to cover the fire, choke down blow-holes, and get an even bed. Blast at a pressure of 3 or 4 oz. was supplied by a Can-blower. When a cake of roasted material had formed, it was removed with a steel bar, or fork, to the lip of the furnace, and thence into a wheel-barrow. The fine material which had renlained unmelted, but very hot, on top of the cake would promptly ignite when the cake was broken up and removed. The fire would then be covered with fresh material and

Jan 1, 1911

Jan 1, 1913

By THEODORE DWIGHT

Members of the Institute have already received a special pamphlet descriptive of the United Engineering Society building, and wilt doubtless be interested in the progress that has been made up to date-February 24th-in erecting this home for the engineering profession. The old buildings on lots Nos. 25 to 33 W. 39th St., New York, were,' removed many months ago, but final contracts for the new, building were not let until the summer of 1905. The size of the building is 115 ft. on 39th Street, and 88 ft. in, depth; the height from, the sidewalk to the top of the parapet is 220 feet. The cubic contents of the building from the. bottom of the basement floor, to the top of the roof, including the pent houses, is 2,290,000 cubic feet. The number of light's, in the building will be between 4,000 and 4,500. The air supply for Auditorium and Lecture. Halls will amount to nearly 10.0,000 cu. ft, per minute, and the exhaust. to 90,000 cu. ft. per minute. In excavating for cellar and foundations, the average depth where good rock was. found was 37 ft.-it varied, however,: from 27 to 65 ft., due to an old water-course having run through the center of the lot; this condition, and the presence of soft rock, which rapidly disintegrated when exposed to air and water, made the foundation-work very difficult. As two of the column-footings of the building have to sustain a weight of 3,000,000 11) each, the most substantial foundations are necessary; 13,000 cu. yd. of earth were excavated for the foundation and basement; and 1,600 cu. yd. of concrete were necessary, to build up the footings. In the completed building there will be about 3,500,000 bricks. Owing to the number of auditoriums, and their location, and the placing of the library on the top floor; where allowance will have to be made for the enormous weight of 300,000 books, the structural steel work has been unusually complicated in this building. For instance, over the auditorium there are two 60-ton plate-girders, made up

Mar 1, 1906

By N. Arbiter, C. C. Harris

Analysis of ball and pulp flow in ball mills indicates that three factors may become critical with increasing mill diameters: ball size, fraction critical speed, and average pulp flow velocities. Ball diameters may need to be decreased and fraction critical speeds increased with ores which show decreased breakage rate coefficients above 1.2 mm (14 mesh). With 5.5-m (18 ft) and larger mills at higher circulating loads, pulp flow velocities may become capacity limiting and also may limit increases in ball mill diameters.

Jan 1, 1985

By K. A. Grace

Reserves are the basic foundation of any mining enterprise, but a lack of understanding of the concept of resources and reserves is still a frequent cause of failure in mining ventures. A review of the development of the resource-reserve concept emphasizes the necessity for a common language, and the classification system as set out by the US Geological Survey and Bureau of Mines is advocated as the basis for this. Because of its strong economic connotation, the term reserves should be severely restricted in its use, and should encompass mining and processing factors. Modifications to the basic definition of reserves to accomplish this are proposed. Caution must be used in the quantification of undiscovered or hypothetical resources, particularly in juxtaposition with known resources data.

Jan 1, 1985

By Karl L. Fetters

In the process of making steel in the open-hearth furnace the refining of the metal during the working period of the heat is largely accomplished through the agency of the slag. From the birth of the process until the present day steelmakers have recognized the importance of the slag in determining the composition of the metal and the quality of the product. The general relationships between slag composition and metal analysis have long been known, at least in a qualitative or approximate fashion. For examples, the iron oxide content of the slag is higher on lower carbon heats; the more basic slags are higher in iron oxide for a given carbon content; certain amounts of iron oxide and lime arc required for phosphorus removal and a high lime-silica ratio is needed if the sulphur content of the metal is to be diminished. In recent years a number of quantitative relationships involving these and other variables have been developed through plant and laboratory studies by numerous investigators in this country and abroad. The direct comparison of laboratory and open-hearth data involves the question of the degree to which each approaches the conditions of chemical equilibrium, a question which, from the open-hearth standpoint, we are scarcely yet in position to answer. And, although a considerable body of dependable equilibrium data has been obtained in the laboratory, this work has not yet been extended to cover the ranges of slag composition encountered in basic open-hearth practice. In the present study we shall not attempt to draw comparisons between data from the two sources; nor do we attempt to draw conclusions as to the approach to chemical equilibrium in the open-hearth furnace. Many of the operating variables that are likely to be erratic or unrecorded during the earlier stages of the heat become more consistent and arc more readily subject to observation and control during later stages. For example, undigested lime or ore gradually goes into solution, the rate of carbon drop levels off, and the temperature of the metal is brought under control. For these and other reasons a greater degree of self-consistency is likely to be found among data obtained during the

Jan 1, 1940

By Karl L. Fetters

In the process of making steel in the open-hearth furnace the refining of the metal during the working period of the heat is largely accomplished through the agency of the slag. From the birth of the process until the present day steelmakers have recognized the importance of the slag in determining the composition of the metal and the quality of the product. The general relationships between slag composition and metal analysis have long been known, at least in a qualitative or approximate fashion. For examples, the iron oxide content of the slag is higher on lower carbon heats; the more basic slags are higher in iron oxide for a given carbon content; certain amounts of iron oxide and lime arc required for phosphorus removal and a high lime-silica ratio is needed if the sulphur content of the metal is to be diminished. In recent years a number of quantitative relationships involving these and other variables have been developed through plant and laboratory studies by numerous investigators in this country and abroad. The direct comparison of laboratory and open-hearth data involves the question of the degree to which each approaches the conditions of chemical equilibrium, a question which, from the open-hearth standpoint, we are scarcely yet in position to answer. And, although a considerable body of dependable equilibrium data has been obtained in the laboratory, this work has not yet been extended to cover the ranges of slag composition encountered in basic open-hearth practice. In the present study we shall not attempt to draw comparisons between data from the two sources; nor do we attempt to draw conclusions as to the approach to chemical equilibrium in the open-hearth furnace. Many of the operating variables that are likely to be erratic or unrecorded during the earlier stages of the heat become more consistent and arc more readily subject to observation and control during later stages. For example, undigested lime or ore gradually goes into solution, the rate of carbon drop levels off, and the temperature of the metal is brought under control. For these and other reasons a greater degree of self-consistency is likely to be found among data obtained during the

Jan 1, 1940