Search Documents

By Elmer R. Kaiser

COMBUSTION of coal and transfer of heat from flames and gases to boiler surfaces continue to be of great interest to engineers here and abroad. Numerous investigations have been in progress to improve furnace and boiler performance and economy. The importance of better understanding of the processes and opportunities for improvement is apparent when it is remembered that heat from at least 500 million tons of coal a year the world over is being transferred to boiler water at efficiencies ranging mostly between 50 and 90 pct. Even slight gains in efficiency, economy, and labor saving become very significant when multiplied by the enormous quantity of fuel consumed. Also the competitive position of the large coal, oil, and gas industries in satisfying the fuel consumers is greatly affected by the achievements made through technical progress with each fuel. This paper is part of a continuing activity of Bituminous Coal Research, Inc., to extend the knowledge of coal utilization for steam generation and to seek promising directions for future research and development in cooperation with others. Particularly in the latter regard, numerous interviews were held during the last three years to seek the experience and advice of boiler and combustion- equipment manufacturers, electric-utility executives, and fuel engineers. A wealth of published information was also reviewed, which together with the interviews pointed to the advisability of further work on ash and sulphur control.

Jan 3, 1954

By G. R. St. Pierre, S. W. Gilby

The equilibrium vapors established over Fe-Cr-Ni alloys containing up to 50 pct Cr at 1600°C were determined by collecting the effusate from thoria Knud-sen cells. From these data, the activities of iron and nickel in the ternary alloys have been calculated. In a separate set of measurements, a mass spectrometer was used to determine the activities of the three components in a series of Fe-Cr-Ni alloys. In binary Ni-Cr melts, the activity coefficient of chromium referred to pure solid chromium as standard state is less than one at low chromium contents but is greater than one for melts containing more than 30 at. pct Cr. For Ni-Cr melts containing less than 10 at. pct Cr, In ?Cr = 0.15-0.92 N2. Ternary activity diagrams for Fe-Cr-Ni alloys are presented. In iron-rich alloys, the interactions between the three components are negligible; however, in nickel-rich alloys, the three principal interactions have significant positive values. THE activities of components in binary Fe-Ni alloys have been measured both in the solid solution1-3 and liquid solution4-6 temperature ranges. The determination for Fe-Ni melts have been made by three different methods: transpiration,4 Knudsen-cell effusion with analysis of an accumulated condensate,' and Knudsen-cell effusion with direct measurements of relative component intensities by mass spectrometric methods.6 The results obtained by the three different methods in three different laboratories are in excellent agreement and considerable confidence is placed in the activity coefficients for Fe-Ni melts. At 1600°C, the activity coefficients in dilute solution are ?°Ni = 0.66 and ?oFe = 0.40 for the pure liquid components as standard states. Measurements made on solid solution Fe-Cr alloys7-10 indicate that the component activities are slightly greater than ideal. The measured activities in iron-rich Fe-Cr liquid alloy11-16 indicate almost ideal behavior for this system. The recommended activity coefficient of chromium in dilute solution in liquid iron at 1600o C, ?oCr, is 1.18 when referred to pure solid chromium as standard state and 1.04 when referred to pure undercooled liquid chromium as standard state." The conversion factor of 1.14 is based on a melting point of 1857°C and an enthalpy of melting of 4047 cal per g at. for chromium.21,37 The activity coefficient of iron in dilute solution in liquid chromium has not been measured. Activity measurements on solid Ni-Cr alloys have been made by several investigators.17-20 During the review of this manuscript, Fruehan12 published the results of a study on liquid Ni-Cr alloys at 1600°C. He used galvanic cells22 with ZrO2(CaO) as the electrolyte and Cr/Cr2O3 for the reference electrode. His results indicate that ?oCr in nickel at 1600°C is about 1.01 when referred to pure solid chromium and about 0.89 when referred to pure undercooled liquid chromium as standard state. The activity coefficient of nickel in liquid chromium is unknown. The compositions of vapors freely evaporating from some molten Fe-Cr-Ni alloys have been measured by Lyubimov, Granovskaya, and Berenstein.23 Their results, combined with known vapor pressures, indicate strong positive deviation for chromium in iron-rich alloys and strong negative deviation for chromium in nickel-rich alloys. EXPERIMENTAL PROCEDURES This research was undertaken to determine the activities of components in ternary Fe-Cr-Ni melts containing up to 50 at. pct Cr. At the initiation of the research, we decided to use a Knudsen-cell method wherein a portion of the effusing vapor is condensed on a cold plate.' The composition of the equilibrium vapor for each alloy composition is determined in this method by holding the system under constant conditions for a period of time sufficient to collect enough condensate on the cold plate for chemical analysis. The activities of components in ternary alloys can be calculated from such vapor composition determinations by Eq. [1].24

Jan 1, 1970

By W. A. Tiller

The unidirectional freezing of a semiinfinite liquid from one end has been treated by calculating the solute and temperature distributions in the liquid and solid phases with time, when the solid-liquid interface advances at a rate proportional to (time)lt2. The nucleation probability for new grain formation is calculated as a function of the constitutional and thermal properties of the alloy, the pouring conditions and the catalytic efficiency of the nucleating agents. The transition from columnar crystal formation to equiaxed crystal formation is assumed to occur at a critical nucleation frequency for a particular alloy and the quantitative dependence of the ratio (columnar zone length/equiaxed zone length) upon the freezing conditions has been predicted. The effects of (i) fluid flow in the liquid, (ii) heat transfer through a mold wall, and (iii) a finite ingot length, have been explicitly tveated as departures from ideality. These departures from ideality are found to have very important consequences on the ingot stmcture. In Part I&apos; of this series, a qualitative description of the general ingot structure was developed. The factors that determine i) the ratio of the equiaxed zone length to columnar zone length and ii) the grain sizes in these zones, were discussed. In the present paper, topic (i) will be treated quantitatively, and it is intended that topic (ii) will be treated quantitatively in Part 111. The complete treatment has been split in this manner for ease of development and coherency of presentation. The treatments are quite mathematical in nature and, although some of the conclusions to Part 11 depend upon the treatment presented in Part 111, it was felt that the intended audience would find the material more readable and more useful in its present form. To this same end, it seems worthwhile to reiterate some of the qualitative aspects of grain nucleation during ingot solidification before embarking on the mathematical description. QUALITATIVE ANALYSIS In the conventional method of casting, a liquid alloy with a certain degree of superheat is poured into a mold. The outer rim of liquid metal cools rapidly to the liquidus temperature of the alloy and begins to undercool. As the degree of undercooling increases, nuclei of solid begin to form in this chill layer, this nucleation being catalyzed by certain heterogeneous particles in the liquid. The grains in the chill layer which are generally of random orientation, begin to grow inwards because of heat conduction through the mold. The grains usually develop a columnar shape since the frequency of nucleation of new grains in the liquid ahead of the advancing interface is generally insufficient to seriously impede the growth of the original grains. Due to the slow diffusion rate of solute in the liquid, a solute distribution is formed in the liquid adjacent to the interface which is either an excess or a depletion if the partition coefficient, ko, of the solute is < 1 or > 1, respectively. Thus, the liquidus temperature of the liquid adjacent to the interface is a function of position. The actual temperature in the liquid is also a function of position and the temperature gradient at the interface decreases as the interface moves away from the mold wall. Since the rate of advance of the interface decreases with time, the equilibrium temperature distributions and the actual temperature distributions as a function of interface position, X, can be illustrated as in Fig. 1. Thus, a region of liquid may exist in which the actual temperature is below the liquidus temperature. This liquid is contitutionally supercooled and therefore unstable with respect to the nucleation of new grains. Now, since the supercooling in Fig. 1 increases as the interface moves further away from the mold wall, the nucleation rate of new grains will increase. When the nuclea-

Jan 1, 1962

By David E. Nicholas

INTRODUCTION In this paper, a numerical process for selecting a mining method, with the emphasis on underground mass mining techniques, such as caving, induced caving, and stoping, is proposed. In the past, selection of a mining method for a new property was based primarily on operating experience at similar type deposits and on methods already in use in the district of the deposit. Then, the chosen method was modified during the early years of mining as ground conditions and ore character were bet- ter understood. Today, however, the large capital investment required to open a new mine or change an existing mining system make it imperative that the mining methods examined during the feasibility studies and the method actually selected have a high probability of attaining the projected production rates. Although experience and engineering judgment still provide major input into the selection of a mining method, subtle differences in the characteristics of each deposit, which may affect the method chosen or the mine design, can usually be perceived only through analysis of measured characteristics. The parameters that must be examined when choosing a mining method include: 1) geometry and grade distribution of the deposit; 2) rock mass strength for the ore zone, the hanging wall, and the footwall; 3) mining costs and capitalization requirements; 4) mining rate; 5) type and availability of labor; 6) environmental concerns; and 7) other site-specific considerations. This paper encompasses a detailed look at the first two parameters since they, plus mining costs, have the greatest impact on the selection of a mining method. The proposed method selection process is for a project where drilling has defined sufficient geologic reserves, but little or no underground development has been done. Since each deposit has its own characteristic geanetry/grade distribution, and rock mechanics properties, mining method selection should be at least a two-stage process. In Stage 1, the deposit is described in terms of geometry, grade distribution, and rock mechanics properties. Using these parameters, the mining methods can be ranked to determine which are most applicable; they can then be considered in general terms of mining and capitalization cost, mining rate, type and availability of personnel, environmental concerns, and other site-specific considerations. In Stage 2, the most likely mining methods are costed out, based on a general mine plan. Mining and capitalization costs are used to determine a cut-off grade fran which a minable reserve can be calculated; economic comparisons can then be made to determine the optimum mining method and economic feasibility. During the mine planning phase of Stage 2, rock mechanics information would be used to provide realistic estimates of underground opening size, amount of support, orientation of openings, and caving characteristics, and open pit slope angles. If ground control or operational problems should be encountered with the methods being considered, modifications could be made. Although planning on paper extends start-up time, it is cheaper to err on paper than to find the error after mining has begun. METHOD SELECTION - STAGE 1 The main purpose of Stage 1 is to select those mining methods which should be considered in greater detail. The simplest way to do this is by defining those characteristics required for each mining method and then determining whether the characteristics of the deposit are suitable. However, no one mining method is so restrictive that it can be used for only one set of characteristics, as indicated by the classification system proposed by Boshkov and Wright (1973). In the mining method selection proposed, geometry, grade distribution, and rock mechanics characteristics are ranked according to their acceptability for ten general mining methods.

Jan 1, 1981

By Chester T. Sims

RECENTLY, a new type of superalloy material called TD Nickel* has been marketed.&apos; It is a sim- ple, two-phased alloy, consisting of thoria particles dispersed in nickel of rather high purity (Ni-2 pct Thoz). Its mechanical properties appear relatively superior to previous experimental material attempting to use the oxide nonmetallic dispersion concept (except SAP), and superior to conventional nickel-base alloys at high homologous temperatures. This is derived from an interesting method of creating the dispersion, arising during chemical processing of the nickel and thorium salts in solution while reducing the nickel to metal. An evaluation of the thoria phase was conducted at this laboratory. Material and Procedure. TD Nickel was made available, consisting of several inches of 0.470-in. rod, extruded at a ratio of 64: 1, straightened, and centerless ground. Property determinations on this rod by the supplier at 1800°F showed an ultimate tensile strength of 11,400 psi, yield strength of 9600 psi, and 6 pct elongation. Specimens were removed from the rod for as-extruded metallography, and two 1/2-in. lengths supported on high-purity Al2O9 bricks were placed in a laboratory muffle furnace for exposure at 2000° F. The furnace door was left cracked to allow a slight amount of circulation. One specimen was removed at 200 hr for examination; the other was left for 2000 hr. Metallography. The micro structures obtained for the three conditions of exposure are shown in Fig. 1. Elongation of the grain structure in the extrusion direction is readily evident. The grains appear to be up to 0.001 in. (0.003 cm) long, with a length/width ratio of about 10: 1. Allowing for modest local in-homogeneities in structure, no significant change in thoria particle size or nickel alloy grain size occurred during the 2000°F exposure. However, etching depth varies slightly from one specimen to another, changing the number of particles visible. The thoria dispersion appears to be in the order of 0.01 (min) to 0.5 (max) p diam. The minimum diameter is difficult to estimate at X10,000, and may be less. Interparticle spacing appears to be about 0.1 p. Etching effects can be seen, depending upon grain orientation. A cubic etch-pit pattern appears in certain grains, apparently when etching is started by an anodic particle of thoria, Fig. l(c). The cubic pattern appears related to crystallographic orientation, and is prominent when the [ l00 ] direction is perpendicular to the plane of polish. The grains which present a ridged appearance in the photograph appear to be oriented with the [110} direction perpendicular to the plane of polish. Analysis. The thoria particle size was measured by a line intercept method perpendicular to the extrusion direction. Only particle sizes measuring 0.001 in. at X10,000 or larger could be extimated. Within limits of experimental error, particle size distribution appears to be unaffected by exposure, Fig. 2. To check structural stability further, a grain-growth evaluation was made. The number of grain-boundary intersections was counted at X500 on each of several traces normal to the extrusion direction for each condition. It can be seen from Table I that grain diameter appears unchanged by the 2000°F exposure. The slightly finer grain diameter after 200 hr may be attributed to variations in grain size from area to area in the original extrusion. From the present rather limited study of Ni-2 Th on, it appears that: 1) for time-temperature exposure up to 2000 hr at 2000°F (Larsen-Miller parameter = 57, homologous temperature = 0.8) thoria particles of the size studied are highly thermally stable; they do not significantly react, agglomerate, or diffuse; and

Jan 1, 1963

By J. N. Hummel

The methods of electrical prospecting, which employ contact electrodes to produce an electric field in the ground, furnish information concerning the constitution of the material beneath the surface, as indicated by the distortion of this artificially produced field and anomalies therein. To reveal the distortion of such field of known character, it is only necessary to measure qualitatively the direction of the field, using sensitive compensation methods. In such a case, the survey is relatively simple, and that is an important factor from a practical point of view. The distortion of the normal field thus determined permits an easy interpretation and gives approximate information as to the subsurface conditions, without the necessity of a thorough theoretical knowledge of the electrical field. The true field of application of the equipotential lines and search-coil methods, which are based on this principle of directional determination of the electrical field in the ground, is that of search for deposits of economic minerals for the mining industry, although they can also be used in solution of other problems; for example, in the determination of the strike of anisotropic beds. The distortion of the electric field as represented by the picture of equipotential lines or other measured curves is striking only when bodies having conductivities different from that of the country rock are embedded in the underground, or when the underground is anisotropic. It is obvious that methods based on such a simple principle and capable of solving directly many of the practical problems of mining geology have found a widespread application. However, these methods are unable to furnish any information as to the presence, depth and physical properties of layers in the underground, which have different conductivities, but are parallel, or only slightly inclined, to the surface. Where such conditions exist in the underground, the picture of the field

Jan 1, 1932

By C Gunther

A preceding paragraph treats of the irregular manner in which ore deposits occur and the complex factors that control their distribution; the occurrence of metals in oreshoots in individual deposits is equally irregular, and the factors that control such segregation are equally complex. While the dimen¬sions of oreshoots in individual deposits may not be foretold with any degree of accuracy, the occurrence of ore in shoots is not accidental, but is controlled by laws some of which are understood. Any one familiar with permutations and combina¬tions who stops to consider the variety of factors that control ore deposition, and their varying relative importance, will admit that the science of economic geology must advance greatly before the occurrence of oreshoots may be predicted accurately in advance of exploration. The segregation of minerals in any oreshoot must be referred to some condition, or combination of conditions, local to the oreshoot as compared with the remainder of the deposit of low¬grade or barren minerals. Among the localizing factors that have been recognized are, in filled fissures, the amount and distribution of open spaces available for ore deposition, and in replacement deposits, the degree of brecciation giving access to the replacing solutions; the intersection of veins with other veins, dikes, sheeted zones, or porous strata; the impounding of solutions by impervious strata; and the differing precipitative influences of enclosing rocks. A large proportion of important and well ¬defined oreshoots, especially in deposits of deep-seated origin, are not assignable to any of these factors. While a knowledge of the character of oreshoots in general is important, a knowledge of the behavior of the known oreshoots

Jan 1, 1932

Occasionally it is interesting, and sometimes useful, to review the past for early references to our industry, and to learn of the trials and travail passed through before it arrived where it now is- and the results of such a review follow. Some time ago one of our modern playwrights and poets, Arthur Guiterman, turned to coal, with the following result: Afar in the Carboniferous time I grew in Paleozoical slime, A lepidodendron with boughs on my stem And lepidostrobuses grew out of them. My roots in the mud of the ages I spread And up to the heavens I vaunted my head, I throve in the heat of tropical sun, And now I am coal at two dollars a ton

Jan 1, 1939

By E. S. Leaver

THE amount of gold that occurs in a ton of milling ore from most of the large-scale copper mines is so small that unusual care and special attention are necessary to recover it. In some cases the gold is not considered important enough to warrant daily assays of the various products. Considering the large tonnage of copper ores that are now concentrated by flotation, as computed in a recent review, the gross gold content is surprisingly large, probably amounting to over 10 million dollars per year in the United States. The indications are that in many of the copper-milling operations with gold content under $1 per ton, only 50 per cent. of the gold is recovered in the flotation concentrates. Lime is generally used as a depressant for pyrite in the flotation circuit. The authors have shown that high lime or a solution high in calcium ions is also a depressant for gold. Their experiments on several well-known ores show that by careful regulation of the alkalinity of the mill solutions, a higher flotation recovery of the gold can be obtained, together with equally good copper recovery in a good grade of copper concentrates. In cyanidation for the recovery of gold, the best accepted practice demands that the mill solutions be tested and regulated by simple chemical reactions at definite periods during treatment or with each change in the treatment. It is similarly important for the recovery of gold that the solution in the flotation circuit be analyzed for calcium ions at regular periods and at each step in the flotation practice. The lime should be added when and where needed and not in excessive amounts at the head of the mill.

Jan 1, 1931

By J. H. Fletcher

AIR has been cooled, heated, washed; humidified and dehumidified for many purposes and in many industries. At a number of metal mines air is conditioned to reduce the high humidity and unbearable heat found in deep workings, and at some mines air is washed to allay siliceous dust. Steam is introduced into the intake air at many coal mines, particularly in winter, for the purpose of keeping loose coal dust so moistened that the hazard of an explosion is lessened. This paper will describe a further successful application of air conditioning in a coal mine, where, for over three years, all intake air has been cooled to a constant temperature for the sole purpose of preventing roof falls.

Jan 1, 1931

By R. E. Hathaway

INTRODUCTION For a number of reasons, the mineral processing industry has been slow to adopt significant automation of its processes. Most ore grinding operations can be operated manually so the pressure for automation to run the process has not been there. Furthermore, many plants had proven over years of operation that manual operation would produce a profit, so why automate? Until recently, the instrumentation necessary for automation of the grinding process was not available. All this has now changed, however. Increasing costs for labor, fuel, power, grinding media, reagants, and capital equipment have not been matched by the market price of the finished product. This cost-price squeeze has made it mandatory to reduce operating costs and improve the efficiency of the process to remain profitable. A number of other factors have added to the direct operating cost to make the problem even worse. These include environmental pressures to conserve natural resources and reduce smelter stack emissions; increased competition--especially from developing countries, varying economic conditions, stockpiling, governmental controls, and to top it all off, lower grade ore bodies. Although many of these other influences are good overall, they take their toll in cost per ton of delivered product. Fortunately, many operators are finding the solution to the cost-price squeeze in instrumentation and process control. Automated processes yield tighter spec. products, require less operating labor, produce more product from a given plant, and reduce unit cost by increasing process efficiency. The plant manager has a "handle" on the plant through process control so that he can change operating modes as economics dictate by changing the set point of some process controllers. He can even respond to economic conditions by switching control strategies from one that maximizes production to one that maximizes recovery, or minimizes unit cost, etc. This has all been made possible by the advent of on-line analytical instruments and practical process control computers. On-stream particle size (1), x-ray, and silica analyzers are now available and in use in many plants. Digital computer hardware and software has become practical so operators can use it without trying to become computer experts. This chapter describes the approach toward design and implementation of automatic grinding circuit control that has proven to be the most cost effective, based upon results from a number of

Jan 1, 1982

By George A. Yurko

The Cominco smelter, located at Trail, British Columbia, Canada, produces 180 000 metric tons of lead bullion annually in conventional blast furnaces. The resulting slag from these furnaces, 210 000 metric tons annually, containing 18 per cent zinc and 2.5 per cent lead, is treated directly in the slag fuming plant for the recovery of these metals and other valuable metals present in smaller quantities. Slag fuming is carried out on a 55 metric ton batch process in completely water-jacketed furnaces where the slag is blown with a mixture of powdered coal and air. The coal-to-air ratio is con- trolled to maintain strongly reducing conditions, thus, fuming the metals from the slag. The metal vapours are subsequently re-oxidized with air above the bath. The mixture of oxides is carried from the furnace by the gases through waste heat boilers and cooling flues to a baghouse where they are collected. The slag fuming plant, under normal conditions, will treat 700 metric tons of slag daily. The throughput in the plant is dependent on the fuming rate of zinc, which is a function of the composition of the slag, and on the economics, which dictate the extent to which zinc is fumed from the slag. Zinc and lead collected daily as fume average 113 metric tons and 17 metric tons, respectively, corresponding to recoveries of 89 per cent zinc and 98 per cent lead from the slag. The waste heat boilers produce 61 metric tons steam per hour, which is distributed to other processing plants.

Jan 1, 1970

By Toshihisa Adachi, Shosei Serata, Shunsuke Sakurai

Many different methods of measuring the in-situ stress field have been developed in recent years. They are all based on the assumption of elasticity without allowing any viscoelastic deformation. By using the high resolution strain-measuring technique recently developed in the laboratory at Serata Geomechanics, many rocks were found to be viscoelastic. The viscoelasticity of rock media was found to be dependent upon the resolution of the strain measurement. The higher the resolution of the strain measurement, the greater number of rocks could be identified as viscoelastic. All rocks eventually exhibit viscoelastic deformation under high stresses relative to the strength of the material. Therefore, the conventional methods of elasticity become less reliable with increase of ground stress. In deep underground formations, even hard rocks become viscoelastic. At the same time, many ground formations near the surface are actually viscoelastic. A new method was developed in the laboratory to determine the in-situ stress field in viscoelastic rock media. Rocks in general exhibit a small amount of viscoelastic creep whenever mean stress and octahedral shearing stress are changed substantially from their initial states. Such changes take place around a borehole immediately following the drilling although they are short-lived. We developed a viscoelastic method of determining the in-situ stress field by relating the time-dependent behavior of the borehole with the tensor properties and stress field of the underground. In developing the viscoelastic relation, only isotropic and homogeneous

Jan 1, 1970

Jan 1, 1957

By C. G. Dunn, J. L. Walter

Either (100) (001] or (110) (0011 oriented secondaries, or both, depending on annealing atmosphere and material composition, grew in a matrix of 2-dimensional grains. The growth dependence of secondaries of(hkl) orientation in the iron and 0.6 pct Si-Fe is explained in terms of surface energy driving forces and the dependence of these driving forces on both (hkl) orientation and amount of oxygen at the surace. (100) [001] grains grow when suflicient oxygen is present at the gas-metal interface to make y100 the lowest (hkl) surface energy. When little or no oxygen is present at the gas -metal interface, making Y110 the lowest surface energy, (110) (001 1 grains grow. When Y100 and y110 are approximately equal but lowest among (hkl) surface energies, both (100) (0011 and (110) (0011 grains grow simultaneously. An excess of surface oxygen produces complete grain growth inhibition in high-purity iron; i.e., a 3-dimensional grain structure is retained over long annealing periods. However, a small amount of silicon in the iron reduces the growth inhibiting tendency of oxygen without altering the (hkl) surface energy relationships. Some information on annealing twins is presented. SECONDARY recrystallization in high-purity a iron, cold rolled to strip a few mils thick, was reported recently.&apos; The present paper provides additional information on this subject, also furnishes similar information on both zone-refined iron and a high-purity 0.6 pct Si-Fe alloy, and treats the more important surface phenomena that determine to a large extent whether one or more secondary recrystallization textures will appear during annealing. Previous studies on high-purity 3 pct Si-Fe2,3 have shown the importance of (hkl) and impurity-atom dependent gas-metal surface energies on the formation of secondary recrystallization textures in high-purity material. For example, either (100) or (110) oriented grains may have the lowest surface energy depending on the amount of oxygen at the gas-metal interface, and hence the highest driving force for growth if other growth factors are the same. Another important phenomenon in high-purity material is stabilization of the matrix structure; neither impurities nor a strong matrix texture seem to be necessary when recrystallization and normal grain growth occur, developing a stable two-dimensional type grain structure. The average grain size in such a structure is usually between one and two times the specimen thickness. Consequently, most of the grains have grain boundaries terminating at exposed surfaces, and this results in gas-metal interfaces (or hkl surfaces) as well as

Jan 1, 1962

By L. R. Raymond, G. G. Binder

One primary purpose of hydraulic fracturing as a well stimulation technique is to overcome formation damage. The literature provides ways of designing fracture treatments and evaluating their results but not of incorporating formation damage in vertically fractured wells. Results of an investigation of this problem are presented in this paper. Prediction of stimulation ratios in vertically fractured, damaged wells is accomplished with a mathematical model relating stimulation ratio to relative conductivity of fractures whose lengths are not more than about half the drainage radius of the well. Comparison of results from the new model to results in published predictions verify its utility; these results also show that the range of stimulation ratios that can be predicted for undamaged wells is extended to include relative conductivities of less than 300. This extension is important when using fracturing to stimulate wells with high production rates and high native formation permeabilities. For example, large increases in daily oil production rate can be obtained with stimulation ratio increases as low as 1.25. The importance of complete fracture fill-up (uniform proppant packing) is shown through use of the mathematical model. If, at the mouth of a fracture, only a small fraction (1/2 percent) of the total fracture length is not packed with proppant, nearly all the polential stimulation increase is lost. Proppant crushing, compaction and embedment have been shown in laboratory studies to be responsible for low fracture conductivities in wells producing from highly stressed formations. Equipment and methods for testing the effect of stress (overburden) on conductivity of fructures in consolidated and unconsolidated sands are discussed in this paper. Laboratory tests with simlilated fractures in cores from both types of formations showed that crushing, compaction and embedment seriously affect conductivity. Results indicate that similar laboratory tests should be made when accurate knowledge of fracture conductivity is needed to assure good stimulation results for important wells. The chief factor in stimulation ratio reduction was found to be overburden pressure, but the size and type of proppant and the hardness of the formation have significant effects. Fracture conductivity reductions of up to 50 percent were observed with sand propping fractures in consolidated cores; a reduction of 83 percent was measured for an unconsolidated core. The range of effective overburden pressures for which conductivities were measured was from 100 to 5,000 psi. An example fracture design and evaluation problem indicates the usefulness of considering formation damage in planning well stimulation jobs. When damage exists, but its extent and the degree of permeability reduction are not estimated from diagnostic tests, the formation permeability used in planning the job may lead to under-designing. As the example shows, too low a target stimulation ratio can lead to much lower production rates (by half) than could be attained otherwise. Solutions of equations representing several special cases of the mathematical model are presented in graphical form and details of the derivations of the equations are given in the Appendix. INTRODUCTION Since its inception in 1947, hydraulic fracturing has proven to be an effective and widely accepted stimulation technique. In the past 18 years the ability to execute a successful hydraulic fracturing treatment has been substantially increased. The development of design and evaluation procedures1,2 has been one of the major contributions to this increased skill. However, as the art of hydraulic fracturing has moved closer to a science, new problems concerning the design and evaluation of the optimal hydraulic fracturing treatment have arisen. Three questions are pertinent to these problems. I. How is a fracturing job evaluated in a damaged well? 2. What is the effect on the stimulation ratio of not filling the fracture in the vicinity of the wellbore? 3. What is the effect of overburden pressure on fracture conductivity and, consequently, the stimulation ratio? A primary objective of fracturing a well is to stimulate production by overcoming wellbore damage. Presently. however, there is no rational basis for designing or evaluating the optimal fracturing treatment in a damaged well. All present fracture design and evaluation techniques assume that proppants can be uniformly placed in fractures. This assumption may be in serious error, particularly for the portion of a fracture directly adjacent to the wellbore. In this area, turbulence of the injected fluid can cause the proppant to be swept farther into the fracture. Also, loss of fluid from the fracture to the

By R. F. Campbell, R. F. Miller

SIXTEEN steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- [ ] atures. Diagrams summarizing the structures and hardness resulting from these two cooling rates are presented (Figs. 3, 4, 7).† Data were also obtained on the influence of these two elements, individually and in combination, on the depth 0f decarburization observed after furnace cooling (Fig. 8). COMPOSITION OF MATERIAL The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 25-ton Heroult electric-arc furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- [ ] tric induction furnace. The cast ingots were hot-rolled to I.75-in. bars. AIR-COOLED SERIES The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to I830°F. (1000°C.) for 20 min. and oil quenching. They were then reheated to I740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1941

By P. W. Bridgman

It is characteristic of most scientific investigators that they are not satisfied with the discovery of new facts, no matter how curious or unexpected, but that along with the factual discovery there is a constant effort to understand. It appears that one&apos;s interest in, and satisfaction with, the discovery of an array of new experimental facts is enormously increased if one has at the same time a theory or hypothesis guiding one&apos;s expectation of what sort of new experimental discovery may lie around the corner. Conversely, as a theoretical physicist one&apos;s satisfaction with his theory is greatly enhanced if along with the development of the theory can go the discovery of new experimental facts, confirming or perhaps modifying the theory as it grows. Of course, there have been long arid stretches in the history of physics in which new data of unquestioned ultimate importance have piled up, without much inspiration or illumination in the way of understanding. For 50 years spectroscopy had such an arid history, but how irksome this was felt to be is plainly shown by the almost audible relief that greeted the first success by Bohr in injecting understanding into the situation, and by the fresh rush of experimenters into this field when the prospect of understanding had once been offered. The investigations in the field of high pressure, which have occupied me for a long time,&apos; until the last few years have been in very much the same sort of situation as spectroscopy before the advent of Bohr. A great many kinds of data were collected for a great many solid and liquid substances, and there could be no question of the importance of these data, because the uniform change of dimensions produced by hydrostatic pressure is perhaps the simplest conceivable type of alteration to which a body can be subjected. But except for a few isolated flashes, there was no theoretical illumination, so that it had to be to a large extent the enthusiasm of the collector that kept me going. However, within the last few years the wave-mechanics theory of solids has progressed so rapidly that

Jan 1, 1938

By Richard Franchot

From an efficiency viewpoint, the greatest loss of energy to the blast furnace is in its failure to convert more than about a third of the coke carbon from carbon monoxide to carbon dioxide. This result has usually been ascribed to a necessity of a 2:1 excess of CO in order to reduce iron. It has, however, been proved that iron is completely reduced by equal volumes of carbon monoxide and carbon dioxide. Hence there is room for the hypothesis that vaporization, as cyanid, of accumulated alkalis is a serious primary factor limiting the ratio of ore to coke. Observed cyanid vapor concentrations and those measured by the variations of the nitrogen-oxygen ratio in the hearth gases form the basis for a quantitative explanation of the furnace action. As EVERYBODY knows, the blast furnace is a gas producer. As to the reason for this, people are not so well agreed. The significance of the fact is obvious, for the extent to which the fuel leaves the furnace as combustible gas measures poor economy in iron smelting; while good efficiency in this respect means poor gas. The furnace thus works at cross purposes. The present trend of the steel industry is toward. a primary use of the blast furnace as a gas producer with pig iron as a byproduct. Needless to say, this trend is away from improvement in iron making. The production of more and better iron in a given furnace consuming a given amount of coke would seem, at least, to involve a decrease in the relative proportion of the combustible gas. The possibility at the same time, however, of making more and better gas need not necessarily be excluded. (The more the furnace acts as gas producer, the bigger is the sulfur problem.) Whatever the object, it would seem desirable to have a, clear, comprehensive, mathematically exact estimate of why and how the blast furnace functions, to the large degree that it now does, as a gas producer. The literature does not give a definite answer to the question. That for which explanation is sought is the fact that only a minor part, usually not more than a third, of the coke carbon burned is oxidized to carbon dioxide; that the development in the furnace of the fuel energy is thus limited usually to little more than 50 per cent.; that it requires about twice as much fuel coke to make a ton of iron as is indicated by the rela-

Jan 7, 1925

By W. H. Newhouse

DURING the past few years the writer has been impressed by the close relation of many epigenetic orebodies with anticlinal structures. In the literature on ore deposits there is occasional mention that an oreshoot or district is on an anticline, but in most of the descriptions no weight or significance is attached to the relation, and usually the fact is concealed in a mass of structural detail. A few writers have stressed the relationship in a few districts or on a certain type of deposit. Church, Spurr, Butler, Stahl and Schuette have called attention to certain features, but the general extent of such a correlation has not been made known in any publication that the author has seen. A recent article1 on the localization of ore deposits, by well-known geologists, does not consider this common association. The author has seen in the field a number of the structural features described, and in addition has made a fairly complete review of the literature. This paper presents enough of the examples found to show the frequency of the relation to anticlines, and since only a few deposits on synclines are known, all of these of any importance of which the writer knows are mentioned. With certain qualifications which are discussed later, epigenetic ore deposits of replacement or vein type are mostly found where local upwarps of the earth&apos;s crust have taken place. Where formations antedating the ore deposits are present in the proper attitude to demonstrate vertical warping (i. e., more or less horizontal beds) the structural feature on which a mineral district, or mineralized area is located is almost always anticlinal, or domelike in nature. Some or even most of the ore deposits in a given district may be on the flanks of the upwarp, but few major districts are located definitely on downwarped areas. Synclinal basins within certain limits of size appear to be unfavorable to the type of fracturing that admits ore-bearing solutions.

Jan 1, 1931