Search Documents

By Edward B. Cook

The installation of the Gayley dry-air process appealed specially to the management of the Warwick Iron & Steel Go., for the reason that for fifteen years records had been kept at the works of the company, showing the amount of water entering the furnace in the form of aqueous vapor, and careful observations had been made of its effect upon the working of the furnace. Some years had proved much worse in their effect than others, on account, not only of excessive moisture, but also of great variation in the moisture from day to day, and sometimes within a few hours. It had been found impossible to make a satisfactory percentage of high-silicon foundry-iron in summer, even on high fuel; and for some years the endeavor had been made so to arrange the sales that, during July and August, only a small percentage of the iron produced would be required to carry more than 2 per cent. of silicon. Our larger furnace, running on basic iron, year after year, produced in February a tonnage 20 per cent. higher than in August, 011 a much lower fuel-consumption, while, at the same time, the summer months were marked by " messes," tuyeres closed by slips, and other irregularities, constituting serious additional business losses. It will be easily understood, therefore, that the records made at the Isabella furnace after the installation of the dry blast in 1904 possessed special interest, and were closely watched by us. On the basis of our own experience, we argued that if the moisture could be kept low, and also uniform, the cost of installation would be more than justified. The subject was brought before our Board of Directors in the fall of 1905; and in the spring of 1906 it was decided to install a plant of sufficient

Jan 1, 1909

By R. S. Cartwright

TWO types of automatic drilling controls, the Halliburton and the Hild, are now available and are coming into more or less general use in deep drilling. The primary function of both is to maintain a safe limit of torque on the drill pipe, this being accomplished by automatically controlling the weight or pressure on the cutting tool. Neither type will necessarily increase drilling speed, but by permitting advantage to be taken of "breaks" in the hole higher average cutting speed may be maintained. The control is essentially a safety device, and should be considered as such. It is not the purpose of this paper to discuss the merits of drilling controls, although the advantages over manual feed at the brake drum are obvious, but rather to point out some of the limitations. The Halliburton Control The Halliburton control is designed to operate during drilling through the agency of the draw works. Automatic and constant control of the torque on the bit is governed by clutches on the control itself, and the line shaft to drum shaft drives on the draw works. In operations other than drilling the control is simply a jackshaft between prime mover and draw works. It is, of course, adaptable to any type of power. Because control of the torque on the bit is dependent on the various ratios or clutch combinations available on the Halliburton control and the draw works, it follows that there are certain limitations in points of control. Table 1 shows the possible ratios which can be obtained with the control and a popular type of three-speed draw works, it being assumed that the highest possible gear combination—the combination which when engaged will suspend the least amount of weight—has a value of 1.00. According to the table there are "blind spots" in the series. This is true particularly among the lowest ratios, which are most used to suspend the major part of the weight when great depths are reached. It will be noted that there is a difference of nearly three units in the value of the

Jan 1, 1929

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,'J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By Edgar C. Bain

In studying the structural characteristics of martensite it is desirable that a clear conception of the material from which martensite is produced should first be obtained. Any theory of its formation and structure incompatible with the facts of its parent substance, austenite, can be eliminated with little consideration. Austenite is the name applied to solid solutions of carbon and other elements in gamma iron. At temperatures above about 900" C. (1650" F.), pure iron exists in a system of crystallinity1 entirely different from the crystal structure below that temperature. This high-temperature allotrope of iron is of an atomic structure associated with great ductility, having very manifold symmetry and an abundance of easy slip planes. The exceptionally ductile and malleable metals (gold, silver, platinum, copper, aluminum, and nickel) have this same atomic arrangement— the face-centered cubic. The low-temperature allotrope of iron, alpha iron, the solid solutions of which are known as ferrite, has a body-centered cubic arrangement of atoms. Like it, in crystal structure, are the less ductile and malleable metals, molybdenum, tungsten, titanium and chromium. Fig. 1 shows the two atomic arrangements known in iron; the diagrams are drawn to scale. Either of these modifications of iron may dissolve other elements in the solid state; by so doing, the temperature of the transformation is changed. In general 2-7, it appears that a solid solvent metal dissolves a metal solute by substituting foreign atoms in its own space lattice. Thus, iron may dissolve nickel in either of its crystalline forms by permitting an atom of nickel here and there to occupy the normal position

Jan 1, 1924

By Duane H. Haley

The century we live in has been an eventful time for the Third World, particularly the country of Peru. Although it will take one or two generations more to see its end and fully evaluate its scope, it is already clear that during the twentieth century, Peru has entered a dynamic industrial, economic, social, and political revolution. This century has seen the end of old governments, and the introduction of reforms which radically change complex traditional patterns. It also has marked the beginning of an era in which the government has elected to undertake, as a national effort, most of the future economic growth of Peru. For the most part, large multinational mining companies, which have helped to discover and put into operation large mineral and ore deposits in Peru, have been sympathetic toward this philosophy. Most big foreign companies, in addition to capital, brought with them to Peru an efficient technology, modern management, and an effective organization for the further processing, sales, and distribution of refined commodities. Nationalization of all basic resources, including mining, is the, trend-not, it is hoped, to the detriment of established technology and production.

Jan 1, 1974

Annual Meeting,Wallace, Idaho, Nov. 15-16, 1913. The third annual meeting, which was also the eighth consecutive meeting and the second to be held in the Coeur d'Alène district, was held in Wallace, Idaho, Nov. 15-16, 1913, with side trips to Kellogg-Wardner, Larson, and Mullan, where several mills were visited. The meeting was held jointly with the Montana Section, about 50 members and guests being present. Headquarters were in the Samuels Hotel, sessions being held in the public library. The arrangements and program were in the hands of the following local committee: George W. Roddewig, W. Earl Greenough, H. M. Childs. At 2.30 p.m., Nov. 15, the first session was called to order by Prof. F. A. Thomson, member of the Executive Committee, adjournment being taken to the Mine Rescue car, where Mr. Anderson and his assistant entertained the visitors for nearly two hours by demonstrations of mine-rescue and, first-aid practice, after which the party visited the Hercules mill, mention of which was made in the report of last year when the Section visited the plant. There are, however, several important alterations and additions to the flow-sheet to be noted, such as substitution of Chilean and Hardinge mills for the Huntington mills in the regrinding department; rearrangement of the tables and slimers, with a noticeable addition of the later models of the Franz machines, and the installation of the Wyman flotation process, which has been tried out, or is being tested, with more than ordinary success, on the middlings in several of the mills of the district, the Green Hill Cleveland mill being provided with a 100-ton unit, partly described below

Jan 12, 1913

By Edgar C. Bain

In studying the structural characteristics of martensite it is desirable that a clear conception of the material from which martensite is produced should first be obtained. Any theory of its formation and structure incompatible with the facts of its parent substance, austenite, can be eliminated with little consideration. Austenite is the name applied to solid solutions of carbon and other elements in gamma iron. At temperatures above about 900" C. (1650" F.), pure iron exists in a system of crystallinity1 entirely different from the crystal structure below that temperature. This high-temperature allotrope of iron is of an atomic structure associated with great ductility, having very manifold symmetry and an abundance of easy slip planes. The exceptionally ductile and malleable metals (gold, silver, platinum, copper, aluminum, and nickel) have this same atomic arrangement— the face-centered cubic. The low-temperature allotrope of iron, alpha iron, the solid solutions of which are known as ferrite, has a body-centered cubic arrangement of atoms. Like it, in crystal structure, are the less ductile and malleable metals, molybdenum, tungsten, titanium and chromium. Fig. 1 shows the two atomic arrangements known in iron; the diagrams are drawn to scale. Either of these modifications of iron may dissolve other elements in the solid state; by so doing, the temperature of the transformation is changed. In general 2-7, it appears that a solid solvent metal dissolves a metal solute by substituting foreign atoms in its own space lattice. Thus, iron may dissolve nickel in either of its crystalline forms by permitting an atom of nickel here and there to occupy the normal position

Jan 1, 1924

By F. L. Bosqui

Discussion of the paper of F.* L. Bosqui, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 101, May, 1915, pp. 997 to 1033. SIDNEY J. JENNINGS, New York, N. Y.-I notice Mr. Bosqui says that zinc dust can be used profitably. I had occasion recently to try to ship some zinc deist to South Africa, owing to the. high price of zinc in the last six or eight months and the difficulty in getting zinc sheets We were informed that the steamship companies in England refused to accept zinc dust for shipment through the tropics on the score that it was an explosive mixture. C. W. MERRILL, San Francisco, Cal.-In the early days zinc dust was packed in wooden casks. The steamers at that time were very chary of transporting it. It was put on the deck in the wooden casks, and if the zinc dust got wet it exploded. Since that time we have used hermetically sealed cases, in which case there is no risk whatever in its transportation.. This rule of the steamship companies is perhaps another sample of their ultra-conservativeness. HENNEN JENNINGS, Washington, D. C.-Unfortunately, I have not yet read Mr. Bosqui's paper, but believing it might interest you to know something of the beginning of the cyanide process on the Rand, I will speak briefly as to my own knowledge and experience of the early initiation of this process in South Africa. I took the position of consulting engineer of H., Eckstein, the parent firm of H. Eckstein & Co., and a branch of the firm of Wernher, Belt ,C Co., at Johannesburg, in December, 1889, and at that time the Robinson Co. managed by them was the premier company of the fields. Up to this date plate amalgamation and catchment of a small percentage of concentrates by blankets, and in a few instances Frue vanners, were the main gold-saving devices used and had obtained an extraction' of only about 65 per cent of the gold contents of the ore. Also at that time the orebodies were seen to be changing from oxidized deposits to pyritic at varying depths from 50 ft. to 300 ft. below the surface, and uneasiness was felt as to future recovery. The deepest exploitation at any of the mines was not much below 300 ft.

Jan 12, 1915

By D. J. Carney, R. R. Burt, E. J. Whittenberger

Hardenability (multiplying) factors for carbon, mongonese, silicon, chromium, nickel, and molybdenum have been developed for hypereutectoid low-alloy steels in which bainite is the first subcritical transformation product. These factors permit the calculation of 95, 80, and 50 pct martensite hardenability from chemical composition when steels with spheroidized structures are quenched from 1475°, 1525°, and 1575°F. The strong contributions to hardenability of the less expensive elements, silicon and manganese, suggest their use to obtain additional hardenability in hypereutectoid low-alloy steels. DURING the past decade a number of investigators'"11 have carefully developed information which permits calculation of the hardenability of medium -carbon low-alloy steels from chemical composition and grain size. These data have been especially valuable in developing less costly low-alloy steel compositions with equivalent or Improved

Jan 1, 1957

By F. W. Davis

SOME idea may be gained of the tremendous consumption of refractories by the open-hearth steel manufacturers from a statement made by A. T. Green at a meeting reported by T11.e Industrial Chemist of London, as follows: "At a very progressive steel plant in the Midlands, with a battery of five open-hearth furnaces working. twelve months and making 3000 tons of steel per week, the cost of refractories per ton of steel produced averages about $0.50 for the actual open- hearth casting and $0.12 for those operations incidental to the rolling of the metal." .These figures, when translated into the annual tonnage of steel, represent a very considerable expenditure.

Jan 1, 1930

By Albert Sauveur

To understand this paper properly, the reader must have a clear conception of what is meant by the " critical points " of iron and steel; * and in order to avoid the necessity of tedious references to previous publications on the part of those unfamiliar with the subject, it is here briefly recapitulated. Critictl Points.—If a piece of steel containing, say, 0.50 per cent. or more of carbon, be heated to a high temperature and then allowed to cool slowly, the cooling proceeds at first at a uniformly retarded rate until a temperature of about 700° C. is reached, when there is a sudden " retardation " in the fall of

Jan 1, 1897

By D. L. Martin, E. R. Parker

DURING the heat-treatment of silver specimens for tensile tests it was observed that the bars blistered and became brittle when heated in a hydrogen atmosphere. [ ] To check this unexpected result, a wide variety of commercial silvers were heated in hydrogen at 850°C, Only a few of the materials developed blisters, the most severe of which is the tube pictured in Fig. I. The microstructure of a cross section of the tube is shown in Fig, 2. The embrittlement is extremely severe at the edge; the blisters result from the severe deforma- [ ] tion of the surface material by large underlying gas pockets, The effects resulting from hydrogen embrittlement of silver have been observed by numerous investigators over a long time1,2,3 although it was only recently that a clear explanation was offered ,4 However, the damage resulting from hydrogen embrittlement has not been generally recognized; and it is of advantage to know more about this phe-

Jan 1, 1943

By C. R. Sundeen, C. W. Nicolson, J. D. McAuliffe, C. A. Campbell, P. D. Pearson

SHAFT SINKING SYMPOSIUM is a weighty term that could mean any number of things. However, in, this case it has been possible to utilize the transcription of the Annual Meeting Session of the same title and present it in much the same manner as the experts on the panel presented it to their audience Wednesday afternoon, February 18, 1953, at the Los Angeles Statler Hotel.

Jan 8, 1953

By R. J. Pfister

The development of a water-input profile instrument based on the introduction of brine and fresh water into an input well with the electrical location of, the boundary developed between them is reported. Two methods are available in the use of this instrument to measure the foot by foot water-intake rates of the various sand strata: the moving boundary method in which variable well bore diameters can be determined and/or cancelled out and the constant boundary method. The type of results obtained and the relative advantages of each of these methods are described in detail. Representative data are included covering the use of this instrument in experiments involving selective acidizing, selective plugging, and selective shooting. In such experiments, this instrument has been used to diagnose the unfavorable distribution of water intake in input wells and also to determine the effectiveness of the resultant treatments. The data included also serve to illustrate the type of problems which can be studied with this technique. Introduction For ten years or perhaps longer a number of progressive water-flood operators have felt the need for some to to measure the foot by foot water-intake rates of various strata in water-injection wells. The primary need is to diagnose unfavorable water distribution in various strata and to evaluate the effectiveness of the corrective measures such as selective acidizing, selective plugging, and selective shooting. Previously described methods for obtaining this type of data were not considered entirely adequate.l,2 The profile equipment described in this paper embodies the separate introduction of brine and fresh water into the well at carefully measured and controlled rates and the electrical location of a sharp boundary developed between these fluids. At present this instrument is a research tool of value in determining the effect of various well treatments on an individual sand strata. lts primary use has been on wells in which different sections require different treatments (e.g., wells with an open sand to be plugged and a tight sand to be acidized)- It has, thus, made possible the determination of a rearrangement of the water intake of a well. The instrument can also be used to direct the treating material into a given zone. In completing a well the less permeable sands are shot more heavily with nitroglycerine in order to equalize the water intake between the permeable and less permeable sands. The extent to which such corrective shooting has been successful Can be determined by a water-input profile. The combined profile and well-bore diameters should also provide a method for determining the direction and effect of various selective shooting techniques. Equipment The essentials of the water-input profile technique for measuring the intake per foot of individual sand strata are the injection of a nonconducting fluid, water, at the top of the well and a conducting fluid, brine, through a separate string of

Jan 1, 1948

THE composition and quality of finished steel depend upon selection and proportioning of the raw materials of the charge as well as upon control of furnace practice. This chapter deals only with the raw materials of the basic open-hearth process that are important in determining the composition of the steel or slay. They are the metallic charge, oxygen-bearing materials, fluxes, alloying and deoxidizing additions, and certain refractory materials used for maintenance of bottoms. Other refractories, which may affect the slag composition, are discussed in Chapter 3. Wide variations are possible in the type and composition of charged materials but certain limiting relations among the elements of the charge must be observed. Since the process consists essentially of refining by the oxidation of undesired elements, a balance must be established between the sources of oxygen and the elements in the charge that are subject to oxidation (see Chapters 2 and 7). For example, if it is desired to use a high ratio of blast-furnace hot metal to scrap, it is necessary to add an oxygen-bearing material such as ore or mill scale to eliminate the excess carbon and silicon that are present in the hot metal. An example of the opposite extreme is the use of a metallic charge composed entirely of steel scrap. With this type of charge, it is common practice to substitute burnt lime for limestone as a flux and to charge some carbonaceous material such as coke to avoid an excess of oxygen in relation to the elements of the charge that are subject to oxidation. Elements such as copper and nickel, which are not oxidized or eliminated by any other reaction, may be introduced into the charge only to the extent to which they are permissible in the finished steel. An example of adjustment of the charge for elements of this type is found in the use of steel scrap high in copper. In this case, metallic components of the charge other than the scrap should be low in copper, or a sufficiently high ratio, of pig iron to scrap should be charged to dilute the copper from the

Jan 1, 1964

By R. J. Pfister

The development of a water-input profile instrument based on the introduction of brine and fresh water into an input well with the electrical location of, the boundary developed between them is reported. Two methods are available in the use of this instrument to measure the foot by foot water-intake rates of the various sand strata: the moving boundary method in which variable well bore diameters can be determined and/or cancelled out and the constant boundary method. The type of results obtained and the relative advantages of each of these methods are described in detail. Representative data are included covering the use of this instrument in experiments involving selective acidizing, selective plugging, and selective shooting. In such experiments, this instrument has been used to diagnose the unfavorable distribution of water intake in input wells and also to determine the effectiveness of the resultant treatments. The data included also serve to illustrate the type of problems which can be studied with this technique. Introduction For ten years or perhaps longer a number of progressive water-flood operators have felt the need for some to to measure the foot by foot water-intake rates of various strata in water-injection wells. The primary need is to diagnose unfavorable water distribution in various strata and to evaluate the effectiveness of the corrective measures such as selective acidizing, selective plugging, and selective shooting. Previously described methods for obtaining this type of data were not considered entirely adequate.l,2 The profile equipment described in this paper embodies the separate introduction of brine and fresh water into the well at carefully measured and controlled rates and the electrical location of a sharp boundary developed between these fluids. At present this instrument is a research tool of value in determining the effect of various well treatments on an individual sand strata. lts primary use has been on wells in which different sections require different treatments (e.g., wells with an open sand to be plugged and a tight sand to be acidized)- It has, thus, made possible the determination of a rearrangement of the water intake of a well. The instrument can also be used to direct the treating material into a given zone. In completing a well the less permeable sands are shot more heavily with nitroglycerine in order to equalize the water intake between the permeable and less permeable sands. The extent to which such corrective shooting has been successful Can be determined by a water-input profile. The combined profile and well-bore diameters should also provide a method for determining the direction and effect of various selective shooting techniques. Equipment The essentials of the water-input profile technique for measuring the intake per foot of individual sand strata are the injection of a nonconducting fluid, water, at the top of the well and a conducting fluid, brine, through a separate string of

Jan 1, 1948

By Henry N. McCarl

Lightweight aggregates include a variety of mineral and rock materials used to provide bulk in concrete building units (block), light- weight structural concrete, and precast concrete units, as plaster aggregate, insulating fill, and other structural and/or insulation purposes. They are distinguished from other mineral aggregate materials by their lighter unit weight- 80 to 100 pounds per cubic foot (pcf) or less for loosely packed lightweight aggregates as compared to 125 pcf or more for crushed stone, sand, gravel, air-cooled slag, and other more common mineral aggregates. The various lightweight aggregate materials may be classified into four groups as follows: 1) Natural Lightweight Aggregate Materials-prepared by crushing and sizing natural rock materials such as pumice, scoria, tuff, breccia, and volcanic cinders. 2) Manufactured Structural Lightweight Aggregates-prepared by pyroprocessing clay, shale, or slate in rotary kilns or on traveling grate sintering machines. 3) Byproduct Lightweight Aggregates-prepared by crushing and sizing foamed and granulated slag, cinders, and coke breeze. With the exception of processed slag, this group is becoming less important as time passes. 4) Manufactured Insulating Ultralight- weight Aggregates-prepared by pyroprocessing ground vermiculite or perlite. This chapter will focus on the use of natural lightweight aggregates and manufactured insulating ultralightweight aggregates, and both the production and use of manufactured structural lightweight aggregates with some comments on byproduct materials. Detailed discussion of the production and use of both expanded and air-cooled slag is presented in a separate chapter in the utilization section of this volume, and there are separate commodity chapters on vermiculite, perlite, pumice, and volcanic cinders. Discussion of the commodities covered elsewhere in the book will be limited to observations on their utilization and relation to other lightweight aggregate materials. All materials considered as lightweight aggregates are derived from some initial natural raw material. While historical definitions have included such organic materials as straw and peat as lightweight aggregates, the discussion in this chapter will restrict itself to lightweight aggregates derived from mineral or rock materials. Thus while the actual lightweight material in use may be a manufactured product, it is derived from an ore or raw material that is obviously a mineral resource. In this context, then, the reserves of raw materials for lightweight aggregate use may include iron ore and flux stone (the components of blast furnace slag) as well as coal (the raw material from which cinders are derived) as well as those clay, shale, and slate deposits that display the characteristics of bloating or controlled expansion when subjected to elevated temperatures (1600 to 2400°F.).

Jan 1, 1975

By E. P. Mathewson

The early development of the reverberatory furnace for smelting copper-ores was the work of the Welsh smelters, particularly those of Swansea. The first record of a reverberatory furnace is made by Jars, who states that in 1755 copper-smelting was effected .in reverberatory furnaces at Middleton-Tyas, in Yorkshire, England. The first patent, of any importance, for improvements in reverberatory furnaces was granted to Thomas Williams in 1778 for the granulation of the regulus. The next was that of William Evetts, in Sheffield, in 1812, for the cooling of the fire-bridge by the admission of air. Charge-hoppers above the furnaces were in common use in 1848. The size of the hearth of the furnaces about the beginning of the 19th century was commonly 11 by 8 feet. No material development was made until the Welsh process mas brought to Colorado, where Richard Pearce, as manager of the Argo works, near Denver, developed the furnace to meet the requirements of a custom plant, under keen competition with lead-silver smelting-plants, using blast-furnaces. His improvements are outlined in Fig. 1, elaborated by permission from E. D. Peters's excellent work,' to which the reader is referred for further details. This figure shows that the furiiaces were in 1878, 9 ft. 8 in. by 15 ft. in hearth; and in 1894, 16 by 35 ft., while the capacity of the furnace had been increased from 12 tons per 24 hr. to 50 tons in the same period.

Jan 1, 1913

By T. Lane Carter

Before describing the experience with the Chinese on the Rand and the work they have accomplished, it will be necessary, first, to give a brief account of labor-conditions in the Transvaal since the war, and then to show how the necessity of importation of labor arose. As is well known, the Transvaal mines are run on the dual system of labor—that is, the rough work is done by colored laborers under the superintendence of white men. From the start of mining operations in South Africa there has been the cry of shortness of native labor, due in great measure to the failure of Kaffirs to work continuously in the mines. While he works, the Kaffir is a satisfactory laborer, but his period of service is short, averaging about nine months. People unacquainted with the Kaffir have maintained that, by offering a higher wage and better accommodation, better results would be obtained from the native workers, but an increased wage simply aggravates the trouble. The Kaffir's wants are few. While at work Be spends little of his money, and before long has sufficient capital with which to buy wives and become a gentleman of leisure. Doubling the wage of the Kaffir means that he acquires a competency in half the time, so that his period of service is correspondingly reduced. In 1899, before the war, there was always a cry about the scarcity of Kaffir labor. The highest number of natives at work was in July and August, 1899, when nearly 100,000 were employed. At the outbreak of hostilities the Kaffirs were scattered far and near, many doing well during the war by working for the military authorities. On the resumption of mining operations on the Rand a serious mistake was made. Based on past experience, it was argued that if the whole industry decided to start anew with

Jan 1, 1909

By ERLE VICTOR DAVELER

ERLE VICTOR DAVELER, who in his application for membership in the Institute in 1909 modestly described himself as "millman," was born at Denver in 1885 and graduated from the University of California in 1907. After a few months' work at gold mills in California he went to Tonopah, where for the next two years he had a varied experience working on pumps, convey- ors, tube-mills and filters. For the following two years he was experimental foreman and metallurgical engineer for the Utah Copper Co. at Garfield. He was sent in 1911 to be assistant superintendent of mills at the Ray. From 1913 to 1917 he was mill superintendent at the striking but unsuccessful experiment in large-scale low-grade gold mining of the Alaska Gold Mines Co.

Jan 1, 1929