Search Documents

By C. D. King

THIS year the American Institute of Mining and Metallurgical Engineers celebrates its seventy-fifth anniversary as well as the same anniversary of iron and steel in this country as we now know it. The society's span of life comprehends the very beginning and gradual development of the present-day iron and steel industry and its TRANSACTIONS are rich with the trials and achievements of the pioneers in this field. It is difficult to believe that in the first year of the Institute's existence there was produced in this country only 84,000 net tons of ingots, of which only 2000 tons was made by the open-hearth process; that the bessemer process was just barely beginning; that charcoal and anthracite were virtually the only blast-furnace fuels; that Mesabi ores had not been used in blast furnaces, and such pig iron as was then made was produced at a number of small units, each adjacent to its ore and fuel supply. The growth from 84,000 net tons production of steel ingots to 95,500,000 tons in 1945 eloquently tells the story of America's industrial growth.

Jan 1, 1947

By Earl C. Smith

Jan 1, 1935

By Earl C. Smith

Jan 1, 1935

By Pol Duwez, Howard E. Martens

INTRODUCTION THE high temperatures encountered in the operation of jet engines have imposed most drastic requirements upon the materials used in their construction. There are two different approaches to the materials problem connected with the design of parts in contact with high temperature gases. The first approach is to use a material which will perform satisfactorily at a temperature comparable to that of the gas. The second approach is to use a cooling system so that the material is maintained at a temperature appreciably lower than that of the gas. Besides the conventional method .of cooling by means of a liquid in contact with the material exposed to a high rate of heat transfer, a less orthodox method consists of making the part to be cooled of a porous material, so that the cooling fluid can be forced through the pores. In this scheme, the temperature of the coolant moving in a direction opposite to that of the heat flow increases gradually while passing through the porous material, and the coolant forms a protective layer on the surface exposed to heat. This method, referred to as "sweat cooling," was proposed at the jet Propulsion Laboratory in September 1944, and the experimental work on the preparation of porous metals was started early in 1945. The sweat cooling method opens new lines of research in powder metallurgy by extending the field of application of porous metals. The porous metals available at the present time are used mostly as bearings or filters, and a rather limited number of alloys are made for these applications. In addition, the fabrication of bearings or filters does not require a very dose control of the permeability, while in the case of sweat cooling such a control is of primary importance. In designing a sweat cooled part it is imperative to assure a given rate of flow of coolant under certain conditions of pressure drop. Generally, the proper pressure drop and the rate of flow of coolant are deduced from heat transfer and design considerations, and consequently the permeability of the porous metal to be used is also determined. It is therefore necessary for the designer to have available a continuous series of porous metals covering a range of permeability as wide as possible. Contrary to the requirements established in the fabrication of filters, the actual pore size of a porous metal intended for sweat cooling is of little consequence, except for its effect on permeability. The tensile strength is likely to be of great importance for some applications. Since the tensile strength of a porous alloy decreases with increasing porosity, an important problem is to develop porous alloys having the maximum permeability with minimum porosity.

Jan 1, 1948

By N. D. Shutler

This paper describes a numerical mathematical model of the steamflood process that depends on fewer restrictive assumptions than models previously reported. The solution, however, is obtained economically. Example calculations are presented that, on comparison with experimental results, tend to validate the model. Results that expose certain process mechanics are discussed. The model describes the simultaneous flow of three phases — oil, water and gas — in one dimension. It includes the effects of three-phase relative permeabilities, capillary pressure, and temperature- and pressure - dependent fluid properties. Interphase mass transfer of water-steam is allowed, but the oil is assumed nonvolatile and the hydrocarbon gas insoluble in the liquid phases. The model allows heat convection in one dimension and two-dimensional heat conduction in a vertical cross-section spanning the oil sand and adjacent strata. The hydrocarbon-steam gas composition is tracked, but the effect of gas composition on water-steam phase behavior is neglected. The model is solved numerically in three separate stages. The three-phase mass balances are solved simultaneously using Newtonian iteration on nonlinearities occurring in the accumulation terms. The energy balance is solved separately by noniterative application of the alternating-direction implicit procedure. Separate solution of the composition balance is accomplished by straightforward solution of the finite difference equations. The method of effecting nonsimultaneous, stable solution of the mass and energy balances is the key to the success of the model. INTRODUCTION Mathematical tools as well as laboratory and field experiments are necessary to help us understand the complex steamflood process. A mathematical model can expose process mechanics and show the relative importance of process variables, but this ability is often limited by restrictive assumptions. Most known models of steam processes,l-5 with the exception of the model of Gottfried,6 are "simplified" in that they involve analytic approximations and require many restrictive assumptions. The primary utility of these methods lies in the routine use as an aid in engineering design. By contrast, the comprehensive model presented here is numerical and requires far fewer restrictive assumptions. It finds its primary utility as a research tool. It serves as an aid in understanding the nature of the process, in interpreting laboratory experiments and in evaluating and developing simpler mathematical models for engineering design. The major reason why previously presented models have been confined to the "simplified" class is evidenced by the one published exception. In 1965, Gottfried6 presented a numerical model for the combustion process of which the steam process is a subset. The result is a comprehensive tool (though it neglects capillarity and two-dimensional heat conduction) that is troubled with convergence problems and that requires 2 to 3 hours of IBM 7094 time to complete a calculation. Though our present model does not simulate combustion, it does consider capillarity and two-dimensional heat conduction and it overcomes the convergence and computer-time problems. MATHEMATICAL DESCRIPTION OF STEAMFLOODING FLUID FLOW The equations employed to describe three-phase fluid flow are of a familiar form. Darcy's. law provides expressions for the velocities of the three phases (oil, water and gas), which, when combined with oil, water and gas mass balances, give the partial differential equations governing flow of the

Jan 1, 1970

By P. F. Gnirk, J. B. Cheatham

Single bit-tooth penetration experiments under static load were conducted on six rocks at confining pressures of O to 5,000 psi using sharp wedge-shaped teeth with included angles ranging from 30 to 120° In general, the force-displacement curves for all rocks exhibit an increasingly nonlinear and discontinuous behavior with decreasing confining pressure. The confining pressure at which a rock exhibits a macroscopic transition from predominantly ductile to predominantly brittle behavior during penetration vmies from about 500 to 1,000 psi for the limestones to greater than 5,000 psi for dolomite. The correlation between calculated values of force per unit penetration based on plasticity theory and experimental values is quite encouraging, even at confining pressures as low as 1,000 psi A qualitative correlation between volume of fragmented rock per unit energy input for a single bit-tooth and drilling rate for microbits appears to exist over a confining pressure range of 0 to 5,000 psi. INTRODUCTION Laboratory experiments utilizing a small-scale drilling apparatus have demonstrated that penetration rates are reduced considerably as a result of increasing the confining pressure from atmospheric to a few thousand psi?-3 This undesirable situation can, in general, be attributed to a combination of decreased efficiency of chip removal at the bottom of the borehole, increased rock-failure strength, and a possible change in the mechanism of chip generation and rock fragmentation with increasing confining pressure. To more fully understand the principles underlying the last circumstance, it is the purpose of this investigation to experimentally study the mechanism of single bit-tooth penetration into dry rock at low confining pressures and, in particular, to establish the confining pressure at which the penetration mechanism may undergo a brittle to ductile transition for various rock types commonly encountered in drilling. Confining pressure as used here refers to the differential pressure between the borehole fluid pressure and the formation-pore fluid pressure. EXPERIMENTAL PROCEDURE Using an experimental apparatus previously described: a single, sharp wedge-shaped tool was forced under a "statically" applied load into an effectively semi-in finite dry rock sample subjected to a prescribed confining pressure. To prevent the invasion of the con fining-pressure fluid into the pores of the rock sample during penetration, the exposed surface of the rock was jacketed with a layer of silicon putty.* Electrical instrumentation incorporated into the apparatus yielded a graphical plot of force on the tool as a function of penetration or displacement of the tool into the rock during an experiment. During the course of the experimentation the following conditions were maintained constant: (1) pore pressure — atmospheric (i.e., the rock was dry); (2) temperature — 75F; (3) rate of loading — essentially static (approximately 0.002 in./sec); (4) bit tooth — a sharp wedge-shaped tool loaded normal to the rock surface; (5) rock surface — smooth and flat; (6) drilling fluid — hydraulic oil; and (7) maximum depth of penetration — approximateiy 0.1 in. In addition, each experiment was performed on a different rock sample so the rock surface is free of a layer of cuttings and of any previous indentation craters. The influence of the corners of a borehole was neglected, since each rock sample was cemented inta a section of aLuminum tubing to simulate a semi-infinite body. Indentation experiments were made on a sandstone, two limestones, a marble, a dolomite and a schist with a 60' bit-tooth over a range of confining pressures from atmospheric to 5,000 psi and at a constant confining pressure of 1,000 psi for a variety of bit-teeth with angles ranging from 30 to

Jan 1, 1966

By Joseph W. Roe

MANY questions arising in the work of the mining engineer may be solved quickly and with sufficient accuracy by the methods of descriptive geometry; but, unfortunately, this subject is more often considered from a mathematical view-point than as an effective tool. for solving practical problems. Some of the principles involved are merged into the ordinary operations of mechanical drawing, and are used unconsciously by the engineer in his every-day work. The rest are stowed away on the book-shelf with his forgotten or rarely-used college text-books. One reason for this condition of "innocuous desuetude " may lie in the unfortunate and often cumbersome notation which it has been found necessary to introduce. If some of these principles can be recalled to the engineer's attention in terms of every-day use they may prove of practical bearing. Recently, in talking with several mining engineers, I used some of the drawing-room methods of a machine-designer, to the evident surprise of those around me. These men were perfectly familiar with the methods, but their application to mining-work had not occurred to them. At their suggestion the present paper is offered, not in any way as a treatise, but merely to suggest a certain point of view, in hope that it may lead others far more familiar with mining-problems to pursue the subject further. I. To FIND THE STRIKE. As the simplest and most fundamental problem, let it be required to find the strike of a vein when the location and elevation of three points on the outcrop are known. It will be assumed for the present that the vein is a plane.

Mar 1, 1910

By W. G. Matteson

The Oklahoma legislature recently passed a bill providing for "the creation of an oil and gas department under the jurisdiction of the Corporation Commission, authorizing the Corporation Commission to appoint a chief oil and gas conservation agent, and conferring exclusive jurisdiction on the Corporation Commission in reference to the conservation of oil and gas, and the inspection of gasoline and oil, the product of crude petroleum, and repealing all acts or parts of acts in conflict therewith and declaring an emergency." Some of the functions of the new bureau include the receiving and filing of all well logs, and the direction and supervision of plugging all abandoned oil and gas wells, under rules prescribed by the Corporation Commission. The two leading petroleum-producing States of the country, Oklahoma and California, have now established oil and gas bureaus with a staff of inspectors to see that the important rules relating to the conservation of oil and gas are thoroughly enforced. The economic significance and the value of well logs in the conservation work has been recognized, and the necessary legal action taken to insure and procure them. William B. Heroy, of the Government Land Classification Board, in a personal communication to the writer, says that the drilling of wells is also regulated by public authority in the Roswell artesian basin in southeastern New Mexico, where a permit must be obtained for the drilling of any well and a certified log of the well recorded with a county official. The method is said to give fairly satisfactory results. In a recent article1 a National instead of a State Bureau was suggested for collecting and filing well logs. In discussing the paper, L. L. Hutchison characterized such a plan as impractical because the average driller or contractor will often juggle or guess at the log and will not keep the record sufficiently close or accurate, making it necessary to maintain a special man at each well for the sole purpose of obtaining

Jan 1, 1918

By Enrique Hauser

FiRE-damp is a mixture of methane with other inert gases or combustible gases. The inert gases in question are carbonic acid, water vapor, nitrogen, etc. The combustible gases are hydrogen, ethane, etc. The study of the properties of fire-damp, therefore, becomes a study of the properties of methane and the influence on its properties of the different gases we have mentioned. Characteristic Properties of Methane 1. Respirability.—Methane being a paraffin is characterized by its weak chemical affinities. Prom the physiological point of view one could substitute it for nitrogen of the air at least momentarily, without experiencing any difficulty in breathing the mixture consisting of 21 per cent. 02 + 79 per cent. CHI. I have tried this on myself, making the gas exhaled from the lungs burn subsequently in a Bunsen burner.' From the chemical point of view, this weak affinity permits the gas to be burned in certain circumstances with hydrogen and oxide of carbon in an oxygenated mixture, with the result that the last two gases achieve only a fractional combustion. This practice has been utilized with success in the methods of analysis which I have perfected and which I describe later in this paper. 2. Retardation of Flashing Point.—A characteristic property of methane is its retardation of flashing point, noted by Davy in 1816 and studied by Mallard and Le Chatelier in 1883.2 Taffanel and Le Floch have recently confirmed these results.8 Let us recall the nature of this retardation: When a mixture of combustible gases with air or with oxygen is

Jan 1, 1916

Jan 1, 1951

By A. Muan

Liquidus data are presented for mixtures in the ternary system FeO-Fe2O3-SiO2 in equilibrium with a gas phase with O2 pressures ranging from 10-10.9 to 1 atm. Data obtained are combined with previously published data to construct lines of equal 02 pressures and lines of equal CO2/H2 mixing ratios along the liquidus surface. Courses of crystallization of selected mixtures under conditions of constant total composition, constant O2 pressures, and constant CO2/H2 mixing ratios are discussed. PHASE equilibrium studies of silicate systems where iron is one component are complicated by the fact that iron readily occurs in three different states of oxidation: Fe3+, Fe2+, and Fe0. Success or failure in work with iron silicate systems is to a large extent dependent on control of the oxidation state of iron and all investigations therefore must be carried out under carefully controlled atmospheric conditions. Silicate systems containing only strongly electropositive metals (like Na+, Ca2+, Mg", etc.) can, for simplicity, be treated as condensed systems, that is, the gas phase can be neglected and the phase relationships discussed in terms of the phase rule written in the well known simplified form P + F = C + 1. In the case of iron silicate systems, however, the composition of the condensed phases varies with the gas composition, and a complete picture of phase relationships can be obtained only by varying the gas composition over a wide range. In order to understand the phase relationships in the more complicated multicomponent silicate systems with iron oxide as one of the constituents, a knowledge of the ternary system FeO-Fe2O3-SiO2 is essential, since it constitutes a bounding portion of all such systems. It was with this in mind that the present study was undertaken. Previous Work A considerable amount of work has been done on various aspects of the chemistry and metallurgy of systems containing silica and iron oxides. The two bounding binary systems FeO-Fe2O3 and FeO-SiO2" The first attempt to obtain information on phase relationships of iron oxide-SiO, mixtures at different 0, pressures was made by Greig.' Darken" determined the melting points of iron oxide on solid silica under various atmospheric conditions. Darken did not determine experimentally the composition of the melts at liquidus temperatures but discussed very ably the principles involved in applying the phase rule to the system. In a recent study Schuhmann, Powell, and Michal8 determined experimentally the liquidus surface of a portion of the ternary system and combined the new information with data in the literature to construct a phase diagram. Their method was briefly as follows: Homogeneous mixtures with various contents of SiO2, FeO, and Fe2O3 were made up by melting together stock mixtures in various proportions. Samples of the homogeneous mixtures, the compositions of which were determined by chemical analysis, were then heated in platinum crucibles in an inert atmosphere until equilibrium among the condensed phases was achieved. The samples were quenched to room temperature and the phases present determined by microscopic examination. Assuming that no change in composition takes place during the equilibration run in inert atmosphere, the liquidus surface can be determined, but no information is obtained regarding the partial pressures of 0, of the gas phase in equilibrium with the condensed phases. The author's method, to be described in the next section, permitted the location of points at the liquidus surface as well as a calculation of the corresponding partial pressures of O2. Experimental Method General Procedure: The standard quenching technique was adapted for a study under controlled variable atmospheric conditions. Premelted mixtures of silica and iron oxides in platinum envelopes were held at constant temperature under chosen atmospheric conditions until equilibrium was reached among solid, liquid, and gas phases. The sample was then quenched to room temperature, the phases present identified, and, for the most significant runs, the composition was determined by chemical analysis. The corresponding partial pressure of 0, was calculated from known equilibrium constants of the gas reactions occuring in the furnace atmosphere. Materials: Starting materials were oxides of commercially highest available purity; cp silicic acid was dehydrated by heating to 1350°C for 6 hr and cp Fe2O3 was dried at 400° C for the same length of time. Samples of 10 g were made up by mixing

Jan 1, 1956

The early Spanish adventurers found but little gold or silver on the American mainland, and the aborigines in the country that is now the United States were not as submissive as those of the West Indies, so the conquistadores obtained no foothold north of the Caribbean sea. Their later exploration north- ward had Mexico as a base-and wild yarns as a basis. The friar Marcos, a member of Estevanico's unfortunate expedition, brought the story of the Seven Cities of Cibola to Mexico City in 1539. Except as Indian hovels,* they existed only in a disordered imagination, but when Váquez de Coronado's expedition pricked the glittering bubble, there appeared an enticing mirage in the northern desert: the glorious land of Quivira, where even-the common pitchers and bowls were made of solid gold. Coronado proceeded northward and found only enormous herds of buffalo on the plains of Texas. It was a melancholy land. No gold or silver was to be seen among the poor Indians. Coronado reached the country of the Wichitas, in Kansas, before he abandoned his quest and turned home, which he reached, with only a third of his party, hungry and tattered, in 1542. So long as greed stimulates the imagination there will be no lack of tales such as those that repeatedly led the Spaniards to the rainbow's end. In 1860 an expedition was organized in San Francisco by Dr. Darwin French to explore the desert country near Owens lake on the news that the Indians in those parts shot golden bu1lets.t The fact that the savages were known to possess few guns did not discredit the tale, which

Jan 1, 1932

By Carl F. Dietz, Dyke V. Keedy

The problem of drying ores is one that most mill-engvineers are sooner or later called upon to meet, and it may be timely to point out some of the difficulties resulting from such operations from purely a metallurgical and economic standpoint. We mean, in the following pages, to discuss primarily the effect of such operations on the ore. itself, without particular reference to the mechanical or cost features of the subject. That an appreciable tonnage of the ore fed to the usual form of drier, either rotary or stack, is lost, is fairly well appreciated, but we believe that only a few mill-managers know just what their drier-losses amouilt to, and we have found that in most cases they console themselves with the fact that the drier-smoke is not very much discolored, and it is generally believed that the draft is not sufficient to carry away more than a negligible percentage of the values.

Jan 1, 1913

By J. B. Austin

In considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these efficiencies are more useful than others, yet all are instructive; for a knowledge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been caleulated without due regard to the thermodynamic principles involved. Moreover, so far as the author is aware. no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By J. B. Austin

In considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these efficiencies are more useful than others, yet all are instructive; for a knowledge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been caleulated without due regard to the thermodynamic principles involved. Moreover, so far as the author is aware. no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By Gealy W. Wallwork

INTRODUCTION The administrative processes of coal mines are becoming increasingly complex. As society evolves into a more complicated structure with greater emphasis on individuality, government regulations reach deeply into every activity in an effort to force individuals into a standardized mold. These contradictory pressures add an extra burden to the administration of a mining operation. Recent years have brought a substantial change in the skills needed by mine supervisors and managers. As a result, a better understanding of the administrative functions is necessary. The mine superintendent has the overall responsibility for the mine; for effective operation he must be sufficiently knowledgeable to oversee all the complex functions that make up the mine. This chapter does not cover all the administrative requirements because of the variation in mine operation and in company policies and organizational structure. It does attempt to identify the administrative functions that would be required at a large mine with a preparation plant. It is assumed that the mine operation is decentralized with very little duplication of functions at the organizational levels above the mine. Thus each function is assumed to be relatively complete at the mine and under the general supervision of the mine superintendent. EMPLOYMENT PROCEDURES Throughout the mining industry, in deep or surface mining, in union or nonunion companies, the success or failure of an organization is directly related to the caliber of employees who make up the organization. A company is nothing more than a group of people working together with

Jan 1, 1981

By George W. Sargent

For the experiments here described a rod was used, 0.75 in. in diameter, and rolled from one ingot. Analyses of the ingot and rod showed them to have the following composition respectively: C. Mu. Si. P. 8. Percent. Percent. Percent. Percent. Percent. Ingot,. .. 1.150 0.328 0.223 0.020 0.016 Rod,. .. 1.033 0.327 0.223 0.020 0.016 Pieces 4 in. long were heated to various temperatures in a closed porcelain tube, within a gas furnace, and allowed to cool with the same; they were then turned, threaded, and subjected to physical tests in a Riehlé testing-machine. The elastic limit was determined by the drop of the beam. The elongation was measured in two inches. From the threaded ends of the testrpieces, disks were cut, and prepared by combined polishing and etching, using parchment stretched over a wooden block and moistened with a 2-per cent. solution of ammonium nitrate. The structure, as thus developed, and the fractures, were magnified and photographed. A cooling-curve was constructed, and the critical point was located at 675º-680º C. A thermo-electric pyrometer was used to make the measurements of temperature. The micro-constituents of steel have been so frequently and thoroughly described by others that I need only say here that the theoretical micro-structural constituents of this steel were : pearlite, 95 ; ferrite, 0 ; cementite, 5 per cent. The quenched metal would be expected to consist almost entirely of martensite—provided, however, the quenching be done at or near the proper temperature. Rapid quenching from a high temperature would give rise to austenite.

Jan 1, 1902

By Orville R. Lyons, A. C. Richardson

DURING the past few years there has been a growing demand by coal operators for detailed information about the performance characteristics of the various dryers now being manufactured, preferably in such a form that the information could be used to determine the type of dryer best suited to a particular drying problem. A few operators have been desirous of going even further, because they are of the opinion that present-day dryers are not properly designed and that fundamental studies of dryer design should be undertaken. This growing demand for a method of dryer evaluation and the indicated need for fundamental research resulted in the sponsorship by Bituminous Coal Research, Inc. of a project at Battelle Memorial Institute to investigate the thermal drying of coal. In investigating this problem, the most feasible method of attack appeared to be a survey of active operations to determine the present status of the thermal drying of coal. Data were obtained, usually by actual plant tests with the cooperation of the various preparation engineers and their staffs, for Q screen-type dryers, 8 rotary- type dryers, 3 continuous-pallet-type dryers, 2 flash-type dryers, I tray-type dryer, and I cascade-type dryer. The testing program provided: (I) data for 24 coal- drying operations, (2) information about dried, (3) information about the previous treatment that the coal had received, and (4) information about operating costs. The data obtained through the dryer survey and relationships determined from the data make it evident that all of the types of dryers included in the survey can be operated with the same degree of effectiveness if each type of dryer is used to dry the sizes of coal for which it is best suited. It should be noted that it is usually undesirable and often impossible to dry different sizes of coal in one type of dryer. By use of the data in the report, any prospective dryer user, having determined the surface moisture percentage and screen- size analysis of the coal to be dried, the tons of water to be removed per hour, and the final surface moisture percentage desired, should be able to determine with a fair degree of accuracy: (I) the difficulty of the drying problem, (2) the approximate cost of drying, (3) the required dryer inlet gas temperature and volume and exhaust gas temperature and volume, (4) the type of dryer to use, and (5) the size of dryer required. The method of testing the dryers and determining the difficulty of drying can be used by operators already having dryers to check the performance of their particular dryer and determine whether they are operating effectively. Considerably more information was obtained from the survey of thermal drying than was anticipated when the survey was first considered. However, a great deal of work still remains to be done in the field

Jan 1, 1948

By T. R. Graham, J. R. Long

This report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau's War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. Preliminary Work In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, o to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944

By J. R. Long, T. R. Graham

This report is concerned with part of a series of investigations carried on by the Federal Bureau of Mines on alloys, particularly nonferrous alloys, made with electrolytic manganese. A broad general program instituted after commercial quantities of electrolytic manganese became available was necessary in order to compare the effects of electrolytic manganese with those of the ordinary commercial grades. Representative analyses of these two materials show the commercial manganese metal to contain up to 2 per cent iron, a maximum of I per cent silicon and 0.06 per cent carbon, while the electrolytic manganese rarely exceeds 0.01 iron, 0.02 sulphur, with no silicon or aluminum. In the literature, the emphasis has been largely on high-strength casting alloys containing up to 5 per cent manganese, and few data are available on wrought manganese alloys. These factors, coupled with the strategic position of copper and zinc, have given impetus to the Bureau's War Research Program for the development of alloys containing nonstrategic manganese for the purpose of supplementing or providing alternates for the more strategic metals. The alloy reported here was studied, along with several other ferrous and nonferrous alloys, as possible cartridge-case material, and was chosen after a review of the properties of the ternary alloys of copper-manganese-zinc. Preliminary Work In a cursory survey of this system, alloys ranging from 60 to 95 per cent copper, o to 50 per cent manganese, and 5 to 40 per cent zinc were investigated. The alloys containing 60 per cent copper were found to fall into the two-phase alpha plus beta region of the system, and since those containing 70 per cent would not permit a saving, only alloys containing 65 per cent copper were considered. The tensile properties of these 65 per cent alloys are plotted in Fig. I as a function of manganese content for annealed material and for four conditions of cold-work In the annealed condition the increases in strength and decreases in elongation are minor up to 15 per cent manganese; beyond this, the changes become more significant. In the cold-worked condition, the first 5 to 10 per cent of manganese appears to have the greatest strengthening effect, the rate of increase dropping off as the manganese increases beyond this amount. These effects are more pronounced with moderate than with severe cold reduction. It is also interesting to note that while the elongation of annealed material drops regularly with increasing manganese, the elongation in the cold-worked state is relatively little affected by increasing manganese content, particu-

Jan 1, 1944