Search Documents

By Henrique Silva Furtado

Concerning production of low phosphorus steel critical grades at ArcelorMittal Tubarão site, bottom blowing system plays a very important role. For those systems with independently controlled tuyeres, some non-uniform bottom blowing patterns seem to be promising in improving metal-slag mixing; however, based on computational fluid dynamics (CFD) results of ArcelorMittal Tubarão’s post oxygen bottom blowing, this may not be generalized. Also, from industrial trials it became clear that higher the bottom blowing flow rate, the closer were the end point P to the equilibrium. Despite this result an analysis of the apparent mass transfer coefficient has shown a week correlation with the classical power stir correlation suggesting a more complex kinetic limiting step for phosphorus removal.

Jul 30, 2018

By Guilherme Liziero Ruggio da Silva

Uma marcha estável do alto-forno (AF) está ligada à consistência das propriedades químicas, físicas e metalúrgicas das suas matérias-primas (MP), especialmente, as do coque. As propriedades do coque são reflexos das propriedades dos carvões que lhe deram origem. Em termos de propriedades ligadas à natureza do carvão, a qualidade do coque é bastante influenciada pelo rank dos carvões, que compuseram sua mistura, ou seja, quantidades de macerais reativos e inertes, bem como suas propriedades coqueificantes, que é, exatamente, a habilidade inerente aos carvões aglutinantes de quando aquecido, amolecer, tornar-se plástico e solidificar em uma massa coerente. Neste contexto, o presente trabalho se propõe a evidenciar as mudanças no modelo de britagem de carvões da Gerdau Ouro Branco, bem como a operacionalização do padrão criado. Após a implantação, verificou-se a elevação de 1.8% em DI.

Aug 17, 2017

By Patrick Hansert

Safety was always in the focus of Badische Stahlwerke, however at the same time productivity has to increase as well in order to compete in a tough world market. In 2015 BSW produced over 2.2 Mio tons with two EAFs, leading to tap-to-tap times in average of under 40 minutes. Our philosophy has always been, that our most important success factor are the people: therefore we have to improve the working conditions as much as we can. Starting in 2012 Badische developed a robot that can support this goal. The first step was to use it for temp/sample taking, but the unit had to become a multi-tasker. Only 2 years later the first automated cartridge changer was installed at a customer site in Scandinavia, in late 2015 then the next tool was implement: tool changer allows now to use also a camera to check the condition inside of the heat after tapping. More tools are designed currently and will be implemented shortly. This paper describes the current installations and experiences as future applications.

Aug 17, 2017

By José Aparecido Pereira

The innovative methodology developed by the author allows the elaboration of an Angle Roll Pass Design based on the practical observations of the rolling process and applies mathematical criteria, using the Ekelund´s formula supported by Advanced Excel tools (Reach Goal, PROCV-PROCH, Macros) and AutoCad. The first step is the definition of the number of stands, roll dimensions, gear boxes reduction, initial stock, average reductions, spread factors, finishing speed and type of grooves. For each pass are calculated: bite angle, spread, section reduction, lost and gain of temperature, separating force, speed, torque and motor power. After these calculations and checking of the parameters, the program calculates the dimensions of the passes transforming the flat passes into shaped ones. With these dimensions it is possible to draw the grooves using AutoCad and check section reductions. This methodology was already used for the development of a new project and also to check the parameters of existing ones, with comparison of the results and has shown to be reliable in real and tested projects. It is an innovative process that is not available in known literature.

Oct 1, 2019

By Fernando Henrique Gomes de Souza

Techniques which use a spring to supply the bias force to actuator are well adopted since they are inexpensive and simple to construct. In this work it was design an actuator concept using bias-type device technique, which comprises two coils that mutually push against each other to supply the stroke. For the coils springs, it was used a wire of NiTi shape memory alloys (SMA) and a wire of 400 grade maraging steel as construction materials.

Aug 8, 2018

By Ernst Lindemann

The SMS group has developed the ultrasound technology “HD scan” for inspection of the internal quality of as-cast products. This method of sample analysis requires less preparation work and is safer than the current, most common technique of etching and/or sulphur printing. Furthermore, this technology offers a three-dimensional view into the sample of the cast product and thus more representative information for a better quality evaluation. The internal quality evaluation can be performed automatically and objectively by software based on clear statistical methods. A quantitative centerline segregation rating can be assigned to each sample, based on the size and distribution of segregates detected by the unit. Internal crack statistic (length, position, orientation, etc.) and narrow side profile can also be measured. Grain macrostructure can also be visualized which allows for a potential optimization of casting parameters like strand cooling, soft reduction or electromagnetic stirring. The accuracy of the new method was proven by parallel metallographic investigations of more than 100 samples of different steel grades and sample shapes. Automatic defect evaluation and classification was compared against macroetching results. It was found that HD scan identified more defects and the visualization of the macro structure could be performed in more cases than with macro etching. All tests, comparisons, further developments and analyses for various steel producers and steel treatment companies have been conducted at the HD scan unit, located at the SMS group headquarters in Düsseldorf, Germany (Figure 1). Based on the results, SMS group has designed a unit which can be used in industrial scale.

Aug 17, 2017

By Renato Cortes, Claudia Lopes, Ewerton Campos, ALEXANDRE CALDELLAS BARBOSA

São diversas as razões para se utilizar a realidade virtual (RV) em treinamentos, dentre elas pode-se destacar a redução de custos, redução de riscos ao ambiente e envolvidos e também a possibilidade de reproduzir ou simular situações impossíveis, muito complexas ou ainda em outro lugar ou até mesmo em outro espaço temporal. Nesse trabalho será apresentado um estudo exploratório sobre o uso de RV, realizado uma pesquisa de mercado e apresentado o estudo de caso de como a ArcelorMittal Tubarão vem trabalhando essa tecnologia nos seus treinamentos corporativos no ano de 2019. A aceitação da tecnologia pelos empregados nos treinamentos foi acima de 98% e também foi demonstrado que além de aumentar a atratividade e a retenção do conhecimento, os ganhos foram ligados também a redução de riscos, redução de tempo de treinamento, experimentação de situações críticas, redução de custos, ou seja aumentou a eficiência e eficácia do treinamento.

Oct 1, 2019

By Antonio Augusto Gorni, Kenji Camey, José Herbert Dolabela da Silveira

Recently several studies have been developed on the use of microalloyed steels with low Mn content (below 1%) in the controlled rolling of heavy plates for the manufacture of pipes. However, this novel concept of alloy has peculiarities in its thermomechanical processing. Lower Mn contents should lead to the acceleration of NbCN precipitation kinetics during rolling, leading to a reduction in the soluble Nb content in austenite that delays its recrystallization by drag effect. This fact, plus the heavy and fast passes applied under virtually isothermal conditions in a heavy plate rolling mill with high power, increases the risk of partial recrystallization during the finishing stage of the controlled rolling, since strain hardening of austenite becomes significant and the interaction between precipitation and recrystallization is increasingly delayed. The objective of this study was to analyze the evolution of mean flow stress during the finishing stage of controlled rolling in these low Mn, high Nb microalloyed steels, in order to better understand the metallurgical mechanisms acting during this process and identify conditions that allow full compliance with the requirements of this product class.

Oct 1, 2019

By Ivan César Lopes Diniz

Stretcher Reducing Mill (SRM) is a mill used in production of tubes. It is composed with a set 24 of stands responsible to define the final outside diameter (OD) of tubes. External appearance is critical in this process even though this requirement has no effect on mechanical properties. For this reason, an investigation of external longitudinal marks mechanism is in progress using 6 Sigma methodology. This paper is a part of the investigation with focus on the rolls and its mechanical properties. Destructive tests were performed in the rolls and compared with the project. After a detailed investigation, it was concluded that rolls were out of hardness specification and the project was poor of information. A new supplier was developed (internal market) based on the new project and all requirements were achieved as demonstrated in this paper. A monopolistic market for this product in VSB (Vallourec Soluções Tubulares do Brasil) was eliminated. Concerning the effect on the external longitudinal marks, the new rolls developed within hardness range minimized the mechanism of wear on rolls surface and consequently on tubes surface. A collateral effect has been faced, but still better than external longitudinal marks on tubes surface. The quenched and tempered rolls are more sensitive for process variation, mainly linked with cooling system and temperature of tubes (mechanical resistance for deformation). Nevertheless, a new material has been aimed focusing on reduction of rolls breakage with good tenacity and affordable cost.

Oct 4, 2019

By Marco Túlio Santiago Ferreira, Nilton Carlos Torquato, Washington Pirete da Silva

In 2005, with the significant reduction of iron content in the “Quadrilátero Ferrífero” reserves, Vale began the study of alternatives for the tailings disposal in other structures, that are not tailings dams. In 2011, after bench-scale and pilot-scale tests, it was defined to implement the project "Alternative methods for tailings disposal", including the construction of experimental drainage piles to get mineral and geotechnical process parameters for future projects. The result of this study shows that it is technically possible to replace traditional tailings disposal (dams), to dry stacking, with the proportion up to 20% of ultrafine tailings in the total tailings composition, however, this study is in evolution and the scale of the project / pile is being gradually increased to guarantee a good performance for the mineral and geotechnical process.

Oct 3, 2019

By Liao Jianfeng

The Baosteel Zhanjiang 5,050m3 blast furnaces have been built with highly independent integration and innovation technologies and represented the state of the art of the world’s huge BFs. The proper of BF1 and BF2 is designed with long-campaign technology; both BFs share the same set of stockhouse, water and PCI systems; the BCQS serial-hopper no-bell top, TRT and blower are all local equipment as applied; four top-combustion stoves systems are matched; the BFG is cleaned by fully dry process; and the automation control system for the main process is self integrated. The BFs have been started up and performing with sound indicators. Their smooth proceedings symbolize China’s huge blast furnace ironmaking technology ascending a new high.

Oct 30, 2017

By Nelson SOUTO, Nicolas LEGRAND, Sami ABDELKHALEK, Zafer KOONT

A work roll thermal crown model has been developed for a wide range of hot and cold rolling mill applications. The model is extremely fast, robust and accurate to determine the evolution of thermal crown all along the rolling campaigns. It has also ability to consider work roll shifting, multiple segmented cooling zones along the length and circumference of the roll as well as composite rolls properties (e.g. different thermal properties between mandrel and core of the roll). Moreover, the model includes simultaneously fast and slow temperature evolution calculations, respectively near roll surface (skin area) and at a certain distance below the roll surface (bulk area). This gives to thermal crown predictions a higher accuracy than conventional thermal crown models from literature that consider only the slow temperature evolution regime. An optimization procedure together with roll surface temperature and roll thermal profile measurements have been used to tune the model. The tuned model applied to hot rolling conditions has shown a significant influence of roll shifting and composite rolls properties on the prediction of roll temperature distribution and thermal crown during rolling. The tuned model applied to cold rolling conditions highlights the importance of mill operators practices to modify cooling distribution across roll barrel length with the segmented cooling zones to adjust the thermal crown and to get better strip shape control.

Oct 1, 2019

By Shaney Gonçalves Mileipe

No contexto atual, os estudos de engenharia de confiabilidade se tornaram cada vez mais essenciais para o acréscimo de disponibilidade das plantas e estabilidade operacional. Este trabalho tem por objetivo, através da metodologia de análise e solução de problemas (MASP) focada em modos de falhas prioritários, reduzir o tempo de manutenção não planejada do processo de Sinterização da Arcelor Mittal Tubarão. Os resultados obtidos concretizaram um aumento de 2% na disponibilidade da planta após a elaboração de um plano para corrigir os modos de falhas críticos, revelando a importância e o potencial de ganho em se investir em estudos de confiabilidade e registro de falhas.

Oct 30, 2017

By Wellington Ribeiro Moreirar, Anderson Willian Henrique Santini, Lívia Mara Cândido, Adriano Raimundo Totour

Rejects generated in mining projects usually do not have associated economic value. Most of the ore beneficiation processes occur by wet process with a higher fraction of water and ultrafine granulometry, which makes it difficult to dispose of these wastes. In 2013, studies with new tailings treatment and filtering technologies were initiated with the objective of eliminating the disposal of the residue generated in the industrial process to wet in dams. In this context, we tried to evaluate an alternative for the dewatering of the sludge and the tailings, aiming at their disposal in piles. Essentially, we sought to consolidate the application of the high-pressure filtration technology for the effluent dewatering, in order to allow its transport and its disposal in a sustainable way. The studies performed in a pilot filter showed good performance and allowed the industrial implantation. The studies and geotechnical indications of composite tailings (flotation and sludge) make it possible to dispose of the tailings in piles due to their better values of humidity, which allows them to be safely stacked.

Oct 3, 2019

By Benito Barbabela Silva, Michel Garant, Mathieu Dubé

Pellets market challenging scenario has stimulated pelletizing experts to pursue innovative alternatives to process development in order to increase pellets competitiveness vis-à-vis sinter. When it comes to indurating process, pelletizing productivity is still limited and its OPEX inflated by the lower input of carbon into mixes due to quality impairment caused by magnetite formation in pellets core. This obstacle led to the rethinking of carbon distribution strategy within the green balls. To achieve such purposes, COREM through its precompetitive research program dedicated to its members, has proposed the layered pellets®, a two-stage balling technology. Balling in disc and pot-grate tests in COREM’s pilot plant were carried out to proof the concept, support the arising technology and evaluate its potential. According to first results, while CCS strongly improved, tumble and abrasion indexes as well dynamic LTD must be further investigated. Tests on four classes of equivalent carbon content pellets to evaluate layering strategy gave very good perspectives concerning the increase of productivity, and the reduction of fuel consumption and GHG emissions.

Oct 1, 2019

By Johanna Alegría-Ortega

Cr/CrN bilayer coating was deposited on AISI 440C by Cathodic Arc. The composition and structure of the Cr/CrN coating were investigated by scanning Electron Microscope, X-Ray Diffraction and X-ray Photoelectron Spectroscopy. The results show that crystal structure obtained was CrN phase with preferred [220] orientation. The hardness and adhesion of coating also were studied. The evaluation of erosion-corrosion (EC) on 440C bare and coated with Cr/CrN was performed by carrying out wear tests using a slurry jet with impingement angle 90° at 4 and 8 m/s. Corrosion, erosion and synergism wear rate were evaluated following the procedure described in ASTM G-119-09. This study presents that the synergism wear rate exceeds 40% of the total mass loss for coating and 60% of mass loss for the 440C, being the most aggressive wear component. The increase in impact velocity generated a rise in mass loss for both 440C bare and coated. The Cr/CrN coating offers better corrosion and erosion–corrosion resistance under all the tested conditions.

Aug 8, 2018

By Bruno Cordeiro Costa

Inseridas em um mercado extremamente competitivo, as empresas siderúrgicas vêm buscando aprimorar seus processos produtivos e de gestão de forma a reduzir custos de produção e garantir sua sustentabilidade. A principal parcela do custo de produção da empresa em relação a um aço inoxidável ligado ao Cromo e Níquel está na Aciaria, e a carga metálica representa mais de 80% deste valor. Visando aumentar a competitividade, foi aberto um projeto para otimizar a carga metálica na Aciaria. A redução da mistura de escórias é uma fase deste projeto. O propósito do presente trabalho é mostrar a metodologia adotada para otimizar o processo de recuperação de sucata das escórias de aços inoxidáveis, minimizando a ocorrência de misturas de escórias, para maximizar seus teores de Ni e Cr e, consequentemente, reduzir o uso de fontes mais nobres e caras destes elementos. Foi adotada a filosofia “Zero de Escória no Chão” e, para alcançar este objetivo, várias ações foram implantadas. Considerando 2011 como base 100%, o teor médio de Ni da sucata recuperada de 3XX aumentou 45% em 2013 e o teor médio de Cr subiu 36% na sucata recuperada neste mesmo período. Como consequência direta da redução da mistura de escórias de grupos de aços diferentes ao longo de todo fluxo produtivo, ocorre a redução dos residuais de Ni e Cr nos aços carbono e elétricos e de Ni nos aços 4XX. A metodologia adotada foi eficiente e os objetivos do projeto foram alcançados.

Jul 30, 2018

By Antônio Augusto Gorni, Fabio Adriano da Silva, Emanuelle Garcia Reis, Afrânio Márcio Costa

Gerdau Ouro Branco´s plate mill started the operation in 2016 with high level technology. Stands out the capacity to produce different thicknesses in a same plate, therefore allowing special service for sectors such as building structures, bridges, shipbuilding and mechanical applications. The purpose of this study is to present the first results obtained in this innovative product in Brazil. Some slabs of EN10025-2 S355JR+AR steel were rolled and were evaluated the dimensional tolerances, mechanical properties uniformity, grain size, surface and internal qualities. In addition, a correlation was observed between slab and plate thickness reduction and internal plate quality. The results show that this technology can be used with adequate performance for these steel grades in the current market.

Oct 1, 2019

By Leonardo Araújo Peruch, José Fagundes, Henrique Carneiro Pinto, Marco Túlio Costa, Nayara Coutinho, José Fabiano Martins Assunção

The objective of this project was to increase the hot charge by reducing reheating energy consumption and raising the productivity of ArceloMittal Tubarão's hot strip mill by changing the HSM’s schedule process with optimization of the relocation process of slabs after HSM’s chance with focus on slab temperature in reheating time. The project began with the revision of metallurgical rules for the relocation of materials, definition of criteria temperature setting (hot / cold), definition of restrictions of the process and review of modus operandi scheduling process. With the implementation of the process / system it is expected to achieve a 10% increase in the hot charge index in slabs reheating furnaces and increase productivity of the ArcelorMittal Tubarão hot strip mill

Oct 3, 2019

By Eduardo Piassi Nicoli

Este trabalho tem a finalidade de apresentar projeto para melhoria de qualidade e redução do consumo de água em torres de resfriamento sem a utilização de produtos químicos e ainda eliminando problemas de incrustações e acúmulo de metais pesados, corrosão e formação biológica, através de solução inovadora (novo modelo mental).

Oct 30, 2017