Search Documents

By Parker A. J, Ruane M, Wadley L. G B

Copper, sulphur, nickel, cobalt, palladium, silver, and gold can be recovered from the copper sulphide precipitated from the "copper boil" of the Sherritt-Gordon nickel process used at Western Mining Corporation's Kwinana nickel <refinery. The method is based on an oxidative ammonia leach of copper, nickel, and the precious metals at temperatures below 40°C to produce, in part, elemental sulphur, in the residue. This is followed by heating to decompose thiosulphate and remove some ammonia with precipitation of some of the copper, palladium, gold, and silver. Addition of sulphur dioxide to pregnant liquor precipitates copper, as either Chevreul's salt or copper(I) ammonium sulphite, together with the remaining gold and silver. Less than 10 per cent of the dissolved palladium and less than 1 per cent of nickel and cobalt precipitate to this stage.In one option, the Chevreul's salt is dissolved in a solution of copper(II) sulphate, acetonitrile, and water to generate a solution of copper(I) sulphate. Gold and silver do not dissolve. The solution of copper(I) sulphate is thermally disproportionated by distilling acetonitrile to give exceptionally pure copper powder, with desirable characteristics for powder metallUrgy. Nickel, cobalt, and ammonium sulphate are recovered from the motherliquor of the Chevreul's salt precipitation by return to the Sherritt-Gordon process, where recovery procedures already exist. Palladium is recycled for eventual removal as a sulphide with the gold and silver.In the other option, solid copper(I) ammonium-sulphite is <thermally disproportionated in water at 150°C to copper powder.

Jan 1, 1978

By Yi Luo, FENGLIANG WU

Explosions and fires originated from longwall gob due to the formation of methane-air mixture have been a severe threat to coal miner’s lives.Many numerical studies on coalmine fire and explosion hazards have focused on the airflow in roadways and mine gobs. However, most of these studies isolate the gob from its surrounding roadways, and the network analysis and the CFD method are applied independently tomodel the two classes of airflows. This approach greatly limits the ability of simulatingmine ventilation flow, especially unable to consider the effects of gob boundary conditions on air exchange between the gob and the surrounding airways. An innovative finite tube method (FTM) is developed to couple the one-dimensional mine ventilation network (MVN) and the 2D/3D gob flow field (GFF). In FTM, GFF is discretized into a finite number of flow tubes each of which is formed by any two adjacent stream lines. These tubes, representing the gob’s field flow, connect the MVN into a new coupling network. To solve the coupling model betweenMVN and GFF, an iterative solution technique is developed inwhich the MVN analysis is used to evaluate the boundary pressures for GFF simulation and in turn the FTM feeds the GFF results back to the coupling network. Based on the FTM approach, a model for gas migration in gob has been established for delineating the hazard zones of explosive methane concentration and spontaneous combustion. A computer program is developed to implement the FTM simulation. An illustrative example with five flow tubes representing the GFF is created to verify the stability and convergence of the FTM solution process. A simulation example also indicates that the accuracy of FTM is improved by 12% compared with previous method. Results of an application case show that the program is capable of quantitatively evaluating the gob’s risk zones prone for spontaneous combustion and gas explosion as well as performing risk analysis for various ventilation scenarios.

Jul 10, 2020

By T. Burchett, F. Stanley, K. McGough, G. Luttrell

The vast majority of U.S. coal preparation plants utilize screen-bowl centrifuges to dewater their fine clean coal products. In light of this popularity, researchers at Virginia Tech have engaged in a variety of laboratory and industrial field test programs to develop technological enhancements that have the potential to further improve the performance of this important solid-liquid separation process. These enhancements, which include simple design modifications and new reagent packages, have been shown to significantly improve solids recovery and reduce product moisture in several experimental trials.

Jan 1, 2006

By Alessandra Savazzini dos Reis

A indústria de cerâmica vermelha brasileira consome 10,3 bilhões de toneladas de argila ao mês para produção de telhas e blocos. Uma alternativa para tornar o setor mais sustentável ambientalmente é a incorporação de resíduos na massa argilosa. Na própria olaria são gerados resíduos, tal como, o resíduo de massa cerâmica crua originado na etapa de conformação das peças. Este trabalho visa caracterizar o resíduo de massa cerâmica crua para incorporação na massa argilosa usada em cerâmica vermelha. O resíduo de massa cerâmica crua foi caracterizado através de ensaios de FRX, DRX, calorimetria exploratória diferencial e termogravimetria, limites de Atterberg e distribuição de tamanho de partículas. Corpos de prova foram conformados, secos à 110ºC e queimados à 900ºC em forno industrial e foram submetidos a ensaios de absorção de água, porosidade aparente, massa específica aparente e resistência à flexão. Os resultados evidenciam que as propriedades cerâmicas avaliadas nos corpos de prova atendem aos valores das argilas-padrão brasileiras para uso em cerâmica vermelha.

Aug 16, 2017

By W. H. Gauvin, N. J. Themelis

I N ADDITION to its practical importance in the beneficiation of iron ores and in direct-iron processes, the study of the reduction of iron oxides involves many aspects of challenging theoretical interest. The complexity of the reduction process combined with the fact that under different experimental conditions the controlling stage for the reaction may not necessarily be the same, has led experimenters in this field to a wide diversity of opinion regarding the reaction mecl1anism. As a rule, each investigation has been restricted to the study of one or two variables over a comparative]~• narrow range of experimental conditions, and consequently, it be-comes necessary to examine the significance of each published work in the light of the results of other experimenters in the field.

Jan 1, 1962

By J. L. Kohler

This final report on Bureau of Mines Contract J0348005 presents the results of an investigation into the development of a Management Information System (MIS) for underground coal mines. The motivation for the research is the unrealized potential for increasing safety and productivity of the well developed mine monitoring system technology. The intent of this project was to examine the information issues, various design aspects of an integrated monitoring/MIS, and associated application concerns, such as the impact of this technology on safety. The work performed on this contract used mine ventilation as a prototypical example. The report is presented in five chapters and six appendices. In addition to the introduction and conclusions chapters, one chapter deals with ventilation MIS system requirements; another with the formulation of a knowledge-based expert system (KBES) structure to implement the integrated ventilation monitoring/MIS system, and one on the health and safety implications of the system. The appendices present details of the KBES system application with an example using a mine ventilation simulator (PSU/MVS). An important conclusion is that a KBES formulation of an integrated monitoring/ MIS for coal mine management is feasible and desirable.

Jan 1, 1986

By B. Erdem, N. Çelebi

An important problem associated with tandem dragline systems is that of matching the productive capability of individual draglines in the combination. In this paper, a dependence mechanism among draglines in a tandem system is described, and possible consequential problems in a poorly-matched system are defined. The rate of linear advance and the cost of stripping are determined as two major indications for an efficient operation. The proposed decision criteria and the underlying mechanism to select a synchronous couple are introduced and used in simulating tandem dragline systems. The developed model is tested on a hypothetical strip mine where pullback stripping is applied with a tandem dragline system.

Jan 1, 1999

By Gary Choate

The work presented in this report represents the background activity which led to the fabrication and testing of a greenhorn and crowd limit switch system for electric shovels. The program began With a literature search and manufacturers product review to gather material as a basis for concept generation. Visits to three open pit mines provided information from operation and maintenance managers which was useful in preparing design concepts. These concepts were evaluated through laboratory tests and engineering analysis to select a final design concept. The resultant greenhorn is four separate shock absorbing pads each enclosed in a housing which bolts to the end of a dipper handle adaptor. The plungers impact against stops mounted to the saddle block. The crowd limit control is a nonmechanical device which senses the location of the dipper and makes appropriate commands to the crowd motor to insure against impacting the greenhorns. The electronic crowd limit control is redundant and indicates malfunction modes. The greenhorn prevents shovel damage in the unlikely event of impact.

Jan 1, 1983

By Xin Wang, He Shao, Wenpu Li, Yiyi Zheng, Xi Chen, Yurong Gao

This study utilized experimental and numerical simulation methods to investigate and analyze the atomization characteristics of three internal air–water mixed atomizers under different operating conditions. By comparing the research results, the effective dust control working parameters for the application of the selected atomizer in the engineering field were determined. Firstly, the atomization characteristics of the three atomizers were studied using a customized experimental system. The results indicated that nozzle 2 had a wide atomization range, a small atomization distance, and small droplet size; nozzle 3 had a narrow atomization range, large droplet size, and fast atomization speed; and nozzle 1 not only had a large atomization range but also could produce droplets of dry mist size with fast atomization speed, meeting the dust reduction requirements of the Majiliang Coal Preparation Plant. Secondly, Fluent software was used to simulate the atomization process and particle size distribution of the three internal mixed atomizers, determining the working conditions of the atomizers, the required number of atomizers, and the application angle of the atomizers in the internal mixed dust removal system. Finally, the atomized dust control system was applied on-site, achieving a total dust removal efficiency of 90.72% and a respirable dust removal efficiency of 89.75%.

Mar 9, 2024

By Russell Griffin

The current state of the art of fire and smoke detection technology is reviewed from the standpoint of suitability for use in under- ground metal and nonmetal mines. Detection modes, fire signatures, and environmental considerations are included. Preliminary results of long- term, in-mine tests are presented.

By O. C. Blade

Diesel fuel is being used in greater volume than ever before in the United States. During 1950 railroads used 43 percent of the total volume of Diesel fuel sold, smelters, mines, and manufacturing plants used about 13 percent, highway vehicles such as trucks and busses, and equipment such as tractors and bulldozers accounted for approximately 20 percent, about 12 percent was used by water craft, and the remaining 12 percent by gas and electric utilities, the military forces, and oil companies. These figures were calculated from data issued by the Bureau of Mines. 2/ Comparable figures for 1951 and for 1952 to date are not available, but recent information indicates that well over 11,000,000 barrels of Diesel fuel per month are produced by the country's refineries. 3/ More information on this increasingly important type of engine fuel is needed by the petroleum industry, engine manufacturers, and consumers, particularly on the grades and qualities of the Diesel fuels being marketed. To supply this information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of Diesel fuel oil produced in refineries in this country.

Jan 1, 1952

By Michael G. Zabetakis

Vaporization of a solvent into an airstream at temperatures above the flash point of the solvent is hazardous if vapor is liberated at a rate that is sufficient to produce a flammable mixture. In may operations, the formation of such a mixture is prevented by rapid diluton of the vapors with air. The minimum air requirements for the dilution process are determined by the composition of the lower limit mixture at the temperature and pressure of interest. Because limits of flammability cannot always be calculated with sufficient accuracy for a proposed operation, they .rust often be determined experimentally. The present Bureau of Mines investigation was prompted by an application in which the lower limits of flammability of a number of solvent mixtures were required over a range of temperatures at atmospheric pressure. These limits were to be used along with available solvent-vaporization-rate data to establish minimum airflow rates needed to prevent the formation of flammable mixtures in an industrial process. Lower limits of flammability were determined for a number of mixtures containing methyl ethyl ketone, tetrahydrofuran, toluene, ethyl alcohol, and ethyl acetate in dry air-at atmospheric pressure and temperatures between 16° and 200° C. The experimental values were found to be in good agreement at with those predicted by Le Chatelier's law; variations with temperature were in fair agreement with those predicted by a modified Burgess-Wheeler law.

Jan 1, 1962

The 26th international APCOM symposium, hosted by The Pennsylvania State University, was held Sept. 16 to 20, 1996 in University Park, PA. Conducted about every 18 months throughout the world, APCOM symposia focus on the Application of Computers and Operations Research in the Mineral Industry. The APCOM International Council is the governing body of the symposia and determines the symposium’s locations and sponsorships. This group is composed of the nine permanent (voting) members. They include the University of Arizona, Colorado School of Mines, Pennsylvania State University, Society for Mining, Metallurgy and Exploration, Inc., Canadian Institute of Mining, Metallurgy and Petroleum, South African Institute of Mining and Metallurgy, Technical University of Berlin, Institution of Mining and Metallurgy and Australasian Institute of Mining and Metallurgy. The three nonvoting members are Moscow Mining Institute, China Institute of Mining and Rudarski Mining Institute of Slovenia.

Jan 1, 1996

A recent Evening Post Headline read 'Officialdoms Inertia Risking Millions in Growth Strategy'. The article beneath that headline outlined the difficulties encountered by the Government's growth strategy projects and included the paragraph 'public efforts by Government to brush up communication of the widespread nature of its growth strategy is believed to have been matched by efforts in private by some ministers to overcome their frustration at the constant delay while reports and paper work are moved between departments and through the system'. The article went on to point out that these delays could cost New Zealand millions of dollars in lost overseas exchange savings. We as responsible citizens should be appalled or at least concerned that such costly delays should or even could occur. But those on the outside of the system who spend much of their working life prodding, reminding, pleading, cajoling, even begging, the bureaucracy should be excused a smirk or a smile or even a good belly laugh. The Minister is usually a part of the bureaucracy passing judgment on someone else's proposals. This time the Government has plans of its own. Plans which it wishes to see implemented as rapidly as possible and even with the assistance of the precautionary National Development Act with its 'fast track' provisions those plans have got bogged down in the bureaucratic machine which this Government has done as much as any other to create. In the circumstances, the thought of Her Majesty's Ministers frustrated at the constant delay while reports and paper work are moved between departments and through the system is not unpleasing.

Jan 1, 1982

By Dale Ramsey

During Phase IV of our Landfill Mine Stabilization project at a coal burning power generating station, it was determined that a coal barrier pillar separating two abandoned areas of the deep mine had to be breached prior to expansion of the ash disposal area. The proposed plan by the landfill design engineers involved using a high pressure jet cutting tool to cut a slot to allow water flow to an existing industrial waste water treatment facility. Our plan proposed using explosives to breach the pillar from the surface reducing earth disturbance in a high quality watershed while reducing the project cost and accelerating the project time schedule. Many issues surfaced with the proposed change of using explosives. There were a number of lessons learned from this case history and is the primary basis of this paper.

Jan 1, 2003

By R. L. Rough, W. K. Overbey

The Bureau of Mines obtained samples of oil - reservoir rock from wells in Ohio , Pennsylvania , and West Virginia as part of an investigation of the susceptibility of petroleum reservoirs to secondary - recovery techniques . Illustrations and tables showing the geographic and stratigraphic sequence of the cored reservoirs and 40 tables of detailed lithologic descriptions of the reservoirs are presented . Information relevant to geologic surroundings , oilfield history , coring and well logging operations , and reservoir core analyses are referenced throughout the report .

Jun 1, 1970

Annual Meeting,Wallace, Idaho, Nov. 15-16, 1913. The third annual meeting, which was also the eighth consecutive meeting and the second to be held in the Coeur d'Alène district, was held in Wallace, Idaho, Nov. 15-16, 1913, with side trips to Kellogg-Wardner, Larson, and Mullan, where several mills were visited. The meeting was held jointly with the Montana Section, about 50 members and guests being present. Headquarters were in the Samuels Hotel, sessions being held in the public library. The arrangements and program were in the hands of the following local committee: George W. Roddewig, W. Earl Greenough, H. M. Childs. At 2.30 p.m., Nov. 15, the first session was called to order by Prof. F. A. Thomson, member of the Executive Committee, adjournment being taken to the Mine Rescue car, where Mr. Anderson and his assistant entertained the visitors for nearly two hours by demonstrations of mine-rescue and, first-aid practice, after which the party visited the Hercules mill, mention of which was made in the report of last year when the Section visited the plant. There are, however, several important alterations and additions to the flow-sheet to be noted, such as substitution of Chilean and Hardinge mills for the Huntington mills in the regrinding department; rearrangement of the tables and slimers, with a noticeable addition of the later models of the Franz machines, and the installation of the Wyman flotation process, which has been tried out, or is being tested, with more than ordinary success, on the middlings in several of the mills of the district, the Green Hill Cleveland mill being provided with a 100-ton unit, partly described below

Jan 12, 1913

By Jay W. Hawkins

Under an approved remining program, mine operators can remine abandoned coal mines without assuming legal responsibility for treatment of the previously degraded water, as long as the discharging waters are not further degraded and other regulatory requirements are satisfied. A U.S. Bureau of Mines review of 105 remining permits in Pennsylvania indicates that remining results in substantial reclamation of abandoned mine lands, utilization of significant quantities of coal, and reduction of contaminant loads (acidity and iron) from degraded mine drainage discharges. Normality tests performed on the water quality and flow data indicate generally nonnormal distributions and extreme right-skewness, tending toward lower values. The water quality of underground coal mines was observed to be more highly degraded in terms of acidity, iron, and sulfate than that of surface coal mines. The optimum baseline sampling scenario is 12 months in duration at a frequency of one sample per month. Analysis of water quality and flow rates before and after remining indicates that a majority of the mines exhibited either no change or a significant decrease in pollution rate because of remining. The discharge flow rate was the dominant controlling factor when the post-remining contaminant load was significantly better or worse than the baseline (pre-remining) load.

Jan 1, 2010

By V Shrotri L Muhmood, P Gandhre

The current work deals with the measurement of some thermophysical properties of Ca(NO3)2 based ternary nitrate molten salts as HTF (heat transfer fluid) / TES (Thermal Energy Storage) material for CSP (Concentrating solar power) plants. The density and viscosity of different compositions of the ternary salt mixture containing Ca(NO3)2, NaNO3 and KNO3 close to the liquidus has been experimentally measured. An attempt has also been made to measure the melting point of the salt using the cooling curve technique as well as Differential Scanning Calorimetry (DSC). Thermogravimetric analysis has also been performed to estimate the peak operating temperature of the salt. Compatibility of suitable pipe material (SS304) with molten salt has also been discussed. The salt mixture proves to be a viable alternative to the already existing HTFs like Therminol VP-1 (organic oil) or Solar Salt® in regards to its lower melting point, wider operating range, low cost, nontoxicity, sufficiently high density and comparable viscosity.

Jun 19, 2024

By Yukihiro Ishihara, Nanase Ogawa, Ming Lei

"Abstract In the Press-in Method, a static jacking force is used to install a prefabricated pile, while a reaction force is gained from previously installed piles. This piling technique has solved problems in urban piling construction such as noise and vibration associated with the piling work, restricted construction conditions due to the existing structures, and so on, since its emergence in 1975. Its applicability to hard ground conditions has been improved, with the development of press-in machines that involve augering or rotation. Besides, information such as time, penetration depth, jacking force and rotational (or augering) torque in piling work are automatically obtained. The concept of PPT, Pile Penetration Test, has been developed by the authors, to apply the obtained information to the processes of construction planning or foundation design. This paper highlights the technique to estimate SPT N value from data acquired in standard press-in (press-in without any auxiliary methods), press-in with augering and rotary press-in. The technique will be helpful in assuring the adequate embedment depth, re-selecting the adequate press-in machine or auxiliary method, and re-pricing the project objectively, particularly when a contractor encounters unexpected ground conditions.INTRODUCTIONThe Press-in Method is one of the piling techniques that use a static jacking load to install piles. It mitigates environmental problems of noise and vibration that have been associated with other conventional piling techniques.It is also featured by its spatial efficiency; since a ‘press-in’ piling machine gains a reaction force from the previously installed piles, there is no need of bulky weights that will occupy a large space. This feature is emphasized in the piling system in Figure 1, where a press-in machine and its related devices are all positioned and ‘walk’ on top of the pile wall.Its applicability to hard grounds has significantly been improved, with some newly developed piling machines that involve augering or that install tubular piles with teeth on the base by applying axial load and rotational torque at the same time."

Jan 1, 2014