Search Documents

By B. Weaver

Every year Pit & Quarry Magazine surveys the industry to produce their annual review. Here's a sampling of some of the statistics the survey produced from the end of the year 1994 survey.

Jan 1, 1995

By Saulo Brinco Diniz

As ligas de alumínio da série 7XXX são largamente utilizadas no setor aeronáutico devido sua alta razão resistência mecânica / densidade. O que proporciona uma alta resistência mecânica para as ligas da série 7XXX é a adição de elementos de ligas e tratamentos térmicos adequados, como por exemplo o T7351. Este trabalho teve como objetivo, estudar a evolução microestrutural de uma liga de alumínio 7475-T7351 processada por laminação convencional a temperatura ambiente, e posteriormente submetida a tratamentos térmicos de recozimento para recristalização. De acordo com os resultados apresentados, a amostra que foi submetida ao tratamento térmico de recozimento para recristalização a temperatura de 500ºC durante 15 minutos recristalizou, enquanto que a amostra que foi tratada a 350ºC durante 1500 minutos teve coalescimento dos precipitados.

Oct 30, 2017

By Frank A. Peters

This evaluation of the sulfurous acid process for the production of metallurgical-grade alumina is the first of a series concerning various known methods of extracting alumina from low-grade aluminous materials and was undertaken to permit comparison with other processes. In the process with which this Bureau of Mines report is concerned, calcined clay is leached under pressure with 20 percent sulfurous acid and then filtered to remove a siliceous residue. The aluminum sulfite remaining in the filtrate is precipitated as a monobasic sulfite which, together with iron sulfite, is then decomposed under pressure to form a crude alumina hydrate and iron oxide. This intermediate product is purified in a modified Bayer process to yield alumina suitable for electrolytic reduction to aluminum. A study estimate (16)3 is used for these evaluations. The capital cost, not including land, is estimated at $95,701,600 on a Marshall and Stevens index basis of 240.0 for a plant producing 1,000 tons a day of alumina or 350,000 tons a year. The annual operating cost for this size plant is estimated at $22,831,100 or $65.23 per ton of alumina using clay at $1 per ton. Depreciation and local taxes are included in the estimate, but profit and Federal taxes are not considered.

Jan 1, 1962

Principal component analysis of the variation of Cu, Ni, Zn, Pb, Mn, and Cr in a control group of 96 samples of surface ironstone from the Yilgarn Block, Western Australia, was used to derive a simple graphical method, based on only Cu, Ni, and Cr, for discriminating between massive nickel gossans and other ironstones.When the graph was tested by plotting 400 control samples, it failed to correctly classify only nine out of 176 gossans and 11 out of 224 other ironstones.

Jan 1, 1974

For 11 years, under authorization of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S.C. 321-325), and amendments, the Bureau of Mines has carried on an extensive research and development program to establish methods for producing oil from coal and from oil shale. This act was passed by the 78th Congress primarily because of the stress of wartime demands for liquid fuels to supply our armed forces during World War II. The act was progressively extended by the 80th and 81st Congresses, as later peace-time demand for oil and oil products continued to increase.

Jan 1, 1956

By James P. Ulery

Explosions in U.S. coal mines have caused death and injury to miners and destruction of workings since the first reported explosion in 1810. These explosions are caused when buildups of explosive gas and/or dust in the mine are ignited by the presence of a flame or spark. Methane gas is inherently generated and held by adsorption in coal and is normally liberated during mining. Because this gas is explosive in the range of 5%–15% by volume, fresh air is constantly supplied to the working face to prevent the methane/air mixture from reaching this explosive range. The required amount of ventilation air is based on estimates of gas release under normal conditions. Occasionally, unanticipated and unusually high emissions are encountered, which, despite normal ventilation controls, result in an explosive mixture that a spark from a cutting bit or electrical equipment can easily ignite. Investigations have shown that such emissions are often associated with anomalous geologic features or conditions. Although most operators are aware that certain geologic features may adversely affect productivity, few are aware of their potential as a gas emission hazard. This report presents a historical framework detailing the impact of geologic features on excess gas emissions and resultant mine explosions. It also provides operators with specific information on recognizing and alleviating potential hazards from methane emissions related to these geologic features.2

Jan 4, 2008

Tyre costs constitute 20-40 per cent of the operating cost of large haulage trucks, and tyre pressure maintenance is an important factor in minimizing costs.In the past, control over the hot (built-up) pressures of earthmover tyres has been inaccurate and inconsistent because it has not been possible, in a practical way, to measure the tyre's contained air temperature.A method for measuring this contained air temperature has now been devised using a bi-metallic probe thermometer inserted through the valve stem. Using these measurements in conjunction with a pressuretemperaturechart drawn up using the general gas equation, very accurate control over hot tyre pressures is now possible.

Jan 1, 1979

Development of automatic fire protection systems for large, mobile mine haulage equipment was initiated under Department of Interior's Bureau of Mines-FMC Corp. contract H0122053, "Improved Sensors and Fire Control Systems for Mining Equipment June 1972 to May 1973." After successfully designing and mock-up testing an effective economical automatic fire protection system, and after having demonstrated that the system could extinguish controlled fires on 100-ton capacity haulage trucks, USBM-FMC contract 110232059 was issued in June, 1973, to conduct further development and validation testing. This report documents technical progress and activity under the latter contract. Figure 1 shows areas of the two haulage trucks that were protected by the automatic fire protection systems tested during this program. Figures 2 and 3 are composites showing hardware and schematic diagrams of the systems tested.

Jan 1, 1974

By Noel N. Moebs

Valley Camp No. 3 mine was the scene of an experimental shortwall introduced in 1973 in an attempt to improve the recovery from the Pittsburgh coalbed in the Ohio Valley area where adverse ground conditions have imposed partial extraction methods with only 40 to 55 percent recovery of the valuable resource. The Bureau of Mines, under a cooperative agreement with Valley Camp Coal Co., monitored ground pressures and caving in the shortwall section in an effort to determine whether the roof strata, notably the limestone main roof, will cave to the extent that roof pressures at the face are relieved and whether the powered roof supports can sustain the roof load. The Bureau's efforts included mapping of clay veins, instrumentation of chain pillars and shortwall panels with encapsulated pressure cells, recording hydraulic pressures in the legs of the shortwall chocks, and core drilling underground and from the :surface. The experimental shortwall was a qualified success. Recovery increased 5.4 percent compared with partial extraction. Pressures in chain pillars and the abutment zone were not excessive. Hydraulic pressures in the chock legs did not approach the yielding pressure. Apparently, the limestone strata caved and the roof pressure at the face was relieved.

Jan 1, 1976

By Fábio de São José

Sistemas de moagem são projetados baseando-se, entre outros parâmetros, no consumo de energia das rotas existentes. Consideram-se custos com energia um desafio para a indústria mineral, pois a maioria da energia disponível ao processo é inevitavelmente absorvida pelos equipamentos e somente uma menor porção é destinada à fragmentação desejada. Hoje, a maioria das teorias utilizadas na avaliação do desempenho energético parte dos estudos de pesquisadores como Fred Chester Bond. De acordo com Bond, Work Index (WI) é um parâmetro representativo da resistência à moagem do minério, servindo para medir o consumo de energia na fragmentação e para comparar o comportamento de diferentes minérios. Estudos recentes comprovam que o WI de materiais em mistura pode ser medido, geralmente, com alto desvio devido às diferenças existentes de moabilidade de cada tipologia. Este trabalho consistiu na determinação do WI de minério de zinco silicatado com elevações nos teores de esfalerita (ZnS) e galena (PbS), devido à avanços na lavra, minério composto unicamente por willemita e suas misturas. Valores encontrados mostraram que a presença significativa de minerais de classes distintas daquele predominante na frente de lavra pode influenciar na determinação de parâmetros importantes para o processamento mineral. Amostras foram fornecidas pela Votorantim Metais Zinco.

Aug 8, 2018

By Warren L. J

The effectiveness of shear-flocculation as a method for upgrading simple mixtures of ultrafine (1-11 \lm) scheelite and garnet was evaluated. Statistical methods were used in the design and analysis of the main test program.The stirrer speed, stirring time, and initial weight ratio were all found to have significant effects on both the recovery and grade of the floes produced. The particle sizes also had an effect on the final grade. There were several important interactions between factors which also affected the results. Optimum conditions for shear-flocculation were established, and under these conditions about 80 per cent of the scheelite could be recovered at a grade which depended on the composition of the starting mixture. Starting with mixtures containing 10 and 50 per cent scheelite, the best final grades were between 20 and 50 per cent and between 70 and 90 per cent respectively, the actual value depending on the particular combination of particle sizes.

Jan 1, 1977

By Michael D. Justason

...a global perspective... In March of 2000, the Japanese Geotechnical Society added "Rapid Load Testing" to their national standard for pile testing. In the year 2000. it is estimated that there will be more than 500 "Rapid Load Tests" on foundations around the world. ...so what is a "Rapid Load Test", and why is it gaining acceptance and popularity?

Jan 1, 2001

By Gerald G. Griswold, Allan G. Provost

INTRODUCTION The Norad Expansion Project was located 10 miles southwest of Colorado Springs, Colorado, within Cheyenne Mountain. The expansion areas to be excavated would be adjacent to the existing underground Norad complex, which would remain in operation during the work on the expansion. The original complex had been constructed approximately eight years earlier and had been in full operation for approximately five years. Phase I, Excavation was awarded the Tiro Construction Corporation, a subsidiary of Harrison Western Corporation, Denver, Colorado, in the fall of 1970. Notice to Proceed was given to Tiro on 28 December 1970. The project owner was the U. S. Air Force, design was performed by the U. S. Corps of Engineers, Omaha District, who would also serve as the construction agency. [ ]

Jan 1, 1979

By M. D. Lackey

The "Art" of Big Hole Drilling has been in a continual state of evolution at the Nevada Test Site since the start of underground testing in 1961. Emplacement holes for nuclear devices are still being drilled by the rotary drilling process, but almost all the hardware and systems have undergone many changes during the intervening years. The current design of bits, cutters, and other big hole drilling hardware results from contributions of manufacturers and Test Site personnel. The dual string, air lift, reverse circulation system was developed at the Test Site. Necessity was really the Mother of this invention, but this circulation system is worthy of consideration under almost any condition. Drill rigs for Big Hole drilling are usually adaptations of large Oil Well drill rigs with minor modifications required to handle the big bits and drilling assemblies. Steel remains the favorite shaft lining material, but a lot of thought is being given to concrete linings, especially precast concrete.

Jan 1, 1983

Laboratory induced polarization measurements were made on representative samples of concentrated sulphide ores from three environments in New South Wales Comparisons were made with the membrane polarization exhibited by an argillaceous sandstone. The sulphide samples showed a strong polarization effect, the magmtude of whIch depended directly on the conductivity of tlIe pore electrolyte.

Jan 1, 1969

n the early days of the Hauraki goldfield (1866 to 1889) almost the only system of ore treatment was wet crushing followed by copper plate amalgamation. A further saving of bullion was in most cases obtained from the tailings by means of pans or berdans. Though this system was not always as efficient as might have been desired it answered fairly well for the bulk of the gold-bearing quartz of the Thames and Coromandel districts, where the gold occurs chiefly in the form of visible particles, and there is not a great deal of silver. It failed, however, with most of the ore found in the Upper Thames or Ohinemuri district, especially in the Karangahake and Waihi portions of the field. In those days the cyanide process was not, and the usual prescription of the mining " expert" was smelting. At Karangahake, many attempts were made to discover a payable method of treatment for the so-called" refractory" ore, but on thewhole with very 'little success, and the district struggled along for a number of years without adding very materially to the production of gold in New Zealand. At Waihi, the Martha Co.'s stamp battery treated by wet crushing and copper plate amalgamation some 18,000 tons from the Martha Reef, worth probablyat least £4 per ton, but the average return was considerably less than £1 per ton, a sum which barely paid working, expenses, and consequently the shareholders were glad...

Jan 1, 1903

By Peter J. Nicholson

During my more than 40 years in the practice of underground construction and engineering, the industry has seen progress from the dig down to rock or hardpan or alternatively drive concrete or steel into the ground and count the blows; then you can be sure of you have a solid foundation; to the modern day, I?m willing to try anything to save money. Of course these are both exaggerations, but not gross ones. After getting bored being supervision on jobs counting blows, I struck out into the new field of ?tie-backs? as they were called in the United States, or ?ground anchors? as they were then termed in the United Kingdom. After installing some of the first permanent ground anchors for the Corps of Engineers on Lake Michigan as well as the highest loaded rock anchors of the time at two dams on the Ohio River, we were at the top of our game in the 1970?s. Subsequently in the 1980?s when my view of the future of ground anchors saw their installation becoming a commodity item, we branched out into ?Pin Piles? now known as Micro Piles, high capacity, steel tube encased, small diameter (5-12? or so), high capacity (100-500 tons) piling. Next came soil nailing, both temporary and permanent retaining walls, as at Cumberland Gap Kentucky. My next morph was into ?Cement Deep Soil Mixing? earlier on, known simply as ?soil mixing?. For this education I traveled to Japan several times and established a long-term, Joint Venture, relationship with one of the better known Japanese specialty ground modification companies. In Boston at the ?Big Dig? we established the then record size soil mixing project, 500,000 or so cubic meters of CDSM concluding in the year 2000. Since then I?ve been involved as a consultant mainly for dams and levees. Below is the story of how I came to be at this place in the road to innovation in Geotechnical processes.

By L. Frederick

Measurement of gamma radiation occurring in nature to characterize geological formations has been widely recognized in mineral exploration. Different methods and apparatuses have been developed for drill hole logging purposes. Geological formations vary in amount of naturally emitted gamma radiation. A gamma signature from a geological formation is captured by utilizing different types of gamma detectors. A natural gamma radiation detector (NGRD) can be used to control mining whenever there is a significant difference between the radiation levels in the mineral or ore being mined and the waste materials surrounding the ore. Surface miners, such as the one shown in Figure 1, can precisely control the elevation of the cutter as the machine moves over the surface of the formation. This type of machine is predominantly used in selective mining operations, e.g. surface coal mining. If there is a means to know the position of the cutter relative to the interface between the ore and waste, the miner can recover all or most all of the valuable mineral with very little out-of-seam dilution. This paper discusses the results of a successful application of gamma detectors to control a surface miner at one of North American Coal Corporations? locations - Red Hills Mine. The mine has nine coal seams in total with thicknesses ranging from 12? to 60?. The bottom six seams (Figure 2) are minable. The mine has complex geology and a significant amount of annual rainfall (4.7 ft). The mine produces approximately 3.5 million tons of coal and about 40 bcy of overburden per year. The operation utilizes diverse mining equipment including Dragline Marion 8200, electric shovel P&H 2800, Caterpillar end dump trucks CAT 785 and 789; bulldozers CAT D11, D10, D8, and D6. Coal is mainly extracted by utilizing a Wirtgen SM 4200 surface miner that is loading CAT 785 trucks with high volume coal bodies and payload of 150 t. Operational cutting depth is 24 inches with maximum cutting depth of 36 inches. Surface miner operators determine a cutting depth based on multiple cues, the most important being visual observations of a coal seam being cleaned or mined. The cleaning process involves removal of the last foot of waste material covering the coal seam. This is one of two critical phases in the coal extraction process. If, during the cleaning process, an operator sets a cutting head too deep, valuable product is wasted. If it is set too shallow, waste material is left to be mined with the coal. The second critical phase occurs in the last cut on the interface between the coal and waste material at the bottom of the coal seam. If the cutting head goes deeper than favorable, then waste material is delivered to a power plant.

Feb 27, 2013

By R. M. G. S. Berezowsky

An atmospheric ammoniacal thiosulphate leach system was developed to recover gold and silver from residues of the ammoniacal oxidation leaching of sulphidic copper concentrates. Extractions of 88 - 95% Au and 83 - 98% Ag were attained within 2 to 4 hours at 40 - 60°C in thiosulphate leaching of the oxidation leach residues of Manitoba chalcopyrite concentrates analyzing 24.6% Cu, 0.18 oz/ton Au and 4.26 oz/ton Ag and a complex British Columbia chalcopyrite/tetrahedrite concentrate analyzing 18.5% Cu, 0.27 oz/ton Au and 276 oz/ton Ag. Parameters affecting the Au and Ag solubilization included thiosulphate, ammonia, and cupric ion concentrations, temperature, retention time and the degree of Cu extraction and sulphide oxidation in the primary oxidation leach. The precious metals were recovered from the thiosulphate liquors by zinc dust cementation.

Jan 1, 1979

By E. H. Burroughs

This bulletin is the sixth in the series of petroleum bibliographies published by the Bureau of Mines, Bulletins 149, 165, 180, 189, and 216 being compilations for the years 1915, 1916, 1917, 1918, and 1919- 1920, respectively. In this bulletin the same general plan has been followed in arranging the references, but one or two additions have been made in the classification.

Jan 1, 1921