Search Documents

By Wang Zhi

High-Mg-content concentrates are usually treated in Jinchuan flash smelting Furnace. Because the viscosities of high-Mg-content slag is very high, the operation of flash smelting becomes very difficult. To solve this problem, the viscosities of the semi-synthesized FeO-MgO-SiO2 slag of different compositions were measured. The results showed that when in the slag the weight percentage of MgO [w(MgO)] is 6-10%, the ratio of the weight percentage of iron to that of Si02, w(Fe)/w(Si02) is 1.1-1.4 and the temperatures are within 1473-1773K, the slag viscosities increased with the increase of W(MgO) and w(Fe)/w(SiO,). When w(Mgo)<6%, the smelting temperature should be controlled at I 300°C in order to to keep the smooth operation. When w(MgO)>10%, the temperature should be kept above I 633K. When the content of MgO is higher, a lower viscosity slag can be produced by decreasing the ratio of w(Fe)/w(SiO,). The appropriate ratio of w(Fe)/w(SiO,) for Jinchuan flash smelting furnace is about 1.2.

Jan 1, 2003

By John C. Machisak

THIS PUBLICATION presents injury experience and employment data for the nonmetal mining industry in the United States for 1960. Data for the mines and mills are presented separately, as shown in the list of tables. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry for their voluntary submission of injury and employment data. As the information submitted contributes largely to the promotion of safety in the industry, special effort has been made to ma e these questionnaires as complete as possible.

Jan 1, 1963

By Tjaar A. Louw, Albert P. Van Niekerk, Johannes J. Louw, Attie J. Goosen

Unlike molecular high explosives, commercial explosives based on ammonium nitrate do not detonate ideally according to the theoretical model for steady state, one-dimensional detonation. One of the reasons for this deviation from ideal detonation is the slower chemical reaction, due to less intimate contact between the oxidiser and fuel components. It is well known that the inclusion of gas pockets, such as microballoons, in the formulation of ammonium nitrate based emulsions and watergels enhances the performance of these explosives. Various different interpretations of the “hot spot” theory have been proposed to explain this phenomenon.

Jan 1, 1997

CONTENTS PAGE BAIN, EDGAR C.-The Nature of Martensite. Discussed by Ancel St. John, Henry S. Rawdon, Jerome Alexander, Howard Scott 1 FEILD, ALEXANDER L.-Effect of Zirconium on Hot-rolling Properties of High-sulfur Steels and the Occurrence of Zirconium Sulfide. Discussed by Beram D. Saklatwalla, Bradley. Stoughton, Andrew M&apos;Cance, George F. Comstock, Alexander L. Feild 12 SAUVEUR, ALBERT and KRIVOBOK, V. N.-Use of Sodium Picrate in Revealing Dendritic Segregation in Iron Alloys. Discussed by George F. Comstock, John H. Hall 17 KINNEY, C. L., JR.-Economic Significance of Metalloids in Basic Pig Iron in Basil Open-hearth Practice. Discussed by V. J. Pazzetti, George B. Waterhouse, C. L. Kinney, Jr 19 NEAD, J. H.-Absorption of Sulfur from Producer Gas in Open-hearth Furnaces.. Discussed by George B. Waterhouse, C. L. Kinney, Jr 26 PRIESTLY, WILLIAM J.-Effect on Steel of Variations in Rate of Cooling in Ingot Molds. Discussed by Emil Gathmann, Paul E. McKinney, George A. Dornin. 27 MONYPENNY, JOHN H. G.-Stainless Steel, with Particular Reference to the Milder Varieties (Stainless Iron). Discussed by P. A. E.-Armstrong, Beram D. Saklatwalla 33 ROYSTER, P. H., and JOSEPH, T. L.-Effect of Coke Combustibility on Stock Descent in Blast Furnaces. Discussed by Ralph H. Sweetser,. Richard Franchot, Sidney Cornell, T. L. Joseph 41 DAVIS, F. W., and BOLE, G. A.-Observations on Requirements of Refractories for Open Hearth. Discussed by C. L. Kinney, Jr., L. F. Reinartz, P. E. McKinney 46

Jan 5, 1924

By Emanuelle Garcia Reis

O trabalho apresenta a previsão das propriedades mecânicas de um aço C-Mn com adição de Nb laminado pelo processo TMCP, utilizando equações matemáticas que correlacionam os parâmetros operacionais de deformação e as temperaturas de processo obtidos em uma simulação laboratorial. Foram considerados os fenômenos metalúrgicos de solubilização, precipitação, recristalização e crescimento de grão. Os resultados finais previstos pela simulação mostraram-se satisfatórios, permitindo uma boa previsibilidade da resistência mecânica do laminado a quente.

Aug 16, 2017

By Wils L. Cooley

This report analyzes electrical accident data in the metal/non-metal mining industry. Accidents are categorized to determine their root causes. Special attention is given to accidents associated with inadequate or defective grounding of mine power systems. Recommendations are made concerning proper grounding practice, especially for dredges and for quarries in hard rock or sand. The costs of instituting the recommended practices are estimated for model mine power systems which are based on field data obtained from 37 mines and several electrical contractors. The expected benefits of various suggested safety practices are also estimated.

Jan 1, 1981

By L. J. Kane

Conventional methods for determining the size of dust suspended in a gas require that agglomerates (clusters of particles) first be broken into particles, but in evaluating industrial dust-removing equipment the size of the agglomerates as they actually exist in the gas stream is far more important. This paper presents results of an investigation by the Federal Bureau of Mines to develop methods for determining the size of dust agglomerates suspended in a gas stream. The studies are part of the Bureau&apos;s continuing research on synthetic liquid fuels. The size and size-distribution of agglomerates as they exist when the gas reaches the filter was determined by using a membrane filter in conjunction with a dust count under a microscope. A membrane filter is a cellulosic sheet about 150 microns thick containing millions of holes per square centimeter--holes of uniform diameter that run directly through the sheet without interconnection.

Jan 1, 1960

By E. E. De Beer

This paper describes a method for the determination of the settlement of an individual H-bearing pile, based on the results of CPT-tests. As implied by the nature of the problem, no analysis performed on one pile can be regarded as generally valid for a whole piling foundation project because, even on one site, the pile behaviour varies from one pile to another. Consequently, no precise mathematical analysis has been established; the proposed procedure represents a simple model for the determination of the probable settlement behaviour of an H-pile under a compressive load. Prior to the settlement computations, the rupture load and the resistance distribution along the pile have to be determined. Since the method for the determination of the H-pile bearing capacity from the results of CPT tests has been described elsewhere (de Beer, 1971, 72; de Beer et al., 1982; Arbed, 1985), no details will be given in this paper. The proposed method is valid for both uniform and non-uniform H-piles. The computed results have been satisfactorely compared to the static loading tests performed on different types of piles in clayey and sandy soils during an ECSC research program on H-bearing piles (1983-1987).

Jan 1, 1987

By M. John Brodie

This report reviews the regulatory environment as it pertains to waste rock management and disposal from mining operations, excluding coal and placer gold operations, in the \irate of Alaska. It is based on the EPA&apos;s staff position on an effective program to regulate mining waste as presented in the May, 1990 Strawman II document. The unique conditions which occur in pans of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a waste rock facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection, are examined.

Jan 1, 1992

By Associates

The headwaters of Skippers Creek and the Shotover River are reputed to be among the richest alluvial gold catchments in the world. This alluvial gold has no doubt been derived from reef systems similar to, and associated with, the Bullendale lodes. Physiographically the prospect covers steep ridges and deeply incised gullies between the Richardson Mountains in the west and the Harris Mountains in the east. Vegetation is mainly tussock with bush either side of Murdochs Creek. Access to the area is by metalled road to Skippers and then by 4WD track to Bullendale. Alternatively the prospect area can be reached by helicopter from Queenstown in around ten minutes.

Jan 1, 1992

By Randolph R. Dreher, Michael L. Schreder

"In recent years, FFE Minerals has designed, installed and commissioned several large grinding mill circuits. This paper discusses the issues related to the erection and commissioning of large grinding mill circuits. The three circuits discussed are Collahuasi in Chile, Minera Los Pelambres in Chile, and Century Zinc in Australia. These circuits include large SAG and ball mills with both gear and gearless drive arrangements, as well as, both trunnion and shell supported mills. Aspects of these features are discussed with respect to their impact on installation and commissioning. While the normal challenges of mill erection and start-up were experienced, there were also a few unexpected challenges encountered partly due to the large scale of the equipment. An overview of the equipment and design ratings of these circuits is also provided.COLLAHUASIOverviewThe Collahuasi mills were started-up in November of 1998. The site is located in the Andes Mountains at an elevation of 4300 meters. The grinding circuit includes two lines featuring one SAG mill and one ball mill for each line. The circuit features a recycle conveyor around the SAG mills with provision for adding a pebble crusher in the future. The design tonnage of the grinding plant is 60,000 MTPD with an ore BWI of 10.5 kWh/MT.The SAG mills are 32’ x 15’ (1 3’ EGL) with 10,800 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The mills are driven by low speed synchronous motors with CCV variable speed drives. The SAG mills are trunnion supported and use hydrostatic lubrication. Feed to the SAG mills is via a rock-box type feed chute on a cart. The mills discharge on to trommel screens with a bucket wheel to remove the oversize.The ball mills are 22’ x 36.5’ (36’ EGL) with 12,500 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The fixed speed mills are driven by low speed synchronous motors with GE Quadramatic load sharing drives. The ball mills are shell-supported and feature multi-pad bearings with hydrodynamic lubrication. The mills are fed via a rubber lined sump box with feed spout on a cart. The ball mills also discharge on to trommel screens. Twenty-six inch (26”) diameter hydrocyclones are in closed circuit with the ball mills."

Jan 1, 2001

By P. T. Brooks

Mineral nodules from the ocean floor represent a vast potential source of manganese, nickel, cobalt, and copper. Process development studies to devise methods for recovering these metals were conducted by the Bureau of Mines using two types of nodules--relatively low-grade calcareous nodules from the Atlantic Ocean and higher grade siliceous nodules from the Pacific Ocean. Ammoniacal carbonate leaching of reduced nodules appeared to have the best potential for processing the calcareous nodules, but the method proved to be impractical for recovering manganese. Extraction of 90 percent or better of the nickel, cobalt, and copper showed the technique to be attractive for recovery of these metals. The siliceous nodules appeared amenable to a process that starts with either a sulfur dioxide leach or a sulfation roast followed by a water leach to dissolve the soluble sulfates.

Jan 1, 1971

By Jarrett. K. M.

Nobody has, as yet, made a perfect machine. Therefore, when a machine is operating and functioning as it is designed to do, there is always some vibration present. This is easily and simply measurable with present-day equipment and any increase in the amount of vibration will indicate a potential failure. When an increase is noted, vibration analysis can pinpoint the cause of the potential failure and remedial action can be taken before an unscheduled shutdown is necessary or a breakdown occurs.

Jan 1, 1972

By Dyson N. F

Mixed cobalt-nickel sulphides precipitated from ammoniacal process liquors derived from nickel sulphide concentrates, mattes, and reduced nickeliferous laterites have been characterized.The mixed sulphides are prone to oxidation on standing and are rapidly leached under relatively mild conditions. The kinetics of the leaching reactions are controlled principally by temperature and oxygen partial pressure. Although the samples have different CO:Ni ratios and have undergone varying degrees of oxidation, there is little difference in their leaching behaviour. The results suggest that a single plant would be able to process mixed sulphides of varying composition. Any copper and zinc present in the mixed sulphides as impurities also go into solution and must be removed prior to recovery of the cobalt and nickel in metallic form.

Jan 1, 1981

By Zsuzsanna Zborovszky

Study of different parameters (minimum discharge voltage, minimum discharge current, wire electrode diameter, speed of separation, electrode materials, overlap of the electrodes, etc.), their direct effect on the power going into the discharge, and their indirect effect on the possibility of obtaining ignition with an 8.31% methane-air mixture from a resistive circuit. Critical evaluation of the Cadmium disc breakflash (the presently internationally recommended test apparatus). Description of experimental setup and apparatus.

Jan 1, 1974

In Mr. Weed&apos;s interesting paper, frequent reference is made to the Cananea copper-deposits, which are said to have been so vigorously exploited that they produced 14,000,000 Ib. of copper in 1901. The ore-bodies which yielded this large quantity of metal are described as a product of contact-metamorphism, and in Mr. Weed&apos;s genetic classification of such deposits, they receive a place under the sub-heading, "Deposits impregnating and replacing beds of contact-zone."* They are considered by Mr. Weed to represent a special type under this head, and are further classified as: " l. Chalcopyrite deposits: (a) Pyrrhotite ores; (6) Magnetite ores, Cananea type." In condensing much information into a comparatively small space, the presentation of a subject may be so abbreviated as to detract from its clearness. The situation at La Cananea, considering its importance from an economic as well as scientific standpoint, may he worthy of more detailed description. As Mr. Weed rightly remarks, " structural differences are so important, and have SO marked a bearing, not alone on the theory of their genesis, hut also on the working of the deposits and a determination of their value as mines, that they merit a full discussion."† It is my present purpose: (1) to show that it is doubtful whether the copper of La Cananea is mined, except to a limited

Jan 1, 1903

By Nissandro Domingues

Foi avaliada a possibilidade de aumentar a produtividade do aço IF processado via recozimento contínuo. Amostras laminadas a frio desse aço foram submetidas a ciclos térmicos de recozimento em escala laboratorial, empregando-se menores temperaturas de encharque e maiores velocidades de processamento que as praticadas industrialmente. Foram, então, medidas as propriedades mecânicas em tração e caracterizada a microestrutura do aço. A partir dos resultados mais promissores, bobinas foram processadas industrialmente nas mesmas condições simuladas em escala laboratorial. Em amostras dessas bobinas, foi avaliada, além das propriedades mecânicas e da microestrutura, a conformabilidade de blanks visando à garantia de atendimento dos requisitos de aplicação no cliente. Com os resultados obtidos, verificou-se que é possível produzir o aço IF satisfatoriamente, preenchendo todos os requisitos de aplicação, com um incremento de 10% na velocidade de processamento e uma diminuição de até 30°C, na temperatura de encharque. Esses resultados representam considerável ganho em produtividade no processamento do aço IF.

Aug 17, 2017

By A. Sobhy

Froth flotation is a widely used, cost effective coal cleaning process. However, its high process efficiency is limited to a narrow particle size range between approximately 50 to 600 µm for coal and 10 to 100 µm for minerals. Beyond this range, the efficiency of froth flotation decreases sharply, especially for difficult-to-float coal fines of weak hydrophobicity (e.g., oxidized coal). This study was aimed at enhancing recovery of an Illinois fine coal sample using a flotation column featuring a hydrodynamic cavitation nanobubble generator. Nanobubbles that are mostly smaller than 1 µm can be formed selectively on hydrophobic coal particles from dissolved air in fine coal slurry. Results indicate that combustible recovery of a -150 µm coal was increased by 5-50% for different size fractions in presence of nanobubbles, depending on process operating conditions. Other major advantages of the nanobubble flotation process include lower collector dosage and air consumption since nanobubbles are produced from air naturally dissolved in water and they act as a secondary collector on particle surfaces, thereby resulting in considerably lower operating costs. Key words: Cavitation; coal; froth flotation; nanobubble.

Feb 27, 2013

By Jorge Luís Coleti

A siderurgia mundial vive um momento de excesso de oferta, com isso as empresas necessitam reduzir custos por meio da melhora de processos e/ou através da substituição por matérias primas alternativas às convencionalmente utilizadas. Este trabalho trata justamente deste tópico e busca substituir a fluorita por outra fonte de fluxante, neste caso, o óxido de boro. Neste trabalho o óxido de boro foi adicionado a escórias sintéticas num banho de aço à 1600°C. Foram realizados testes com proporções de 3%, 5% e 7% de óxido de boro na composição das escórias. A fusão foi realizada em atmosfera inerte de argônio em um forno de resistência de dissiliceto de molibdênio. Amostras de aço foram removidas periodicamente a cada 5 minutos até os 25 minutos de experimento. Estas amostras foram analisadas em um espectrômetro de infravermelho. Os resultados indicam a viabilidade técnica para a aplicação do óxido de boro como substituinte da fluorita.

Aug 17, 2017

By Mandeep Singh

The smelting of lead ores has been carried out in southeast Missouri for centuries, and modern smelting practices have generated a variety of waste products. Lead blast furnace slag is one such product, which typically contains 10% zinc, 25% iron and 2% lead. This slag has often been stockpiled on the producing smelter site and accumulations have now reached several million tonnes. It is possible that in the near future these slags will be classified by the federal Environmental Protection Agency as hazardous, and therefore there is considerable interest in possible treatment processes to render the slags non-hazardous by removing the offending metallic elements. To ensure that the overall slag processing costs are kept to a minimum, it is imperative that lead and zinc be recovered in a form suitable for sale or further processing. There are two generic routes for processing blast furnace slags and they involve hydro-metallurgical or pyrometallurgical techniques. With hydrometallurgy, the slags would be leached directly and the metal values recovered from purified leach solution(s) by electrowinning. One problem with processes of this type is that the zinc and lead grades of the slags are low and the iron content is high, and thus the economics of metal production are often not favorable. For pyrometallurgical processing (1), it has been shown that the slags can be fumed to produce an oxide dust containing all the lead and zinc, and representing only a fraction of the weight of the initial slag. The oxide dust may then be processed hydrometallurgical to recover zinc and lead.

Jan 1, 1992