Search Documents

By Satyajit Vaidya, Rudolph Frizzi, Luis Berroteran

This paper presents design and construction challenges associated with a high-capacity rock-socketed drilled pile foundation system for a 60-story building recently constructed in an urban environment. The site is in very close proximity to surrounding 1-to-6-story buildings and a commuter rail subway tunnel structure. High compression, uplift, and lateral loads imposed by the tall, slender tower constructed over a relatively small site footprint posed a significant design challenge due to the close proximity of the subway tunnel and other structures. Construction challenges included those associated with advancing the drilled pile casings through overburden materials using internal flush method mandated by the Transit Agency, advancing the casings through very dense glacial till materials encountered above top of rock, and drilling rock sockets in variable rock conditions. This paper provides a brief overview of the site and subsurface conditions, and discusses the resulting design and construction challenges for the drilled pile foundation system and how they were addressed. SITE AND SUBSURFACE CONDITIONS The 8,350-square-foot site is located in a busy neighborhood in downtown New York City (NYC). Buildings neighboring the site are supported on shallow foundations, and their basements extend about 15 feet below the sidewalk level. A NYC-Landmarked building is located within a NYC Department of Buildings (DOB)-designated 90-foot influence limit from the Project site. NYC Transit Authority (NYCTA) subway tunnel and station structures are located in close proximity to the Project site. The subway tunnel structure extends about 50 to 55 feet below the sidewalk level. Although the upper portion of the tunnel structure is about 13.5 feet away from the site property line, the lower portion is only about 1 foot away from the property line. A site location plan is presented as Fig. 1. Geotechnical borings revealed subsurface conditions generally consisting of successive strata of surficial fill, sandy and silty soils, and glacial till (predominantly consisting of cobbles and boulders) overlying mica schist bedrock. A generalized subsurface profile is presented in Fig. 2. The surficial fill stratum was about 10 to 23 feet thick, and generally consisted of loose to medium dense sandy soils with varying proportions of silt, gravel, and miscellaneous debris such as brick. The underlying sandy and silty soil stratum was about 60 to 79 feet thick and generally consisted of loose to medium dense inter-bedded layers of fine to coarse sand, silty fine sand, and silt. The underlying glacial till stratum was about 26 to 70 feet thick and generally consisted of cobbles and boulders embedded in a very dense soil matrix. Top of bedrock was encountered in the borings about 110 to 150 feet below sidewalk level. Groundwater level was measured at about 30 feet below sidewalk level.

Jan 1, 2018

By J. N. Van der Merwe

"The probability of survival of coal pillars is a more rational indicator of stability than the safety factor. Over time, pillars undergo reduction in size by progressive scaling of the sidewalls. The probability of survival is therefore not constant but reduces over time. The rate of scaling can be quantified, and the reduction of the probability of survival as a function of time can therefore also be quantified. The paper describes the link between the factor of safety, probability of survival, and reduction of the probability of survival. Using the safety factor, probability of survival, and the time at which the probability of survival will reduce to 50% is proposed as a more rational method of evaluating pillar stability than the safety factor alone.IntroductionCoal pillar strength has long been the subject of research in South Africa and several other coal-producing countries. However, it began receiving serious attention only after the Coalbrook disaster in 1960. The most important outcomes of the initial investigations were the groundbreaking research by Salamon and Munro (1967) that resulted in the well-known power formula for pillar strength, and the work by Bieniawski (1969) that resulted in a linear formula for strength. The former approach was based on empirical back-analysis of failed and stable pillar cases, and the latter on in situ strength tests on large specimens.The Salamon and Munro (1967) formula has been widely used in South Africa and even adapted for application to hard rock pillars by researchers such as Hedley and Grant (1972).At the time of the initial work by Salamon and Munro, there were only 27 failed pillar cases suitable for analysis. It was not possible at the time to determine site- or seam-specific strength, and the result was a general formula for use in all seams in all mining districts. Since that time pillars have continued to fail and the database continued to grow – as of 2013, there were 85 cases in the database. Using the additional data, there have been a number of re-evaluations of the strength formula and it has also become possible to differentiate between the different mining seams and areas."

Jan 1, 2016

By C. M. Harrer

The location, features, quality, and extent of iron ore deposits are evaluated in this Bureau of Mines report. The results of pioneer beneficiation on Wyoming taconites and their success are discussed along with developments in the iron-ore mining industry, markets, and economics. Market potential, transportation, resource developments, taxation, cost of iron ore enterprises, and the future of Wyoming iron resources are evaluated. Although occurrences of iron ores in Wyoming were known prior to 1870, early production to 1900 was as a nonferrous metallurgical flux and as mineral pigment for paints. In 1901, the Hartville-Sunrise hematite deposits were available to the Western iron and steel industry and in 1962, the first western taconite operation was placed in production at Atlantic City, Wyo. This investigation disclosed the probability of other large iron deposits in Wyoming. Taconite in the Bradley Peak area of the Seminoe Mountains has a potentiality of 100 million tons; that in the Owl Creek Mountains may prove very large also. Pioneer beneficiation testing has been included, and results have been generally encouraging. Research continues on the large titaniferous magnetite deposits of Albany County, Wyo. At present high-density titaniferous magnetite is being mined and processed at Iron Mountain for heavy-aggregate and as a sized coating for underwater pipelines. Ample mineral raw materials needed for mining and processing Wyoming iron ores are available. Investments for iron-ore processing plants will generally be large, particularly for taconite and titaniferous magnetite.

Jan 1, 1966

By C. M. Harrer

The location, features, quality, and extent of iron ore deposits are evaluated in this Bureau of Mines report. The results of pioneer beneficiation on Wyoming taconites and their success are discussed along with developments in the iron-ore mining industry, markets, and economics. Market potential, transportation, resource developments, taxation, cost of iron ore enterprises, and the future of Wyoming iron resources are evaluated. Although occurrences of iron ores in Wyoming were known prior to 1870, early production to 1900 was as a nonferrous metallurgical flux and as mineral pigment for paints. In 1901, the Hartville-Sunrise hematite deposits were available to the Western iron and steel industry and in 1962, the first western taconite operation was placed in production at Atlantic City, Wyo. This investigation disclosed the probability of other large iron deposits in Wyoming. Taconite in the Bradley Peak area of the Seminoe Mountains has a potentiality of 100 million tons; that in the Owl Creek Mountains may prove very large also. Pioneer beneficiation testing has been included, and results have been generally encouraging. Research continues on the large titaniferous magnetite deposits of Albany County, Wyo. At present high-density titaniferous magnetite is being mined and processed at Iron Mountain for heavy-aggregate and as a sized coating for underwater pipelines. Ample mineral raw materials needed for mining and processing Wyoming iron ores are available. Investments for iron-ore processing plants will generally be large, particularly for taconite and titaniferous magnetite.

Jan 1, 1966

By Terry R. Neumann

This document, prepared for the U.S. Bureau of Mines Regional Mineral Assessment Program, presents data pertinent to the mineral resource assessment of the Needles 1° x 2° map quadrangle (excluding the Arizona portion), located in the Mojave Desert southeastern California. The U.S. Bureau of Mines (USBM) mineral survey of the quadrangle, conducted from 1991 to 1993, was done to provide the minerals data necessary to support effective land use planning and resource decision making. To this end, this report (1) inventories historic and current mining activity, (2) inventories identified resources, (3) provides an economic analysis; of identified mineral resources and estimates their feasibility for development, (4) delineates areas of exploration and development potential based on current geological, geochemical, and geophysical information, (5) supplies information on land status, transportation networks, power supplies, water availability, and regulations, and (6) analyzes socio-economic impacts of potential mining. The Needles quadrangle is in the Basin and Range province of the southwestern United Van. The area is underlain by a lithologically and structurally complex Proterozoic crystalline basement of gneiss and granite that is overlain by sparse, scattered outcrops of deformed and metamorphosed Late Proterozoic and Paleozoic sedimentary sequences. Mesozoic granitic plutons, particularly in the western half of the quadrangle, intruded the basement and sedimentary rocks, resulting in metamorphism and deformation responsible for the formation of high-grade gneisses and mylonitic rocks (core complex) in the eastern part of the quadrangle. Voluminous Tertiary volcanism unconformably overlie some older sequences. The structure of the area is dominated by Basin and Range extensional block faulting; in the eastern part of the area, block faulting is accompanied by widespread low-angle detachment faulting associated with core complex development.

Jan 1, 1993

By R. C. Bryce

"Selbaie is located northwest of Joutel, in what is known as the fourth east-west volcanic sediment group in northwestern Quebec. The main metals produced are copper and zinc, with important contents of both silver and gold. Production comes from an open pit mine on the A-I zone and from two underground mines on the B zone and the A-2 zone. Each mine gave rise to important capital investment programs for construction and mine development, all of which were managed and staffed with company-hired, non-union personnel. Production from all sources now exceeds 7000 tonnes per day, with a workforce of540 regular employees. Of particular interest technically is the high recovery of B zone reserves underneath 40 m of overburden cover, the low-cost capital development of the A-2 zone, the computerized control of open pit mining, and the successful copper-zinc separation of the A-1 zone ore. Due to the low grades of the mineral deposits, efficiency in all aspects of the production process, is essential to the success of the operation.LocationThe Selbaie Mine is located 82 km northwest of the locality of Joutel in northwestern Quebec (Fig. 1). Access to the mine is by an all-weather road, 32 km of which is paved. A second road access to the site is via La Sarre, 134km to the southwest. Employee access, materials transport and haulage of copper and zinc concentrates take place over both of these roads."

Jan 1, 1990

By Christopher Mark

Pillar recovery continues to be one of the more hazardous activities in underground coal mining. Safety requires that the roof above the intersection remain stable until after the pillar has been extracted. Artificial supports (timbers and Mobile Roof Supports) arc essential to roof stability, but so is the final remnant stump or pushout. Traditional mining practices usually called for the complete extraction of the final stump, but the recent trend (both in the U.S. and internationally) seems to be towards mining plans that leave a remnant stump. For this study, a sample of roof control plans from the Mine Health and Safety Administration (MSHA) Coal Districts were analyzed to determine current pillar recovery practices. Both full- and partial- extraction plans were included. Special attention was paid to whether plans require that a final stump be left, and whether requirements regarding the dimensions of the remnant stump are included. Foreign experience with final stumps is also summarized. It seems that the risk of major pillar falls can often be reduced by leaving final stumps that are large enough to protect the intersection, but small enough that they do not inhibit the caving of the gob. Because final stumps are often irregular in shape, a new approach for estimating their strength is described. Analyses were conducted to assess the effect of seam height and depth of cover on the potential variation in the size of remnant stumps.

Jan 1, 2001

By J. A. Botín

NPV is a static measure of project value which does not discriminate between levels of internal and external risk in project valuation. Due to current investment project?s characteristics, a much more complex model is needed: one that includes the value of flexibility and the different risk levels associated with variables subject to uncertainty (price, costs, exchange rates, grade and tonnage of the deposits, cut off grade, among many others). Few of these variables present any correlation or can be treated uniformly. In this context, Real Option Valuation (ROV) arose more than a decade ago, as a mainly theoretical model with the potential for simultaneous calculation of the risk associated with such variables. This paper reviews the literature regarding the application of Real Options Valuation in mining, noting the prior focus on external risks, and presents a case study where ROV is applied to quantify risk associated to mine planning.

Jan 1, 2012

By Frank Sames

Most Blasting Programs are developed focussing on the environmental impact with respect to blast vibration and airblast. Compliance with existing regulations or policies limiting the immissions are generally achieved through constrains in the blast design, or monitoring programs. Efficient monitoring programs combine compliance monitoring and blast assessment. Signals, which are obtained in the area of direct influence of the seismic source, can contain valuable information about the blast design parameters. Techniques to analyze blast vibration signals have advanced and can assist in understanding the contribution of individual blast parameters to blast vibration and airblast. Advanced signal analysis encompasses magnitude analysis, Fast Fourier Transforms (FFT) and frequency scans in the frequency domain, as well as filtering in the time domain. Through examples, the advanced signal analysis techniques and their limitations are described and discussed, showing the impact of blast timing, timing accuracy, charge configuration and the geology dependent transmission behavior. Optimization criteria and pragmatic monitoring programs can be developed on the basis of the most influential blast parameters. In addition, however, safety and the cost efficiency of the blasting program are essential to the success of an operation. That is where advanced signal analysis techniques can interface with blast planning, computer assisted modeling and information systems. A valuable process can be developed to ensure compliance with existing regulations and efficient risk management for mining operations, while tracking cost and supporting operational decisions. A conceptual blasting information system is presented.

Jan 1, 2000

Extending an organization?s knowledge base throughout the entire enterprise can improve operations. Until recently, though, field operations were often left out of the information loop, as extending high-bandwidth communications into harsh environments often proved impossible due to thermal extremes, physical hazards and caustic chemicals. However, advances in the design and manufacture of rugged fiberoptic cables have now enabled the successful installation of 10-gigabit transmission links to places such as mining operations. The experience of Consol Energy exemplifies how plant managers can successfully enlist ruggedized tight buffered cables to help carry the efficiency of ERP communications into even the most challenging work environments. ?As part of our ERP implementation, we extended our corporate network underground into our mines using fi beroptic cable,? said Tom Prokop, manager-site support for Consol Energy. ?We?ve actually had rooffalls bury the cable between rocks and still did not lose data communications. Our maintenance personnel are now able to access our ERP system while underground at locations that can be up to 32 km (20 miles) away from their desks or the warehouse. Access to the corporate network allows them to order parts, look at electronic schematics, access monitoring data, no matter where they are in the mine. With a few hundred workers below ground, this immediate access translates into a time-savings that adds up in a hurry.?

Jan 1, 2009

By G. Diáz

The PLACID process applied to the recycling of spent lead-acid batteries is being developed by an European Consortium within the Brite-Euram II programme. The status of the project entitled "Lead Recovery from Lead Oxide Secondaries" is described in this paper. The main laboratory and batch experimental results and the preliminary feasibility study are summarised. The description of the demonstration pilot plant and continuous campaigns programme for 1995 are also included. An interesting global approach is proposed, integrating the Placid process in the existing spent battery recycling pyrometallurgical facilities. This yields important improvements in the overall process. Grids would be easily treated by the conventional pyrometallurgical route, obtaining lead alloys,, while battery pastes, slags and fumes would be fed to the Placid process, obtaining pure electrolytic lead (>99.99 %), ideal for battery paste manufacturing. The implementation of the Placid process into the existing battery recycling pyrometallurgical facilities is analyzed from technical, environmental and economical viewpoints. Greater overall lead recovery, lower operating costs, reduced waste production, environmentally safer residues and much better lead product quality are the key advantages. The authors draw the following final conclusion : Integration of the Placid process with conventional pyrometallurgical treatment is a feasible and very attractive alternative route for spent lead-acid battery recycling.

Jan 1, 1995

By C. F. Gleeson, D. G. Sheehan

"The results of humus and overburden geochemical surveys over the Doyon, Bousquet and Page-Williams gold ore deposits are presented.These studies show that humus sampling for gold gives negative results over the Doyon deposit. The lack of response is probably caused by the presence of 1 m of relatively impermeable glaciolacustrine clay and silt that overlies 1 m to 2 m of till over the surface expression of the ore zone. By contrast, positive responses for gold occur in humus samples over the Page Williams A and C gold deposits. The ""A"" ore zone is covered by several metres of exotic calcareous till over 0.5 m to 1 m of older, locally derived till. Anomalous values for gold in humus range from 10 to 35 ppb over the orebody. Overburden over the ""C"" ore zones is much thinner, generally it consists of less than 2 m of sandy till. Trenching humus anomalies that range from 10 to 1360ppb Au uncovered the gold mineralization. The geochemical dispersal trains in till from the Doyon orebody and the Page-Williams ""A"" zone are relatively short (i.e. less than 200 m) because both deposits occur in the lee of bedrock highs that shielded them from extensive glacial quarrying. Dispersal trains from all three pyritic gold deposits can be defined using either the fine fraction or heavy mineral fraction of the till.The intensity of the gold in till anomalies over the ore zones is variable. Therefore, it would be misleading to attach rigid significant threshold gold values to overburden drilling results. Each case must be evaluated based on bedrock topography, sample density, overburden type, thickness of till, as well as size, type and orientation of the target exposed to glacial erosion."

Jan 1, 1987

By V. R. Miller

The Bureau of Mines developed and evaluated a detecting and sorting device to separate the copper-bearing portion from the barren portion of Michigan native copper ore in the minus 4- plus 1-inch size range. Small-scale sorting tests were also conducted on minus 1- plus 1/2-inch material from the Centennial No. 6 mine, using a previously developed system that was modified to increase sensitivity. Results showed that, with the added sensitivity, 85 to 90 pct of the copper in the minus 1- plus 1/2-inch material could be recovered in about 50 to 60 pct of the fraction. Sorting tests on minus 4- plus 2-inch and minus 2- plus 1-inch fractions from the Centennial mine were conducted with the large sorting system. Results showed that 86 to 93 pct of the copper was recovered in 43 to 64 wt-pct of the sorted fractions. Combining of concentrates from the two fractions resulted in a recovery of 90 pct of the Popper in 55 pct of the weight. The composite concentrate contained 2.40 pct copper, and the tailing analyzed 0.33 pct Cu; the head sample assayed 1.46 pct Cu.

Jan 1, 1978

By D. Peatfield

The design and operation of coal preparation plants are governed by the inherent quality of the raw coal to be processed, market specifications and the saleable tonnage requirements. Topography influences the layout of the plant but does not affect the process design. The coal market comprises many sectors, each having specific requirements with respect to both size and quality. In turn, these have led to different levels of preparation and the development of specific types of coal preparation plant design. Developments in processing techniques and processing equipment have also influenced the design and now give the preparation engineer numerous permutations in process and equipment selection. This paper gives an overview of the coal industry in general and summarizes some of the developments in the design of plants and technical developments in the areas of dense medium processing, fine coal treatment and equipment design.

Jan 1, 2003

By Joan T. May

Federal Bureau of Mines studies showed that some organic amine hydrochlorides can be used as dehydrating agents for producing anhydrous magnesium chloride from hydrates and brines. Laboratory-scale tests showed that double salts are formed by reacting 35 percent magnesium chloride brine or spray-dried magnesium chloride with pyridine hydrochloride. Heating decomposed these double salts to anhydrous magnesium chloride and recycle pyridine hydrochloride. Pyridine hydrochloride also chlorinated any magnesium oxide in the spray-dried magnesium chloride. The anhydrous magnesium chloride obtained by the method described contained less than 0.8 percent oxygen. More than 98 percent of the organic amine hydrochloride was recovered.

Jan 1, 1978

Gas-liquid contacting in the packed bed is a common operation in metallurgical reactors. Research has shown that, unlike wetting flow, non-wetting liquid flows in the form of discrete droplets or rivulets. Thus, modeling of the liquid phase as a continuum is in contradiction to the observations. Also, for the non-wetting case, continuum models have failed to describe liquid flow path when the liquid source is a point source. The aim of the current work is to put forward a combined Lagrangian-Eulerian approach to model the liquid and gas flow in the packed bed. Liquid is assumed discrete and modeled using a force balance approach. Gas is assumed to be interpenetrating continua and modeled using k-emodel for turbulent flow. Structured packing is assumed and x- ray imaging technique is used to visualize liquid flow lines in the bed. Simulation results for liquid flow path compared with the experiments.

Jan 1, 2006

By K. Yamaguchi, Sekimoto. H.

"Platinum Group Metals (PGMs) used as catalyst which reduces toxic substances in emission gas exhausted from an automobile should extensively be recycled because they are rare metals produced only at the limited regions. The recycling process is to smelt an alumina honeycomb, in which PGM is built, in molten iron with flux such as lime and silica to separate them. PGMs are concentrated in molten iron while alumina in slag.The objective of this study is to understand the factor to concentrate PGMs in liquid iron as much as possible. Fundamental research of the distribution of the PGMs between the slag and liquid iron was carried out to recover the value metals of platinum, palladium and rhodium from the three-way auto catalyst. The distribution ratios of platinum, palladium and rhodium between the Al2O3-CaO-SiO2 slag and liquid iron are from 10-6 to 10-5, and these are concentrated in comparison with slag phase by about 1 million times to the liquid iron at 1873 K. The distribution ratios of platinum between the FexO-CaO-SiO2 slag and liquid iron decrease from 0.1 to 2?10-4 with increasing the CaO content in the slag. The CaO addition to the FexO unary slag is effective in concentrating platinum in molten iron.Based on the distribution ratios obtained in this work, recovery of PGMs was determined. The recovery of platinum, palladium and rhodium increase with increasing the mass ratio, Mmetal/Mslag. In the case of the conditions of Mmetal/Mslag = 0.04, the recoveries of PGMs showed more than 99.97%. The use of liquid iron and carbon saturated liquid iron as the collector metal is advantageous for the PGM recycling of the three-way auto catalyst. We found that PGMs are enriched to the molten iron or the carbon saturated iron and the slag loss of PGMs is negligible small."

Jan 1, 2014

By R. Venugopal

The paper reviews the development of Mineral Engineering education and training programmes in India. It highlights the major academic programmes and describes the evolution of the curriculum and design of courses in response to the changing requirements of India?s mineral and coal industries. An outline of the efforts needed to sustain and further improve the existing programmes is also provided. Keywords: manpower, mineral engineering

Sep 1, 2012

By H. Stanley Benson

This report is an account of research conducted to improve the performance of and then further field test Draft Power Sensor (DPS) equipment, the use of which enables a bulldozer operator to optimize his machine's work rate. Significant improvements were made in DPS hardware, and extended field testing was conducted at two working strip mines: the Glenharold Mine of Consolidation Coal Company, near Stanton, North Dakota, and the Beulah Mine of Knife River Coal Company, near Beulah, North Dakota. This report documents the increase of bulldozer work production by greater than twenty percent while using the Draft Power Sensor when compared to baseline work production without benefit of the Draft Power Sensor. Research was done by Southwest Research Institute under contract with the Bureau of Mines.

Jan 1, 1980

By D. A. Cormode

"INTRODUCTIONPine Point Mines, operated by Cominco Ltd., is located approximately 55 miles east of Hay River, N.W.T. by the southern shore of Great Slave Lake.The milling operation commenced in the fall of 1965 at a design capacity of 5,000 tpd. An addition which came on stream late in 1968 raised the nominal capacity to 8,000 tpd. Currently the milling rate is 11,000 tpd.The lead and zinc sulphides occur in dolomite host rock. Typical feed grades at present are 2% lead, 5.5% zinc and 5 % iron. When dolomite is present even in relatively minor amounts in the zinc concentrate, it presents serious treatment problems and causes inefficient operation of electrolytic zinc refineries.By 1972, it had become apparent that magnesium rejection in the form of dolomite was deteriorating because of increased plant throughput of less amenable ore. This paper will briefly outline the Pine Point zinc flotation circuit and will discuss the two phase program for reducing the magnesium level in the zinc concentrate. The program included changes and alterations to the flotation circuit and the construction of an acid leaching plant."

Jan 1, 1977